Search Results

Search found 5084 results on 204 pages for 'policy routing'.

Page 203/204 | < Previous Page | 199 200 201 202 203 204  | Next Page >

  • Inbound SIP calls through Cisco 881 NAT hang up after a few seconds

    - by MasterRoot24
    I've recently moved to a Cisco 881 router for my WAN link. I was previously using a Cisco Linksys WAG320N as my modem/router/WiFi AP/NAT firewall. The WAG320N is now running in bridged mode, so it's simply acting as a modem with one of it's LAN ports connected to FE4 WAN on my Cisco 881. The Cisco 881 get's a DHCP provided IP from my ISP. My LAN is part of default Vlan 1 (192.168.1.0/24). General internet connectivity is working great, I've managed to setup static NAT rules for my HTTP/HTTPS/SMTP/etc. services which are running on my LAN. I don't know whether it's worth mentioning that I've opted to use NVI NAT (ip nat enable as opposed to the traditional ip nat outside/ip nat inside) setup. My reason for this is that NVI allows NAT loopback from my LAN to the WAN IP and back in to the necessary server on the LAN. I run an Asterisk 1.8 PBX on my LAN, which connects to a SIP provider on the internet. Both inbound and outbound calls through the old setup (WAG320N providing routing/NAT) worked fine. However, since moving to the Cisco 881, inbound calls drop after around 10 seconds, whereas outbound calls work fine. The following message is logged on my Asterisk PBX: [Dec 9 15:27:45] WARNING[27734]: chan_sip.c:3641 retrans_pkt: Retransmission timeout reached on transmission [email protected] for seqno 1 (Critical Response) -- See https://wiki.asterisk.org/wiki/display/AST/SIP+Retransmissions Packet timed out after 6528ms with no response [Dec 9 15:27:45] WARNING[27734]: chan_sip.c:3670 retrans_pkt: Hanging up call [email protected] - no reply to our critical packet (see https://wiki.asterisk.org/wiki/display/AST/SIP+Retransmissions). (I know that this is quite a common issue - I've spend the best part of 2 days solid on this, trawling Google.) I've done as I am told and checked https://wiki.asterisk.org/wiki/display/AST/SIP+Retransmissions. Referring to the section "Other SIP requests" in the page linked above, I believe that the hangup to be caused by the ACK from my SIP provider not being passed back through NAT to Asterisk on my PBX. I tried to ascertain this by dumping the packets on my WAN interface on the 881. I managed to obtain a PCAP dump of packets in/out of my WAN interface. Here's an example of an ACK being reveived by the router from my provider: 689 21.219999 193.x.x.x 188.x.x.x SIP 502 Request: ACK sip:[email protected] | However a SIP trace on the Asterisk server show's that there are no ACK's received in response to the 200 OK from my PBX: http://pastebin.com/wwHpLPPz In the past, I have been strongly advised to disable any sort of SIP ALGs on routers and/or firewalls and the many posts regarding this issue on the internet seem to support this. However, I believe on Cisco IOS, the config command to disable SIP ALG is no ip nat service sip udp port 5060 however, this doesn't appear to help the situation. To confirm that config setting is set: Router1#show running-config | include sip no ip nat service sip udp port 5060 Another interesting twist: for a short period of time, I tried another provider. Luckily, my trial account with them is still available, so I reverted my Asterisk config back to the revision before I integrated with my current provider. I then dialled in to the DDI associated with the trial trunk and the call didn't get hung up and I didn't get the error above! To me, this points at the provider, however I know, like all providers do, will say "There's no issues with our SIP proxies - it's your firewall." I'm tempted to agree with this, as this issue was not apparent with the old WAG320N router when it was doing the NAT'ing. I'm sure you'll want to see my running-config too: ! ! Last configuration change at 15:55:07 UTC Sun Dec 9 2012 by xxx version 15.2 no service pad service tcp-keepalives-in service tcp-keepalives-out service timestamps debug datetime msec localtime show-timezone service timestamps log datetime msec localtime show-timezone no service password-encryption service sequence-numbers ! hostname Router1 ! boot-start-marker boot-end-marker ! ! security authentication failure rate 10 log security passwords min-length 6 logging buffered 4096 logging console critical enable secret 4 xxx ! aaa new-model ! ! aaa authentication login local_auth local ! ! ! ! ! aaa session-id common ! memory-size iomem 10 ! crypto pki trustpoint TP-self-signed-xxx enrollment selfsigned subject-name cn=IOS-Self-Signed-Certificate-xxx revocation-check none rsakeypair TP-self-signed-xxx ! ! crypto pki certificate chain TP-self-signed-xxx certificate self-signed 01 quit no ip source-route no ip gratuitous-arps ip auth-proxy max-login-attempts 5 ip admission max-login-attempts 5 ! ! ! ! ! no ip bootp server ip domain name dmz.merlin.local ip domain list dmz.merlin.local ip domain list merlin.local ip name-server x.x.x.x ip inspect audit-trail ip inspect udp idle-time 1800 ip inspect dns-timeout 7 ip inspect tcp idle-time 14400 ip inspect name autosec_inspect ftp timeout 3600 ip inspect name autosec_inspect http timeout 3600 ip inspect name autosec_inspect rcmd timeout 3600 ip inspect name autosec_inspect realaudio timeout 3600 ip inspect name autosec_inspect smtp timeout 3600 ip inspect name autosec_inspect tftp timeout 30 ip inspect name autosec_inspect udp timeout 15 ip inspect name autosec_inspect tcp timeout 3600 ip cef login block-for 3 attempts 3 within 3 no ipv6 cef ! ! multilink bundle-name authenticated license udi pid CISCO881-SEC-K9 sn ! ! username xxx privilege 15 secret 4 xxx username xxx secret 4 xxx ! ! ! ! ! ip ssh time-out 60 ! ! ! ! ! ! ! ! ! interface FastEthernet0 no ip address ! interface FastEthernet1 no ip address ! interface FastEthernet2 no ip address ! interface FastEthernet3 switchport access vlan 2 no ip address ! interface FastEthernet4 ip address dhcp no ip redirects no ip unreachables no ip proxy-arp ip nat enable duplex auto speed auto ! interface Vlan1 ip address 192.168.1.1 255.255.255.0 no ip redirects no ip unreachables no ip proxy-arp ip nat enable ! interface Vlan2 ip address 192.168.0.2 255.255.255.0 ! ip forward-protocol nd ip http server ip http access-class 1 ip http authentication local ip http secure-server ip http timeout-policy idle 60 life 86400 requests 10000 ! ! no ip nat service sip udp port 5060 ip nat source list 1 interface FastEthernet4 overload ip nat source static tcp x.x.x.x 80 interface FastEthernet4 80 ip nat source static tcp x.x.x.x 443 interface FastEthernet4 443 ip nat source static tcp x.x.x.x 25 interface FastEthernet4 25 ip nat source static tcp x.x.x.x 587 interface FastEthernet4 587 ip nat source static tcp x.x.x.x 143 interface FastEthernet4 143 ip nat source static tcp x.x.x.x 993 interface FastEthernet4 993 ip nat source static tcp x.x.x.x 1723 interface FastEthernet4 1723 ! ! logging trap debugging logging facility local2 access-list 1 permit 192.168.1.0 0.0.0.255 access-list 1 permit 192.168.0.0 0.0.0.255 no cdp run ! ! ! ! control-plane ! ! banner motd Authorized Access only ! line con 0 login authentication local_auth length 0 transport output all line aux 0 exec-timeout 15 0 login authentication local_auth transport output all line vty 0 1 access-class 1 in logging synchronous login authentication local_auth length 0 transport preferred none transport input telnet transport output all line vty 2 4 access-class 1 in login authentication local_auth length 0 transport input ssh transport output all ! ! end ...and, if it's of any use, here's my Asterisk SIP config: [general] context=default ; Default context for calls allowoverlap=no ; Disable overlap dialing support. (Default is yes) udpbindaddr=0.0.0.0 ; IP address to bind UDP listen socket to (0.0.0.0 binds to all) ; Optionally add a port number, 192.168.1.1:5062 (default is port 5060) tcpenable=no ; Enable server for incoming TCP connections (default is no) tcpbindaddr=0.0.0.0 ; IP address for TCP server to bind to (0.0.0.0 binds to all interfaces) ; Optionally add a port number, 192.168.1.1:5062 (default is port 5060) srvlookup=yes ; Enable DNS SRV lookups on outbound calls ; Note: Asterisk only uses the first host ; in SRV records ; Disabling DNS SRV lookups disables the ; ability to place SIP calls based on domain ; names to some other SIP users on the Internet ; Specifying a port in a SIP peer definition or ; when dialing outbound calls will supress SRV ; lookups for that peer or call. directmedia=no ; Don't allow direct RTP media between extensions (doesn't work through NAT) externhost=<MY DYNDNS HOSTNAME> ; Our external hostname to resolve to IP and be used in NAT'ed packets localnet=192.168.1.0/24 ; Define our local network so we know which packets need NAT'ing qualify=yes ; Qualify peers by default dtmfmode=rfc2833 ; Set the default DTMF mode disallow=all ; Disallow all codecs by default allow=ulaw ; Allow G.711 u-law allow=alaw ; Allow G.711 a-law ; ---------------------- ; SIP Trunk Registration ; ---------------------- ; Orbtalk register => <MY SIP PROVIDER USER NAME>:[email protected]/<MY DDI> ; Main Orbtalk number ; ---------- ; Trunks ; ---------- [orbtalk] ; Main Orbtalk trunk type=peer insecure=invite host=sipgw3.orbtalk.co.uk nat=yes username=<MY SIP PROVIDER USER NAME> defaultuser=<MY SIP PROVIDER USER NAME> fromuser=<MY SIP PROVIDER USER NAME> secret=xxx context=inbound I really don't know where to go with this. If anyone can help me find out why these calls are being dropped off, I'd be grateful if you could chime in! Please let me know if any further info is required.

    Read the article

  • Async ignored on AJAX requests on Nginx server

    - by eComEvo
    Despite sending an async request to the server over AJAX, the server will not respond until the previous unrelated request has finished. The following code is only broken in this way on Nginx, but runs perfectly on Apache. This call will start a background process and it waits for it to complete so it can display the final result. $.ajax({ type: 'GET', async: true, url: $(this).data('route'), data: $('input[name=data]').val(), dataType: 'json', success: function (data) { /* do stuff */} error: function (data) { /* handle errors */} }); The below is called after the above, which on Apache requires 100ms to execute and repeats itself, showing progress for data being written in the background: checkStatusInterval = setInterval(function () { $.ajax({ type: 'GET', async: false, cache: false, url: '/process-status?process=' + currentElement.attr('id'), dataType: 'json', success: function (data) { /* update progress bar and status message */ } }); }, 1000); Unfortunately, when this script is run from nginx, the above progress request never even finishes a single request until the first AJAX request that sent the data is done. If I change the async to TRUE in the above, it executes one every interval, but none of them complete until that very first AJAX request finishes. Here is the main nginx conf file: #user nobody; worker_processes 1; #error_log logs/error.log; #error_log logs/error.log notice; #error_log logs/error.log info; #pid logs/nginx.pid; events { worker_connections 1024; } http { include mime.types; default_type application/octet-stream; server_names_hash_bucket_size 64; # configure temporary paths # nginx is started with param -p, setting nginx path to serverpack installdir fastcgi_temp_path temp/fastcgi; uwsgi_temp_path temp/uwsgi; scgi_temp_path temp/scgi; client_body_temp_path temp/client-body 1 2; proxy_temp_path temp/proxy; log_format main '$remote_addr - $remote_user [$time_local] "$request" ' '$status $body_bytes_sent "$http_referer" ' '"$http_user_agent" "$http_x_forwarded_for"'; #access_log logs/access.log main; # Sendfile copies data between one FD and other from within the kernel. # More efficient than read() + write(), since the requires transferring data to and from the user space. sendfile on; # Tcp_nopush causes nginx to attempt to send its HTTP response head in one packet, # instead of using partial frames. This is useful for prepending headers before calling sendfile, # or for throughput optimization. tcp_nopush on; # don't buffer data-sends (disable Nagle algorithm). Good for sending frequent small bursts of data in real time. tcp_nodelay on; types_hash_max_size 2048; # Timeout for keep-alive connections. Server will close connections after this time. keepalive_timeout 90; # Number of requests a client can make over the keep-alive connection. This is set high for testing. keepalive_requests 100000; # allow the server to close the connection after a client stops responding. Frees up socket-associated memory. reset_timedout_connection on; # send the client a "request timed out" if the body is not loaded by this time. Default 60. client_header_timeout 20; client_body_timeout 60; # If the client stops reading data, free up the stale client connection after this much time. Default 60. send_timeout 60; # Size Limits client_body_buffer_size 64k; client_header_buffer_size 4k; client_max_body_size 8M; # FastCGI fastcgi_connect_timeout 60; fastcgi_send_timeout 120; fastcgi_read_timeout 300; # default: 60 secs; when step debugging with XDEBUG, you need to increase this value fastcgi_buffer_size 64k; fastcgi_buffers 4 64k; fastcgi_busy_buffers_size 128k; fastcgi_temp_file_write_size 128k; # Caches information about open FDs, freqently accessed files. open_file_cache max=200000 inactive=20s; open_file_cache_valid 30s; open_file_cache_min_uses 2; open_file_cache_errors on; # Turn on gzip output compression to save bandwidth. # http://wiki.nginx.org/HttpGzipModule gzip on; gzip_disable "MSIE [1-6]\.(?!.*SV1)"; gzip_http_version 1.1; gzip_vary on; gzip_proxied any; #gzip_proxied expired no-cache no-store private auth; gzip_comp_level 6; gzip_buffers 16 8k; gzip_types text/plain text/css application/json application/x-javascript text/xml application/xml application/xml+rss text/javascript application/javascript; # show all files and folders autoindex on; server { # access from localhost only listen 127.0.0.1:80; server_name localhost; root www; # the following default "catch-all" configuration, allows access to the server from outside. # please ensure your firewall allows access to tcp/port 80. check your "skype" config. # listen 80; # server_name _; log_not_found off; charset utf-8; access_log logs/access.log main; # handle files in the root path /www location / { index index.php index.html index.htm; } #error_page 404 /404.html; # redirect server error pages to the static page /50x.html # error_page 500 502 503 504 /50x.html; location = /50x.html { root www; } # pass the PHP scripts to FastCGI server listening on 127.0.0.1:9100 # location ~ \.php$ { try_files $uri =404; fastcgi_pass 127.0.0.1:9100; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; include fastcgi_params; } # add expire headers location ~* ^.+.(gif|ico|jpg|jpeg|png|flv|swf|pdf|mp3|mp4|xml|txt|js|css)$ { expires 30d; } # deny access to .htaccess files (if Apache's document root concurs with nginx's one) # deny access to git & svn repositories location ~ /(\.ht|\.git|\.svn) { deny all; } } # include config files of "enabled" domains include domains-enabled/*.conf; } Here is the enabled domain conf file: access_log off; access_log C:/server/www/test.dev/logs/access.log; error_log C:/server/www/test.dev/logs/error.log; # HTTP Server server { listen 127.0.0.1:80; server_name test.dev; root C:/server/www/test.dev/public; index index.php; rewrite_log on; default_type application/octet-stream; #include /etc/nginx/mime.types; # Include common configurations. include domains-common/location.conf; } # HTTPS server server { listen 443 ssl; server_name test.dev; root C:/server/www/test.dev/public; index index.php; rewrite_log on; default_type application/octet-stream; #include /etc/nginx/mime.types; # Include common configurations. include domains-common/location.conf; include domains-common/ssl.conf; } Contents of ssl.conf: # OpenSSL for HTTPS connections. ssl on; ssl_certificate C:/server/bin/openssl/certs/cert.pem; ssl_certificate_key C:/server/bin/openssl/certs/cert.key; ssl_session_timeout 5m; ssl_protocols SSLv3 TLSv1 TLSv1.1 TLSv1.2; ssl_ciphers HIGH:!aNULL:!MD5; ssl_prefer_server_ciphers on; # Pass the PHP scripts to FastCGI server listening on 127.0.0.1:9100 location ~ \.php$ { try_files $uri =404; fastcgi_param HTTPS on; fastcgi_pass 127.0.0.1:9100; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; include fastcgi_params; } Contents of location.conf: # Remove trailing slash to please Laravel routing system. if (!-d $request_filename) { rewrite ^/(.+)/$ /$1 permanent; } location / { try_files $uri $uri/ /index.php?$query_string; } # We don't need .ht files with nginx. location ~ /(\.ht|\.git|\.svn) { deny all; } # Added cache headers for images. location ~* \.(png|jpg|jpeg|gif)$ { expires 30d; log_not_found off; } # Only 3 hours on CSS/JS to allow me to roll out fixes during early weeks. location ~* \.(js|css)$ { expires 3h; log_not_found off; } # Add expire headers. location ~* ^.+.(gif|ico|jpg|jpeg|png|flv|swf|pdf|mp3|mp4|xml|txt)$ { expires 30d; } # Pass the PHP scripts to FastCGI server listening on 127.0.0.1:9100 location ~ \.php$ { try_files $uri /index.php =404; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; include fastcgi_params; fastcgi_pass 127.0.0.1:9100; } Any ideas where this is going wrong?

    Read the article

  • Something very strange with network

    - by Rodnower
    Hello, I have Windows 7 and I have very strange thing with my network. Some time I was connected through wireless router and my IP was 192.168.2.103, router's IP was 192.168.2.1 and some other IP was 192.168.2.100. The last I get from page "active DHCP clients" of web interface of the router and from "wireless clients" I may to see that 192.168.2.100 not (!) belong to my MAC address. Router build by EDimax. So after that I disabled wireless function of the router and restarted it. In this time I had not ping to 192.168.2.1. Also I had not any other connection, not wireless nor cable, but (!) I still had ping to 192.168.2.100 and I not understand what this voodoo is... C:\Users\Andrey>ping 192.168.2.100 Pinging 192.168.2.100 with 32 bytes of data: Reply from 192.168.2.100: bytes=32 time<1ms TTL=128 Reply from 192.168.2.100: bytes=32 time<1ms TTL=128 Reply from 192.168.2.100: bytes=32 time<1ms TTL=128 Reply from 192.168.2.100: bytes=32 time<1ms TTL=128 Ping statistics for 192.168.2.100: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms This is what I had: C:\Users\Andrey>ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : Andrey-PC Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No Wireless LAN adapter Wireless Network Connection 3: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Microsoft Virtual WiFi Miniport Adapter #2 Physical Address. . . . . . . . . : 06-1D-7D-40-61-EB DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Wireless LAN adapter Wireless Network Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Gigabyte GN-WS50G (mini) PCI-E WLAN Card Physical Address. . . . . . . . . : 00-1D-7D-40-61-EB DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Ethernet adapter Local Area Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Marvell Yukon 88E8055 PCI-E Gigabit Ethernet Controller Physical Address. . . . . . . . . : 00-1B-24-B6-09-91 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes C:\Users\Andrey>arp -a -v Interface: 127.0.0.1 --- 0x1 Internet Address Physical Address Type 224.0.0.22 static 239.255.255.250 static Interface: 0.0.0.0 --- 0xffffffff Internet Address Physical Address Type 192.168.2.1 00-0e-2e-d2-8c-af invalid 192.168.2.255 ff-ff-ff-ff-ff-ff static 224.0.0.22 01-00-5e-00-00-16 static 224.0.0.252 01-00-5e-00-00-fc static 239.255.255.250 01-00-5e-7f-ff-fa static 255.255.255.255 ff-ff-ff-ff-ff-ff static Interface: 0.0.0.0 --- 0xffffffff Internet Address Physical Address Type 192.168.2.1 00-0e-2e-ff-f1-f6 dynamic 192.168.2.101 00-27-19-bc-8b-9c dynamic 192.168.2.102 00-16-e6-6c-ae-d4 dynamic 192.168.2.255 ff-ff-ff-ff-ff-ff static 224.0.0.22 01-00-5e-00-00-16 static 224.0.0.252 01-00-5e-00-00-fc static 239.255.255.250 01-00-5e-7f-ff-fa static 255.255.255.255 ff-ff-ff-ff-ff-ff static Interface: 0.0.0.0 --- 0xffffffff Internet Address Physical Address Type 224.0.0.22 01-00-5e-00-00-16 static 255.255.255.255 ff-ff-ff-ff-ff-ff static C:\Users\Andrey>route print =========================================================================== Interface List 14...06 1d 7d 40 61 eb ......Microsoft Virtual WiFi Miniport Adapter #2 13...00 1d 7d 40 61 eb ......Gigabyte GN-WS50G (mini) PCI-E WLAN Card 11...00 1b 24 b6 09 91 ......Marvell Yukon 88E8055 PCI-E Gigabit Ethernet Controller 1...........................Software Loopback Interface 1 =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 =========================================================================== Persistent Routes: None IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 1 306 ::1/128 On-link 1 306 ff00::/8 On-link =========================================================================== Persistent Routes: None Only after reboot I lost ping to there: C:\Users\Andrey>ping 192.168.2.100 Pinging 192.168.2.100 with 32 bytes of data: PING: transmit failed. General failure. PING: transmit failed. General failure. PING: transmit failed. General failure. PING: transmit failed. General failure. Ping statistics for 192.168.2.100: Packets: Sent = 4, Received = 0, Lost = 4 (100% loss), So what this mysterious cache is? Thank you for ahead.

    Read the article

  • Unstable DNS with bind

    - by yasser abd
    we have a Centos machine called jupiter, on which I have installed bind9, On every other machine the DNS is set to be the IP address of jupiter (192.168.2.101), as you can see in the output of the following command in windows >ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : mypcs Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Broadcom NetXtreme 57xx Gigabit Controller Physical Address. . . . . . . . . : 00-1A-A0-AC-E4-CC DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::c16d:3ae4:5907:30c4%8(Preferred) IPv4 Address. . . . . . . . . . . : 192.168.2.98(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : Thursday, September 20, 2012 10:26:11 AM Lease Expires . . . . . . . . . . : Sunday, September 23, 2012 10:26:10 AM Default Gateway . . . . . . . . . : 192.168.2.1 DHCP Server . . . . . . . . . . . : 192.168.2.1 DHCPv6 IAID . . . . . . . . . . . : 201333408 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-16-3A-50-01-00-1A-A0-AC-E4-CC DNS Servers . . . . . . . . . . . : 192.168.2.101 192.168.2.1 192.168.2.1 NetBIOS over Tcpip. . . . . . . . : Enabled All machines can always nslookup one of the domain (mydomain.com) that is set in the jupiter's DNS server, you can see that in the output of nslookup on the same windows machine: >nslookup mydomain.com Server: UnKnown Address: 192.168.2.101 Name: mydomain.com Address: 192.168.2.100 The problem is, sometimes mydomain.com can not be pinged, here is the output of the ping on the same windows machine >ping mydomain.com Ping request could not find host mydomain.com. Please check the name and try again. This looks very random, and happens once in a while, so the machine can lookup the DNS records but can't ping it, nor can browse the website that is hosted on mydomain.com, which should resolve to 192.168.2.100 On a linux machine that has the same DNS settings, the output of dig command for mydomain is as follows: $ dig mydomain.com ; <<>> DiG 9.8.2rc1-RedHat-9.8.2-0.10.rc1.el6_3.2 <<>> mydomain.com ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 36090 ;; flags: qr aa rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 1, ADDITIONAL: 1 ;; QUESTION SECTION: ;mydomain.com. IN A ;; ANSWER SECTION: mydomain.com. 86400 IN A 192.168.2.100 ;; AUTHORITY SECTION: mydomain.com. 86400 IN NS jupiter. ;; ADDITIONAL SECTION: jupiter. 86400 IN A 192.168.2.101 ;; Query time: 1 msec ;; SERVER: 192.168.2.101#53(192.168.2.101) ;; WHEN: Thu Sep 20 16:32:14 2012 ;; MSG SIZE rcvd: 83 We've never had the same problem on MACs, they always resolve mydomain.com Here is how I have defined mydomain.com on Bind9's configs on Jupiter, notice that the name of the machine on 192.168.2.100 is venus, so I have this file: /var/named/named.venus: $TTL 1D @ IN SOA jupiter. admin.ourcompany.com. ( 2003052800 ; serial 86400 ; refresh 300 ; retry 604800 ; expire 3600 ; minimum ) @ IN NS jupiter. @ IN A 192.168.2.100 * IN A 192.168.2.100 /var/named/zones/named.venus.zone zone "mydomain.com" IN {type master;file "/var/named/named.venus";allow-update {none;};}; One thing to note is that I haven't defined reverse DNS lookups, only the forward DNS lookups are defined in Bind9 configs, not sure if that's relevant or not. So my question is, why is this being so unstable? what could be the cause?

    Read the article

  • How does Windows 7 DNS client work?

    - by Mark Allison
    I am using a local DHCP and DNS server on my home network on a linux machine. It is running CentOS 6.3 with dnsmasq 2.48. It's all working fine except for local DNS lookups for Windows machines only. I have a mix of Ubuntu, CentOS and Windows machines on the network, some virtual, some physical. I have a machine called boron and the domain is called localdomain If I ping boron from any linux machine, I get [root@lithium lists]# ping -c3 boron PING boron.localdomain (10.0.0.5) 56(84) bytes of data. 64 bytes from boron.localdomain (10.0.0.5): icmp_seq=1 ttl=64 time=0.740 ms 64 bytes from boron.localdomain (10.0.0.5): icmp_seq=2 ttl=64 time=0.478 ms 64 bytes from boron.localdomain (10.0.0.5): icmp_seq=3 ttl=64 time=0.458 ms --- boron.localdomain ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 2000ms rtt min/avg/max/mdev = 0.458/0.558/0.740/0.131 ms If I do it from my Windows 7 machine, I get: Ping request could not find host boron. Please check the name and try again. If I try ping boron.localdomain I get: Pinging boron.localdomain [67.215.65.132] with 32 bytes of data: Reply from 67.215.65.132: bytes=32 time=16ms TTL=57 Reply from 67.215.65.132: bytes=32 time=188ms TTL=57 Reply from 67.215.65.132: bytes=32 time=15ms TTL=57 Reply from 67.215.65.132: bytes=32 time=14ms TTL=57 Ping statistics for 67.215.65.132: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 14ms, Maximum = 188ms, Average = 58ms which is clearly wrong. Why is it going out to the internet? Why can't my windows machine resolve the boron hostname to a FQDN? My Windows machines and linux machines get their network config from DHCP. UPDATE If I do ipconfig /all in Windows, it looks as I would expect: Windows IP Configuration Host Name . . . . . . . . . . . . : lanthanum Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : .localdomain Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : .localdomain Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller Physical Address. . . . . . . . . : 50-E5-49-38-FC-A2 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 10.0.0.57(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : 23 August 2012 13:58:45 Lease Expires . . . . . . . . . . : 24 August 2012 07:58:48 Default Gateway . . . . . . . . . : 10.0.0.6 DHCP Server . . . . . . . . . . . : 10.0.0.6 DNS Servers . . . . . . . . . . . : 10.0.0.6 208.67.222.222 208.67.220.220 NetBIOS over Tcpip. . . . . . . . : Enabled When I do an nslookup I get: Server: carbon.localdomain Address: 10.0.0.6 *** carbon.localdomain can't find boron: Unspecified error However if I do ifconfig -a in Linux I get: [root@nitrogen ~]# ifconfig -a eth0 Link encap:Ethernet HWaddr 00:0C:29:AF:EC:2A inet addr:10.0.0.7 Bcast:10.0.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:187687 errors:0 dropped:0 overruns:0 frame:0 TX packets:5857 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:23910700 (22.8 MiB) TX bytes:712964 (696.2 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:329894 errors:0 dropped:0 overruns:0 frame:0 TX packets:329894 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:67153143 (64.0 MiB) TX bytes:67153143 (64.0 MiB) and nslookup: [root@nitrogen ~]# nslookup boron Server: 10.0.0.6 Address: 10.0.0.6#53 Name: boron Address: 10.0.0.5 Both machines are on the same network using the same DHCP server. UPDATE 2 I thought the issue was resolved but I am getting intermittent DNS resolving issues but only on my Windows 7 machine. All my linux boxes are fine. This is what happens when I ping and nslookup from Windows to a Windows 2008 Server: C:\Users\mark>nslookup magnesium Server: carbon.localdomain Address: 10.0.0.6 Name: magnesium.localdomain Address: 10.0.0.12 C:\Users\mark>ping magnesium Pinging magnesium.localdomain [67.215.65.132] with 32 bytes of data: Reply from 67.215.65.132: bytes=32 time=267ms TTL=57 Reply from 67.215.65.132: bytes=32 time=162ms TTL=57 Reply from 67.215.65.132: bytes=32 time=510ms TTL=57 Reply from 67.215.65.132: bytes=32 time=146ms TTL=57 Ping statistics for 67.215.65.132: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 146ms, Maximum = 510ms, Average = 271ms And from Linux: [root@beryllium ~]# ping -c4 magnesium PING magnesium.localdomain (10.0.0.12) 56(84) bytes of data. 64 bytes from magnesium.localdomain (10.0.0.12): icmp_seq=1 ttl=128 time=0.176 ms 64 bytes from magnesium.localdomain (10.0.0.12): icmp_seq=2 ttl=128 time=0.634 ms 64 bytes from magnesium.localdomain (10.0.0.12): icmp_seq=3 ttl=128 time=0.685 ms 64 bytes from magnesium.localdomain (10.0.0.12): icmp_seq=4 ttl=128 time=0.263 ms --- magnesium.localdomain ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 3002ms rtt min/avg/max/mdev = 0.176/0.439/0.685/0.223 ms [root@beryllium ~]# nslookup magnesium Server: 10.0.0.6 Address: 10.0.0.6#53 Name: magnesium.localdomain Address: 10.0.0.12 UPDATE 3 I stopped the Windows DNS client on my Windows 7 machine with net stop dnscache and it is now working fine. It would be nice to get DNS working with the DNS client on, but I might be OK without it, what do you think?

    Read the article

  • Which MAC address is the right one?

