Search Results

Search found 26912 results on 1077 pages for 'default programs'.

Page 207/1077 | < Previous Page | 203 204 205 206 207 208 209 210 211 212 213 214  | Next Page >

  • Ubuntu Laptop as a wireless hotspot on bridge mode

    - by nixnotwin
    I have a wired router to which my ubuntu laptop connects via ethernet. The wierless NIC of the laptop acts as a wireless hotspot on master mode. I use hostapd fo this. I have bridged eth0 and wlan0, so my wireless clients that connect to my laptop over wifi get ip from the wired router via dhcp, so the devices get registered at the wired router ( and the laptop is just an access point). I use the following commands to get my laptop+accesspoint working: sudo brctl addbr br0 sudo brctl addif br0 eth0 sudo hostapd /etc/hostapd/hostapd.conf & sudo dhclient -d br0 & sudo ifconfig wlan0 192.168.1.15 netmask 255.255.255.0 up sudo brctl addif br0 wlan0 These commands enable me to access internet on my wireless clients and also on the laptop which is acting as wireless accesspoint. But if I reboot the wired router (without rebooting the laptop that is acting as accesspoint), Internet access on the laptop+accesspoint gets lost, but on wireless clients it works fine. Even I have not been able to figure out a command which will reset the laptop interfaces to default settings, so everytime the router reboots, I have to reboot the laptop too to get into default settings so that I can re-enter the above mentioned commands. My first question is How can I have my bridge+accesspoint up and running even-though the router reboots? And is there a command to set the interfaces to a default state? (ifdown -a doesn't work, after issuing the command the bridge still remained).

    Read the article

  • avconv gets killed if mkv has subtitles

    - by Lukas Knuth
    What I'm trying to do is to take a movie (in an Matroska container), convert all audio tracks to AC3 and don't touch anything else. I'm using this line: avconv -i infile.mkv -map 0 -vcodec copy -scodec copy -acodec ac3 -ab 256k outfile.mkv This works fine, except when there are subtitles embedded. Then, after some time processing with no progress, avconv just "dies" (output shortened, these seem to be the interesting parts): [matroska,webm @ 0xf867a0] max_analyze_duration reached [matroska,webm @ 0xf867a0] Estimating duration from bitrate, this may be inaccurate ... Incompatible sample format 's16' for codec 'ac3', auto-selecting format 'flt' ... Stream #0.0(eng): Video: H264 / 0x34363248, yuv420p, 1280x536 [PAR 1:1 DAR 160:67], q=2-31, 1k tbn, 1k tbc (default) Stream #0.1(ger): Audio: ac3, 48000 Hz, 5.1, flt, 256 kb/s (default) Stream #0.2(eng): Audio: ac3, 48000 Hz, 5.1, flt, 256 kb/s Stream #0.3(ger): Subtitle: dvdsub (default) (forced) Metadata: title : forced Stream #0.4(ger): Subtitle: dvdsub Metadata: title : complete Stream mapping: Stream #0:0 -> #0:0 (copy) Stream #0:1 -> #0:1 (dca -> ac3) Stream #0:2 -> #0:2 (dca -> ac3) Stream #0:3 -> #0:3 (copy) Stream #0:4 -> #0:4 (copy) Input stream #0:2 frame changed from rate:48000 fmt:s16 ch:6 to rate:48000 fmt:flt ch:6 Input stream #0:1 frame changed from rate:48000 fmt:s16 ch:6 to rate:48000 fmt:flt ch:6 frame= 2606 fps=1303 q=-1.0 size= 3kB time=107.36 bitrate= 0.2kbits/s ... frame=96141 fps=813 q=-1.0 size= 2195806kB time=2807.04 bitrate=6408.2kbits/s frame=96251 fps=810 q=-1.0 size= 2195806kB time=2807.04 bitrate=6408.2kbits/s ... frame=97015 fps=397 q=-1.0 size= 2195806kB time=2807.04 bitrate=6408.2kbits/s Getötet ["Killed", in English] I have no idea why this happens, as there is no error-output. I'd like to just copy the subtitles over, not touch them at all. If that won't work, they can be completely dropped.

    Read the article

  • trying to figure out how to bridge two virtual networks together and in turn bridge that to the internet for a virtual inline IDS/IPS system

    - by Tony robinson
    I'm trying to figure out how to bridge two vmware (server or workstation, workstation) or virtualbox networks together with a linux IDS/IPS system transparently inline between both the virtual networks. How do I accomplish this? I understand how to bridge to virtual networks together, but how to I make the linux virtual machine sit between them and force traffic to go across the transparent bridge? I would like to have something along the lines of: vmnet a various vms host-only network ---- inline linux box vmnet a boxes forced to go through here to get to the internet --- vmnet b network with internet access configured as either NAT or bridged -- internet I know that basically the linux box needs two virtual nics, one on vmnet a and vmnet b, but other than that, I don't know how to force all the traffic to go across the "transparent" bridging linux box on its way to the internet. Do vmnet a and b have to be the same ip network with the same default route? does vmnet a not have a default route and vmnet b have a default route? I've read in vmware forums that on the linux host you need to change permissions on the vmnet files for promiscuous mode? is this true? how do you configure this scenario on a windows box?

