Search Results

Search found 5436 results on 218 pages for 'transfer rate'.

Page 205/218 | < Previous Page | 201 202 203 204 205 206 207 208 209 210 211 212  | Next Page >

• Understanding Windows 8 Recovery options

  - by stuffe

  Background: I am preparing a PC that I am sending to a relative abroad, who has little or no internet access, and next to no sensible options for getting IT support should anything go wrong. As such I am trying to provide a full set of recovery options such that they are able to reinstall the OS with minimum fuss or assistance if required. The PC is a brand new Acer laptop that came with Windows 7 pre-installed (and an associated recovery partition) and a free upgrade to Windows 8. I have installed Windows 8 from scratch performing a format and clean install from media I burned from the official download. The existing Windows 7 recovery partition is still there, and I can still boot from it. I have created recovery DVDs of that in case it is ever lost. Here are my recovery options so far. I can perform a factory reset of Win 7 via the recovery partition I can perform a factory reset of Win 7 via burned recovery DVDs I can re-install Windows 8 cleanly from a DVD All of these are useful, but not what I want, because the first 2 methods use Win 7, and still fill the machine with crapware, and the latter doesn't provide for any post-install customisation and software installation. So, I am looking to see what other options are available to perform a Windows 8 recovery that will be more than a simple install. I am aware that Win8 comes with some useful refresh tools: Refresh your PC - Re-install Win 8 over the top of your existing installation, recovering from any Windows corruption etc. I can run this from my current install, although it says some files are missing that will be provided by me install or recovery media, which seems to be code for stick your install DVD in, and it starts after I do that - unfortunately for this particular laptop you need to specify a particular WIFI driver or the install bombs out part way through with IRQL errors, and this refresh method skips the part where you can load a driver, so it's no use to me. I think I can fix this by creating a custom recovery image using the recimg.exe command but it takes hours to complete so I haven't tried it yet. Reset your PC - Perform a full install and lose all your files. Again it needs my Install media inserting before it will do anything, but then it provides an error (will include later when I recreate it...) Now, these recovery options look useful (in principal, although both are fail for me) but they rely on having a working system to access the tools, which leads me to the last option, of making a Recovery USB drive. I have made a recovery drive, and it should perform loads of useful things, including copying my WIN7 recovery partition to the drive, providing the above refresh and reset options, providing other troubleshooting options and also the ability to restore from a custom image, only none of them seem to work for me. Creating the Recovery Drive - the option to include my recovery partition is greyed out. The partition exists and works fine, why will it not copy it? Refresh - I imagine this would have the same issues as I described before, but this is moot because when I try it says that the "drive where Windows is installed is locked, please unlock the drive and try again" with no info on what that means and how to do it. Restore - Again, probably pointless as I can just use the DVD, but it also errors: "unable to reset your PC. A required drive partition is missing" System Restore - should let me roll back a bad driver etc as per normal in Windows, only it simply says "To use system restore you must specify which windows installation to restore. Restart this computer, select an operating system, and select system restore" ?!?! System Image Recovery - this seems to be offering to restore from a Windows system image, but this is deprecated in Windows 8, although you can still make one if you use the Windows 7 Backup tools, however the resultant file is too large to put on the USB stick as it's FAT formatted, and would be a massive stack of DVDs anyway. So useless. It would be nice it it would work with the custom recovery image you can use with the refresh command, but there seems no option to do this. Automatic Repair - some diagnostics, which seem useless as it happily tells me it can't fix my problem, even though I have none. Command Prompt - yay, this works! What on earth do I want to use it for... Had any of the above worked, it might be useful, but as any form of install still requires you to have the DVD, and any form of custom recovery image also requires you to have either a massive stack of DVDs or an NTFS formatted backup device in addition to the recovery drive, it sort of ruins the point. It doesn't seem rocket science. I want to create a bootable USB drive that I can refresh Windows over an existing install with, perform a clean reinstall to a bare system, or recovery a customised image with existing apps installed. If anyone can point me in a direction that allows me to make a single recovery drive do these all these things, I would appreciate it. I have a 32Gb USB3 thumb drive that I bought for this very purpose, but it's seems to be fighting to let me do anything useful. At this rate I will be making a DriveImageXML recovery stick and dumping the OS with that, which I know works, but isn't so elegant as using the proper tools..

  Read the article

• 500 Internal Server Error with PHP application

  - by James

  I have written a PHP application using Windows and XAMPP. I've been trying to run it on Ubuntu 10.10 with Lighttpd 1.4.26. Parts of the application work fine, but whenever I try to log in, I get a 500 - Internal Server Error page. The only thing that shows up in /var/log/lighttpd/error.log is 2011-02-25 13:43:13: (mod_fastcgi.c.2582) unexpected end-of-file (perhaps the fastcgi process died): pid: 1169 socket: unix:/tmp/php.socket-0 2011-02-25 13:43:13: (mod_fastcgi.c.3367) response not received, request sent: 1596 on socket: unix:/tmp/php.socket-0 for /~denton/customer-facing-portal/index.php?, closing connection If I had any output whatsoever from PHP, this would be a lot easier to debug. Any ideas on how to get some? Here is my /etc/lighttpd/lighttpd.conf file: # Debian lighttpd configuration file # ############ Options you really have to take care of #################### ## modules to load server.modules = ( "mod_alias", "mod_compress", # "mod_rewrite", # "mod_redirect", # "mod_usertrack", # "mod_expire", # "mod_flv_streaming", # "mod_evasive", "mod_setenv" ) ## a static document-root, for virtual-hosting take look at the ## server.virtual-* options server.document-root = "/var/www/" ## where to upload files to, purged daily. server.upload-dirs = ( "/var/cache/lighttpd/uploads" ) ## where to send error-messages to server.errorlog = "/var/log/lighttpd/error.log" ## files to check for if .../ is requested index-file.names = ( "index.php", "index.html", "index.htm", "default.htm", "index.lighttpd.html" ) ## Use the "Content-Type" extended attribute to obtain mime type if possible # mimetype.use-xattr = "enable" ## # which extensions should not be handle via static-file transfer # # .php, .pl, .fcgi are most often handled by mod_fastcgi or mod_cgi static-file.exclude-extensions = ( ".php", ".pl", ".fcgi" ) ######### Options that are good to be but not neccesary to be changed ####### ## Use ipv6 only if available. (disabled for while, check #560837) #include_shell "/usr/share/lighttpd/use-ipv6.pl" ## bind to port (default: 80) # server.port = 81 ## bind to localhost only (default: all interfaces) ## server.bind = "localhost" ## error-handler for status 404 #server.error-handler-404 = "/error-handler.html" #server.error-handler-404 = "/error-handler.php" ## to help the rc.scripts server.pid-file = "/var/run/lighttpd.pid" ## ## Format: <errorfile-prefix><status>.html ## -> ..../status-404.html for 'File not found' #server.errorfile-prefix = "/var/www/" ## virtual directory listings dir-listing.encoding = "utf-8" server.dir-listing = "enable" ### only root can use these options # # chroot() to directory (default: no chroot() ) #server.chroot = "/" ## change uid to <uid> (default: don't change) server.username = "www-data" ## change gid to <gid> (default: don't change) server.groupname = "www-data" #### compress module compress.cache-dir = "/var/cache/lighttpd/compress/" compress.filetype = ("text/plain", "text/html", "application/x-javascript", "text/css") #### url handling modules (rewrite, redirect, access) # url.rewrite = ( "^/$" => "/server-status" ) # url.redirect = ( "^/wishlist/(.+)" => "http://www.123.org/$1" ) #### expire module # expire.url = ( "/buggy/" => "access 2 hours", "/asdhas/" => "access plus 1 seconds 2 minutes") #### external configuration files ## mimetype mapping include_shell "/usr/share/lighttpd/create-mime.assign.pl" ## load enabled configuration files, ## read /etc/lighttpd/conf-available/README first include_shell "/usr/share/lighttpd/include-conf-enabled.pl" ## Set environment variables setenv.add-environment = ( "DB_URL__DEMO" => "192.168.1.231", "DB_NAME_DEMO" => "demo", "DB_USER_DEMO" => "user", "DB_PASS_DEMO" => "password", "DB_AGENCY_DEMO" => "demo" ) Here is my /etc/php5/cgi/php.ini file (sans 1641 lines of comments): [PHP] register_long_arrays = Off short_open_tag = Off engine = On short_open_tag = Off asp_tags = Off precision = 14 y2k_compliance = On output_buffering = 4096 zlib.output_compression = Off implicit_flush = Off unserialize_callback_func = serialize_precision = 100 allow_call_time_pass_reference = Off safe_mode = Off safe_mode_gid = Off safe_mode_include_dir = safe_mode_exec_dir = safe_mode_allowed_env_vars = PHP_ safe_mode_protected_env_vars = LD_LIBRARY_PATH disable_functions = disable_classes = expose_php = On max_execution_time = 30 max_input_time = 60 memory_limit = 128M error_reporting = E_ALL & ~E_DEPRECATED & ~E_STRICT display_errors = On display_startup_errors = On log_errors = On log_errors_max_len = 1024 ignore_repeated_errors = Off ignore_repeated_source = Off report_memleaks = On track_errors = On html_errors = On variables_order = "GPCS" request_order = "GP" register_globals = Off register_long_arrays = Off register_argc_argv = Off auto_globals_jit = On post_max_size = 8M magic_quotes_gpc = Off magic_quotes_runtime = Off magic_quotes_sybase = Off auto_prepend_file = auto_append_file = default_mimetype = "text/html" doc_root = user_dir = enable_dl = Off cgi.fix_pathinfo=1 file_uploads = On upload_max_filesize = 2M max_file_uploads = 20 allow_url_fopen = On allow_url_include = Off default_socket_timeout = 60 [Date] date.timezone = "America/Chicago" [filter] [iconv] [intl] [sqlite] [sqlite3] [Pcre] [Pdo] [Pdo_mysql] pdo_mysql.cache_size = 2000 pdo_mysql.default_socket= [Phar] [Syslog] define_syslog_variables = Off [mail function] SMTP = localhost smtp_port = 25 mail.add_x_header = On [SQL] sql.safe_mode = Off [ODBC] odbc.allow_persistent = On odbc.check_persistent = On odbc.max_persistent = -1 odbc.max_links = -1 odbc.defaultlrl = 4096 odbc.defaultbinmode = 1 [Interbase] ibase.allow_persistent = 1 ibase.max_persistent = -1 ibase.max_links = -1 ibase.timestampformat = "%Y-%m-%d %H:%M:%S" ibase.dateformat = "%Y-%m-%d" ibase.timeformat = "%H:%M:%S" [MySQL] mysql.allow_local_infile = On mysql.allow_persistent = On mysql.cache_size = 2000 mysql.max_persistent = -1 mysql.max_links = -1 mysql.default_port = mysql.default_socket = mysql.default_host = mysql.default_user = mysql.default_password = mysql.connect_timeout = 60 mysql.trace_mode = Off [MySQLi] mysqli.max_persistent = -1 mysqli.allow_persistent = On mysqli.max_links = -1 mysqli.cache_size = 2000 mysqli.default_port = 3306 mysqli.default_socket = mysqli.default_host = mysqli.default_user = mysqli.default_pw = mysqli.reconnect = Off [mysqlnd] mysqlnd.collect_statistics = On mysqlnd.collect_memory_statistics = Off [OCI8] [PostgresSQL] pgsql.allow_persistent = On pgsql.auto_reset_persistent = Off pgsql.max_persistent = -1 pgsql.max_links = -1 pgsql.ignore_notice = 0 pgsql.log_notice = 0 [Sybase-CT] sybct.allow_persistent = On sybct.max_persistent = -1 sybct.max_links = -1 sybct.min_server_severity = 10 sybct.min_client_severity = 10 [bcmath] bcmath.scale = 0 [browscap] [Session] session.save_handler = files session.use_cookies = 1 session.use_only_cookies = 1 session.name = PHPSESSID session.auto_start = 0 session.cookie_lifetime = 0 session.cookie_path = / session.cookie_domain = session.cookie_httponly = session.serialize_handler = php session.gc_probability = 1 session.gc_divisor = 1000 session.gc_maxlifetime = 1440 session.bug_compat_42 = Off session.bug_compat_warn = Off session.referer_check = session.entropy_length = 0 session.cache_limiter = nocache session.cache_expire = 180 session.use_trans_sid = 0 session.hash_function = 0 session.hash_bits_per_character = 5 url_rewriter.tags = "a=href,area=href,frame=src,input=src,form=fakeentry" [MSSQL] mssql.allow_persistent = On mssql.max_persistent = -1 mssql.max_links = -1 mssql.min_error_severity = 10 mssql.min_message_severity = 10 mssql.compatability_mode = Off mssql.secure_connection = Off [Assertion] [COM] [mbstring] [gd] [exif] [Tidy] tidy.clean_output = Off [soap] soap.wsdl_cache_enabled=1 soap.wsdl_cache_dir="/tmp" soap.wsdl_cache_ttl=86400 soap.wsdl_cache_limit = 5 [sysvshm] [ldap] ldap.max_links = -1 [mcrypt] [dba] Update: here is /etc/lighttpd/conf-enabled/15-fastcgi-php.conf As far as I know, it's just the default config file the Ubuntu package installed. ## FastCGI programs have the same functionality as CGI programs, ## but are considerably faster through lower interpreter startup ## time and socketed communication ## ## Documentation: /usr/share/doc/lighttpd-doc/fastcgi.txt.gz ## http://redmine.lighttpd.net/projects/lighttpd/wiki/Docs:ConfigurationOptions#mod_fastcgi-fastcgi ## Start an FastCGI server for php (needs the php5-cgi package) fastcgi.server += ( ".php" => (( "bin-path" => "/usr/bin/php-cgi", "socket" => "/tmp/php.socket", "max-procs" => 1, "idle-timeout" => 20, "bin-environment" => ( "PHP_FCGI_CHILDREN" => "4", "PHP_FCGI_MAX_REQUESTS" => "10000" ), "bin-copy-environment" => ( "PATH", "SHELL", "USER" ), "broken-scriptfilename" => "enable" )) )