    - by Paul Dinh
    Result by 'getmac': C:\>getmac Physical Address Transport Name =================== ========================================================== 72-03-C6-48-59-34 \Device\Tcpip_{8AEB3263-18C4-449E-A80F-BC2541DDC2A9} 00-21-9B-D5-6F-EE \Device\Tcpip_{C2F9CE19-D68F-4105-9766-45CBE6D82331} 00-22-68-D2-9B-F7 \Device\Tcpip_{A2701130-9221-43FE-8F14-7B1114F84DC3} Result by 'ipconfig /all': C:\>ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : xps-m1530 Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Mixed IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No Ethernet adapter Wireless Network Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Dell Wireless 1395 WLAN Mini-Card Physical Address. . . . . . . . . : 00-22-68-D2-9B-F7 Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Autoconfiguration IP Address. . . : 169.254.246.4 Subnet Mask . . . . . . . . . . . : 255.255.0.0 Default Gateway . . . . . . . . . : Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Marvell Yukon 88E8040 PCI-E Fast Eth ernet Controller Physical Address. . . . . . . . . : 00-21-9B-D5-6F-EE Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 192.168.1.112 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.1.1 DHCP Server . . . . . . . . . . . : 192.168.1.1 DNS Servers . . . . . . . . . . . : 8.8.8.8 8.8.4.4 Lease Obtained. . . . . . . . . . : 01 November 2012 9:00:36 AM Lease Expires . . . . . . . . . . : 04 November 2012 9:00:36 AM There is a MAC address on the back of my laptop, but the sticker is no longer there. So I use the 'getmac' command to get the MAC addresses. But which address shown by 'getmac' above is the one matching the MAC in the sticker on the back of my laptop? Or am I mistaken something? 00-21-... is the ethernet adapter, 00-22-... is the wireless adapter, and 72-03-... is what?

    Read the article

  • WiFi & GbE Slow while Both Active.

    - by Mark Tomlin
    I'm having a problem with my WiFi network connection when I use my wired GbE connection concurrently on my Laptop. I'm using my WiFi for Internet access, and general web surfing and I'm using my GbE connection to connect to my PlayStation so I can stream media. The WiFi connection is via a Linksys 610N connected to my Cable Modem. Where as the GbE connection is a direct connection from my Ethernet port to the Ethernet port of the PS3 via a Cat-5 cable (no router in between this connection). As soon as I connect the cable from the PS3 to my Ethernet port on my Laptop the WiFi connection slows to a halt, but then allows for a connection to the web as normal but at much slower speeds for the things like BitTorrent that stops completely. It seems to me that Windows can't handle both connections at once. It will have both active but it can only accept and send packets on one device at one time. I can get WiFi connections to work to go to websites and the like, but once I use my GbE connection to share media between my Laptop and my PS3 the Wifi connection dies out and I no longer have access to the internet. I setup my connection on the PS3 and the Laptop following the insturctions posted here: http://forums.finalgear.com/problems/s14e01-ps3-size-problem-40642/#post1188132 And the following is the results of my ipconfig. Windows IP Configuration Host Name . . . . . . . . . . . . : dygear Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No Ethernet adapter WiFi: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Intel(R) PRO/Wireless 3945ABG Network Connection Physical Address. . . . . . . . . : 00-19-**-**-**-** Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 192.168.1.111 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.1.1 DHCP Server . . . . . . . . . . . : 192.168.1.1 DNS Servers . . . . . . . . . . . : 192.168.1.1 167.206.254.2 167.206.254.1 Lease Obtained. . . . . . . . . . : Wednesday, May 19, 2010 08:55:30 Lease Expires . . . . . . . . . . : Thursday, May 20, 2010 08:55:30 Ethernet adapter LAN: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Broadcom NetXtreme Gigabit Ethernet Physical Address. . . . . . . . . : 00-16-**-**-**-** Dhcp Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 192.168.1.50 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : Any ideas?

    Read the article

  • Cannot open root device xvda1 or unknown-block(0,0)

    - by svoop
    I'm putting together a Dom0 and three DomU (all Gentoo) with kernel 3.5.7 and Xen 4.1.1. Each Dom has it's own md (md0 for Dom0, md1 for Dom1 etc). Dom0 works fine so far, however, I'm stuck trying to create DomUs. It appears the xvda1 device on DomU is not created or accessible: Parsing config file dom1 domainbuilder: detail: xc_dom_allocate: cmdline="root=/dev/xvda1 console=hvc0 root=/dev/xvda1 ro 3", features="(null)" domainbuilder: detail: xc_dom_kernel_mem: called domainbuilder: detail: xc_dom_boot_xen_init: ver 4.1, caps xen-3.0-x86_64 xen-3.0-x86_32p hvm-3.0-x86_32 hvm-3.0-x86_32p hvm-3.0-x86_64 domainbuilder: detail: xc_dom_parse_image: called domainbuilder: detail: xc_dom_find_loader: trying multiboot-binary loader ... domainbuilder: detail: loader probe failed domainbuilder: detail: xc_dom_find_loader: trying Linux bzImage loader ... domainbuilder: detail: xc_dom_malloc : 10530 kB domainbuilder: detail: xc_dom_do_gunzip: unzip ok, 0x2f7a4f -> 0xa48888 domainbuilder: detail: loader probe OK xc: detail: elf_parse_binary: phdr: paddr=0x1000000 memsz=0x558000 xc: detail: elf_parse_binary: phdr: paddr=0x1558000 memsz=0x690e8 xc: detail: elf_parse_binary: phdr: paddr=0x15c2000 memsz=0x127c0 xc: detail: elf_parse_binary: phdr: paddr=0x15d5000 memsz=0x533000 xc: detail: elf_parse_binary: memory: 0x1000000 -> 0x1b08000 xc: detail: elf_xen_parse_note: GUEST_OS = "linux" xc: detail: elf_xen_parse_note: GUEST_VERSION = "2.6" xc: detail: elf_xen_parse_note: XEN_VERSION = "xen-3.0" xc: detail: elf_xen_parse_note: VIRT_BASE = 0xffffffff80000000 xc: detail: elf_xen_parse_note: ENTRY = 0xffffffff815d5210 xc: detail: elf_xen_parse_note: HYPERCALL_PAGE = 0xffffffff81001000 xc: detail: elf_xen_parse_note: FEATURES = "!writable_page_tables|pae_pgdir_above_4gb" xc: detail: elf_xen_parse_note: PAE_MODE = "yes" xc: detail: elf_xen_parse_note: LOADER = "generic" xc: detail: elf_xen_parse_note: unknown xen elf note (0xd) xc: detail: elf_xen_parse_note: SUSPEND_CANCEL = 0x1 xc: detail: elf_xen_parse_note: HV_START_LOW = 0xffff800000000000 xc: detail: elf_xen_parse_note: PADDR_OFFSET = 0x0 xc: detail: elf_xen_addr_calc_check: addresses: xc: detail: virt_base = 0xffffffff80000000 xc: detail: elf_paddr_offset = 0x0 xc: detail: virt_offset = 0xffffffff80000000 xc: detail: virt_kstart = 0xffffffff81000000 xc: detail: virt_kend = 0xffffffff81b08000 xc: detail: virt_entry = 0xffffffff815d5210 xc: detail: p2m_base = 0xffffffffffffffff domainbuilder: detail: xc_dom_parse_elf_kernel: xen-3.0-x86_64: 0xffffffff81000000 -> 0xffffffff81b08000 domainbuilder: detail: xc_dom_mem_init: mem 5000 MB, pages 0x138800 pages, 4k each domainbuilder: detail: xc_dom_mem_init: 0x138800 pages domainbuilder: detail: xc_dom_boot_mem_init: called domainbuilder: detail: x86_compat: guest xen-3.0-x86_64, address size 64 domainbuilder: detail: xc_dom_malloc : 10000 kB domainbuilder: detail: xc_dom_build_image: called domainbuilder: detail: xc_dom_alloc_segment: kernel : 0xffffffff81000000 -> 0xffffffff81b08000 (pfn 0x1000 + 0xb08 pages) domainbuilder: detail: xc_dom_pfn_to_ptr: domU mapping: pfn 0x1000+0xb08 at 0x7fdec9b85000 xc: detail: elf_load_binary: phdr 0 at 0x0x7fdec9b85000 -> 0x0x7fdeca0dd000 xc: detail: elf_load_binary: phdr 1 at 0x0x7fdeca0dd000 -> 0x0x7fdeca1460e8 xc: detail: elf_load_binary: phdr 2 at 0x0x7fdeca147000 -> 0x0x7fdeca1597c0 xc: detail: elf_load_binary: phdr 3 at 0x0x7fdeca15a000 -> 0x0x7fdeca1cd000 domainbuilder: detail: xc_dom_alloc_segment: phys2mach : 0xffffffff81b08000 -> 0xffffffff824cc000 (pfn 0x1b08 + 0x9c4 pages) domainbuilder: detail: xc_dom_pfn_to_ptr: domU mapping: pfn 0x1b08+0x9c4 at 0x7fdec91c1000 domainbuilder: detail: xc_dom_alloc_page : start info : 0xffffffff824cc000 (pfn 0x24cc) domainbuilder: detail: xc_dom_alloc_page : xenstore : 0xffffffff824cd000 (pfn 0x24cd) domainbuilder: detail: xc_dom_alloc_page : console : 0xffffffff824ce000 (pfn 0x24ce) domainbuilder: detail: nr_page_tables: 0x0000ffffffffffff/48: 0xffff000000000000 -> 0xffffffffffffffff, 1 table(s) domainbuilder: detail: nr_page_tables: 0x0000007fffffffff/39: 0xffffff8000000000 -> 0xffffffffffffffff, 1 table(s) domainbuilder: detail: nr_page_tables: 0x000000003fffffff/30: 0xffffffff80000000 -> 0xffffffffbfffffff, 1 table(s) domainbuilder: detail: nr_page_tables: 0x00000000001fffff/21: 0xffffffff80000000 -> 0xffffffff827fffff, 20 table(s) domainbuilder: detail: xc_dom_alloc_segment: page tables : 0xffffffff824cf000 -> 0xffffffff824e6000 (pfn 0x24cf + 0x17 pages) domainbuilder: detail: xc_dom_pfn_to_ptr: domU mapping: pfn 0x24cf+0x17 at 0x7fdece676000 domainbuilder: detail: xc_dom_alloc_page : boot stack : 0xffffffff824e6000 (pfn 0x24e6) domainbuilder: detail: xc_dom_build_image : virt_alloc_end : 0xffffffff824e7000 domainbuilder: detail: xc_dom_build_image : virt_pgtab_end : 0xffffffff82800000 domainbuilder: detail: xc_dom_boot_image: called domainbuilder: detail: arch_setup_bootearly: doing nothing domainbuilder: detail: xc_dom_compat_check: supported guest type: xen-3.0-x86_64 <= matches domainbuilder: detail: xc_dom_compat_check: supported guest type: xen-3.0-x86_32p domainbuilder: detail: xc_dom_compat_check: supported guest type: hvm-3.0-x86_32 domainbuilder: detail: xc_dom_compat_check: supported guest type: hvm-3.0-x86_32p domainbuilder: detail: xc_dom_compat_check: supported guest type: hvm-3.0-x86_64 domainbuilder: detail: xc_dom_update_guest_p2m: dst 64bit, pages 0x138800 domainbuilder: detail: clear_page: pfn 0x24ce, mfn 0x37ddee domainbuilder: detail: clear_page: pfn 0x24cd, mfn 0x37ddef domainbuilder: detail: xc_dom_pfn_to_ptr: domU mapping: pfn 0x24cc+0x1 at 0x7fdece675000 domainbuilder: detail: start_info_x86_64: called domainbuilder: detail: setup_hypercall_page: vaddr=0xffffffff81001000 pfn=0x1001 domainbuilder: detail: domain builder memory footprint domainbuilder: detail: allocated domainbuilder: detail: malloc : 20658 kB domainbuilder: detail: anon mmap : 0 bytes domainbuilder: detail: mapped domainbuilder: detail: file mmap : 0 bytes domainbuilder: detail: domU mmap : 21392 kB domainbuilder: detail: arch_setup_bootlate: shared_info: pfn 0x0, mfn 0xbaa6f domainbuilder: detail: shared_info_x86_64: called domainbuilder: detail: vcpu_x86_64: called domainbuilder: detail: vcpu_x86_64: cr3: pfn 0x24cf mfn 0x37dded domainbuilder: detail: launch_vm: called, ctxt=0x7fff224e4ea0 domainbuilder: detail: xc_dom_release: called Daemon running with PID 4639 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.5.7-gentoo (root@majordomo) (gcc version 4.5.4 (Gentoo 4.5.4 p1.0, pie-0.4.7) ) #1 SMP Tue Nov 20 10:49:51 CET 2012 [ 0.000000] Command line: root=/dev/xvda1 console=hvc0 root=/dev/xvda1 ro 3 [ 0.000000] ACPI in unprivileged domain disabled [ 0.000000] e820: BIOS-provided physical RAM map: [ 0.000000] Xen: [mem 0x0000000000000000-0x000000000009ffff] usable [ 0.000000] Xen: [mem 0x00000000000a0000-0x00000000000fffff] reserved [ 0.000000] Xen: [mem 0x0000000000100000-0x0000000138ffffff] usable [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] MPS support code is not built-in. [ 0.000000] Using acpi=off or acpi=noirq or pci=noacpi may have problem [ 0.000000] DMI not present or invalid. [ 0.000000] No AGP bridge found [ 0.000000] e820: last_pfn = 0x139000 max_arch_pfn = 0x400000000 [ 0.000000] e820: last_pfn = 0x100000 max_arch_pfn = 0x400000000 [ 0.000000] init_memory_mapping: [mem 0x00000000-0xffffffff] [ 0.000000] init_memory_mapping: [mem 0x100000000-0x138ffffff] [ 0.000000] NUMA turned off [ 0.000000] Faking a node at [mem 0x0000000000000000-0x0000000138ffffff] [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x138ffffff] [ 0.000000] NODE_DATA [mem 0x1387fc000-0x1387fffff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x00010000-0x00ffffff] [ 0.000000] DMA32 [mem 0x01000000-0xffffffff] [ 0.000000] Normal [mem 0x100000000-0x138ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00010000-0x0009ffff] [ 0.000000] node 0: [mem 0x00100000-0x138ffffff] [ 0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs [ 0.000000] No local APIC present [ 0.000000] APIC: disable apic facility [ 0.000000] APIC: switched to apic NOOP [ 0.000000] e820: cannot find a gap in the 32bit address range [ 0.000000] e820: PCI devices with unassigned 32bit BARs may break! [ 0.000000] e820: [mem 0x139100000-0x1394fffff] available for PCI devices [ 0.000000] Booting paravirtualized kernel on Xen [ 0.000000] Xen version: 4.1.1 (preserve-AD) [ 0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:1 nr_node_ids:1 [ 0.000000] PERCPU: Embedded 26 pages/cpu @ffff880138400000 s75712 r8192 d22592 u2097152 [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 1259871 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: root=/dev/xvda1 console=hvc0 root=/dev/xvda1 ro 3 [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] __ex_table already sorted, skipping sort [ 0.000000] Checking aperture... [ 0.000000] No AGP bridge found [ 0.000000] Memory: 4943980k/5128192k available (3937k kernel code, 448k absent, 183764k reserved, 1951k data, 524k init) [ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:4352 nr_irqs:256 16 [ 0.000000] Console: colour dummy device 80x25 [ 0.000000] console [tty0] enabled [ 0.000000] console [hvc0] enabled [ 0.000000] installing Xen timer for CPU 0 [ 0.000000] Detected 3411.602 MHz processor. [ 0.000999] Calibrating delay loop (skipped), value calculated using timer frequency.. 6823.20 BogoMIPS (lpj=3411602) [ 0.000999] pid_max: default: 32768 minimum: 301 [ 0.000999] Security Framework initialized [ 0.001355] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes) [ 0.002974] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.003441] Mount-cache hash table entries: 256 [ 0.003595] Initializing cgroup subsys cpuacct [ 0.003599] Initializing cgroup subsys freezer [ 0.003637] ENERGY_PERF_BIAS: Set to 'normal', was 'performance' [ 0.003637] ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8) [ 0.003643] CPU: Physical Processor ID: 0 [ 0.003645] CPU: Processor Core ID: 0 [ 0.003702] SMP alternatives: switching to UP code [ 0.011791] Freeing SMP alternatives: 12k freed [ 0.011835] Performance Events: unsupported p6 CPU model 42 no PMU driver, software events only. [ 0.011886] Brought up 1 CPUs [ 0.011998] Grant tables using version 2 layout. [ 0.012009] Grant table initialized [ 0.012034] NET: Registered protocol family 16 [ 0.012328] PCI: setting up Xen PCI frontend stub [ 0.015089] bio: create slab <bio-0> at 0 [ 0.015158] ACPI: Interpreter disabled. [ 0.015180] xen/balloon: Initialising balloon driver. [ 0.015180] xen-balloon: Initialising balloon driver. [ 0.015180] vgaarb: loaded [ 0.016126] SCSI subsystem initialized [ 0.016314] PCI: System does not support PCI [ 0.016320] PCI: System does not support PCI [ 0.016435] NetLabel: Initializing [ 0.016438] NetLabel: domain hash size = 128 [ 0.016440] NetLabel: protocols = UNLABELED CIPSOv4 [ 0.016447] NetLabel: unlabeled traffic allowed by default [ 0.016475] Switching to clocksource xen [ 0.017434] pnp: PnP ACPI: disabled [ 0.017501] NET: Registered protocol family 2 [ 0.017864] IP route cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.019322] TCP established hash table entries: 524288 (order: 11, 8388608 bytes) [ 0.020376] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 0.020497] TCP: Hash tables configured (established 524288 bind 65536) [ 0.020500] TCP: reno registered [ 0.020525] UDP hash table entries: 4096 (order: 5, 131072 bytes) [ 0.020564] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes) [ 0.020624] NET: Registered protocol family 1 [ 0.020658] PCI-DMA: Using software bounce buffering for IO (SWIOTLB) [ 0.020662] software IO TLB [mem 0xfb632000-0xff631fff] (64MB) mapped at [ffff8800fb632000-ffff8800ff631fff] [ 0.020750] platform rtc_cmos: registered platform RTC device (no PNP device found) [ 0.021378] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.023378] msgmni has been set to 9656 [ 0.023544] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.023549] io scheduler noop registered [ 0.023551] io scheduler deadline registered [ 0.023580] io scheduler cfq registered (default) [ 0.023650] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 0.023845] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.024082] Non-volatile memory driver v1.3 [ 0.024085] Linux agpgart interface v0.103 [ 0.024207] Event-channel device installed. [ 0.024265] [drm] Initialized drm 1.1.0 20060810 [ 0.024268] [drm:i915_init] *ERROR* drm/i915 can't work without intel_agp module! [ 0.025145] brd: module loaded [ 0.025565] loop: module loaded [ 0.045646] Initialising Xen virtual ethernet driver. [ 0.198264] i8042: PNP: No PS/2 controller found. Probing ports directly. [ 0.199096] i8042: No controller found [ 0.199139] mousedev: PS/2 mouse device common for all mice [ 0.259303] rtc_cmos rtc_cmos: rtc core: registered rtc_cmos as rtc0 [ 0.259353] rtc_cmos: probe of rtc_cmos failed with error -38 [ 0.259440] md: raid1 personality registered for level 1 [ 0.259542] nf_conntrack version 0.5.0 (16384 buckets, 65536 max) [ 0.259732] ip_tables: (C) 2000-2006 Netfilter Core Team [ 0.259747] TCP: cubic registered [ 0.259886] NET: Registered protocol family 10 [ 0.260031] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 0.260070] sit: IPv6 over IPv4 tunneling driver [ 0.260194] NET: Registered protocol family 17 [ 0.260213] Bridge firewalling registered [ 5.360075] XENBUS: Waiting for devices to initialise: 25s...20s...15s...10s...5s...0s...235s...230s...225s...220s...215s...210s...205s...200s...195s...190s...185s...180s...175s...170s...165s...160s...155s...150s...145s...140s...135s...130s...125s...120s...115s...110s...105s...100s...95s...90s...85s...80s...75s...70s...65s...60s...55s...50s...45s...40s...35s...30s...25s...20s...15s...10s...5s...0s... [ 270.360180] XENBUS: Timeout connecting to device: device/vbd/51713 (local state 3, remote state 1) [ 270.360273] md: Waiting for all devices to be available before autodetect [ 270.360277] md: If you don't use raid, use raid=noautodetect [ 270.360388] md: Autodetecting RAID arrays. [ 270.360392] md: Scanned 0 and added 0 devices. [ 270.360394] md: autorun ... [ 270.360395] md: ... autorun DONE. [ 270.360431] VFS: Cannot open root device "xvda1" or unknown-block(0,0): error -6 [ 270.360435] Please append a correct "root=" boot option; here are the available partitions: [ 270.360440] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 270.360444] Pid: 1, comm: swapper/0 Not tainted 3.5.7-gentoo #1 [ 270.360446] Call Trace: [ 270.360454] [<ffffffff813d2205>] ? panic+0xbe/0x1c5 [ 270.360459] [<ffffffff813d2358>] ? printk+0x4c/0x51 [ 270.360464] [<ffffffff815d5fb7>] ? mount_block_root+0x24f/0x26d [ 270.360469] [<ffffffff815d62b6>] ? prepare_namespace+0x168/0x192 [ 270.360474] [<ffffffff815d5ca7>] ? kernel_init+0x1b0/0x1c2 [ 270.360477] [<ffffffff815d5500>] ? loglevel+0x34/0x34 [ 270.360482] [<ffffffff813d5a64>] ? kernel_thread_helper+0x4/0x10 [ 270.360486] [<ffffffff813d4038>] ? retint_restore_args+0x5/0x6 [ 270.360490] [<ffffffff813d5a60>] ? gs_change+0x13/0x13 The config: name = "dom1" bootloader = "/usr/bin/pygrub" root = "/dev/xvda1 ro" extra = "3" # runlevel memory = 5000 disk = [ 'phy:/dev/md1,xvda1,w' ] # vif = [ 'ip=..., vifname=veth1' ] # none for now Here are some details on the Dom0 kernel (grepping for "xen"): CONFIG_XEN=y CONFIG_XEN_DOM0=y CONFIG_XEN_PRIVILEGED_GUEST=y CONFIG_XEN_PVHVM=y CONFIG_XEN_MAX_DOMAIN_MEMORY=500 CONFIG_XEN_SAVE_RESTORE=y CONFIG_PCI_XEN=y CONFIG_XEN_PCIDEV_FRONTEND=y # CONFIG_XEN_BLKDEV_FRONTEND is not set CONFIG_XEN_BLKDEV_BACKEND=y # CONFIG_XEN_NETDEV_FRONTEND is not set CONFIG_XEN_NETDEV_BACKEND=y CONFIG_INPUT_XEN_KBDDEV_FRONTEND=y CONFIG_HVC_XEN=y CONFIG_HVC_XEN_FRONTEND=y # CONFIG_XEN_WDT is not set # CONFIG_XEN_FBDEV_FRONTEND is not set # Xen driver support CONFIG_XEN_BALLOON=y # CONFIG_XEN_SELFBALLOONING is not set CONFIG_XEN_SCRUB_PAGES=y CONFIG_XEN_DEV_EVTCHN=y CONFIG_XEN_BACKEND=y CONFIG_XENFS=y CONFIG_XEN_COMPAT_XENFS=y CONFIG_XEN_SYS_HYPERVISOR=y CONFIG_XEN_XENBUS_FRONTEND=y CONFIG_XEN_GNTDEV=m CONFIG_XEN_GRANT_DEV_ALLOC=m CONFIG_SWIOTLB_XEN=y CONFIG_XEN_TMEM=y CONFIG_XEN_PCIDEV_BACKEND=m CONFIG_XEN_PRIVCMD=y CONFIG_XEN_ACPI_PROCESSOR=m And the DomU kernel (grepping for "xen"): CONFIG_XEN=y CONFIG_XEN_DOM0=y CONFIG_XEN_PRIVILEGED_GUEST=y CONFIG_XEN_PVHVM=y CONFIG_XEN_MAX_DOMAIN_MEMORY=500 CONFIG_XEN_SAVE_RESTORE=y CONFIG_PCI_XEN=y CONFIG_XEN_PCIDEV_FRONTEND=y CONFIG_XEN_BLKDEV_FRONTEND=y CONFIG_XEN_NETDEV_FRONTEND=y CONFIG_INPUT_XEN_KBDDEV_FRONTEND=y CONFIG_HVC_XEN=y CONFIG_HVC_XEN_FRONTEND=y # CONFIG_XEN_WDT is not set # CONFIG_XEN_FBDEV_FRONTEND is not set # Xen driver support CONFIG_XEN_BALLOON=y # CONFIG_XEN_SELFBALLOONING is not set CONFIG_XEN_SCRUB_PAGES=y CONFIG_XEN_DEV_EVTCHN=y # CONFIG_XEN_BACKEND is not set CONFIG_XENFS=y CONFIG_XEN_COMPAT_XENFS=y CONFIG_XEN_SYS_HYPERVISOR=y CONFIG_XEN_XENBUS_FRONTEND=y CONFIG_XEN_GNTDEV=m CONFIG_XEN_GRANT_DEV_ALLOC=m CONFIG_SWIOTLB_XEN=y CONFIG_XEN_TMEM=y CONFIG_XEN_PRIVCMD=y CONFIG_XEN_ACPI_PROCESSOR=m Any ideas what I'm doing wrong here? Thanks a lot!

    Read the article

  • Unexpected multiple network connections on Windows Vista

    - by Jens
    My Network and Sharing Center shows multiple connections to the internet, where only one is expected: My internet access works fine, but since the "Unidentified Network" is set to public after each boot, sharing and network discovery don't work as well. Similar questions on Google point mostly to the Bonjour service, but I am sure that this is not, and never was, installed on this machine. So: How can I get rid of the unidentified network? Output of ipconfig /all: Windows IP Configuration Host Name . . . . . . . . . . . . : ***** Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : mySuffix Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : mySuffix Description . . . . . . . . . . . : Intel(R) 82567LF-3 Gigabit Network Connection Physical Address. . . . . . . . . : 00-19-99-65-F0-B2 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::c90:2d23:7651:42f%10(Preferred) IPv4 Address. . . . . . . . . . . : 192.168.141.130(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : 13 November 2012 09:40:54 Lease Expires . . . . . . . . . . : 21 November 2012 09:45:01 Default Gateway . . . . . . . . . : 192.168.141.109 192.168.141.108 DHCP Server . . . . . . . . . . . : 192.168.141.120 DHCPv6 IAID . . . . . . . . . . . : 218110361 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-12-DD-00-AF-00-19-99-65-F0-B2 DNS Servers . . . . . . . . . . . : 8.8.8.8 8.8.4.4 NetBIOS over Tcpip. . . . . . . . : Enabled Tunnel adapter Local Area Connection* 13: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : mySuffix Description . . . . . . . . . . . : Microsoft ISATAP Adapter Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes

