Search Results

Search found 27979 results on 1120 pages for 'network drive'.

Page 204/1120 | < Previous Page | 200 201 202 203 204 205 206 207 208 209 210 211  | Next Page >

• No Homegroup Computers, Network Troubleshooter Fails

  - by Mokubai

  I have a problem with my Windows 7 Homegroup, between two Windows 7 Home Premium machines. On one machine I get this: The other machine in the Homegroup is perfectly happy and is able to see and browse this faulty machine as if there is nothing wrong. The Network and Sharing Center shows that I am joined to a Homegroup on my "Home" network and nothing is out of the ordinary. I have tried leaving the Homegroup and rejoining/recreating it several times and that does nothing at all. Normal browsing to machine names and looking through folders seems to work, but it's a much more clunky way to get stuff compared to the convenience of the Homegroup facilities. Starting the troubleshooter detects some problems with a "Peer Networking" (PNRpr or something like that) service not starting but fails to fix anything. Sure enough when I go to view the services via Control Panel - Administrative Tools - Services I see that both the "Peer Name Resolution Protocol" and "Peer Networking Grouping" services are stopped. Attempting to start the "Peer Networking Grouping" gives an error that a dependency service will not start, the only service it is dependant on is the "Peer Name Resolution Protocol" so I try to start that and I get an error saying that the "service could not start due to error 0x80630801" This has happened before and I have fixed it then by using System Restore and restoring the machine to a week before when I knew it had all worked. This time though I cannot remember when I last used the Homegroup from this machine and I've installed quite a bit so I don't want to go fumbling through restore points trying to find one that works... Can anyone tell me if there is a way to reset things so that this machine is able to use the Homegroup again?

  Read the article

• What is the best way to connect 3 switches with a router?

  - by Carlos Morales

  Hello everyone, I'm trying to rebuild the network from my work and I was thinking what is the best way to connect three switches and a router. The router has 4 ports so I thought to connect 2 switches to the router (each switch connected with 2 cables to the router) and then connect the third switch to one of the others with two cables. So is like this, two cables from switch one to the router, two cables from switch two to the router and two cables from switch 3 to switch 1 or 2. So my questions are: Is it better to connect the router to each switch with a cable or the more cables you have the better? If I connect the switch 3 to switch 1 or 2 is it better to connect it with a cable or you get better performance with more cables. If I'm wrong and there is a better or more efficient way to connect them please let me know. The router is a Netgear RP114 (I'll upgrade it to a Sonicwall NSA 240), switch 1 is a Netgear GS748T, switch 2 is a Cisco Catalyst 2924-XL and switch 3 is a D-link DGS-1024D Thank you very much

  Read the article

• Disable laptop CD-ROM drive

  - by Stan

  Since I seldom use the built-in cd-rom, but usually carelessly press open door button which is on the side of laptop. Is there any way to power off cd-rom so the button won't work. Better not to open the back lid and unplug power cable.

  Read the article

• Using the link command to keep backups on another drive

  - by Xavier

  I have a folder that contains a not so large amount of space called /data/backup. I have been told that if I link that folder (/data/backup) to an even bigger folder area like /bigdata/backup for example, that I will be able to execute backups to the /data/backup folder. It will then just create a link, but the data will be seen in both folders and the latter one (/bigdata/backup) will contain the backup results but it will show on both folders. Since the /bigdata/backup has far more disk space then the backup will no longer fail because of space problems in the /data/backup one. Is this true?

  Read the article

• Delete ARP cache on Mac OS when moving from one Wifi network to the other

  - by Puneet

  I am facing wireless connectivity problems when I move from one Wifi network to the other. Here is how it happens: I am at my friends place. I connect to his Wifi. His Wifi router ip address is 192.168.0.1. Everything is fine I close my laptop, come back to my house, open my laptop and I connect to the Wifi Network at my place. Different ESSID, but the Wifi router address is the same 192.168.0.1. At this point I cant get to anything on the internet. To debug I try to see if I can ping the router (192.168.0.1), I cant. I get a no route to host. Meanwhile airport tells me Im connected to Wifi. I see the arp cache and I see a permanent entry for 192.168.0.1 ? (192.168.0.1) at 5c:d9:98:65:73:6c on en1 permanent [ethernet] This permanent bit looks problematic. I go ahead and delete the arp cache entry and all is fine with the world until I go back to my friends place where the same situation plays out. Now my question is, why the hell is this happening? If there is no way around it, can I run a script on Wifi connect/disconnect to clear out the arp cache? Im using Mac OS X $uname -a Darwin 10.8.0 Darwin Kernel Version 10.8.0: Tue Jun 7 16:33:36 PDT 2011; root:xnu-1504.15.3~1/RELEASE_I386 i386