    Read the article

  • pfSense router on a LAN with two gateways

    - by JohnCC
    I have a LAN with an ADSL modem/router on it. We have just gained an alternative high-speed internet connection at our location, and I want to connect the LAN to it, eventually dropping the ADSL. I've chosen to use a small PFSense box to connect the LAN to the new WAN connection. Two servers on the LAN run services accessible to the outside via NAT using the single ADSL WAN IP. We have DNS records which point to this IP. I want to do the same via the new connection, using the WAN IP there. That connection permits multiple IPs, so I have configured pfSense using virtual IP's, 1:1 NAT and appropriate firewall rules. When I change the servers' default gateway settings to the pfSense box, I can access the services via the new WAN IPs without a problem. However, I can no longer access them via the old WAN IP. If I set the servers' default gateway back to the ADSL router, then the opposite is true - I can access the services via the ADSL IP, but not via the new one. In the first case, I believe this is because an incoming SYN packet arrives at the ADSL WAN IP, and is NAT'd and sent to the internal IP of the server. The server responds with a SYN/ACK which it sends via its default gateway, the pfSense box. The pfSense box sees a SYN/ACK that it saw no SYN for and drops the packet. Is there any sensible way around this? I would like the services to be accessible via both IPs for a short period at least, since once I change the DNS it will take a while before everyone picks up the new address.

    Read the article

  • Enabling NAT forwarding using a second WAN interface and a second gateway on ubuntu

    - by nixnotwin
    I have 3 interfaces: eth0 192.168.0.50/24 eth1 10.0.0.200/24 eth2 225.228.123.211 The default gateway is 192.168.0.1 which I want to keep as it is in the changes I want to make. I want to masquerade eth1 10.0.0.200/24 and enable NAT forwarding to eth2. So I have done this: ip route add 225.228.123.208/29 dev eth2 src 225.228.123.211 table t1 ip route add default via 225.228.123.209 dev eth2 table t1 ip rule add from 225.228.123.211 table t1 ip rule add to 225.228.123.211 table t1 Now I can receive ping replies from any internet host if I did: ping -I eth2 8.8.8.8 To enable NAT forwarding I did this: sudo iptables -A FORWARD -o eth2 -i eth1 -s 10.0.0.0/24 -m conntrack --ctstate NEW -j ACCEPT sudo iptables -A FORWARD -m conntrack --ctstate ESTABLISHED,RELATED -j ACCEPT sudo iptables -t nat -A POSTROUTING -o eth1 -j MASQUERADE But it isn't working. To test I used a client pc and put it on 10.0.0.0/24 network and gateway was set as 10.0.0.200. I want to have 192.168.0.1 as default gateway. And the traffic that comes in via eth1 10.0.0.200/24 should be forwarded to eth2 225.228.123.211. I have enabled forwarding on ubuntua also.

    Read the article

  • How can I find out if a port is opened or not?

    - by Roman
    I have installed Apache server on my Windows 7 computer. I was able to display the default index.php by typing http://localhost/ in the address line of my browser. However, I am still unable to see this page by typing IP address of my computer (neither locally (from the same computer) no globally (from another computer connected to the Internet)). I was told that I need to open port 80. I did it (in a way described here) but it did not solve the problem. First of all I would like to check which ports are opened and which are not. For example I am not sure that my port 80 was closed before I tried to open. I am also not sure that it is opened after I tried to open it. I tried to run a very simple web server written in Python. For that I used port 81 and it worked! And I did not try to open the port 81. So, it was opened by default. So, if 81 is opened by default, why 80 is not? Or it is? ADDITIONAL INFORMATION: 1. In my httpd.conf file I have "Listen 80". 2. This site tells me that port 80 on my computer is opened. 3. I get different responses if I try http://myip:80 and http://myip:81. In the last case browser (Chrome) writes me that link is broken. In the first case I get: Forbidden You don't have permission to access / on this server. 4. IE writes that "The website declined to show this webpage".