    Read the article

  • JBoss https on port other than 8080 not working

    - by MilindaD
    We have a server with two JBoss instances where one runs on 8080, the other on 8081. We need to have HTTPS enabled for the 8081 server, firstly we tried enabling https on the 8080 port instance by generating the keystore and editing the server.xml and it successfully worked. However when we tried the same thing for 8081 it did not, note that we removed https for the 8080 server first before enabling it for 8081. This is what was used for both server.xml for 8080 and 8081. The only difference was that the port was changed from 8080 to 8081 when trying to enable https for 8081 port instance. What am I doing wrong and what needs to be changed? NOTE : When I meant enabled for 8080 I meant when you visit https:// URL:8484 you will actually be visiting the 8080 port instance. However when ssl is enabled for 8081 and I visit https:// URL:8484 I get that the web page is unavailable. COMMENTLESS VERSION <Server> <Listener className="org.apache.catalina.core.AprLifecycleListener" SSLEngine="on" /> <Listener className="org.apache.catalina.core.JasperListener" /> <Service name="jboss.web"> <!-- https --> <Connector port="8080" address="${jboss.bind.address}" maxThreads="350" maxHttpHeaderSize="8192" emptySessionPath="true" protocol="HTTP/1.1" enableLookups="false" redirectPort="8443" acceptCount="100" connectionTimeout="20000" disableUploadTimeout="true" compression="on" ompressableMimeType="text/html,text/css,text/javascript,application/json,text/xml,text/plain,application/x-javascript,application/javascript"/> <Connector port="8443" protocol="HTTP/1.1" SSLEnabled="true" maxThreads="150" scheme="https" secure="true" clientAuth="false" sslProtocol="TLS" address="${jboss.bind.address}" keystoreFile="${jboss.server.home.dir}/conf/supun1.keystore" keystorePass="aaaaaa" truststoreFile="${jboss.server.home.dir}/conf/supun1.keystore" truststorePass="aaaaaa" /> <!-- https1 --> <Connector port="8009" address="${jboss.bind.address}" protocol="AJP/1.3" emptySessionPath="true" enableLookups="false" redirectPort="8443" /> <Engine name="jboss.web" defaultHost="localhost" jvmRoute="khms1"> <Realm className="org.jboss.web.tomcat.security.JBossSecurityMgrRealm" certificatePrincipal="org.jboss.security.auth.certs.SubjectDNMapping" allRolesMode="authOnly" /> <Host name="localhost" autoDeploy="false" deployOnStartup="false" deployXML="false" configClass="org.jboss.web.tomcat.security.config.JBossContextConfig" > <Valve className="org.jboss.web.tomcat.service.sso.ClusteredSingleSignOn" /> <Valve className="org.jboss.web.tomcat.service.jca.CachedConnectionValve" cachedConnectionManagerObjectName="jboss.jca:service=CachedConnectionManager" transactionManagerObjectName="jboss:service=TransactionManager" /> </Host> </Engine> </Service> </Server> WITH COMMENTS VERSION <Server> <!--APR library loader. Documentation at /docs/apr.html --> <Listener className="org.apache.catalina.core.AprLifecycleListener" SSLEngine="on" /> <!--Initialize Jasper prior to webapps are loaded. Documentation at /docs/jasper-howto.html --> <Listener className="org.apache.catalina.core.JasperListener" /> <!-- Use a custom version of StandardService that allows the connectors to be started independent of the normal lifecycle start to allow web apps to be deployed before starting the connectors. --> <Service name="jboss.web"> <!-- A "Connector" represents an endpoint by which requests are received and responses are returned. Documentation at : Java HTTP Connector: /docs/config/http.html (blocking & non-blocking) Java AJP Connector: /docs/config/ajp.html APR (HTTP/AJP) Connector: /docs/apr.html Define a non-SSL HTTP/1.1 Connector on port 8080 --> <Connector port="8080" address="${jboss.bind.address}" maxThreads="350" maxHttpHeaderSize="8192" emptySessionPath="true" protocol="HTTP/1.1" enableLookups="false" redirectPort="8443" acceptCount="100" connectionTimeout="20000" disableUploadTimeout="true" compression="on" ompressableMimeType="text/html,text/css,text/javascript,application/json,text/xml,text/plain,application/x-javascript,application/javascript"/> <!-- Define a SSL HTTP/1.1 Connector on port 8443 This connector uses the JSSE configuration, when using APR, the connector should be using the OpenSSL style configuration described in the APR documentation --> <!-- <Connector port="8443" protocol="HTTP/1.1" SSLEnabled="true" maxThreads="150" scheme="https" secure="true" keystoreFile="${jboss.server.home.dir}/conf/zara.keystore" keystorePass="zara2010" clientAuth="false" sslProtocol="TLS" compression="on" /> --> <Connector port="8443" protocol="HTTP/1.1" SSLEnabled="true" maxThreads="150" scheme="https" secure="true" clientAuth="false" sslProtocol="TLS" address="${jboss.bind.address}" keystoreFile="${jboss.server.home.dir}/conf/supun1.keystore" keystorePass="aaaaaa" truststoreFile="${jboss.server.home.dir}/conf/supun1.keystore" truststorePass="aaaaaa" /> <!-- Define an AJP 1.3 Connector on port 8009 --> <Connector port="8009" address="${jboss.bind.address}" protocol="AJP/1.3" emptySessionPath="true" enableLookups="false" redirectPort="8443" /> <Engine name="jboss.web" defaultHost="localhost" jvmRoute="khms1"> <!-- The JAAS based authentication and authorization realm implementation that is compatible with the jboss 3.2.x realm implementation. - certificatePrincipal : the class name of the org.jboss.security.auth.certs.CertificatePrincipal impl used for mapping X509[] cert chains to a Princpal. - allRolesMode : how to handle an auth-constraint with a role-name=*, one of strict, authOnly, strictAuthOnly + strict = Use the strict servlet spec interpretation which requires that the user have one of the web-app/security-role/role-name + authOnly = Allow any authenticated user + strictAuthOnly = Allow any authenticated user only if there are no web-app/security-roles --> <Realm className="org.jboss.web.tomcat.security.JBossSecurityMgrRealm" certificatePrincipal="org.jboss.security.auth.certs.SubjectDNMapping" allRolesMode="authOnly" /> <!-- A subclass of JBossSecurityMgrRealm that uses the authentication behavior of JBossSecurityMgrRealm, but overrides the authorization checks to use JACC permissions with the current java.security.Policy to determine authorized access. - allRolesMode : how to handle an auth-constraint with a role-name=*, one of strict, authOnly, strictAuthOnly + strict = Use the strict servlet spec interpretation which requires that the user have one of the web-app/security-role/role-name + authOnly = Allow any authenticated user + strictAuthOnly = Allow any authenticated user only if there are no web-app/security-roles <Realm className="org.jboss.web.tomcat.security.JaccAuthorizationRealm" certificatePrincipal="org.jboss.security.auth.certs.SubjectDNMapping" allRolesMode="authOnly" /> --> <Host name="localhost" autoDeploy="false" deployOnStartup="false" deployXML="false" configClass="org.jboss.web.tomcat.security.config.JBossContextConfig" > <!-- Uncomment to enable request dumper. This Valve "logs interesting contents from the specified Request (before processing) and the corresponding Response (after processing). It is especially useful in debugging problems related to headers and cookies." --> <!-- <Valve className="org.apache.catalina.valves.RequestDumperValve" /> --> <!-- Access logger --> <!-- <Valve className="org.apache.catalina.valves.AccessLogValve" prefix="localhost_access_log." suffix=".log" pattern="common" directory="${jboss.server.log.dir}" resolveHosts="false" /> --> <!-- Uncomment to enable single sign-on across web apps deployed to this host. Does not provide SSO across a cluster. If this valve is used, do not use the JBoss ClusteredSingleSignOn valve shown below. A new configuration attribute is available beginning with release 4.0.4: cookieDomain configures the domain to which the SSO cookie will be scoped (i.e. the set of hosts to which the cookie will be presented). By default the cookie is scoped to "/", meaning the host that presented it. Set cookieDomain to a wider domain (e.g. "xyz.com") to allow an SSO to span more than one hostname. --> <!-- <Valve className="org.apache.catalina.authenticator.SingleSignOn" /> --> <!-- Uncomment to enable single sign-on across web apps deployed to this host AND to all other hosts in the cluster. If this valve is used, do not use the standard Tomcat SingleSignOn valve shown above. Valve uses a JBossCache instance to support SSO credential caching and replication across the cluster. The JBossCache instance must be configured separately. By default, the valve shares a JBossCache with the service that supports HttpSession replication. See the "jboss-web-cluster-service.xml" file in the server/all/deploy directory for cache configuration details. Besides the attributes supported by the standard Tomcat SingleSignOn valve (see the Tomcat docs), this version also supports the following attributes: cookieDomain see above treeCacheName JMX ObjectName of the JBossCache MBean used to support credential caching and replication across the cluster. If not set, the default value is "jboss.cache:service=TomcatClusteringCache", the standard ObjectName of the JBossCache MBean used to support session replication. --> <Valve className="org.jboss.web.tomcat.service.sso.ClusteredSingleSignOn" /> <!-- Check for unclosed connections and transaction terminated checks in servlets/jsps. Important: The dependency on the CachedConnectionManager in META-INF/jboss-service.xml must be uncommented, too --> <Valve className="org.jboss.web.tomcat.service.jca.CachedConnectionValve" cachedConnectionManagerObjectName="jboss.jca:service=CachedConnectionManager" transactionManagerObjectName="jboss:service=TransactionManager" /> </Host> </Engine> </Service> </Server>

    Read the article

  • Can't ping localhost/or reach locally hosted domain

    - by Ian
    I can't reach a locally hosted domain, and in testing I have discovered I can't ping localhost or the actual IP either. OS is Windows7 64bit, Pro. DNS works, I can ping others on my network, they can ping me, and they can reach the hosted domain. The ONLY problem I have found is that I can't reach the locally hosted domains! C:\Users\ianipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : leda Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : hcs Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : hcs Description . . . . . . . . . . . : Atheros AR8121/AR8113/AR8114 PCI-E Ethern et Controller Physical Address. . . . . . . . . : 00-23-54-7C-E2-2A DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 192.168.0.12(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.0.1 DNS Servers . . . . . . . . . . . : 192.168.0.1 NetBIOS over Tcpip. . . . . . . . : Enabled Ethernet adapter VirtualBox Host-Only Network #2: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : VirtualBox Host-Only Ethernet Adapter #2 Physical Address. . . . . . . . . : 08-00-27-00-88-4A DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Autoconfiguration IPv4 Address. . : 169.254.205.215(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.0.0 Default Gateway . . . . . . . . . : NetBIOS over Tcpip. . . . . . . . : Enabled C:\Users\ianping localhost Pinging leda [127.0.0.1] with 32 bytes of data: Request timed out. Request timed out. Request timed out. Request timed out. Ping statistics for 127.0.0.1: Packets: Sent = 4, Received = 0, Lost = 4 (100% loss), C:\Users\ianping coachmaster.leda.hcs Pinging coachmaster.leda.hcs [192.168.0.12] with 32 bytes of data: Request timed out. Request timed out. Request timed out. Request timed out. Ping statistics for 192.168.0.12: Packets: Sent = 4, Received = 0, Lost = 4 (100% loss), C:\Users\ian I can reach a hosted VM in VirtualBox and the VM can browse the hosted sites. I've removed Zone Alarm and disabled Windows Firewall - same results. So how can I browse my locally hosted sited? What could be blocking it? Thanks Ian

    Read the article

  • connecting to a network using route command

    - by ami
    I have a computer with an external IP(192.168.223.220) and also an internal address (10.1.1.20) in order to connect to some servers that don't have external addresses only 10.1.1.xx . in order to connect to these servers from other machines I used the following command "route ADD 10.1.1.0 MASK 255.255.255.0 192.168.223.220" and than I was able to connect to the servers using there 10.1.1.xx address. The problem is that the hard disk of main server(192.168.223.220) died and was replaced and after the that I am not able to connect to the servers as before, the route command succeeds and I can ping 10.1.1.20 but not the other servers. Thanks I am using Windows XP and the print outs are D:\AurosHome\Scriptsipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : N100-master Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Unknown IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No Ethernet adapter Local Area Connection 3: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Intel(R) PRO/1000 EB Network Connection with I/O Acceleration #2 Physical Address. . . . . . . . . : 00-30-48-34-BA-B9 Dhcp Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 192.168.225.180 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.225.254 DNS Servers . . . . . . . . . . . : 192.168.225.2 Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Intel(R) PRO/1000 EB Network Connection with I/O Acceleration Physical Address. . . . . . . . . : 00-30-48-34-BA-B8 Dhcp Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 10.1.1.20 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : Ethernet adapter Local Area Connection 2: Media State . . . . . . . . . . . : Media disconnected Description . . . . . . . . . . . : Mellanox IPoIB Adapter Physical Address. . . . . . . . . : 00-02-C9-25-34-0D D:\AurosHome\Scriptsroute print Interface List 0x1 ........................... MS TCP Loopback interface 0x2 ...00 30 48 34 ba b9 ...... Intel(R) PRO/1000 EB Network Connection with I/O Acceleration #2 - Packet Sche duler Miniport 0x3 ...00 30 48 34 ba b8 ...... Intel(R) PRO/1000 EB Network Connection with I/O Acceleration - Packet Schedul er Miniport 0x10005 ...00 02 c9 25 34 0d ...... Mellanox IPoIB Adapter - Packet Scheduler Miniport =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.225.254 192.168.225.180 10 10.1.1.0 255.255.255.0 10.1.1.20 10.1.1.20 10 10.1.1.20 255.255.255.255 127.0.0.1 127.0.0.1 10 10.255.255.255 255.255.255.255 10.1.1.20 10.1.1.20 10 127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1 192.168.225.0 255.255.255.0 192.168.225.180 192.168.225.180 10 192.168.225.180 255.255.255.255 127.0.0.1 127.0.0.1 10 192.168.225.255 255.255.255.255 192.168.225.180 192.168.225.180 10 224.0.0.0 240.0.0.0 10.1.1.20 10.1.1.20 10 224.0.0.0 240.0.0.0 192.168.225.180 192.168.225.180 10 255.255.255.255 255.255.255.255 10.1.1.20 10.1.1.20 1 255.255.255.255 255.255.255.255 10.1.1.20 10005 1 255.255.255.255 255.255.255.255 192.168.225.180 192.168.225.180 1 Default Gateway: 192.168.225.254 Persistent Routes: None

    Read the article

  • Tip/Trick: Fix Common SEO Problems Using the URL Rewrite Extension

    - by ScottGu
    Search engine optimization (SEO) is important for any publically facing web-site.  A large % of traffic to sites now comes directly from search engines, and improving your site’s search relevancy will lead to more users visiting your site from search engine queries.  This can directly or indirectly increase the money you make through your site. This blog post covers how you can use the free Microsoft URL Rewrite Extension to fix a bunch of common SEO problems that your site might have.  It takes less than 15 minutes (and no code changes) to apply 4 simple URL Rewrite rules to your site, and in doing so cause search engines to drive more visitors and traffic to your site.  The techniques below work equally well with both ASP.NET Web Forms and ASP.NET MVC based sites.  They also works with all versions of ASP.NET (and even work with non-ASP.NET content). [In addition to blogging, I am also now using Twitter for quick updates and to share links. Follow me at: twitter.com/scottgu] Measuring the SEO of your website with the Microsoft SEO Toolkit A few months ago I blogged about the free SEO Toolkit that we’ve shipped.  This useful tool enables you to automatically crawl/scan your site for SEO correctness, and it then flags any SEO issues it finds.  I highly recommend downloading and using the tool against any public site you work on.  It makes it easy to spot SEO issues you might have in your site, and pinpoint ways to optimize it further. Below is a simple example of a report I ran against one of my sites (www.scottgu.com) prior to applying the URL Rewrite rules I’ll cover later in this blog post:   Search Relevancy and URL Splitting Two of the important things that search engines evaluate when assessing your site’s “search relevancy” are: How many other sites link to your content.  Search engines assume that if a lot of people around the web are linking to your content, then it is likely useful and so weight it higher in relevancy. The uniqueness of the content it finds on your site.  If search engines find that the content is duplicated in multiple places around the Internet (or on multiple URLs on your site) then it is likely to drop the relevancy of the content. One of the things you want to be very careful to avoid when building public facing sites is to not allow different URLs to retrieve the same content within your site.  Doing so will hurt with both of the situations above.  In particular, allowing external sites to link to the same content with multiple URLs will cause your link-count and page-ranking to be split up across those different URLs (and so give you a smaller page rank than what it would otherwise be if it was just one URL).  Not allowing external sites to link to you in different ways sounds easy in theory – but you might wonder what exactly this means in practice and how you avoid it. 4 Really Common SEO Problems Your Sites Might Have Below are 4 really common scenarios that can cause your site to inadvertently expose multiple URLs for the same content.  When this happens external sites linking to yours will end up splitting their page links across multiple URLs - and as a result cause you to have a lower page ranking with search engines than you deserve. SEO Problem #1: Default Document IIS (and other web servers) supports the concept of a “default document”.  This allows you to avoid having to explicitly specify the page you want to serve at either the root of the web-site/application, or within a sub-directory.  This is convenient – but means that by default this content is available via two different publically exposed URLs (which is bad).  For example: http://scottgu.com/ http://scottgu.com/default.aspx SEO Problem #2: Different URL Casings Web developers often don’t realize URLs are case sensitive to search engines on the web.  This means that search engines will treat the following links as two completely different URLs: http://scottgu.com/Albums.aspx http://scottgu.com/albums.aspx SEO Problem #3: Trailing Slashes Consider the below two URLs – they might look the same at first, but they are subtly different. The trailing slash creates yet another situation that causes search engines to treat the URLs as different and so split search rankings: http://scottgu.com http://scottgu.com/ SEO Problem #4: Canonical Host Names Sometimes sites support scenarios where they support a web-site with both a leading “www” hostname prefix as well as just the hostname itself.  This causes search engines to treat the URLs as different and split search rankling: http://scottgu.com/albums.aspx/ http://www.scottgu.com/albums.aspx/ How to Easily Fix these SEO Problems in 10 minutes (or less) using IIS Rewrite If you haven’t been careful when coding your sites, chances are you are suffering from one (or more) of the above SEO problems.  Addressing these issues will improve your search engine relevancy ranking and drive more traffic to your site. The “good news” is that fixing the above 4 issues is really easy using the URL Rewrite Extension.  This is a completely free Microsoft extension available for IIS 7.x (on Windows Server 2008, Windows Server 2008 R2, Windows 7 and Windows Vista).  The great thing about using the IIS Rewrite extension is that it allows you to fix the above problems *without* having to change any code within your applications.  You can easily install the URL Rewrite Extension in under 3 minutes using the Microsoft Web Platform Installer (a free tool we ship that automates setting up web servers and development machines).  Just click the green “Install Now” button on the URL Rewrite Spotlight page to install it on your Windows Server 2008, Windows 7 or Windows Vista machine: Once installed you’ll find that a new “URL Rewrite” icon is available within the IIS 7 Admin Tool: Double-clicking the icon will open up the URL Rewrite admin panel – which will display the list of URL Rewrite rules configured for a particular application or site: Notice that our rewrite rule list above is currently empty (which is the default when you first install the extension).  We can click the “Add Rule…” link button in the top-right of the panel to add and enable new URL Rewriting logic for our site.  Scenario 1: Handling Default Document Scenarios One of the SEO problems I discussed earlier in this post was the scenario where the “default document” feature of IIS causes you to inadvertently expose two URLs for the same content on your site.  For example: http://scottgu.com/ http://scottgu.com/default.aspx We can fix this by adding a new IIS Rewrite rule that automatically redirects anyone who navigates to the second URL to instead go to the first one.  We will setup the HTTP redirect to be a “permanent redirect” – which will indicate to search engines that they should follow the redirect and use the new URL they are redirected to as the identifier of the content they retrieve.  Let’s look at how we can create such a rule.  We’ll begin by clicking the “Add Rule” link in the screenshot above.  This will cause the below dialog to display: We’ll select the “Blank Rule” template within the “Inbound rules” section to create a new custom URL Rewriting rule.  This will display an empty pane like below: Don’t worry – setting up the above rule is easy.  The following 4 steps explain how to do so: Step 1: Name the Rule Our first step will be to name the rule we are creating.  Naming it with a descriptive name will make it easier to find and understand later.  Let’s name this rule our “Default Document URL Rewrite” rule: Step 2: Setup the Regular Expression that Matches this Rule Our second step will be to specify a regular expression filter that will cause this rule to execute when an incoming URL matches the regex pattern.   Don’t worry if you aren’t good with regular expressions - I suck at them too. The trick is to know someone who is good at them or copy/paste them from a web-site.  Below we are going to specify the following regular expression as our pattern rule: (.*?)/?Default\.aspx$ This pattern will match any URL string that ends with Default.aspx. The "(.*?)" matches any preceding character zero or more times. The "/?" part says to match the slash symbol zero or one times. The "$" symbol at the end will ensure that the pattern will only match strings that end with Default.aspx.  Combining all these regex elements allows this rule to work not only for the root of your web site (e.g. http://scottgu.com/default.aspx) but also for any application or subdirectory within the site (e.g. http://scottgu.com/photos/default.aspx.  Because the “ignore case” checkbox is selected it will match both “Default.aspx” as well as “default.aspx” within the URL.   One nice feature built-into the rule editor is a “Test pattern” button that you can click to bring up a dialog that allows you to test out a few URLs with the rule you are configuring: Above I've added a “products/default.aspx” URL and clicked the “Test” button.  This will give me immediate feedback on whether the rule will execute for it.  Step 3: Setup a Permanent Redirect Action We’ll then setup an action to occur when our regular expression pattern matches the incoming URL: In the dialog above I’ve changed the “Action Type” drop down to be a “Redirect” action.  The “Redirect Type” will be a HTTP 301 Permanent redirect – which means search engines will follow it. I’ve also set the “Redirect URL” property to be: {R:1}/ This indicates that we want to redirect the web client requesting the original URL to a new URL that has the originally requested URL path - minus the "Default.aspx" in it.  For example, requests for http://scottgu.com/default.aspx will be redirected to http://scottgu.com/, and requests for http://scottgu.com/photos/default.aspx will be redirected to http://scottgu.com/photos/ The "{R:N}" regex construct, where N >= 0, is called a back-reference and N is the back-reference index. In the case of our pattern "(.*?)/?Default\.aspx$", if the input URL is "products/Default.aspx" then {R:0} will contain "products/Default.aspx" and {R:1} will contain "products".  We are going to use this {R:1}/ value to be the URL we redirect users to.  Step 4: Apply and Save the Rule Our final step is to click the “Apply” button in the top right hand of the IIS admin tool – which will cause the tool to persist the URL Rewrite rule into our application’s root web.config file (under a <system.webServer/rewrite> configuration section): <configuration>     <system.webServer>         <rewrite>             <rules>                 <rule name="Default Document" stopProcessing="true">                     <match url="(.*?)/?Default\.aspx$" />                     <action type="Redirect" url="{R:1}/" />                 </rule>             </rules>         </rewrite>     </system.webServer> </configuration> Because IIS 7.x and ASP.NET share the same web.config files, you can actually just copy/paste the above code into your web.config files using Visual Studio and skip the need to run the admin tool entirely.  This also makes adding/deploying URL Rewrite rules with your ASP.NET applications really easy. Step 5: Try the Rule Out Now that we’ve saved the rule, let’s try it out on our site.  Try the following two URLs on my site: http://scottgu.com/ http://scottgu.com/default.aspx Notice that the second URL automatically redirects to the first one.  Because it is a permanent redirect, search engines will follow the URL and should update the page ranking of http://scottgu.com to include links to http://scottgu.com/default.aspx as well. Scenario 2: Different URL Casing Another common SEO problem I discussed earlier in this post is that URLs are case sensitive to search engines on the web.  This means that search engines will treat the following links as two completely different URLs: http://scottgu.com/Albums.aspx http://scottgu.com/albums.aspx We can fix this by adding a new IIS Rewrite rule that automatically redirects anyone who navigates to the first URL to instead go to the second (all lower-case) one.  Like before, we will setup the HTTP redirect to be a “permanent redirect” – which will indicate to search engines that they should follow the redirect and use the new URL they are redirected to as the identifier of the content they retrieve. To create such a rule we’ll click the “Add Rule” link in the URL Rewrite admin tool again.  This will cause the “Add Rule” dialog to appear again: Unlike the previous scenario (where we created a “Blank Rule”), with this scenario we can take advantage of a built-in “Enforce lowercase URLs” rule template.  When we click the “ok” button we’ll see the following dialog which asks us if we want to create a rule that enforces the use of lowercase letters in URLs: When we click the “Yes” button we’ll get a pre-written rule that automatically performs a permanent redirect if an incoming URL has upper-case characters in it – and automatically send users to a lower-case version of the URL: We can click the “Apply” button to use this rule “as-is” and have it apply to all incoming URLs to our site.  Because my www.scottgu.com site uses ASP.NET Web Forms, I’m going to make one small change to the rule we generated above – which is to add a condition that will ensure that URLs to ASP.NET’s built-in “WebResource.axd” handler are excluded from our case-sensitivity URL Rewrite logic.  URLs to the WebResource.axd handler will only come from server-controls emitted from my pages – and will never be linked to from external sites.  While my site will continue to function fine if we redirect these URLs to automatically be lower-case – doing so isn’t necessary and will add an extra HTTP redirect to many of my pages.  The good news is that adding a condition that prevents my URL Rewriting rule from happening with certain URLs is easy.  We simply need to expand the “Conditions” section of the form above We can then click the “Add” button to add a condition clause.  This will bring up the “Add Condition” dialog: Above I’ve entered {URL} as the Condition input – and said that this rule should only execute if the URL does not match a regex pattern which contains the string “WebResource.axd”.  This will ensure that WebResource.axd URLs to my site will be allowed to execute just fine without having the URL be re-written to be all lower-case. Note: If you have static resources (like references to .jpg, .css, and .js files) within your site that currently use upper-case characters you’ll probably want to add additional condition filter clauses so that URLs to them also don’t get redirected to be lower-case (just add rules for patterns like .jpg, .gif, .js, etc).  Your site will continue to work fine if these URLs get redirected to be lower case (meaning the site won’t break) – but it will cause an extra HTTP redirect to happen on your site for URLs that don’t need to be redirected for SEO reasons.  So setting up a condition clause makes sense to add. When I click the “ok” button above and apply our lower-case rewriting rule the admin tool will save the following additional rule to our web.config file: <configuration>     <system.webServer>         <rewrite>             <rules>                 <rule name="Default Document" stopProcessing="true">                     <match url="(.*?)/?Default\.aspx$" />                     <action type="Redirect" url="{R:1}/" />                 </rule>                 <rule name="Lower Case URLs" stopProcessing="true">                     <match url="[A-Z]" ignoreCase="false" />                     <conditions logicalGrouping="MatchAll" trackAllCaptures="false">                         <add input="{URL}" pattern="WebResource.axd" negate="true" />                     </conditions>                     <action type="Redirect" url="{ToLower:{URL}}" />                 </rule>             </rules>         </rewrite>     </system.webServer> </configuration> Try the Rule Out Now that we’ve saved the rule, let’s try it out on our site.  Try the following two URLs on my site: http://scottgu.com/Albums.aspx http://scottgu.com/albums.aspx Notice that the first URL (which has a capital “A”) automatically does a redirect to a lower-case version of the URL.  Scenario 3: Trailing Slashes Another common SEO problem I discussed earlier in this post is the scenario of trailing slashes within URLs.  The trailing slash creates yet another situation that causes search engines to treat the URLs as different and so split search rankings: http://scottgu.com http://scottgu.com/ We can fix this by adding a new IIS Rewrite rule that automatically redirects anyone who navigates to the first URL (that does not have a trailing slash) to instead go to the second one that does.  Like before, we will setup the HTTP redirect to be a “permanent redirect” – which will indicate to search engines that they should follow the redirect and use the new URL they are redirected to as the identifier of the content they retrieve.  To create such a rule we’ll click the “Add Rule” link in the URL Rewrite admin tool again.  This will cause the “Add Rule” dialog to appear again: The URL Rewrite admin tool has a built-in “Append or remove the trailing slash symbol” rule template.  When we select it and click the “ok” button we’ll see the following dialog which asks us if we want to create a rule that automatically redirects users to a URL with a trailing slash if one isn’t present: Like within our previous lower-casing rewrite rule we’ll add one additional condition clause that will exclude WebResource.axd URLs from being processed by this rule.  This will avoid an unnecessary redirect for happening for those URLs. When we click the “OK” button we’ll get a pre-written rule that automatically performs a permanent redirect if the URL doesn’t have a trailing slash – and if the URL is not processed by either a directory or a file.  This will save the following additional rule to our web.config file: <configuration>     <system.webServer>         <rewrite>             <rules>                 <rule name="Default Document" stopProcessing="true">                     <match url="(.*?)/?Default\.aspx$" />                     <action type="Redirect" url="{R:1}/" />                 </rule>                 <rule name="Lower Case URLs" stopProcessing="true">                     <match url="[A-Z]" ignoreCase="false" />                     <conditions logicalGrouping="MatchAll" trackAllCaptures="false">                         <add input="{URL}" pattern="WebResource.axd" negate="true" />                     </conditions>                     <action type="Redirect" url="{ToLower:{URL}}" />                 </rule>                 <rule name="Trailing Slash" stopProcessing="true">                     <match url="(.*[^/])$" />                     <conditions logicalGrouping="MatchAll" trackAllCaptures="false">                         <add input="{REQUEST_FILENAME}" matchType="IsDirectory" negate="true" />                         <add input="{REQUEST_FILENAME}" matchType="IsFile" negate="true" />                         <add input="{URL}" pattern="WebResource.axd" negate="true" />                     </conditions>                     <action type="Redirect" url="{R:1}/" />                 </rule>             </rules>         </rewrite>     </system.webServer> </configuration> Try the Rule Out Now that we’ve saved the rule, let’s try it out on our site.  Try the following two URLs on my site: http://scottgu.com http://scottgu.com/ Notice that the first URL (which has no trailing slash) automatically does a redirect to a URL with the trailing slash.  Because it is a permanent redirect, search engines will follow the URL and update the page ranking. Scenario 4: Canonical Host Names The final SEO problem I discussed earlier are scenarios where a site works with both a leading “www” hostname prefix as well as just the hostname itself.  This causes search engines to treat the URLs as different and split search rankling: http://www.scottgu.com/albums.aspx http://scottgu.com/albums.aspx We can fix this by adding a new IIS Rewrite rule that automatically redirects anyone who navigates to the first URL (that has a www prefix) to instead go to the second URL.  Like before, we will setup the HTTP redirect to be a “permanent redirect” – which will indicate to search engines that they should follow the redirect and use the new URL they are redirected to as the identifier of the content they retrieve.  To create such a rule we’ll click the “Add Rule” link in the URL Rewrite admin tool again.  This will cause the “Add Rule” dialog to appear again: The URL Rewrite admin tool has a built-in “Canonical domain name” rule template.  When we select it and click the “ok” button we’ll see the following dialog which asks us if we want to create a redirect rule that automatically redirects users to a primary host name URL: Above I’m entering the primary URL address I want to expose to the web: scottgu.com.  When we click the “OK” button we’ll get a pre-written rule that automatically performs a permanent redirect if the URL has another leading domain name prefix.  This will save the following additional rule to our web.config file: <configuration>     <system.webServer>         <rewrite>             <rules>                 <rule name="Cannonical Hostname">                     <match url="(.*)" />                     <conditions logicalGrouping="MatchAll" trackAllCaptures="false">                         <add input="{HTTP_HOST}" pattern="^scottgu\.com$" negate="true" />                     </conditions>                     <action type="Redirect" url="http://scottgu.com/{R:1}" />                 </rule>                 <rule name="Default Document" stopProcessing="true">                     <match url="(.*?)/?Default\.aspx$" />                     <action type="Redirect" url="{R:1}/" />                 </rule>                 <rule name="Lower Case URLs" stopProcessing="true">                     <match url="[A-Z]" ignoreCase="false" />                     <conditions logicalGrouping="MatchAll" trackAllCaptures="false">                         <add input="{URL}" pattern="WebResource.axd" negate="true" />                     </conditions>                     <action type="Redirect" url="{ToLower:{URL}}" />                 </rule>                 <rule name="Trailing Slash" stopProcessing="true">                     <match url="(.*[^/])$" />                     <conditions logicalGrouping="MatchAll" trackAllCaptures="false">                         <add input="{REQUEST_FILENAME}" matchType="IsDirectory" negate="true" />                         <add input="{REQUEST_FILENAME}" matchType="IsFile" negate="true" />                         <add input="{URL}" pattern="WebResource.axd" negate="true" />                     </conditions>                     <action type="Redirect" url="{R:1}/" />                 </rule>             </rules>         </rewrite>     </system.webServer> </configuration> Try the Rule Out Now that we’ve saved the rule, let’s try it out on our site.  Try the following two URLs on my site: http://www.scottgu.com/albums.aspx http://scottgu.com/albums.aspx Notice that the first URL (which has the “www” prefix) now automatically does a redirect to the second URL which does not have the www prefix.  Because it is a permanent redirect, search engines will follow the URL and update the page ranking. 4 Simple Rules for Improved SEO The above 4 rules are pretty easy to setup and should take less than 15 minutes to configure on existing sites you already have.  The beauty of using a solution like the URL Rewrite Extension is that you can take advantage of it without having to change code within your web-site – and without having to break any existing links already pointing at your site.  Users who follow existing links will be automatically redirected to the new URLs you wish to publish.  And search engines will start to give your site a higher search relevancy ranking – which will list your site higher in search results and drive more traffic to it. Customizing your URL Rewriting rules further is easy to-do either by editing the web.config file directly, or alternatively, just double click the URL Rewrite icon within the IIS 7.x admin tool and it will list all the active rules for your web-site or application: Clicking any of the rules above will open the rules editor back up and allow you to tweak/customize/save them further. Summary Measuring and improving SEO is something every developer building a public-facing web-site needs to think about and focus on.  If you haven’t already, download and use the SEO Toolkit to analyze the SEO of your sites today. New URL Routing features in ASP.NET MVC and ASP.NET Web Forms 4 make it much easier to build applications that have more control over the URLs that are published.  Tools like the URL Rewrite Extension that I’ve talked about in this blog post make it much easier to improve the URLs that are published from sites you already have built today – without requiring you to change a lot of code. The URL Rewrite Extension provides a bunch of additional great capabilities – far beyond just SEO - as well.  I’ll be covering these additional capabilities more in future blog posts. Hope this helps, Scott

