Search Results

Search found 20448 results on 818 pages for 'ip address'.

Page 203/818 | < Previous Page | 199 200 201 202 203 204 205 206 207 208 209 210  | Next Page >

• MS Server 2008 R2: DNS Redirection on second server for website

  - by Alain

  We have a website on a secondary server that we want this website to be accessible from Internet, with www.mywebsite.com. In the domain name provider of www.mywebsite.com, we set our 2 dns names, dns1.company.ch, dns2.company.ch and our static ip address. System is set as following: MS Server 2008 R2 N°1: Main server, in AD With IP 192.168.1.100 With DNS zone dns1.company.ch With DNS secondary zone from server N°2: dns2.company.ch With DNS secondary zone from server N°2: mywebsite.com (zone transfer is on) MS Server 2008 R2 N°2: Secondary server, not in AD With IP 192.168.1.101 With DNS zone dns2.company.ch With DNS zone mywebsite.com with host: 192.168.1.101 With the website under ISS with bindings www.mywebsite.com:80, mywebsite.com:80 All traffics for ports 80 (http) and 53 (dns) from Internet goes to server N°1. How can we redirect all traffics for www.mywebsite.com from Internet to our secondary server so the corresponding website can be displayed in Internet ? Note: Under DNS of server N°1, we tried to use also a conditional redirector mywebsite.com (192.168.0.101), but it was working only for intranet. Thank you, Alain

  Read the article

• Two Network Adapters on Hyper-V Host - Best way to configure?

  - by GoNorthWest

  Hi, I have two physical network adapters installed in my Hyper-V host. I want one to be dedicated to the host, and the other to provide external network services to the VMs. Would the appropriate configuration be as such: Leave the first physical network adapter alone, assigning it the host IP, but not using it to create any Virtual Netorks For the second physical adapter, I would create an External Network, along with a Microsoft Virtual Switch, and use that to provide network services to the VMs. Each virtual NIC for the VM would be associated with that External Network. A static IP would be assigned to this adapter, and each VM would be assigned a static IP as well. The above seems reasonable to me, but I'm not sure if it's correct. Does anyone have any thoughts? Thanks! Mark

  Read the article

• Ping "replies" from same computer with 'Destination host unreachable' (no route to other computer)