    Read the article

  • erlyvideo server doesn't start automatically after reboot

    - by electroid
    I have installed erlyvideo server on ubuntu 9.10 karmic koala. Everything works fine, but after server reboot I have to start erlyvideo server manually with /etc/init.d/erlyvideo start. I try allready update-rc.d and I think erlyvideo by default should start automaticaly. Any help will be appreciated. Here erlyvideo startup script located in /etc/init.d/erlyvideo: #!/bin/sh ### BEGIN INIT INFO # Provides: erlyvideo # Required-Start: $local_fs $network # Required-Stop: $local_fs $network # Default-Start: 2 3 4 5 # Default-Stop: 0 1 6 # Short-Description: starts the erlyvideo streaming server # Description: starts the erlyvideo using erlang system ### END INIT INFO case "$1" in start) cd /opt/erlyvideo && ./bin/erlyvideo "$1" ;; stop) cd /opt/erlyvideo && ./bin/erlyvideo "$1" ;; restart) cd /opt/erlyvideo && ./bin/erlyvideo "$1" ;; soft-restart) cd /opt/erlyvideo && ./bin/erlyvideo "$1" ;; upgrade) cd /opt/erlyvideo && ./bin/erlyvideo "$1" ;; reconfigure) cd /opt/erlyvideo && ./bin/erlyvideo "$1" ;; reboot) cd /opt/erlyvideo && ./bin/erlyvideo "$1" ;; ping) cd /opt/erlyvideo && ./bin/erlyvideo "$1" ;; console) cd /opt/erlyvideo && ./bin/erlyvideo "$1" ;; attach) cd /opt/erlyvideo && ./bin/erlyvideo "$1" ;; attach-erl) cd /opt/erlyvideo && ./erts-5.8.4/bin/erl -name [email protected] -remsh [email protected] ;; *) echo $"Usage: $0 {start|stop|restart|soft-restart|upgrade|reboot|ping|console|attach}" exit 1 esac exit 0 And I have found S91erlyvideo in /etc/rc2.d next to S91apache2 which starts just fine on every reboot.

    Read the article

  • Preventing DDOS/SYN attacks (as far as possible)

    - by Godius
    Recently my CENTOS machine has been under many attacks. I run MRTG and the TCP connections graph shoots up like crazy when an attack is going on. It results in the machine becoming inaccessible. My MRTG graph: mrtg graph This is my current /etc/sysctl.conf config # Kernel sysctl configuration file for Red Hat Linux # # For binary values, 0 is disabled, 1 is enabled. See sysctl(8) and # sysctl.conf(5) for more details. # Controls IP packet forwarding net.ipv4.ip_forward = 0 # Controls source route verification net.ipv4.conf.default.rp_filter = 1 # Do not accept source routing net.ipv4.conf.default.accept_source_route = 0 # Controls the System Request debugging functionality of the kernel kernel.sysrq = 1 # Controls whether core dumps will append the PID to the core filename # Useful for debugging multi-threaded applications kernel.core_uses_pid = 1 # Controls the use of TCP syncookies net.ipv4.tcp_syncookies = 1 # Controls the maximum size of a message, in bytes kernel.msgmnb = 65536 # Controls the default maxmimum size of a mesage queue kernel.msgmax = 65536 # Controls the maximum shared segment size, in bytes kernel.shmmax = 68719476736 # Controls the maximum number of shared memory segments, in pages kernel.shmall = 4294967296 net.ipv4.conf.all.rp_filter = 1 net.ipv4.tcp_syncookies = 1 net.ipv4.icmp_echo_ignore_broadcasts = 1 net.ipv4.conf.all.accept_redirects = 0 net.ipv6.conf.all.accept_redirects = 0 net.ipv4.conf.all.send_redirects = 0 net.ipv4.conf.all.accept_source_route = 0 net.ipv4.conf.all.rp_filter = 1 net.ipv4.tcp_max_syn_backlog = 1280 Futher more in my Iptables file (/etc/sysconfig/iptables ) I only have this setup # Generated by iptables-save v1.3.5 on Mon Feb 14 07:07:31 2011 *filter :INPUT ACCEPT [1139630:287215872] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [1222418:555508541] Together with the settings above, there are about 800 IP's blocked via the iptables file by lines like: -A INPUT -s 82.77.119.47 -j DROP These have all been added by my hoster, when Ive emailed them in the past about attacks. Im no expert, but im not sure if this is ideal. My question is, what are some good things to add to the iptables file and possibly other files which would make it harder for the attackers to attack my machine without closing out any non-attacking users. Thanks in advance!

    Read the article

  • What kinds of protections against viruses does Linux provide out of the box for the average user?

    - by ChocoDeveloper
    I know others have asked this, but I have other questions related to this. In particular, I'm concerned about the damage that the virus can do the user itself (his files), not the OS in general nor other users of the same machine. This question came to my mind because of that ransomware virus that is encrypting machines all over the world, and then asking the user to send a payment in Bitcoin if he wants to recover his files. I have already received and opened the email that is supposed to contain the virus, so I guess I didn't do that bad because nothing happened. But would I have survived if I opened the attachment and it was aimed at Linux users? I guess not. One of the advantages is that files are not executable by default right after downloading them. Is that just a bad default in Windows and could be fixed with a proper configuration? As a Linux user, I thought my machine was pretty secure by default, and I was even told that I shouldn't bother installing an antivirus. But I have read some people saying that the most important (or only?) difference is that Linux is just less popular, so almost no one writes viruses for it. Is that right? What else can I do to be safe from this kind of ransomware virus? Not automatically executing random files from unknown sources seems to be more than enough, but is it? I can't think of many other things a user can do to protect his own files (not the OS, not other users), because he has full permissions on them.

