Search Results

Search found 7085 results on 284 pages for 'termine updates'.

Page 205/284 | < Previous Page | 201 202 203 204 205 206 207 208 209 210 211 212  | Next Page >

• External hard drive not recognized

  - by sr71

  Installed Ubuntu 10.10 on a hard drive by itself (no windows). All updates are up to date. Everything`works fine except when I plug in a 320 gig Toshiba external hard drive....it is not recognized. When I plug in an 8 gig flash drive it is recognized no problem. What do I mean by "not recognized"? I mean: how do you know it was not recognized. You can check the command "cat /proc/partitions" in a terminal with and without the hdd attached. If you see some difference, it's ok. If the difference is something like "sda1" (sd+letter+number) then you have partition on it, maybe it can't be handled in Ubuntu (no filesystem on it or so). If there is only "sda" in the difference for example (sd+letter, but no number after it) then the drive itself is detected, just no partition is created on it. Also you can check out the messages of the kernel, with the "dmesg" command in the terminal. If there is no disk/partition/anything in /proc/partitions, there can be an USB level problem, you can issue command "lsusb" as it was suggested before my answer. It's really matter of what do you mean about "not recognized". @Marco Ceppi @Oli @Pitto By "not recognized" I meant that when I plug in a 8 gig flash drive an icon immediately appears on the desktop imdicating that there is a flash drive plugged in and I can click on it and view the files on the flash drive. It also shows up on the "Nautilus" default file manager. When I plug in the 320 gig Toshiba external hard drive, I get no indication on the desktop or the file manager (thus "not recogized"). When I run the command cat/proc/partitions/ I get an error message Could not open location 'file:///home/bob/cat/proc/partitions' with or without the external hard drive installed. With the dmeg command I get about 10 pages of info with no mention of disk/partition/anything in /proc/partitions. When I run lsusb command I get the following: bob@bob-desktop:~$ lsusb Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 003: ID 04b3:3003 IBM Corp. Rapid Access III Keyboard Bus 003 Device 002: ID 04b3:3004 IBM Corp. Media Access Pro Keyboard Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

  Read the article

• Planning Bulletin for JRE 7: What EBS Customers Can Do Today

  - by Steven Chan (Oracle Development)

  An initiative to certify Oracle E-Business Suite with JRE 7 desktop clients is underway.  We have tested EBS 11.5.10.2, 12.0, and 12.1 with JRE 7. We have fixes for nearly all of the compatibility issues now, and are working hard to produce the remaining fixes quickly. A. When will JRE 7 be certified with Oracle E-Business Suite? We will announce the certification of the E-Business Suite with JRE 7 once all fixes are available, verified, and documented.  Certification announcements will be distributed through My Oracle Support, My Oracle Support Community Forums, Oracle Technology Network Forums, newsletters, and user group news outlets. Oracle's Revenue Recognition rules prohibit us from discussing certification and release dates.  In addition to the standard communication channels listed above, customers are encouraged to monitor or subscribe to this blog.    B. What can customers do to prepare for the JRE 7 certification? Customers should ensure that they are on the latest available JRE 6 update. Of the compatibility issues identified so far with JRE 7, the most critical is an issue that prevents E-Business Suite Forms-based products from launching on Windows desktops that are running JRE 7.  Customers can prevent this issue today by ensuring that they have applied the latest certified patches documented for JRE 6 configurations to their EBS application tier servers: Apply Forms patch 14615390 to EBS 11i environments (Note 125767.1) Apply Forms patch 14614795 to EBS 12.0 and 12.1 environments (Note 437878.1) These patches are compatible with JRE 6 and 7, production ready, and fully-tested with the E-Business Suite.  These patches may be applied immediately to all E-Business Suite environments. All other Forms prerequisites documented in the Notes above should also be applied now. C. What else will be required by the final certified configuration? Oracle expects that all other compatibility issues will be resolved by installing a specific JRE 7 release, at minimum.  That specific release has not been finalized yet, and this is subject to change. D.  Where will the official patch requirements be documented? All patches required for ensuring full compatibility of the E-Business Suite with JRE 7 will be documented in updates to these published Notes: For EBS 11i: Deploying Sun JRE (Native Plug-in) for Windows Clients in Oracle E-Business Suite Release 11i (Note 290807.1) Upgrading Developer 6i with Oracle E-Business Suite 11i (Note 125767.1) For EBS 12 Deploying Sun JRE (Native Plug-in) for Windows Clients in Oracle E-Business Suite Release 12 (Note 393931.1) Upgrading OracleAS 10g Forms and Reports in Oracle E-Business Suite Release 12 (Note 437878.1) Disclaimer The preceding is intended to outline our general product direction.  It is intended for information purposes only, and may not be incorporated into any contract.   It is not a commitment to deliver any material, code, or functionality, and should not be relied upon in making purchasing decision.  The development, release, and timing of any features or functionality described for Oracle’s products remains at the sole discretion of Oracle.

  Read the article

• RPG Monster-Area, Spawn, Loot table Design

  - by daemonfire300

  I currently struggle with creating the database structure for my RPG. I got so far: tables: area (id) monster (id, area.id, monster.id, hp, attack, defense, name) item (id, some other values) loot (id = monster.id, item = item.id, chance) spawn (id = area.id, monster = monster.id, count) It is a browser-based game like e.g. Castle Age. The player can move from area to area. If a player enters an area the system spawns, based on the area.id and using the spawn table data, new monsters into the monster table. If a player kills a monster, the system picks the monster.id looks up the items via the the loot table and adds those items to the player's inventory. First, is this smart? Second, I need some kind of "monster_instance"-table and "area_instance"-table, since each player enters his very own "area" and does damage to his very own "monsters". Another approach would be adding the / a player.id to the monster table, so each monster spawned, has it's own "player", but I still need to assign them to an area, and I think this would overload the monster table if I put in the player.id and the area.id into the monster table. What are your thoughts? Temporary Solution monster (id, attackDamage, defense, hp, exp, etc.) monster_instance (id, player.id, area_instance.id, hp, attackDamage, defense, monster.id, etc.) area (id, name, area.id access, restriction) area_instance (id, area.id, last_visited) spawn (id, area.id, monster.id) loot (id, monster.id, chance, amount, ?area.id?) An example system-flow would be: Player enters area 1: system creates area_instance of type area.id = 1 and sets player.location to area.id = 1 If Player wants to battle monsters in the current area: system fetches all spawn entries matching area.id == player.location and creates a new monster_instance for each spawn by fetching the according monster-base data from table monster. If a monster is fetched more than once it may be cached. If Player actually attacks a monster: system updates the according monster_instance, if monster dies the instance if removed after creating the loot If Player leaves the area: area_instance.last_visited is set to NOW(), if player doesn't return to data area within a certain amount of time area_instance including all its monster_instances are deleted.

