Search Results

Search found 5712 results on 229 pages for 'card'.

Page 208/229 | < Previous Page | 204 205 206 207 208 209 210 211 212 213 214 215  | Next Page >

• Windows Server 2003 (w/Exchange) move to new machine

  - by James Booker

  I have an ageing domain controller (the only one on a 10-pc network) which needs rebooting often. I have a Dell Poweredge 2850 server doing nothing, so I'd like to move the DC to that, but here's the catch - I don't have Win2k Server Std install media any more as it's been lost. I purchased "Easus Todo Backup Advanced Server" which claims to be able to recover to dissimilar metal, but it's not quite working (although I don't think it's the product's fault) I know the server and PERC RAID card are good because I installed Ubuntu on the logical drive (4 x 72GB disks RAID 5) no problems. I've booted frmo the Easus Todo backup CD (which is WinPE based) and recovered to the logical disk on the RAID (after installing driver inside the WinPE environment from a NAS drive) The problem is when I boot the server, I can get the OS selection menu, but any option results in a blank screen, with no errors. I figure this is probably because the driver wasn't installed on the old machine (which is IDE-based (i know, i know!) and doesn;t have a RAID controller) I've booted from the CD and copied the mraid35x.sys file to the c:\windows\system32\drivers folder on the recovered system, but it makes no difference. I made a boot.ini with rdisks 0-10 defined, and booting from each of these resulted in a file error (i.e. 'this isn't a real disk') - the only disk that gets any response (the blank screen) is multi(0)disk(0)rdisk(0)partition(1) which just gives me the blank black screen and no disk activity. Is there any way I can force the drvier to be installed on the source system (so i can do a full backup again), i've tried right-clicking the oemsetup.inf and clicking install, but it didn't actually do anything. I attempted to force it with the 'Add new hardware' wizard and forcing with the 'have disk' option but it still gave me no hardware to select. Also I've got an identical machine running WinXP which uses the PERC driver successfully (which was obviously done at install time) and the boot.ini settings are the same : multi(0)disk(0)rdisk(0)partition(1) Any ideas would be appreciated.

  Read the article

• Hard Drive problem: is it the SATA controller or the HDD itself?

  - by Drooling_Sheep

  I have a Samsung 1.5TB hard drive hooked up to an ECS H55H-I mini-ITX motherboard. I have XBMC 10 (modified Ubuntu 10.04) installed for use as an HTPC. The hard drive encounters occasional errors during normal use which cause it to be remounted read-only. I have updated the BIOS on the motherboard, changed the SATA cable and moved it to different ports on the motherboard, installed and re-installed the OS (including different versions of XBMC and generic ubuntu), all to no avail. I recently ran tests both with badblocks -sv and smartctl -t long. Both reported no errors. This makes me think the motherboard or SATA controller is probably the issue. Does anyone know of any further tests I can do to help narrow this down? The processor is a Core i3. I forget the model number but it's one of the 32nm ones with on-package graphics. There's no discrete video card or optical drive. The power supply is a 150W Rosewill (pretty sure) that came with the case.

  Read the article

• Install Peppermint OS three on Asus EeePC

  - by Kithoth

  I just had a new Asus EeePC R051CX. Out of the box, the installed OS is Ubuntu 12.04 LTS, but I am trying to install Peppermint OS three (as single boot). Problem. Once on live CD (well, live USB stick...), I'm in trouble in both following situations: Try Peppermint OS Live In this case, the first thing I get is a message reading The system is running in low-graphics mode Your screen, graphics card, and input device settings could not be detected correctly. You will need to configure these yourself. I can solely press "return" to accept, then I have a list of 4 options to answer the question "What would you like to do?". But I simply can't do anything at this moment, except switching to console mode or rebooting (keyboard / mouse controls don't allow me to do anything else). Install Peppermint OS Something I really don't understand... it launches the Ubuntu Recovery Media (which was already installed when I received the device)! Also, it says in the bottom ERROR: This recovery media only functions on Ubuntu systems. All I can do is quit (that is, reboot). One last important thing that comes to my mind: this stick worked just fine on the other computers I've tried it on. I really hope someone could bring me the light, a friend of mine told me how cool this OS is for EeePCs. Don't want to give up! Thanks. Edit I finally could install Peppermint, but not by understanding why I couldn't do it the logical way. Instead, I reinstalled Ubuntu myself (erasing the factory one). Then, I could simply boot on my live USB and perform a fresh install of Peppermint. So, I still don't know how and why the mentioned problem occurred.