    Read the article

  • Part 2&ndash;Load Testing In The Cloud

    - by Tarun Arora
    Welcome to Part 2, In Part 1 we discussed the advantages of creating a Test Rig in the cloud, the Azure edge and the Test Rig Topology we want to get to. In Part 2, Let’s start by understanding the components of Azure we’ll be making use of followed by manually putting them together to create the test rig, so… let’s get down dirty start setting up the Test Rig.  What Components of Azure will I be using for building the Test Rig in the Cloud? To run the Test Agents we’ll make use of Windows Azure Compute and to enable communication between Test Controller and Test Agents we’ll make use of Windows Azure Connect.  Azure Connect The Test Controller is on premise and the Test Agents are in the cloud (How will they talk?). To enable communication between the two, we’ll make use of Windows Azure Connect. With Windows Azure Connect, you can use a simple user interface to configure IPsec protected connections between computers or virtual machines (VMs) in your organization’s network, and roles running in Windows Azure. With this you can now join Windows Azure role instances to your domain, so that you can use your existing methods for domain authentication, name resolution, or other domain-wide maintenance actions. For more details refer to an overview of Windows Azure connect. A very useful video explaining everything you wanted to know about Windows Azure connect.  Azure Compute Windows Azure compute provides developers a platform to host and manage applications in Microsoft’s data centres across the globe. A Windows Azure application is built from one or more components called ‘roles.’ Roles come in three different types: Web role, Worker role, and Virtual Machine (VM) role, we’ll be using the Worker role to set up the Test Agents. A very nice blog post discussing the difference between the 3 role types. Developers are free to use the .NET framework or other software that runs on Windows with the Worker role or Web role. Developers can also create applications using languages such as PHP and Java. More on Windows Azure Compute. Each Windows Azure compute instance represents a virtual server... Virtual Machine Size CPU Cores Memory Cost Per Hour Extra Small Shared 768 MB $0.04 Small 1 1.75 GB $0.12 Medium 2 3.50 GB $0.24 Large 4 7.00 GB $0.48 Extra Large 8 14.00 GB $0.96   You might want to review the Windows Azure Pricing FAQ. Let’s Get Started building the Test Rig… Configuration Machine Role Comments VM – 1 Domain Controller for Playpit.com On Premise VM – 2 TFS, Test Controller On Premise VM – 3 Test Agent Cloud   In this blog post I would assume that you have the domain, Team Foundation Server and Test Controller Installed and set up already. If not, please refer to the TFS 2010 Installation Guide and this walkthrough on MSDN to set up your Test Controller. You can also download a preconfigured TFS 2010 VM from Brian Keller's blog, Brian also has some great hands on Labs on TFS 2010 that you may want to explore. I. Lets start building VM – 3: The Test Agent Download the Windows Azure SDK and Tools Open Visual Studio and create a new Windows Azure Project using the Cloud Template                   Choose the Worker Role for reasons explained in the earlier post         The WorkerRole.cs implements the Run() and OnStart() methods, no code changes required. You should be able to compile the project and run it in the compute emulator (The compute emulator should have been installed as part of the Windows Azure Toolkit) on your local machine.                   We will only be making changes to WindowsAzureProject, open ServiceDefinition.csdef. Ensure that the vmsize is small (remember the cost chart above). Import the “Connect” module. I am importing the Connect module because I need to join the Worker role VM to the Playpit domain. <?xml version="1.0" encoding="utf-8"?> <ServiceDefinition name="WindowsAzureProject2" xmlns="http://schemas.microsoft.com/ServiceHosting/2008/10/ServiceDefinition"> <WorkerRole name="WorkerRole1" vmsize="Small"> <Imports> <Import moduleName="Diagnostics" /> <Import moduleName="Connect"/> </Imports> </WorkerRole> </ServiceDefinition> Go to the ServiceConfiguration.Cloud.cscfg and note that settings with key ‘Microsoft.WindowsAzure.Plugins.Connect.%%%%’ have been added to the configuration file. This is because you decided to import the connect module. See the config below. <?xml version="1.0" encoding="utf-8"?> <ServiceConfiguration serviceName="WindowsAzureProject2" xmlns="http://schemas.microsoft.com/ServiceHosting/2008/10/ServiceConfiguration" osFamily="1" osVersion="*"> <Role name="WorkerRole1"> <Instances count="1" /> <ConfigurationSettings> <Setting name="Microsoft.WindowsAzure.Plugins.Diagnostics.ConnectionString" value="UseDevelopmentStorage=true" /> <Setting name="Microsoft.WindowsAzure.Plugins.Connect.ActivationToken" value="" /> <Setting name="Microsoft.WindowsAzure.Plugins.Connect.Refresh" value="" /> <Setting name="Microsoft.WindowsAzure.Plugins.Connect.WaitForConnectivity" value="" /> <Setting name="Microsoft.WindowsAzure.Plugins.Connect.Upgrade" value="" /> <Setting name="Microsoft.WindowsAzure.Plugins.Connect.EnableDomainJoin" value="" /> <Setting name="Microsoft.WindowsAzure.Plugins.Connect.DomainFQDN" value="" /> <Setting name="Microsoft.WindowsAzure.Plugins.Connect.DomainControllerFQDN" value="" /> <Setting name="Microsoft.WindowsAzure.Plugins.Connect.DomainAccountName" value="" /> <Setting name="Microsoft.WindowsAzure.Plugins.Connect.DomainPassword" value="" /> <Setting name="Microsoft.WindowsAzure.Plugins.Connect.DomainOU" value="" /> <Setting name="Microsoft.WindowsAzure.Plugins.Connect.Administrators" value="" /> <Setting name="Microsoft.WindowsAzure.Plugins.Connect.DomainSiteName" value="" /> </ConfigurationSettings> </Role> </ServiceConfiguration>             Let’s go step by step and understand all the highlighted parameters and where you can find the values for them.       osFamily – By default this is set to 1 (Windows Server 2008 SP2). Change this to 2 if you want the Windows Server 2008 R2 operating system. The Advantage of using osFamily = “2” is that you get Powershell 2.0 rather than Powershell 1.0. In Powershell 2.0 you could simply use “powershell -ExecutionPolicy Unrestricted ./myscript.ps1” and it will work while in Powershell 1.0 you will have to change the registry key by including the following in your command file “reg add HKLM\Software\Microsoft\PowerShell\1\ShellIds\Microsoft.PowerShell /v ExecutionPolicy /d Unrestricted /f” before you can execute any power shell. The other reason you might want to move to os2 is if you wanted IIS 7.5.       Activation Token – To enable communication between the on premise machine and the Windows Azure Worker role VM both need to have the same token. Log on to Windows Azure Management Portal, click on Connect, click on Get Activation Token, this should give you the activation token, copy the activation token to the clipboard and paste it in the configuration file. Note – Later in the blog I’ll be showing you how to install connect on the on premise machine.                       EnableDomainJoin – Set the value to true, ofcourse we want to join the on windows azure worker role VM to the domain.       DomainFQDN, DomainControllerFQDN, DomainAccountName, DomainPassword, DomainOU, Administrators – This information is specific to your domain. I have extracted this information from the ‘service manager’ and ‘Active Directory Users and Computers’. Also, i created a new Domain-OU namely ‘CloudInstances’ so all my cloud instances joined to my domain show up here, this is optional. You can encrypt the DomainPassword – refer to the instructions here. Or hold fire, I’ll be covering that when i come to certificates and encryption in the coming section.       Now once you have filled all this information up, the configuration file should look something like below, <?xml version="1.0" encoding="utf-8"?> <ServiceConfiguration serviceName="WindowsAzureProject2" xmlns="http://schemas.microsoft.com/ServiceHosting/2008/10/ServiceConfiguration" osFamily="2" osVersion="*"> <Role name="WorkerRole1"> <Instances count="1" /> <ConfigurationSettings> <Setting name="Microsoft.WindowsAzure.Plugins.Diagnostics.ConnectionString" value="UseDevelopmentStorage=true" /> <Setting name="Microsoft.WindowsAzure.Plugins.Connect.ActivationToken" value="45f55fea-f194-4fbc-b36e-25604faac784" /> <Setting name="Microsoft.WindowsAzure.Plugins.Connect.Refresh" value="" /> <Setting name="Microsoft.WindowsAzure.Plugins.Connect.WaitForConnectivity" value="" /> <Setting name="Microsoft.WindowsAzure.Plugins.Connect.Upgrade" value="" /> <Setting name="Microsoft.WindowsAzure.Plugins.Connect.EnableDomainJoin" value="true" /> <Setting name="Microsoft.WindowsAzure.Plugins.Connect.DomainFQDN" value="play.pit.com" /> <Setting name="Microsoft.WindowsAzure.Plugins.Connect.DomainControllerFQDN" value="WIN-KUDQMQFGQOL.play.pit.com" /> <Setting name="Microsoft.WindowsAzure.Plugins.Connect.DomainAccountName" value="playpit\Administrator" /> <Setting name="Microsoft.WindowsAzure.Plugins.Connect.DomainPassword" value="************************" /> <Setting name="Microsoft.WindowsAzure.Plugins.Connect.DomainOU" value="OU=CloudInstances, DC=Play, DC=Pit, DC=com" /> <Setting name="Microsoft.WindowsAzure.Plugins.Connect.Administrators" value="Playpit\Administrator" /> <Setting name="Microsoft.WindowsAzure.Plugins.Connect.DomainSiteName" value="" /> </ConfigurationSettings> </Role> </ServiceConfiguration> Next we will be enabling the Remote Desktop module in to the ServiceDefinition.csdef, we could make changes manually or allow a beautiful wizard to help us make changes. I prefer the second option. So right click on the Windows Azure project and choose Publish       Now once you get the publish wizard, if you haven’t already you would be asked to import your Windows Azure subscription, this is simply the Msdn subscription activation key xml. Once you have done click Next to go to the Settings page and check ‘Enable Remote Desktop for all roles’.       As soon as you do that you get another pop up asking you the details for the user that you would be logging in with (make sure you enter a reasonable expiry date, you do not want the user account to expire today). Notice the more information tag at the bottom, click that to get access to the certificate section. See screen shot below.       From the drop down select the option to create a new certificate        In the pop up window enter the friendly name for your certificate. In my case I entered ‘WAC – Test Rig’ and click ok. This will create a new certificate for you. Click on the view button to see the certificate details. Do you see the Thumbprint, this is the value that will go in the config file (very important). Now click on the Copy to File button to copy the certificate, we will need to import the certificate to the windows Azure Management portal later. So, make sure you save it a safe location.                                Click Finish and enter details of the user you would like to create with permissions for remote desktop access, once you have entered the details on the ‘Remote desktop configuration’ screen click on Ok. From the Publish Windows Azure Wizard screen press Cancel. Cancel because we don’t want to publish the role just yet and Yes because we want to save all the changes in the config file.       Now if you go to the ServiceDefinition.csdef file you will see that the RemoteAccess and RemoteForwarder roles have been imported for you. <?xml version="1.0" encoding="utf-8"?> <ServiceDefinition name="WindowsAzureProject2" xmlns="http://schemas.microsoft.com/ServiceHosting/2008/10/ServiceDefinition"> <WorkerRole name="WorkerRole1" vmsize="Small"> <Imports> <Import moduleName="Diagnostics" /> <Import moduleName="Connect" /> <Import moduleName="RemoteAccess" /> <Import moduleName="RemoteForwarder" /> </Imports> </WorkerRole> </ServiceDefinition> Now go to the ServiceConfiguration.Cloud.cscfg file and you see a whole bunch for setting “Microsoft.WindowsAzure.Plugins.RemoteAccess.%%%” values added for you. <?xml version="1.0" encoding="utf-8"?> <ServiceConfiguration serviceName="WindowsAzureProject2" xmlns="http://schemas.microsoft.com/ServiceHosting/2008/10/ServiceConfiguration" osFamily="2" osVersion="*"> <Role name="WorkerRole1"> <Instances count="1" /> <ConfigurationSettings> <Setting name="Microsoft.WindowsAzure.Plugins.Diagnostics.ConnectionString" value="UseDevelopmentStorage=true" /> <Setting name="Microsoft.WindowsAzure.Plugins.Connect.ActivationToken" value="45f55fea-f194-4fbc-b36e-25604faac784" /> <Setting name="Microsoft.WindowsAzure.Plugins.Connect.Refresh" value="" /> <Setting name="Microsoft.WindowsAzure.Plugins.Connect.WaitForConnectivity" value="" /> <Setting name="Microsoft.WindowsAzure.Plugins.Connect.Upgrade" value="" /> <Setting name="Microsoft.WindowsAzure.Plugins.Connect.EnableDomainJoin" value="true" /> <Setting name="Microsoft.WindowsAzure.Plugins.Connect.DomainFQDN" value="play.pit.com" /> <Setting name="Microsoft.WindowsAzure.Plugins.Connect.DomainControllerFQDN" value="WIN-KUDQMQFGQOL.play.pit.com" /> <Setting name="Microsoft.WindowsAzure.Plugins.Connect.DomainAccountName" value="playpit\Administrator" /> <Setting name="Microsoft.WindowsAzure.Plugins.Connect.DomainPassword" value="************************" /> <Setting name="Microsoft.WindowsAzure.Plugins.Connect.DomainOU" value="OU=CloudInstances, DC=Play, DC=Pit, DC=com" /> <Setting name="Microsoft.WindowsAzure.Plugins.Connect.Administrators" value="Playpit\Administrator" /> <Setting name="Microsoft.WindowsAzure.Plugins.Connect.DomainSiteName" value="" /> <Setting name="Microsoft.WindowsAzure.Plugins.RemoteAccess.Enabled" value="true" /> <Setting name="Microsoft.WindowsAzure.Plugins.RemoteAccess.AccountUsername" value="Administrator" /> <Setting name="Microsoft.WindowsAzure.Plugins.RemoteAccess.AccountEncryptedPassword" value="MIIBnQYJKoZIhvcNAQcDoIIBjjCCAYoCAQAxggFOMIIBSgIBADAyMB4xHDAaBgNVBAMME1dpbmRvd 3MgQXp1cmUgVG9vbHMCEGa+B46voeO5T305N7TSG9QwDQYJKoZIhvcNAQEBBQAEggEABg4ol5Xol66Ip6QKLbAPWdmD4ae ADZ7aKj6fg4D+ATr0DXBllZHG5Umwf+84Sj2nsPeCyrg3ZDQuxrfhSbdnJwuChKV6ukXdGjX0hlowJu/4dfH4jTJC7sBWS AKaEFU7CxvqYEAL1Hf9VPL5fW6HZVmq1z+qmm4ecGKSTOJ20Fptb463wcXgR8CWGa+1w9xqJ7UmmfGeGeCHQ4QGW0IDSBU6ccg vzF2ug8/FY60K1vrWaCYOhKkxD3YBs8U9X/kOB0yQm2Git0d5tFlIPCBT2AC57bgsAYncXfHvPesI0qs7VZyghk8LVa9g5IqaM Cp6cQ7rmY/dLsKBMkDcdBHuCTAzBgkqhkiG9w0BBwEwFAYIKoZIhvcNAwcECDRVifSXbA43gBApNrp40L1VTVZ1iGag+3O1" /> <Setting name="Microsoft.WindowsAzure.Plugins.RemoteAccess.AccountExpiration" value="2012-11-27T23:59:59.0000000+00:00" /> <Setting name="Microsoft.WindowsAzure.Plugins.RemoteForwarder.Enabled" value="true" /> </ConfigurationSettings> <Certificates> <Certificate name="Microsoft.WindowsAzure.Plugins.RemoteAccess.PasswordEncryption" thumbprint="AA23016CF0BDFC344400B5B82706B608B92E4217" thumbprintAlgorithm="sha1" /> </Certificates> </Role> </ServiceConfiguration>          Okay let’s look at them one at a time,       Enabled - Yes, we would like to enable Remote Access.       AccountUserName – This is the user name you entered while you were on the publish windows azure role screen, as detailed above.       AccountEncrytedPassword – Try and decode that, the certificate is used to encrypt the password you specified for the user account. Remember earlier i said, either use the instructions or wait and i’ll be showing you encryption, now the user account i am using for rdp has the same password as my domain password, so i can simply copy the value of the AccountEncryptedPassword to the DomainPassword as well.       AccountExpiration – This is the expiration as you specified in the wizard earlier, make sure your account does not expire today.       Remote Forwarder – Check out the documentation, below is how I understand it, -- One role in an application that implements a remote desktop connection must import the RemoteForwarder module. The two modules work together to enable the remote desktop connections to role instances. -- If you have multiple roles defined in the service model, it does not matter which role you add the RemoteForwarder module to, but you must add it to only one of the role definitions.       Certificate – Remember the certificate thumbprint from the wizard, the on premise machine and windows azure role machine that need to speak to each other must have the same thumbprint. More on that when we install Windows Azure connect Endpoints on the on premise machine. As i said earlier, in this blog post, I’ll be showing you the manual process so i won’t be scripting any star up tasks to install the test agent or register the test agent with the TFS Server. I’ll be showing you all this cool stuff in the next blog post, that’s because it’s important to understand the manual side of it, it becomes easier for you to troubleshoot in case something fails. Having said that, the changes we have made are sufficient to spin up the Windows Azure Worker Role aka Test Agent VM, have it connected with the play.pit.com domain and have remote access enabled on it. Before we deploy the Test Agent VM we need to set up Windows Azure Connect on the TFS Server. II. Windows Azure Connect: Setting up Connect on VM – 2 i.e. TFS & Test Controller Glad you made it so far, now to enable communication between the on premise TFS/Test Controller and Azure-ed Test Agent we need to enable communication. We have set up the Azure connect module in the Test Agent configuration, now the connect end points need to be enabled on the on premise machines, let’s have a look at how we can do this. Log on to VM – 2 running the TFS Server and Test Controller Log on to the Windows Azure Management Portal and click on Virtual Network Click on Virtual Network, if you already have a subscription you should see the below screen shot, if not, you would be asked to complete the subscription first        Click on Install Local Endpoints from the top left on the panel and you get a url appended with a token id in it, remember the token i showed you earlier, in theory the token you get here should match the token you added to the Test Agent config file.        Copy the url to the clip board and paste it in IE explorer (important, the installation at present only works out of IE and you need to have cookies enabled in order to complete the installation). As stated in the pop up, you can NOT download and run the software later, you need to run it as is, since it contains a token. Once the installation completes you should see the Windows Azure connect icon in the system tray.                         Right click the Azure Connect icon, choose Diagnostics and refer to this link for diagnostic detail terminology. NOTE – Unfortunately I could not see the Windows Azure connect icon in the system tray, a bit of binging with Google revealed that the azure connect icon is only shown when the ‘Windows Azure Connect Endpoint’ Service is started. So go to services.msc and make sure that the service is started, if not start it, unfortunately again, the service did not start for me on a manual start and i realised that one of the dependant services was disabled, you can look at the service dependencies and start them and then start windows azure connect. Bottom line, you need to start Windows Azure connect service before you can proceed. Please refer here on MSDN for more on Troubleshooting Windows Azure connect. (Follow the next step as well)   Now go back to the Windows Azure Management Portal and from Groups and Roles create a new group, lets call it ‘Test Rig’. Make sure you add the VM – 2 (the TFS Server VM where you just installed the endpoint).       Now if you go back to the Azure Connect icon in the system tray and click ‘Refresh Policy’ you will notice that the disconnected status of the icon should change to ready for connection. III. Importing Certificate in to Windows Azure Management Portal But before that you need to import the certificate you created in Step I in to the Windows Azure Management Portal. Log on to the Windows Azure Management Portal and click on ‘Hosted Services, Storage Accounts & CDN’ and then ‘Management Certificates’ followed by Add Certificates as shown in the screen shot below        Browse to the location where you saved the certificate earlier, remember… Refer to Step I in case you forgot.        Now you should be able to see the imported certificate here, make sure the thumbprint of the certificate matches the one you inserted in the config files        IV. Publish Windows Azure Worker Role aka Test Agent Having completed I, II and III, you are ready to publish the Test Agent VM – 3 to the cloud. Go to Visual Studio and right click the Windows Azure project and select Publish. Verify the infomration in the wizard, from the advanced settings tab, you can also enabled capture of intellitrace or profiling information.         Click Next and Click Publish! From the view menu bar select the Windows Azure Activity Log window.       Now you should be able to see the deployment progress in real time.             In the Windows Azure Management Portal, you should also be able to see the progress of creation of a new Worker Role.       Once the deployment is complete you should be able to RDP (go to run prompt type mstsc and in the pop up the machine name) in to the Test Agent Worker Role VM from the Playpit network using the domain admin user account. In case you are unable to log in to the Test Agent using the domain admin user account it means the process of joining the Test Agent to the domain has failed! But the good news is, because you imported the connect module, you can connect to the Test Agent machine using Windows Azure Management Portal and troubleshoot the reason for failure, you will be able to log in with the user name and password you specified in the config file for the keys ‘RemoteAccess.AccountUsername, RemoteAccess.EncryptedPassword (just that enter the password unencrypted)’, fix it or manually join the machine to the domain. Once you have managed to Join the Test Agent VM to the Domain move to the next step.      So, log in to the Test Agent Worker Role VM with the Playpit Domain Administrator and verify that you can log in, the machine is connected to the domain and the connect service is successfully running. If yes, give your self a pat on the back, you are 80% mission accomplished!         Go to the Windows Azure Management Portal and click on Virtual Network, click on Groups and Roles and click on Test Rig, click Edit Group, the edit the Test Rig group you created earlier. In the Connect to section, click on Add to select the worker role you have just deployed. Also, check the ‘Allow connections between endpoints in the group’ with this you will enable to communication between test controller and test agents and test agents/test agents. Click Save.      Now, you are ready to deploy the Test Agent software on the Worker Role Test Agent VM and configure it to work with the Test Controller. V. Configuring VM – 3: Installing Test Agent and Associating Test Agent to Controller Log in to the Worker Role Test Agent VM that you have just successfully deployed, make sure you log in with the domain administrator account. Download the All Agents software from MSDN, ‘en_visual_studio_agents_2010_x86_x64_dvd_509679.iso’, extract the iso and navigate to where you have extracted the iso. In my case, i have extracted the iso to “C:\Resources\Temp\VsAgentSetup”. Open the Test Agent folder and double click on setup.exe. Once you have installed the Test Agent you should reach the configuration window. If you face any issues installing TFS Test Agent on the VM, refer to the walkthrough on MSDN.       Once you have successfully installed the Test Agent software you will need to configure the test agent. Right click the test agent configuration tool and run as a different user. i.e. an Administrator. This is really to run the configuration wizard with elevated privileges (you might have UAC block something's otherwise).        In the run options, you can select ‘service’ you do not need to run the agent as interactive un less you are running coded UI tests. I have specified the domain administrator to connect to the TFS Test Controller. In real life, i would never do that, i would create a separate test user service account for this purpose. But for the blog post, we are using the most powerful user so that any policies or restrictions don’t block you.        Click the Apply Settings button and you should be all green! If not, the summary usually gives helpful error messages that you can resolve and proceed. As per my experience, you may run in to either a permission or a firewall blocking communication issue.        And now the moment of truth! Go to VM –2 open up Visual Studio and from the Test Menu select Manage Test Controller       Mission Accomplished! You should be able to see the Test Agent that you have just configured here,         VI. Creating and Running Load Tests on your brand new Azure-ed Test Rig I have various blog posts on Performance Testing with Visual Studio Ultimate, you can follow the links and videos below, Blog Posts: - Part 1 – Performance Testing using Visual Studio 2010 Ultimate - Part 2 – Performance Testing using Visual Studio 2010 Ultimate - Part 3 – Performance Testing using Visual Studio 2010 Ultimate Videos: - Test Tools Configuration & Settings in Visual Studio - Why & How to Record Web Performance Tests in Visual Studio Ultimate - Goal Driven Load Testing using Visual Studio Ultimate Now that you have created your load tests, there is one last change you need to make before you can run the tests on your Azure Test Rig, create a new Test settings file, and change the Test Execution method to ‘Remote Execution’ and select the test controller you have configured the Worker Role Test Agent against in our case VM – 2 So, go on, fire off a test run and see the results of the test being executed on the Azur-ed Test Rig. Review and What’s next? A quick recap of the benefits of running the Test Rig in the cloud and what i will be covering in the next blog post AND I would love to hear your feedback! Advantages Utilizing the power of Azure compute to run a heavy virtual user load. Benefiting from the Azure flexibility, destroy Test Agents when not in use, takes < 25 minutes to spin up a new Test Agent. Most important test Network Latency, (network latency and speed of connection are two different things – usually network latency is very hard to test), by placing the Test Agents in Microsoft Data centres around the globe, one can actually test the lag in transferring the bytes not because of a slow connection but because the page has been requested from the other side of the globe. Next Steps The process of spinning up the Test Agents in windows Azure is not 100% automated. I am working on the Worker process and power shell scripts to make the role deployment, unattended install of test agent software and registration of the test agent to the test controller automated. In the next blog post I will show you how to make the complete process unattended and automated. Remember to subscribe to http://feeds.feedburner.com/TarunArora. Hope you enjoyed this post, I would love to hear your feedback! If you have any recommendations on things that I should consider or any questions or feedback, feel free to leave a comment. See you in Part III.   Share this post : CodeProject