  Read the article

• Misaligned Display on Resume

  - by Shaun Killingbeck

  I have an odd issue with my laptop display when resuming from suspend. When I have an additional monitor connected there is no issue. However without an additional monitor connected, after resuming only the left 10% of the laptop screen (just enough to show the Unity Launcher and a bit more) is visibly working, although strangely in a screenshot this same 10% is shown on the right hand side of the screenshot: I ran xrandr --verbose before and after resume, and the only difference (using diff) was: 2c2 < LVDS connected 1366x768+0+0 (0x98) normal (normal left inverted right x axis y axis) 344mm x 194mm --- > LVDS connected 1366x768+1280+0 (0x98) normal (normal left inverted right x axis y axis) 344mm x 194mm This seems to suggest the screen position has been shifted by 1280 horizontally, the width of the second monitor I use. Indeed, running the command xrandr --output LVDS --pos 0x0 does bring the screen back to normal. However, I don't want to have to run this command every time, I'd prefer to cure the source of the problem than just correct the symptoms. Any ideas on how to get Ubuntu to keep the display configuration settings from before suspend when it resumes? or why it changes at all? Heres some technical details that might be pertinent: HP Pavilion DV6 Laptop Ubuntu 13.04 AMD Radeon HD 6400M Series AMD Radeon HD 6520G Using proprietary flgrx-updates driver and amdcccle (Catalyst Control Center) (Unfortunately the open source driver causes my laptop to run even hotter than it already does, otherwise I'd use that) The contents of Xorg.conf: Section "ServerLayout" Identifier "amdcccle Layout" Screen 0 "amdcccle-Screen[0]-0" 0 0 EndSection Section "Module" Load "glx" EndSection Section "Monitor" Identifier "0-LVDS" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" Option "PreferredMode" "1280x768" Option "TargetRefresh" "60" Option "Position" "0 0" Option "Rotate" "normal" Option "Disable" "false" EndSection Section "Monitor" Identifier "0-CRT1" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" Option "PreferredMode" "1280x768" Option "TargetRefresh" "60" Option "Position" "0 0" Option "Rotate" "normal" Option "Disable" "false" EndSection Section "Monitor" Identifier "1-LVDS" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" Option "TargetRefresh" "60" Option "Position" "1280 0" Option "Rotate" "normal" Option "Disable" "false" Option "PreferredMode" "1366x768" EndSection Section "Monitor" Identifier "1-CRT1" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" Option "TargetRefresh" "60" Option "Position" "0 0" Option "Rotate" "normal" Option "Disable" "false" Option "PreferredMode" "1280x1024" EndSection Section "Device" Identifier "amdcccle-Device[0]-0" Driver "fglrx" Option "Monitor-LVDS" "1-LVDS" Option "Monitor-CRT1" "1-CRT1" BusID "PCI:0:1:0" EndSection Section "Device" Identifier "amdcccle-Device[0]-1" Driver "fglrx" Option "Monitor-LVDS" "1-LVDS" BusID "PCI:0:1:0" Screen 1 EndSection Section "Screen" Identifier "Default Screen" DefaultDepth 24 EndSection Section "Screen" Identifier "amdcccle-Screen[0]-0" Device "amdcccle-Device[0]-0" DefaultDepth 24 SubSection "Display" Viewport 0 0 Virtual 2646 2646 Depth 24 EndSubSection EndSection Section "Screen" Identifier "amdcccle-Screen[0]-1" Device "amdcccle-Device[0]-1" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection

  Read the article

• Quick run through of the WP7 Developer Tools January 2011

  - by mbcrump

  In case you haven’t heard the latest WP7 Developers Tool update was released yesterday and contains a few goodies. First you need to go and grab the bits here. You can install them in any order, but I installed the WindowsPhoneDeveloperResources_en-US_Patch1.msp first. Then the VS10-KB2486994-x86.exe. They install silently. In other words, you would need to check Programs and Features and look in Installed Updates to see if they installed successfully. Like the screenshot below: Once you get them installed you can try out a few new features. Like Copy and Paste. Just fire up your application and put a TextBox on it and Select the Text and you will have the option highlighted in red above the text. Once you select it you will have the option to paste it. (see red rectangle below). Another feature is the Windows Phone Capability Detection Tool – This tool detects the phone capabilities used by your application. This will prevent you from submitting an app to the marketplace that says it uses x feature but really does not. How do you use it? Well navigate out to either directory: %ProgramFiles%\Microsoft SDKs\Windows Phone\v7.0\Tools\CapDetect %ProgramFiles (x86)%\Microsoft SDKs\Windows Phone\v7.0\Tools\CapDetect and run the following command: CapabilityDetection.exe Rules.xml YOURWP7XAPFILEOUTPUTDIRECTORY So, in my example you will see my app only requires the ID_CAP_MICROPHONE. Let’s see what the WmAppManifest.xml says in our WP7 Project: Whoa! That’s a lot of extra stuff we don’t need. We can delete unused capabilities safely now. Some of the other fixes are: (Copied straight from Microsoft) Fixes a text selection bug in pivot and panorama controls. In applications that have pivot or panorama controls that contain text boxes, users can unintentionally change panes when trying to copy text. To prevent this problem, open your application, recompile it, and then resubmit it to the Windows Phone Marketplace. Windows Phone Connect Tool – Allows you to connect your phone to a PC when Zune® software is not running and debug applications that use media APIs. For more information, see How to: Use the Connect Tool. Updated Bing Maps Silverlight Control – Includes improvements to gesture performance when using Bing™ Maps Silverlight® Control. Windows Phone Developer Tools Fix allowing deployment of XAP files over 64 MB in size to physical phone devices for testing and debugging. That’s pretty much it. Thanks again for reading my blog!  Subscribe to my feed CodeProject

  Read the article

• Partial Submit vs. Auto Submit

  - by Frank Nimphius

  Partial Submit ADF Faces adds the concept of partial form submit to JavaServer Faces 1.2 and beyond. A partial submit actually is a form submit that does not require a page refresh and only updates components in the view that are referenced from the command component PartialTriggers property. Another option for refreshing a component in response to a partial submit is call AdfContext.getCurrentInstance.addPartialTarget(component_instance_handle_goes_here)in a managed bean. If a form contains required fields that the user left empty invoking the partial submit, then errors are shown for each of the field as the full form gets submitted. Autosubmit An input component that has its autosubmit property set to true also performs a partial submit of the form. However, this time it doesn't submit the entire form but only the component that triggers the submit plus components referenced it in their PartialTriggers property. For example, consider a form that has three input fields inpA, inpB and inpC with autosubmit=true set on inpA and required=true set on inpB and inpC. use case 1: Running the view, entering data into inpA and then tabbing out of the field will submit the content for inpA but not for inpB and inpC. Further more, none of the required field settings on inpB and inpC causes an error. use case 2: You change the configuration of inpC and set its PartialTriggers property to point to the ID of component inpA. When rerunning the sample, entering a value into inpA and tabbing out of the field will now submit the inpA and inpC fields and thus show an error for the missing required value on inpC. Internally, using autosubmit=true on an input component sets the event root to just this field, which good to have in case of dependent field validation or behavior. The event root can extended to include other components by using the Partial Triggers property on these components to point to the input field that has autosubmit=true defined. PartialSubmit vs. AutoSubmit Partial submit set on a command component submits the whole form and leaves it to the developer to decide which UI component is refreshed in response. Client side required field validation (as well as the server side equivalent) is not disabled by executed in this scenario. Setting immediate=true on the command item to skip validation doesn't help as it would also skip the model update. Auto submit is a functionality on the input components and also performs a partial form submit. However, in addition an event root is defined that narrows the scope for the submitted data and thus the components that are validated on the request. To read more about this topic, see: http://docs.oracle.com/cd/E23943_01/web.1111/b31973/af_lifecycle.htm#CIAHCFJF