  Read the article

• iptables, forward traffic for ip not active on the host itself

  - by gucki

  I have kvm guest which's netword card is conntected to the host using a tap device. The tap device is part of a bridge on the host together with eth0 so it can access the public network. So far everything works, the guest can access the public network and it can be accessed from the public network. Now the kvm process on the host provides a vnc server for the guest which listens on 127.0.0.1:5901 on the host. Is there any way to make this vnc server accessible by the ip address which the guest is using (ex. 192.168.0.249), without interrupting the guest from using the same ip (port 5901 is not used by the guest)? It should also work when the guest is not using any ip address at all. So basically I just want to fake IP xx is on the host and only answer/ forward traffic to port 5901 to the host itself. I tried using this NAT rule on the host, but it doesn't work. Ip forwarding is enabled at the host. iptables -t nat -A PREROUTING -p tcp --dst 192.168.0.249 --dport 5901 -j DNAT --to-destination 127.0.0.1:5901 I assume this is because the IP 192.168.0.249 is not not bound to any interfaces and so no ARP requests for it get answered and so no packets for this IP arrive at the host. How can make it work? :)

  Read the article

• Windows 7, network transmit (send) not working

  - by user326287

  My Win 7 works 2 years without problem. But now, I can't transmit (send) big data on LAN/Internet. I can: - Ping anything - Browse Internet, download files at full speed - Send e-mails with very small attachments. - Testing download speed on Speedtest.net, measure stable full speed. I can't: - Testing upload speed on Speedtest.net. Upload stuck.. - Save/send email messages with big (128k) attachment, independent from e-mail provider or e-mail box. THIS IS NOT A HARDWARE/CABLE/CARD OR OTHER NETWORK DEVICES PROBLEM! When I boot from a Linux Live CD, without ANY hardware change, all data sending, testing works correctly, at full speed. I have tried already in Win 7: - Disable Windows/3rd party Firewall completely - Reset IP stack parameters (netsh int ip reset c:\resetlog.txt) - Computer restore - Reinstall LAN driver When I inspect the packets in Wireshark in Windows, I see lot's of (maybe 60% of sent packets) "TCP Retransmission". Sometimes receive "TCP Dup Ack" or "TCP Out-of-Order". Linux don't do this. Thank you for the help.

  Read the article

• Can't get 1440x900 resolution with GRUB2 although vbeinfo says it's available

  - by TomSW

  I'm trying to use GRUB2 in graphical mode with 1440x900 resolution, but the result is always garbled nonsense: the highest resolution I can get is 1280x800. Word is from googling that long as vbeinfo lists a resolution, GRUB2 can use it. This doesn't seem to be true: vbeinfo says that 1440x900 is available but it doesn't work. Testing it from the GRUB2 command line: set gxfmode=1440x900 terminal_output gfxterm # -> garbled nonsense # back to trusty 640x480 terminal_output console The graphics card is an Intel GM965. Once linux boots the framebuffer switches to 1440x900. Added after epheminent's reply and various experiments vbeinfo lists two sets of modes. The first set runs from 0x160 to 0x16b, with resolutions 768x480, 960x600, 1280x800 and 1440x900 Then - after a bunch of text-only modes - the second set, containing resolutions 1024x768, 800x600, and 640x480 The first set of modes aren't altered by 915resolution. They all work except 1440x900. The resolution of modes in the second set can be altered using the 915resolution module / command available in GRUB2 = 1.99. # in /boot/grub/grub.cfg insmod 915resolution # 30, 32, 34 all work for me: all that varies is which modes are altered 915resolution 30 1440 900 # setting an impossible resolution changes the mode to "text-only" # in my case 1280x1024 is not supported 915resolution 30 1280 1024 Clearly, 1440x900 should just work: adding it with 915resolution is just a workaround.