  Read the article

• files that cannot be transfered from dvd to removable drive

  - by user23950

  what is the solution if there is always an error while transferring a file-data error:crc I tried to play the video file which cannot be transferred and it can be played from the dvd but when I try to transfer it using terra copy. I always see this crc error.

  Read the article

• XP shared folders not accessible after BIOS changed

  - by stijn

  Here's what worked for over a year: PC A runs Windows 7, PC B runs Windows XP. Both are on the same subnet behind a router. A uses user account X, but logs in to PC B using the Administrator account. PC B is a Dell Precision 470. A known problem with these is that sometimes when plugging in their power cable they somehow loses all BIOS settings. This happened yesterday. After this happens Windows won't boot, because the default BIOS setting is 'RAID ON' while there is no RAID configured. No problem though, changing the BIOS settings to 'RAID OFF' makes it boot without problems. Note that in the meantime, nothing config-related was changed on machine A. It wasn't even on. Indeed after doing this, everything is fine. Everything includes all normal operations, remote desktop from PC A to PC B, running Synergy between A and B, accessing shared folders from B to A. But accessing the shared folders on B from A does not work any more. I tried pretty much everything I found via Google (fiddling with policies/registry kes/...) but no avail. > ping -a 192.168.2.2 Pinging A [192.168.2.2] with 32 bytes of data: Reply from 192.168.2.2: bytes=32 time<1ms TTL=128 > net view \\192.168.2.2 System error 5 has occurred. Access is denied. > net use /persistent:no K: \\A\myshare /user:A\USERNAME PASSWORD > net use /persistent:no K: \\192.168.2.2\myshare /user:192.168.2.2\USERNAME PASSWORD > net use /persistent:no K: \\192.168.2.2\myshare /user:USERNAME PASSWORD System error 86 has occurred. The specified network password is not correct. A solution to this would be great: I haven't been able to do any work since yesterday ;] update after taking the hard drive out of B and putting it in another Precision 470 with almost exactly the same hardware (at first sight, only the video card differs) the shared folders work.. Putting the disk back into A, same problem remains. Why does this depend on hardware, and more important, on which hardware?

  Read the article

• "Open With" dialog appears when double clicking on a local drive in My Computer

  - by pandiya chendur

  I noticed that when i click my local drives(C:,D:) i got open with Dialog box..... I am using windows xp... Then i found autorun.txt file was added to all the drives... How to solve this? Any suggestion...

  Read the article

• Grub Error 18 - Solid State Drive

  - by clint

  I recently used Raw Copy to make an image of my 300gb Raptor Hd to a OCZ Vertex SSD 60GB. And When I pluged in the SSD to boot I get a Grub Error 18. I have tried to changed in the BIOS setting to LBA, Large, Auto, trying different combination's. Any advice. thanks, Clint

  Read the article

• SBD killing both cluster nodes when there are even small SAN network problems

  - by Wieslaw Herr

  I am having problems with stonith SBD in a openais-based cluster. Some background: The active/passive cluster has two nodes, node1 and node2. They are configured to provide an NFS service to users. To avoid problems with split-brain, they are both configured to use SBD. SBD is using two 1MB disks available to the hosts via an multipath fibre-channel network. The problems start if something happens with the SAN network. For example, today one of the brocade switches got rebooted and both nodes lost 2 out of 4 paths to each disks, which resulted in both nodes committing suicide and rebooting. This, of course, was highly undesirable because a) there were paths left b) even if the switch would be out for 10-20 seconds a reboot cycle of both nodes would take 5-10 minutes and all NFS-locks would be lost. I tried increasing the SBD timeout values (to 10sec+ values, dump attached at the end), however a "WARN: Latency: No liveness for 4 s exceeds threshold of 3 s" hints that something isn't working as I would it expect to. Here is what I would like to know: a) Is SBD working as it should killing nodes when 2 paths are available? b) If not, is the multipath.conf file attached correct? The storage controller we use is an IBM SVC (IBM 2145), should there be any specific configuration for it? (as in multipath.conf.defaults) c) How should I go about increasing the timeouts in SBD attachements: Multipath.conf and sbd dump (http://hpaste.org/69537)