  Read the article

• No client internet access when setting up these iptables rules

  - by Siriss

  I have read many other posts but cannot figure this out. eth0 is my external connected to a Comcast modem. The server has internet access with no issues. eth1 is internal and running DHCP for the clients. I have DHCP working just fine, all my clients can get an IP and ping the server but they cannot access the internet. I am using ISC-DHCP-SERVER and have set /etc/default/isc-dhcp-server to INTERFACE="eht1" Here is my dhcpd.conf file located in /etc/dhcp/dhcpd.conf ddns-update-style interim; ignore client-updates; subnet 10.0.10.0 netmask 255.255.255.0 { range 10.0.10.10 10.0.10.200; option routers 10.0.10.2; option subnet-mask 255.255.255.0; option domain-name-servers 208.67.222.222, 208.67.220.220; #OpenDNS # option domain-name "example.com"; default-lease-time 21600; max-lease-time 43200; authoritative; } I have made the *net.ipv4.ip_forward=1* change in /etc/sysctl.conf here is my interfaces file: auto lo iface lo inet loopback auto eth0 iface eth0 inet dhcp iface eth1 inet static address 10.0.10.2 netmask 255.255.255.0 network 10.0.10.0 auto eth1 And finally- here is my iptables.conf file: # Firewall configuration written by system-config-firewall # Manual customization of this file is not recommended. *nat :PREROUTING ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :POSTROUTING ACCEPT [0:0] -A POSTROUTING -s 10.0.10.0/24 -o eth0 -j MASQUERADE #-A PREROUTING -i eth0 -p tcp --dport 59668 -j DNAT --to-destination 10.0.10.2:59668 COMMIT *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT -A INPUT -p icmp -j ACCEPT -A INPUT -i lo -j ACCEPT -A INPUT -i eth1 -j ACCEPT -A INPUT -m state --state NEW -m tcp -p tcp --dport 22 -j ACCEPT -A INPUT -m state --state NEW -m tcp -p tcp --dport 80 -j ACCEPT -A INPUT -m state --state NEW -m tcp -p tcp --dport 443 -j ACCEPT -A INPUT -m state --state NEW -m tcp -p tcp --dport 53 -j ACCEPT -A INPUT -m state --state NEW -m udp -p udp --dport 53 -j ACCEPT -A FORWARD -s 10.0.10.0/24 -o eth0 -j ACCEPT -A FORWARD -d 10.0.10.0/24 -m state --state ESTABLISHED,RELATED -i eth0 -j ACCEPT -A FORWARD -p icmp -j ACCEPT -A FORWARD -i lo -j ACCEPT -A FORWARD -i eth1 -j ACCEPT #-A FORWARD -i eth0 -m state --state NEW -m tcp -p tcp -d 10.0.10.2 --dport 59668 -j ACCEPT -A INPUT -j REJECT --reject-with icmp-host-prohibited -A FORWARD -j REJECT --reject-with icmp-host-prohibited COMMIT I am completely stuck. I cannot figure out why the clients cannot access the internet. Am I missing a service? Is a service not running? Any help would be greatly appreciated. I tried to be as thorough as possible but please let me know if I have missed something. Thank you!

  Read the article

• Various issues linked to my CD drive, when it has a disc in it

  - by Voyagerfan5761

  When I go to the Desktop and click on a media icon (for my flash drive, a CD, whatever it is), the following problems occur, in this approximate sequence: Nautilus will close if it's open. the desktop icons disappear my Window List shows a button that says "Starting File Manager" the icons reappear the button in Window List disappears Because of this problem, I can no longer drag and drop media, nor can I right-click to perform actions such as "Eject" and "Safely Remove Drive". The same symptoms occur if I click a media icon (that is also present on the desktop) in Nautilus' Computer view, though notably not if I click in the places list on the left. I have confirmed that this problem happens only if there is a CD in the drive (Matshita UJDA360). Also, inserting a disc into the CD drive appears to kill all running programs and restart Nautilus (or X; I'm not sure). Applications like Brasero and Rhythmbox will not start while there is a disc in the drive. Removing the disc doesn't result in the list of media updating; it must be forced to update by clicking on one of the desktop icons and going through one of the above-described cycles. It doesn't seem to matter what type of disc is in the drive. This has happened with CD-RWs I burned years ago using Roxio on Windows XP, the Ubuntu disc I installed from (burned with InfraRecorder Portable under Windows XP), and the retail game disc for Star Trek Armada II. The first indication of a problem was Brasero dying when I tried to insert a disc for erasure and rewriting. Since then, I've drafted several different questions on various issues, finally combining them into this one when I realized that having a CD in the drive was the common link. Could this be a simple driver issue? If Ubuntu is dynamically detecting my hardware on boot, can I specify drivers for devices that I know will be a problem if the default files are used? I'm beginning to think that my laptop, an old Dell Inspiron 2650, is just too old or proprietary-driver-hungry (or something, maybe RAM-starved) for Ubuntu and Windows XP to play nicely alongside each other. Or maybe I just need to carefully take my wall-wart machine to a coffee shop for an afternoon so I can download updates and such from the Internet, as I lack a home connection.

  Read the article

• TouchDevelop: The Fast Path to Windows 8 and Phone Apps

  - by Clint Edmonson

  Are you looking for a little extra cash for the upcoming holidays? Then you might be interested in creating some cool apps to sell in the Windows Store. Or maybe you’re simply curious and want to try your hand at developing for Windows 8 and Windows Phone. In either case, the newly released TouchDevelop Web App is for you. TouchDevelop Web App is a development environment to create apps on your tablet or smartphone, without requiring a separate PC. Scripts written by using TouchDevelop can access data, media, and sensors on the phone, tablet, and PC. The script can interact with cloud services, including storage, computing, and social networks. TouchDevelop lets you quickly create fun games and useful tools, turning your scripts into true Windows Phone and Windows 8 apps. A year ago, Microsoft Research released TouchDevelop for Windows Phone, which is being used by enthusiasts, students, and researchers to program their phones in fun, inventive, and interesting ways. These scripts are available at TouchDevelop for anyone to download and use. Ever since we released TouchDevelop, we’ve been eyeing the tablet form factor and working on a version for the browser. Now, with the release of TouchDevelop Web App, the wait is over: the tablet version is ready, so go play around with it. All TouchDevelop scripts that are developed on the smartphone can be downloaded to the tablet and run (if hardware allows). Any script that is developed on the tablet can also be accessed on the phone. And scripts can be converted to Windows Phone or Windows 8 apps and submitted to the Windows Phone Store or Windows Store, respectively. TouchDevelop Web App’s editor and programming language have been designed for tablet devices with touchscreens, but you can also use a keyboard and a mouse. So grab your web-enabled device and give the TouchDevelop Web App a try. It’s fun and easy, and could even put a little cash in your holiday-depleted wallet. Or at least give you bragging rights at family get-togethers. Are you interested in further tips on Windows 8 development?  Sign up for the 30 to launch program which will help you build a Windows Store application in 30 days.  You will receive a tip per day for 30 days, along with potential free design consultations and technical support from a Windows 8 expert. As always, stay tuned to my twitter feed for Windows 8, Windows Azure and other Microsoft announcements, updates, and links: @clinted