  Read the article

• Problem with Amiga 1200 accelerator board

  - by cc0

  I just recently walked past a dump, where in the corner of my eye I spotted something that looked like a huge keyboard. I went to take a closer look, and found out that it was an Amiga 1200 with a 030 accellerator board and scala dongle. Jackpot! So anyway; I dried it, cleaned it, it works, but the floppy was not powering on and same with the harddrive. I am using an old Amiga 1200 PSU that was making some strange high pitch noise when I tried to boot the amiga with the harddrive installed in it. I removed the harddrive and it booted fine with the PSU not emitting any detectable noise. However, when I have the 030 installed it sometimes reboots and shows a red "Software Error" screen. I tried removing the memory on the board, same effect. Sometimes it does not boot at all, just gives a black screen. Someone suggested the card had problems with 3.1 roms, but this amiga has only 3.0 roms installed. Does anyone have any apparent theories as to why it seems unstable? I don't have any other Amiga parts to cross-swap with to test a lot of things, so I'd really appreciate some sound input here so I'd know what to look for in order to try fix it. And merry Christmas everyone :]

  Read the article

• Which components should I invest in.. for a backup machine.

  - by Senthil

  I am a freelance developer. I have a PC, a laptop and an old testing and file server machine. I might add one or two in future. I want to have an on-site backup machine that can handle backups of ALL these machines - file backups, MySQL backups, backup of subversion repository, etc.. When building the machine, which components should I invest more in? Examples: The cabinet should have lots of room for expansion. Hard disk size should be large. But I guess hard disk speed need not be high (?) But other components like, RAM, PSU, Processor, Network card, Cooling, etc.. how much relative importance do these have in a backup machine? Which of these components should be high-end or large, and which ones need not be? Some Idea of the load: There will TBs of data. File backups and subversion repository backups will at least be done daily. MySQL backups done weekly. assume 3 machines at the moment and somewhere around 10 machines in the future.

  Read the article

• Linux can dual display but windows can't?

  - by Mr_CryptoPrime

  I have two monitors, one that is hdmi-to-dvi and the other vga-to-dvi. I have an AMD HD Radeon 6900 series graphics card installed. I got Ubuntu to display dual monitors, but then I restarted for an update and then Ubuntu wouldn't even boot in recovery mode, it just kept cycling forever...displaying something about "timeout: killing [filepath] [hexadecimal]. So I tried booting into windows (7-professional) and it crashed and displayed this after rebooting: IRQL_NOT_LESS_OR_EQUAL, PAGE_FAULT-IN-NONPAGED-AREA. I went into Bios and reverted to the system defaults and ran system restore and it booted ok, but the dvi-to-dvi monitor would not display. I made sure my drivers were updated and catalyst was updated. Also through research discovered only one is for vga and the other is digital only, so I put the vga-to-dvi in the vga slot and so on. Neither windows or catalyst will detect the dvi-to-dvi montior. Any suggestions? Thanks. EDIT: Found out that booting into Ubuntu with only one monitor (using either monitor with either cable) worked perfectly fine. I could then add another monitor and it displays ok. However, it will, out of the blue, suddenly distort the display. At first I thought the computer crashed, but it is something with the video output from the GPU to the monitor because I pushed the power button and it would refresh every 5secs or so and I could see the "Ubuntu will power down in X seconds", even though it was horribly distorted. Any ideas what's causing this?

  Read the article

• 4GB Memory Upgrade for Acer Aspire 5102WLMi

  - by Richard Slater

  I have bought a 4GB memory upgrade (2x 2GB PC2-5300 SODIMM) for my Acer Aspire 5102WLMi (Aspire 5100 Series) laptop, I installed the two memory modules correctly however with 4GB installed the laptop refuses to POST. I have tried the following: Tried both 2GB SODIMMs without the other (Worked Fine) Tried the original 512MB SODIMMs (Worked Fine) Tried with original 512MB SODIMM and new 2GB SODIMM (Worked Fine) Tried swapping over the 2GB SODIMs (Didn't Boot) Left the computer for 10 minutes with both 2GB SODIMMs installed (Didn't Boot) Checked latest BIOS installed (No Change) The Crucial website said that the laptop supported 4GB of RAM as do several other sites through found through Google, up until now I was fairly confident this would work. Couple of questions that would be good to have answered: Question: Has anyone got an Acer Aspire 5100 Series running with 4GB RAM? Answer: Yes, I have now got one working with 3.75GB Usable, the rest is occupied utilized by the Graphics Card. Question: Any tips on getting this to work; is there a CMOS reset switch? Answer: Yes there is, if both SODIMMs are removed two very small interlocking PCB tracks are revealed. If these are shorted together with a screwdriver the BIOS will be reset. Thanks.