    Read the article

  • Disadvantages of enabling 'Low Fragmentation Heap' LFH on Windows Server 2003?

    - by James Wiseman
    I've been investigating an issue with a production Classic ASP website running on IIS6 which seems indicative of memory fragmentation. One of the suggestions of how to ameliorate this came from Stackoverflow: How can I find why some classic asp pages randomly take a real long time to execute?. It suggested flipping a setting in the site's global.asa file to 'turn on' Low Fragmentation Heap (LFH). The following code (with a registered version of the accompanying DLL) did the trick. Set LFHObj=CreateObject("TURNONLFH.ObjTurnOnLFH") LFHObj.TurnOnLFH() application("TurnOnLFHResult")=CStr(LFHObj.TurnOnLFHResult) (Really the code isn't that important to the question). An author of a linked post reported a seemingly magic resolution to this issue, and, reading around a little more, I discovered that this setting is enabled by default on Windows Server 2008. So, naturally, this left me a little concerned: Why is this setting not enabled by default on 2003, or If it works in 2008 why have Microsoft not issued a patch to enable it by default on 2003? I suspect the answer to the above is the same for both (if there is one). Obviously, we're testing it in a non-production environment, and doing an array of metrics and comparisons to deem if it does help us. But aside from this I'm really just trying to understand if there's any technical reason why we should do this, or if there are any gotchas that we need to be aware of.

    Read the article

  • VPN messes up DNS resolution

    - by user124114
    After connecting with the Kerio VPN client (OS X Leopard) to a server, the internet (~web browsing) stopped working for the client. After poking around, the issue seems to be bad DNS server (i.e., entering IPs directly works). After disconnecting from the VPN, the invalid DNS server disappears from scutil --dns and all's well again. Now, I don't understand why OS X on the client even changes the DNS settings -- internet should be routed through a different interface, through the default gateway, not through the VPN. Questions: By what mechanism does connecting the VPN client change the "default" DNS server? How can I stop the VPN client from changing routing/DNS rules? Where is this stuff stored/modified? Before VPN: $ scutil --dns DNS configuration resolver #1 nameserver[0] : 10.66.77.1 # <---- default gateway = home router; all good order : 200000 resolver #2 domain : local options : mdns timeout : 2 order : 300000 ... VPN connected: $ scutil --dns DNS configuration resolver #1 nameserver[0] : 192.168.1.1 # <--- rubbish nameserver[1] : 192.168.2.1 order : 200000 resolver #2 domain : local options : mdns timeout : 2 order : 300000 ... The VPN doesn't appear among $ networksetup -listallnetworkservices.

    Read the article

  • SharePoint 2010 Enterprise wiki - [New page] missing

    - by icelava
    I am trying to ramp up knowledge on SharePoint deployment and usage (never did before), due to a direction to use SharePoint 2010 as a repository platform (wiki format) for our customer's infrastructure documentation. In my test virtual server, a new site of Enterprise wiki template was setup. Went into Site Actions Manage Site Features to activate Wiki Page Home Page. The default sub-web then went from /Pages to /SitePages and looks like the default Team template. The odd thing is the Site Actions is missing the New Page option. My colleague does not understand why this is the case, as it ought to be there. The original /Pages sub-web does have the option. What conditions are in play that influences the appearance of that option? UPDATE Another phenomenon observed is in the Site Actions View All Site Content view, the wiki document libraries listed in the grid will have their hyperlink (e.g. "Site Pages") lead straight to the direct default page. It would not show its own table listing of pages under that document library, unlike the original Pages document library, which expectedly show up as a listing. I wonder if this hints to any problems.

    Read the article

  • What are these CPU cache settings? Snoop Filter, ACL prefetch, HW prefetch

    - by eater
    I was in my BIOS setup turning on VT-x support today and saw these other settings. A little googling indicates that they each seem to turn on some sort of optimization to do with the CPU's L2 cache. They were all turned off by default. The processor in question is an Intel Xeon quad-core 3.4GHz (X5492). My OS is Linux 2.6.35.10-74.fc14.x86_64 #1 SMP Thu Dec 23 16:04:50 UTC 2010 x86_64 x86_64 x86_64 GNU/Linux. I have 4GB of RAM if that matters. Here's what the BIOS manufacturer has to say: Snoop Filter Enabling the snoop filter typically improves performance by reducing snoop traffic on the frontside bus in dual processor configurations. Well I like the sound of improved performance. Why would the BIOS have this off by default? Or by dual processor do they not mean multi-core? Regardless, is there a downside if this is on? ACL Prefetch When enabled, the Adjacent Cache Line Prefetcher fetches both cache lines that comprise a cache line pair when it determines required data is not currently in its cache. When disabled, the processor will only fetch the cache line required by the processor. HW Prefetch Fetches an extra line of data into L2 from external memory. Both of these sound like optimizations that have some drawbacks. What are the reasons to turn them on? What are the reasons to leave them off. Why is the default off?