  Read the article

• Setting Up My Home Network

  - by Skizz

  I currently have five PCs at home, three running WinXP and two running Ubuntu. They are set up like this: ISP ----- Modem ---- Switch ---- Ubuntu1 -- B&W Printer | |--WinXP1 | |--WinXP2 Wireless |--Colour Printer | |---------Ubuntu2 |---------WinXP3 (laptop) The Ubuntu1 machine is set up as a PDC using Samba and runs fetchmail, procmail, dovecot to get my e-mail and allow me to access the e-mail via imap so I can read the e-mail on any PC. I'd like to set up the network like this: ISP ----- Modem ---- Ubuntu1 ---- Switch ------WinXP1 | | |--WinXP2 B&W Printer Wireless |--Colour Printer | |---------Ubuntu2 |---------WinXP3 (laptop) My questions are: How to configure Ubuntu1 to act as a firewall. How to configure Ubuntu1 to provide a consistant user authentication across the network, at the moment Samba provides roaming profiles for the XP machines but the Ubuntu2 machine has it's own user lists. I'd like to have a single authentication for both XP machines and linux machines so that users added to the server list will propagate to all PCs (i.e. new users can log on using any PC without modifying any of the client PCs). How to configure a linux client (Ubuntu2 above) to access files on the server (Ubuntu1), some of which are in user specific folders, effectively sharing /home/{user} per user (read and write access) and stuff like /home/media/photos with read access for everyone and limited write access. How to configure the XP machines (if it is different from a the Samba method). How to set up e-mail filtering. I'd like to have a whitelist/blacklist system for incoming e-mails for some of the e-mail accounts (mainly, my kids' accounts) with filtered e-mails being put into quaranteen until a sysadmin either adds the sender to a blacklist or whitelist. OK, that's a lot of stuff. For now, I don't want config files*, rather, what services / applications to use and how they interact. For example, LDAP could be used for authentication but what else would be useful to make the administration of the LDAP easier. Once I have a general idea for the overall configuration, I can ask other questions about the specifics. Skizz I have looked around for information, but most answers are usually in the form of abstract config files and lists of packages to install.

  Read the article

• linux keeps disconnecting from wireless network

  - by Matteo Ceccarello

  I'm running Arch Linux on an Acer laptop and my wirless connection doesn't stay up. After a while it disconnects, and when I try to reconnect I get stuck with a "Waiting for authorization" message. I have to retry several times before getting the connection stay up for few minutes. This happens with both networkmanager and wicd. The strange thing is that the iMac that sits next to the laptop connects fine, and when I use my laptop within the university wireless network it works normally. How can I solve this problem? EDIT: I've tried to connect manually following the steps iwlist wlan0 scan wpa_supplicant -i wlan0 -c /etc/wpa_supplicant.conf dhcpcd wlan0 and it works, I can ping google. However, looking to wpa supplicant output I see that it keeps connecting and disconnecting. I'm using WPA2, and this seems to be a problem in authentication. EDIT 2: as pointed out in the answers I forgot to mention my hardware/software specifications: kernel: Linux 3.0-ARCH wireless card: # lspci | grep -i net 07:00.0 Network controller: Intel Corporation WiFi Link 5100 module used # lsmod | grep -i 80211 mac80211 216021 1 iwlagn I use a Netgear DGN1000 modem/router My dmseg output is shown here http://pastebin.com/8Tf7iage

  Read the article

• Show full URI/URL in Chrome's developer tools Network tab

  - by Lev

  When using Chrome to debug, I find it incredibly difficult to be efficient due to the fact that I don't see how I can force the "Network" tab of the developer tools to show the full request URI. It will show the full URI if you hover the link and wait a second, but this is incredibly counterproductive. All of my AJAX requests are sent to ajax.php, and handled by using query string arguments, like: ajax.php?do=profile-set ajax.php?do=game-save ... etc. Since I use AJAX extensively, my network tab is filled with "ajax.php", but I have to manually hover each and every entry to find the request I am looking for. Surely there has got to be another way!? I am constantly fed up by something new in Firefox and immediately force myself back into Chrome, but it is always the developer tools in Chrome that keep me from using it for an extended period of time. Hopefully I can find out how to do this so I can continue using Chrome as my numero uno. I've provided a screen shot to show you where I mean:

  Read the article

• What was SPX from the IPX/SPX stack ever used for?