    Read the article

  • FreeBSD performance tuning. Sysctls, loader.conf, kernel

    - by SaveTheRbtz
    I wanted to share knowledge of tuning FreeBSD via sysctl.conf/loader.conf/KENCONF. It was initially based on Igor Sysoev's (author of nginx) presentation about FreeBSD tuning up to 100,000-200,000 active connections. Tunings are for FreeBSD-CURRENT. Since 7.2 amd64 some of them are tuned well by default. Prior 7.0 some of them are boot only (set via /boot/loader.conf) or does not exist at all. sysctl.conf: # No zero mapping feature # May break wine # (There are also reports about broken samba3) #security.bsd.map_at_zero=0 # If you have really busy webserver with apache13 you may run out of processes #kern.maxproc=10000 # Same for servers with apache2 / Pound #kern.threads.max_threads_per_proc=4096 # Max. backlog size kern.ipc.somaxconn=4096 # Shared memory // 7.2+ can use shared memory > 2Gb kern.ipc.shmmax=2147483648 # Sockets kern.ipc.maxsockets=204800 # Can cause this on older kernels: # http://old.nabble.com/Significant-performance-regression-for-increased-maxsockbuf-on-8.0-RELEASE-tt26745981.html#a26745981 ) kern.ipc.maxsockbuf=10485760 # Mbuf 2k clusters (on amd64 7.2+ 25600 is default) # For such high value vm.kmem_size must be increased to 3G kern.ipc.nmbclusters=262144 # Jumbo pagesize(_SC_PAGESIZE) clusters # Used as general packet storage for jumbo frames # can be monitored via `netstat -m` #kern.ipc.nmbjumbop=262144 # Jumbo 9k/16k clusters # If you are using them #kern.ipc.nmbjumbo9=65536 #kern.ipc.nmbjumbo16=32768 # For lower latency you can decrease scheduler's maximum time slice # default: stathz/10 (~ 13) #kern.sched.slice=1 # Increase max command-line length showed in `ps` (e.g for Tomcat/Java) # Default is PAGE_SIZE / 16 or 256 on x86 # This avoids commands to be presented as [executable] in `ps` # For more info see: http://www.freebsd.org/cgi/query-pr.cgi?pr=120749 kern.ps_arg_cache_limit=4096 # Every socket is a file, so increase them kern.maxfiles=204800 kern.maxfilesperproc=200000 kern.maxvnodes=200000 # On some systems HPET is almost 2 times faster than default ACPI-fast # Useful on systems with lots of clock_gettime / gettimeofday calls # See http://old.nabble.com/ACPI-fast-default-timecounter,-but-HPET-83--faster-td23248172.html # After revision 222222 HPET became default: http://svnweb.freebsd.org/base?view=revision&revision=222222 kern.timecounter.hardware=HPET # Small receive space, only usable on http-server, on file server this # should be increased to 65535 or even more #net.inet.tcp.recvspace=8192 # This is useful on Fat-Long-Pipes #net.inet.tcp.recvbuf_max=10485760 #net.inet.tcp.recvbuf_inc=65535 # Small send space is useful for http servers that serve small files # Autotuned since 7.x net.inet.tcp.sendspace=16384 # This is useful on Fat-Long-Pipes #net.inet.tcp.sendbuf_max=10485760 #net.inet.tcp.sendbuf_inc=65535 # Turn off receive autotuning # You can play with it. #net.inet.tcp.recvbuf_auto=0 #net.inet.tcp.sendbuf_auto=0 # This should be enabled if you going to use big spaces (>64k) # Also timestamp field is useful when using syncookies net.inet.tcp.rfc1323=1 # Turn this off on high-speed, lossless connections (LAN 1Gbit+) # If you set it there is no need in TCP_NODELAY sockopt (see man tcp) net.inet.tcp.delayed_ack=0 # This feature is useful if you are serving data over modems, Gigabit Ethernet, # or even high speed WAN links (or any other link with a high bandwidth delay product), # especially if you are also using window scaling or have configured a large send window. # Automatically disables on small RTT ( http://www.freebsd.org/cgi/cvsweb.cgi/src/sys/netinet/tcp_subr.c?#rev1.237 ) # This sysctl was removed in 10-CURRENT: # See: http://www.mail-archive.com/[email protected]/msg06178.html #net.inet.tcp.inflight.enable=0 # TCP slowstart algorithm tunings # We assuming we have very fast clients #net.inet.tcp.slowstart_flightsize=100 #net.inet.tcp.local_slowstart_flightsize=100 # Disable randomizing of ports to avoid false RST # Before usage check SA here www.bsdcan.org/2006/papers/ImprovingTCPIP.pdf # (it's also says that port randomization auto-disables at some conn.rates, but I didn't checked it thou) #net.inet.ip.portrange.randomized=0 # Increase portrange # For outgoing connections only. Good for seed-boxes and ftp servers. net.inet.ip.portrange.first=1024 net.inet.ip.portrange.last=65535 # # stops route cache degregation during a high-bandwidth flood # http://www.freebsd.org/doc/en/books/handbook/securing-freebsd.html #net.inet.ip.rtexpire=2 net.inet.ip.rtminexpire=2 net.inet.ip.rtmaxcache=1024 # Security net.inet.ip.redirect=0 net.inet.ip.sourceroute=0 net.inet.ip.accept_sourceroute=0 net.inet.icmp.maskrepl=0 net.inet.icmp.log_redirect=0 net.inet.icmp.drop_redirect=1 net.inet.tcp.drop_synfin=1 # # There is also good example of sysctl.conf with comments: # http://www.thern.org/projects/sysctl.conf # # icmp may NOT rst, helpful for those pesky spoofed # icmp/udp floods that end up taking up your outgoing # bandwidth/ifqueue due to all that outgoing RST traffic. # #net.inet.tcp.icmp_may_rst=0 # Security net.inet.udp.blackhole=1 net.inet.tcp.blackhole=2 # IPv6 Security # For more info see http://www.fosslc.org/drupal/content/security-implications-ipv6 # Disable Node info replies # To see this vulnerability in action run `ping6 -a sglAac ::1` or `ping6 -w ::1` on unprotected node net.inet6.icmp6.nodeinfo=0 # Turn on IPv6 privacy extensions # For more info see proposal http://unix.derkeiler.com/Mailing-Lists/FreeBSD/net/2008-06/msg00103.html net.inet6.ip6.use_tempaddr=1 net.inet6.ip6.prefer_tempaddr=1 # Disable ICMP redirect net.inet6.icmp6.rediraccept=0 # Disable acceptation of RA and auto linklocal generation if you don't use them #net.inet6.ip6.accept_rtadv=0 #net.inet6.ip6.auto_linklocal=0 # Increases default TTL, sometimes useful # Default is 64 net.inet.ip.ttl=128 # Lessen max segment life to conserve resources # ACK waiting time in miliseconds # (default: 30000. RFC from 1979 recommends 120000) net.inet.tcp.msl=5000 # Max bumber of timewait sockets net.inet.tcp.maxtcptw=200000 # Don't use tw on local connections # As of 15 Apr 2009. Igor Sysoev says that nolocaltimewait has some buggy realization. # So disable it or now till get fixed #net.inet.tcp.nolocaltimewait=1 # FIN_WAIT_2 state fast recycle net.inet.tcp.fast_finwait2_recycle=1 # Time before tcp keepalive probe is sent # default is 2 hours (7200000) #net.inet.tcp.keepidle=60000 # Should be increased until net.inet.ip.intr_queue_drops is zero net.inet.ip.intr_queue_maxlen=4096 # Interrupt handling via multiple CPU, but with context switch. # You can play with it. Default is 1; #net.isr.direct=0 # This is for routers only #net.inet.ip.forwarding=1 #net.inet.ip.fastforwarding=1 # This speed ups dummynet when channel isn't saturated net.inet.ip.dummynet.io_fast=1 # Increase dummynet(4) hash #net.inet.ip.dummynet.hash_size=2048 #net.inet.ip.dummynet.max_chain_len # Should be increased when you have A LOT of files on server # (Increase until vfs.ufs.dirhash_mem becomes lower) vfs.ufs.dirhash_maxmem=67108864 # Note from commit http://svn.freebsd.org/base/head@211031 : # For systems with RAID volumes and/or virtualization envirnments, where # read performance is very important, increasing this sysctl tunable to 32 # or even more will demonstratively yield additional performance benefits. vfs.read_max=32 # Explicit Congestion Notification (see http://en.wikipedia.org/wiki/Explicit_Congestion_Notification) net.inet.tcp.ecn.enable=1 # Flowtable - flow caching mechanism # Useful for routers #net.inet.flowtable.enable=1 #net.inet.flowtable.nmbflows=65535 # Extreme polling tuning #kern.polling.burst_max=1000 #kern.polling.each_burst=1000 #kern.polling.reg_frac=100 #kern.polling.user_frac=1 #kern.polling.idle_poll=0 # IPFW dynamic rules and timeouts tuning # Increase dyn_buckets till net.inet.ip.fw.curr_dyn_buckets is lower net.inet.ip.fw.dyn_buckets=65536 net.inet.ip.fw.dyn_max=65536 net.inet.ip.fw.dyn_ack_lifetime=120 net.inet.ip.fw.dyn_syn_lifetime=10 net.inet.ip.fw.dyn_fin_lifetime=2 net.inet.ip.fw.dyn_short_lifetime=10 # Make packets pass firewall only once when using dummynet # i.e. packets going thru pipe are passing out from firewall with accept #net.inet.ip.fw.one_pass=1 # shm_use_phys Wires all shared pages, making them unswappable # Use this to lessen Virtual Memory Manager's work when using Shared Mem. # Useful for databases #kern.ipc.shm_use_phys=1 # ZFS # Enable prefetch. Useful for sequential load type i.e fileserver. # FreeBSD sets vfs.zfs.prefetch_disable to 1 on any i386 systems and # on any amd64 systems with less than 4GB of avaiable memory # For additional info check this nabble thread http://old.nabble.com/Samba-read-speed-performance-tuning-td27964534.html #vfs.zfs.prefetch_disable=0 # On highload servers you may notice following message in dmesg: # "Approaching the limit on PV entries, consider increasing either the # vm.pmap.shpgperproc or the vm.pmap.pv_entry_max tunable" vm.pmap.shpgperproc=2048 loader.conf: # Accept filters for data, http and DNS requests # Useful when your software uses select() instead of kevent/kqueue or when you under DDoS # DNS accf available on 8.0+ accf_data_load="YES" accf_http_load="YES" accf_dns_load="YES" # Async IO system calls aio_load="YES" # Linux specific devices in /dev # As for 8.1 it only /dev/full #lindev_load="YES" # Adds NCQ support in FreeBSD # WARNING! all ad[0-9]+ devices will be renamed to ada[0-9]+ # 8.0+ only #ahci_load="YES" #siis_load="YES" # FreeBSD 8.2+ # New Congestion Control for FreeBSD # http://caia.swin.edu.au/urp/newtcp/tools/cc_chd-readme-0.1.txt # http://www.ietf.org/proceedings/78/slides/iccrg-5.pdf # Initial merge commit message http://www.mail-archive.com/[email protected]/msg31410.html #cc_chd_load="YES" # Increase kernel memory size to 3G. # # Use ONLY if you have KVA_PAGES in kernel configuration, and you have more than 3G RAM # Otherwise panic will happen on next reboot! # # It's required for high buffer sizes: kern.ipc.nmbjumbop, kern.ipc.nmbclusters, etc # Useful on highload stateful firewalls, proxies or ZFS fileservers # (FreeBSD 7.2+ amd64 users: Check that current value is lower!) #vm.kmem_size="3G" # If your server has lots of swap (>4Gb) you should increase following value # according to http://lists.freebsd.org/pipermail/freebsd-hackers/2009-October/029616.html # Otherwise you'll be getting errors # "kernel: swap zone exhausted, increase kern.maxswzone" # kern.maxswzone="256M" # Older versions of FreeBSD can't tune maxfiles on the fly #kern.maxfiles="200000" # Useful for databases # Sets maximum data size to 1G # (FreeBSD 7.2+ amd64 users: Check that current value is lower!) #kern.maxdsiz="1G" # Maximum buffer size(vfs.maxbufspace) # You can check current one via vfs.bufspace # Should be lowered/upped depending on server's load-type # Usually decreased to preserve kmem # (default is 10% of mem) #kern.maxbcache="512M" # Sendfile buffers # For i386 only #kern.ipc.nsfbufs=10240 # FreeBSD 9+ # HPET "legacy route" support. It should allow HPET to work per-CPU # See http://www.mail-archive.com/[email protected]/msg03603.html #hint.atrtc.0.clock=0 #hint.attimer.0.clock=0 #hint.hpet.0.legacy_route=1 # syncache Hash table tuning net.inet.tcp.syncache.hashsize=1024 net.inet.tcp.syncache.bucketlimit=512 net.inet.tcp.syncache.cachelimit=65536 # Increased hostcache # Later host cache can be viewed via net.inet.tcp.hostcache.list hidden sysctl # Very useful for it's RTT RTTVAR # Must be power of two net.inet.tcp.hostcache.hashsize=65536 # hashsize * bucketlimit (which is 30 by default) # It allocates 255Mb (1966080*136) of RAM net.inet.tcp.hostcache.cachelimit=1966080 # TCP control-block Hash table tuning net.inet.tcp.tcbhashsize=4096 # Disable ipfw deny all # Should be uncommented when there is a chance that # kernel and ipfw binary may be out-of sync on next reboot #net.inet.ip.fw.default_to_accept=1 # # SIFTR (Statistical Information For TCP Research) is a kernel module that # logs a range of statistics on active TCP connections to a log file. # See prerelease notes http://groups.google.com/group/mailing.freebsd.current/browse_thread/thread/b4c18be6cdce76e4 # and man 4 sitfr #siftr_load="YES" # Enable superpages, for 7.2+ only # Also read http://lists.freebsd.org/pipermail/freebsd-hackers/2009-November/030094.html vm.pmap.pg_ps_enabled=1 # Usefull if you are using Intel-Gigabit NIC #hw.em.rxd=4096 #hw.em.txd=4096 #hw.em.rx_process_limit="-1" # Also if you have ALOT interrupts on NIC - play with following parameters # NOTE: You should set them for every NIC #dev.em.0.rx_int_delay: 250 #dev.em.0.tx_int_delay: 250 #dev.em.0.rx_abs_int_delay: 250 #dev.em.0.tx_abs_int_delay: 250 # There is also multithreaded version of em/igb drivers can be found here: # http://people.yandex-team.ru/~wawa/ # # for additional em monitoring and statistics use # sysctl dev.em.0.stats=1 ; dmesg # sysctl dev.em.0.debug=1 ; dmesg # Also after r209242 (-CURRENT) there is a separate sysctl for each stat variable; # Same tunings for igb #hw.igb.rxd=4096 #hw.igb.txd=4096 #hw.igb.rx_process_limit=100 # Some useful netisr tunables. See sysctl net.isr #net.isr.maxthreads=4 #net.isr.defaultqlimit=4096 #net.isr.maxqlimit: 10240 # Bind netisr threads to CPUs #net.isr.bindthreads=1 # # FreeBSD 9.x+ # Increase interface send queue length # See commit message http://svn.freebsd.org/viewvc/base?view=revision&revision=207554 #net.link.ifqmaxlen=1024 # Nicer boot logo =) loader_logo="beastie" And finally here is KERNCONF: # Just some of them, see also # cat /sys/{i386,amd64,}/conf/NOTES # This one useful only on i386 #options KVA_PAGES=512 # You can play with HZ in environments with high interrupt rate (default is 1000) # 100 is for my notebook to prolong it's battery life #options HZ=100 # Polling is goot on network loads with high packet rates and low-end NICs # NB! Do not enable it if you want more than one netisr thread #options DEVICE_POLLING # Eliminate datacopy on socket read-write # To take advantage with zero copy sockets you should have an MTU >= 4k # This req. is only for receiving data. # Read more in man zero_copy_sockets # Also this epic thread on kernel trap: # http://kerneltrap.org/node/6506 # Here Linus says that "anybody that does it that way (FreeBSD) is totally incompetent" #options ZERO_COPY_SOCKETS # Support TCP sign. Used for IPSec options TCP_SIGNATURE # There was stackoverflow found in KAME IPSec stack: # See http://secunia.com/advisories/43995/ # For quick workaround you can use `ipfw add deny proto ipcomp` options IPSEC # This ones can be loaded as modules. They described in loader.conf section #options ACCEPT_FILTER_DATA #options ACCEPT_FILTER_HTTP # Adding ipfw, also can be loaded as modules options IPFIREWALL # On 8.1+ you can disable verbose to see blocked packets on ipfw0 interface. # Also there is no point in compiling verbose into the kernel, because # now there is net.inet.ip.fw.verbose tunable. #options IPFIREWALL_VERBOSE #options IPFIREWALL_VERBOSE_LIMIT=10 options IPFIREWALL_FORWARD # Adding kernel NAT options IPFIREWALL_NAT options LIBALIAS # Traffic shaping options DUMMYNET # Divert, i.e. for userspace NAT options IPDIVERT # This is for OpenBSD's pf firewall device pf device pflog # pf's QoS - ALTQ options ALTQ options ALTQ_CBQ # Class Bases Queuing (CBQ) options ALTQ_RED # Random Early Detection (RED) options ALTQ_RIO # RED In/Out options ALTQ_HFSC # Hierarchical Packet Scheduler (HFSC) options ALTQ_PRIQ # Priority Queuing (PRIQ) options ALTQ_NOPCC # Required for SMP build # Pretty console # Manual can be found here http://forums.freebsd.org/showthread.php?t=6134 #options VESA #options SC_PIXEL_MODE # Disable reboot on Ctrl Alt Del #options SC_DISABLE_REBOOT # Change normal|kernel messages color options SC_NORM_ATTR=(FG_GREEN|BG_BLACK) options SC_KERNEL_CONS_ATTR=(FG_YELLOW|BG_BLACK) # More scroll space options SC_HISTORY_SIZE=8192 # Adding hardware crypto device device crypto device cryptodev # Useful network interfaces device vlan device tap #Virtual Ethernet driver device gre #IP over IP tunneling device if_bridge #Bridge interface device pfsync #synchronization interface for PF device carp #Common Address Redundancy Protocol device enc #IPsec interface device lagg #Link aggregation interface device stf #IPv4-IPv6 port # Also for my notebook, but may be used with Opteron device amdtemp # Same for Intel processors device coretemp # man 4 cpuctl device cpuctl # CPU control pseudo-device # Support for ECMP. More than one route for destination # Works even with default route so one can use it as LB for two ISP # For now code is unstable and panics (panic: rtfree 2) on route deletions. #options RADIX_MPATH # Multicast routing #options MROUTING #options PIM # Debug & DTrace options KDB # Kernel debugger related code options KDB_TRACE # Print a stack trace for a panic options KDTRACE_FRAME # amd64-only(?) options KDTRACE_HOOKS # all architectures - enable general DTrace hooks #options DDB #options DDB_CTF # all architectures - kernel ELF linker loads CTF data # Adaptive spining in lockmgr (8.x+) # See http://www.mail-archive.com/[email protected]/msg10782.html options ADAPTIVE_LOCKMGRS # UTF-8 in console (8.x+) #options TEKEN_UTF8 # FreeBSD 8.1+ # Deadlock resolver thread # For additional information see http://www.mail-archive.com/[email protected]/msg18124.html # (FYI: "resolution" is panic so use with caution) #options DEADLKRES # Increase maximum size of Raw I/O and sendfile(2) readahead #options MAXPHYS=(1024*1024) #options MAXBSIZE=(1024*1024) # For scheduler debug enable following option. # Debug will be available via `kern.sched.stats` sysctl # For more information see http://svnweb.freebsd.org/base/head/sys/conf/NOTES?view=markup #options SCHED_STATS If you are tuning network for maximum performance you may wish to play with ifconfig options like: # You can list all capabilities via `ifconfig -m` ifconfig [-]rxcsum [-]txcsum [-]tso [-]lro mtu In case you've enabled DDB in kernel config, you should edit your /etc/ddb.conf and add something like this to enable automatic reboot (and textdump as bonus): script kdb.enter.panic=textdump set; capture on; show pcpu; bt; ps; alltrace; capture off; call doadump; reset script kdb.enter.default=textdump set; capture on; bt; ps; capture off; call doadump; reset And do not forget to add ddb_enable="YES" to /etc/rc.conf Since FreeBSD 9 you can select to enable/disable flowcontrol on your NIC: # See http://en.wikipedia.org/wiki/Ethernet_flow_control and # http://www.mail-archive.com/[email protected]/msg07927.html for additional info ifconfig bge0 media auto mediaopt flowcontrol PS. Also most of FreeBSD's limits can be monitored by # vmstat -z and # limits PPS. variety of network counters can be monitored via # netstat -s In FreeBSD-9 netstat's -Q option appeared, try following command to display netisr stats # netstat -Q PPPS. also see # man 7 tuning PPPPS. I wanted to thank FreeBSD community, especially author of nginx - Igor Sysoev, nginx-ru@ and FreeBSD-performance@ mailing lists for providing useful information about FreeBSD tuning. FreeBSD WIP * Whats cooking for FreeBSD 7? * Whats cooking for FreeBSD 8? * Whats cooking for FreeBSD 9? So here is the question: What tunings are you using on yours FreeBSD servers? You can also post your /etc/sysctl.conf, /boot/loader.conf, kernel options, etc with description of its' meaning (do not copy-paste from sysctl -d). Don't forget to specify server type (web, smb, gateway, etc) Let's share experience!

    Read the article

  • DHCP settings out of range Internet shuts off after a few minutes

    - by user263115
    I recently upgraded from windows eight to windows 8.1 I do not know if this has anything to do with anything I have a 64 bit OS. My Internet goes off by itself every 5 minutes even though my wireless icon at the lower right of the screen still shows connected I had an error message in the last event in it said that might DHCP settings were out of range. I get my internet at my house through a wireless portable hotspot through my smart phone. But i haven't ever had any problems before and i only have this problem on this network. If i turn airplane mode on and reset my network card, the internet will come back to life but soon die. i don't experience this problem while on a different network or if i'm on WiFi. This s really annoying please help Windows IP Configuration Host Name . . . . . . . . . . . . : NastyMcnastyJr Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No Ethernet adapter Local Area Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : TeamViewer VPN Adapter Physical Address. . . . . . . . . : 00-FF-5D-13-26-21 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Wireless LAN adapter Local Area Connection* 11: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Microsoft Wi-Fi Direct Virtual Adapter Physical Address. . . . . . . . . : F6-B7-E2-50-09-38 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Wireless LAN adapter SAMMY McNASTY: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Broadcom 802.11n Network Adapter Physical Address. . . . . . . . . : F4-B7-E2-50-09-38 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::3107:66bc:cf1f:c776%4(Preferred) IPv4 Address. . . . . . . . . . . : 192.168.43.3(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : Friday, November 1, 2013 9:50:20 PM Lease Expires . . . . . . . . . . : Saturday, November 2, 2013 12:56:46 AM Default Gateway . . . . . . . . . : 192.168.43.1 DHCP Server . . . . . . . . . . . : 192.168.43.1 DHCPv6 IAID . . . . . . . . . . . : 83146722 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-19-F1-98-B4-20-89-84-84-61-BB DNS Servers . . . . . . . . . . . : 192.168.43.1 NetBIOS over Tcpip. . . . . . . . : Enabled Ethernet adapter Ethernet: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Broadcom NetLink (TM) Gigabit Ethernet Physical Address. . . . . . . . . : 20-89-84-84-61-BB DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Log Name: System Source: Microsoft-Windows-UserPnp Date: 10/26/2013 7:52:23 PM Event ID: 20003 Task Category: (7005) Level: Information Keywords: User: SYSTEM Computer: NastyMcnastyJr Description: Driver Management has concluded the process to add Service vwifibus for Device Instance ID PCI\VEN_14E4&DEV_4727&SUBSYS_E042105B&REV_01\4&3265ADAB&0&00E1 with the following status: 0. Event Xml: 20003 0 4 7005 0 0x8000000000000000 5118 System NastyMcnastyJr vwifibus \SystemRoot\system32\DRIVERS\vwifibus.sys PCI\VEN_14E4&DEV_4727&SUBSYS_E042105B&REV_01\4&3265ADAB&0&00E1 false true 0 Log Name: System Source: Microsoft-Windows-UserPnp Date: 10/19/2013 3:29:12 PM Event ID: 20001 Task Category: (7005) Level: Information Keywords: User: SYSTEM Computer: NastyMcnastyJr Description: Driver Management concluded the process to install driver netbc64.inf_amd64_0df63b5297d0f820\netbc64.inf for Device Instance ID PCI\VEN_14E4&DEV_4727&SUBSYS_E042105B&REV_01\4&3265ADAB&0&00E1 with the following status: 0x0. Event Xml: 20001 0 4 7005 0 0x8000000000000000 2015 System NastyMcnastyJr netbc64.inf_amd64_0df63b5297d0f820\netbc64.inf 6.30.223.102 Microsoft PCI\VEN_14E4&DEV_4727&SUBSYS_E042105B&REV_01\4&3265ADAB&0&00E1 {4D36E972-E325-11CE-BFC1-08002BE10318} false false false 0x0 Broadcom 802.11n Network Adapter Log Name: System Source: Microsoft-Windows-DNS-Client Date: 11/2/2013 12:24:59 AM Event ID: 1014 Task Category: (1014) Level: Warning Keywords: (268435456) User: NETWORK SERVICE Computer: NastyMcnastyJr Description: Name resolution for the name www.google.com timed out after none of the configured DNS servers responded. Event Xml: 1014 0 3 1014 0 0x4000000010000000 34771 System NastyMcnastyJr www.google.com 128 02000000C0A82B01000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000

    Read the article

  • OpenVPN - Windows 8 to Windows 2008 Server, not connecting

    - by niico
    I have followed this tutorial about setting up an OpenVPN Server on Windows Server - and a client on Windows (in this case Windows 8). The server appears to be running fine - but it is not connecting with this error: Mon Jul 22 19:09:04 2013 Warning: cannot open --log file: C:\Program Files\OpenVPN\log\my-laptop.log: Access is denied. (errno=5) Mon Jul 22 19:09:04 2013 OpenVPN 2.3.2 x86_64-w64-mingw32 [SSL (OpenSSL)] [LZO] [PKCS11] [eurephia] [IPv6] built on Jun 3 2013 Mon Jul 22 19:09:04 2013 MANAGEMENT: TCP Socket listening on [AF_INET]127.0.0.1:25340 Mon Jul 22 19:09:04 2013 Need hold release from management interface, waiting... Mon Jul 22 19:09:05 2013 MANAGEMENT: Client connected from [AF_INET]127.0.0.1:25340 Mon Jul 22 19:09:05 2013 MANAGEMENT: CMD 'state on' Mon Jul 22 19:09:05 2013 MANAGEMENT: CMD 'log all on' Mon Jul 22 19:09:05 2013 MANAGEMENT: CMD 'hold off' Mon Jul 22 19:09:05 2013 MANAGEMENT: CMD 'hold release' Mon Jul 22 19:09:05 2013 Socket Buffers: R=[65536->65536] S=[65536->65536] Mon Jul 22 19:09:05 2013 UDPv4 link local: [undef] Mon Jul 22 19:09:05 2013 UDPv4 link remote: [AF_INET]66.666.66.666:9999 Mon Jul 22 19:09:05 2013 MANAGEMENT: >STATE:1374494945,WAIT,,, Mon Jul 22 19:10:05 2013 TLS Error: TLS key negotiation failed to occur within 60 seconds (check your network connectivity) Mon Jul 22 19:10:05 2013 TLS Error: TLS handshake failed Mon Jul 22 19:10:05 2013 SIGUSR1[soft,tls-error] received, process restarting Mon Jul 22 19:10:05 2013 MANAGEMENT: >STATE:1374495005,RECONNECTING,tls-error,, Mon Jul 22 19:10:05 2013 Restart pause, 2 second(s) Note I have changed the IP and port no (it uses a non-standard port for security reasons). That port is open on the hardware firewall. The server logs are showing a connection attempt from my client: TLS: Initial packet from [AF_INET]118.68.xx.xx:65011, sid=081af4ed xxxxxxxx Mon Jul 22 14:19:15 2013 118.68.xx.xx:65011 TLS Error: TLS key negotiation failed to occur within 60 seconds (check your network connectivity) How can I problem solve this & find the problem? Thx Update - Client config file: ############################################## # Sample client-side OpenVPN 2.0 config file # # for connecting to multi-client server. # # # # This configuration can be used by multiple # # clients, however each client should have # # its own cert and key files. # # # # On Windows, you might want to rename this # # file so it has a .ovpn extension # ############################################## # Specify that we are a client and that we # will be pulling certain config file directives # from the server. client # Use the same setting as you are using on # the server. # On most systems, the VPN will not function # unless you partially or fully disable # the firewall for the TUN/TAP interface. ;dev tap dev tun # Windows needs the TAP-Win32 adapter name # from the Network Connections panel # if you have more than one. On XP SP2, # you may need to disable the firewall # for the TAP adapter. ;dev-node MyTap # Are we connecting to a TCP or # UDP server? Use the same setting as # on the server. ;proto tcp proto udp # The hostname/IP and port of the server. # You can have multiple remote entries # to load balance between the servers. remote 00.00.00.00 1194 ;remote 00.00.00.00 9999 ;remote my-server-2 1194 # Choose a random host from the remote # list for load-balancing. Otherwise # try hosts in the order specified. ;remote-random # Keep trying indefinitely to resolve the # host name of the OpenVPN server. Very useful # on machines which are not permanently connected # to the internet such as laptops. resolv-retry infinite # Most clients don't need to bind to # a specific local port number. nobind # Downgrade privileges after initialization (non-Windows only) ;user nobody ;group nobody # Try to preserve some state across restarts. persist-key persist-tun # If you are connecting through an # HTTP proxy to reach the actual OpenVPN # server, put the proxy server/IP and # port number here. See the man page # if your proxy server requires # authentication. ;http-proxy-retry # retry on connection failures ;http-proxy [proxy server] [proxy port #] # Wireless networks often produce a lot # of duplicate packets. Set this flag # to silence duplicate packet warnings. ;mute-replay-warnings # SSL/TLS parms. # See the server config file for more # description. It's best to use # a separate .crt/.key file pair # for each client. A single ca # file can be used for all clients. ca "C:\\Program Files\\OpenVPN\\config\\ca.crt" cert "C:\\Program Files\\OpenVPN\\config\\my-laptop.crt" key "C:\\Program Files\\OpenVPN\\config\\my-laptop.key" # Verify server certificate by checking # that the certicate has the nsCertType # field set to "server". This is an # important precaution to protect against # a potential attack discussed here: # http://openvpn.net/howto.html#mitm # # To use this feature, you will need to generate # your server certificates with the nsCertType # field set to "server". The build-key-server # script in the easy-rsa folder will do this. ns-cert-type server # If a tls-auth key is used on the server # then every client must also have the key. ;tls-auth ta.key 1 # Select a cryptographic cipher. # If the cipher option is used on the server # then you must also specify it here. ;cipher x # Enable compression on the VPN link. # Don't enable this unless it is also # enabled in the server config file. comp-lzo # Set log file verbosity. verb 3 # Silence repeating messages ;mute 20 Server config file: ################################################# # Sample OpenVPN 2.0 config file for # # multi-client server. # # # # This file is for the server side # # of a many-clients <-> one-server # # OpenVPN configuration. # # # # OpenVPN also supports # # single-machine <-> single-machine # # configurations (See the Examples page # # on the web site for more info). # # # # This config should work on Windows # # or Linux/BSD systems. Remember on # # Windows to quote pathnames and use # # double backslashes, e.g.: # # "C:\\Program Files\\OpenVPN\\config\\foo.key" # # # # Comments are preceded with '#' or ';' # ################################################# # Which local IP address should OpenVPN # listen on? (optional) ;local 00.00.00.00 # Which TCP/UDP port should OpenVPN listen on? # If you want to run multiple OpenVPN instances # on the same machine, use a different port # number for each one. You will need to # open up this port on your firewall. std 1194 port 1194 # TCP or UDP server? ;proto tcp proto udp # "dev tun" will create a routed IP tunnel, # "dev tap" will create an ethernet tunnel. # Use "dev tap0" if you are ethernet bridging # and have precreated a tap0 virtual interface # and bridged it with your ethernet interface. # If you want to control access policies # over the VPN, you must create firewall # rules for the the TUN/TAP interface. # On non-Windows systems, you can give # an explicit unit number, such as tun0. # On Windows, use "dev-node" for this. # On most systems, the VPN will not function # unless you partially or fully disable # the firewall for the TUN/TAP interface. ;dev tap dev tun # Windows needs the TAP-Win32 adapter name # from the Network Connections panel if you # have more than one. On XP SP2 or higher, # you may need to selectively disable the # Windows firewall for the TAP adapter. # Non-Windows systems usually don't need this. ;dev-node MyTap # SSL/TLS root certificate (ca), certificate # (cert), and private key (key). Each client # and the server must have their own cert and # key file. The server and all clients will # use the same ca file. # # See the "easy-rsa" directory for a series # of scripts for generating RSA certificates # and private keys. Remember to use # a unique Common Name for the server # and each of the client certificates. # # Any X509 key management system can be used. # OpenVPN can also use a PKCS #12 formatted key file # (see "pkcs12" directive in man page). ca "C:\\Program Files\\OpenVPN\\config\\ca.crt" cert "C:\\Program Files\\OpenVPN\\config\\server.crt" key "C:\\Program Files\\OpenVPN\\config\\server.key" # Diffie hellman parameters. # Generate your own with: # openssl dhparam -out dh1024.pem 1024 # Substitute 2048 for 1024 if you are using # 2048 bit keys. dh "C:\\Program Files\\OpenVPN\\config\\dh2048.pem" # Configure server mode and supply a VPN subnet # for OpenVPN to draw client addresses from. # The server will take 10.8.0.1 for itself, # the rest will be made available to clients. # Each client will be able to reach the server # on 10.8.0.1. Comment this line out if you are # ethernet bridging. See the man page for more info. server 10.8.0.0 255.255.255.0 # Maintain a record of client <-> virtual IP address # associations in this file. If OpenVPN goes down or # is restarted, reconnecting clients can be assigned # the same virtual IP address from the pool that was # previously assigned. ifconfig-pool-persist ipp.txt # Configure server mode for ethernet bridging. # You must first use your OS's bridging capability # to bridge the TAP interface with the ethernet # NIC interface. Then you must manually set the # IP/netmask on the bridge interface, here we # assume 10.8.0.4/255.255.255.0. Finally we # must set aside an IP range in this subnet # (start=10.8.0.50 end=10.8.0.100) to allocate # to connecting clients. Leave this line commented # out unless you are ethernet bridging. ;server-bridge 10.8.0.4 255.255.255.0 10.8.0.50 10.8.0.100 # Configure server mode for ethernet bridging # using a DHCP-proxy, where clients talk # to the OpenVPN server-side DHCP server # to receive their IP address allocation # and DNS server addresses. You must first use # your OS's bridging capability to bridge the TAP # interface with the ethernet NIC interface. # Note: this mode only works on clients (such as # Windows), where the client-side TAP adapter is # bound to a DHCP client. ;server-bridge # Push routes to the client to allow it # to reach other private subnets behind # the server. Remember that these # private subnets will also need # to know to route the OpenVPN client # address pool (10.8.0.0/255.255.255.0) # back to the OpenVPN server. ;push "route 192.168.10.0 255.255.255.0" ;push "route 192.168.20.0 255.255.255.0" # To assign specific IP addresses to specific # clients or if a connecting client has a private # subnet behind it that should also have VPN access, # use the subdirectory "ccd" for client-specific # configuration files (see man page for more info). # EXAMPLE: Suppose the client # having the certificate common name "Thelonious" # also has a small subnet behind his connecting # machine, such as 192.168.40.128/255.255.255.248. # First, uncomment out these lines: ;client-config-dir ccd ;route 192.168.40.128 255.255.255.248 # Then create a file ccd/Thelonious with this line: # iroute 192.168.40.128 255.255.255.248 # This will allow Thelonious' private subnet to # access the VPN. This example will only work # if you are routing, not bridging, i.e. you are # using "dev tun" and "server" directives. # EXAMPLE: Suppose you want to give # Thelonious a fixed VPN IP address of 10.9.0.1. # First uncomment out these lines: ;client-config-dir ccd ;route 10.9.0.0 255.255.255.252 # Then add this line to ccd/Thelonious: # ifconfig-push 10.9.0.1 10.9.0.2 # Suppose that you want to enable different # firewall access policies for different groups # of clients. There are two methods: # (1) Run multiple OpenVPN daemons, one for each # group, and firewall the TUN/TAP interface # for each group/daemon appropriately. # (2) (Advanced) Create a script to dynamically # modify the firewall in response to access # from different clients. See man # page for more info on learn-address script. ;learn-address ./script # If enabled, this directive will configure # all clients to redirect their default # network gateway through the VPN, causing # all IP traffic such as web browsing and # and DNS lookups to go through the VPN # (The OpenVPN server machine may need to NAT # or bridge the TUN/TAP interface to the internet # in order for this to work properly). ;push "redirect-gateway def1 bypass-dhcp" # Certain Windows-specific network settings # can be pushed to clients, such as DNS # or WINS server addresses. CAVEAT: # http://openvpn.net/faq.html#dhcpcaveats # The addresses below refer to the public # DNS servers provided by opendns.com. ;push "dhcp-option DNS 208.67.222.222" ;push "dhcp-option DNS 208.67.220.220" # Uncomment this directive to allow differenta # clients to be able to "see" each other. # By default, clients will only see the server. # To force clients to only see the server, you # will also need to appropriately firewall the # server's TUN/TAP interface. ;client-to-client # Uncomment this directive if multiple clients # might connect with the same certificate/key # files or common names. This is recommended # only for testing purposes. For production use, # each client should have its own certificate/key # pair. # # IF YOU HAVE NOT GENERATED INDIVIDUAL # CERTIFICATE/KEY PAIRS FOR EACH CLIENT, # EACH HAVING ITS OWN UNIQUE "COMMON NAME", # UNCOMMENT THIS LINE OUT. ;duplicate-cn # The keepalive directive causes ping-like # messages to be sent back and forth over # the link so that each side knows when # the other side has gone down. # Ping every 10 seconds, assume that remote # peer is down if no ping received during # a 120 second time period. keepalive 10 120 # For extra security beyond that provided # by SSL/TLS, create an "HMAC firewall" # to help block DoS attacks and UDP port flooding. # # Generate with: # openvpn --genkey --secret ta.key # # The server and each client must have # a copy of this key. # The second parameter should be '0' # on the server and '1' on the clients. ;tls-auth ta.key 0 # This file is secret # Select a cryptographic cipher. # This config item must be copied to # the client config file as well. ;cipher BF-CBC # Blowfish (default) ;cipher AES-128-CBC # AES ;cipher DES-EDE3-CBC # Triple-DES # Enable compression on the VPN link. # If you enable it here, you must also # enable it in the client config file. comp-lzo # The maximum number of concurrently connected # clients we want to allow. ;max-clients 100 # It's a good idea to reduce the OpenVPN # daemon's privileges after initialization. # # You can uncomment this out on # non-Windows systems. ;user nobody ;group nobody # The persist options will try to avoid # accessing certain resources on restart # that may no longer be accessible because # of the privilege downgrade. persist-key persist-tun # Output a short status file showing # current connections, truncated # and rewritten every minute. status openvpn-status.log # By default, log messages will go to the syslog (or # on Windows, if running as a service, they will go to # the "\Program Files\OpenVPN\log" directory). # Use log or log-append to override this default. # "log" will truncate the log file on OpenVPN startup, # while "log-append" will append to it. Use one # or the other (but not both). ;log openvpn.log ;log-append openvpn.log # Set the appropriate level of log # file verbosity. # # 0 is silent, except for fatal errors # 4 is reasonable for general usage # 5 and 6 can help to debug connection problems # 9 is extremely verbose verb 3 # Silence repeating messages. At most 20 # sequential messages of the same message # category will be output to the log. ;mute 20 I have changed IP's for security