  Read the article

• Exposing the AnyConnect HTTPS service to outside network

  - by Maciej Swic

  We have a Cisco ASA 5505 with firmware ASA9.0(1) and ASDM 7.0(2). It is configured with a public ip address, and when trying to reach it from the outside by HTTPS for AnyConnect VPN, we get the following log output: 6 Nov 12 2012 07:01:40 <client-ip> 51000 <asa-ip> 443 Built inbound TCP connection 2889 for outside:<client-ip>/51000 (<client-ip>/51000) to identity:<asa-ip>/443 (<asa-ip>/443) 6 Nov 12 2012 07:01:40 <client-ip> 50999 <asa-ip> 443 Built inbound TCP connection 2890 for outside:<client-ip>/50999 (<client-ip>/50999) to identity:<asa-ip>/443 (<asa-ip>/443) 6 Nov 12 2012 07:01:40 <client-ip> 51000 <asa-ip> 443 Teardown TCP connection 2889 for outside:<client-ip>/51000 to identity:<asa-ip>/443 duration 0:00:00 bytes 0 No valid adjacency 6 Nov 12 2012 07:01:40 <client-ip> 50999 <asa-ip> 443 Teardown TCP connection 2890 for outside:<client-ip>/50999 to identity:<asa-ip>/443 duration 0:00:00 bytes 0 No valid adjacency We finished the startup wizard and the anyconnect vpn wizard and here is the resulting configuration: Cryptochecksum: 12262d68 23b0d136 bb55644a 9c08f86b : Saved : Written by enable_15 at 07:08:30.519 UTC Mon Nov 12 2012 ! ASA Version 9.0(1) ! hostname vpn domain-name office.<redacted>.com enable password <redacted> encrypted passwd <redacted> encrypted names ip local pool vpn-pool 192.168.67.2-192.168.67.253 mask 255.255.255.0 ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! interface Vlan1 nameif inside security-level 100 ip address 192.168.68.250 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address <redacted> 255.255.255.248 ! ftp mode passive dns server-group DefaultDNS domain-name office.<redacted>.com object network obj_any subnet 0.0.0.0 0.0.0.0 pager lines 24 logging enable logging asdm informational mtu outside 1500 mtu inside 1500 icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 14400 no arp permit-nonconnected ! object network obj_any nat (inside,outside) dynamic interface timeout xlate 3:00:00 timeout pat-xlate 0:00:30 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy user-identity default-domain LOCAL http server enable http 192.168.68.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart crypto ipsec ikev2 ipsec-proposal DES protocol esp encryption des protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal 3DES protocol esp encryption 3des protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES protocol esp encryption aes protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES192 protocol esp encryption aes-192 protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES256 protocol esp encryption aes-256 protocol esp integrity sha-1 md5 crypto ipsec security-association pmtu-aging infinite crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map outside_map interface outside crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map inside_map interface inside crypto ca trustpoint _SmartCallHome_ServerCA crl configure crypto ca trustpoint ASDM_TrustPoint0 enrollment self subject-name CN=vpn proxy-ldc-issuer crl configure crypto ca trustpool policy crypto ca certificate chain _SmartCallHome_ServerCA certificate ca 6ecc7aa5a7032009b8cebcf4e952d491 <redacted> quit crypto ca certificate chain ASDM_TrustPoint0 certificate f678a050 <redacted> quit crypto ikev2 policy 1 encryption aes-256 integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 10 encryption aes-192 integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 20 encryption aes integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 30 encryption 3des integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 40 encryption des integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 enable outside client-services port 443 crypto ikev2 remote-access trustpoint ASDM_TrustPoint0 telnet timeout 5 ssh 192.168.68.0 255.255.255.0 inside ssh timeout 5 console timeout 0 vpn-addr-assign local reuse-delay 60 dhcpd auto_config outside ! dhcpd address 192.168.68.254-192.168.68.254 inside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept ssl trust-point ASDM_TrustPoint0 inside ssl trust-point ASDM_TrustPoint0 outside webvpn enable outside enable inside anyconnect image disk0:/anyconnect-win-3.1.01065-k9.pkg 1 anyconnect image disk0:/anyconnect-linux-3.1.01065-k9.pkg 2 anyconnect image disk0:/anyconnect-macosx-i386-3.1.01065-k9.pkg 3 anyconnect profiles GM-AnyConnect_client_profile disk0:/GM-AnyConnect_client_profile.xml anyconnect enable tunnel-group-list enable group-policy GroupPolicy_GM-AnyConnect internal group-policy GroupPolicy_GM-AnyConnect attributes wins-server none dns-server value 192.168.68.254 vpn-tunnel-protocol ikev2 ssl-client default-domain value office.<redacted>.com webvpn anyconnect profiles value GM-AnyConnect_client_profile type user username <redacted> password <redacted> encrypted tunnel-group GM-AnyConnect type remote-access tunnel-group GM-AnyConnect general-attributes address-pool vpn-pool default-group-policy GroupPolicy_GM-AnyConnect tunnel-group GM-AnyConnect webvpn-attributes group-alias GM-AnyConnect enable ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum client auto message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect esmtp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp inspect ip-options ! service-policy global_policy global prompt hostname context call-home reporting anonymous Cryptochecksum:12262d6823b0d136bb55644a9c08f86b : end Clearly we are missing something, but the question is, what?

  Read the article

• Bandwidth Limit User

  - by user45611

  Hello, i'm saxtor i would like to know how to limit users bandwidth for 10gb per day however i dont want to limit them by ipaddress because if they where to go to an internet cafe the users at the cafe will be restricted with that quota, i need to log them via sockets, example the user request to download a file from http://localhost with there username and password, when they download the file sql will update there bandwidth they used, i have a script here but its not working my buffer doesnt work that rate when a user uses multiple connections thanks for the help!. /** * @author saxtor if you can improve this code email me @saxtorinc.com * @copyright 2010 / /* * CREATE TABLE IF NOT EXISTS max_traffic ( id int(255) NOT NULL AUTO_INCREMENT, limit int(255) NOT NULL, PRIMARY KEY (id) ) ENGINE=MyISAM DEFAULT CHARSET=latin1 AUTO_INCREMENT=0 ; */ //SQL Connection [this is hackable for testing] date_default_timezone_set("America/Guyana"); mysql_connect("localhost", "root", "") or die(mysql_error()); mysql_select_db("Quota") or die(mysql_error()); function quota($id) { $result = mysql_query("SELECT `limit` FROM max_traffic WHERE id='$id' ") or die(error_log(mysql_error()));; $row = mysql_fetch_array($result); return $row[0]; } function update_quota($id,$value) { $result = mysql_query("UPDATE `max_traffic` SET `limit`='$value' WHERE id='$id'") or die(mysql_error()); return $value; } if ( quota(1) != 0) $limit = quota(1); else $limit = 0; $multipart = false; //was a part of the file requested? (partial download) $range = $_SERVER["HTTP_RANGE"]; if ($range) { //pass client Range header to rapidshare // _insert($range); $cookie .= "\r\nRange: $range"; $multipart = true; header("X-UR-RANGE-Range: $range"); } $url = 'http://127.0.0.1/puppy.iso'; $filename = basename($url); //octet-stream + attachment = client always stores file header('Content-type: application/octet-stream'); header('Content-Disposition: attachment; filename="'.$filename.'"'); //always included so clients know this script supports resuming header("Accept-Ranges: bytes"); //awful hack to pass rapidshare the premium cookie $user_agent = ini_get("user_agent"); ini_set("user_agent", $user_agent . "\r\nCookie: enc=$cookie"); $httphandle = fopen($url, "r"); $headers = stream_get_meta_data($httphandle); $size = $headers["wrapper_data"][6]; $sizer = explode(' ',$size); $size = $sizer[1]; //let's check the return header of rapidshare for range / length indicators //we'll just pass these to the client foreach ($headers["wrapper_data"] as $header) { $header = trim($header); if (substr(strtolower($header), 0, strlen("content-range")) == "content-range") { // _insert($range); header($header); header("X-RS-RANGE-" . $header); $multipart = true; //content-range indicates partial download } elseif (substr(strtolower($header), 0, strlen("Content-Length")) == "content-length") { // _insert($range); header($header); header("X-RS-CL-" . $header); } } if ($multipart) header('HTTP/1.1 206 Partial Content'); flush(); $speed = 4128; $packet = 1; //this is private dont touch. $bufsize = 128; //this is private dont touch/ $bandwidth = 0; //this is private dont touch. while (!(connection_aborted() || connection_status() == 1) && $size > 0) { while (!feof($httphandle) && $size > 0) { if ($limit <= 0 ) $size = 0; if ( $size < $bufsize && $size != 0 && $limit != 0) { echo fread($httphandle,$size); $bandwidth += $size; } else { if( $limit != 0) echo fread($httphandle,$bufsize); $bandwidth += $bufsize; } $size -= $bufsize; $limit -= $bufsize; flush(); if ($speed > 0 && ($bandwidth > $speed*$packet*103)) { usleep(100000); $packet++; //update_quota(1,$limit); } error_log(update_quota(1,$limit)); $limit = quota(1); //if( $size <= 0 ) // exit; } fclose($httphandle); } exit; ?

  Read the article

• Cisco ASA - Enable communication between same security level

  - by Conor

  I have recently inherited a network with a Cisco ASA (running version 8.2). I am trying to configure it to allow communication between two interfaces configured with the same security level (DMZ-DMZ) "same-security-traffic permit inter-interface" has been set, but hosts are unable to communicate between the interfaces. I am assuming that some NAT settings are causing my issue. Below is my running config: ASA Version 8.2(3) ! hostname asa enable password XXXXXXXX encrypted passwd XXXXXXXX encrypted names ! interface Ethernet0/0 switchport access vlan 400 ! interface Ethernet0/1 switchport access vlan 400 ! interface Ethernet0/2 switchport access vlan 420 ! interface Ethernet0/3 switchport access vlan 420 ! interface Ethernet0/4 switchport access vlan 450 ! interface Ethernet0/5 switchport access vlan 450 ! interface Ethernet0/6 switchport access vlan 500 ! interface Ethernet0/7 switchport access vlan 500 ! interface Vlan400 nameif outside security-level 0 ip address XX.XX.XX.10 255.255.255.248 ! interface Vlan420 nameif public security-level 20 ip address 192.168.20.1 255.255.255.0 ! interface Vlan450 nameif dmz security-level 50 ip address 192.168.10.1 255.255.255.0 ! interface Vlan500 nameif inside security-level 100 ip address 192.168.0.1 255.255.255.0 ! ftp mode passive clock timezone JST 9 same-security-traffic permit inter-interface same-security-traffic permit intra-interface object-group network DM_INLINE_NETWORK_1 network-object host XX.XX.XX.11 network-object host XX.XX.XX.13 object-group service ssh_2220 tcp port-object eq 2220 object-group service ssh_2251 tcp port-object eq 2251 object-group service ssh_2229 tcp port-object eq 2229 object-group service ssh_2210 tcp port-object eq 2210 object-group service DM_INLINE_TCP_1 tcp group-object ssh_2210 group-object ssh_2220 object-group service zabbix tcp port-object range 10050 10051 object-group service DM_INLINE_TCP_2 tcp port-object eq www group-object zabbix object-group protocol TCPUDP protocol-object udp protocol-object tcp object-group service http_8029 tcp port-object eq 8029 object-group network DM_INLINE_NETWORK_2 network-object host 192.168.20.10 network-object host 192.168.20.30 network-object host 192.168.20.60 object-group service imaps_993 tcp description Secure IMAP port-object eq 993 object-group service public_wifi_group description Service allowed on the Public Wifi Group. Allows Web and Email. service-object tcp-udp eq domain service-object tcp-udp eq www service-object tcp eq https service-object tcp-udp eq 993 service-object tcp eq imap4 service-object tcp eq 587 service-object tcp eq pop3 service-object tcp eq smtp access-list outside_access_in remark http traffic from outside access-list outside_access_in extended permit tcp any object-group DM_INLINE_NETWORK_1 eq www access-list outside_access_in remark ssh from outside to web1 access-list outside_access_in extended permit tcp any host XX.XX.XX.11 object-group ssh_2251 access-list outside_access_in remark ssh from outside to penguin access-list outside_access_in extended permit tcp any host XX.XX.XX.10 object-group ssh_2229 access-list outside_access_in remark http from outside to penguin access-list outside_access_in extended permit tcp any host XX.XX.XX.10 object-group http_8029 access-list outside_access_in remark ssh from outside to internal hosts access-list outside_access_in extended permit tcp any host XX.XX.XX.13 object-group DM_INLINE_TCP_1 access-list outside_access_in remark dns service to internal host access-list outside_access_in extended permit object-group TCPUDP any host XX.XX.XX.13 eq domain access-list dmz_access_in extended permit ip 192.168.10.0 255.255.255.0 any access-list dmz_access_in extended permit tcp any host 192.168.10.29 object-group DM_INLINE_TCP_2 access-list public_access_in remark Web access to DMZ websites access-list public_access_in extended permit object-group TCPUDP any object-group DM_INLINE_NETWORK_2 eq www access-list public_access_in remark General web access. (HTTP, DNS & ICMP and Email) access-list public_access_in extended permit object-group public_wifi_group any any pager lines 24 logging enable logging asdm informational mtu outside 1500 mtu public 1500 mtu dmz 1500 mtu inside 1500 no failover icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 60 global (outside) 1 interface global (dmz) 2 interface nat (public) 1 0.0.0.0 0.0.0.0 nat (dmz) 1 0.0.0.0 0.0.0.0 nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface 2229 192.168.0.29 2229 netmask 255.255.255.255 static (inside,outside) tcp interface 8029 192.168.0.29 www netmask 255.255.255.255 static (dmz,outside) XX.XX.XX.13 192.168.10.10 netmask 255.255.255.255 dns static (dmz,outside) XX.XX.XX.11 192.168.10.30 netmask 255.255.255.255 dns static (dmz,inside) 192.168.0.29 192.168.10.29 netmask 255.255.255.255 static (dmz,public) 192.168.20.30 192.168.10.30 netmask 255.255.255.255 dns static (dmz,public) 192.168.20.10 192.168.10.10 netmask 255.255.255.255 dns static (inside,dmz) 192.168.10.0 192.168.0.0 netmask 255.255.255.0 dns access-group outside_access_in in interface outside access-group public_access_in in interface public access-group dmz_access_in in interface dmz route outside 0.0.0.0 0.0.0.0 XX.XX.XX.9 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy http server enable http 192.168.0.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 telnet timeout 5 ssh 192.168.0.0 255.255.255.0 inside ssh timeout 20 console timeout 0 dhcpd dns 61.122.112.97 61.122.112.1 dhcpd auto_config outside ! dhcpd address 192.168.20.200-192.168.20.254 public dhcpd enable public ! dhcpd address 192.168.0.200-192.168.0.254 inside dhcpd enable inside ! threat-detection basic-threat threat-detection statistics host threat-detection statistics access-list no threat-detection statistics tcp-intercept ntp server 130.54.208.201 source public webvpn ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum client auto message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect ip-options inspect netbios inspect rsh inspect rtsp inspect skinny inspect esmtp inspect sqlnet inspect sunrpc inspect tftp inspect sip inspect xdmcp !

  Read the article

• Ubuntu, No wireless networks found after correctly installed madwifi

  - by Peter

  Hi, I just installed madwifi on my MSI laptop with an Atheros AR5001 wifi card & Lucid. As far as I can see and according to System - Administration - Hardware drivers the install was successful and the card + driver is up and running. However, I don't see any wireless network (my windows PC can see about 5 wireless networks). I tried it with the network manager applet as well as with wicd. If I try to connect to "Hidden Wireless Network" via nm-applet, it will start to connect for a while but is unable too (although I supply it with the correct WEP settings & key) So, I'm unable to use my wireless network. What am i doing wrong? Some information about my system: iwconfig lo no wireless extensions. eth0 no wireless extensions. wifi0 no wireless extensions. ath0 IEEE 802.11g ESSID:"" Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:17 dBm Sensitivity=1/1 Retry:off RTS thr:off Fragment thr:off Power Management:off Link Quality=0/70 Signal level=-96 dBm Noise level=-96 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 pan0 no wireless extensions. ifconfig ath0 Link encap:Ethernet HWaddr 00:15:af:cf:e2:ca inet6 addr: fe80::215:afff:fecf:e2ca/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth0 Link encap:Ethernet HWaddr 00:21:85:4d:82:78 inet addr:192.168.2.101 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::221:85ff:fe4d:8278/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3800 errors:0 dropped:0 overruns:0 frame:0 TX packets:2944 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3940261 (3.9 MB) TX bytes:525218 (525.2 KB) Interrupt:27 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:720 (720.0 B) TX bytes:720 (720.0 B) wifi0 Link encap:UNSPEC HWaddr 00-15-AF-CF-E2-CA-00-00-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3497 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:280 RX bytes:0 (0.0 B) TX bytes:179947 (179.9 KB) Interrupt:16 lshw -C network *-network description: Wireless interface product: AR5001 Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 logical name: wifi0 version: 01 serial: 00:15:af:cf:e2:ca width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix bus_master cap_list logical ethernet physical wireless configuration: broadcast=yes driver=ath_pci latency=0 multicast=yes wireless=IEEE 802.11g resources: irq:16 memory:fd7f0000-fd7fffff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 01 serial: 00:21:85:4d:82:78 size: 100MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.2.101 latency=0 link=yes multicast=yes port=MII speed=100MB/s resources: irq:27 ioport:c800(size=256) memory:fe2ff000-fe2fffff memory:fe2c0000-fe2dffff(prefetchable) lspci 00:00.0 Host bridge: ATI Technologies Inc RS690 Host Bridge 00:01.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (Internal gfx) 00:04.0 PCI bridge: ATI Technologies Inc Device 7914 00:06.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 2) 00:07.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 3) 00:12.0 SATA controller: ATI Technologies Inc SB600 Non-Raid-5 SATA 00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0) 00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1) 00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2) 00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3) 00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4) 00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI) 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 14) 00:14.1 IDE interface: ATI Technologies Inc SB600 IDE 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:05.0 VGA compatible controller: ATI Technologies Inc RS690M [Radeon X1200 Series] 01:05.2 Audio device: ATI Technologies Inc Radeon X1200 Series Audio Controller 02:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01) 05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) 06:04.0 CardBus bridge: O2 Micro, Inc. OZ711MP1/MS1 MemoryCardBus Controller (rev 21) 06:04.2 SD Host controller: O2 Micro, Inc. Integrated MMC/SD Controller (rev 01) 06:04.3 Bridge: O2 Micro, Inc. Integrated MS/xD Controller (rev 01) 06:04.4 FireWire (IEEE 1394): O2 Micro, Inc. Firewire (IEEE 1394) (rev 02) less /proc/modules | grep ath ath_rate_sample 11476 1 - Live 0xf812b000 ath_pci 193197 0 - Live 0xf85c3000 wlan 222892 5 wlan_wep,wlan_scan_sta,ath_rate_sample,ath_pci, Live 0xf8537000 ath_hal 398604 3 ath_rate_sample,ath_pci, Live 0xf8480000 I've been at this for hours now, also tried ndiswrapper and ath5k drivers with no luck, and really could use some help. Cheers.