  - by Srekel

  I've got two computers in a LAN behind a wireless router. One has XP with ip 192.168.1.2 This one has W7 with ip 192.168.1.7 If I try to ping the other one from this computer, I get this: C:\Users\Srekel>ping 192.168.1.2 Pinging 192.168.1.2 with 32 bytes of data: Reply from 192.168.1.7: Destination host unreachable. Reply from 192.168.1.7: Destination host unreachable. Reply from 192.168.1.7: Destination host unreachable. Reply from 192.168.1.7: Destination host unreachable. Ping statistics for 192.168.1.2: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Tracert gives the same result: C:\Users\Srekel>tracert 192.168.1.2 Tracing route to 192.168.1.2 over a maximum of 30 hops 1 Kakburken4 [192.168.1.7] reports: Destination host unreachable. Trace complete. Although I can ping and tracert the router without any problems. I have disabled the firewalls on both computers. The router is set to use DHCP (if that matters). Here is the output from "route". C:\Users\Srekel>route print =========================================================================== Interface List 13...00 25 86 df c6 89 ......TP-LINK Wireless N Adapter 12...e0 cb 4e 26 b9 84 ......Realtek PCIe GBE Family Controller #2 11...e0 cb 4e 26 be 94 ......Realtek PCIe GBE Family Controller 1...........................Software Loopback Interface 1 16...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 14...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.7 20 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.1.0 255.255.255.0 On-link 192.168.1.7 276 192.168.1.7 255.255.255.255 On-link 192.168.1.7 276 192.168.1.255 255.255.255.255 On-link 192.168.1.7 276 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.1.7 276 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.1.7 276 =========================================================================== Persistent Routes: None IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 14 58 ::/0 On-link 1 306 ::1/128 On-link 14 58 2001::/32 On-link 14 306 2001:0:5ef5:73ba:881:20c1:3f57:fef8/128 On-link 14 306 fe80::/64 On-link 14 306 fe80::881:20c1:3f57:fef8/128 On-link 1 306 ff00::/8 On-link 14 306 ff00::/8 On-link =========================================================================== Persistent Routes: None I've set up and debugged a few networks in my life but I'm not really an advanced network user, so I'm not sure what might be wrong. Any ideas? Oh, and pinging this computer from the other computer doesn't work either. EDIT: Adding arp output: C:\Users\Srekel>arp -a Interface: 192.168.1.7 --- 0xd Internet Address Physical Address Type 192.168.1.1 00-1f-33-ef-28-01 dynamic 192.168.1.255 ff-ff-ff-ff-ff-ff static 224.0.0.22 01-00-5e-00-00-16 static 224.0.0.252 01-00-5e-00-00-fc static 239.255.255.250 01-00-5e-7f-ff-fa static 255.255.255.255 ff-ff-ff-ff-ff-ff static Adding ipconfig... C:\Users\Srekel>ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : Kakburken4 Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No Wireless LAN adapter Wireless Network Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : TP-LINK Wireless N Adapter Physical Address. . . . . . . . . : 00-25-86-DF-C6-89 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 192.168.1.7(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : 09 April 2010 23:09:45 Lease Expires . . . . . . . . . . : 10 April 2010 23:09:45 Default Gateway . . . . . . . . . : 192.168.1.1 DHCP Server . . . . . . . . . . . : 192.168.1.1 DNS Servers . . . . . . . . . . . : 192.168.1.1 NetBIOS over Tcpip. . . . . . . . : Enabled Ethernet adapter Local Area Connection 2: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller #2 Physical Address. . . . . . . . . : E0-CB-4E-26-B9-84 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Ethernet adapter Local Area Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller Physical Address. . . . . . . . . : E0-CB-4E-26-BE-94 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Tunnel adapter isatap.{74D5C406-894E-4000-8DE7-6AAEBF7C8382}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Microsoft ISATAP Adapter #2 Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Tunnel adapter Teredo Tunneling Pseudo-Interface: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes IPv6 Address. . . . . . . . . . . : 2001:0:5ef5:73ba:881:20c1:3f57:fef8(Preferred) Link-local IPv6 Address . . . . . : fe80::881:20c1:3f57:fef8%14(Preferred) Default Gateway . . . . . . . . . : :: NetBIOS over Tcpip. . . . . . . . : Disabled

  Read the article

• PEN daemon as load balancer, IIS web logs not showing true requester IPs

  - by Aszurom

  I have a Hercules vmware appliance, which is a micro-linux vm that runs the PEN daemon and acts as a server load-balancer. It takes any incoming request on the appliance's IP and routes it out to a number of alternate IPs. The logs of the daemon show the true IP of the browsers hitting the website. The logs of the websites themselves (iis 6 and 7) only show the requester IP as being that of the load balancer. The IT manager tells me that when we had a hardware appliance (serveriron XL) doing the load balancing, the web logs reflected the requester IPs accurately. Is there any way to get this resolved with the daemon, or will I be digging that out of the closet and plugging it back in?

  Read the article

• How to prevent Ubuntu from combining networks on 2 NIC server?

  - by SolarPower

  I've got a Ubuntu Server 10.10 with 2 network interfaces with a cable plugged into both going to switches on completely different networks with different routers. One network is the 10.1.10.X network with a separate gateway/router - the server has an IP of 10.1.10.50 with the gateway IP of 10.1.10.1. The other interface is 10.2.10.X, IP 10.2.10.50, gateway 10.2.10.1. All my Mac machines are on the 10.2.10.X network, and all servers on the 10.1.10.X. The ONLY connection between the two is this machine. From a Mac in my office, I CANNOT ping any computer on the 10.1.10.X network except the Ubuntu machine I'm talking about. However, under the Shared column in Finder, I can see every server on the other network listed. That makes me believe that somehow this Ubuntu machine is letting certain requests span both networks, which is a security problem. Hope this is enough info.