  Read the article

• SAPPHIRE HD 7770 no audio on HDMI TV display

  - by zeroconf

  I have SAPPHIRE HD 7770 and cannot get work audio over HDMI. http://www.sapphiretech.com/presentation/product/?cid=1&gid=3&sgid=1159&lid=1&pid=1452&leg=0 I use Ubuntu 12.04 LTS 64-bit version with all current updates. I tried at /etc/default/grub: GRUB_CMDLINE_LINUX_DEFAULT="quiet splash radeon.audio=1" ... it didn't help. It's probably I use proprietary driver -this seems to be open source driver. I use the driver, what jockey-gtk (additional drivers) offered me: ATI/AMD PROPRIETARY FGLRX GRAPHICS DRIVER <---- I installed that one ATI/AMD PROPRIETARY FGLRX GRAPHICS DRIVER (post-release update) So - I installed the first one, because installing second version failed. Everything went fine but no sound at TV display by HDMI. Even Gnome sound mixer doesn't show HDMI choice. Using 32" Samsung B530 LCD TV - http://www.lcdbesttv.com/2010/02/samsung-b530-series-lcd-tv/ I have Asus P8Z77-M motherboard - http://www.asus.com/Motherboards/Intel_Socket_1155/P8Z77M/ - there is also HDMI integrated. When I put HDMI cord to that plug, then even Gnome sound mixer showed HDMI audio but it didn't work. I have set from BIOS, that I use that SAPPHIRE HD 7770 from PCIe. My lspci output: 00:00.0 Host bridge: Intel Corporation Ivy Bridge DRAM Controller (rev 09) 00:01.0 PCI bridge: Intel Corporation Ivy Bridge PCI Express Root Port (rev 09) 00:02.0 Display controller: Intel Corporation Ivy Bridge Graphics Controller (rev 09) 00:14.0 USB controller: Intel Corporation Panther Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) 00:1c.5 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 6 (rev c4) 00:1c.6 PCI bridge: Intel Corporation 82801 PCI Bridge (rev c4) 00:1d.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Panther Point 6 port SATA Controller [AHCI mode] (rev 04) 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) 01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI Device 683d 01:00.1 Audio device: Advanced Micro Devices [AMD] nee ATI Device aab0 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 09) 04:00.0 PCI bridge: ASMedia Technology Inc. ASM1083/1085 PCIe to PCI Bridge (rev 03)

  Read the article

• Another question about handling game states

  - by Eva

  I'm making a game designed with the entity-component paradigm that uses systems to communicate between components as explained here. I've reached the point in my development that I need to add game states (such as paused, playing, level start, round start, game over, etc.), but I'm not sure how to do it with my framework. I've looked at this code example on game states which everyone seems to reference, but I don't think it fits with my framework. It seems to have each state handling its own drawing and updating. My framework has a SystemManager that handles all the updating using systems. For example, here's my RenderingSystem class: public class RenderingSystem extends GameSystem { private GameView gameView_; /** * Constructor * Creates a new RenderingSystem. * @param gameManager The game manager. Used to get the game components. */ public RenderingSystem(GameManager gameManager) { super(gameManager); } /** * Method: registerGameView * Registers gameView into the RenderingSystem. * @param gameView The game view registered. */ public void registerGameView(GameView gameView) { gameView_ = gameView; } /** * Method: triggerRender * Adds a repaint call to the event queue for the dirty rectangle. */ public void triggerRender() { Rectangle dirtyRect = new Rectangle(); for (GameObject object : getRenderableObjects()) { GraphicsComponent graphicsComponent = object.getComponent(GraphicsComponent.class); dirtyRect.add(graphicsComponent.getDirtyRect()); } gameView_.repaint(dirtyRect); } /** * Method: renderGameView * Renders the game objects onto the game view. * @param g The graphics object that draws the game objects. */ public void renderGameView(Graphics g) { for (GameObject object : getRenderableObjects()) { GraphicsComponent graphicsComponent = object.getComponent(GraphicsComponent.class); if (!graphicsComponent.isVisible()) continue; GraphicsComponent.Shape shape = graphicsComponent.getShape(); BoundsComponent boundsComponent = object.getComponent(BoundsComponent.class); Rectangle bounds = boundsComponent.getBounds(); g.setColor(graphicsComponent.getColor()); if (shape == GraphicsComponent.Shape.RECTANGULAR) { g.fill3DRect(bounds.x, bounds.y, bounds.width, bounds.height, true); } else if (shape == GraphicsComponent.Shape.CIRCULAR) { g.fillOval(bounds.x, bounds.y, bounds.width, bounds.height); } } } /** * Method: getRenderableObjects * @return The renderable game objects. */ private HashSet<GameObject> getRenderableObjects() { return gameManager.getGameObjectManager().getRelevantObjects( getClass()); } } Also all the updating in my game is event-driven. I don't have a loop like theirs that simply updates everything at the same time. I like my framework because it makes it easy to add new GameObjects, but doesn't have the problems some component-based designs encounter when communicating between components. I would hate to chuck it just to get pause to work. Is there a way I can add game states to my game without removing the entity-component design? Does the game state example actually fit my framework, and I'm just missing something?

  Read the article

• The Nine Cs of Customer Engagement

  - by Michael Snow

  Avoid Social Media Fatigue - Learn the 9 C's of Customer Engagement inside the Click Here The order you must follow to make the colored link appear in browsers. If not the default window link will appear 1. Select the word you want to use for the link 2. Select the desired color, Red, Black, etc 3. Select bold if necessary ___________________________________________________________________________________________________________________ Templates use two sizes of fonts and the sans-serif font tag for the email. All Fonts should be (Arial, Helvetica, sans-serif) tags Normal size reading body fonts should be set to the size of 2. Small font sizes should be set to 1 !!!!!!!DO NOT USE ANY OTHER SIZE FONT FOR THE EMAILS!!!!!!!! ___________________________________________________________________________________________________________________ -- Have We Hit a Social-Media Plateau? In recent years, social media has evolved from a cool but unproven medium to become the foundation of pragmatic social business and a driver of business value. Yet, time is running out for businesses to make the most out of this channel. This isn’t a warning. It’s a fact. Join leading industry analyst R “Ray” Wang as he explains how to apply the nine Cs of engagement to strengthen customer relationships. Learn: How to overcome social-media fatigue and make the most of the medium Why engagement is the most critical factor in the age of overexposure The nine pillars of successful customer engagement Register for the eighth Webcast in the Social Business Thought Leaders series today. Register Now Thurs., Sept. 20, 2012 10 a.m. PT / 1 p.m. ET Presented by: R “Ray” Wang Principal Analyst and CEO, Constellation Research Christian Finn Senior Director, Product Management Oracle Copyright © 2012, Oracle and/or its affiliates. All rights reserved. Contact Us | Legal Notices and Terms of Use | Privacy Statement SEV100103386 Oracle Corporation - Worldwide Headquarters, 500 Oracle Parkway, OPL - E-mail Services, Redwood Shores, CA 94065, United States Your privacy is important to us. You can login to your account to update your e-mail subscriptions or you can opt-out of all Oracle Marketing e-mails at any time.Please note that opting-out of Marketing communications does not affect your receipt of important business communications related to your current relationship with Oracle such as Security Updates, Event Registration notices, Account Management and Support/Service communications.