  Read the article

• Nginx + Haproxy + Thin + Rails - 503 Service Unavailable -

  - by Luca G. Soave

  I don't know how troubleshoot this. I get "503 Service Unavailable" http error for all "nginx upstreams" proxy passing calls to haproxy fast_thin and slow_thin ( server 127.0.0.1:3100 and server 127.0.0.1:3200 ), which loadbalance on 6 Thin servers ( 127.0.0.1:3000 .. 3005 ). Static files like /blog are currently fine. The falldown is: nginx on port 80 - haproxy on 3100 and 3200 - thin on 3000 .. 3005 and then Rails. Here it is /etc/nginx/nginx.conf : user nginx; worker_processes 2; pid /var/run/nginx.pid; events { worker_connections 1024; } http { include /etc/nginx/mime.types; default_type application/octet-stream; log_format main '$remote_addr - $remote_user [$time_local] "$request" ' '$status $body_bytes_sent "$http_referer" ' '"$http_user_agent" "$http_x_forwarded_for"'; sendfile on; tcp_nopush on; keepalive_timeout 65; tcp_nodelay on; include /etc/nginx/conf.d/*.conf; } then /etc/nginx/conf.d/default.conf upstream fast_thin { server 127.0.0.1:3100; } upstream slow_thin { server 127.0.0.1:3200; } server { listen 80; server_name www.gitwatcher.com; rewrite ^/(.*) http://gitwatcher.com/$1 permanent; } server { listen 80; server_name gitwatcher.com; access_log /var/www/gitwatcher/log/access.log; error_log /var/www/gitwatcher/log/error.log; root /var/www/gitwatcher/public; # index index.html; location /about { proxy_pass http://fast_thin; break; } location /trends { proxy_pass http://slow_thin; break; } location /categories { proxy_pass http://slow_thin; break; } location /signout { proxy_pass http://slow_thin; break; } location /auth/github { proxy_pass http://slow_thin; break; } location / { proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $http_host; proxy_redirect off; if (-f $request_filename/index.html) { rewrite (.*) $1/index.html break; } if (-f $request_filename.html) { rewrite (.*) $1.html break; } if (!-f $request_filename) { proxy_pass http://slow_thin; break; } } } then haproxy config file /etc/haproxy/haproxy.cfg : global log 127.0.0.1 local0 log 127.0.0.1 local1 notice #log loghost local0 info maxconn 4096 #chroot /usr/share/haproxy user haproxy group haproxy daemon #debug #quiet nbproc 1 # number of processing cores defaults log global retries 3 maxconn 2000 contimeout 5000 mode http clitimeout 60000 # maximum inactivity time on the client side srvtimeout 30000 # maximum inactivity time on the server side timeout connect 4000 # maximum time to wait for a connection attempt to a server to succeed option httplog option dontlognull option redispatch option httpclose # disable keepalive (HAProxy does not yet support the HTTP keep-alive mode) option abortonclose # enable early dropping of aborted requests from pending queue option httpchk # enable HTTP protocol to check on servers health option forwardfor # enable insert of X-Forwarded-For headers balance roundrobin # each server is used in turns, according to assigned weight stats enable # enable web-stats at /haproxy?stats stats auth haproxy:pr0xystats # force HTTP Auth to view stats stats refresh 5s # refresh rate of stats page listen rails_proxy 127.0.0.1:3100 # - equal weights on all servers # - maxconn will queue requests at HAProxy if limit is reached # - minconn dynamically scales the connection concurrency (bound my maxconn) depending on size of HAProxy queue # - check health every 20000 microseconds server web1 127.0.0.1:3000 weight 1 minconn 3 maxconn 6 check inter 20000 server web1 127.0.0.1:3001 weight 1 minconn 3 maxconn 6 check inter 20000 server web1 127.0.0.1:3002 weight 1 minconn 3 maxconn 6 check inter 20000 listen slow_proxy 127.0.0.1:3200 # cluster for slow requests, lower the queues, check less frequently server slow1 127.0.0.1:3003 weight 1 minconn 1 maxconn 3 check inter 40000 server slow2 127.0.0.1:3004 weight 1 minconn 1 maxconn 3 check inter 40000 server slow3 127.0.0.1:3005 weight 1 minconn 1 maxconn 3 check inter 40000 and the Thin config file /etc/thin/gitwatcher.yml : --- chdir: /var/www/gitwatcher environment: production address: 0.0.0.0 port: 3000 timeout: 30 log: log/thin.log pid: tmp/pids/thin.pid max_conns: 1024 max_persistent_conns: 100 require: [] wait: 30 servers: 6 daemonize: true if I look into open listen ports, I got the following : root@fullness:/var/www/gitwatcher# lsof | grep TCP | egrep "nginx|haproxy|thin" nginx 834 root 8u IPv4 921 0t0 TCP *:http (LISTEN) nginx 835 nginx 8u IPv4 921 0t0 TCP *:http (LISTEN) nginx 837 nginx 8u IPv4 921 0t0 TCP *:http (LISTEN) haproxy 1908 haproxy 4u IPv4 11699 0t0 TCP localhost:3100 (LISTEN) haproxy 1908 haproxy 6u IPv4 11701 0t0 TCP localhost:3200 (LISTEN) root@fullness:/var/www/gitwatcher# iptables -L get me the following : Chain INPUT (policy DROP) target prot opt source destination ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED ACCEPT tcp -- anywhere anywhere tcp dpt:22222 ACCEPT tcp -- anywhere anywhere tcp dpt:http ACCEPT tcp -- anywhere anywhere tcp dpt:https ACCEPT all -- anywhere anywhere DROP all -- anywhere anywhere Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere Any help ?

  Read the article

• My linux server takes more than an hour to boot. Suggestions?

  - by jamieb

  I am building a CentOS 5.4 system that boots off a compact flash card using a card reader that emulates an IDE drive. It literally takes about an hour to boot. The ultra-slow part occurs when Grub is loading the kernel. Once that's done, the rest of the boot process only takes about a minute to get to a login prompt. Does anyone have any suggestions? I suspect that it may have to do with UDMA. Everything IDE-related in my BIOS seems to checkout. The read performance hdparm is telling me 1.77 MB/s. Ouch! (But even at that rate, it still shouldn't take an hour to decompress and load the kernel) [root@server ~]# hdparm -tT /dev/hdc /dev/hdc: Timing cached reads: 2444 MB in 2.00 seconds = 1222.04 MB/sec Timing buffered disk reads: 6 MB in 3.39 seconds = 1.77 MB/sec Trying to enable DMA is a no-go though: [root@server ~]# hdparm -d1 /dev/hdc /dev/hdc: setting using_dma to 1 (on) HDIO_SET_DMA failed: Operation not permitted using_dma = 0 (off) Here's some command outputs that might help: System [root@server ~]# uname -a Linux server.localdomain 2.6.18-164.el5xen #1 SMP Thu Sep 3 04:47:32 EDT 2009 i686 i686 i386 GNU/Linux PCI info: [root@server ~]# lspci -v 00:00.0 Host bridge: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub (rev 02) Subsystem: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub Flags: bus master, fast devsel, latency 0 Capabilities: [e0] Vendor Specific Information 00:02.0 VGA compatible controller: Intel Corporation 82945G/GZ Integrated Graphics Controller (rev 02) (prog-if 00 [VGA controller]) Subsystem: Intel Corporation 82945G/GZ Integrated Graphics Controller Flags: bus master, fast devsel, latency 0, IRQ 10 Memory at fdf00000 (32-bit, non-prefetchable) [size=512K] I/O ports at ff00 [size=8] Memory at d0000000 (32-bit, prefetchable) [size=256M] Memory at fdf80000 (32-bit, non-prefetchable) [size=256K] Capabilities: [90] Message Signalled Interrupts: 64bit- Queue=0/0 Enable- Capabilities: [d0] Power Management version 2 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 Flags: bus master, medium devsel, latency 0, IRQ 16 I/O ports at fe00 [size=32] 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 Flags: bus master, medium devsel, latency 0, IRQ 17 I/O ports at fd00 [size=32] 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 Flags: bus master, medium devsel, latency 0, IRQ 18 I/O ports at fc00 [size=32] 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 Flags: bus master, medium devsel, latency 0, IRQ 19 I/O ports at fb00 [size=32] 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01) (prog-if 20 [EHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller Flags: bus master, medium devsel, latency 0, IRQ 16 Memory at fdfff000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Capabilities: [58] Debug port 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) (prog-if 01 [Subtractive decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=32 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: fde00000-fdefffff Prefetchable memory behind bridge: 00000000fdd00000-00000000fdd00000 Capabilities: [50] #0d [0000] 00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01) Subsystem: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge Flags: bus master, medium devsel, latency 0 Capabilities: [e0] Vendor Specific Information 00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller (rev 01) (prog-if 80 [Master]) Subsystem: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 17 I/O ports at <unassigned> I/O ports at <unassigned> I/O ports at <unassigned> I/O ports at <unassigned> I/O ports at f800 [size=16] Capabilities: [70] Power Management version 2 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01) Subsystem: Intel Corporation 82801G (ICH7 Family) SMBus Controller Flags: medium devsel, IRQ 17 I/O ports at 0500 [size=32] 01:04.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ Flags: bus master, medium devsel, latency 32, IRQ 18 I/O ports at de00 [size=256] Memory at fdeff000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 01:06.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ Flags: bus master, medium devsel, latency 32, IRQ 17 I/O ports at dc00 [size=256] Memory at fdefe000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 01:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ Flags: bus master, medium devsel, latency 32, IRQ 19 I/O ports at da00 [size=256] Memory at fdefd000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 hdparm ouput: [root@server ~]# hdparm /dev/hdc /dev/hdc: multcount = 0 (off) IO_support = 0 (default 16-bit) unmaskirq = 0 (off) using_dma = 0 (off) keepsettings = 0 (off) readonly = 0 (off) readahead = 256 (on) geometry = 8146/16/63, sectors = 8211168, start = 0 [root@server ~]# hdparm -I /dev/hdc /dev/hdc: ATA device, with non-removable media Model Number: InnoDisk Corp. - iCF4000 4GB Serial Number: 20091023AACA70000753 Firmware Revision: 081107 Standards: Supported: 5 Likely used: 6 Configuration: Logical max current cylinders 8146 8146 heads 16 16 sectors/track 63 63 -- CHS current addressable sectors: 8211168 LBA user addressable sectors: 8211168 device size with M = 1024*1024: 4009 MBytes device size with M = 1000*1000: 4204 MBytes (4 GB) Capabilities: LBA, IORDY(can be disabled) Standby timer values: spec'd by Vendor R/W multiple sector transfer: Max = 2 Current = 2 DMA: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4 Cycle time: min=120ns recommended=120ns PIO: pio0 pio1 pio2 pio3 pio4 Cycle time: no flow control=120ns IORDY flow control=120ns Commands/features: Enabled Supported: * Power Management feature set * WRITE_BUFFER command * READ_BUFFER command * NOP cmd * CFA feature set * Mandatory FLUSH_CACHE HW reset results: CBLID- above Vih Device num = 0 CFA power mode 1: enabled and required by some commands Maximum current = 100ma Checksum: correct

  Read the article

• Xen DomU on DRBD device: barrier errors

  - by Halfgaar

  I'm testing setting up a Xen DomU with a DRBD storage for easy failover. Most of the time, immediatly after booting the DomU, I get an IO error: [ 3.153370] EXT3-fs (xvda2): using internal journal [ 3.277115] ip_tables: (C) 2000-2006 Netfilter Core Team [ 3.336014] nf_conntrack version 0.5.0 (3899 buckets, 15596 max) [ 3.515604] init: failsafe main process (397) killed by TERM signal [ 3.801589] blkfront: barrier: write xvda2 op failed [ 3.801597] blkfront: xvda2: barrier or flush: disabled [ 3.801611] end_request: I/O error, dev xvda2, sector 52171168 [ 3.801630] end_request: I/O error, dev xvda2, sector 52171168 [ 3.801642] Buffer I/O error on device xvda2, logical block 6521396 [ 3.801652] lost page write due to I/O error on xvda2 [ 3.801755] Aborting journal on device xvda2. [ 3.804415] EXT3-fs (xvda2): error: ext3_journal_start_sb: Detected aborted journal [ 3.804434] EXT3-fs (xvda2): error: remounting filesystem read-only [ 3.814754] journal commit I/O error [ 6.973831] init: udev-fallback-graphics main process (538) terminated with status 1 [ 6.992267] init: plymouth-splash main process (546) terminated with status 1 The manpage of drbdsetup says that LVM (which I use) doesn't support barriers (better known as tagged command queuing or native command queing), so I configured the drbd device not to use barriers. This can be seen in /proc/drbd (by "wo:f, meaning flush, the next method drbd chooses after barrier): 3: cs:Connected ro:Primary/Secondary ds:UpToDate/UpToDate C r---- ns:2160152 nr:520204 dw:2680344 dr:2678107 al:3549 bm:9183 lo:0 pe:0 ua:0 ap:0 ep:1 wo:f oos:0 And on the other host: 3: cs:Connected ro:Secondary/Primary ds:UpToDate/UpToDate C r---- ns:0 nr:2160152 dw:2160152 dr:0 al:0 bm:8052 lo:0 pe:0 ua:0 ap:0 ep:1 wo:f oos:0 I also enabled the option disable_sendpage, as per the drbd docs: cat /sys/module/drbd/parameters/disable_sendpage Y I also tried adding barriers=0 to fstab as mount option. Still it sometimes says: [ 58.603896] blkfront: barrier: write xvda2 op failed [ 58.603903] blkfront: xvda2: barrier or flush: disabled I don't even know if ext3 has a nobarrier option. And, because only one of my storage systems is battery backed, it would not be smart anyway. Why does it still compain about barriers when I disabled that? Both host are: Debian: 6.0.4 uname -a: Linux 2.6.32-5-xen-amd64 drbd: 8.3.7 Xen: 4.0.1 Guest: Ubuntu 12.04 LTS uname -a: Linux 3.2.0-24-generic pvops drbd resource: resource drbdvm { meta-disk internal; device /dev/drbd3; startup { # The timeout value when the last known state of the other side was available. 0 means infinite. wfc-timeout 0; # Timeout value when the last known state was disconnected. 0 means infinite. degr-wfc-timeout 180; } syncer { # This is recommended only for low-bandwidth lines, to only send those # blocks which really have changed. #csums-alg md5; # Set to about half your net speed rate 60M; # It seems that this option moved to the 'net' section in drbd 8.4. (later release than Debian has currently) verify-alg md5; } net { # The manpage says this is recommended only in pre-production (because of its performance), to determine # if your LAN card has a TCP checksum offloading bug. #data-integrity-alg md5; } disk { # Detach causes the device to work over-the-network-only after the # underlying disk fails. Detach is not default for historical reasons, but is # recommended by the docs. # However, the Debian defaults in drbd.conf suggest the machine will reboot in that event... on-io-error detach; # LVM doesn't support barriers, so disabling it. It will revert to flush. Check wo: in /proc/drbd. If you don't disable it, you get IO errors. no-disk-barrier; } on host1 { # universe is a VG disk /dev/universe/drbdvm-disk; address 10.0.0.1:7792; } on host2 { # universe is a VG disk /dev/universe/drbdvm-disk; address 10.0.0.2:7792; } } DomU cfg: bootloader = '/usr/lib/xen-default/bin/pygrub' vcpus = '2' memory = '512' # # Disk device(s). # root = '/dev/xvda2 ro' disk = [ 'phy:/dev/drbd3,xvda2,w', 'phy:/dev/universe/drbdvm-swap,xvda1,w', ] # # Hostname # name = 'drbdvm' # # Networking # # fake IP for posting vif = [ 'ip=1.2.3.4,mac=00:16:3E:22:A8:A7' ] # # Behaviour # on_poweroff = 'destroy' on_reboot = 'restart' on_crash = 'restart' In my test setup: the primary host's storage is 9650SE SATA-II RAID PCIe with battery. The secondary is software RAID1. Isn't DRBD+Xen widely used? With these problems, it's not going to work.