  - by Kumba

  Been trying to learn about older networking protocols a bit, and figured that I would start with IPX/SPX. So I built two MS-DOS virtual machines in VirtualBox, and got IPX communications working (after much trial and error). The idea being to get several old DOS games to run, link up to a multiplayer match, interact with each game window, and capture the traffic using Wireshark from the host machine. From this, I got Quake, Masters of Orion 2, and MechWarrior 2 to communicate back and forth. Doom, Doom2, Duke3d, Warcraft, and several others either buggered up under the VM or just couldn't see the other VM on the IPX network. What did I discover? None of the working games used SPX. Not even Microsoft's NET DIAG used SPX. They all ran ONLY on top of IPX. I can't even find SPX examples or use-cases of SPX traffic running over IEEE 802.3 Ethernet II framing. I did find references that it was in abundant use on token ring, but that's it. Yet any IPX-aware application that I've hunted down so far usually advertises itself as "IPX/SPX", which seems to be a bit of a misnomer, since it doesn't seem to use SPX. So what was SPX used for? Any DOS applications out there that use it which will run under my VM setup? Edit: I am aware that IPX is to SPX as IP is to TCP (layer 3 to layer 4), so I expected to see an SPX layer underneath the IPX layer in Wireshark when I ran my tests.

  Read the article

• scalable yet doable small-medium office network

  - by Jared

  Hello, I'm studying up with both Microsoft and Cisco literature and I must say, my head is starting to get clustered up (pun intended). I've made a quick network diagram of a theoretical company... Company1 owns Company 2 and Company 3, which are all under separate rooms and networks, but must be able to share a few resources such as files or printers. Given the amount of info out there and best practices, I thought about posting here to get suggestions and see what would the pro's do. I can read and read all day and implement on my own, but if I dont get some outside input, how will I know if I'm doing something wrong, right? anyway, please take a look and see if this is an over-complicated network or a lackluster design for a small-medium company of about 35 people and lets say they will be double that number by end of the year... :) Using win2k3, esxi, windows xp. FCS - forefront client security, ACS - access control system, SPCWK - spiceworks, XCH - Exchange Im not allowed to post an image yet, so here's the link ---- GLIFFY IMAGE Flame suit is on just in case people get mad at me for making an "abomination". I'd really want to get the general overview properly before I dive into the more complicated things

  Read the article

• What is the peak theoretical WiFi G user density? [closed]

  - by Bigbio2002

  I've seen a few WiFi capacity planning questions, and this one is related, but hopefully different enough not to be closed. Also, this is related specifically to 802.11g, but a similar question could be made for N. In order to squeeze more WiFi users into a space, the transmit power on the APs need to be reduced and the APs squeezed closer together. My question is, how far can you practically take this before the network becomes unusable? There will come a point where the transmit power is so weak that nobody will actually be able to pick up a connection, or be constantly roaming to/from APs spaced a few feet apart as they walk around. There are also only 3 available channels to use as well, which is a factor to consider. After determining the peak AP density, then multiply by users-per-AP, which should be easier to find out. After factoring all of this in and running some back-of-the-envelope calculations, I'd like to be able to get a figure of "XX users per 10ft^2" or something. This can be considered the physical limit of WiFi, and will keep people from asking about getting 3,000 people in a ballroom conference on WiFi. Can anyone with WiFi experience chime in, or better yet, provide some calculations for a more accurate figure? Assumptions: Let's assume an ideal environment with no reflection (think of a big, square, open room, with the APs spaced out on a plane), APs are placed on the ceiling so humans won't absorb the waves, and the only interference are from the APs themselves and the devices. As for what devices specifically, that's irrelevant for the first point of the question (AP density, so only channel and transmit power should matter). User experience: Wikipedia states that Wireless G has about 22Mbps maximum effective throughput, or about 2.75MB/s. For the purpose of this question, anything below 100KB/s per user can be deemed to be a poor user experience. As for roaming, I'll assume the user is standing in the same place, so hopefully that will be a non-issue.