  Read the article

• www a-record vs cname-record

  - by Sorin Buturugeanu

  Hi! I have a website that I will be hosting DNS for (testing purposes at first and then it will have some limited traffic). I have set up DNS so that site.tld has an A record to the actual IP but I don't know what to do about www.site.tld. Both site.tld and www.site.tld will point to the same server / application so my logic tells me to add a cname record so that www.site.tld becomes an alias for site.tld, BUT, I've been checking my settings with intodns.com and if I only add a CNAME for the www.site.tld it gives me the following error: ERROR: I could not get any A records for www.cexa.ro! (the error clears once I do an A record for www.site.tld to point to the actual IP) I don't know if there is a "rule" that "www." should always be an A record even though it's actually pointing to the same IP / application. Thanks for helping me understand this!

  Read the article

• Need help connecting to NAS externally-port forwarding and DDNS newbie

  - by Joel

  Hi folks, I just picked up a synology NAS, and I'm loving it for internal use, but I want to be able to access the NAS externally-both from my iPhone (3G) and from the net. I have a Linksys WRT54G-TM router. My first question is whether I have set up the dyndns correctly. On my computer that is on my network, if I put in mydomain.dyndns.org, I am taken to a password popup and when I enter my router login and password, my router admin page opens up. On the same computer, I get the same results if I use my external IP address, and if I use my internal IP 192.168.0.1 So that is all as expected. However, when I go to my iphone and turn off wifi, and try to connect with 3g to the external IP or the dnydns domain, I just get an error "Safari could not open the page because the server stopped responding". What's up?

  Read the article

• IIS7, different ports for websites but no portnumber in the browser

  - by Queensheep

  I have a windows server 2008 with IIS7 with 4 websites. In DNS I have 4 different URLs which point to the IP of the server. I configured each web site with the site bindings: website1: hostname: url1, port: 80, IP-Adresse: the adress of the server website2: hostname: url2, port: 80, IP-Adresse: the adress of the server The result is, that from the client, I can browse with all the 4 URLs to the specified web sites and everything is fine. Then I changed in IIS the port of the websites, so that website1 now uses port 8080, website2 uses port 8081, and so on. Now I have to use the browser with the url and the portnumber (like URL:8080). Is there a possibility, to configured the websites with different portnumbers but not to use the portnumbers in the browser?

  Read the article

• Can't connect to Windows Server 2008 shared folders via VPN connection

  - by Pearl

  I set up an VPN connection on my 2008 server using RRAS. The VPN seems to work fine. I can connect from outside the network. I am also able to establish a remote access connection via the VPN-IP. However, I can't access my shared folders. After connecting to the VPN I can ping the server, but it is not shown in my networks. using \ip or \server-name doesn't work either, cannot be found. I checked ipconfig and this is what I found regarding the VPN: DNS-Suffix: Description: test Physical Adress: DHCP activated: No Auto-Config: Yes IPv4-Adress: 192.168.2.114 Sub: 255.255.255.255 Standard-gateway: DNS-Server: 192.168.0.1 NetBIOS: activated To clarify my IP-situation: server is connected to router with 192.168.0.x, the test-client is in an external network connected to a router with 192.168.1.x, server-client connection is using static ips with 192.168.2.x Can anyone help me with this one? The VPN should be ok since I am able to establish remote access.

  Read the article

• Internet connection sharing: Ubuntu 9.10 Server on Windows 7 and VMWare

  - by avesse

  I'm trying to get Internet Connection Sharing (ICS) working between my Windows 7 RTM host and a Ubuntu 9.10 Server running on VMWare Workstation 6.5, but I have not been able to get it right. Here's what I have done: Configured VMWare to use Host Only networking (I tried NAT as well). Enabled ICS on my host's network connection, allowing VMnet1. After enabling it, Windows informed me that its VMnet1 IP has changed to 192.168.137.1. So in VMWare's Virtual Network Editor I configured VMnet1: Subnet 192.168.137.0 Mask 255.255.255.0 I did the same for DHCP. For NAT i set 192.168.137.1 as Gateway. I cannot ping any sites or get access through apt-get/aptitude install/update, although domains do get resolved to IPs. I have also tried using a static IP in Ubuntu. I don't know if it makes a difference, but my external IP is locked to my host's MAC address.