  Read the article

• Are these hardwares compatible?

  - by Tom Kaufmann

  I am trying to upgrade my new machine but I want to do it myself. This is my 1st attempt at building system. After carefully reading reviewing feedback and my budget I have decided to select the below listed components. Can anybody let me know are they compatible or not? Transcend 64 GB 2.5" SATA Solid State Drive Asus GeForce GTX550 1GB DDR5 ENGTX550 TI DI/1GD5 Graphics Card Seagate Barracuda 1 TB HDD Internal Hard Drive Cooler Master eXtreme Power Pro 600 Power Supply Intel Core i5 2500K Sandy Bridge 3.30 GHz 95 W 4 Core Desktop Processor Intel DX79TO Motherboard Corsair CMZ8GX3M2A1600C9 8 GB DDR3 SDRAM 1600 MHz Dual Channel Kit Desktop Memory Sony AD-7260S-ZS Internal DVD Writer - Black Cooler Master Hyper TX3 EVO Intel CPU Cooler Cooler Master Elite 335U Cabinet LG E2051T 20.1 Inch SuperSlim Monitor Is any of these hardware components incompatible with I5 2500K? If you have any other suggestions for selecting any other harwdware that can boost up my performance or lower my cost while having the same performance, please suggest. But my primary questions is whether they are compatible or not! Any help is appreciated. Thank you.

  Read the article

• How to improve network performance between two Win 2008 KMV guest having virtio driver already?

  - by taazaa

  I have two physical servers with Ubuntu 10.04 server on them. They are connected with a 1Gbps card over a gigabit switch. Each of these host servers has one Win 2008 guest VM. Both VMs are well provisioned (4 cores, 12GB RAM), RAW disks. My asp.net/sql server applications are running much slower compared to very similar physical setups. Both machines are setup to use virtio for disk and network. I used iperf to check network performance and I get: Physical host 1 ----- Physical Host 2: 957 Mbits/sec Physical host 1 ----- Win 08 Guest 1: 557 Mbits/sec Win 08 Guest 1 ----- Phy host 1: 182 Mbits/sec Win 08 Guest 1 ----- Win 08 Guest 2: 111 Mbits /sec My app is running on Win08 Guest 1 and Guest 2 (web and db). There is a huge drop in network throughput (almost 90%) between the two guest. Further the throughput does not seem to be symmetric between host and guest as well. The CPU utilization on the guests and hosts is less than 2% right now (we are just testing right now). Apart from this, there have been random slow downs in the network to as low as 1 Mbits/sec making the whole application unusable. Any help to trouble shoot this would be appreciated.

  Read the article

• Can I have a single solid state drive and a RAID array on the same machine? [closed]

  - by jaminto

  Hi- To summarize, i'm looking to use a single solid state drive as my primary drive, and two conventional sata drives in a RAID 1 configuration for data. I am trying to install 64-bit Windows 7 onto this configuration. Is this possible? Here are the details: I built a desktop that has been running 64-bit Vista on two 500Gb in a RAID 1 array for a few years. I just purchased an Intel X25-M 80Gb Sata Solid-State Drive, and was planning on using this a my primary drive, and keeping the RAID 1 array as my data drive. I added the SSD drive and in the RAID setup, configured it as a RAID 0 array of only one disk. Then, I tried to do a clean install of windows 7 64-bit, but got stuck in the "Missing driver for CD/DVD drive" black hole of selecting driver files and Windows telling me that i don't have the appropriate driver for my hardware. The missing hardware is NOT a CD/DVD drive, since i'm installing off of my only CD/DVD drive. Plus at one point i was able to point it at a driver for my raid controller, and then my hard drives magically showed up as browsable sources for finding drivers for some other unnamed device that setup couldn't recognize. After a few hours of trying drivers (this was a very slow process) i decided to reboot and look at the BIOS settings. I'm using an ASUS M2A-VM motherboard which has an ATI SB600 RAID controller on board. I switched the "On board SATA Type" setting from "SATA" to "AHCI" thinking that since AHCI is an Intel thing, this would help. Unfortunately, this abandoned my RAID configuration, and my previously mirrored drives are showing up as separate drives when i boot into my current windows installation. Am i trying to do the impossible here? Should i just buy a separate SATA/RAID PCI card and plug the SSD into that? Any help would be greatly appreciated.