    Read the article

  • OpenLDAP ACLs are not working

    - by Dr I
    First things first, I'm currently working with an OpenLDAP: slapd 2.4.36 on a Fedora release 19 (Schrödinger’s Cat). I've just install the openldap with yum and my configuration is the following one: ##### OpenLDAP Default configuration ##### # ##### OpenLDAP CORE CONFIGURATION ##### include /etc/openldap/schema/core.schema include /etc/openldap/schema/cosine.schema include /etc/openldap/schema/inetorgperson.schema include /etc/openldap/schema/nis.schema pidfile /var/lib/ldap/slapd.pid loglevel trace ##### Default Schema ##### database mdb directory /var/lib/ldap/ maxsize 1073741824 suffix "dc=domain,dc=tld" rootdn "cn=root,dc=domain,dc=tld" rootpw {SSHA}SECRETP@SSWORD ##### Default ACL ##### access to attrs=userpassword by self write by group.exact="cn=administrators,ou=builtin,ou=groups,dc=domain,dc=tld" write by anonymous auth by * none I launch my OpenLDAP service using: /usr/sbin/slapd -u ldap -h ldapi:/// ldap:/// -f /etc/openldap/slapd.conf As you can see it's a pretty simple ACL which aim to allow access to the userPassword attribute to a specific group read only, then to the owner read and write to anonymous requiring auth and refuse the access to everyone else. The problem is: Even using a valid user with correct password my ldapsearch ends with zero informations retrieved from the directory, plus I've got a strange response on the result line. # search result search: 2 result: 32 No such object # numResponses: 1 here is the ldapsearch request: ldapsearch -H ldap.domain.tld -W -b dc=domain,dc=tld -s sub -D cn=user,ou=service,ou=employees,ou=users,dc=domain,dc=tld I did not specify any filter as I want to check that ldapsearch is correctly printing only allowed attribute.

    Read the article

  • Why is this setting for Name-based Virtual Host settings not working?

    - by Kave
    I have two domains (siteA.com & SiteB.com) that point to the same webserver and I would like to show different web pages for each. The steps I have taken so far are: Copy the default site (siteA) to siteB 1) sudo cp /etc/apache2/sites-available/default /etc/apache2/sites-available/siteB 2) sudo vim /etc/apache2/sites-available/siteB <VirtualHost *:80> ServerAdmin [email protected] DocumentRoot /var/www/siteB <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/siteB> Options Indexes FollowSymLinks MultiViews AllowOverride FileInfo Indexes Order allow,deny allow from all </Directory> </VirtualHost *:80> Then I created under /var/www/siteB and created a sample index.html in there. However when I load my domain siteB.com I still get directed to /var/www/siteA. Why is that? Do I have to rename the /etc/apache2/sites-available/default to /etc/apache2/sites-available/siteA as well? UPDATE: Thanks to the answer below it seems I had forgotten next to enabling the site also another entry: <VirtualHost *:80> ServerAdmin [email protected] ServerName siteB.com ServerAlias www.siteB.com </VirtualHost *:80> in order to include all subdomains as well then do: <VirtualHost *:80> ServerAdmin [email protected] ServerName siteB.com ServerAlias *.siteB.com </VirtualHost *:80> Same goes for siteA.

    Read the article

  • Apache HTTP Server+Tomcat: Which file generates mod_jk.conf, how to modify generated stuff, and how does httpd reach it?

    - by Sk8erPeter
    I'm using XAMPP with Apache HTTP Server and Tomcat Add-On installed. There's a default mod_jk.conf which is generated by Tomcat when starting it. But which file generates this mod_jk.conf file? How can I modify default values? By default, it looks like this: pastebin - mod_jk.conf. How does Apache HTTP Server reach this file? I can't see any reference to this file when looking into httpd.conf. When I put a VirtualHost in my httpd.conf file, and I put the line JkMount /* ajp13 into it, Apache HTTP Server service can't start (causes a 7024 event id error in Event Viewer (with error code 1, but nothing specific), but puts no error messages into error.log. The VirtualHost looks like this: pastebin - VirtualHost + JkMount. This way Apache HTTP Server can not start. If I comment out the line JkMount /* ajp13, it starts without a problem. BUT if I put the following line, which is the same as in mod_jk.conf, before the mentioned VirtualHost again, the service can start! <IfModule !mod_jk.c LoadModule jk_module "C:/xampp/tomcat/xampp/apache/modules/mod_jk.so" </IfModule Why do I have to put this line in again? Why does that happen, that the http://localhost/example does work, so this query is redirected to AJP13, but I have to put the LoadModule line in again in another file? EDIT: I don't have a clue why, I surely modified something, but now /example doesn't work either... And the config above gives a 500 Internal Server Error... :S Thanks!