  Read the article

• iwlwifi on lenovo z570 disabled by hardware switch

  - by Kevin Gallagher

  It was working fine with windows 7. The hardware switch is not disabled. I've toggled it back and forth dozens of times. The wifi light never turns on and it always lists as hardware disabled. I have the latest updates installed. I've been searching for solutions, but none of them seem to work for me. I've tried removing acer-wmi. I've tried setting 11n_disable=1. I've tried resetting the bios. I've tried using rfkill to unblock (only removes soft block). I've rebooted dozens of times. The wifi light turns off as soon as grub loads. Edit: I have a usb edimax wireless nic. It shows hardware disabled as well (although rfkill lists as unblocked). If I unload iwlwifi the usb nic works fine. uname -a `Linux xxx-Ideapad-Z570 3.2.0-55-generic #85-Ubuntu SMP Wed Oct 2 12:29:27 UTC 2013 x86_64 x86_64 x86_64 GNU/Linu`x rfkill list 19: phy18: Wireless LAN Soft blocked: no Hard blocked: yes dmesg [43463.022996] Intel(R) Wireless WiFi Link AGN driver for Linux, in-tree: [43463.023002] Copyright(c) 2003-2011 Intel Corporation [43463.023107] iwlwifi 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [43463.023190] iwlwifi 0000:03:00.0: setting latency timer to 64 [43463.023253] iwlwifi 0000:03:00.0: pci_resource_len = 0x00002000 [43463.023257] iwlwifi 0000:03:00.0: pci_resource_base = ffffc900057c8000 [43463.023261] iwlwifi 0000:03:00.0: HW Revision ID = 0x0 [43463.023797] iwlwifi 0000:03:00.0: irq 43 for MSI/MSI-X [43463.024013] iwlwifi 0000:03:00.0: Detected Intel(R) Centrino(R) Wireless-N 1000 BGN, REV=0x6C [43463.024250] iwlwifi 0000:03:00.0: L1 Enabled; Disabling L0S [43463.045496] iwlwifi 0000:03:00.0: device EEPROM VER=0x15d, CALIB=0x6 [43463.045501] iwlwifi 0000:03:00.0: Device SKU: 0X50 [43463.045504] iwlwifi 0000:03:00.0: Valid Tx ant: 0X1, Valid Rx ant: 0X3 [43463.045542] iwlwifi 0000:03:00.0: Tunable channels: 13 802.11bg, 0 802.11a channels [43463.045744] iwlwifi 0000:03:00.0: RF_KILL bit toggled to disable radio. [43463.047652] iwlwifi 0000:03:00.0: loaded firmware version 39.31.5.1 build 35138 [43463.047823] Registered led device: phy18-led [43463.047895] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain [43463.048037] ieee80211 phy18: Selected rate control algorithm 'iwl-agn-rs' [43463.055533] ADDRCONF(NETDEV_UP): wlan0: link is not ready nm-tool State: connected (global) - Device: wlan0 ---------------------------------------------------------------- Type: 802.11 WiFi Driver: iwlwifi State: unavailable Default: no HW Address: 74:E5:0B:4A:9F:C2 Capabilities: Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points lshw -C network *-network DISABLED description: Wireless interface product: Centrino Wireless-N 1000 [Condor Peak] vendor: Intel Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 00 serial: 74:e5:0b:4a:9f:c2 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-55-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bg resources: irq:43 memory:f1500000-f1501fff lspci 03:00.0 Network controller: Intel Corporation Centrino Wireless-N 1000 [Condor Peak]

  Read the article

• Upgrading 10.04LTS -> 10.10 using custom sources

  - by Boatzart

  I'm trying to upgrade to 10.10 from 10.04 LTS using a custom sources.list file that points to an unofficial mirror*. The mirror does have maverick, but I get the following output when upgrading: boatzart@somecomputer: > sudo do-release-upgrade Checking for a new ubuntu release Done Upgrade tool signature Done Upgrade tool Done downloading extracting 'maverick.tar.gz' authenticate 'maverick.tar.gz' against 'maverick.tar.gz.gpg' tar: Removing leading `/' from member names Reading cache Checking package manager Reading package lists... Done Building dependency tree Reading state information... Done Building data structures... Done Reading package lists... Done Building dependency tree Reading state information... Done Building data structures... Done Updating repository information WARNING: Failed to read mirror file No valid mirror found While scanning your repository information no mirror entry for the upgrade was found. This can happen if you run a internal mirror or if the mirror information is out of date. Do you want to rewrite your 'sources.list' file anyway? If you choose 'Yes' here it will update all 'lucid' to 'maverick' entries. If you select 'No' the upgrade will cancel. Continue [yN] y WARNING: Failed to read mirror file 96% [Working] Checking package manager Reading package lists... Done Building dependency tree Reading state information... Done Building data structures... Done Calculating the changes Calculating the changes Could not calculate the upgrade An unresolvable problem occurred while calculating the upgrade: The package 'update-manager-kde' is marked for removal but it is in the removal blacklist. This can be caused by: * Upgrading to a pre-release version of Ubuntu * Running the current pre-release version of Ubuntu * Unofficial software packages not provided by Ubuntu If none of this applies, then please report this bug against the 'update-manager' package and include the files in /var/log/dist-upgrade/ in the bug report. Restoring original system state Aborting Reading package lists... Done Building dependency tree Reading state information... Done Building data structures... Done Here is the relevant section from /var/log/dist-upgrade/main.log: 2010-11-18 14:05:52,117 DEBUG The package 'update-manager-kde' is marked for removal but it's in the removal blacklist 2010-11-18 14:05:52,136 ERROR Dist-upgrade failed: 'The package 'update-manager-kde' is marked for removal but it is in the removal blacklist.' 2010-11-18 14:05:52,136 DEBUG abort called *I'm located inside of USC, and for some crazy reason any sustained downloads to anywhere outside of the University are throttled down to 5kbps inside of my lab. Because of this I need to use the following sources.list: deb http://mirrors.usc.edu/pub/linux/distributions/ubuntu/ lucid main restricted universe multiverse deb http://mirrors.usc.edu/pub/linux/distributions/ubuntu/ lucid-updates main restricted universe multiverse deb http://mirrors.usc.edu/pub/linux/distributions/ubuntu/ lucid-backports main restricted universe multiverse deb http://mirrors.usc.edu/pub/linux/distributions/ubuntu/ lucid-security main restricted universe multiverse I've tried adding four more entries to the sources.list with s/lucid/maverick/ but that didn't help. Does anyone know how to fix this? Thanks!

  Read the article

• Application Integration Future &ndash; BizTalk Server &amp; Windows Azure (TechEd 2012)

  - by SURESH GIRIRAJAN

  I am really excited to see lot of new news around BizTalk in TechEd 2012. I was recently watching the session presented by Sriram and Rajesh on “Application Integration Futures: The Road Map and What's Next on Windows Azure”. It was great session and lot of interesting stuff about the feature updates for BizTalk and Azure integration. I have highlighted them below, definitely customers who haven’t started using Microsoft BizTalk ESB Toolkit should start using them which is going to be part of the core BizTalk product in future release, which is cool… BizTalk Server feature enhancements Manageability: ESB Tool Kit is going to be part of the core BizTalk product and Setup. Visualize BizTalk artifact dependencies in BizTalk administration console. HIS administration using configuration files. Performance: Improvements in ordered send port scenarios Improved performance in dynamic send ports and ESB, also to configure BizTalk host handler for dynamic send ports. Right now it runs under default host, which does not enable to scale. MLLP adapter enhancements and DB2 client transaction load balancing / client bulk insert. Platform Support: Visual Studio 2012, Windows 8 Server, SQL Server 2012, Office 15 and System Center 2012. B2B enhancements to support latest industry standards natively. Connectivity Improvements: Consume REST service directly in BizTalk SharePoint integration made easier. Improvements to SMTP adapter, to add macros for sending same email with different content to different parties. Connectivity to Azure Service Bus relay, queues and topics. DB2 client connectivity to SQL Server and SQL Server connectivity to Informix. CICS Http client connectivity to Windows. Azure: Use Azure as IaaS/PaaS for BizTalk environment. Use Azure to provision BizTalk environment for test environment / development. Later move to On-premises or build a Hybrid cloud approach. Eliminate HW procurement for BizTalk environment for testing / demos / development etc. Enable to create BizTalk farm easily and remove/add more servers as needed. EAI Service: EAI Bridge Protocol transformation Message Transformation Running custom code Message Enrichment Hybrid Connectivity LOB Applications On-premises Application On-premises Connectivity to Applications in the cloud Queues/ Topics Ftp Devices Web Services Bridge can be customized based on the service needs to provide different capabilities needed as part of the bridge. Look at the sample for EDI bridge for EDI service sample. Also with Tracking enabled through the portal. http://msdn.microsoft.com/en-us/library/windowsazure/hh674490 Adapters: Service Bus Messaging adapter - New adapter added. WebHttp adapter - For REST services. NetTcpRelay adapter - New adapter added. I will start posting more and once I start playing with this…