    Read the article

  • DD-WRT No Internet connection over LAN

    - by algorithms
    I flashed the DD-WRT firmware on my TP-Link WR1043ND router and although after cloning the PC's MAC-Address it gets the correct IP from my ISP, the internet connection over LAN just won't work. The strange thing is it does work flawlessly over W-LAN, which tells me the problem should lie somehow in the default LAN settings or the PC. Any idea what the problem might be? UPDATE: It seems the problem is the desktop PC, since the laptop can connect to the interet via ethernet without any problems. ipconfig /all seems totally normal (dhcp, dns, gateway all set to 192.168.1.1) I already tried the following things without success: disabling firewall rebooting router/modem/pc router hard-reset resetting tcp/ip and winsock manual setting of DNS/IP/Gateway Here is the ipconfig /all: Windows-IP-Konfiguration Hostname . . . . . . . . . . . . : Nitro-PC Primäres DNS-Suffix . . . . . . . : Knotentyp . . . . . . . . . . . . : Hybrid IP-Routing aktiviert . . . . . . : Nein WINS-Proxy aktiviert . . . . . . : Nein Ethernet-Adapter LAN-Verbindung 2: Medienstatus. . . . . . . . . . . : Medium getrennt Verbindungsspezifisches DNS-Suffix: Beschreibung. . . . . . . . . . . : TAP-Win32 Adapter V9 Physikalische Adresse . . . . . . : 00-FF-56-CA-66-8D DHCP aktiviert. . . . . . . . . . : Ja Autokonfiguration aktiviert . . . : Ja Ethernet-Adapter LAN-Verbindung: Verbindungsspezifisches DNS-Suffix: Beschreibung. . . . . . . . . . . : Realtek PCIe GBE Family Controller Physikalische Adresse . . . . . . : 48-5B-39-5B-DE-17 DHCP aktiviert. . . . . . . . . . : Ja Autokonfiguration aktiviert . . . : Ja Verbindungslokale IPv6-Adresse . : fe80::6934:b121:9eab:c6ce%10(Bevorzugt) IPv4-Adresse . . . . . . . . . . : 192.168.1.18(Bevorzugt) Subnetzmaske . . . . . . . . . . : 255.255.255.0 Lease erhalten. . . . . . . . . . : Donnerstag, 30. August 2012 10:52:30 Lease läuft ab. . . . . . . . . . : Freitag, 31. August 2012 10:52:30 Standardgateway . . . . . . . . . : 192.168.1.1 DHCP-Server . . . . . . . . . . . : 192.168.1.1 DHCPv6-IAID . . . . . . . . . . . : 239622969 DHCPv6-Client-DUID. . . . . . . . : 00-01-00-01-17-43-0D-B2-48-5B-39-5B-DE-17 DNS-Server . . . . . . . . . . . : 192.168.1.1 NetBIOS über TCP/IP . . . . . . . : Aktiviert Tunneladapter isatap.{56CA668D-9112-4399-9D9A-F1D42F0E52DE}: Medienstatus. . . . . . . . . . . : Medium getrennt Verbindungsspezifisches DNS-Suffix: Beschreibung. . . . . . . . . . . : Microsoft-ISATAP-Adapter Physikalische Adresse . . . . . . : 00-00-00-00-00-00-00-E0 DHCP aktiviert. . . . . . . . . . : Nein Autokonfiguration aktiviert . . . : Ja Tunneladapter Teredo Tunneling Pseudo-Interface: Verbindungsspezifisches DNS-Suffix: Beschreibung. . . . . . . . . . . : Teredo Tunneling Pseudo-Interface Physikalische Adresse . . . . . . : 00-00-00-00-00-00-00-E0 DHCP aktiviert. . . . . . . . . . : Nein Autokonfiguration aktiviert . . . : Ja IPv6-Adresse. . . . . . . . . . . : 2001:0:5ef5:79fd:1432:3dcd:3f57:feed(Bevorzugt) Verbindungslokale IPv6-Adresse . : fe80::1432:3dcd:3f57:feed%12(Bevorzugt) Standardgateway . . . . . . . . . : :: NetBIOS über TCP/IP . . . . . . . : Deaktiviert Tunneladapter isatap.{AD21069D-D2AF-423E-BF59-0B1CD0D235E8}: Medienstatus. . . . . . . . . . . : Medium getrennt Verbindungsspezifisches DNS-Suffix: Beschreibung. . . . . . . . . . . : Microsoft-ISATAP-Adapter #2 Physikalische Adresse . . . . . . : 00-00-00-00-00-00-00-E0 DHCP aktiviert. . . . . . . . . . : Nein Autokonfiguration aktiviert . . . : Ja Tunneladapter 6TO4 Adapter: Medienstatus. . . . . . . . . . . : Medium getrennt Verbindungsspezifisches DNS-Suffix: Beschreibung. . . . . . . . . . . : Microsoft-6zu4-Adapter Physikalische Adresse . . . . . . : 00-00-00-00-00-00-00-E0 DHCP aktiviert. . . . . . . . . . : Nein Autokonfiguration aktiviert . . . : Ja route PRINT IPv4-Routentabelle =========================================================================== Aktive Routen: Netzwerkziel Netzwerkmaske Gateway Schnittstelle Metrik 0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.18 10 127.0.0.0 255.0.0.0 Auf Verbindung 127.0.0.1 306 127.0.0.1 255.255.255.255 Auf Verbindung 127.0.0.1 306 127.255.255.255 255.255.255.255 Auf Verbindung 127.0.0.1 306 192.168.1.0 255.255.255.0 Auf Verbindung 192.168.1.18 266 192.168.1.18 255.255.255.255 Auf Verbindung 192.168.1.18 266 192.168.1.255 255.255.255.255 Auf Verbindung 192.168.1.18 266 224.0.0.0 240.0.0.0 Auf Verbindung 127.0.0.1 306 224.0.0.0 240.0.0.0 Auf Verbindung 192.168.1.18 266 255.255.255.255 255.255.255.255 Auf Verbindung 127.0.0.1 306 255.255.255.255 255.255.255.255 Auf Verbindung 192.168.1.18 266 =========================================================================== Stndige Routen: Keine

    Read the article

  • Wired connection periodically disconnects requires ipconfig /release and /renew to reconnect

    - by Sesame
    I just got back into University and after a day of using the internet I suddenly was unable to visit other webpages even though I was still able to chat. I restarted the computer and the internet could no longer visit webpages at all. I got a DNS error from the browser (chrome) and the troubleshooter. The connection comes up as "Network 3" even though It was "Network 2" when it worked. I compared ipconfig /all logs and they seemed identical when it was and was not working. I've found two ways to get internet connection (they no longer work): run ipconfig /release and ipconfig /renew several times set a random address and have the troubleshooter fix the new found dhcp problem (before it says dns cannot fix). I checked and it said DHCP was enabled. But either step one or two usually needs to be repeated several times before the network will change back to "network 2" from the defunct "network 3" and after an hour or so I have problems again. I've tried: Uninstalling windows defender and turning off firewall (windows firewall). Updating Qualcomm Ethernet driver - it is up to date. System Restore (problem resurfaces quickly...it's possible this has something to do with windows update?) Flushing dns and setting dns myself (google one and others). Booting in safe mode with networking...didn't fix anything Reinstalling Ethernet Driver Using other ethernet cable, other wall port. I'm out of ideas. Ipconfig /all: Windows IP Configuration Host Name . . . . . . . . . . . . : NGoller Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : Home Ethernet adapter UConnect: Connection-specific DNS Suffix . : Home Description . . . . . . . . . . . : Qualcomm Atheros AR8151 PCI-E Gigabit Ethernet Controller Physical Address. . . . . . . . . : 90-2B-34-50-33-F4 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IPv6 Address. . . . . . . . . . . : fd00::2086:628:f0a1:73c3(Preferred) Temporary IPv6 Address. . . . . . : fd00::c86b:370:b1d9:bd73(Preferred) Link-local IPv6 Address . . . . . : fe80::2086:628:f0a1:73c3%11(Preferred) IPv4 Address. . . . . . . . . . . : 192.168.0.33(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : Wednesday, August 28, 2013 11:58:37 PM Lease Expires . . . . . . . . . . : Thursday, August 29, 2013 11:58:37 PM Default Gateway . . . . . . . . . : 192.168.0.1 DHCP Server . . . . . . . . . . . : 192.168.0.1 DNS Servers . . . . . . . . . . . : 192.168.0.1 NetBIOS over Tcpip. . . . . . . . : Enabled Tunnel adapter isatap.Home: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Home Description . . . . . . . . . . . : Microsoft ISATAP Adapter Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Tunnel adapter Teredo Tunneling Pseudo-Interface: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes I'm getting these errors commonly: The IP address lease 155.97.227.199 for the Network Card with network address 0x902B345033F4 has been denied by the DHCP server 10.0.1.1 (The DHCP Server sent a DHCPNACK message). Event filter with query "SELECT * FROM __InstanceModificationEvent WITHIN 60 WHERE TargetInstance ISA "Win32_Processor" AND TargetInstance.LoadPercentage > 99" could not be reactivated in namespace "//./root/CIMV2" because of error 0x80041003. Events cannot be delivered through this filter until the problem is corrected. By the way, Operating System: Windows 7 - 64 Bit. Have downloaded latest windows updates. Update: And my two fixes don't work any more :( . This is now what happens when I try to Ipconfig /renew: C:\Users\Nikko\Desktop>ipconfig /renew Windows IP Configuration An error occurred while renewing interface Local Area Connection : The name spec ified in the network control block (NCB) is in use on a remote adapter. The NCB is the data. An error occurred while releasing interface Loopback Pseudo-Interface 1 : The sy stem cannot find the file specified. Update 2: So my internet is randomly working again today. The IP address I had before was a local one while the university address should start with 155... I didn't do anything to the settings...it's bizarre that it all of a sudden works. Thanks!

    Read the article

  • Weird WLAN connection

    - by tuelsch
    I assembled my first computer on my own. As I realised it had no WLAN (AsRock Z77 Extreme 4m) I bought a WLAN stick (ZyXel NWD 2105), plugged it in, started the setup from the CD and it worked, until I restarted the PC. That's when the problems started. The stick is able to connect to the router (P-660HN-F1Z) and the connection is stable, but not the internet access. In estimately 1 minute intervals there might be a short connection timeframe and dropbox or windows update are able to download some data, but as soon as I try to open a website the internet access is away. Note that the connection to the router does not shut down and remains stable at around 80-90%. The problem is definetly located on my pc, because with my laptop and phone the connection is stable and fast. Because I was so pissed off, I bought a EW-7612PIn V2 (PCI-E WLAN adapter), same problem. Now the weird thing is, if I don't use the PC for about 2 days, start it up, there is internet access (happened with both the stick and the PCI-E card). A bit slow, but it does not get away just like that, until I shut it down. Then, no matter how many times I restart, it won't come back. I googled a lot but now I'm at the end with my latin. Has anyone had a similar problem and resolved it? Technical details: Motherboard: AsRock Z77 Extreme 4M OS: Windows 7 professional 64bit Stick: Zyxel wireless N adapter NWD2105 PCI-E card: Edimax EW-7612PIn V2 Router: ZyXel P-660HN-F1Z Windows-IP-Konfiguration Hostname . . . . . . . . . . . . : xyz Primäres DNS-Suffix . . . . . . . : Knotentyp . . . . . . . . . . . . : Hybrid IP-Routing aktiviert . . . . . . : Nein WINS-Proxy aktiviert . . . . . . : Nein Drahtlos-LAN-Adapter Drahtlosnetzwerkverbindung 5: Medienstatus. . . . . . . . . . . : Medium getrennt Verbindungsspezifisches DNS-Suffix: Beschreibung. . . . . . . . . . . : Microsoft Virtual WiFi Miniport Adapter # 3 Physikalische Adresse . . . . . . : 80-1F-02-61-C0-A6 DHCP aktiviert. . . . . . . . . . : Ja Autokonfiguration aktiviert . . . : Ja Drahtlos-LAN-Adapter Drahtlosnetzwerkverbindung 4: Verbindungsspezifisches DNS-Suffix: Beschreibung. . . . . . . . . . . : Edimax 802.11n Wireless Adapter Physikalische Adresse . . . . . . : 80-1F-02-61-C0-A6 DHCP aktiviert. . . . . . . . . . : Ja Autokonfiguration aktiviert . . . : Ja Verbindungslokale IPv6-Adresse . : fe80::38d2:f489:726d:1fb5%17(Bevorzugt) IPv4-Adresse . . . . . . . . . . : 192.168.1.41(Bevorzugt) Subnetzmaske . . . . . . . . . . : 255.255.255.0 Lease erhalten. . . . . . . . . . : Donnerstag, 15. November 2012 10:51:05 Lease läuft ab. . . . . . . . . . : Sonntag, 18. November 2012 10:51:18 Standardgateway . . . . . . . . . : 192.168.1.1 DHCP-Server . . . . . . . . . . . : 192.168.1.1 DHCPv6-IAID . . . . . . . . . . . : 578821890 DHCPv6-Client-DUID. . . . . . . . : 00-01-00-01-17-FF-D5-FE-BC-5F-F4-48-FC-4B DNS-Server . . . . . . . . . . . : 91.233.182.2 194.230.1.39 NetBIOS über TCP/IP . . . . . . . : Aktiviert Tunneladapter isatap.{263BEB98-344B-435C-888F-1B15B97C3AC1}: Medienstatus. . . . . . . . . . . : Medium getrennt Verbindungsspezifisches DNS-Suffix: Beschreibung. . . . . . . . . . . : Microsoft-ISATAP-Adapter Physikalische Adresse . . . . . . : 00-00-00-00-00-00-00-E0 DHCP aktiviert. . . . . . . . . . : Nein Autokonfiguration aktiviert . . . : Ja Tunneladapter Teredo Tunneling Pseudo-Interface: Verbindungsspezifisches DNS-Suffix: Beschreibung. . . . . . . . . . . : Teredo Tunneling Pseudo-Interface Physikalische Adresse . . . . . . : 00-00-00-00-00-00-00-E0 DHCP aktiviert. . . . . . . . . . : Nein Autokonfiguration aktiviert . . . : Ja IPv6-Adresse. . . . . . . . . . . : 2001:0:9d38:6ab8:209c:2944:3f57:fed6(Bevo rzugt) Verbindungslokale IPv6-Adresse . : fe80::209c:2944:3f57:fed6%11(Bevorzugt) Standardgateway . . . . . . . . . : :: NetBIOS über TCP/IP . . . . . . . : Deaktiviert C:\Users\xyz>ping 192.168.1.1 Ping wird ausgeführt für 192.168.1.1 mit 32 Bytes Daten: Antwort von 192.168.1.1: Bytes=32 Zeit=2ms TTL=254 Antwort von 192.168.1.1: Bytes=32 Zeit=2ms TTL=254 Antwort von 192.168.1.1: Bytes=32 Zeit=2ms TTL=254 Antwort von 192.168.1.1: Bytes=32 Zeit=2ms TTL=254 Ping-Statistik für 192.168.1.1: Pakete: Gesendet = 4, Empfangen = 4, Verloren = 0 (0% Verlust), Ca. Zeitangaben in Millisek.: Minimum = 2ms, Maximum = 2ms, Mittelwert = 2ms

    Read the article

  • Marking Current Location on Map, Android

    - by deewangan
    Hi every one, i followed some tutorials to create an application that shows the current position of the user on the map with a marking. but for some reasons i can't get to work the marking part? the other parts works well, but whenever i add the marking code the application crashes. i hope someone could help me.here is the code: public class LocationActivity extends MapActivity { /** Called when the activity is first created. */ private MapView mapView; private LocationManager lm; private LocationListener ll; private MapController mc; GeoPoint p = null; Drawable defaultMarker = null; @Override public void onCreate(Bundle savedInstanceState) { super.onCreate(savedInstanceState); setContentView(R.layout.main); mapView = (MapView)findViewById(R.id.mapView); //show zoom in/out buttons mapView.setBuiltInZoomControls(true); //Standard view of the map(map/sat) mapView.setSatellite(false); //get controller of the map for zooming in/out mc = mapView.getController(); // Zoom Level mc.setZoom(18); MyLocationOverlay myLocationOverlay = new MyLocationOverlay(); List<Overlay> list = mapView.getOverlays(); list.add(myLocationOverlay); lm = (LocationManager)getSystemService(Context.LOCATION_SERVICE); ll = new MyLocationListener(); lm.requestLocationUpdates( LocationManager.GPS_PROVIDER, 0, 0, ll); //Get the current location in start-up GeoPoint initGeoPoint = new GeoPoint( (int)(lm.getLastKnownLocation( LocationManager.GPS_PROVIDER) .getLatitude()*1000000), (int)(lm.getLastKnownLocation( LocationManager.GPS_PROVIDER) .getLongitude()*1000000)); mc.animateTo(initGeoPoint); } protected class MyLocationOverlay extends com.google.android.maps.Overlay { @Override public boolean draw(Canvas canvas, MapView mapView, boolean shadow, long when) { Paint paint = new Paint(); super.draw(canvas, mapView, shadow); // Converts lat/lng-Point to OUR coordinates on the screen. Point myScreenCoords = new Point(); mapView.getProjection().toPixels(p, myScreenCoords); paint.setStrokeWidth(1); paint.setARGB(255, 255, 255, 255); paint.setStyle(Paint.Style.STROKE); Bitmap bmp = BitmapFactory.decodeResource(getResources(), R.drawable.push); canvas.drawBitmap(bmp, myScreenCoords.x, myScreenCoords.y, paint); canvas.drawText("I am here...", myScreenCoords.x, myScreenCoords.y, paint); return true; } } private class MyLocationListener implements LocationListener{ public void onLocationChanged(Location argLocation) { // TODO Auto-generated method stub GeoPoint myGeoPoint = new GeoPoint( (int)(argLocation.getLatitude()*1000000), (int)(argLocation.getLongitude()*1000000)); /* * it will show a message on * location change Toast.makeText(getBaseContext(), "New location latitude [" +argLocation.getLatitude() + "] longitude [" + argLocation.getLongitude()+"]", Toast.LENGTH_SHORT).show(); */ mc.animateTo(myGeoPoint); } public void onProviderDisabled(String provider) { // TODO Auto-generated method stub } public void onProviderEnabled(String provider) { // TODO Auto-generated method stub } public void onStatusChanged(String provider, int status, Bundle extras) { // TODO Auto-generated method stub } } protected boolean isRouteDisplayed() { return false; } } here is the logcat: 01-19 05:31:43.011: DEBUG/AndroidRuntime(759): >>>>>>>>>>>>>> AndroidRuntime START <<<<<<<<<<<<<< 01-19 05:31:43.011: DEBUG/AndroidRuntime(759): CheckJNI is ON 01-19 05:31:43.411: DEBUG/AndroidRuntime(759): --- registering native functions --- 01-19 05:31:43.431: INFO/jdwp(759): received file descriptor 19 from ADB 01-19 05:31:43.431: INFO/jdwp(759): Ignoring second debugger -- accepting and dropping 01-19 05:31:44.531: INFO/ActivityManager(583): Starting activity: Intent { flg=0x10000000 cmp=pro.googlemapp/.LocationActivity } 01-19 05:31:44.641: DEBUG/AndroidRuntime(759): Shutting down VM 01-19 05:31:44.641: DEBUG/dalvikvm(759): DestroyJavaVM waiting for non-daemon threads to exit 01-19 05:31:44.641: DEBUG/dalvikvm(759): DestroyJavaVM shutting VM down 01-19 05:31:44.641: DEBUG/dalvikvm(759): HeapWorker thread shutting down 01-19 05:31:44.651: DEBUG/dalvikvm(759): HeapWorker thread has shut down 01-19 05:31:44.651: DEBUG/jdwp(759): JDWP shutting down net... 01-19 05:31:44.651: DEBUG/jdwp(759): +++ peer disconnected 01-19 05:31:44.651: INFO/dalvikvm(759): Debugger has detached; object registry had 1 entries 01-19 05:31:44.661: DEBUG/dalvikvm(759): VM cleaning up 01-19 05:31:44.681: INFO/ActivityManager(583): Start proc pro.googlemapp for activity pro.googlemapp/.LocationActivity: pid=770 uid=10025 gids={3003} 01-19 05:31:44.761: DEBUG/dalvikvm(759): LinearAlloc 0x0 used 676436 of 4194304 (16%) 01-19 05:31:44.801: INFO/jdwp(770): received file descriptor 20 from ADB 01-19 05:31:44.822: INFO/dalvikvm(770): ignoring registerObject request in thread=3 01-19 05:31:44.851: INFO/jdwp(770): Ignoring second debugger -- accepting and dropping 01-19 05:31:44.851: ERROR/jdwp(770): Failed writing handshake bytes: Broken pipe (-1 of 14) 01-19 05:31:44.851: INFO/dalvikvm(770): Debugger has detached; object registry had 0 entries 01-19 05:31:45.320: ERROR/ActivityThread(770): Failed to find provider info for com.google.settings 01-19 05:31:45.320: ERROR/ActivityThread(770): Failed to find provider info for com.google.settings 01-19 05:31:45.340: ERROR/ActivityThread(770): Failed to find provider info for com.google.settings 01-19 05:31:45.781: DEBUG/LocationManager(770): Constructor: service = android.location.ILocationManager$Stub$Proxy@4379d9f0 01-19 05:31:45.791: WARN/GpsLocationProvider(583): Duplicate add listener for uid 10025 01-19 05:31:45.791: DEBUG/GpsLocationProvider(583): setMinTime 0 01-19 05:31:45.791: DEBUG/GpsLocationProvider(583): startNavigating 01-19 05:31:45.831: INFO/jdwp(770): received file descriptor 27 from ADB 01-19 05:31:46.001: INFO/MapActivity(770): Handling network change notification:CONNECTED 01-19 05:31:46.001: ERROR/MapActivity(770): Couldn't get connection factory client 01-19 05:31:46.451: DEBUG/dalvikvm(770): GC freed 4539 objects / 298952 bytes in 118ms 01-19 05:31:46.470: DEBUG/AndroidRuntime(770): Shutting down VM 01-19 05:31:46.470: WARN/dalvikvm(770): threadid=3: thread exiting with uncaught exception (group=0x4001aa28) 01-19 05:31:46.481: ERROR/AndroidRuntime(770): Uncaught handler: thread main exiting due to uncaught exception 01-19 05:31:46.541: ERROR/AndroidRuntime(770): java.lang.NullPointerException 01-19 05:31:46.541: ERROR/AndroidRuntime(770): at com.google.android.maps.PixelConverter.toPixels(PixelConverter.java:58) 01-19 05:31:46.541: ERROR/AndroidRuntime(770): at com.google.android.maps.PixelConverter.toPixels(PixelConverter.java:48) 01-19 05:31:46.541: ERROR/AndroidRuntime(770): at pro.googlemapp.LocationActivity$MyLocationOverlay.draw(LocationActivity.java:101) 01-19 05:31:46.541: ERROR/AndroidRuntime(770): at com.google.android.maps.OverlayBundle.draw(OverlayBundle.java:42) 01-19 05:31:46.541: ERROR/AndroidRuntime(770): at com.google.android.maps.MapView.onDraw(MapView.java:476) 01-19 05:31:46.541: ERROR/AndroidRuntime(770): at android.view.View.draw(View.java:6274) 01-19 05:31:46.541: ERROR/AndroidRuntime(770): at android.view.ViewGroup.drawChild(ViewGroup.java:1526) 01-19 05:31:46.541: ERROR/AndroidRuntime(770): at android.view.ViewGroup.dispatchDraw(ViewGroup.java:1256) 01-19 05:31:46.541: ERROR/AndroidRuntime(770): at android.view.ViewGroup.drawChild(ViewGroup.java:1524) 01-19 05:31:46.541: ERROR/AndroidRuntime(770): at android.view.ViewGroup.dispatchDraw(ViewGroup.java:1256) 01-19 05:31:46.541: ERROR/AndroidRuntime(770): at android.view.View.draw(View.java:6277) 01-19 05:31:46.541: ERROR/AndroidRuntime(770): at android.widget.FrameLayout.draw(FrameLayout.java:352) 01-19 05:31:46.541: ERROR/AndroidRuntime(770): at android.view.ViewGroup.drawChild(ViewGroup.java:1526) 01-19 05:31:46.541: ERROR/AndroidRuntime(770): at android.view.ViewGroup.dispatchDraw(ViewGroup.java:1256) 01-19 05:31:46.541: ERROR/AndroidRuntime(770): at android.view.ViewGroup.drawChild(ViewGroup.java:1524) 01-19 05:31:46.541: ERROR/AndroidRuntime(770): at android.view.ViewGroup.dispatchDraw(ViewGroup.java:1256) 01-19 05:31:46.541: ERROR/AndroidRuntime(770): at android.view.View.draw(View.java:6277) 01-19 05:31:46.541: ERROR/AndroidRuntime(770): at android.widget.FrameLayout.draw(FrameLayout.java:352) 01-19 05:31:46.541: ERROR/AndroidRuntime(770): at com.android.internal.policy.impl.PhoneWindow$DecorView.draw(PhoneWindow.java:1883) 01-19 05:31:46.541: ERROR/AndroidRuntime(770): at android.view.ViewRoot.draw(ViewRoot.java:1332) 01-19 05:31:46.541: ERROR/AndroidRuntime(770): at android.view.ViewRoot.performTraversals(ViewRoot.java:1097) 01-19 05:31:46.541: ERROR/AndroidRuntime(770): at android.view.ViewRoot.handleMessage(ViewRoot.java:1613) 01-19 05:31:46.541: ERROR/AndroidRuntime(770): at android.os.Handler.dispatchMessage(Handler.java:99) 01-19 05:31:46.541: ERROR/AndroidRuntime(770): at android.os.Looper.loop(Looper.java:123) 01-19 05:31:46.541: ERROR/AndroidRuntime(770): at android.app.ActivityThread.main(ActivityThread.java:4203) 01-19 05:31:46.541: ERROR/AndroidRuntime(770): at java.lang.reflect.Method.invokeNative(Native Method) 01-19 05:31:46.541: ERROR/AndroidRuntime(770): at java.lang.reflect.Method.invoke(Method.java:521) 01-19 05:31:46.541: ERROR/AndroidRuntime(770): at com.android.internal.os.ZygoteInit$MethodAndArgsCaller.run(ZygoteInit.java:791) 01-19 05:31:46.541: ERROR/AndroidRuntime(770): at com.android.internal.os.ZygoteInit.main(ZygoteInit.java:549) 01-19 05:31:46.541: ERROR/AndroidRuntime(770): at dalvik.system.NativeStart.main(Native Method) 01-19 05:31:46.551: INFO/Process(583): Sending signal. PID: 770 SIG: 3 01-19 05:31:46.581: INFO/dalvikvm(770): threadid=7: reacting to signal 3 01-19 05:31:46.661: INFO/dalvikvm(770): Wrote stack trace to '/data/anr/traces.txt' 01-19 05:31:46.871: INFO/ARMAssembler(583): generated scanline__00000077:03515104_00000000_00000000 [ 27 ipp] (41 ins) at [0x2c69c8:0x2c6a6c] in 973448 ns 01-19 05:31:46.911: INFO/ARMAssembler(583): generated scanline__00000077:03515104_00001001_00000000 [ 64 ipp] (84 ins) at [0x2c6a70:0x2c6bc0] in 1985378 ns 01-19 05:31:49.881: INFO/Process(770): Sending signal. PID: 770 SIG: 9 01-19 05:31:49.931: INFO/ActivityManager(583): Process pro.googlemapp (pid 770) has died. 01-19 05:31:49.941: WARN/GpsLocationProvider(583): Unneeded remove listener for uid 1000 01-19 05:31:49.941: DEBUG/GpsLocationProvider(583): stopNavigating 01-19 05:31:49.951: INFO/WindowManager(583): WIN DEATH: Window{438891c0 pro.googlemapp/pro.googlemapp.LocationActivity paused=false} 01-19 05:31:50.111: WARN/UsageStats(583): Unexpected resume of com.android.launcher while already resumed in pro.googlemapp 01-19 05:31:50.200: WARN/InputManagerService(583): Got RemoteException sending setActive(false) notification to pid 770 uid 10025

    Read the article

  • How to fix a Sticky Footer that works, but after a browser window is resized, the footer overlaps.