    Read the article

  • Conditionally set an Apache environment variable

    - by Tom McCarthy
    I would like to conditionally set the value of an Apache2 environment variable and assign a default value if one of the conditions is not met. This example if a simplification of what I'm trying to do but, in effect, if the subdomain portion of the host name is hr, finance or marketing I want to set an environment var named REQUEST_TYPE to 2, 3 or 4 respectively. Otherwise it should be 1. I tried the following configuration in httpd.conf: <VirtualHost *:80> ServerName foo.com ServerAlias *.foo.com DocumentRoot /var/www/html SetEnv REQUEST_TYPE 1 SetEnvIfNoCase Host ^hr\. REQUEST_TYPE=2 SetEnvIfNoCase Host ^finance\. REQUEST_TYPE=3 SetEnvIfNoCase Host ^marketing\. REQUEST_TYPE=4 </VirtualHost> However, the variable is always assigned a value of 1. The only way I have so far been able get it to work is to replace: SetEnv REQUEST_TYPE 1 with a regular expression containing a negative lookahead: SetEnvIfNoCase Host ^(?!hr.|finance.|marketing.) REQUEST_TYPE=1 Is there a better way to assign the default value of 1? As I add more subdomain conditions the regular expression could get ugly. Also, if I want to allow another request attribute to affect the REQUEST_TYPE (e.g. if Remote_Addr = 192.168.1.[100-150] then REQUEST_TYPE = 5) then my current method of assigning a default value (i.e. using the regular expression with a negative lookahead) probaby won't work.

    Read the article

  • Linux arp cache timeout values

    - by Jak
    I'm trying to configure sane values for the Linux kernel arp cache timeout, but I can't find a detailed explanation as to how they work anywhere. Even the kernel.org documentation doesn't give a good explanation, I can only find recommended values to alleviate overflow. Here is an example of the values I have: net.ipv4.neigh.default.gc_thresh1 = 128 net.ipv4.neigh.default.gc_thresh2 = 512 net.ipv4.neigh.default.gc_thresh3 = 1024 Now, from what I've gathered so far: gc_thresh1 is the number of arp entries allowed before the garbage collector starts removing any entries at all. gc_thresh2 is the soft-limit, which is the number of entries allowed before the garbage collector actively removes arp entries. gc_thresh3 is the hard limit, where entries above this number are aggressively removed. Now, if I understand correctly, if the number of arp entries goes beyond gc_thresh1 but remains below gc_thresh2, the excess will be removed periodically with an interval set by gc_interval. My question is, if the number of entries goes beyond gc_thresh2 but below gc_thresh3, or if the number goes beyond gc_thresh3, how are the entries removed? In other words, what does "actively" and "aggressively" removed mean exactly? I assume it means they are removed more frequently than what is defined in gc_interval, but I can't find by how much.

    Read the article

  • Issue with kernel boot [OVH SERVER]

    - by Conner Stephen McCabe
    Trying to install OpenVZ kernel on Centos 6.3, Yes my kernel is installed i can see it in the /boot folder, yes it is Rhel6 and yes it is all up to date, i checked this with yum update. My issue comes when i reboot my server with that kernel set as the default, it doesn't load, below i shall put a copy of my grub.conf file and my menu.lst file. Grub.conf: default=0 timeout=5 title vzkernel (2.6.32-042stab057.1) root (hd0,0) kernel /boot/vmlinuz-2.6.32-042stab057.1 ro root=/dev/sda1 initrd /initramfs-2.6.32-042stab057.1.img title linux centos6_64 kernel /boot/bzImage-3.2.13-xxxx-grs-ipv6-64 root=/dev/sda1 ro root (hd0,0) Now i shall paste in Menu.lst; # grub.conf generated by anaconda # # Note that you do not have to rerun grub after making changes to this file # NOTICE: You have a /boot partition. This means that # all kernel and initrd paths are relative to /boot/, eg. # root (hd0,0) # kernel /vmlinuz-version ro root=/dev/mapper/vg_stock-lv_root # initrd /initrd-[generic-]version.img #boot=/dev/sda default=0 timeout=5 splashimage=(hd0,0)/grub/splash.xpm.gz hiddenmenu title Linux OpenVZ (vmlinuz-2.6.32-042stab057.1) root (hd0,0) kernel /boot/vmlinuz-2.6.32-042stab057.1 ro root=/dev/mapper/vg_stock-lv_root rd_LVM_LV=vg_stock/lv_root rd_LVM_LV=vg_stock/lv_swap rd_NO_LUKS rd_NO_MD rd_NO_DM LANG=en_US.UTF-8 SYSFONT=l$ initrd /initramfs-2.6.32-042stab057.1.img title CentOS (2.6.32-71.el6.x86_64) root (hd0,0) kernel /boot/bzImage-3.2.13-xxxx-grs-ipv6-64 ro root=/dev/mapper/vg_stock-lv_root rd_LVM_LV=vg_stock/lv_root rd_LVM_LV=vg_stock/lv_swap rd_NO_LUKS rd_NO_MD rd_NO_DM LANG=en_US.UTF-8 SYSFO$ initrd /initramfs-2.6.32-71.el6.x86_64.img # dummy text Somebody mentioned something about OVH having added a script which changes the kernel settings or something, and suggested that we either remove the script or reinstall using a VNC, but we don't know how to go about doing either of these? Really would be great if you guys could help. Thanks in advance.