  Read the article

• why would you create two different subnets on the same physical network?

  - by xirtyllo

  I'm working at a messy location, one of the strange (for me) things is that on the same physical network there are two different subnets. Specifically some computers will have 10.0.0.0/24 and some others will have 172.16.0.0/24. There is only one DHCP server, which gives IPs on the 10.0.0.0/24 range, and there are two internet gateways, one with IP 172.16.0.1 and one with IP 10.0.0.1 . To give an example, I can easily swap one PC from one subnet to the other just by changing its IP and gateway settings. I am trying to imagine why they created the network this way, and which may be the possible advantages and/or drawbacks of having two different subnets on the same physical network. Any thoughts?

  Read the article

• Can I log into a Domain account without pointing DNS to the domain controller?

  - by user72593

  My situation is as follows: I have a Windows 2003 Domain Controller which is also my DNS server. I have 10 Windows XP Pro PC's which all login to domain accounts. I am about the forward my DNS requests to OPENDNS so I can regulate web access but I have (2) PC's that I would like to keep unregulated. I manually changed their DNS server IP to (8.8.8.8) which worked but that caused my login to fail (by creating a 3 minute delay before it would let me get to the desktop) when I change the DNS IP back to the IP of the Domain Controller, everything works smoothly. Question is, how can I continue to login to the domain but have a different DNS path...is this possible ?

  Read the article

• Network Configuration

  - by Dario

  Hello, This is my situation: Router A: IP 192.168.1.1 Mask 192.168.1.0/24 - Connected to the internet. Server: - Interface eth0: inet addr:10.1.1.125 Mask:255.255.255.0 (connected to router B) - Interface ra0: inet addr:192.168.1.125 Mask:255.255.255.0 (connected to router A) Router B: IP 10.1.1.254 Mask 10.1.1.0/24 - Connected to Server's eth0 Computer: connected to Router B via WiFi connection. I configured a static route on Router B that use as default gateway 192.168.1.125 and i can ping that ip from computer. The problem is: how i can connect to the internet ? In other words, traffic coming from Server eth0 should use ra0 as gateway. Any suggestion ? Thank you

  Read the article

• How to legitimately work around ISP rate limits

  - by Derek Ting

  A lot of ISP rate limit the amount of e-mails that is sent from a particular IP address. What is the proper way to get around that rate limit? Our company has an iPhone application that sends many e-mails because of our large user base and many e-mails go to different ISPs that rate limit the number of messages coming from a specific IP. We do not send spam and we are a legitimate business. However, is there a better way to resolve this limitation rather than just getting a ton of IP addresses? Ideally, I wouldn't want to rely on a third party service to send mail. However, if its the only possible solution, we would consider.