  Read the article

• vsftpd not allowing uploads. 550 response.

  - by Josh

  I've set vsftpd up on a centos box. I keep trying to upload files but I keep getting "550 Failed to change directory" and "550 Could not get file size." Here's my vsftpd.conf # The default compiled in settings are fairly paranoid. This sample file # loosens things up a bit, to make the ftp daemon more usable. # Please see vsftpd.conf.5 for all compiled in defaults. # # READ THIS: This example file is NOT an exhaustive list of vsftpd options. # Please read the vsftpd.conf.5 manual page to get a full idea of vsftpd's # capabilities. # # Allow anonymous FTP? (Beware - allowed by default if you comment this out). anonymous_enable=YES # # Uncomment this to allow local users to log in. local_enable=YES # # Uncomment this to enable any form of FTP write command. write_enable=YES # # Default umask for local users is 077. You may wish to change this to 022, # if your users expect that (022 is used by most other ftpd's) local_umask=022 # # Uncomment this to allow the anonymous FTP user to upload files. This only # has an effect if the above global write enable is activated. Also, you will # obviously need to create a directory writable by the FTP user. anon_upload_enable=YES # # Uncomment this if you want the anonymous FTP user to be able to create # new directories. anon_mkdir_write_enable=YES anon_other_write_enable=YES # # Activate directory messages - messages given to remote users when they # go into a certain directory. dirmessage_enable=YES # # The target log file can be vsftpd_log_file or xferlog_file. # This depends on setting xferlog_std_format parameter xferlog_enable=YES # # Make sure PORT transfer connections originate from port 20 (ftp-data). connect_from_port_20=YES # # If you want, you can arrange for uploaded anonymous files to be owned by # a different user. Note! Using "root" for uploaded files is not # recommended! #chown_uploads=YES #chown_username=whoever # # The name of log file when xferlog_enable=YES and xferlog_std_format=YES # WARNING - changing this filename affects /etc/logrotate.d/vsftpd.log #xferlog_file=/var/log/xferlog # # Switches between logging into vsftpd_log_file and xferlog_file files. # NO writes to vsftpd_log_file, YES to xferlog_file xferlog_std_format=NO # # You may change the default value for timing out an idle session. #idle_session_timeout=600 # # You may change the default value for timing out a data connection. #data_connection_timeout=120 # # It is recommended that you define on your system a unique user which the # ftp server can use as a totally isolated and unprivileged user. #nopriv_user=ftpsecure # # Enable this and the server will recognise asynchronous ABOR requests. Not # recommended for security (the code is non-trivial). Not enabling it, # however, may confuse older FTP clients. #async_abor_enable=YES # # By default the server will pretend to allow ASCII mode but in fact ignore # the request. Turn on the below options to have the server actually do ASCII # mangling on files when in ASCII mode. # Beware that on some FTP servers, ASCII support allows a denial of service # attack (DoS) via the command "SIZE /big/file" in ASCII mode. vsftpd # predicted this attack and has always been safe, reporting the size of the # raw file. # ASCII mangling is a horrible feature of the protocol. #ascii_upload_enable=YES #ascii_download_enable=YES # # You may fully customise the login banner string: #ftpd_banner=Welcome to blah FTP service. # # You may specify a file of disallowed anonymous e-mail addresses. Apparently # useful for combatting certain DoS attacks. #deny_email_enable=YES # (default follows) #banned_email_file=/etc/vsftpd/banned_emails # # You may specify an explicit list of local users to chroot() to their home # directory. If chroot_local_user is YES, then this list becomes a list of # users to NOT chroot(). #chroot_list_enable=YES # (default follows) #chroot_list_file=/etc/vsftpd/chroot_list # # You may activate the "-R" option to the builtin ls. This is disabled by # default to avoid remote users being able to cause excessive I/O on large # sites. However, some broken FTP clients such as "ncftp" and "mirror" assume # the presence of the "-R" option, so there is a strong case for enabling it. #ls_recurse_enable=YES # # When "listen" directive is enabled, vsftpd runs in standalone mode and # listens on IPv4 sockets. This directive cannot be used in conjunction # with the listen_ipv6 directive. listen=YES # This directive enables listening on IPv6 sockets. To listen on IPv4 and IPv6 # sockets, you must run two copies of vsftpd whith two configuration files. # Make sure, that one of the listen options is commented !! #listen_ipv6=YES pam_service_name=vsftpd userlist_enable=YES tcp_wrappers=YES log_ftp_protocol=YES banner_file=/etc/vsftpd/issue local_root=/var/www guest_enable=YES guest_username=ftpusr ftp_username=nobody

  Read the article

• nginx+php-fpm help optimize configs

  - by Dmitro

  I have 3 servers. First server (CPU - model name: 06/17, 2.66GHz, 4 cores, 8GB RAM) have nginx as load balancer with next config upstream lb_mydomain { server mydomain.ru:81 weight=2; server 66.0.0.18 weight=6; } server { listen 80; server_name ~(?!mydomain.ru)(.*); client_max_body_size 20m; location / { proxy_pass http://lb_mydomain; proxy_redirect off; proxy_set_header Connection close; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_pass_header Set-Cookie; proxy_pass_header P3P; proxy_pass_header Content-Type; proxy_pass_header Content-Disposition; proxy_pass_header Content-Length; } } And configs from nginx.conf: user www-data; worker_processes 5; # worker_priority -1; error_log /var/log/nginx/error.log; pid /var/run/nginx.pid; events { worker_connections 5024; # multi_accept on; } http { include /etc/nginx/mime.types; access_log /var/log/nginx/access.log; sendfile on; default_type application/octet-stream; #tcp_nopush on; keepalive_timeout 65; tcp_nodelay on; gzip on; gzip_disable "MSIE [1-6]\.(?!.*SV1)"; # PHP-FPM (backend) upstream php-fpm { server 127.0.0.1:9000; } include /etc/nginx/conf.d/*.conf; include /etc/nginx/sites-enabled/*; } And config php-fpm: listen = 127.0.0.1:9000 ;listen.backlog = -1 ;listen.allowed_clients = 127.0.0.1 ;listen.owner = www-data ;listen.group = www-data ;listen.mode = 0666 user = www-data group = www-data pm = dynamic pm.max_children = 80 ;pm.start_servers = 20 pm.min_spare_servers = 5 pm.max_spare_servers = 35 ;pm.max_requests = 500 pm.status_path = /status ping.path = /ping ;ping.response = pong request_terminate_timeout = 30s request_slowlog_timeout = 10s slowlog = /var/log/php-fpm.log.slow ;rlimit_files = 1024 ;rlimit_core = 0 ;chroot = chdir = /var/www ;catch_workers_output = yes ;env[HOSTNAME] = $HOSTNAME ;env[PATH] = /usr/local/bin:/usr/bin:/bin ;env[TMP] = /tmp ;env[TMPDIR] = /tmp ;env[TEMP] = /tmp ;php_admin_value[sendmail_path] = /usr/sbin/sendmail -t -i -f [email protected] ;php_flag[display_errors] = off ;php_admin_value[error_log] = /var/log/fpm-php.www.log ;php_admin_flag[log_errors] = on ;php_admin_value[memory_limit] = 32M In top I see 20 php-fpm processes which use from 1% - 15% CPU. So it's have high load averadge: top - 15:36:22 up 34 days, 20:54, 1 user, load average: 5.98, 7.75, 8.78 Tasks: 218 total, 1 running, 217 sleeping, 0 stopped, 0 zombie Cpu(s): 34.1%us, 3.2%sy, 0.0%ni, 37.0%id, 24.8%wa, 0.0%hi, 0.9%si, 0.0%st Mem: 8183228k total, 7538584k used, 644644k free, 351136k buffers Swap: 9936892k total, 14636k used, 9922256k free, 990540k cached Second server(CPU - model name: Intel(R) Xeon(R) CPU E5504 @ 2.00GHz, 8 cores, 8GB RAM). Nginx configs from nginx.conf: user www-data; worker_processes 5; # worker_priority -1; error_log /var/log/nginx/error.log; pid /var/run/nginx.pid; events { worker_connections 5024; # multi_accept on; } http { include /etc/nginx/mime.types; access_log /var/log/nginx/access.log; sendfile on; default_type application/octet-stream; #tcp_nopush on; keepalive_timeout 65; tcp_nodelay on; gzip on; gzip_disable "MSIE [1-6]\.(?!.*SV1)"; # PHP-FPM (backend) upstream php-fpm { server 127.0.0.1:9000; } include /etc/nginx/conf.d/*.conf; include /etc/nginx/sites-enabled/*; } And config of php-fpm: listen = 127.0.0.1:9000 ;listen.backlog = -1 ;listen.allowed_clients = 127.0.0.1 ;listen.owner = www-data ;listen.group = www-data ;listen.mode = 0666 user = www-data group = www-data pm = dynamic pm.max_children = 50 ;pm.start_servers = 20 pm.min_spare_servers = 5 pm.max_spare_servers = 35 ;pm.max_requests = 500 ;pm.status_path = /status ;ping.path = /ping ;ping.response = pong ;request_terminate_timeout = 0 ;request_slowlog_timeout = 0 ;slowlog = /var/log/php-fpm.log.slow ;rlimit_files = 1024 ;rlimit_core = 0 ;chroot = chdir = /var/www ;catch_workers_output = yes ;env[HOSTNAME] = $HOSTNAME ;env[PATH] = /usr/local/bin:/usr/bin:/bin ;env[TMP] = /tmp ;env[TMPDIR] = /tmp ;env[TEMP] = /tmp ;php_admin_value[sendmail_path] = /usr/sbin/sendmail -t -i -f [email protected] ;php_flag[display_errors] = off ;php_admin_value[error_log] = /var/log/fpm-php.www.log ;php_admin_flag[log_errors] = on ;php_admin_value[memory_limit] = 32M In top I see 50 php-fpm processes which use from 10% - 25% CPU. So it's have high load averadge: top - 15:53:05 up 33 days, 1:15, 1 user, load average: 41.35, 40.28, 39.61 Tasks: 239 total, 40 running, 199 sleeping, 0 stopped, 0 zombie Cpu(s): 96.5%us, 3.1%sy, 0.0%ni, 0.0%id, 0.0%wa, 0.0%hi, 0.4%si, 0.0%st Mem: 8185560k total, 7804224k used, 381336k free, 161648k buffers Swap: 19802108k total, 16k used, 19802092k free, 5068112k cached Third server is server with database postgresql. Also i try ab -n 50 -c 5 http://www.mydomain.ru/ And I get next info: Complete requests: 50 Failed requests: 48 (Connect: 0, Receive: 0, Length: 48, Exceptions: 0) Write errors: 0 Total transferred: 9271367 bytes HTML transferred: 9247767 bytes Requests per second: 1.02 [#/sec] (mean) Time per request: 4882.427 [ms] (mean) Time per request: 976.486 [ms] (mean, across all concurrent requests) Transfer rate: 185.44 [Kbytes/sec] received Please advise how can I make lower level of load average?

  Read the article

• Cisco ASA 5505 - L2TP over IPsec

  - by xraminx

  I have followed this document on cisco site to set up the L2TP over IPsec connection. When I try to establish a VPN to ASA 5505 from my Windows XP, after I click on "connect" button, the "Connecting ...." dialog box appears and after a while I get this error message: Error 800: Unable to establish VPN connection. The VPN server may be unreachable, or security parameters may not be configured properly for this connection. ASA version 7.2(4) ASDM version 5.2(4) Windows XP SP3 Windows XP and ASA 5505 are on the same LAN for test purposes. Edit 1: There are two VLANs defined on the cisco device (the standard setup on cisco ASA5505). - port 0 is on VLAN2, outside; - and ports 1 to 7 on VLAN1, inside. I run a cable from my linksys home router (10.50.10.1) to the cisco ASA5505 router on port 0 (outside). Port 0 have IP 192.168.1.1 used internally by cisco and I have also assigned the external IP 10.50.10.206 to port 0 (outside). I run a cable from Windows XP to Cisco router on port 1 (inside). Port 1 is assigned an IP from Cisco router 192.168.1.2. The Windows XP is also connected to my linksys home router via wireless (10.50.10.141). Edit 2: When I try to establish vpn, the Cisco device real time Log viewer shows 7 entries like this: Severity:5 Date:Sep 15 2009 Time: 14:51:29 SyslogID: 713904 Destination IP = 10.50.10.141, Decription: No crypto map bound to interface... dropping pkt Edit 3: This is the setup on the router right now. Result of the command: "show run" : Saved : ASA Version 7.2(4) ! hostname ciscoasa domain-name default.domain.invalid enable password HGFHGFGHFHGHGFHGF encrypted passwd NMMNMNMNMNMNMN encrypted names name 192.168.1.200 WebServer1 name 10.50.10.206 external-ip-address ! interface Vlan1 nameif inside security-level 100 ip address 192.168.1.1 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address external-ip-address 255.0.0.0 ! interface Vlan3 no nameif security-level 50 no ip address ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! ftp mode passive dns server-group DefaultDNS domain-name default.domain.invalid object-group service l2tp udp port-object eq 1701 access-list outside_access_in remark Allow incoming tcp/http access-list outside_access_in extended permit tcp any host WebServer1 eq www access-list outside_access_in extended permit udp any any eq 1701 access-list inside_nat0_outbound extended permit ip any 192.168.1.208 255.255.255.240 access-list inside_cryptomap_1 extended permit ip interface outside interface inside pager lines 24 logging enable logging asdm informational mtu inside 1500 mtu outside 1500 ip local pool PPTP-VPN 192.168.1.210-192.168.1.220 mask 255.255.255.0 icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-524.bin no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface www WebServer1 www netmask 255.255.255.255 access-group outside_access_in in interface outside timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute http server enable http 192.168.1.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac crypto ipsec transform-set TRANS_ESP_3DES_SHA mode transport crypto ipsec transform-set TRANS_ESP_3DES_MD5 esp-3des esp-md5-hmac crypto ipsec transform-set TRANS_ESP_3DES_MD5 mode transport crypto map outside_map 1 match address inside_cryptomap_1 crypto map outside_map 1 set transform-set TRANS_ESP_3DES_MD5 crypto map outside_map interface inside crypto isakmp enable outside crypto isakmp policy 10 authentication pre-share encryption 3des hash md5 group 2 lifetime 86400 telnet timeout 5 ssh timeout 5 console timeout 0 dhcpd auto_config outside ! dhcpd address 192.168.1.2-192.168.1.33 inside dhcpd enable inside ! group-policy DefaultRAGroup internal group-policy DefaultRAGroup attributes dns-server value 192.168.1.1 vpn-tunnel-protocol IPSec l2tp-ipsec username myusername password FGHFGHFHGFHGFGFHF nt-encrypted tunnel-group DefaultRAGroup general-attributes address-pool PPTP-VPN default-group-policy DefaultRAGroup tunnel-group DefaultRAGroup ipsec-attributes pre-shared-key * tunnel-group DefaultRAGroup ppp-attributes no authentication chap authentication ms-chap-v2 ! ! prompt hostname context Cryptochecksum:a9331e84064f27e6220a8667bf5076c1 : end