    Read the article

  • How do I connect to SSH without the password to be requested every time ? - Already follow some answers here but it doesn't work

    - by MEM
    MAC OS X Lion 10.7.3 1) On host, I've created an authorized_keys file inside .ssh folder, by doing: touch authorized_keys 2) I've copy my public ssh key into host .ssh folder by doing: scp ~/.ssh/mykey.pub [email protected]:/home/userhost/.ssh/mykey.pub 3) I've place it's contents inside authorized files by doing: cat mykey.pub >> authorized_keys 4) Then I've removed the mykey.pub file: rm mykey.pub 5) On my terminal, locally, inside my ~/.ssh folder I made: ssh-add mykey (notice that it is without the pub extension); 6) I've closed and opened again the terminal. When I first connect to this host, it has being added to the *known_hosts* file inside ~/.ssh; I've pico known_hosts and the hash is there. Still, every time I connect by doing: ssh [email protected] it requests a password ! What am I missing here ? UPDATE: I've done EVEN TWO MORE THINGS here: 7) Set your key to be the default identity - if it doesn't exist, create; touch ~/.ssh/config and place inside the following line: IdentityFile ~/.ssh/yourkeyname *id_rsa is normally your default key. You should switched to your key. This tells that the outgoing ssh connections should use this as a default identity.* 8) Add a bash process to your ssh-agent: ssh-agent bash ssh-add ~/.ssh/yourkeyname Lisinge answer helped but it's not definitive. If we restart our machine, the password gets prompted again!!! How can we debug this? What can we do here? How can we check where is this process failing ? UPDATE 2: If I use: ssh -v -i <keyfile> [email protected] I get among other things: OpenSSH_5.6p1, OpenSSL 0.9.8r 8 Feb 2011 Warning: Identity file yourkeyname not accessible: No such file or directory. This message refers to what? The identify file is not accessible on the localhost, or it's not accessible on the remote host ? Please advice

    Read the article

  • IP addresses not listed for IIS website bindings

    - by Svinn
    Recently purchased a windows cloud server godaddy. Now i installed iis7 and all other required software. And i have 50.62.1.89 and 2 more public ips. Also i have a private ip 10.1.0.2. Now the problem is am unable to access any website through any public ip. All my public ips are opening default website only. also i cant see pubic ips for IIS website bindings. Only my private ip listed for IIS binding. And in my server also public opening only default website. But am able to open websites using private ip. But my public ip addresses pointed to my server correctly. am able to open my server using remote desktop using public ip. Also as i said already public ip opening default website from IIS without problem. Please help me. Am confused for last 2 days.