  Read the article

• Cisco ASA - Enable communication between same security level

  - by Conor

  I have recently inherited a network with a Cisco ASA (running version 8.2). I am trying to configure it to allow communication between two interfaces configured with the same security level (DMZ-DMZ) "same-security-traffic permit inter-interface" has been set, but hosts are unable to communicate between the interfaces. I am assuming that some NAT settings are causing my issue. Below is my running config: ASA Version 8.2(3) ! hostname asa enable password XXXXXXXX encrypted passwd XXXXXXXX encrypted names ! interface Ethernet0/0 switchport access vlan 400 ! interface Ethernet0/1 switchport access vlan 400 ! interface Ethernet0/2 switchport access vlan 420 ! interface Ethernet0/3 switchport access vlan 420 ! interface Ethernet0/4 switchport access vlan 450 ! interface Ethernet0/5 switchport access vlan 450 ! interface Ethernet0/6 switchport access vlan 500 ! interface Ethernet0/7 switchport access vlan 500 ! interface Vlan400 nameif outside security-level 0 ip address XX.XX.XX.10 255.255.255.248 ! interface Vlan420 nameif public security-level 20 ip address 192.168.20.1 255.255.255.0 ! interface Vlan450 nameif dmz security-level 50 ip address 192.168.10.1 255.255.255.0 ! interface Vlan500 nameif inside security-level 100 ip address 192.168.0.1 255.255.255.0 ! ftp mode passive clock timezone JST 9 same-security-traffic permit inter-interface same-security-traffic permit intra-interface object-group network DM_INLINE_NETWORK_1 network-object host XX.XX.XX.11 network-object host XX.XX.XX.13 object-group service ssh_2220 tcp port-object eq 2220 object-group service ssh_2251 tcp port-object eq 2251 object-group service ssh_2229 tcp port-object eq 2229 object-group service ssh_2210 tcp port-object eq 2210 object-group service DM_INLINE_TCP_1 tcp group-object ssh_2210 group-object ssh_2220 object-group service zabbix tcp port-object range 10050 10051 object-group service DM_INLINE_TCP_2 tcp port-object eq www group-object zabbix object-group protocol TCPUDP protocol-object udp protocol-object tcp object-group service http_8029 tcp port-object eq 8029 object-group network DM_INLINE_NETWORK_2 network-object host 192.168.20.10 network-object host 192.168.20.30 network-object host 192.168.20.60 object-group service imaps_993 tcp description Secure IMAP port-object eq 993 object-group service public_wifi_group description Service allowed on the Public Wifi Group. Allows Web and Email. service-object tcp-udp eq domain service-object tcp-udp eq www service-object tcp eq https service-object tcp-udp eq 993 service-object tcp eq imap4 service-object tcp eq 587 service-object tcp eq pop3 service-object tcp eq smtp access-list outside_access_in remark http traffic from outside access-list outside_access_in extended permit tcp any object-group DM_INLINE_NETWORK_1 eq www access-list outside_access_in remark ssh from outside to web1 access-list outside_access_in extended permit tcp any host XX.XX.XX.11 object-group ssh_2251 access-list outside_access_in remark ssh from outside to penguin access-list outside_access_in extended permit tcp any host XX.XX.XX.10 object-group ssh_2229 access-list outside_access_in remark http from outside to penguin access-list outside_access_in extended permit tcp any host XX.XX.XX.10 object-group http_8029 access-list outside_access_in remark ssh from outside to internal hosts access-list outside_access_in extended permit tcp any host XX.XX.XX.13 object-group DM_INLINE_TCP_1 access-list outside_access_in remark dns service to internal host access-list outside_access_in extended permit object-group TCPUDP any host XX.XX.XX.13 eq domain access-list dmz_access_in extended permit ip 192.168.10.0 255.255.255.0 any access-list dmz_access_in extended permit tcp any host 192.168.10.29 object-group DM_INLINE_TCP_2 access-list public_access_in remark Web access to DMZ websites access-list public_access_in extended permit object-group TCPUDP any object-group DM_INLINE_NETWORK_2 eq www access-list public_access_in remark General web access. (HTTP, DNS & ICMP and Email) access-list public_access_in extended permit object-group public_wifi_group any any pager lines 24 logging enable logging asdm informational mtu outside 1500 mtu public 1500 mtu dmz 1500 mtu inside 1500 no failover icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 60 global (outside) 1 interface global (dmz) 2 interface nat (public) 1 0.0.0.0 0.0.0.0 nat (dmz) 1 0.0.0.0 0.0.0.0 nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface 2229 192.168.0.29 2229 netmask 255.255.255.255 static (inside,outside) tcp interface 8029 192.168.0.29 www netmask 255.255.255.255 static (dmz,outside) XX.XX.XX.13 192.168.10.10 netmask 255.255.255.255 dns static (dmz,outside) XX.XX.XX.11 192.168.10.30 netmask 255.255.255.255 dns static (dmz,inside) 192.168.0.29 192.168.10.29 netmask 255.255.255.255 static (dmz,public) 192.168.20.30 192.168.10.30 netmask 255.255.255.255 dns static (dmz,public) 192.168.20.10 192.168.10.10 netmask 255.255.255.255 dns static (inside,dmz) 192.168.10.0 192.168.0.0 netmask 255.255.255.0 dns access-group outside_access_in in interface outside access-group public_access_in in interface public access-group dmz_access_in in interface dmz route outside 0.0.0.0 0.0.0.0 XX.XX.XX.9 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy http server enable http 192.168.0.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 telnet timeout 5 ssh 192.168.0.0 255.255.255.0 inside ssh timeout 20 console timeout 0 dhcpd dns 61.122.112.97 61.122.112.1 dhcpd auto_config outside ! dhcpd address 192.168.20.200-192.168.20.254 public dhcpd enable public ! dhcpd address 192.168.0.200-192.168.0.254 inside dhcpd enable inside ! threat-detection basic-threat threat-detection statistics host threat-detection statistics access-list no threat-detection statistics tcp-intercept ntp server 130.54.208.201 source public webvpn ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum client auto message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect ip-options inspect netbios inspect rsh inspect rtsp inspect skinny inspect esmtp inspect sqlnet inspect sunrpc inspect tftp inspect sip inspect xdmcp !