  Read the article

• Set up linux box for hosting a-z

  - by microchasm

  I am in the process of reinstalling the OS on a machine that will be used to host a couple of apps for our business. The apps will be local only; access from external clients will be via vpn only. The prior setup used a hosting control panel (Plesk) for most of the admin, and I was looking at using another similar piece of software for the reinstall - but I figured I should finally learn how it all works. I can do most of the things the software would do for me, but am unclear on the symbiosis of it all. This is all an attempt to further distance myself from the land of Configuration Programmer/Programmer, if at all possible. I can't find a full walkthrough anywhere for what I'm looking for, so I thought I'd put up this question, and if people can help me on the way I will edit this with the answers, and document my progress/pitfalls. Hopefully someday this will help someone down the line. The details: CentOS 5.5 x86_64 httpd: Apache/2.2.3 mysql: 5.0.77 (to be upgraded) php: 5.1 (to be upgraded) The requirements: SECURITY!! Secure file transfer Secure client access (SSL Certs and CA) Secure data storage Virtualhosts/multiple subdomains Local email would be nice, but not critical The Steps: Download latest CentOS DVD-iso (torrent worked great for me). Install CentOS: While going through the install, I checked the Server Components option thinking I was going to be using another Plesk-like admin. In hindsight, considering I've decided to try to go my own way, this probably wasn't the best idea. Basic config: Setup users, networking/ip address etc. Yum update/upgrade. Upgrade PHP/MySQL: To upgrade PHP and MySQL to the latest versions, I had to look to another repo outside CentOS. IUS looks great and I'm happy I found it! Add IUS repository to our package manager cd /tmp wget http://dl.iuscommunity.org/pub/ius/stable/Redhat/5/x86_64/epel-release-1-1.ius.el5.noarch.rpm rpm -Uvh epel-release-1-1.ius.el5.noarch.rpm wget http://dl.iuscommunity.org/pub/ius/stable/Redhat/5/x86_64/ius-release-1-4.ius.el5.noarch.rpm rpm -Uvh ius-release-1-4.ius.el5.noarch.rpm yum list | grep -w \.ius\. # list all the packages in the IUS repository; use this to find PHP/MySQL version and libraries you want to install Remove old version of PHP and install newer version from IUS rpm -qa | grep php # to list all of the installed php packages we want to remove yum shell # open an interactive yum shell remove php-common php-mysql php-cli #remove installed PHP components install php53 php53-mysql php53-cli php53-common #add packages you want transaction solve #important!! checks for dependencies transaction run #important!! does the actual installation of packages. [control+d] #exit yum shell php -v PHP 5.3.2 (cli) (built: Apr 6 2010 18:13:45) Upgrade MySQL from IUS repository /etc/init.d/mysqld stop rpm -qa | grep mysql # to see installed mysql packages yum shell remove mysql mysql-server #remove installed MySQL components install mysql51 mysql51-server mysql51-devel transaction solve #important!! checks for dependencies transaction run #important!! does the actual installation of packages. [control+d] #exit yum shell service mysqld start mysql -v Server version: 5.1.42-ius Distributed by The IUS Community Project Upgrade instructions courtesy of IUS wiki: http://wiki.iuscommunity.org/Doc/ClientUsageGuide Install rssh (restricted shell) to provide scp and sftp access, without allowing ssh login cd /tmp wget http://dag.wieers.com/rpm/packages/rssh/rssh-2.3.2-1.2.el5.rf.x86_64.rpm rpm -ivh rssh-2.3.2-1.2.el5.rf.x86_64.rpm useradd -m -d /home/dev -s /usr/bin/rssh dev passwd dev Edit /etc/rssh.conf to grant access to SFTP to rssh users. vi /etc/rssh.conf Uncomment or add: allowscp allowsftp This allows me to connect to the machine via SFTP protocol in Transmit (my FTP program of choice; I'm sure it's similar with other FTP apps). rssh instructions appropriated (with appreciation!) from http://www.cyberciti.biz/tips/linux-unix-restrict-shell-access-with-rssh.html Set up virtual interfaces ifconfig eth1:1 192.168.1.3 up #start up the virtual interface cd /etc/sysconfig/network-scripts/ cp ifcfg-eth1 ifcfg-eth1:1 #copy default script and match name to our virtual interface vi ifcfg-eth1:1 #modify eth1:1 script #ifcfg-eth1:1 | modify so it looks like this: DEVICE=eth1:1 IPADDR=192.168.1.3 NETMASK=255.255.255.0 NETWORK=192.168.1.0 ONBOOT=yes NAME=eth1:1 Add more Virtual interfaces as needed by repeating. Because of the ONBOOT=yes line in the ifcfg-eth1:1 file, this interface will be brought up when the system boots, or the network starts/restarts. service network restart Shutting down interface eth0: [ OK ] Shutting down interface eth1: [ OK ] Shutting down loopback interface: [ OK ] Bringing up loopback interface: [ OK ] Bringing up interface eth0: [ OK ] Bringing up interface eth1: [ OK ] ping 192.168.1.3 64 bytes from 192.168.1.3: icmp_seq=1 ttl=64 time=0.105 ms And this is where I'm at. I will keep editing this as I make progress. Any tips on how to Configure virtual interfaces/ip based virtual hosts for SSL, setting up a CA, or anything else would be appreciated.

  Read the article

• help setting up an IPSEC vpn from my linux box

  - by robthewolf

  I have an office with a router and a remote server (Linux - Ubuntu 10.10). Both locations need to connect to a data supplier through a VPN. The VPN is an IPSEC gateway. I was able to configure my Linksys rv42 router to create a VPN connection successfully and now I need to do the same for Linux server. I have been messing around with this for too long. First I tried OpenVPN, but that is SSL and not IPSEC. Then I tried Shrew. I think I have the settings correct but I haven't been able to create the connection. It maybe that I have to use something else like a direct IPSEC config or something like that. If someone knows of a way to turn the following settings that I have been given below into a working IPSEC VPN connection I would be very grateful. Here are the settings I was given that must be used to connect to my supplier: Local destination network: 192.168.4.0/24 Local destination hosts: 192.168.4.100 Remote destination network: 192.167.40.0/24 Remote destination hosts: 192.168.40.27 VPN peering point: xxx.xxx.xxx.xxx Then they have given me the following details: IPSEC/ISAKMP Phase 1 Parameters: Authentication method: pre shared secret Diffie Hellman group: group 2 Encryption Algorithm: 3DES Lifetime in seconds:28800 Phase 2 parameters: IPSEC security: ESP Encryption algortims: 3DES Authentication algorithms: MD5 lifetime in seconds: 28800 pfs: disabled Here are the settings from my attempt to use shrew: n:version:2 n:network-ike-port:500 n:network-mtu-size:1380 n:client-addr-auto:0 n:network-frag-size:540 n:network-dpd-enable:1 n:network-notify-enable:1 n:client-banner-enable:1 n:client-dns-used:1 b:auth-mutual-psk:YjJzN2QzdDhyN2EyZDNpNG42ZzQ= n:phase1-dhgroup:2 n:phase1-keylen:0 n:phase1-life-secs:28800 n:phase1-life-kbytes:0 n:vendor-chkpt-enable:0 n:phase2-keylen:0 n:phase2-pfsgroup:-1 n:phase2-life-secs:28800 n:phase2-life-kbytes:0 n:policy-nailed:0 n:policy-list-auto:1 n:client-dns-auto:1 n:network-natt-port:4500 n:network-natt-rate:15 s:client-dns-addr:0.0.0.0 s:client-dns-suffix: s:network-host:xxx.xxx.xxx.xxx s:client-auto-mode:pull s:client-iface:virtual s:client-ip-addr:192.168.4.0 s:client-ip-mask:255.255.255.0 s:network-natt-mode:enable s:network-frag-mode:disable s:auth-method:mutual-psk s:ident-client-type:address s:ident-client-data:192.168.4.0 s:ident-server-type:address s:ident-server-data:192.168.40.0 s:phase1-exchange:aggressive s:phase1-cipher:3des s:phase1-hash:md5 s:phase2-transform:3des s:phase2-hmac:md5 s:ipcomp-transform:disabled Finally here is the debug output from the shrew log: 10/12/22 17:22:18 ii : ipc client process thread begin ... 10/12/22 17:22:18 < A : peer config add message 10/12/22 17:22:18 DB : peer added ( obj count = 1 ) 10/12/22 17:22:18 ii : local address 217.xxx.xxx.xxx selected for peer 10/12/22 17:22:18 DB : tunnel added ( obj count = 1 ) 10/12/22 17:22:18 < A : proposal config message 10/12/22 17:22:18 < A : proposal config message 10/12/22 17:22:18 < A : client config message 10/12/22 17:22:18 < A : local id '192.168.4.0' message 10/12/22 17:22:18 < A : remote id '192.168.40.0' message 10/12/22 17:22:18 < A : preshared key message 10/12/22 17:22:18 < A : peer tunnel enable message 10/12/22 17:22:18 DB : new phase1 ( ISAKMP initiator ) 10/12/22 17:22:18 DB : exchange type is aggressive 10/12/22 17:22:18 DB : 217.xxx.xxx.xxx:500 <- 206.xxx.xxx.xxx:500 10/12/22 17:22:18 DB : c1a8b31ac860995d:0000000000000000 10/12/22 17:22:18 DB : phase1 added ( obj count = 1 ) 10/12/22 17:22:18 : security association payload 10/12/22 17:22:18 : - proposal #1 payload 10/12/22 17:22:18 : -- transform #1 payload 10/12/22 17:22:18 : key exchange payload 10/12/22 17:22:18 : nonce payload 10/12/22 17:22:18 : identification payload 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v00 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v01 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v02 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v03 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( rfc ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports DPDv1 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is SHREW SOFT compatible 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is NETSCREEN compatible 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is SIDEWINDER compatible 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is CISCO UNITY compatible 10/12/22 17:22:18 = : cookies c1a8b31ac860995d:0000000000000000 10/12/22 17:22:18 = : message 00000000 10/12/22 17:22:18 - : send IKE packet 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 ( 484 bytes ) 10/12/22 17:22:18 DB : phase1 resend event scheduled ( ref count = 2 ) 10/12/22 17:22:18 ii : opened tap device tap0 10/12/22 17:22:28 - : resend 1 phase1 packet(s) 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 10/12/22 17:22:38 - : resend 1 phase1 packet(s) 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 10/12/22 17:22:48 - : resend 1 phase1 packet(s) 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 10/12/22 17:22:58 ii : resend limit exceeded for phase1 exchange 10/12/22 17:22:58 ii : phase1 removal before expire time 10/12/22 17:22:58 DB : phase1 deleted ( obj count = 0 ) 10/12/22 17:22:58 ii : closed tap device tap0 10/12/22 17:22:58 DB : tunnel stats event canceled ( ref count = 1 ) 10/12/22 17:22:58 DB : removing tunnel config references 10/12/22 17:22:58 DB : removing tunnel phase2 references 10/12/22 17:22:58 DB : removing tunnel phase1 references 10/12/22 17:22:58 DB : tunnel deleted ( obj count = 0 ) 10/12/22 17:22:58 DB : removing all peer tunnel refrences 10/12/22 17:22:58 DB : peer deleted ( obj count = 0 ) 10/12/22 17:22:58 ii : ipc client process thread exit ...

  Read the article

• Server hung with "blocked for more than 120 seconds", diskless

  - by alterpub

  I have server which hung every 2-5 days. dmesg show following situation: kernel: [490894.231753] INFO: task munin-html:10187 blocked for more than 120 seconds. kernel: [490894.231799] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. kernel: [490894.231843] munin-html D 0000000000000000 0 10187 9796 0x00000000 kernel: [490894.231878] ffff88063174b968 0000000000000082 ffff88063174b8d8 0000000000015b80 kernel: [490894.231930] ffff88063174bfd8 0000000000015b80 ffff88063174bfd8 ffff88062fe644d0 kernel: [490894.231982] 0000000000015b80 0000000000015b80 ffff88063174bfd8 0000000000015b80 kernel: [490894.232033] Call Trace: kernel: [490894.232059] [<ffffffff8117fce0>] ? sync_buffer+0x0/0x50 kernel: [490894.232089] [<ffffffff815a1f13>] io_schedule+0x73/0xc0 kernel: [490894.232115] [<ffffffff8117fd25>] sync_buffer+0x45/0x50 kernel: [490894.232143] [<ffffffff815a258f>] __wait_on_bit+0x5f/0x90 kernel: [490894.232170] [<ffffffff8117fce0>] ? sync_buffer+0x0/0x50 kernel: [490894.232197] [<ffffffff815a2638>] out_of_line_wait_on_bit+0x78/0x90 kernel: [490894.232227] [<ffffffff81080250>] ? wake_bit_function+0x0/0x40 kernel: [490894.232255] [<ffffffff8117fcd6>] __wait_on_buffer+0x26/0x30 kernel: [490894.232288] [<ffffffffa00131be>] squashfs_read_data+0x1be/0x520 [squashfs] kernel: [490894.232320] [<ffffffff8114f0f1>] ? __mem_cgroup_try_charge+0x71/0x450 kernel: [490894.232350] [<ffffffffa0013963>] squashfs_cache_get+0x1c3/0x320 [squashfs] kernel: [490894.232381] [<ffffffffa00136eb>] ? squashfs_copy_data+0x10b/0x130 [squashfs] kernel: [490894.232426] [<ffffffff815a3dbe>] ? _raw_spin_lock+0xe/0x20 kernel: [490894.232454] [<ffffffffa0013b68>] ? squashfs_read_metadata+0x48/0xf0 [squashfs] kernel: [490894.232499] [<ffffffffa0013ae1>] squashfs_get_datablock+0x21/0x30 [squashfs] kernel: [490894.232544] [<ffffffffa0015026>] squashfs_readpage+0x436/0x4a0 [squashfs] kernel: [490894.232575] [<ffffffff8111a375>] ? __inc_zone_page_state+0x35/0x40 kernel: [490894.232606] [<ffffffff8110d072>] __do_page_cache_readahead+0x172/0x210 kernel: [490894.232636] [<ffffffff8110d131>] ra_submit+0x21/0x30 kernel: [490894.232662] [<ffffffff811045f3>] filemap_fault+0x3f3/0x450 kernel: [490894.232691] [<ffffffff812bd156>] ? prio_tree_insert+0x256/0x2b0 kernel: [490894.232726] [<ffffffffa009225d>] aufs_fault+0x11d/0x170 [aufs] kernel: [490894.232755] [<ffffffff8111f6d4>] __do_fault+0x54/0x560 kernel: [490894.232782] [<ffffffff81122f39>] handle_mm_fault+0x1b9/0x440 kernel: [490894.232811] [<ffffffff811286f5>] ? do_mmap_pgoff+0x335/0x380 kernel: [490894.232840] [<ffffffff815a7af5>] do_page_fault+0x125/0x350 kernel: [490894.232867] [<ffffffff815a4675>] page_fault+0x25/0x30 Os info cat /etc/issue.net Ubuntu 10.04.2 LTS uname -a Linux Shard1Host3 2.6.35-32-server #68~lucid1-Ubuntu SMP Wed Mar 28 18:33:00 UTC 2012 x86_64 GNU/Linux This system load via ltsp and hasn't harddrives also it has a lot of memory 24Gb. free -m total used free shared buffers cached Mem: 24152 17090 7061 0 50 494 -/+ buffers/cache: 16545 7607 Swap: 0 0 0 I put vmstat info here but I think it won't give results after reboot vmstat 1 30 procs -----------memory---------- ---swap-- -----io---- -system-- ----cpu---- r b swpd free buff cache si so bi bo in cs us sy id wa 0 0 0 7231156 52196 506400 0 0 0 0 172 143 7 0 92 0 1 0 0 7231024 52196 506400 0 0 0 0 7859 16233 5 0 94 0 0 0 0 7231024 52196 506400 0 0 0 0 7870 16446 2 0 98 0 0 0 0 7230900 52196 506400 0 0 0 0 7308 15661 5 0 95 0 0 0 0 7231100 52196 506400 0 0 0 0 7960 16543 6 0 94 0 0 0 0 7231100 52196 506400 0 0 0 0 7542 16047 5 1 94 0 3 0 0 7231100 52196 506400 0 0 0 0 7709 16621 3 0 96 0 0 0 0 7231220 52196 506400 0 0 0 0 7857 16552 4 0 96 0 0 0 0 7231220 52196 506400 0 0 0 0 7192 15491 6 0 94 0 0 0 0 7231220 52196 506400 0 0 0 0 7423 15792 5 1 94 0 1 0 0 7231260 52196 506404 0 0 0 0 7686 16296 2 0 98 0 0 0 0 7231260 52196 506404 0 0 0 0 6976 15183 5 0 95 0 0 0 0 7231260 52196 506404 0 0 0 0 7303 15600 4 0 95 0 0 0 0 7231320 52196 506404 0 0 0 0 7967 16241 1 0 98 0 0 0 0 7231444 52196 506404 0 0 0 0 6948 15113 6 0 94 0 0 0 0 7231444 52196 506404 0 0 0 0 7931 16181 6 0 94 0 1 0 0 7231516 52196 506404 0 0 0 0 7715 15829 6 0 94 0 0 0 0 7231516 52196 506404 0 0 0 0 7771 16036 2 0 97 0 0 0 0 7231268 52196 506404 0 0 0 0 7782 16202 6 0 94 0 1 0 0 7231212 52196 506404 0 0 0 0 7457 15622 4 0 96 0 0 0 0 7231212 52196 506404 0 0 0 0 7573 16045 2 0 98 0 2 0 0 7231216 52196 506404 0 0 0 0 7689 16076 6 0 94 0 0 0 0 7231424 52196 506404 0 0 0 0 7429 15650 4 0 95 0 3 0 0 7231424 52196 506404 0 0 0 0 7534 16168 3 0 97 0 1 0 0 7230548 52196 506404 0 0 0 0 8559 15926 7 1 92 0 0 0 0 7230672 52196 506404 0 0 0 0 7720 15905 2 0 98 0 0 0 0 7230548 52196 506404 0 0 0 0 7677 16313 5 0 95 0 1 0 0 7230676 52196 506404 0 0 0 0 7209 15432 5 0 95 0 0 0 0 7230800 52196 506404 0 0 0 0 7522 15861 2 0 98 0 0 0 0 7230552 52196 506404 0 0 0 0 7760 16661 5 0 95 0 In the munin(monitoring system) graphs I see(before server hung): Disk(nbd0) IOs per device: read: 289m but avg by week 2.09m Disk(nbd0) throughput per device: read: 4.73k but avg by week 108.76 Disk(nbd0) utilization per device: 100% but avg by week 1.2% Eth0 traffic was low: in/out only 2Mbps Number of threads increased to 566 usually 392 Fork rate 1.08 but usually 2.82 VMStat(processes state) Increased to 17.77(from 0 as far as I could see in the graph) CPU usage iowait 880.46% when usually 6.67% It'll be great if somebody help me to understand what's up.