  Read the article

• The Use-Case Driven Approach to Change Management

  - by Lauren Clark

  In the third entry of the series on OUM and PMI’s Pulse of the Profession, we took a look at the continued importance of change management and risk management. The topic of change management and OUM’s use-case driven approach has come up in few recent conversations. So I thought I would jot down a few thoughts on how the use-case driven approach aids a project team in managing the project’s scope. The use-case model is one of several tools in OUM that is used to establish and manage the project's scope.  Because a use-case model can be understood by both business and IT project team members, it can serve as a bridge for ongoing collaboration as well as a visual diagram that encapsulates all agreed-upon functionality. This makes it a vital artifact in identifying changes to the project’s scope. Here are some of the primary benefits of using the use-case model as part of the effort for establishing and managing project scope: The use-case model quickly communicates scope in a straightforward manner. All project stakeholders can have a common foundation for the decisions regarding architecture and design and how they relate to the project's objectives. Once agreed upon, the model can be put under change control and any updates to the model can then be quickly identified as potentially affecting the project’s scope.  Changes requested or discovered later in the project can be analyzed objectively for their impact on project's budget, resources and schedule. A modular foundation for the design of the software solution can be established in Elaboration.  This permits work to be divided up effectively and executed in so that the most important and riskiest use-cases can be tackled early in the project. The use-case model helps the team make informed decisions about implementation priorities, which allows effective allocation of limited project resources.  This is very helpful in not only managing scope, but in doing iterative and incremental planning which relies heavily on the ability to identify project priorities. Bottom line is that the use-case model gives the project team solid understanding of scope early in the project.  Combine this understanding with effective project management and communication and you have an effective tool for reducing the risk of overruns in budget and/or time due to out of control scope changes. Now that you’ve had a chance to read these thoughts on the use-case model and project scope, please let me know your feedback based on your experience.

  Read the article

• OpenWorld in Small Bites

  - by Kathryn Perry

  Fifty thousand attendees -- that's bigger than the cities some of us live in. Monday morning it took 20 minutes to get from Hall D in Moscone North to a conference room in Moscone South -- the crowds were crushing! A great start to a great week! Larry is as big a name as ever on the program schedule and on the Moscone stage. People were packed in Hall D and clustered around every big screen TV. He stayed on script as he laid out Oracle's SaaS, PaaS, and IaaS strategies. Every seat in Chris Leone's Fusion Apps Cloud Overview was filled on Monday morning. Oracle employees who wanted to get in were turned away. And the same thing happened in the repeat session on Wednesday. Our newest suite of apps is hot! Speaking of hot, the weather was made to order. Then it turned very San Francisco-like on Wednesday afternoon. Downright cold for those who trusted SF temps to hold in the 80's. Who did you follow on Twitter during the conference? So many voices, opinions, and convos! Great combo of social media and sharp minds. Be sure to follow @larryellison, @stevenrmiranda, and @Oracle for updates and MyPOVs. Keywords for the Apps customers at the conference were cloud, mobile, and social. Every day, every session, every speaker. Wednesday afternoon, 4 pm at the Four Seasons hotel. A large roomful of analysts and influencers firing questions at a panel of eight Fusion customers. Steve Miranda moderating. Good energy and a great exchange of information and confidence. Word on the street is that OpenWorld has outgrown San Francisco -- but moving it seems unthinkable. The city isn't just a backdrop for an industry conference - it's a headliner right up there with Larry Ellison and Pearl Jam. As you can imagine, electrical outlets were in high demand at every venue. The most popular hotels and bars near Moscone designed their interiors around accessible electrical power strips. People are plenty willing to buy a drink while they grab a charge. Wednesday afternoon, 4 pm at the Four Seasons hotel. A large roomful of analysts and influencers firing questions at a panel of eight Fusion customers. Steve Miranda moderating. Good energy and a great exchange of information and confidence. Treasure Island in the dark. Eddy Vedder has an amazing voice! And Kings of Leon over delivered on people's expectations. It was cold. It was windy. It was very fun. One analyst said it's the best customer appreciation party in the industry. 

  Read the article

• Java EE 8 update

  - by delabassee

  Planning for Java EE 8 is now well underway. As you know, a few weeks ago, we conducted a three part Java EE 8 Community Survey (you can find the final summary here). The data gathered have been very influential for the next steps. You can now expect over the coming weeks and months to see updates on the various specifications that compose the Java EE platform. Some Specification Leads are busy gathering additional feedback regarding what they should focus their efforts on (e.g. CDI 2 survey). Other Specification Leads have already publicly exposed what they think should be one of the focus for the evolution of the specification they lead.  For example, adding Server-Senet Events (SSE) support in JAX-RS is being discussed here and adding MVC support is being discussed here. Please remember that the fact we are now discussing any feature does not insure that it will be included in the proposal, nor in any particular update to Java EE. We can expect additional enhancements, changes and evolutions as we get closer to the finalisation of the different specifications... and there is still a long way to go with these specification proposals! Linda DeMichiel, Java EE Co-Specification Lead, has recently posted a draft proposal for the Java EE 8 Platform specification. Linda's goal is to recruit people and companies supporting this proposal before submitting it to the JCP.  This draft proposal is very interesting reading as it contains relevant information on the plans for Java EE 8 such as : The themes: Support for the latest web standards (eg. HTTP 2.0)  Continue to work on ease of development Improve the infrastructure for cloud support Alignment with Java SE 8 New JSRs to be added to the platform: J-Cache Java API for JSON Binding Java Configuration Plans for the Web Profile Plans on technologies to prune in Java EE 8, ... So if you haven't done it yet, I really encourage you to read the Java EE 8 draft proposal! Our goal for the Java EE 8 specification is for it to be finalized in the second half of 2016. It is important to note that we are in the early days of Java EE 8 and at this stage everything (themes, content, timing, etc.) is preliminary. Everything still needs to be discussed, challenged and agreed within the different Java Community Process (JCP) Experts Groups (EGs). Some EGs that still need to be formed! It could also means that the roadmap will have to be adjusted to follow the progress being made in the different EGs. This is also a good occasion to remind you that participation within those upcoming JCP Experts Groups is encouraged. Contributing in an EG is an effective lever to influence what Java EE 8 will become! Finally, as things get more concrete, we will share details on how to engage in the different Java EE 8 related Adopt-a-JSR initiatives, another way to contribute. You can also read other posts related to Java EE 8, here at The Aquarium blog. Just look for articles with the 'javaee8' tag.