  Read the article

• Windows Server 2008 R2 Finding Hidden files that are causing drive to fill up

  - by Xaxum

  What is the best way to find out what files are sucking up so much space? My Windows directory lists its size as 15 GB but when I run a powershell script against it, it shows 40 GB. It seems 40 GB is about right because if I use that 40 GB and add it to the rest of my folders on C I get the 45 GB that is in use. I checked volume shadow copy and that is disabled and there are no volume shadow files listed. My page file is limited to 3 GB. How can I find out what files are taking 25 GB of space? Final Results: We ended up disabling UAC and then the Properties showed the true file size of the Windows folder, as shown in powershell script. This allowed us to drill down to the folder that had the issues... In our case it was in C:\Windows\System32\config\systemprofile\AppData\Local\VMware\VDM there were several large dump files, these were the mysterious unknown files in WinDirStat. It turns out our nessus scan is crashing a view service for a couple seconds so it creates a large dump file. So we will try this.. https://discussions.nessus.org/thread/5212

  Read the article

• Windows 7, Printer is unavailable until PC reboot

  - by Cjs

  We are having a problem that I haven't seen before and can find no answers to online. A desktop running Windows 7 is unable to print using network printers. When the user tries, no matter what printer it is, he get's the following message when using Microsoft Office applications: "Current printer is unavailable. Select another printer." When the end user uses Outlook we get the message: "Printing is not available. There are no printers installed. You can select and configure a printer in Windows Control Panel." Now here is the confusing part, if we reboot the pc it works fine for a little while and then goes back to the same old same old. The printers are working fine for every other user as well so I believe it is the user's machine. If anyone has any ideas please let me know. Edit: I'd like to add in that some people were having luck disabling snmp for the printers. Restarting the print spooler doesn't seem to do anything.

  Read the article

• Destination NAT Onto the Same Network from internal clients

  - by mivi

  I have a DSL router which acts as NAT (SNAT & DNAT). I have setup a server on internal network (10.0.0.2 at port 43201). DSL router was configured to "port forward" (or DNAT) all incoming connections to 10.0.0.2:43201. I created a virtual server for port forwarding on DSL router. I also added following iptables rules for port forwarding. iptables -t nat -A PREROUTING -p tcp -i ppp_0_1_32_1 --dport 43201 -j DNAT --to-destination 10.0.0.2:43201 iptables -I FORWARD 1 -p tcp -m state --state NEW,ESTABLISHED,RELATED -d 10.0.0.2 --dport 43201 -j ACCEPT # ppp_0_1_32_1 is routers external interface. # routers internal IP address is 10.0.0.1 and server is setup at 10.0.0.2:43201 Problem is that connections coming from external IP addresses are able to access internal server using External IP address, but internal clients (under NAT) are not able to access server using external IP address. Example: http://<external_address>:43201 is working from external clients But, internal clients are not able to access using http://<external_address>:43201 This seems to be similar to the problem described in http://www.netfilter.org/documentation/HOWTO/NAT-HOWTO-10.html (NAT HOW-TO Destination NAT Onto the Same Network). Firstly, I am not able to understand why is this a problem for internal clients? Secondly, what iptables rule will enable internal clients to access server using external IP address? Please suggest.

  Read the article

• AFP AD ACL permissions issues with external drive

  - by AlanGBaker

  Mac OS X Server 10.4.11 connected to an AD domain system serving AFP shares to Mac OS X 10.5.8. If I create a share on the the internal RAID of the server with an ACL that allows RW to all ("Domain Users"), then it works, but a share created identically on the external RAID appliance (Drobo v2) doesn't. When the share from the Drobo is mounted, it shows no sign that it has any ACLs associated with it: neither in the Finder (Get Info), nor when checked via the terminal with "ls -lae". The Drobo does show that the ACLs exist when I ssh into the server and check it there, but when the clients mount that share, they just... ...disappear. Any thoughts?

  Read the article

• How to test/debug bad network wiring?