  Read the article

• Can't access shared drive when connecting over VPN

  - by evolvd

  I can ping all network devices but it doesn't seem that DNS is resolving their hostnames. ipconfig/ all is showing that I am pointing to the correct dns server. I can "ping "dnsname"" and it will resolve but it wont resolve any other names. Split tunnel is set up so outside DNS is resolving fine So one issue might be DNS but I have the IP address of the server share so I figure I could just get to it that way. example: \10.0.0.1\ well I can't get to it that way either and I get "the specified network name is no longer available" I can ping it but I can't open the share. Below is the ASA config : ASA Version 8.2(1) ! hostname KG-ASA domain-name example.com names ! interface Vlan1 nameif inside security-level 100 ip address 10.0.0.253 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address dhcp setroute ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! ftp mode passive clock timezone EST -5 clock summer-time EDT recurring dns domain-lookup outside dns server-group DefaultDNS name-server 10.0.0.101 domain-name blah.com access-list OUTSIDE_IN extended permit tcp any host 10.0.0.253 eq 10000 access-list OUTSIDE_IN extended permit tcp any host 10.0.0.253 eq 8333 access-list OUTSIDE_IN extended permit tcp any host 10.0.0.253 eq 902 access-list SPLIT-TUNNEL-VPN standard permit 10.0.0.0 255.0.0.0 access-list NONAT extended permit ip 10.0.0.0 255.255.255.0 10.0.1.0 255.255.255.0 pager lines 24 logging asdm informational mtu inside 1500 mtu outside 1500 ip local pool IPSECVPN-POOL 10.0.1.2-10.0.1.50 mask 255.255.255.0 icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-621.bin no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list NONAT nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface 10000 10.0.0.101 10000 netmask 255.255.255.255 static (inside,outside) tcp interface 8333 10.0.0.101 8333 netmask 255.255.255.255 static (inside,outside) tcp interface 902 10.0.0.101 902 netmask 255.255.255.255 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy aaa authentication enable console LOCAL aaa authentication http console LOCAL aaa authentication serial console LOCAL aaa authentication ssh console LOCAL aaa authentication telnet console LOCAL http server enable http 10.0.0.0 255.255.0.0 inside http 0.0.0.0 0.0.0.0 outside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set myset esp-aes esp-sha-hmac crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map dynmap 1 set transform-set myset crypto dynamic-map dynmap 1 set reverse-route crypto map IPSEC-MAP 65535 ipsec-isakmp dynamic dynmap crypto map IPSEC-MAP interface outside crypto isakmp enable outside crypto isakmp policy 10 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 crypto isakmp policy 65535 authentication pre-share encryption aes hash sha group 2 lifetime 86400 telnet 0.0.0.0 0.0.0.0 inside telnet timeout 5 ssh 0.0.0.0 0.0.0.0 inside ssh 70.60.228.0 255.255.255.0 outside ssh 74.102.150.0 255.255.254.0 outside ssh 74.122.164.0 255.255.252.0 outside ssh timeout 5 console timeout 0 dhcpd dns 10.0.0.101 dhcpd lease 7200 dhcpd domain blah.com ! dhcpd address 10.0.0.110-10.0.0.170 inside dhcpd enable inside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept ntp server 63.111.165.21 webvpn enable outside svc image disk0:/anyconnect-win-2.4.1012-k9.pkg 1 svc enable group-policy EASYVPN internal group-policy EASYVPN attributes dns-server value 10.0.0.101 vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn split-tunnel-policy tunnelspecified split-tunnel-network-list value SPLIT-TUNNEL-VPN ! tunnel-group client type remote-access tunnel-group client general-attributes address-pool (inside) IPSECVPN-POOL address-pool IPSECVPN-POOL default-group-policy EASYVPN dhcp-server 10.0.0.253 tunnel-group client ipsec-attributes pre-shared-key * tunnel-group CLIENTVPN type ipsec-l2l tunnel-group CLIENTVPN ipsec-attributes pre-shared-key * ! class-map inspection_default match default-inspection-traffic ! ! policy-map global_policy class inspection_default inspect icmp ! service-policy global_policy global prompt hostname context I'm not sure where I should go next with troubleshooting nslookup result: Default Server: blahname.blah.lan Address: 10.0.0.101

  Read the article

• Why is my mdadm raid-1 recovery so slow?

  - by dimmer

  On a system I'm running Ubuntu 10.04. My raid-1 restore started out fast but quickly became ridiculously slow (at this rate the restore will take 150 days!): dimmer@paimon:~$ cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md0 : active raid1 sdc1[2] sdb1[1] 1953513408 blocks [2/1] [_U] [====>................] recovery = 24.4% (477497344/1953513408) finish=217368.0min speed=113K/sec unused devices: <none> Eventhough I have set the kernel variables to reasonably quick values: dimmer@paimon:~$ cat /proc/sys/dev/raid/speed_limit_min 1000000 dimmer@paimon:~$ cat /proc/sys/dev/raid/speed_limit_max 100000000 I am using 2 2.0TB Western Digital Hard Disks, WDC WD20EARS-00M and WDC WD20EARS-00J. I believe they have been partitioned such that their sectors are aligned. dimmer@paimon:/sys$ sudo parted /dev/sdb GNU Parted 2.2 Using /dev/sdb Welcome to GNU Parted! Type 'help' to view a list of commands. (parted) p Model: ATA WDC WD20EARS-00M (scsi) Disk /dev/sdb: 2000GB Sector size (logical/physical): 512B/512B Partition Table: gpt Number Start End Size File system Name Flags 1 1049kB 2000GB 2000GB ext4 (parted) unit s (parted) p Number Start End Size File system Name Flags 1 2048s 3907028991s 3907026944s ext4 (parted) q dimmer@paimon:/sys$ sudo parted /dev/sdc GNU Parted 2.2 Using /dev/sdc Welcome to GNU Parted! Type 'help' to view a list of commands. (parted) p Model: ATA WDC WD20EARS-00J (scsi) Disk /dev/sdc: 2000GB Sector size (logical/physical): 512B/4096B Partition Table: gpt Number Start End Size File system Name Flags 1 1049kB 2000GB 2000GB ext4 I am beginning to think that I have a hardware problem, otherwise I can't imagine why the mdadm restore should be so slow. I have done a benchmark on /dev/sdc using Ubuntu's disk utility GUI app, and the results looked normal so I know that sdc has the capability to write faster than this. I also had the same problem on a similar WD drive that I RMAd because of bad sectors. I suppose it's possible they sent me a replacement with bad sectors too, although there are no SMART values showing them yet. Any ideas? Thanks. As requested, output of top sorted by cpu usage (notice there is ~0 cpu usage). iowait is also zero which seems strange: top - 11:35:13 up 2 days, 9:40, 3 users, load average: 2.87, 2.58, 2.30 Tasks: 142 total, 1 running, 141 sleeping, 0 stopped, 0 zombie Cpu(s): 0.0%us, 0.2%sy, 0.0%ni, 99.8%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 3096304k total, 1482164k used, 1614140k free, 617672k buffers Swap: 1526132k total, 0k used, 1526132k free, 535416k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 45 root 20 0 0 0 0 S 0 0.0 2:17.02 scsi_eh_0 1 root 20 0 2808 1752 1204 S 0 0.1 0:00.46 init 2 root 20 0 0 0 0 S 0 0.0 0:00.00 kthreadd 3 root RT 0 0 0 0 S 0 0.0 0:00.02 migration/0 4 root 20 0 0 0 0 S 0 0.0 0:00.17 ksoftirqd/0 5 root RT 0 0 0 0 S 0 0.0 0:00.00 watchdog/0 6 root RT 0 0 0 0 S 0 0.0 0:00.02 migration/1 ... dmesg errors, definitely looking like hardware: [202884.000157] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [202884.007015] ata5.00: failed command: FLUSH CACHE EXT [202884.013728] ata5.00: cmd ea/00:00:00:00:00/00:00:00:00:00/a0 tag 0 [202884.013730] res 40/00:00:ff:59:2e/00:00:35:00:00/e0 Emask 0x4 (timeout) [202884.033667] ata5.00: status: { DRDY } [202884.040329] ata5: hard resetting link [202889.400050] ata5: link is slow to respond, please be patient (ready=0) [202894.048087] ata5: COMRESET failed (errno=-16) [202894.054663] ata5: hard resetting link [202899.412049] ata5: link is slow to respond, please be patient (ready=0) [202904.060107] ata5: COMRESET failed (errno=-16) [202904.066646] ata5: hard resetting link [202905.840056] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [202905.849178] ata5.00: configured for UDMA/133 [202905.849188] ata5: EH complete [203899.000292] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [203899.007096] ata5.00: failed command: IDENTIFY DEVICE [203899.013841] ata5.00: cmd ec/00:01:00:00:00/00:00:00:00:00/00 tag 0 pio 512 in [203899.013843] res 40/00:00:ff:f9:f6/00:00:38:00:00/e0 Emask 0x4 (timeout) [203899.041232] ata5.00: status: { DRDY } [203899.048133] ata5: hard resetting link [203899.816134] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [203899.826062] ata5.00: configured for UDMA/133 [203899.826079] ata5: EH complete [204375.000200] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [204375.007421] ata5.00: failed command: IDENTIFY DEVICE [204375.014799] ata5.00: cmd ec/00:01:00:00:00/00:00:00:00:00/00 tag 0 pio 512 in [204375.014800] res 40/00:00:ff:0c:0f/00:00:39:00:00/e0 Emask 0x4 (timeout) [204375.044374] ata5.00: status: { DRDY } [204375.051842] ata5: hard resetting link [204380.408049] ata5: link is slow to respond, please be patient (ready=0) [204384.440076] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [204384.449938] ata5.00: configured for UDMA/133 [204384.449955] ata5: EH complete [204395.988135] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [204395.988140] ata5.00: failed command: IDENTIFY DEVICE [204395.988147] ata5.00: cmd ec/00:01:00:00:00/00:00:00:00:00/00 tag 0 pio 512 in [204395.988149] res 40/00:00:ff:0c:0f/00:00:39:00:00/e0 Emask 0x4 (timeout) [204395.988151] ata5.00: status: { DRDY } [204395.988156] ata5: hard resetting link [204399.320075] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [204399.330487] ata5.00: configured for UDMA/133 [204399.330503] ata5: EH complete

  Read the article

• Making nginx withstand flood attacks

  - by Tiffany Walker

  How can I make it stand stand against attacks better? Are their plugins. Looking for a way to RATE LIMIT and remain up and not slow down. My Setup: user nobody; # no need for more workers in the proxy mode worker_processes 4; worker_cpu_affinity 0001 0010 0100 1000; worker_priority -2; error_log /var/log/nginx/error.log info; worker_rlimit_nofile 40480; events { worker_connections 5120; # increase for busier servers use epoll; # you should use epoll here for Linux kernels 2.6.x } http { server_name_in_redirect off; server_names_hash_max_size 10240; server_names_hash_bucket_size 1024; include mime.types; default_type application/octet-stream; server_tokens off; disable_symlinks if_not_owner; sendfile on; tcp_nopush on; tcp_nodelay on; keepalive_timeout 5; gzip on; gzip_vary on; gzip_disable "MSIE [1-6]\."; gzip_proxied any; gzip_http_version 1.1; gzip_min_length 1000; gzip_comp_level 9; gzip_buffers 16 8k; # You can remove image/png image/x-icon image/gif image/jpeg if you have slow CPU gzip_types text/plain text/xml text/css application/x-javascript application/xml image/png image/x-icon image/gif image/jpeg application/xml+rss text/javascript application/atom+xml; ignore_invalid_headers on; client_header_timeout 3m; client_body_timeout 3m; send_timeout 3m; reset_timedout_connection on; connection_pool_size 256; client_header_buffer_size 256k; large_client_header_buffers 4 256k; client_max_body_size 200M; client_body_buffer_size 128k; request_pool_size 32k; output_buffers 4 32k; postpone_output 1460; proxy_temp_path /tmp/nginx_proxy/; client_body_in_file_only on; log_format bytes_log "$msec $bytes_sent ."; include "/etc/nginx/vhosts/*"; } vhost file: server { error_log /var/log/nginx/vhost-error_log warn; listen 194.145.208.19:80; server_name ipxnow.in www.ipxnow.in; access_log /usr/local/apache/domlogs/ipxnow.in-bytes_log bytes_log; access_log /usr/local/apache/domlogs/ipxnow.in combined; root /home/ipxnowin/public_html; location / { location ~.*\.(3gp|gif|jpg|jpeg|png|ico|wmv|avi|asf|asx|mpg|mpeg|mp4|pls|mp3|mid|wav|swf|flv|html|htm|txt|js|css|exe|zip|tar|rar|gz|tgz|bz2|uha|7z|doc|docx|xls|xlsx|pdf|iso)$ { expires 7d; try_files $uri @backend; } error_page 405 = @backend; add_header X-Cache "HIT from Backend"; proxy_pass http://194.145.208.19:8081; include proxy.inc; } location @backend { internal; proxy_pass http://194.145.208.19:8081; include proxy.inc; } location ~ .*\.(php|jsp|cgi|pl|py)?$ { proxy_pass http://194.145.208.19:8081; include proxy.inc; } location ~ /\.ht { deny all; } } and proxy.inc: proxy_connect_timeout 59s; proxy_send_timeout 600; proxy_read_timeout 600; proxy_buffer_size 64k; proxy_buffers 16 32k; proxy_busy_buffers_size 64k; proxy_temp_file_write_size 64k; proxy_pass_header Set-Cookie; proxy_redirect off; proxy_hide_header Vary; proxy_set_header Accept-Encoding ''; proxy_ignore_headers Cache-Control Expires; proxy_set_header Referer $http_referer; proxy_set_header Host $host; proxy_set_header Cookie $http_cookie; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-Host $host; proxy_set_header X-Forwarded-Server $host; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for;