    Read the article

  • Debian Wheezy IPv6 isn't configured with ifup post-up hook

    - by aef
    We recently set up a server on Debian Wheezy Beta 3 (x86_64) which has a native IPv6 connection. We configured the eth0 interface to get the IPv6 configuration through some post-up hook commands in /etc/network/interfaces. The result is, that after the booting the system up, there is only IPv4 and an auto-configured link-local IPv6 address configured on the interface, as if the command has never been executed. When we additionally place the commands after the call to ifup -a inside the /etc/init.d/networking init script, everything works as expected and we have a fully configured interface after booting up. This is quite an ugly way to configure the interface. What are we doing wrong with the ifup post-up hooks? Or is this a bug? The section from /etc/network/interfaces looks like this (IP-addresses changed): allow-hotplug eth0 iface eth0 inet static address 1.2.3.1 netmask 255.255.255.192 network 1.2.3.0 broadcast 1.2.3.63 gateway 1.2.3.62 dns-nameservers 8.8.8.8 dns-search mydomain.tld post-up ip -6 addr add 2001:db8:100:3022::2 dev eth0 post-up ip -6 route add fe80::1 dev eth0 post-up ip -6 route add default via fe80::1 dev eth0 I also tried it in this alternative way: auto eth0 iface eth0 inet static address 1.2.3.1 netmask 255.255.255.192 network 1.2.3.0 broadcast 1.2.3.63 gateway 1.2.3.62 dns-nameservers 8.8.8.8 dns-search mydomain.tld iface eth0 inet6 static address 2001:db8:100:3022::2 netmask 64 gateway fe80::1 What we added to /etc/init.d/networking: … case "$1" in start) process_options check_ifstate if [ "$CONFIGURE_INTERFACES" = no ] then log_action_msg "Not configuring network interfaces, see /etc/default/networking" exit 0 fi set -f exclusions=$(process_exclusions) log_action_begin_msg "Configuring network interfaces" if ifup -a $exclusions $verbose && ifup_hotplug $exclusions $verbose # Our additions ip -6 addr add 2001:db8:100:3022::2 dev eth0 ip -6 route add fe80::1 dev eth0 ip -6 route add default via fe80::1 dev eth0 then log_action_end_msg $? else log_action_end_msg $? fi ;; …

    Read the article

  • EC2 kernel decision and issues with creating a new machine with my AMI

    - by roacha
    I could really use some advice. I started a new instance on EC2 using Amazon's AMI and during the deployment process I selected a Kernel ID of "Use Default". I then configured my server the way that I wanted to and took a snapshot of it. I then created my own AMI to create new servers with. When I try and create a new server with this AMI the server fails to start and I get the error: EXT3-fs: sda1: couldn't mount because of unsupported optional features (240). Which appears to happen because I am selecting a kernel id of "Use default" again when building my second server. I have read that in order for this to work I need to choose the same kernel id that was used in my original server. I have deleted my original server and don't know what it was using. What is the best process to follow in order to not have these issues? Should I choose "Use Default" for my original server? How do you know which kernel it selected? Then should I just document this and always specify this during the deployment of my next servers using my custom AMI? OR should I choose a custom kernel id during the initial build and always use this one moving ahead hoping Amazon never retires it? Thanks for any advice!

    Read the article

  • How can I use an own asp page as 404 error page on a Windows 7 pro IIS 7.5 local installation

    - by Edelcom
    Running Windows 7 Pro Running local IIS 7.5 ( for web development purposes ) Edited hosts file to be able to use http://www.sitestepper.dev Site build in subfolder of the inetpub/wwwroot/staplijst Site can be viewed using http://www.sitestepper.dev/staplijst/whatever-page.htm I have an http://www.sitestepper.dev/p.asp page I would like to call when an unknown page is requested. This technique works fine on the deployed version of this web site ( deployed on an Windows 2003 server running IIS 7 - not sure about the 7 but it is the version deployed with Windows 2003 server ). I tried ( in the Edit Custom Error Dialog ) : Execute a URL on this site: with value /staplijst/p.asp and Respond with a 302 redirect: with value http://www.sitestepper.dev/staplijst/p.asp I tried this in the properties of the 'Default Web Site' , and I tried this at the staplijst level. Even tried it with values without the /staplijst. I restarted the default web site after each change. And even stopped/started the Web service. But nothing seems to work, I keep getting the 'Server Error In Application "DEFAULT WEB SITE"' , HTTP Error 404.0 error. What am I missing here - probably something obvious, but I don't see it ? Thanks in advance

    Read the article

  • Unable to set initcwnd on a Hetzner server

    - by Sergi
    We just ordered a bunch of Hetzner EX40SSD servers with the minimal Debian install image that they provide and everything is just fine except that looking at tcpdumps for fine tuning the network from various locations the initcwnd param seems to be stuck at 6 no matter how we change it. By default Debian 3.2 kernels should have that setting to 10 so it's pretty strange. Is it possible that the NIC driver or a custom setting in the Hetzner Debian image is limiting this param? Even if we set it to 4, like the old kernel default, it doesn't work. Any ideas would be much appreciated! Does anyone know if the NIC drivers provided by default by Debian have some kind on limitation. In a long thread in http://www.webhostingtalk.com/showthread.php?t=1200617&highlight=hetzner they talk about a page http://wiki.hetzner.de/index.php/Installation_des_r8168-Treibers/en where Hetzner states that the included Realtek r8168 driver is not working properly, but nowhere do they say that the initcwnd could be affected. Tomorrow i will try to install a CentOs image and see if Debian is the problem...Last resort would be to install a custom debian image, but that is a pain in the ass! Thanks!

    Read the article

< Previous Page | 203 204 205 206 207 208 209 210 211 212 213 214  | Next Page >