  - by Jack Lloyd

  I recently bought a place already wired with Cat 5E (8 ports, leading to a central closet). However attempting to get link, nothing works. On closer examination, it was obvious that the ends in the closet were wired backwards (brown on pin 1, etc). The jacks that I've pulled out of the wall do look to be correctly done. However, testing with a network cable tester shows zero link between any of the jacks and any of the ports in the closet - I had expected to just see a 1/8, 2/7, ... 8/1 mismatch, but instead get nothing at all. The runs are accessible and look neat, though they take some bends that seem quite sharp and are in some cases much longer than they need to be (the person who put this in was a professional electrician but I suspect this was the first time he ran network cabling). My best guess at this point is that he either bought bad cable, or put so much tension on it that he snapped wires. Though it seems surprising/unlikely that I wouldn't get at least one active wire on one of the 8 lines. So, my question: is there anything else I should try or test before I go ripping out everything and running new cable?

  Read the article

• Windows 8, Truecrypt drive mounts but Windows cannot read its content

  - by phil

  I installed Windows 8 and when I started it, it said that it was repairing a disk. The disk was an encrypted Truecrypt disk. I couldn't mount the disk in Truecrypt after that. I tried to repair the header and it worked, now I can mount the disk but neither Windows 7 or 8 can read the content. Windows asks if it should format the disk. I have all the important files on backup, but there are some media files that I would like to get back. Any ideas?

  Read the article

• Reliable backup software for windows network/samba shares.

  - by Eli

  Hi All, I have a Win2003 server that works as a pdc for a number of XP boxes, and a couple related FreeBSD boxes. I need to back up roaming profiles, non-roaming profiles via network shares, local hard drive data, and files on the FreeBSD boxes via samba shares. I have tried Genie Backup Manager and Backup4All pro, and both have excellent features, but both also begin to fail disastrously with more than a few days use. Mostly, the errors seem to have been from the backup catalog getting out of synch with itself. Whatever it is, there is no excuse for a backup software that says it backed up files when it really didn't, or the log saying it backed up exactly the same file 10,000 times in a single run, or flat-out crashing, or any of the other myriad problems I've run into with these. Really sad for products that fill such an important need. Anyway, does anyone know of a backup software that works reliably and can do the following? Scheduled backups for multiple jobs, without a user logged in. Backup from local hard drives or network shares. Incremental backups. Thanks! Edit: Selected solution: I've added my (hopefully final) solution as an answer.

  Read the article

• VMWare Workstation can't read CD/DVD drive

  - by Chris W

  A fresh install of VMWare Workstation 7 (7.1.1 build 282343) on Windows 7 64 bit. When I try to read a CD/DVD from a guest (either to install a fresh guest or to read a CD within an existing VM I get the following error: Cannot connect virtual device ide1:0 because no corresponding device is available on the host. I've tried fiddling with the IDE channels as well as tried SCSI with no joy. What am I missing? I can run ISOs fine but I don't want to have to convert everything to an ISO when I presume that this should just work fine.

  Read the article

• Connection to Google, Yahoo, Bing, Ask, etc. compromised via all devices on my home network - How?

  - by jt0dd

  I'm a very computer savvy guy (although not very networking savvy), and I may still be wrong about this, but I think my home network may be compromised somehow. I'd like to know if it's possible for someone to have hijacked my network's connection to Google.com and other popular websites. Update: The issue seems to take effect with all popular websites. I can connect to small (non-popular) websites without issue, but Facebook, Google, Yahoo, and Bing cannot be accessed by any device on my home network. On all devices using my home network, I'm being shown http://www.google.com WARNING! Internet Explorer is currently out of date. Please update to continue. when I attempt to connect to google.com. I wouldn't be surprised by this at all if it were just the laptop. It's the fact that this is happening on all devices on my network that confuses me. Here's the screenshot from my iPhone, for reference. Can my home network be compromised? Is that even possible? How can something like this happen across all platforms on all devices in the same way? I wouldn't imagine every device / platform on the network would get the same virus. Should I assume that my network's security is totally compromised? Update: All mobile devices and laptops on my home network are experiencing the same alert when attempting to connect to google.com.

  Read the article

< Previous Page | 200 201 202 203 204 205 206 207 208 209 210 211  | Next Page >