  Read the article

• Routing Traffic With OpenVPN

  - by user224277

  Few minutes ago i configured my VPN server, and actually I can connect to my VPN but all trafic is going through my normal home network. On my OpenVPN application I've got an information : Server IP: **.185.***.*10 Client IP: 10.8.0.6 Traffic: 7.3 KB in, 5.6 KB out Connected: 10 June 2014 19:21:59 So everything is connected but how I can setup on windows 7 that all trafic have to go through OpenVPN network card ?? Client setting : client dev tun proto udp # enter the server's hostname # or IP address here, and port number remote **.185.***.*10 1194 resolv-retry infinite nobind persist-key persist-tun # Use the full filepaths to your # certificates and keys ca ca.crt cert user1.crt key user1.key ns-cert-type server comp-lzo verb 6 Server setting : port 1194 proto udp dev tun # the full paths to your server keys and certs ca /etc/openvpn/keys/ca.crt cert /etc/openvpn/keys/server.crt key /etc/openvpn/keys/server.key dh /etc/openvpn/keys/dh2048.pem cipher BF-CBC # Set server mode, and define a virtual pool of IP # addresses for clients to use. Use any subnet # that does not collide with your existing subnets. # In this example, the server can be pinged at 10.8.0.1 server 10.8.0.0 255.255.255.0 # Set up route(s) to subnet(s) behind # OpenVPN server push "dhcp-option DNS 8.8.8.8" push "dhcp-option DNS 8.8.4.4" ifconfig-pool-persist /etc/openvpn/ipp.txt keepalive 10 120 status openvpn-status.log verb 6 and sysctl : net.ipv4.ip_forward=1 Thank you for your time and help.

  Read the article

• Hungry hungry BIOS: why do I have less than 4 GiB of memory?

  - by Rhymoid

  I thought I had 4 GiB of memory, but just to be sure, let's ask the BIOS about that: ?: sudo dmidecode --type 20 # dmidecode 2.12 SMBIOS 2.6 present. Handle 0x000B, DMI type 20, 19 bytes Memory Device Mapped Address Starting Address: 0x00000000000 Ending Address: 0x0007FFFFFFF Range Size: 2 GB Physical Device Handle: 0x000A Memory Array Mapped Address Handle: 0x000E Partition Row Position: Unknown Interleave Position: Unknown Interleaved Data Depth: Unknown Handle 0x000D, DMI type 20, 19 bytes Memory Device Mapped Address Starting Address: 0x00080000000 Ending Address: 0x000FFFFFFFF Range Size: 2 GB Physical Device Handle: 0x000C Memory Array Mapped Address Handle: 0x000E Partition Row Position: Unknown Interleave Position: Unknown Interleaved Data Depth: Unknown Alright, 4 GiB it is. But I can't use all of it: ?: cat /proc/meminfo | head -n 1 MemTotal: 3913452 kB Somehow, somewhere, I lost 274 MiB. Where did 6% of my memory go? Now I know the address ranges in DMI are incorrect, because the ACPI memory map reports usable ranges well beyond the ending address of the second memory module: ?: dmesg | grep -E "BIOS-e820: .* usable" [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009e7ff] usable [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000dee7bfff] usable [ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x0000000117ffffff] usable I get pretty much the same info from /proc/iomem (except for the 4 kiB hole 0x000-0xFFF), which also shows that the kernel only accounts for less than 8 MiB. I guess 0x00000000-0x7FFFFFFF is indeed mapped to the first memory module, and 0x80000000-0xDFFFFFFF to part of the second memory module (a bunch of ACPI NVS things live between 0xDEE7C000 and 0xDEF30FFF, and the remaining 16-something MiB of that range are just 'reserved'). I guess the highest 0x18000000 bytes of the second memory module are mapped above the 4 GiB mark. But even then, there are two problems: 128 MiB (0x08000000 bytes, living somewhere between 0xE0000000 and 0xFFFFFFFF) are still completely unaccounted for. To note, my graphics card is on PCI-Express and (allegedly) has 1 GiB dedicated memory, so that shouldn't be the culprit. Did the BIOS screw up in moving the memory, leaving it partially shadowed by MMIO? Even with this mediocre explanation, I only 'found' 128 MiB. But /proc/meminfo is reporting a much larger deficit; where's the other 146 MiB? How does Linux count MemTotal?