  Read the article

• Apache localhost problem

  - by hart1994

  I have set up Apache on my Windows 7 PC. Now I have it working fine on the PC, by going to localhost or the IP (192.168.1.71). However when I go to my Mac I try to connect to it via its IP and it doesn't connect. I have also tried this on another computer. Oops! Google Chrome could not connect to 192.168.1.71 Now is there something wrong with the code in the Apache httpd file? EDIT: I have also tried to ping the IP address and it works fine.

  Read the article

• OpenVPN Push DNS Not Working Correctly On Windows

  - by woodsbw

  I currently have OpenVPN server setup on an Ubuntu machine, as well as DNSMasq. I am wanting to push DNS to the client (road warrior setup.) I had the push "dhcp-option DNS x.x.x.x" where x.x.x.x was an open OpenDNS server, for testing, and everything was working when I connected from my Windows client But now that I have DNSMasq setup, and I changed the "dhcp-option DNS x.x.x.x" to the DNSMasq server, but when they client connects it still receives the old, OpenDNS DNS server IP. I'm at a bit of a loss here, I have tried flushing DNS on the client, rebooting the server, and I even grep'd the entire server to see if the OpenDNS IP was in some other config I was missing...it wasn't. One other note, when connect to the VPN and explicitly run nslookup against against the DNSMasq IP, the addresses resolve correctly, so it isn't a DNSMasq issue.

  Read the article

• Net Screen manager setup

  - by Codezy

  I'm having an issue with our NSMExpress box. I'm trying to manage all our devices, range from ns5gt to ssg320m, and some of those devices have addresses assigned by dhcp from the ISP (like pppoe or dsl). The addresses are actually static but we have the register the MAC address in order to get this address. I can actually add the device in NSM except the IP that's on the untrust side isn't imported in as it's dynamic. Because of this I cannot change many options that pertian to the untrust interface as there is no IP. I've talked to JTAC on this and they didn't know if there was a way to do this or not but then they stated that Tim Hortons does this so I'm confused on how to get this working. Maybe i'm just missing something as I imagine that other people must be doing this as well. Any assistance is appreciated! Furthermore when I import a device this is the message I get: Warnings: Interface ethernet0/0 is a pppoe/dhcp/pppoa client and its ip is NOT IMPORTED because it may be dynamic.

  Read the article

• Calculate data transferred in a local LAN

  - by ramdaz

  How do you calculate the data flown between a computer and the gateway computer. I have a Linux router/gateway running IP Tables which routes internet traffic in a LAN. I have individual users with IP/MAC Address mapped who access Interet through the gateway computer. I would like to find out the traffic utilized by individual users. Is it possible for us to find out what kind of traffic was HTTP, SMTP, FTP etc. Is it also possible to pool the information on hourly basis, and get specific info so that I can store information in a database? I have heard of IP Accounting? Is that the right way

  Read the article

• Security question pertaining web application deployment

  - by orokusaki

  I am about to deploy a web application (in a couple months) with the following set-up (perhaps anyways): Ubuntu Lucid Lynx with: IP Tables firewall (white-list style with only 3 ports open) Custom SSH port (like 31847 or something) No "root" SSH access Long, random username (not just "admin" or something) with a long password (65 chars) PostgreSQL which only listens to localhost 256 bit SSL Cert Reverse proxy from NGINX to my application server (UWSGI) Assume that my colo is secure (Physical access isn't my concern for the time being) Application-level security (SQL injection, XSS, Directory Traversal, CSRF, etc) Perhaps IP masquerading (but I don't really understand this yet) Does this sound like a secure setup? I hear about people's web apps getting hacked all the time, and part of me thinks, "maybe they're just neglecting something", but the other part of me thinks, "maybe there's nothing you can do to protect your server, and those things are just measures to make it a little harder for script kiddies to get in". If I told you all of this, gave you my IP address, and told you what ports were available, would it be possible for you to get in (assuming you have a penetration testing tool), or is this really protected well.