  Read the article

• design a model for a system of dependent variables

  - by dbaseman

  I'm dealing with a modeling system (financial) that has dozens of variables. Some of the variables are independent, and function as inputs to the system; most of them are calculated from other variables (independent and calculated) in the system. What I'm looking for is a clean, elegant way to: define the function of each dependent variable in the system trigger a re-calculation, whenever a variable changes, of the variables that depend on it A naive way to do this would be to write a single class that implements INotifyPropertyChanged, and uses a massive case statement that lists out all the variable names x1, x2, ... xn on which others depend, and, whenever a variable xi changes, triggers a recalculation of each of that variable's dependencies. I feel that this naive approach is flawed, and that there must be a cleaner way. I started down the path of defining a CalculationManager<TModel> class, which would be used (in a simple example) something like as follows: public class Model : INotifyPropertyChanged { private CalculationManager<Model> _calculationManager = new CalculationManager<Model>(); // each setter triggers a "PropertyChanged" event public double? Height { get; set; } public double? Weight { get; set; } public double? BMI { get; set; } public Model() { _calculationManager.DefineDependency<double?>( forProperty: model => model.BMI, usingCalculation: (height, weight) => weight / Math.Pow(height, 2), withInputs: model => model.Height, model.Weight); } // INotifyPropertyChanged implementation here } I won't reproduce CalculationManager<TModel> here, but the basic idea is that it sets up a dependency map, listens for PropertyChanged events, and updates dependent properties as needed. I still feel that I'm missing something major here, and that this isn't the right approach: the (mis)use of INotifyPropertyChanged seems to me like a code smell the withInputs parameter is defined as params Expression<Func<TModel, T>>[] args, which means that the argument list of usingCalculation is not checked at compile time the argument list (weight, height) is redundantly defined in both usingCalculation and withInputs I am sure that this kind of system of dependent variables must be common in computational mathematics, physics, finance, and other fields. Does someone know of an established set of ideas that deal with what I'm grasping at here? Would this be a suitable application for a functional language like F#? Edit More context: The model currently exists in an Excel spreadsheet, and is being migrated to a C# application. It is run on-demand, and the variables can be modified by the user from the application's UI. Its purpose is to retrieve variables that the business is interested in, given current inputs from the markets, and model parameters set by the business.

  Read the article

• Java Embedded Releases

  - by Tori Wieldt

  Oracle today announced a new product in its Java Platform, Micro Edition (Java ME) product portfolio, Oracle Java ME Embedded 3.2, a complete client Java runtime Optimized for resource-constrained, connected, embedded systems.  Also, Oracle is releasing Oracle Java Wireless Client 3.2, Oracle Java ME Software Development Kit (SDK) 3.2. Oracle also announced Oracle Java Embedded Suite 7.0 for larger embedded devices, providing a middleware stack for embedded systems. Small is the new big! Introducing Oracle Java ME Embedded 3.2  Oracle Java ME Embedded 3.2 is designed and optimized to meet the unique requirements of small embedded, low power devices such as micro-controllers and other resource-constrained hardware without screens or user interfaces. These include: On-the-fly application downloads and updates Remote operation, often in challenging environments Ability to add new capabilities without impacting the existing functions Support for hardware with as little as 130 kB RAM and 350 kB ROM Oracle Java Wireless Client 3.2 Oracle Java Wireless Client 3.2 is built around an optimized Java ME implementation that delivers a feature-rich application environment for mass-market mobile devices. This new release: Leverages standard JSRs, Oracle optimizations/APIs and a flexible porting layer for device specific customizations, which are tuned to device/chipset requirements Supports advanced tooling functions, such as memory and network monitoring and on-device tooling Offers new support for dual SIM functionality, which is highly useful for mass-market devices supported by multiple carriers with multiple phone connections Oracle Java ME SDK 3.2 Oracle Java ME SDK 3.2 provides a complete development environment for both Oracle Java ME Embedded 3.2 and Oracle Java Wireless Client 3.2. Available for download from OTN, The latest version includes: Small embedded device support In-field and remote administration and debugging Java ME SDK plug-ins for Eclipse and the NetBeans Integrated Development Environment (IDE), enabling more application development environments for Java ME developers. A new device skin creator that developers can use to generate their custom device skins for testing their applications. Oracle Embedded Suite 7.0 The Oracle Java Embedded Suite is a new packaged solution from Oracle (including Java DB, GlassFish for Embedded Suite, Jersey Web Services Framework, and Oracle Java SE Embedded 7 platform), created to provide value added services for collecting, managing, and transmitting data to and from other embedded devices.The Oracle Java Embedded Suite is a complete device-to-data center solution subset for embedded systems.  See Java Me and Java Embedded in Action Java ME and Java Embedded technologies will be showcased for developers at JavaOne 2012 in over 60 conference sessions and BOFs, as well as in the JavaOne Exhibition Hall. For business decision makers, the new event Java Embedded @ JavaOne you learn more about Java Embedded technologies and solutions.

  Read the article

• Using HBase or Cassandra for a token server

  - by crippy

  I've been trying to figure out how to use HBase/Cassandra for a token system we're re-implementing. I can probably squeeze quite a lot more from MySQL, but it just seems it has come to clinging on to the wrong tool for the task just because we know it well. Eventually will hit a wall (like happened to us in other areas). Naturally I started looking into possible NoSQL solutions. The prominent ones (at least in terms of buzz) are HBase and Cassandra. The story is more or less like this: A user can send a gift other users. Each gift has a list of recipients or is public in which case limited by number or expiration date For each gift sent we generate some token that uniquely identifies that gift. For each gift we track the list of potential recipients and their current status relating to that gift (accepted, declinded etc). A user can request to see all his currently pending gifts A can request a list of users he has sent a gift to today (used to limit number of gifts sent) Required the ability to "dump" or "ignore" expired gifts (x day old gifts are considered expired) There are some other requirements but I believe the above covers the essentials. How would I go and model that using HBase or Cassandra? Well, the wall was performance. A few 10s of millions of records per day over 2 tables kept for 2 weeks (wish I could have kept it for more but there was no way). The response times kept getting slower and slower until eventually we had to start cutting down number of days we kept data. Caching helps here but it's not an ideal solution since a big part of the ops are updates. Also, as I hinted in my original post. We use MySQL extensively. We know exactly what it can and can't do both in naive implementations followed by native partitioning and finally by horizontally sharding our dataset on the application level to reside on multiple DB nodes. It can be done, but that's not really what I'm trying to get from this. I asked a very specific question about designing a solution using a NoSQL solution since it's very hard to find examples for designs out there. Brainlag, not trying to come off as rude. I actually appreciate it a lot that you are the only one who even bothered to respond. but I see it over and over again. People ask questions and others assume they have no idea what they're talking about and give an irrelevant answer. Ignore RDBMS please. The question is about nosql.