  Read the article

• Server specification recommendation

  - by foo

  To cut the story short, I can't buy an item (server/cpu/motherboard/ram) that costs more than USD 330. However, I can combine them, meaning, I can buy a CPU that costs USD 330 and motherboard that costs USD 330. With this limitation, I can't buy a powerful 1U server which will definitely costs me more USD 330. With that in mind, I was hoping to build a powerful desktop PC which will be used as a database server. However, through my experience, desktop PC doesn't last very long, usually the motherboard will just die by itself after 1 or 2 years. So, what would you guys recommend me to buy with this kind of budget? Every item must be <= USD 330. Will be used as a MySQL server. RAID would be nice. 1TB is pretty big for my data. I do not need external graphic card (onboard would do just fine), mouse, keyboard, monitor. Linux friendly. One ethernet port is good enough. It's important that those hardware is made of components that will last long (at least 3 years or something). The server will be placed in an air conditioned room, but a good ventilation for the server is always preferred. I won't overclock it. Intel processor is preferred. Thanks in advance.

  Read the article

• Grub Autostart with timeout

  - by BetaRide

  On Ubuntu 10.4 LTS I want Grub to start the default OS after 5 Seconds. I'd like to see the output of the startup scripts. Currently grub wait forever until I hit return and the output of the startup scripts isn't visible. Can someone tell me how I have to configure /etc/default/grub or any other setups? I tried to play with GRUB_TIMEOUT and GRUB_DEFAULT and did a sudo update-grub afterwards, but nothing changed. Any ideas? # If you change this file, run 'update-grub' afterwards to update # /boot/grub/grub.cfg. GRUB_DEFAULT=0 GRUB_HIDDEN_TIMEOUT=5 #GRUB_HIDDEN_TIMEOUT_QUIET=true GRUB_TIMEOUT=5 GRUB_DISTRIBUTOR=`lsb_release -i -s 2> /dev/null || echo Debian` GRUB_CMDLINE_LINUX_DEFAULT="quiet splash" GRUB_CMDLINE_LINUX="" GRUB_SAVEDEFAULT=true # Uncomment to disable graphical terminal (grub-pc only) #GRUB_TERMINAL=console # The resolution used on graphical terminal # note that you can use only modes which your graphic card supports via VBE # you can see them in real GRUB with the command `vbeinfo' #GRUB_GFXMODE=640x480 # Uncomment if you don't want GRUB to pass "root=UUID=xxx" parameter to Linux # GRUB_DISABLE_LINUX_UUID=true # Uncomment to disable generation of recovery mode menu entries #GRUB_DISABLE_LINUX_RECOVERY="true" # Uncomment to get a beep at grub start #GRUB_INIT_TUNE="480 440 1"

  Read the article

• Windows 7 host with Ubuntu Guest and a performance hit, memory locks?

  - by Cyrylski

  I have a brand new Lenovo T510 with Core i5 and 4GB of RAM with Windows 7 on it. I Installed Ubuntu 10.10 in a Virtualbox. For some reason system gets really slow on this setup which makes me really angry. There's a video card shared with full 3D support enabled and 1GB of RAM allocated for the Ubuntu machine. It may sound stupid, but WHY is the whole memory consumed in an instant when I run Virtualbox? I struggled for like 10 minutes restraining myself from a brutal reset, and now everything runs smooth but memory "in use" in Resource Monitor is 3GB flat with only Chrome running. I'm new to Windows 7, but I'm really disappointed with performance at this point... I used to work in a different environment with much slower hardware and there was no such problem (WinXP over Ubuntu, 1GB out of 2GB allocated for WinXP guest on intel GMA). This is, until I clogged RAM totally there. But I was capable of running Chrome, Firefox and Apache server on a 1GB RAM in Ubuntu there and Photoshop CS4 on Windows XP and it worked. In this case I can't go beyond setting up Ubuntu properly. I bet I'm doing something wrong.