  Read the article

• Microsoft ISA 2004 - Failed Connection Attempt

  - by Arief

  I have an issue where users with Android tablet cannot download apps through ISA 2004. This is what I get from the ISA 2004 logging: I did try to add the source ip address and the destination ip address in All for All Modified rule. However, it does not fix that problem. I also use GFI Web Monitoring. I did add the 151.101.13.80 ip address into the Whitelist, and no luck. What Failed Connection Attempt exactly is? How to overcome this. The Android tablet is throwing an error 495, could not be downloaded. Thanks everyone.

  Read the article

• Sonicwall settings for Polycom TFTP

  - by Michael Glenn

  I'm switching our VoIP phones (Polycom 301s and 501s) to our data network. They were previously segmented to their own network. This means disabling the DHCP on the Trixbox (Asterisk) server and configuring the Sonicwall TZ 210 DHCP to indicate that Trixbox is the TFTP server. The Polycom phones are stating "could not contact boot server". All phones are configured to TFTP and were confirmed working when previously using the Trixbox server for DHCP. Trixbox DHCP is now turned off. I've configured options 66(as String), 128(as IP) and 150(as IP) in DHCP and added them to a TFTP Option Group. I've enabled "Allow BOOTP Clients to use Range" for the Dynamic IP range and assigned the Option Group TFTP as the DHCP Generic Option Group. Any idea what I'm missing? Is there a separate tool to inspect the DHCP response to compare Trixbox to the Sonicwall?

  Read the article

• Setting up a proxy for FTP - Windows

  - by RadiantHex

  Hi folks, I have 2 windows machines and a server. 1 is my laptop, the other is a workstation that the IP of which is white-listed on the server. The laptop has a dynamic IP, so the IP cannot be white-listed. I would like to be able to perform FTP transfers from my laptop to the server, while using the workstation as a proxy. Both machines are using Windows 7. Is this possible? Help would be amazing!

  Read the article

• Error with FTP since binding via httpcfg

  - by Linda

  I was in a similar posistion to this question and bound two IP addresses using httpcfg. Since doing this ftp does not seem to be working on IIS6 in Windows Server 2003. Any ideas what could be wrong? The command I ran was: httpcfg set iplisten -i xxx.xxx.x.x I get the following when I try to conenct via Filezilla: Error: Connection timed out Error: Failed to retrieve directory listing The log file is returning the following: #Software: Microsoft Internet Information Services 6.0 #Version: 1.0 #Date: 2009-08-17 13:54:05 #Fields: date time c-ip cs-username cs-method cs-uri-stem sc-status sc-win32-status 2009-08-17 13:54:05 91.85.70.17 Client [1]USER Client 331 0 2009-08-17 13:54:05 91.85.70.17 Client [1]PASS - 230 0 In the ftp site settings I have the site pointing to the IP address used using httpcfg and the port set to 21. Update: I can see a directory listing if I connect via the inbuilt commandline ftp client in wondows vista. If I try to connect via a windows explorer I start in the incorrect folder and no files are listed just directories.

  Read the article

• How does bridged networking work?

  - by agz

  How does bridged networking work? I have looked through the virtualbox manuals but nothing extremely technical came up (It was just a generic gloss over of the topic) How does it assign a different ip to the virtual machine but uses the same network card? Why does this different ip (I found using ip addr under linux) not show up under the "attached devices section" of my router but I can port forward to it? How come if I connect to a password protected wifi network, it does not require me to enter my password? Is this multihoming?

  Read the article

< Previous Page | 199 200 201 202 203 204 205 206 207 208 209 210  | Next Page >