    - by UXdesigner
    Good day, I've been trying to build a perfect footer who sticks at the bottom of the browser window after it's content. And I got help here @ Stack Overflow previously. But after a while, and doing a few tests, found out that after the browser window is resized, and then I scroll down , the footer overlaps...it is causing me a big headache right now and I'd like to fix this so I can move on. I'm going to post the display.css right here: @charset "utf-8"; body, html { margin: 0; padding: 0; text-align: center; position: relative; min-height:100%; /* needed for footer positioning*/ height:100%; /* needed for footer positioning*/ } .spacer { clear: both; height: 0; margin: 0; padding: 0; font-size: 0.1em; } .spacer_left { clear: left; margin: 0 0 10px 0; padding: 0; font-size: 0.1em; } hr { height: 1px; margin: 20px 0 20px 0; border: 0; color: #ccc; background: #ccc; } #container { position:relative; /* needed for footer positioning*/ min-height: 100%;/* needed for footer positioning*/ height: auto !important;/* needed for footer positioning*/ height: 100%;/* needed for footer positioning*/ margin: 0 auto -30px;/* needed for footer positioning*/ width: 1160px; padding: 0; border: 1px solid #333; text-align: left; } #header { margin: 0; padding: 5px; height:70px; } #login { font-family: Arial; font-size: 15px; color:#FFF; text-align: right; width: 440px; margin: 2px; } #login .theInput { font-family: Arial; font-size: 14px; width: 110px; margin-right: 5px; } #login .theSubmit { font-family: Arial; font-size: 10px; background-color: #333333; color: #FFFFFF; margin-right: 5px; } h1#lineainvisible { width:1160px; height:4px; position:relative; margin-top:4px; visibility: inherit; font-family:Arial, Helvetica, sans-serif; font-size:12px; } ul#nav { width:100%; height:36px; display:block; background-color:#000; background-repeat:repeat-x; } #wrapthatbanner { display:block; float:left; width:100%; height:524px; margin-bottom:20px; } #content { margin: 0px 20px 30px 20px; /* needed for footer positioning*/ } .panelsreadmore { margin-right: 10px; text-align:right; } div#content.columns { margin-left: 100px; } #content abbr, #content acronym { cursor: help; border-bottom: 1px dotted; } #content ul { list-style-type: square; margin-left: 75px; } #content ul li, #content ol li { margin: 0 0 0.4em 0; padding: 0; } #content blockquote { width: 75%; margin: 0 auto; padding: 20px; } #contentLeft { float: left; width:580px; } #contentRight { float: right; width:580px; } .sitenote { display:block; padding:6px; border:1px solid #bae2f0; background:#e3f4f9; line-height:130%; font-size:13px; margin-top: 0; margin-right: 0; margin-bottom: 0.5em; margin-left: 0; } #footer, .push /* needed for footer positioning*/ { padding: 5px; clear: both; position:absolute;/* needed for footer positioning*/ bottom:0;/* needed for footer positioning*/ height: -30px;/* needed for footer positioning*/ width:1150px; } And this is the HTML Template File. <!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Strict//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-strict.dtd"> <html xmlns="http://www.w3.org/1999/xhtml"> <head> <!-- TemplateBeginEditable name="doctitle" --> <title>Title of Page</title> <!-- TemplateEndEditable --> <!-- TemplateParam name="categoria" type="text" value="home" --> <!-- Meta Tags --> <meta http-equiv="Content-Type" content="text/html; charset=utf-8" /> <!-- Meta Tags - Close --> <!-- CSS Loader - StartsS --> <link href="../css/main-client.css" rel="stylesheet" type="text/css" media="all" /> <!-- CSS Loader - Ends --> <!-- Drop Down Menu --> <link href="../css/dropdown.css" media="screen" rel="stylesheet" type="text/css" /> <link href="../css/default.advanced.css" media="screen" rel="stylesheet" type="text/css" /> <!-- Drop Down Menu - Ends --> <!-- Font Replacement Starts --> <script src="../cufon-yui.js" type="text/javascript"></script> <script src="../AFB_400.font.js" type="text/javascript"></script> <script type="text/javascript"> Cufon.replace('h2'); </script> <script type="text/javascript"> Cufon.replace('h3'); </script> <script type="text/javascript"> Cufon.replace('h4'); </script> <!-- Font Replacement = END --> <!-- Start VisualLightBox.com HEAD section --> <link rel="stylesheet" href="engine/css/vlightbox.css" type="text/css" /> <style type="text/css">#vlightbox a#vlb{display:none}</style> <link rel="stylesheet" href="engine/css/visuallightbox.css" type="text/css" media="screen" /> <script src="engine/js/jquery.min.js" type="text/javascript"></script> <!-- End VisualLightBox.com HEAD section --> <!-- TemplateBeginEditable name="head" --> <!-- TemplateEndEditable --> </head> <body id="@@(categoria)@@"> <div id="container"> <div id="header"> <table width="100%" border="0"> <tr> <td width="67%" height="77px;"><a href="index.html"><img src="../images/Titulos/5.png" alt="" width="257" hspace="10" vspace="10" border="0" id="screen_logo" title=""/></a></td> <td width="33%" valign="top"><form id="login">Log in: <input type="text" class="theInput" name="user" /> <input type="submit" name="Submit" value="Submit" /> </form> </td> </tr> </table> </div> <!-- Aqui es donde empieza fisicamente el menu drop down --> <ul id="nav" class="dropdown dropdown-horizontal"> <li><a href="../index.html">Home</a></li> <li><a href="#" class="dir">Service 1</a></li> <li><a href="#" class="dir">Service 2</a></li> <li><a href="#" class="dir">Service 3</a></li> <li><a href="#" class="dir">Service 4</a></li> <li><a href="#" class="dir">Service 5</a></li> <li><a href="#" class="dir">Service 6</a></li> </ul> <!-- Aqui termina el menu CSS--> <!-- Reset --> <div id="wmfg"> </div> <!-- Reset --> <!-- TemplateBeginEditable name="banner-grande" --> <!-- TemplateEndEditable --> <div id="content"><!-- TemplateBeginEditable name="content" --> <p>&nbsp;</p> <!-- TemplateEndEditable --></div> <div id="footer"><a href="../terms.html">Terms and Conditions</a> |<a href="privacy.html"> Privacy Policy</a><br/> Copyright 2010. .</div> </div> </div> </body> </html> Can somebody take a look at this, and tell me what am I doing wrong ? Thanks in advance.

    Read the article

  • android app working on simulator but not on phone

    - by raqz
    i have this app that i developed and it works great on the simulator with no errors what so ever. but the moment i try to run the same on the phone for testing, the app crashes stating filenotfoundexception. it says the file /res/drawable/divider_horizontal.9.png is missing. but actually speaking, i have never referenced that file through my code. i believe its a system/os file that is unavailable. i have a custom list view, i guess its the divider there... could somebody please suggest what is wrong here. i believe this is a similar issue discussed here..but i am unable to make any sense out of it http://code.google.com/p/transdroid/issues/detail?id=14 the listview.xml layout file <?xml version="1.0" encoding="utf-8"?> <LinearLayout xmlns:android="http://schemas.android.com/apk/res/android" android:layout_height="wrap_content" android:gravity="left|center" android:layout_width="wrap_content" android:paddingBottom="5px" android:paddingTop="5px" android:paddingLeft="5px" > <ImageView android:id="@+id/linkImage" android:layout_width="wrap_content" android:layout_height="fill_parent" android:layout_marginRight="6dip" android:src="@drawable/icon" /> <LinearLayout android:orientation="vertical" android:layout_width="0dip" android:layout_weight="1" android:layout_height="fill_parent"> <TextView android:id="@+id/firstLineView" android:layout_width="wrap_content" android:layout_height="wrap_content" android:gravity="center" android:textColor="#FFFF00" android:text="first line title"></TextView> <TextView android:id="@+id/secondLineView" android:layout_width="wrap_content" android:layout_height="wrap_content" android:text="second line title" android:layout_marginLeft="10px" android:gravity="center" android:textColor="#0099CC"></TextView> </LinearLayout> </LinearLayout> the main xml file that calls the listview.xml <?xml version="1.0" encoding="UTF-8"?> <FrameLayout xmlns:android="http://schemas.android.com/apk/res/android" android:layout_width="fill_parent" android:layout_height="fill_parent"> <LinearLayout android:orientation="vertical" android:layout_width="fill_parent" android:layout_height="fill_parent"> <LinearLayout android:orientation="horizontal" android:layout_width="fill_parent" android:layout_height="40px"> <Button android:id="@+id/todayButton" android:layout_width="fill_parent" android:layout_height="fill_parent" android:text="Today" android:textSize="12sp" android:gravity="center" android:layout_weight="1" /> <Button android:id="@+id/tomorrowButton" android:layout_width="fill_parent" android:layout_height="fill_parent" android:text="Tomorrow" android:textSize="12sp" android:layout_weight="1" /> <Button android:id="@+id/WeekButton" android:layout_width="fill_parent" android:layout_height="fill_parent" android:text="Future" android:textSize="12sp" android:layout_weight="1" /> </LinearLayout> <LinearLayout android:id="@+id/listLayout" android:orientation="vertical" android:layout_width="fill_parent" android:layout_height="fill_parent"> <ListView android:id="@+id/ListView01" android:layout_width="fill_parent" android:layout_height="fill_parent" /> <TextView android:id="@id/android:empty" android:layout_width="fill_parent" android:layout_height="fill_parent" android:text="No Results" /> </LinearLayout> </LinearLayout> </FrameLayout> and the code for the same is private class EfficientAdapter extends BaseAdapter{ private LayoutInflater mInflater; private String eventTitleArray[]; private String eventDateArray[]; private String eventImageLinkArray[]; public EfficientAdapter(Context context,String[] eventTitleArray,String[] eventDateArray, String[] eventImageLinkArray){ mInflater = LayoutInflater.from(context); this.eventDateArray=eventDateArray; this.eventTitleArray=eventTitleArray; this.eventImageLinkArray =eventImageLinkArray; } public int getCount(){ //return XmlParser.todayEvents.size()-1; return this.eventDateArray.length; } public Object getItem(int position){ return position; } public long getItemId(int position){ return position; } public View getView(int position, View convertView, ViewGroup parent){ ViewHolder holder; if(convertView == null){ convertView = mInflater.inflate(R.layout.listview,null); holder = new ViewHolder(); holder.firstLine = (TextView) convertView.findViewById(R.id.firstLineView); holder.secondLine = (TextView) convertView.findViewById(R.id.secondLineView); holder.imageView = (ImageView) convertView.findViewById(R.id.linkImage); //holder.checkbox = (CheckBox) convertView.findViewById(R.id.star); holder.firstLine.setFocusable(false); holder.secondLine.setFocusable(false); holder.imageView.setFocusable(false); //holder.checkbox.setFocusable(false); convertView.setTag(holder); }else{ holder = (ViewHolder) convertView.getTag(); } Log.i(tag, "Creating the list"); holder.firstLine.setText(this.eventTitleArray[position]); holder.secondLine.setText(this.eventDateArray[position]); Bitmap bitmap; try { bitmap = BitmapFactory.decodeStream((InputStream)new URL("http://eventur.sis.pitt.edu/images/heinz7.jpg").getContent()); } catch (MalformedURLException e1) { // TODO Auto-generated catch block e1.printStackTrace(); } catch (Exception e1) { // TODO Auto-generated catch block bitmap = BitmapFactory.decodeFile("assets/heinz7.jpg");//decodeFile(getResources().getAssets().open("icon.png")); e1.printStackTrace(); } try { try{ bitmap = BitmapFactory.decodeStream((InputStream)new URL(this.eventImageLinkArray[position]).getContent());} catch(Exception e){ bitmap = BitmapFactory.decodeStream((InputStream)new URL("http://eventur.sis.pitt.edu/images/heinz7.jpg").getContent()); } int width = 0; int height =0; int newWidth = 50; int newHeight = 40; try{ width = bitmap.getWidth(); height = bitmap.getHeight(); } catch(Exception e){ width = 50; height = 40; } float scaleWidth = ((float)newWidth)/width; float scaleHeight = ((float)newHeight)/height; Matrix mat = new Matrix(); mat.postScale(scaleWidth, scaleHeight); try{ Bitmap newBitmap = Bitmap.createBitmap(bitmap,0,0,width,height,mat,true); BitmapDrawable bmd = new BitmapDrawable(newBitmap); holder.imageView.setImageDrawable(bmd); holder.imageView.setScaleType(ScaleType.CENTER); } catch(Exception e){ } } catch (MalformedURLException e) { // TODO Auto-generated catch block e.printStackTrace(); } catch (IOException e) { // TODO Auto-generated catch block e.printStackTrace(); } return convertView; } class ViewHolder{ TextView firstLine; TextView secondLine; ImageView imageView; //CheckBox checkbox; } The stack trace 12-12 22:55:25.022: ERROR/AndroidRuntime(11069): Uncaught handler: thread main exiting due to uncaught exception 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): android.view.InflateException: Binary XML file line #6: Error inflating class java.lang.reflect.Constructor 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at android.view.LayoutInflater.createView(LayoutInflater.java:512) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at com.android.internal.policy.impl.PhoneLayoutInflater.onCreateView(PhoneLayoutInflater.java:56) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at android.view.LayoutInflater.createViewFromTag(LayoutInflater.java:562) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at android.view.LayoutInflater.rInflate(LayoutInflater.java:617) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at android.view.LayoutInflater.inflate(LayoutInflater.java:407) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at android.view.LayoutInflater.inflate(LayoutInflater.java:320) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at android.view.LayoutInflater.inflate(LayoutInflater.java:276) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at com.eventur.MainActivity$EfficientAdapter.getView(MainActivity.java:566) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at android.widget.AbsListView.obtainView(AbsListView.java:1274) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at android.widget.ListView.makeAndAddView(ListView.java:1661) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at android.widget.ListView.fillDown(ListView.java:610) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at android.widget.ListView.fillFromTop(ListView.java:673) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at android.widget.ListView.layoutChildren(ListView.java:1519) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at android.widget.AbsListView.onLayout(AbsListView.java:1113) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at android.view.View.layout(View.java:6156) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at android.widget.LinearLayout.setChildFrame(LinearLayout.java:1119) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at android.widget.LinearLayout.layoutVertical(LinearLayout.java:998) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at android.widget.LinearLayout.onLayout(LinearLayout.java:918) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at android.view.View.layout(View.java:6156) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at android.widget.LinearLayout.setChildFrame(LinearLayout.java:1119) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at android.widget.LinearLayout.layoutVertical(LinearLayout.java:998) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at android.widget.LinearLayout.onLayout(LinearLayout.java:918) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at android.view.View.layout(View.java:6156) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at android.widget.FrameLayout.onLayout(FrameLayout.java:333) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at android.view.View.layout(View.java:6156) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at android.widget.FrameLayout.onLayout(FrameLayout.java:333) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at android.view.View.layout(View.java:6156) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at android.widget.LinearLayout.setChildFrame(LinearLayout.java:1119) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at android.widget.LinearLayout.layoutVertical(LinearLayout.java:998) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at android.widget.LinearLayout.onLayout(LinearLayout.java:918) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at android.view.View.layout(View.java:6156) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at android.widget.FrameLayout.onLayout(FrameLayout.java:333) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at android.view.View.layout(View.java:6156) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at android.view.ViewRoot.performTraversals(ViewRoot.java:950) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at android.view.ViewRoot.handleMessage(ViewRoot.java:1529) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at android.os.Handler.dispatchMessage(Handler.java:99) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at android.os.Looper.loop(Looper.java:123) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at android.app.ActivityThread.main(ActivityThread.java:3977) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at java.lang.reflect.Method.invokeNative(Native Method) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at java.lang.reflect.Method.invoke(Method.java:521) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at com.android.internal.os.ZygoteInit$MethodAndArgsCaller.run(ZygoteInit.java:782) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at com.android.internal.os.ZygoteInit.main(ZygoteInit.java:540) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at dalvik.system.NativeStart.main(Native Method) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): Caused by: java.lang.reflect.InvocationTargetException 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at android.widget.ImageView.<init>(ImageView.java:128) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at java.lang.reflect.Constructor.constructNative(Native Method) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at java.lang.reflect.Constructor.newInstance(Constructor.java:446) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at android.view.LayoutInflater.createView(LayoutInflater.java:499) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): ... 42 more 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): Caused by: android.content.res.Resources$NotFoundException: File res/drawable/divider_horizontal_dark.9.png from drawable resource ID #0x7f020001 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at android.content.res.Resources.loadDrawable(Resources.java:1643) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at android.content.res.TypedArray.getDrawable(TypedArray.java:548) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at android.widget.ImageView.<init>(ImageView.java:138) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): ... 46 more 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): Caused by: java.io.FileNotFoundException: res/drawable/divider_horizontal_dark.9.png 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at android.content.res.AssetManager.openNonAssetNative(Native Method) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at android.content.res.AssetManager.openNonAsset(AssetManager.java:417) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): at android.content.res.Resources.loadDrawable(Resources.java:1636) 12-12 22:55:25.212: ERROR/AndroidRuntime(11069): ... 48 more

    Read the article

  • Conflict between two Javascripts (MailChimp validation etc. scripts & jQuery hSlides.js)

    - by Brian
    I have two scripts running on the same page, one is the jQuery.hSlides.js script http://www.jesuscarrera.info/demos/hslides/ and the other is a custom script that is used for MailChimp list signup integration. The hSlides panel can be seen in effect here: http://theatricalbellydance.com. I've turned off the MailChimp script because it was conflicting with the hSlides script, causing it not to to fail completely (as seen here http://theatricalbellydance.com/home2/). Can someone tell me what could be done to the hSlides script to stop the conflict with the MailChimp script? The MailChimp Script var fnames = new Array(); var ftypes = new Array(); fnames[0] = 'EMAIL'; ftypes[0] = 'email'; fnames[3] = 'MMERGE3'; ftypes[3] = 'text'; fnames[1] = 'FNAME'; ftypes[1] = 'text'; fnames[2] = 'LNAME'; ftypes[2] = 'text'; fnames[4] = 'MMERGE4'; ftypes[4] = 'address'; fnames[6] = 'MMERGE6'; ftypes[6] = 'number'; fnames[9] = 'MMERGE9'; ftypes[9] = 'text'; fnames[5] = 'MMERGE5'; ftypes[5] = 'text'; fnames[7] = 'MMERGE7'; ftypes[7] = 'text'; fnames[8] = 'MMERGE8'; ftypes[8] = 'text'; fnames[10] = 'MMERGE10'; ftypes[10] = 'text'; fnames[11] = 'MMERGE11'; ftypes[11] = 'text'; fnames[12] = 'MMERGE12'; ftypes[12] = 'text'; var err_style = ''; try { err_style = mc_custom_error_style; } catch (e) { err_style = 'margin: 1em 0 0 0; padding: 1em 0.5em 0.5em 0.5em; background: rgb(255, 238, 238) none repeat scroll 0% 0%; font-weight: bold; float: left; z-index: 1; width: 80%; -moz-background-clip: -moz-initial; -moz-background-origin: -moz-initial; -moz-background-inline-policy: -moz-initial; color: rgb(255, 0, 0);'; } var mce_jQuery = jQuery.noConflict(); mce_jQuery(document).ready(function ($) { var options = { errorClass: 'mce_inline_error', errorElement: 'div', errorStyle: err_style, onkeyup: function () {}, onfocusout: function () {}, onblur: function () {} }; var mce_validator = mce_jQuery("#mc-embedded-subscribe-form").validate(options); options = { url: 'http://theatricalbellydance.us1.list-manage.com/subscribe/post-json?u=1d127e7630ced825cb1a8b5a9&id=9f12d2a6bb&c=?', type: 'GET', dataType: 'json', contentType: "application/json; charset=utf-8", beforeSubmit: function () { mce_jQuery('#mce_tmp_error_msg').remove(); mce_jQuery('.datefield', '#mc_embed_signup').each(function () { var txt = 'filled'; var fields = new Array(); var i = 0; mce_jQuery(':text', this).each(function () { fields[i] = this; i++; }); mce_jQuery(':hidden', this).each(function () { if (fields[0].value == 'MM' && fields[1].value == 'DD' && fields[2].value == 'YYYY') { this.value = ''; } else if (fields[0].value == '' && fields[1].value == '' && fields[2].value == '') { this.value = ''; } else { this.value = fields[0].value + '/' + fields[1].value + '/' + fields[2].value; } }); }); return mce_validator.form(); }, success: mce_success_cb }; mce_jQuery('#mc-embedded-subscribe-form').ajaxForm(options); }); function mce_success_cb(resp) { mce_jQuery('#mce-success-response').hide(); mce_jQuery('#mce-error-response').hide(); if (resp.result == "success") { mce_jQuery('#mce-' + resp.result + '-response').show(); mce_jQuery('#mce-' + resp.result + '-response').html(resp.msg); mce_jQuery('#mc-embedded-subscribe-form').each(function () { this.reset(); }); } else { var index = -1; var msg; try { var parts = resp.msg.split(' - ', 2); if (parts[1] == undefined) { msg = resp.msg; } else { i = parseInt(parts[0]); if (i.toString() == parts[0]) { index = parts[0]; msg = parts[1]; } else { index = -1; msg = resp.msg; } } } catch (e) { index = -1; msg = resp.msg; } try { if (index == -1) { mce_jQuery('#mce-' + resp.result + '-response').show(); mce_jQuery('#mce-' + resp.result + '-response').html(msg); } else { err_id = 'mce_tmp_error_msg'; html = '<div id="' + err_id + '" style="' + err_style + '"> ' + msg + '</div>'; var input_id = '#mc_embed_signup'; var f = mce_jQuery(input_id); if (ftypes[index] == 'address') { input_id = '#mce-' + fnames[index] + '-addr1'; f = mce_jQuery(input_id).parent().parent().get(0); } else if (ftypes[index] == 'date') { input_id = '#mce-' + fnames[index] + '-month'; f = mce_jQuery(input_id).parent().parent().get(0); } else { input_id = '#mce-' + fnames[index]; f = mce_jQuery().parent(input_id).get(0); } if (f) { mce_jQuery(f).append(html); mce_jQuery(input_id).focus(); } else { mce_jQuery('#mce-' + resp.result + '-response').show(); mce_jQuery('#mce-' + resp.result + '-response').html(msg); } } } catch (e) { mce_jQuery('#mce-' + resp.result + '-response').show(); mce_jQuery('#mce-' + resp.result + '-response').html(msg); } } } The hslides script: /* * hSlides (1.0) // 2008.02.25 // <http://plugins.jquery.com/project/hslides> * * REQUIRES jQuery 1.2.3+ <http://jquery.com/> * * Copyright (c) 2008 TrafficBroker <http://www.trafficbroker.co.uk> * Licensed under GPL and MIT licenses * * hSlides is an horizontal accordion navigation, sliding the panels around to reveal one of interest. * * Sample Configuration: * // this is the minimum configuration needed * $('#accordion').hSlides({ * totalWidth: 730, * totalHeight: 140, * minPanelWidth: 87, * maxPanelWidth: 425 * }); * * Config Options: * // Required configuration * totalWidth: Total width of the accordion // default: 0 * totalHeight: Total height of the accordion // default: 0 * minPanelWidth: Minimum width of the panel (closed) // default: 0 * maxPanelWidth: Maximum width of the panel (opened) // default: 0 * // Optional configuration * midPanelWidth: Middle width of the panel (centered) // default: 0 * speed: Speed for the animation // default: 500 * easing: Easing effect for the animation. Other than 'swing' or 'linear' must be provided by plugin // default: 'swing' * sensitivity: Sensitivity threshold (must be 1 or higher) // default: 3 * interval: Milliseconds for onMouseOver polling interval // default: 100 * timeout: Milliseconds delay before onMouseOut // default: 300 * eventHandler: Event to open panels: click or hover. For the hover option requires hoverIntent plugin <http://cherne.net/brian/resources/jquery.hoverIntent.html> // default: 'click' * panelSelector: HTML element storing the panels // default: 'li' * activeClass: CSS class for the active panel // default: none * panelPositioning: Accordion panelPositioning: top -> first panel on the bottom and next on the top, other value -> first panel on the top and next to the bottom // default: 'top' * // Callback funtctions. Inside them, we can refer the panel with $(this). * onEnter: Funtion raised when the panel is activated. // default: none * onLeave: Funtion raised when the panel is deactivated. // default: none * * We can override the defaults with: * $.fn.hSlides.defaults.easing = 'easeOutCubic'; * * @param settings An object with configuration options * @author Jesus Carrera <[email protected]> */ (function($) { $.fn.hSlides = function(settings) { // override default configuration settings = $.extend({}, $.fn.hSlides.defaults, settings); // for each accordion return this.each(function(){ var wrapper = this; var panelLeft = 0; var panels = $(settings.panelSelector, wrapper); var panelPositioning = 1; if (settings.panelPositioning != 'top'){ panelLeft = ($(settings.panelSelector, wrapper).length - 1) * settings.minPanelWidth; panels = $(settings.panelSelector, wrapper).reverse(); panelPositioning = -1; } // necessary styles for the wrapper $(this).css('position', 'relative').css('overflow', 'hidden').css('width', settings.totalWidth).css('height', settings.totalHeight); // set the initial position of the panels var zIndex = 0; panels.each(function(){ // necessary styles for the panels $(this).css('position', 'absolute').css('left', panelLeft).css('zIndex', zIndex).css('height', settings.totalHeight).css('width', settings.maxPanelWidth); zIndex ++; // if this panel is the activated by default, set it as active and move the next (to show this one) if ($(this).hasClass(settings.activeClass)){ $.data($(this)[0], 'active', true); if (settings.panelPositioning != 'top'){ panelLeft = ($(settings.panelSelector, wrapper).index(this) + 1) * settings.minPanelWidth - settings.maxPanelWidth; }else{ panelLeft = panelLeft + settings.maxPanelWidth; } }else{ // check if we are centering and some panel is active // this is why we can't add/remove the active class in the callbacks: positioning the panels if we have one active if (settings.midPanelWidth && $(settings.panelSelector, wrapper).hasClass(settings.activeClass) == false){ panelLeft = panelLeft + settings.midPanelWidth * panelPositioning; }else{ panelLeft = panelLeft + settings.minPanelWidth * panelPositioning; } } }); // iterates through the panels setting the active and changing the position var movePanels = function(){ // index of the new active panel var activeIndex = $(settings.panelSelector, wrapper).index(this); // iterate all panels panels.each(function(){ // deactivate if is the active if ( $.data($(this)[0], 'active') == true ){ $.data($(this)[0], 'active', false); $(this).removeClass(settings.activeClass).each(settings.onLeave); } // set position of current panel var currentIndex = $(settings.panelSelector, wrapper).index(this); panelLeft = settings.minPanelWidth * currentIndex; // if the panel is next to the active, we need to add the opened width if ( (currentIndex * panelPositioning) > (activeIndex * panelPositioning)){ panelLeft = panelLeft + (settings.maxPanelWidth - settings.minPanelWidth) * panelPositioning; } // animate $(this).animate({left: panelLeft}, settings.speed, settings.easing); }); // activate the new active panel $.data($(this)[0], 'active', true); $(this).addClass(settings.activeClass).each(settings.onEnter); }; // center the panels if configured var centerPanels = function(){ var panelLeft = 0; if (settings.panelPositioning != 'top'){ panelLeft = ($(settings.panelSelector, wrapper).length - 1) * settings.minPanelWidth; } panels.each(function(){ $(this).removeClass(settings.activeClass).animate({left: panelLeft}, settings.speed, settings.easing); if ($.data($(this)[0], 'active') == true){ $.data($(this)[0], 'active', false); $(this).each(settings.onLeave); } panelLeft = panelLeft + settings.midPanelWidth * panelPositioning ; }); }; // event handling if(settings.eventHandler == 'click'){ $(settings.panelSelector, wrapper).click(movePanels); }else{ var configHoverPanel = { sensitivity: settings.sensitivity, interval: settings.interval, over: movePanels, timeout: settings.timeout, out: function() {} } var configHoverWrapper = { sensitivity: settings.sensitivity, interval: settings.interval, over: function() {}, timeout: settings.timeout, out: centerPanels } $(settings.panelSelector, wrapper).hoverIntent(configHoverPanel); if (settings.midPanelWidth != 0){ $(wrapper).hoverIntent(configHoverWrapper); } } }); }; // invert the order of the jQuery elements $.fn.reverse = function(){ return this.pushStack(this.get().reverse(), arguments); }; // default settings $.fn.hSlides.defaults = { totalWidth: 0, totalHeight: 0, minPanelWidth: 0, maxPanelWidth: 0, midPanelWidth: 0, speed: 500, easing: 'swing', sensitivity: 3, interval: 100, timeout: 300, eventHandler: 'click', panelSelector: 'li', activeClass: false, panelPositioning: 'top', onEnter: function() {}, onLeave: function() {} }; })(jQuery);