  Read the article

• Can't connect to wi-fi hotspot in Ubuntu 11.10

  - by ht3t

  I'm new to Ubuntu. I'm having a wireless network problem in Ubuntu 11.10. I made a hotspot using Connectify from a computer which is running Windows 7. I can access it in Windows 7 but not in Ubuntu 11.10. Every time I access it,I get a message "disconnected". I'm using msi fx 400 notebook with Intel Centrino wireless -N 1000 wireless card. Ubuntu version is 11.10 with KDE desktop. $ sudo lshw -c network [sudo] password for ht3t: *-network description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:06:00.0 logical name: wlan0 version: 00 serial: 00:26:c7:56:b8:f0 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=3.0.0-12-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:44 memory:e7400000-e7401fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:07:00.0 logical name: eth0 version: 06 serial: 40:61:86:b6:b1:a2 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-2.fw IP=192.168.21.107 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:41 ioport:9000(size=256) memory:e6004000-e6004fff memory:e6000000-e6003fff I can't do anything without internet connection. How can I fix this?

  Read the article

• p410i Mirror failed couldnt find same disk

  - by Heishiro Mitsurugi

  I have an HP server with an P410i RAID Card installed. I had two SATA Drives connected (250GB each). The RAID was configured as a Mirror. A few days ago the drive one (1) failed, and i had to remove it. Tried to find the same part number here in Venezuela, but i couldn't. So, i bought a 500GB SATA Drive, and connected it to the same bay where the 250GB failed drive was. When the server booted, it asked me if i wanted to rebuild the data. I selected the option for that, and Windows Server restarted properly. When i got into the ACU (Array Configuration Utility) it told me that it was rebuilding the data. Today the warning went away, and according to the ACU everything is just fine. My question is... What i did was right? Can i create a mirror from a 250GB disk in a 500GB disk using the p410i? I have done that before, but only using software RAID in Windows, and it just uses the space it needs. As a matter of fact, when did that using Windows i was able to use the remaining space in the bigger drive, but in the p410i i can't use it. Should i be worried? Thanks a lot in advance for any pointers or info that you could give on this. Heishiro

  Read the article

• My Hard Drive isn't Working

  - by MeCB

  I never use Safely Remove Hardware with Windows XP. It has been working for me for years with my SD card, mouse, hard drive and memory stick. My hard drive has a USB cable and power cord so I can hook it up to any desktop hard drive. Now my hard drives don't like this and I did not know this till now. I am always careful and to wait till it is all finish accessing the USB before I unplug it. Now three of my hard drives can't be seen by Windows, though the others still work. when I hook it up to another computer it works fine. I use the same USB cable to hook up all of my hard drives one at a time. So my USB cable is good. I think that when I unplugged the hard drive this one time, it had a file it still wanted to see and now only this drive does not work only this computer. Then the same thing happens to my other two hard drive after I used it for a week with the same cables. How can I fix this?

  Read the article

• What can cause the system to freeze in a way where even the reset button takes a long time to react?

  - by ThiefMaster

  What can be the reason for system freezes that are so "hard" that even the hardware reset button takes about 3 seconds until it actually resets the system (and then it actually powers down and up again instead of doing a "clean" hard reset like when pressing it during a normally running system). Since it initially happened mainly while playing videos from YouTube I suspected the graphics card - however, I replaced it recently and it did not change it. It still happens from time to time (and sometimes more often, like a few times times in the last few hours). The system is running Windows 7 - but I don't think this matters since I don't think any software, not even the OS, can actually affect the reset button's behaviour. The PC is not overheated and the freezes happen randomly. There is also no malware on the system. The CPU is an Intel Core i7-920 on a Gigabyte EX58-UD5 mainboard. What could be the cause for this problem? Faulty RAM? I did not run a full memtest86 check yet, but I wonder if there is a more likely issue than faulty RAM - checking 12G of ram does take some time after all! There are no entries in the event log - but that's what I expected since the system freezes so hard that I doubt it has time to write anything to any log.