  Read the article

• USB Drive Warm Boot Issue. Cold boot = Perfect. Warm boot = "No boot sector found on USB device"

  - by Dan

  I'm experiencing a boot/reboot quirk similar to, yet somewhat different from others posted here. I have two Western Digital "Passport" external USB2 drives (160GB and 320GB) with Ubuntu 11.10 installed. The BIOS on my laptop is set to boot USB drives before the internal drive, and it works well. Either drive will cold-boot Ubuntu 11.10 perfectly. However, at times the computer must be restarted (warm boot) to have software updates or other changes take effect. When I warm-boot the computer, the computer goes through its normal shutdown/restart, then the usual BIOS tests, at which time the USB drive is selected momentarily (as normal), and that's when the trouble starts. I get a "No boot sector found on USB device", and the computer proceeds to boot Windows from the internal drive. If I press F12 early during the restart sequence (allows manual selection of the boot sequence), USB is still shown before the internal drive on the sequence list (as it should be). If I highlight "USB" and press ENTER, I still get a "No boot sector..." error message, but the external USB drive then proceeds to boot Ubuntu normally. I have a third external USB drive (Western Digital 160 GB Media Center) that cold-boots and warm-boots perfectly, so I know everything in the computer is set up properly. It also tells me Ubuntu is set up correctly on the drives, as all three drives were done identically, and at the same time. I've tried formatting the Passport drives NTFS and FAT32, but it didn't change anything. If I power-down the computer, then start it up again, it will boot Ubuntu from either of the Passport drives perfectly - every time. It's as if during a warm boot the Passport drives are somehow looking for the boot loader in the wrong location on the drive - yet either drives works when booting from a cold start. Not a show-stopper .. but frustrating. Computer is a Dell XPS M1530, A12 BIOS (latest), but I don't think the computer plays into the issue because one of the three drives works at all times. It's only the two WD Passport models at issue here. Thanks!

  Read the article

• Ubuntu 12.10 graphics does not work properly

  - by madox2

  My graphic on ubuntu 12.10 does not work as well as on 12.04. After upgrade I installed driver sudo apt-add-repository ppa:ubuntu-x-swat/x-updates sudo apt-get update sudo apt-get install nvidia-current for my Nvidia 450 GTS graphics card. But sometimes I see slight lag on my videos played in VLC player, some of desktop and window effects are lagging, sometimes I can see an indescribable souce of pixels on my screen at the start of ubuntu and so on. I feel difference between 12.04 and 12.10 in favour of former version. Does anyone know whats wrong or what I am missing? here is output of lspci -k: 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09) Kernel driver in use: pcieport Kernel modules: shpchp 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) Subsystem: Giga-byte Technology Device 1c3a Kernel driver in use: mei Kernel modules: mei 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) Subsystem: Giga-byte Technology Device 5006 Kernel driver in use: ehci_hcd 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) Subsystem: Giga-byte Technology Device a000 Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.4 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 5 (rev b5) Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) Subsystem: Giga-byte Technology Device 5006 Kernel driver in use: ehci_hcd 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev a5) 00:1f.0 ISA bridge: Intel Corporation H61 Express Chipset Family LPC Controller (rev 05) Subsystem: Giga-byte Technology Device 5001 Kernel driver in use: lpc_ich Kernel modules: lpc_ich 00:1f.2 IDE interface: Intel Corporation 6 Series/C200 Series Chipset Family 4 port SATA IDE Controller (rev 05) Subsystem: Giga-byte Technology Device b002 Kernel driver in use: ata_piix 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05) Subsystem: Giga-byte Technology Device 5001 Kernel modules: i2c-i801 00:1f.5 IDE interface: Intel Corporation 6 Series/C200 Series Chipset Family 2 port SATA IDE Controller (rev 05) Subsystem: Giga-byte Technology Device b002 Kernel driver in use: ata_piix 01:00.0 VGA compatible controller: NVIDIA Corporation GF116 [GeForce GTS 450] (rev a1) Subsystem: CardExpert Technology Device 0401 Kernel driver in use: nvidia Kernel modules: nvidia_current, nouveau, nvidiafb 01:00.1 Audio device: NVIDIA Corporation GF116 High Definition Audio Controller (rev a1) Subsystem: CardExpert Technology Device 0401 Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 03:00.0 Ethernet controller: Atheros Communications Inc. AR8151 v2.0 Gigabit Ethernet (rev c0) Subsystem: Giga-byte Technology Device e000 Kernel driver in use: atl1c Kernel modules: atl1c

  Read the article

• JDK bug migration milestone: JIRA now the system of record

  - by darcy

  I'm pleased to announce the OpenJDK bug database migration project has reached a significant milestone: the JDK has switched from the legacy Sun "bugtraq" system to a new internal JIRA instance as the system of record for our bug tracking. This completes the initial phase of the previously described plan of getting OpenJDK onto an externally visible and writable bug tracker. The identities contained in the current system include recognized OpenJDK contributors. The bug migration effort to date has been sizable in multiple dimensions. There are around 140,000 distinct issues imported into the JDK project of the JIRA instance, nearly 165,000 if backport issues to track multiple-release information are included. Separately, the Code Tools OpenJDK project has its own JIRA project populated with several thousands existing bugs. Once the OpenJDK JIRA instance is externalized, approved OpenJDK projects will be able to request the creation of a JIRA project for issue tracking. There are many differences in the schema used to model bugs between the legacy bug system and the schema for the new JIRA projects. We've favored simplifications to the existing system where possible and, after much discussion, we've settled on five main states for the OpenJDK JIRA projects: New Open In progress Resolved Closed The Open and In-progress states can have a substate Understanding field set to track whether the issues has its "Cause Known" or "Fix understood". In the closed state, a Verification field can indicate whether a fix has been verified, unverified, or if the fix has failed. At the moment, there will be very little externally visible difference between JIRA for OpenJDK and the legacy system it replaces. One difference is that bug numbers for newly filed issues in the JIRA JDK project will be 8000000 and above. If you are working with JDK Hg repositories, update any local copies of jcheck to the latest version which recognizes this expanded bug range. (The bug numbers of existing issues have been preserved on the import into JIRA). Relatively soon, we plan for the pages published on bugs.sun.com to be generated from information in JIRA rather than in the legacy system. When this occurs, there will be some differences in the page display and the terminology used will be revised to reflect JIRA usage, such as referring to the "component/subcomponent" of an issue rather than its "category". The exact timing of this transition will be announced when it is known. We don't currently have a firm timeline for externalization of the JIRA system. Updates will be provided as they become available. However, that is unlikely to happen before JavaOne next week!

  Read the article

• How to handle this unfortunately non hypothetical situation with end-users?

  - by User Smith

  I work in a medium sized company but with a very small IT force. Last year (2011), I wrote an application that is very popular with a large group of end-users. We hit a deadline at the end of last year and some functionality (I will call funcA from now on) was not added into the application that was wanted at the very end. So, this application has been running in live/production since the end of 2011, I might add without issue. Yesterday, a whole group of end-users started complaining that funcA that was never in the application is no longer working. Our priority at this company is that if an application is broken it must be fixed first prior to prioritized projects. I have compared code and queries and there is no difference since 2011, which is proofA. I then was able to get one of the end-users to admit that it never worked proofB, but since then that end-user has went back and said that it was working previously......I believe the horde of end-users has assimilated her. I have also reviewed my notes for this project which has requirements and daily updates regarding the project which specifically states, "funcA not achieved due to time constraints", proofC. I have spoken with many of them and I can see where they could be confused as they are very far from a programming background, but I also know they are intelligent enough to act in a group in order to bypass project prioritization orders in order to get functionality that they want to make their job easier. The worst part is is that now group think is setting in and my boss and the head of IT is actually starting to believe them, even though there is no code or query changes. As far as reviewing the state of the logic it is very cut and dry to the point of if 1 = 1, funcA will not work. So, this is the end of the description of my scenario, but I am trying not to get severally dinged on my performance metrics due to this which would essentially have me moved to fixing a production problem that doesn't exist that will probably take over 1 month. I am looking for direct answers to this question. This question is not for rants, polling, or discussions as this is not the format for StackExchange. Please don't downvote me too terribly it is pretty common on this specific site of stack, I am looking for honest answers to this situation and I couldn't find a forum more appropriate.

  Read the article

< Previous Page | 201 202 203 204 205 206 207 208 209 210 211 212  | Next Page >