    Read the article

  • Agile Development

    - by James Oloo Onyango
    Alot of literature has and is being written about agile developement and its surrounding philosophies. In my quest to find the best way to express the importance of agile methodologies, i have found Robert C. Martin's "A Satire Of Two Companies" to be both the most concise and thorough! Enjoy the read! Rufus Inc Project Kick Off Your name is Bob. The date is January 3, 2001, and your head still aches from the recent millennial revelry. You are sitting in a conference room with several managers and a group of your peers. You are a project team leader. Your boss is there, and he has brought along all of his team leaders. His boss called the meeting. "We have a new project to develop," says your boss's boss. Call him BB. The points in his hair are so long that they scrape the ceiling. Your boss's points are just starting to grow, but he eagerly awaits the day when he can leave Brylcream stains on the acoustic tiles. BB describes the essence of the new market they have identified and the product they want to develop to exploit this market. "We must have this new project up and working by fourth quarter October 1," BB demands. "Nothing is of higher priority, so we are cancelling your current project." The reaction in the room is stunned silence. Months of work are simply going to be thrown away. Slowly, a murmur of objection begins to circulate around the conference table.   His points give off an evil green glow as BB meets the eyes of everyone in the room. One by one, that insidious stare reduces each attendee to quivering lumps of protoplasm. It is clear that he will brook no discussion on this matter. Once silence has been restored, BB says, "We need to begin immediately. How long will it take you to do the analysis?" You raise your hand. Your boss tries to stop you, but his spitwad misses you and you are unaware of his efforts.   "Sir, we can't tell you how long the analysis will take until we have some requirements." "The requirements document won't be ready for 3 or 4 weeks," BB says, his points vibrating with frustration. "So, pretend that you have the requirements in front of you now. How long will you require for analysis?" No one breathes. Everyone looks around to see whether anyone has some idea. "If analysis goes beyond April 1, we have a problem. Can you finish the analysis by then?" Your boss visibly gathers his courage: "We'll find a way, sir!" His points grow 3 mm, and your headache increases by two Tylenol. "Good." BB smiles. "Now, how long will it take to do the design?" "Sir," you say. Your boss visibly pales. He is clearly worried that his 3 mms are at risk. "Without an analysis, it will not be possible to tell you how long design will take." BB's expression shifts beyond austere.   "PRETEND you have the analysis already!" he says, while fixing you with his vacant, beady little eyes. "How long will it take you to do the design?" Two Tylenol are not going to cut it. Your boss, in a desperate attempt to save his new growth, babbles: "Well, sir, with only six months left to complete the project, design had better take no longer than 3 months."   "I'm glad you agree, Smithers!" BB says, beaming. Your boss relaxes. He knows his points are secure. After a while, he starts lightly humming the Brylcream jingle. BB continues, "So, analysis will be complete by April 1, design will be complete by July 1, and that gives you 3 months to implement the project. This meeting is an example of how well our new consensus and empowerment policies are working. Now, get out there and start working. I'll expect to see TQM plans and QIT assignments on my desk by next week. Oh, and don't forget that your crossfunctional team meetings and reports will be needed for next month's quality audit." "Forget the Tylenol," you think to yourself as you return to your cubicle. "I need bourbon."   Visibly excited, your boss comes over to you and says, "Gosh, what a great meeting. I think we're really going to do some world shaking with this project." You nod in agreement, too disgusted to do anything else. "Oh," your boss continues, "I almost forgot." He hands you a 30-page document. "Remember that the SEI is coming to do an evaluation next week. This is the evaluation guide. You need to read through it, memorize it, and then shred it. It tells you how to answer any questions that the SEI auditors ask you. It also tells you what parts of the building you are allowed to take them to and what parts to avoid. We are determined to be a CMM level 3 organization by June!"   You and your peers start working on the analysis of the new project. This is difficult because you have no requirements. But from the 10-minute introduction given by BB on that fateful morning, you have some idea of what the product is supposed to do.   Corporate process demands that you begin by creating a use case document. You and your team begin enumerating use cases and drawing oval and stick diagrams. Philosophical debates break out among the team members. There is disagreement as to whether certain use cases should be connected with <<extends>> or <<includes>> relationships. Competing models are created, but nobody knows how to evaluate them. The debate continues, effectively paralyzing progress.   After a week, somebody finds the iceberg.com Web site, which recommends disposing entirely of <<extends>> and <<includes>> and replacing them with <<precedes>> and <<uses>>. The documents on this Web site, authored by Don Sengroiux, describes a method known as stalwart-analysis, which claims to be a step-by-step method for translating use cases into design diagrams. More competing use case models are created using this new scheme, but again, people can't agree on how to evaluate them. The thrashing continues. More and more, the use case meetings are driven by emotion rather than by reason. If it weren't for the fact that you don't have requirements, you'd be pretty upset by the lack of progress you are making. The requirements document arrives on February 15. And then again on February 20, 25, and every week thereafter. Each new version contradicts the previous one. Clearly, the marketing folks who are writing the requirements, empowered though they might be, are not finding consensus.   At the same time, several new competing use case templates have been proposed by the various team members. Each template presents its own particularly creative way of delaying progress. The debates rage on. On March 1, Prudence Putrigence, the process proctor, succeeds in integrating all the competing use case forms and templates into a single, all-encompassing form. Just the blank form is 15 pages long. She has managed to include every field that appeared on all the competing templates. She also presents a 159- page document describing how to fill out the use case form. All current use cases must be rewritten according to the new standard.   You marvel to yourself that it now requires 15 pages of fill-in-the-blank and essay questions to answer the question: What should the system do when the user presses Return? The corporate process (authored by L. E. Ott, famed author of "Holistic Analysis: A Progressive Dialectic for Software Engineers") insists that you discover all primary use cases, 87 percent of all secondary use cases, and 36.274 percent of all tertiary use cases before you can complete analysis and enter the design phase. You have no idea what a tertiary use case is. So in an attempt to meet this requirement, you try to get your use case document reviewed by the marketing department, which you hope will know what a tertiary use case is.   Unfortunately, the marketing folks are too busy with sales support to talk to you. Indeed, since the project started, you have not been able to get a single meeting with marketing, which has provided a never-ending stream of changing and contradictory requirements documents.   While one team has been spinning endlessly on the use case document, another team has been working out the domain model. Endless variations of UML documents are pouring out of this team. Every week, the model is reworked.   The team members can't decide whether to use <<interfaces>> or <<types>> in the model. A huge disagreement has been raging on the proper syntax and application of OCL. Others on the team just got back from a 5-day class on catabolism, and have been producing incredibly detailed and arcane diagrams that nobody else can fathom.   On March 27, with one week to go before analysis is to be complete, you have produced a sea of documents and diagrams but are no closer to a cogent analysis of the problem than you were on January 3. **** And then, a miracle happens.   **** On Saturday, April 1, you check your e-mail from home. You see a memo from your boss to BB. It states unequivocally that you are done with the analysis! You phone your boss and complain. "How could you have told BB that we were done with the analysis?" "Have you looked at a calendar lately?" he responds. "It's April 1!" The irony of that date does not escape you. "But we have so much more to think about. So much more to analyze! We haven't even decided whether to use <<extends>> or <<precedes>>!" "Where is your evidence that you are not done?" inquires your boss, impatiently. "Whaaa . . . ." But he cuts you off. "Analysis can go on forever; it has to be stopped at some point. And since this is the date it was scheduled to stop, it has been stopped. Now, on Monday, I want you to gather up all existing analysis materials and put them into a public folder. Release that folder to Prudence so that she can log it in the CM system by Monday afternoon. Then get busy and start designing."   As you hang up the phone, you begin to consider the benefits of keeping a bottle of bourbon in your bottom desk drawer. They threw a party to celebrate the on-time completion of the analysis phase. BB gave a colon-stirring speech on empowerment. And your boss, another 3 mm taller, congratulated his team on the incredible show of unity and teamwork. Finally, the CIO takes the stage to tell everyone that the SEI audit went very well and to thank everyone for studying and shredding the evaluation guides that were passed out. Level 3 now seems assured and will be awarded by June. (Scuttlebutt has it that managers at the level of BB and above are to receive significant bonuses once the SEI awards level 3.)   As the weeks flow by, you and your team work on the design of the system. Of course, you find that the analysis that the design is supposedly based on is flawedno, useless; no, worse than useless. But when you tell your boss that you need to go back and work some more on the analysis to shore up its weaker sections, he simply states, "The analysis phase is over. The only allowable activity is design. Now get back to it."   So, you and your team hack the design as best you can, unsure of whether the requirements have been properly analyzed. Of course, it really doesn't matter much, since the requirements document is still thrashing with weekly revisions, and the marketing department still refuses to meet with you.     The design is a nightmare. Your boss recently misread a book named The Finish Line in which the author, Mark DeThomaso, blithely suggested that design documents should be taken down to code-level detail. "If we are going to be working at that level of detail," you ask, "why don't we simply write the code instead?" "Because then you wouldn't be designing, of course. And the only allowable activity in the design phase is design!" "Besides," he continues, "we have just purchased a companywide license for Dandelion! This tool enables 'Round the Horn Engineering!' You are to transfer all design diagrams into this tool. It will automatically generate our code for us! It will also keep the design diagrams in sync with the code!" Your boss hands you a brightly colored shrinkwrapped box containing the Dandelion distribution. You accept it numbly and shuffle off to your cubicle. Twelve hours, eight crashes, one disk reformatting, and eight shots of 151 later, you finally have the tool installed on your server. You consider the week your team will lose while attending Dandelion training. Then you smile and think, "Any week I'm not here is a good week." Design diagram after design diagram is created by your team. Dandelion makes it very difficult to draw these diagrams. There are dozens and dozens of deeply nested dialog boxes with funny text fields and check boxes that must all be filled in correctly. And then there's the problem of moving classes between packages. At first, these diagram are driven from the use cases. But the requirements are changing so often that the use cases rapidly become meaningless. Debates rage about whether VISITOR or DECORATOR design patterns should be used. One developer refuses to use VISITOR in any form, claiming that it's not a properly object-oriented construct. Someone refuses to use multiple inheritance, since it is the spawn of the devil. Review meetings rapidly degenerate into debates about the meaning of object orientation, the definition of analysis versus design, or when to use aggregation versus association. Midway through the design cycle, the marketing folks announce that they have rethought the focus of the system. Their new requirements document is completely restructured. They have eliminated several major feature areas and replaced them with feature areas that they anticipate customer surveys will show to be more appropriate. You tell your boss that these changes mean that you need to reanalyze and redesign much of the system. But he says, "The analysis phase is system. But he says, "The analysis phase is over. The only allowable activity is design. Now get back to it."   You suggest that it might be better to create a simple prototype to show to the marketing folks and even some potential customers. But your boss says, "The analysis phase is over. The only allowable activity is design. Now get back to it." Hack, hack, hack, hack. You try to create some kind of a design document that might reflect the new requirements documents. However, the revolution of the requirements has not caused them to stop thrashing. Indeed, if anything, the wild oscillations of the requirements document have only increased in frequency and amplitude.   You slog your way through them.   On June 15, the Dandelion database gets corrupted. Apparently, the corruption has been progressive. Small errors in the DB accumulated over the months into bigger and bigger errors. Eventually, the CASE tool just stopped working. Of course, the slowly encroaching corruption is present on all the backups. Calls to the Dandelion technical support line go unanswered for several days. Finally, you receive a brief e-mail from Dandelion, informing you that this is a known problem and that the solution is to purchase the new version, which they promise will be ready some time next quarter, and then reenter all the diagrams by hand.   ****   Then, on July 1 another miracle happens! You are done with the design!   Rather than go to your boss and complain, you stock your middle desk drawer with some vodka.   **** They threw a party to celebrate the on-time completion of the design phase and their graduation to CMM level 3. This time, you find BB's speech so stirring that you have to use the restroom before it begins. New banners and plaques are all over your workplace. They show pictures of eagles and mountain climbers, and they talk about teamwork and empowerment. They read better after a few scotches. That reminds you that you need to clear out your file cabinet to make room for the brandy. You and your team begin to code. But you rapidly discover that the design is lacking in some significant areas. Actually, it's lacking any significance at all. You convene a design session in one of the conference rooms to try to work through some of the nastier problems. But your boss catches you at it and disbands the meeting, saying, "The design phase is over. The only allowable activity is coding. Now get back to it."   ****   The code generated by Dandelion is really hideous. It turns out that you and your team were using association and aggregation the wrong way, after all. All the generated code has to be edited to correct these flaws. Editing this code is extremely difficult because it has been instrumented with ugly comment blocks that have special syntax that Dandelion needs in order to keep the diagrams in sync with the code. If you accidentally alter one of these comments, the diagrams will be regenerated incorrectly. It turns out that "Round the Horn Engineering" requires an awful lot of effort. The more you try to keep the code compatible with Dandelion, the more errors Dandelion generates. In the end, you give up and decide to keep the diagrams up to date manually. A second later, you decide that there's no point in keeping the diagrams up to date at all. Besides, who has time?   Your boss hires a consultant to build tools to count the number of lines of code that are being produced. He puts a big thermometer graph on the wall with the number 1,000,000 on the top. Every day, he extends the red line to show how many lines have been added. Three days after the thermometer appears on the wall, your boss stops you in the hall. "That graph isn't growing quickly enough. We need to have a million lines done by October 1." "We aren't even sh-sh-sure that the proshect will require a m-million linezh," you blather. "We have to have a million lines done by October 1," your boss reiterates. His points have grown again, and the Grecian formula he uses on them creates an aura of authority and competence. "Are you sure your comment blocks are big enough?" Then, in a flash of managerial insight, he says, "I have it! I want you to institute a new policy among the engineers. No line of code is to be longer than 20 characters. Any such line must be split into two or more preferably more. All existing code needs to be reworked to this standard. That'll get our line count up!"   You decide not to tell him that this will require two unscheduled work months. You decide not to tell him anything at all. You decide that intravenous injections of pure ethanol are the only solution. You make the appropriate arrangements. Hack, hack, hack, and hack. You and your team madly code away. By August 1, your boss, frowning at the thermometer on the wall, institutes a mandatory 50-hour workweek.   Hack, hack, hack, and hack. By September 1st, the thermometer is at 1.2 million lines and your boss asks you to write a report describing why you exceeded the coding budget by 20 percent. He institutes mandatory Saturdays and demands that the project be brought back down to a million lines. You start a campaign of remerging lines. Hack, hack, hack, and hack. Tempers are flaring; people are quitting; QA is raining trouble reports down on you. Customers are demanding installation and user manuals; salespeople are demanding advance demonstrations for special customers; the requirements document is still thrashing, the marketing folks are complaining that the product isn't anything like they specified, and the liquor store won't accept your credit card anymore. Something has to give.    On September 15, BB calls a meeting. As he enters the room, his points are emitting clouds of steam. When he speaks, the bass overtones of his carefully manicured voice cause the pit of your stomach to roll over. "The QA manager has told me that this project has less than 50 percent of the required features implemented. He has also informed me that the system crashes all the time, yields wrong results, and is hideously slow. He has also complained that he cannot keep up with the continuous train of daily releases, each more buggy than the last!" He stops for a few seconds, visibly trying to compose himself. "The QA manager estimates that, at this rate of development, we won't be able to ship the product until December!" Actually, you think it's more like March, but you don't say anything. "December!" BB roars with such derision that people duck their heads as though he were pointing an assault rifle at them. "December is absolutely out of the question. Team leaders, I want new estimates on my desk in the morning. I am hereby mandating 65-hour work weeks until this project is complete. And it better be complete by November 1."   As he leaves the conference room, he is heard to mutter: "Empowermentbah!" * * * Your boss is bald; his points are mounted on BB's wall. The fluorescent lights reflecting off his pate momentarily dazzle you. "Do you have anything to drink?" he asks. Having just finished your last bottle of Boone's Farm, you pull a bottle of Thunderbird from your bookshelf and pour it into his coffee mug. "What's it going to take to get this project done? " he asks. "We need to freeze the requirements, analyze them, design them, and then implement them," you say callously. "By November 1?" your boss exclaims incredulously. "No way! Just get back to coding the damned thing." He storms out, scratching his vacant head.   A few days later, you find that your boss has been transferred to the corporate research division. Turnover has skyrocketed. Customers, informed at the last minute that their orders cannot be fulfilled on time, have begun to cancel their orders. Marketing is re-evaluating whether this product aligns with the overall goals of the company. Memos fly, heads roll, policies change, and things are, overall, pretty grim. Finally, by March, after far too many sixty-five hour weeks, a very shaky version of the software is ready. In the field, bug-discovery rates are high, and the technical support staff are at their wits' end, trying to cope with the complaints and demands of the irate customers. Nobody is happy.   In April, BB decides to buy his way out of the problem by licensing a product produced by Rupert Industries and redistributing it. The customers are mollified, the marketing folks are smug, and you are laid off.     Rupert Industries: Project Alpha   Your name is Robert. The date is January 3, 2001. The quiet hours spent with your family this holiday have left you refreshed and ready for work. You are sitting in a conference room with your team of professionals. The manager of the division called the meeting. "We have some ideas for a new project," says the division manager. Call him Russ. He is a high-strung British chap with more energy than a fusion reactor. He is ambitious and driven but understands the value of a team. Russ describes the essence of the new market opportunity the company has identified and introduces you to Jane, the marketing manager, who is responsible for defining the products that will address it. Addressing you, Jane says, "We'd like to start defining our first product offering as soon as possible. When can you and your team meet with me?" You reply, "We'll be done with the current iteration of our project this Friday. We can spare a few hours for you between now and then. After that, we'll take a few people from the team and dedicate them to you. We'll begin hiring their replacements and the new people for your team immediately." "Great," says Russ, "but I want you to understand that it is critical that we have something to exhibit at the trade show coming up this July. If we can't be there with something significant, we'll lose the opportunity."   "I understand," you reply. "I don't yet know what it is that you have in mind, but I'm sure we can have something by July. I just can't tell you what that something will be right now. In any case, you and Jane are going to have complete control over what we developers do, so you can rest assured that by July, you'll have the most important things that can be accomplished in that time ready to exhibit."   Russ nods in satisfaction. He knows how this works. Your team has always kept him advised and allowed him to steer their development. He has the utmost confidence that your team will work on the most important things first and will produce a high-quality product.   * * *   "So, Robert," says Jane at their first meeting, "How does your team feel about being split up?" "We'll miss working with each other," you answer, "but some of us were getting pretty tired of that last project and are looking forward to a change. So, what are you people cooking up?" Jane beams. "You know how much trouble our customers currently have . . ." And she spends a half hour or so describing the problem and possible solution. "OK, wait a second" you respond. "I need to be clear about this." And so you and Jane talk about how this system might work. Some of her ideas aren't fully formed. You suggest possible solutions. She likes some of them. You continue discussing.   During the discussion, as each new topic is addressed, Jane writes user story cards. Each card represents something that the new system has to do. The cards accumulate on the table and are spread out in front of you. Both you and Jane point at them, pick them up, and make notes on them as you discuss the stories. The cards are powerful mnemonic devices that you can use to represent complex ideas that are barely formed.   At the end of the meeting, you say, "OK, I've got a general idea of what you want. I'm going to talk to the team about it. I imagine they'll want to run some experiments with various database structures and presentation formats. Next time we meet, it'll be as a group, and we'll start identifying the most important features of the system."   A week later, your nascent team meets with Jane. They spread the existing user story cards out on the table and begin to get into some of the details of the system. The meeting is very dynamic. Jane presents the stories in the order of their importance. There is much discussion about each one. The developers are concerned about keeping the stories small enough to estimate and test. So they continually ask Jane to split one story into several smaller stories. Jane is concerned that each story have a clear business value and priority, so as she splits them, she makes sure that this stays true.   The stories accumulate on the table. Jane writes them, but the developers make notes on them as needed. Nobody tries to capture everything that is said; the cards are not meant to capture everything but are simply reminders of the conversation.   As the developers become more comfortable with the stories, they begin writing estimates on them. These estimates are crude and budgetary, but they give Jane an idea of what the story will cost.   At the end of the meeting, it is clear that many more stories could be discussed. It is also clear that the most important stories have been addressed and that they represent several months worth of work. Jane closes the meeting by taking the cards with her and promising to have a proposal for the first release in the morning.   * * *   The next morning, you reconvene the meeting. Jane chooses five cards and places them on the table. "According to your estimates, these cards represent about one perfect team-week's worth of work. The last iteration of the previous project managed to get one perfect team-week done in 3 real weeks. If we can get these five stories done in 3 weeks, we'll be able to demonstrate them to Russ. That will make him feel very comfortable about our progress." Jane is pushing it. The sheepish look on her face lets you know that she knows it too. You reply, "Jane, this is a new team, working on a new project. It's a bit presumptuous to expect that our velocity will be the same as the previous team's. However, I met with the team yesterday afternoon, and we all agreed that our initial velocity should, in fact, be set to one perfectweek for every 3 real-weeks. So you've lucked out on this one." "Just remember," you continue, "that the story estimates and the story velocity are very tentative at this point. We'll learn more when we plan the iteration and even more when we implement it."   Jane looks over her glasses at you as if to say "Who's the boss around here, anyway?" and then smiles and says, "Yeah, don't worry. I know the drill by now."Jane then puts 15 more cards on the table. She says, "If we can get all these cards done by the end of March, we can turn the system over to our beta test customers. And we'll get good feedback from them."   You reply, "OK, so we've got our first iteration defined, and we have the stories for the next three iterations after that. These four iterations will make our first release."   "So," says Jane, can you really do these five stories in the next 3 weeks?" "I don't know for sure, Jane," you reply. "Let's break them down into tasks and see what we get."   So Jane, you, and your team spend the next several hours taking each of the five stories that Jane chose for the first iteration and breaking them down into small tasks. The developers quickly realize that some of the tasks can be shared between stories and that other tasks have commonalities that can probably be taken advantage of. It is clear that potential designs are popping into the developers' heads. From time to time, they form little discussion knots and scribble UML diagrams on some cards.   Soon, the whiteboard is filled with the tasks that, once completed, will implement the five stories for this iteration. You start the sign-up process by saying, "OK, let's sign up for these tasks." "I'll take the initial database generation." Says Pete. "That's what I did on the last project, and this doesn't look very different. I estimate it at two of my perfect workdays." "OK, well, then, I'll take the login screen," says Joe. "Aw, darn," says Elaine, the junior member of the team, "I've never done a GUI, and kinda wanted to try that one."   "Ah, the impatience of youth," Joe says sagely, with a wink in your direction. "You can assist me with it, young Jedi." To Jane: "I think it'll take me about three of my perfect workdays."   One by one, the developers sign up for tasks and estimate them in terms of their own perfect workdays. Both you and Jane know that it is best to let the developers volunteer for tasks than to assign the tasks to them. You also know full well that you daren't challenge any of the developers' estimates. You know these people, and you trust them. You know that they are going to do the very best they can.   The developers know that they can't sign up for more perfect workdays than they finished in the last iteration they worked on. Once each developer has filled his or her schedule for the iteration, they stop signing up for tasks.   Eventually, all the developers have stopped signing up for tasks. But, of course, tasks are still left on the board.   "I was worried that that might happen," you say, "OK, there's only one thing to do, Jane. We've got too much to do in this iteration. What stories or tasks can we remove?" Jane sighs. She knows that this is the only option. Working overtime at the beginning of a project is insane, and projects where she's tried it have not fared well.   So Jane starts to remove the least-important functionality. "Well, we really don't need the login screen just yet. We can simply start the system in the logged-in state." "Rats!" cries Elaine. "I really wanted to do that." "Patience, grasshopper." says Joe. "Those who wait for the bees to leave the hive will not have lips too swollen to relish the honey." Elaine looks confused. Everyone looks confused. "So . . .," Jane continues, "I think we can also do away with . . ." And so, bit by bit, the list of tasks shrinks. Developers who lose a task sign up for one of the remaining ones.   The negotiation is not painless. Several times, Jane exhibits obvious frustration and impatience. Once, when tensions are especially high, Elaine volunteers, "I'll work extra hard to make up some of the missing time." You are about to correct her when, fortunately, Joe looks her in the eye and says, "When once you proceed down the dark path, forever will it dominate your destiny."   In the end, an iteration acceptable to Jane is reached. It's not what Jane wanted. Indeed, it is significantly less. But it's something the team feels that can be achieved in the next 3 weeks.   And, after all, it still addresses the most important things that Jane wanted in the iteration. "So, Jane," you say when things had quieted down a bit, "when can we expect acceptance tests from you?" Jane sighs. This is the other side of the coin. For every story the development team implements,   Jane must supply a suite of acceptance tests that prove that it works. And the team needs these long before the end of the iteration, since they will certainly point out differences in the way Jane and the developers imagine the system's behaviour.   "I'll get you some example test scripts today," Jane promises. "I'll add to them every day after that. You'll have the entire suite by the middle of the iteration."   * * *   The iteration begins on Monday morning with a flurry of Class, Responsibilities, Collaborators sessions. By midmorning, all the developers have assembled into pairs and are rapidly coding away. "And now, my young apprentice," Joe says to Elaine, "you shall learn the mysteries of test-first design!"   "Wow, that sounds pretty rad," Elaine replies. "How do you do it?" Joe beams. It's clear that he has been anticipating this moment. "OK, what does the code do right now?" "Huh?" replied Elaine, "It doesn't do anything at all; there is no code."   "So, consider our task; can you think of something the code should do?" "Sure," Elaine said with youthful assurance, "First, it should connect to the database." "And thereupon, what must needs be required to connecteth the database?" "You sure talk weird," laughed Elaine. "I think we'd have to get the database object from some registry and call the Connect() method. "Ah, astute young wizard. Thou perceives correctly that we requireth an object within which we can cacheth the database object." "Is 'cacheth' really a word?" "It is when I say it! So, what test can we write that we know the database registry should pass?" Elaine sighs. She knows she'll just have to play along. "We should be able to create a database object and pass it to the registry in a Store() method. And then we should be able to pull it out of the registry with a Get() method and make sure it's the same object." "Oh, well said, my prepubescent sprite!" "Hay!" "So, now, let's write a test function that proves your case." "But shouldn't we write the database object and registry object first?" "Ah, you've much to learn, my young impatient one. Just write the test first." "But it won't even compile!" "Are you sure? What if it did?" "Uh . . ." "Just write the test, Elaine. Trust me." And so Joe, Elaine, and all the other developers began to code their tasks, one test case at a time. The room in which they worked was abuzz with the conversations between the pairs. The murmur was punctuated by an occasional high five when a pair managed to finish a task or a difficult test case.   As development proceeded, the developers changed partners once or twice a day. Each developer got to see what all the others were doing, and so knowledge of the code spread generally throughout the team.   Whenever a pair finished something significant whether a whole task or simply an important part of a task they integrated what they had with the rest of the system. Thus, the code base grew daily, and integration difficulties were minimized.   The developers communicated with Jane on a daily basis. They'd go to her whenever they had a question about the functionality of the system or the interpretation of an acceptance test case.   Jane, good as her word, supplied the team with a steady stream of acceptance test scripts. The team read these carefully and thereby gained a much better understanding of what Jane expected the system to do. By the beginning of the second week, there was enough functionality to demonstrate to Jane. She watched eagerly as the demonstration passed test case after test case. "This is really cool," Jane said as the demonstration finally ended. "But this doesn't seem like one-third of the tasks. Is your velocity slower than anticipated?"   You grimace. You'd been waiting for a good time to mention this to Jane but now she was forcing the issue. "Yes, unfortunately, we are going more slowly than we had expected. The new application server we are using is turning out to be a pain to configure. Also, it takes forever to reboot, and we have to reboot it whenever we make even the slightest change to its configuration."   Jane eyes you with suspicion. The stress of last Monday's negotiations had still not entirely dissipated. She says, "And what does this mean to our schedule? We can't slip it again, we just can't. Russ will have a fit! He'll haul us all into the woodshed and ream us some new ones."   You look Jane right in the eyes. There's no pleasant way to give someone news like this. So you just blurt out, "Look, if things keep going like they're going, we're not going to be done with everything by next Friday. Now it's possible that we'll figure out a way to go faster. But, frankly, I wouldn't depend on that. You should start thinking about one or two tasks that could be removed from the iteration without ruining the demonstration for Russ. Come hell or high water, we are going to give that demonstration on Friday, and I don't think you want us to choose which tasks to omit."   "Aw forchrisakes!" Jane barely manages to stifle yelling that last word as she stalks away, shaking her head. Not for the first time, you say to yourself, "Nobody ever promised me project management would be easy." You are pretty sure it won't be the last time, either.   Actually, things went a bit better than you had hoped. The team did, in fact, have to drop one task from the iteration, but Jane had chosen wisely, and the demonstration for Russ went without a hitch. Russ was not impressed with the progress, but neither was he dismayed. He simply said, "This is pretty good. But remember, we have to be able to demonstrate this system at the trade show in July, and at this rate, it doesn't look like you'll have all that much to show." Jane, whose attitude had improved dramatically with the completion of the iteration, responded to Russ by saying, "Russ, this team is working hard, and well. When July comes around, I am confident that we'll have something significant to demonstrate. It won't be everything, and some of it may be smoke and mirrors, but we'll have something."   Painful though the last iteration was, it had calibrated your velocity numbers. The next iteration went much better. Not because your team got more done than in the last iteration but simply because the team didn't have to remove any tasks or stories in the middle of the iteration.   By the start of the fourth iteration, a natural rhythm has been established. Jane, you, and the team know exactly what to expect from one another. The team is running hard, but the pace is sustainable. You are confident that the team can keep up this pace for a year or more.   The number of surprises in the schedule diminishes to near zero; however, the number of surprises in the requirements does not. Jane and Russ frequently look over the growing system and make recommendations or changes to the existing functionality. But all parties realize that these changes take time and must be scheduled. So the changes do not cause anyone's expectations to be violated. In March, there is a major demonstration of the system to the board of directors. The system is very limited and is not yet in a form good enough to take to the trade show, but progress is steady, and the board is reasonably impressed.   The second release goes even more smoothly than the first. By now, the team has figured out a way to automate Jane's acceptance test scripts. The team has also refactored the design of the system to the point that it is really easy to add new features and change old ones. The second release was done by the end of June and was taken to the trade show. It had less in it than Jane and Russ would have liked, but it did demonstrate the most important features of the system. Although customers at the trade show noticed that certain features were missing, they were very impressed overall. You, Russ, and Jane all returned from the trade show with smiles on your faces. You all felt as though this project was a winner.   Indeed, many months later, you are contacted by Rufus Inc. That company had been working on a system like this for its internal operations. Rufus has canceled the development of that system after a death-march project and is negotiating to license your technology for its environment.   Indeed, things are looking up!

    Read the article

< Previous Page | 199 200 201 202 203 204  | Next Page >