  Read the article

• What could cause a dual-monitor PC to suddenly stop using one of the screens?

  - by raldi

  I've got a dual-monitor setup using a GeForce 7900GT that was working fine for over a year... then suddenly, only one of the screens works. It's not OS-related, because even on startup, only one screen displays the BIOS checks. In the past, both screens would show it together. I didn't change anything to trigger this The monitor that gets a signal is random -- sometimes the one on the left goes black, sometimes the one on the right. The monitors and their cables are good -- I can switch both or either, and I get a signal just fine. They're plugged in, too. It's not the video card, either -- I have an identical 7900GT in another machine, and swapping the two didn't fix anything. It's not dust on the motherboard -- I pulled everything out, cleaned it off, checked for obvious damage, put it all back together, and no change. My next two steps are going to be to reset the CMOS info and to try swapping out the motherboard. Before I do that, does anyone have any other ideas?

  Read the article

• ZFS Data Loss Scenarios

  - by Obtuse

  I'm looking toward building a largish ZFS Pool (150TB+), and I'd like to hear people experiences about data loss scenarios due to failed hardware, in particular, distinguishing between instances where just some data is lost vs. the whole filesystem (of if there even is such a distinction in ZFS). For example: let's say a vdev is lost due to a failure like an external drive enclosure losing power, or a controller card failing. From what I've read the pool should go into a faulted mode, but if the vdev is returned the pool should recover? or not? or if the vdev is partially damaged, does one lose the whole pool, some files, etc.? What happens if a ZIL device fails? Or just one of several ZILs? Truly any and all anecdotes or hypothetical scenarios backed by deep technical knowledge are appreciated! Thanks! Update: We're doing this on the cheap since we are a small business (9 people or so) but we generate a fair amount of imaging data. The data is mostly smallish files, by my count about 500k files per TB. The data is important but not uber-critical. We are planning to use the ZFS pool to mirror 48TB "live" data array (in use for 3 years or so), and use the the rest of the storage for 'archived' data. The pool will be shared using NFS. The rack is supposedly on a building backup generator line, and we have two APC UPSes capable of powering the rack at full load for 5 mins or so.

  Read the article

• System requirements for running windows 8 (basic office use) in virtualbox (ubuntu as host os)

  - by Tor Thommesen

  I want to run windows 8 as a guest os with virtualbox on some thinkpad (haven't bought one yet) running Ubuntu 12.04. Apart from virtualizing windows 8 (mostly just for use with the office suite app) my needs are very modest, I don't need much more than emacs and a browser. What I'd like to know is what kind of specs will be necessary to run windows 8 well as a vm, using the office apps. It would be a shame to waste money on overpowered hardware. Are there any official guidelines from oracle or windows on this? Would this lenovo x220, for example, be sufficiently strong? The specs below were taken from this review. Intel Core i5-2520M dual-core processor (2.5GHz, 3MB cache, 3.2GHz Turbo frequency) Windows 7 Professional (64-bit) 12.5-inch Premium HD (1366 x 768) LED Backlit Display (IPS) Intel Integrated HD Graphics 4GB DDR3 (1333MHz) 320GB Hitachi Travelstar hard drive (Z7K320) Intel Centrino Advanced-N 6205 (Taylor Peak) 2x2 AGN wireless card Intel 82579LM Gigabit Ethernet 720p High Definition webcam Fingerprint reader 6-cell battery (63Wh) and optional slice battery (65Wh) Dimensions: 12 (L) x 8.2 (W) x 0.5-1.5 (H) inches with 6-cell battery Weight: 3.5 pounds with 6-cell battery 4.875 pounds with 6-cell battery and optional external battery slice Price as configured: $1,299.00 (starting at $979.00)

  Read the article

< Previous Page | 204 205 206 207 208 209 210 211 212 213 214 215  | Next Page >