  Read the article

• local user cannot access vsftpd server

  - by Zloy Smiertniy

  I'm currently running a vsftpd server and I added the necessary configurations in vsftpd.conf so that local users can use clients like FileZilla to manage their homes in a server. I found out that only users in the sudoers list access without a problem only they can't download the files, but users that are not sudoers cannot even access their homes from a client but they can access by a web browser using the FTP protocol and they can only access their home directories (as intented) Im running a fedora 14 on my server and my vsftpd.conf looks like this: # Example config file /etc/vsftpd/vsftpd.conf # # The default compiled in settings are fairly paranoid. This sample file # loosens things up a bit, to make the ftp daemon more usable. # Please see vsftpd.conf.5 for all compiled in defaults. # # READ THIS: This example file is NOT an exhaustive list of vsftpd options. # Please read the vsftpd.conf.5 manual page to get a full idea of vsftpd's # capabilities. # # Allow anonymous FTP? (Beware - allowed by default if you comment this out). anonymous_enable=NO # # Uncomment this to allow local users to log in. local_enable=YES # # Uncomment this to enable any form of FTP write command. write_enable=YES # # Default umask for local users is 077. You may wish to change this to 022, # if your users expect that (022 is used by most other ftpd's) local_umask=022 # # Uncomment this to allow the anonymous FTP user to upload files. This only # has an effect if the above global write enable is activated. Also, you will # obviously need to create a directory writable by the FTP user. #anon_upload_enable=YES # # Uncomment this if you want the anonymous FTP user to be able to create # new directories. #anon_mkdir_write_enable=YES # # Activate directory messages - messages given to remote users when they # go into a certain directory. dirmessage_enable=YES # # The target log file can be vsftpd_log_file or xferlog_file. # This depends on setting xferlog_std_format parameter xferlog_enable=YES # # Make sure PORT transfer connections originate from port 20 (ftp-data). connect_from_port_20=YES # # If you want, you can arrange for uploaded anonymous files to be owned by # a different user. Note! Using "root" for uploaded files is not # recommended! #chown_uploads=YES #chown_username=whoever # # The name of log file when xferlog_enable=YES and xferlog_std_format=YES # WARNING - changing this filename affects /etc/logrotate.d/vsftpd.log #xferlog_file=/var/log/xferlog # # Switches between logging into vsftpd_log_file and xferlog_file files. # NO writes to vsftpd_log_file, YES to xferlog_file xferlog_std_format=YES # # You may change the default value for timing out an idle session. #idle_session_timeout=600 # # You may change the default value for timing out a data connection. #data_connection_timeout=120 # # It is recommended that you define on your system a unique user which the # ftp server can use as a totally isolated and unprivileged user. #nopriv_user=ftpsecure # # Enable this and the server will recognise asynchronous ABOR requests. Not # recommended for security (the code is non-trivial). Not enabling it, # however, may confuse older FTP clients. #async_abor_enable=YES # # By default the server will pretend to allow ASCII mode but in fact ignore # the request. Turn on the below options to have the server actually do ASCII # mangling on files when in ASCII mode. # Beware that on some FTP servers, ASCII support allows a denial of service # attack (DoS) via the command "SIZE /big/file" in ASCII mode. vsftpd # predicted this attack and has always been safe, reporting the size of the # raw file. # ASCII mangling is a horrible feature of the protocol. ascii_upload_enable=YES ascii_download_enable=YES # # You may fully customise the login banner string: ftpd_banner=Welcome to GAMBITA FTP service # # You may specify a file of disallowed anonymous e-mail addresses. Apparently # useful for combatting certain DoS attacks. #deny_email_enable=YES # (default follows) #banned_email_file=/etc/vsftpd/banned_emails # # You may specify an explicit list of local users to chroot() to their home # directory. If chroot_local_user is YES, then this list becomes a list of # users to NOT chroot(). chroot_local_user=YES chroot_list_enable=YES # (default follows) chroot_list_file=/etc/vsftpd/chroot_list # # You may activate the "-R" option to the builtin ls. This is disabled by # default to avoid remote users being able to cause excessive I/O on large # sites. However, some broken FTP clients such as "ncftp" and "mirror" assume # the presence of the "-R" option, so there is a strong case for enabling it. ls_recurse_enable=YES # # When "listen" directive is enabled, vsftpd runs in standalone mode and # listens on IPv4 sockets. This directive cannot be used in conjunction # with the listen_ipv6 directive. listen=YES # # This directive enables listening on IPv6 sockets. To listen on IPv4 and IPv6 # sockets, you must run two copies of vsftpd with two configuration files. # Make sure, that one of the listen options is commented !! #listen_ipv6=YES pam_service_name=vsftpd userlist_enable=YES tcp_wrappers=YES use_localtime=YES Anyone has an idea of what might be happening? Nothing concerning vsftpd is written in any log

  Read the article

• FFmpeg creates emtpy (black) frames

  - by resamsel

  I have a set of images from a timelapse shot (172 JPG files) that I want to convert into a movie. I tried several parameters with FFmpeg, but all I get is a video with black frames (though it has the expected length). ffmpeg -f image2 -vcodec mjpeg -y -i img_%03d.jpg timelapse2.mpg The command above creates this video: http://sdm-net.org/data/timelapse2.mpg What I'm expecting is something like this (created with Time Lapse Assembler.app): https://vimeo.com/39038362 - This is my fallback option, but I'd really like to create timelapse movies from a script. I'm on OSX Lion (10.7.3) with FFmpeg version (0.10) installed via Homebrew. I also tried to find a proper version of mencoder for OSX, but this doesn't seem to be an easy task. Also, ImageMagick's convert doesn't seem to work nicely, it creates really bad output and it seems there's not much I can do about it... Edit: With libx264 and an mp4 container: ffmpeg -f image2 -y -i img_%03d.jpg -vcodec libx264 timelapse4.mp4 Output: ffmpeg version 0.10 Copyright (c) 2000-2012 the FFmpeg developers built on Mar 26 2012 13:47:02 with clang 3.0 (tags/Apple/clang-211.12) configuration: --prefix=/usr/local/Cellar/ffmpeg/0.10 --enable-shared --enable-gpl --enable-version3 --enable-nonfree --enable-hardcoded-tables --enable-libfreetype --cc=/usr/bin/clang --enable-libx264 --enable-libfaac --enable-libmp3lame --enable-librtmp --enable-libtheora --enable-libvorbis --enable-libvpx --enable-libxvid --enable-libopencore-amrnb --enable-libopencore-amrwb --enable-libass --disable-ffplay libavutil 51. 34.101 / 51. 34.101 libavcodec 53. 60.100 / 53. 60.100 libavformat 53. 31.100 / 53. 31.100 libavdevice 53. 4.100 / 53. 4.100 libavfilter 2. 60.100 / 2. 60.100 libswscale 2. 1.100 / 2. 1.100 libswresample 0. 6.100 / 0. 6.100 libpostproc 52. 0.100 / 52. 0.100 Input #0, image2, from 'img_%03d.jpg': Duration: 00:00:06.88, start: 0.000000, bitrate: N/A Stream #0:0: Video: mjpeg, yuvj420p, 3888x2592 [SAR 72:72 DAR 3:2], 25 fps, 25 tbr, 25 tbn, 25 tbc [buffer @ 0x7f8ec9415f20] w:3888 h:2592 pixfmt:yuvj420p tb:1/1000000 sar:72/72 sws_param: [libx264 @ 0x7f8ec981d800] using SAR=1/1 [libx264 @ 0x7f8ec981d800] frame MB size (243x162) > level limit (36864) [libx264 @ 0x7f8ec981d800] MB rate (984150) > level limit (983040) [libx264 @ 0x7f8ec981d800] using cpu capabilities: MMX2 SSE2Fast SSSE3 FastShuffle SSE4.2 AVX [libx264 @ 0x7f8ec981d800] profile High, level 5.1 [libx264 @ 0x7f8ec981d800] 264 - core 120 - H.264/MPEG-4 AVC codec - Copyleft 2003-2011 - http://www.videolan.org/x264.html - options: cabac=1 ref=3 deblock=1:0:0 analyse=0x3:0x113 me=hex subme=7 psy=1 psy_rd=1.00:0.00 mixed_ref=1 me_range=16 chroma_me=1 trellis=1 8x8dct=1 cqm=0 deadzone=21,11 fast_pskip=1 chroma_qp_offset=-2 threads=12 sliced_threads=0 nr=0 decimate=1 interlaced=0 bluray_compat=0 constrained_intra=0 bframes=3 b_pyramid=2 b_adapt=1 b_bias=0 direct=1 weightb=1 open_gop=0 weightp=2 keyint=250 keyint_min=25 scenecut=40 intra_refresh=0 rc_lookahead=40 rc=crf mbtree=1 crf=23.0 qcomp=0.60 qpmin=0 qpmax=69 qpstep=4 ip_ratio=1.40 aq=1:1.00 Output #0, mp4, to 'timelapse4.mp4': Metadata: encoder : Lavf53.31.100 Stream #0:0: Video: h264 (![0][0][0] / 0x0021), yuvj420p, 3888x2592 [SAR 72:72 DAR 3:2], q=-1--1, 25 tbn, 25 tbc Stream mapping: Stream #0:0 -> #0:0 (mjpeg -> libx264) Press [q] to stop, [?] for help frame= 172 fps= 18 q=-1.0 Lsize= 259kB time=00:00:06.80 bitrate= 312.3kbits/s video:256kB audio:0kB global headers:0kB muxing overhead 1.089647% [libx264 @ 0x7f8ec981d800] frame I:1 Avg QP: 9.60 size:212820 [libx264 @ 0x7f8ec981d800] frame P:43 Avg QP:30.50 size: 291 [libx264 @ 0x7f8ec981d800] frame B:128 Avg QP:31.00 size: 285 [libx264 @ 0x7f8ec981d800] consecutive B-frames: 0.6% 0.0% 1.7% 97.7% [libx264 @ 0x7f8ec981d800] mb I I16..4: 22.5% 77.2% 0.3% [libx264 @ 0x7f8ec981d800] mb P I16..4: 0.0% 0.0% 0.0% P16..4: 0.0% 0.0% 0.0% 0.0% 0.0% skip:100.0% [libx264 @ 0x7f8ec981d800] mb B I16..4: 0.0% 0.0% 0.0% B16..8: 0.0% 0.0% 0.0% direct: 0.0% skip:100.0% L0: 1.2% L1:98.8% BI: 0.0% [libx264 @ 0x7f8ec981d800] 8x8 transform intra:77.2% inter:100.0% [libx264 @ 0x7f8ec981d800] coded y,uvDC,uvAC intra: 41.2% 23.4% 0.6% inter: 0.0% 0.0% 0.0% [libx264 @ 0x7f8ec981d800] i16 v,h,dc,p: 40% 25% 35% 1% [libx264 @ 0x7f8ec981d800] i8 v,h,dc,ddl,ddr,vr,hd,vl,hu: 36% 32% 30% 1% 0% 0% 0% 0% 0% [libx264 @ 0x7f8ec981d800] i4 v,h,dc,ddl,ddr,vr,hd,vl,hu: 51% 40% 6% 1% 1% 0% 1% 0% 1% [libx264 @ 0x7f8ec981d800] i8c dc,h,v,p: 60% 21% 19% 0% [libx264 @ 0x7f8ec981d800] Weighted P-Frames: Y:0.0% UV:0.0% [libx264 @ 0x7f8ec981d800] ref P L0: 92.3% 0.0% 0.0% 7.7% [libx264 @ 0x7f8ec981d800] ref B L0: 50.0% 0.0% 50.0% [libx264 @ 0x7f8ec981d800] ref B L1: 99.4% 0.6% [libx264 @ 0x7f8ec981d800] kb/s:304.49 Output timelapse4.mp4 (beacause of spam protection I can only post two links with my reputation): http sdm-net.org/data/timelapse4.mp4

  Read the article

• DDNS Not Creating Journal (Dhcpd and Named)

  - by user130094

  * EDIT 1 * After monkeying with additional debug logging I see some log entries of interest. 27-Jul-2012 23:45:26.537 general: error: zone example.lan/IN/internal: journal rollforward failed: no more 27-Jul-2012 23:45:26.537 general: error: zone example.lan/IN/internal: not loaded due to errors. ^^^ If I can remedy the above messages I think I'll be good to go ^^^ * EDIT 2 * Grasping at straws I touched a forward and a reverse zone journal file and restarted named. Boom! Works. Despite documentation stating the files are created automatically and what I have seen before... dunno why but that did the trick. Also re-checked perms on the dir the files live in. As certain as I was, they were correct with named having rw. CentOS 6 (final) dhcpd 4.1.1-P1 named BIND 9.8.2rc1-RedHat-9.8.2-0.10.rc1.el6 Basic DHCP and DNS functionality are in place on 192.168.111.2. Clients are assigned addresses as intended and can resolve local DNS names as well as Internet names. My problem is that named's zone journal files are not created. chroot: /var/named/chroot I tried placing the zone files in various directories (/var/named/data, /var/named, /var/named/dynamic - no matter which dir with named owning and wide open perms I now get nowhere). Along the way I, at one point, got a permission denied when named tried to create the journal. Resolved the issue by: chown --recursive named:named /var/named chmod --recursive 777 /var/named The journal was then created and here's where things fell apart. I attempted to tame permissions to something more sane and broke it. Once changed and having restarted named it threw an error indicating the journal was out of sync (or something to that affect)... didn't matter since this is a new setup so I deleted it and now it is not recreated. Now though I see no errors in /var/log/messages, my chrooted /var/log/named.log, or chrooted /var/log/named.debug. I increased the debug level with 'rndc trace' - no love. Increased trace to 10, still nothing. SELinux is disabled... [root@server temp]# sestatus SELinux status: disabled dhcpd.conf... allow client-updates; ddns-update-style interim; subnet 192.168.111.0 netmask 255.255.255.224 { ... key dhcpudpate { algorithm hmac-md5; secret LDJMdPdEZED+/nN/AGO9ZA==; } zone example.lan. { primary 192.168.111.2; key dhcpudpate; } } named.conf... key dhcpudpate { algorithm hmac-md5; secret "LDJMdPdEZED+/nN/AGO9ZA=="; }; zone "example.lan" { type master; file "/var/named/dynamic/example.lan.db"; allow-transfer { none; }; allow-update { key dhcpudpate; }; notify false; check-names ignore; }; The following shows /var/log/named.log output of named starting up - no errors. 27-Jul-2012 21:33:39.349 general: info: zone 111.168.192.in-addr.arpa/IN/internal: loaded serial 2012072601 27-Jul-2012 21:33:39.349 general: info: zone example.lan/IN/internal: loaded serial 2012072501 27-Jul-2012 21:33:39.350 general: info: zone example2.lan/IN/internal: loaded serial 2012072501 27-Jul-2012 21:33:39.350 general: info: zone example3.lan/IN/internal: loaded serial 2012072601 27-Jul-2012 21:33:39.350 general: info: zone example4.lan/IN/internal: loaded serial 2012072501 27-Jul-2012 21:33:39.351 general: info: zone example5.lan/IN/internal: loaded serial 2012072501 27-Jul-2012 21:33:39.351 general: info: managed-keys-zone ./IN/internal: loaded serial 0 27-Jul-2012 21:33:39.351 general: info: zone example.lan/IN/external: loaded serial 2012072501 27-Jul-2012 21:33:39.352 general: info: zone example1.lan/IN/external: loaded serial 2012072501 27-Jul-2012 21:33:39.352 general: info: zone example2.lan/IN/external: loaded serial 2012072501 27-Jul-2012 21:33:39.352 general: info: zone example3.lan/IN/external: loaded serial 2012072501 27-Jul-2012 21:33:39.353 general: info: managed-keys-zone ./IN/external: loaded serial 0 27-Jul-2012 21:33:39.353 general: notice: running 27-Jul-2012 21:34:03.825 general: info: received control channel command 'trace 10' 27-Jul-2012 21:34:03.825 general: info: debug level is now 10 ...and /var/log/messages for a named start... Jul 27 23:02:04 server named[9124]: ---------------------------------------------------- Jul 27 23:02:04 server named[9124]: BIND 9 is maintained by Internet Systems Consortium, Jul 27 23:02:04 server named[9124]: Inc. (ISC), a non-profit 501(c)(3) public-benefit Jul 27 23:02:04 server named[9124]: corporation. Support and training for BIND 9 are Jul 27 23:02:04 server named[9124]: available at https://www.isc.org/support Jul 27 23:02:04 server named[9124]: ---------------------------------------------------- Jul 27 23:02:04 server named[9124]: adjusted limit on open files from 4096 to 1048576 Jul 27 23:02:04 server named[9124]: found 2 CPUs, using 2 worker threads Jul 27 23:02:04 server named[9124]: using up to 4096 sockets Jul 27 23:02:04 server named[9124]: loading configuration from '/etc/named.conf' Jul 27 23:02:04 server named[9124]: using default UDP/IPv4 port range: [1024, 65535] Jul 27 23:02:04 server named[9124]: using default UDP/IPv6 port range: [1024, 65535] Jul 27 23:02:04 server named[9124]: listening on IPv4 interface eth0, 192.168.111.2#53 Jul 27 23:02:04 server named[9124]: generating session key for dynamic DNS Jul 27 23:02:04 server named[9124]: sizing zone task pool based on 12 zones Jul 27 23:02:04 server named[9124]: set up managed keys zone for view internal, file 'dynamic/3bed2cb3a3acf7b6a8ef408420cc682d5520e26976d354254f528c965612054f.mkeys' Jul 27 23:02:04 server named[9124]: set up managed keys zone for view external, file 'dynamic/3c4623849a49a53911c4a3e48d8cead8a1858960bccdea7a1b978d73ec2f06d7.mkeys' Jul 27 23:02:04 server named[9124]: command channel listening on 127.0.0.1#953 What can I do to troubleshoot this further? It almost seems as though dhcpd is not triggering the update. Maybe I should troubleshoot here and, if so, how? Many thanks.

  Read the article

• ASA 5505 Vlan question

  - by Wayne

  I am setting up a cisco asa 5505 with the base license. I can communicate from inside-outside, outside-inside, inside-home, which is my desired traffic security. I can get http, ssh, and other access from inside-home, but I can't ping from inside-home (192.168.110.0 host to 192.168.7.1 or 192.168.7.0 host). Can someone explain. My config is listed below interface Vlan1<br> nameif inside<br> security-level 100<br> ip address 192.168.110.254 255.255.255.0 <br> !<br> interface Vlan2<br> nameif outside<br> security-level 0<br> pppoe client vpdn group birdie<br> ip address removedIP 255.255.255.255 pppoe <br> !<br> interface Vlan3<br> no forward interface Vlan1<br> nameif home<br> security-level 50<br> ip address 192.168.7.1 255.255.255.0 <br> ! <br> interface Ethernet0/0<br> switchport access vlan 2<br> ! <br> interface Ethernet0/1<br> ! <br> interface Ethernet0/2<br> ! <br> interface Ethernet0/3<br> ! <br> interface Ethernet0/4<br> switchport access vlan 3<br> ! <br> interface Ethernet0/5<br> shutdown <br> ! <br> interface Ethernet0/6<br> shutdown <br> ! <br> interface Ethernet0/7<br> shutdown <br> ! <br> ftp mode passive<br> clock timezone EST -5<br> clock summer-time EDT recurring<br> access-list Outside-In extended permit icmp any any <br> access-list Outside-In extended permit tcp any any eq www <br> access-list Outside-In extended permit tcp any any eq https <br> access-list Outside-In extended permit tcp any any eq 5969 <br> access-list inside_nat0_outbound extended permit ip any 192.168.111.0 255.255.255.224 <br> access-list standardUser_splitTunnelAcl1 extended permit ip 192.168.111.0 255.255.255.0 any <br> access-list standardUser_splitTunnelAcl1 extended permit ip 192.168.110.0 255.255.255.0 <br>any access-list inside_in extended permit icmp any any <br> access-list inside_in extended permit ip any any <br> access-list home_in extended permit icmp any any <br> access-list home_in extended permit ip any any <br> pager lines 24<br> logging enable<br> logging asdm informational<br> mtu inside 1492<br> mtu outside 1492<br> mtu home 1500 <br> ip local pool vpnuser 192.168.111.5-192.168.111.20<br> icmp unreachable rate-limit 1 burst-size 1<br> asdm image disk0:/asdm-524.bin<br> no asdm history enable<br> arp timeout 14400<br> nat-control <br> global (outside) 1 interface<br> nat (inside) 0 access-list inside_nat0_outbound<br> nat (inside) 1 0.0.0.0 0.0.0.0<br> nat (home) 1 192.168.7.0 255.255.255.0<br> static (inside,outside) tcp interface https 192.168.110.6 https netmask 255.255.255.255 <br> static (inside,outside) tcp interface www 192.168.110.6 www netmask 255.255.255.255 <br> static (inside,outside) tcp interface 5969 192.168.110.12 5969 netmask 255.255.255.255 <br> static (inside,home) 192.168.110.0 192.168.110.0 netmask 255.255.255.0 <br> access-group inside_in in interface inside<br> access-group Outside-In in interface outside<br> access-group home_in in interface home<br> route outside 0.0.0.0 0.0.0.0 RemovedIP 1<br>

  Read the article

• Should I go along with my choice of web hosting company or still search?

  - by Devner

  Hi all, I have been searching for a good website hosting company that can offer me all the services that I need for hosting my PHP & MySQL based website. Now this is a community based website and users will be able to upload pictures, etc. The hosting company that I have in mind, currently lets me do everything... let me use mail(), supports CRON jobs, etc. Of course they are charging about $6/month. Now the only problem with this company is that they have a limit of 50,000 files that can exist within the hosting account at any time. This kind of contradicts their frontpage ad of "UNLIMITED SPACE" on their website. Apart from this, I know of no other reason why I should not go with this hosting company. But my issue is that 50,000 file limit is what I cannot live with, once the users increase in significant number and the files they upload, exceed 50,000 in number. Now since this is a dynamic website and also includes sensitive issues like payments, etc. I am not sure if I should go ahead with this company as I am just starting out and then later switch over to a better hosting company which does not limit me with 50,000 files. If I need to switch over once I host with this company, I will need to take backups of all the files located in my account (jpg, zip, etc.), then upload them to the new host. I am not aware of any tools that can help me in this process. Can you please mention if you know any? I can go ahead with the other companies right now, but their cost is double/triple of the current price and they all sport less features than my current choice. If I pay more, then they are ready to accommodate my higher demands. Unfortunately, the company that I am willing to go with now, does NOT have any other higher/better plans that I can switch to. So that's the really really bad part. So my question(s): Since I am starting out with my website and since the scope of users initially is going to be less/small, should I go ahead with the current choice and then once the demand increases, switch over to a better provider? If yes, how can I transfer my database, especially the jpg files, etc. to the new provider? I don't even know the tools required to backup and restore to another host. (I don't like this idea but still..) Should I go ahead and pay more right now and go with better providers (without knowing if the website is going to do really that well) just for saving myself the trouble of having to take a backup of the 50,000 files and upload to a new host from an old host and just start paying double/triple the price without even knowing if I would receive back the returns as I expected? Backup and Restore in such a bulky numbers is something that I have never done before and hence I am stuck here trying to decide what to do. The price per month is also a considerable factor in my decision. All these web hosting companies say one common thing: It is customers responsibility to backup and restore data and they are not liable for any loss. So no matter what hosting company that I would like to go with, they ask me to take backup via FTP so that I can restore them whenever I want (& it seems to be safer to have the files locally with me). Some are providing tools for backup and some are not and I am not sure how much their backup tools can be trusted considering the disclaimers they have. I have never backed-up and restored 50,000 files from one web host to another, so please, all you experienced people out there, leave your comments and let me know your suggestions so that I can decide. I have spent 2 days fighting with myself trying to decide what to do and finally concluded that this is a double-edged sword and I can't arrive at a satisfactory final decision without involving others suggestions. I believe that someone must be out there who may have had such troublesome decision to make. So all your suggestions to help me make my decision are appreciated. Thank you all.

  Read the article

• ASA 5540 v8.4(3) vpn to ASA 5505 v8.2(5), tunnel up but I cant ping from 5505 to IP on other side

  - by user223833

  I am having problems pinging from a 5505(remote) to IP 10.160.70.10 in the network behind the 5540(HQ side). 5505 inside IP: 10.56.0.1 Out: 71.43.109.226 5540 Inside: 10.1.0.8 out: 64.129.214.27 I Can ping from 5540 to 5505 inside 10.56.0.1. I also ran ASDM packet tracer in both directions, it is ok from 5540 to 5505, but drops the packet from 5505 to 5540. It gets through the ACL and dies at the NAT. Here is the 5505 config, I am sure it is something simple I am missing. ASA Version 8.2(5) ! hostname ASA-CITYSOUTHDEPOT domain-name rngint.net names ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! interface Vlan1 nameif inside security-level 100 ip address 10.56.0.1 255.255.0.0 ! interface Vlan2 nameif outside security-level 0 ip address 71.43.109.226 255.255.255.252 ! banner motd ***ASA-CITYSOUTHDEPOT*** banner asdm CITY SOUTH DEPOT ASA5505 ftp mode passive clock timezone EST -5 clock summer-time EDT recurring dns server-group DefaultDNS domain-name rngint.net access-list outside_1_cryptomap extended permit ip host 71.43.109.226 host 10.1.0.125 access-list outside_1_cryptomap extended permit ip 10.56.0.0 255.255.0.0 10.0.0.0 255.0.0.0 access-list outside_1_cryptomap extended permit ip 10.56.0.0 255.255.0.0 10.106.70.0 255.255.255.0 access-list outside_1_cryptomap extended permit ip 10.56.0.0 255.255.0.0 10.106.130.0 255.255.255.0 access-list outside_1_cryptomap extended permit ip host 71.43.109.226 host 10.160.70.10 access-list inside_nat0_outbound extended permit ip host 71.43.109.226 host 10.1.0.125 access-list inside_nat0_outbound extended permit ip 10.56.0.0 255.255.0.0 10.0.0.0 255.0.0.0 access-list inside_nat0_outbound extended permit ip 10.56.0.0 255.255.0.0 10.106.130.0 255.255.255.0 access-list inside_nat0_outbound extended permit ip 10.56.0.0 255.255.0.0 10.106.70.0 255.255.255.0 access-list inside_nat0_outbound extended permit ip host 71.43.109.226 10.106.70.0 255.255.255.0 pager lines 24 logging enable logging buffer-size 25000 logging buffered informational logging asdm warnings mtu inside 1500 mtu outside 1500 icmp unreachable rate-limit 1 burst-size 1 icmp permit any inside no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 0.0.0.0 0.0.0.0 route outside 0.0.0.0 0.0.0.0 71.43.109.225 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy aaa-server TACACS+ protocol tacacs+ aaa-server TACACS+ (inside) host 10.106.70.36 key ***** aaa authentication http console LOCAL aaa authentication ssh console LOCAL aaa authorization exec authentication-server http server enable http 192.168.1.0 255.255.255.0 inside http 10.0.0.0 255.0.0.0 inside http 0.0.0.0 0.0.0.0 outside snmp-server host inside 10.106.70.7 community ***** no snmp-server location no snmp-server contact snmp-server community ***** snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto map outside_map 1 match address outside_1_cryptomap crypto map outside_map 1 set pfs group1 crypto map outside_map 1 set peer 64.129.214.27 crypto map outside_map 1 set transform-set ESP-3DES-SHA crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 1 authentication pre-share encryption des hash md5 group 2 lifetime 86400 telnet timeout 5 ssh 10.0.0.0 255.0.0.0 inside ssh 0.0.0.0 0.0.0.0 outside ssh timeout 5 console timeout 0 management-access inside dhcpd auto_config outside ! dhcpd address 10.56.0.100-10.56.0.121 inside dhcpd dns 10.1.0.125 interface inside dhcpd auto_config outside interface inside ! dhcprelay server 10.1.0.125 outside dhcprelay enable inside dhcprelay setroute inside dhcprelay timeout 60 threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept tftp-server inside 10.1.1.25 CITYSOUTHDEPOT-ASA-Confg webvpn tunnel-group 64.129.214.27 type ipsec-l2l tunnel-group 64.129.214.27 ipsec-attributes pre-shared-key ***** ! ! prompt hostname context

  Read the article

• Mail Server on Google Apps, Hotmail Blocks

  - by detay

  My company provides private research tools (sites) for companies. Each site has its own domain name and users. These sites need to be able to send outbound mail for notifications such as password reminders. We started using Google Apps for this purpose, but lately we are having tremendous problems with mailing, especially to hotmail. I added the SPF record as required. Mxtoolbox says my domains are not in any blacklists. I was told to contact https://postmaster.live.com/snds/addnetwork.aspx and add my network. Given that I am using google's mail servers for sending mail, should I add their IP address for registering my domain? Or should I add my server's IP even though I am not hosting the mail server on it? Here's an example of a returned message; > Delivered-To: [email protected] Received: by 10.112.1.195 with SMTP > id 3csp62757lbo; > Mon, 10 Dec 2012 10:42:55 -0800 (PST) DKIM-Signature: v=1; a=rsa-sha256; c=relaxed/relaxed; > d=gmail.com; s=20120113; > h=mime-version:from:to:x-failed-recipients:subject:message-id:date > :content-type; > bh=x41JiCH75hsonh+5c/kzwIs7R8u4Hum2u396lkV3g2w=; > b=v+bBPvufqfVkNz2UrnhyyoGj1Cuwf6x/yMj0IXJgH27uJU7TqBOvbwnNHf33sQ7B9T > uGzxwryC2fmxBh72cGz1spwWK348nUp6KK73MXKnF8mpc3nPQ8Ke+EQpSPeJdq/7oZvd > scZTGpy//IiGEUDU5bJ7YPqYXQRycY5N6AF5iI4mWWwbS4opybp3IKpDDktu11p/YEEO > Fj9wnSCx3nLMXB/XZgSjjmnaluGhYNdh3JFtz83Vmr50qXTG/TuIXlkirP73GfGvIt2S > 7sy8/YdEbZR92mYe9wucditYr7MOuyjyYrZYCg+weXeTZiJX1PfBVieD+kD9MnCairnP > rQeQ== Received: by 10.14.215.197 with SMTP id e45mr52766237eep.0.1355164974784; > Mon, 10 Dec 2012 10:42:54 -0800 (PST) MIME-Version: 1.0 Return-Path: <> Received: by 10.14.215.197 with SMTP id > e45mr65950764eep.0; Mon, 10 Dec 2012 10:42:54 -0800 (PST) From: Mail > Delivery Subsystem <[email protected]> To: > [email protected] X-Failed-Recipients: ********@hotmail.fr > Subject: Delivery Status Notification (Failure) Message-ID: > <[email protected]> Date: Mon, 10 Dec 2012 > 18:42:54 +0000 Content-Type: text/plain; charset=ISO-8859-1 > > Delivery to the following recipient failed permanently: > > *********@hotmail.fr > > Technical details of permanent failure: Message rejected. See > http://support.google.com/mail/bin/answer.py?answer=69585 for more > information. > > ----- Original message ----- > > Received: by 10.14.215.197 with SMTP id > e45mr52766228eep.0.1355164974700; > Mon, 10 Dec 2012 10:42:54 -0800 (PST) Return-Path: <[email protected]> Received: from WIN-1BBHFMJGUGS ([91.93.102.12]) > by mx.google.com with ESMTPS id l3sm26787704eem.14.2012.12.10.10.42.53 > (version=TLSv1/SSLv3 cipher=OTHER); > Mon, 10 Dec 2012 10:42:54 -0800 (PST) Message-ID: <[email protected]> MIME-Version: 1.0 > From: [email protected] To: *********@hotmail.fr Date: Mon, 10 Dec > 2012 10:42:54 -0800 (PST) Subject: Rejoignez-nous sur achbanlek.com > Content-Type: text/html; charset=utf-8 Content-Transfer-Encoding: > base64 > > ----- End of message -----

  Read the article

< Previous Page | 201 202 203 204 205 206 207 208 209 210 211 212  | Next Page >