Search Results

Search found 7118 results on 285 pages for 'sam ram san'.

Page 209/285 | < Previous Page | 205 206 207 208 209 210 211 212 213 214 215 216  | Next Page >

• Will my RAID0 stay intact when I move it to a new computer?

  - by Jeremy H

  My primary drive is a 250GB WD SATA drive. So, I added 2x 500GB 7,200 RPM WD SATA drives into my Windows Vista box and created a 1TB RAID0. I then formatted the the primary drive and installed Windows 7. To my pleasant surprise when I booted into Windows 7 my RAID0 was still intact and I kept trotting along the same as I did before. Now I am replacing my motherboard, processor, and RAM and plan on formatting the primary 250GB drive again and using it to boot for a new clean install of Windows 7. My question is: if I move these two SATA drives which are setup for RAID0 into the new system, install Windows 7 again, will the RAID0 remain? Edit: Software RAID. I created it within Windows. The RAID0 does NOT contain the system boot partition.

  Read the article

• ESXi 5.1 - Unable to register host

  - by deanvz

  I download and successfully installed ESXi 5.1. I am however unable to get the licence key I received installed. An error occurred when assigning the specified licence key: The system Memory is not satisfied with the 32 GB of Maximum memory limit. Current with 80.00 GB of Memory. Is there now way around this? A quick google revealed that this is a global problem with no real answer or resolution. The only workaround is to remove the physical RAM chips, but as this is in going to be in production I dont want to do that as it would mean down time when I have to reinsert the memory

  Read the article

• Another "Trouble copying music files from HD to 16GB thumb drive"

  - by Ron

  I have a brand new HP Quad Core - 6GB Ram - running 64-bit Windows 7. Running Norton Internet 2010. I try copying music files from HD to 16 GB thumbdrive and get blue screen after a few files have transfered over to thumbdrive. Computer blinks once and boom - blue screen and then reboots. This is really aggravating. I stopped anti-virus, pulled other USB attached devices - still does same thing. Any solutions out there?

  Read the article

• Windows 7 - Windows 8 dual boot installation error

  - by Nikhil

  I am trying to dual boot Windows 8 with Windows 7 . But I keep getting an error while selecting the drive to install on . The error is ""Setup was unable to create a new system partition or locate an existing system partition. See the Setup log files for more information." " . What might be the problem ? Also previously I tried to install only Windows 7 on my HDD . I downloaded the ISO from digital river . Made bootable usb . I got the same above error . But when I tried to install it via other usb which had pirated Windows 7 downloaded from torrents it gave no error . My system config is Motherboard - Gigabyte G41 MT S2P HDD - 160 GB SATA RAM - 8 GB Help !!!

  Read the article

• Server not responding to SSH and HTTP but ping works

  - by yes123

  Hello guys, I requested an hard reboot because none of ssh and http worked. Ping worked normally. Which logs should i check to understand what was the problem? Thanks! (debian 6 on lamp) Edit: my memory and swap: Mem: 4040068k total, 1114920k used, 2925148k free, 109212k buffers Swap: 1051384k total, 0k used, 1051384k free, 283820k cached 4 GB ram (and more than 1TB of HDD) The cause is from 2 days ago: look how the usage of swap goes +60% in less than 10hours My control panel reports this as top 5 memory usage process: If every apache2 process is 190MB large that sux because IF i do TOP i have 262 sleeping process most of them are apache2! My apache mpm_prefork settings are: <IfModule mpm_prefork_module> StartServers 5 MinSpareServers 5 MaxSpareServers 10 ServerLimit 1500 MaxClients 1500 MaxRequestsPerChild 2000 </IfModule> KeepAlive On MaxKeepAliveRequests 100 KeepAliveTimeout 4

  Read the article

• Virtual MS Sql Server not consuming enough CPU

  - by rocketman

  We have a Win2008 server 32 bit running as a virtual machine under ESX server. It has 6 CPU cores of 2Gz each and 4GB ram. It's running MS Sql Server 2008 R2 only. Problem: The server is heavily loaded and responds slowly. From windows taskmanagers point of view, it really looks overloaded, CPU wise. However, our external "cloud manager" says it's only using 2.5GHz worth of CPU-cycles in the cluster. I/O times looks "good". We have already tried to set the SQL servers number of working threads from 0(auto) to 256, to no effect. How to tune the VM host, guest or SQL to use all of it's alotted resources? Does it sound possible att all?

  Read the article

• File corruption

  - by firesoul

  Recently, almost every file I try to copy into my HDDs gets corrupted. When writing to the disk, some portion of the file is replaced by random bytes (Checked using Diff apps) There's no problem reading existing files. I'm pretty sure it's not the HDD, becasue I've tried another HDD (a brand new 1TB WD) and the problem still remains. I have an AMD Athlon 64 X2 CPU, an ASUS M2NE motherboard, 2 WD SATA II HDDs (320GB + 1TB) and 3GB of Corsair RAM. My OS is Windows 7 (64 bit) Now, what could be the cause of this? If it's the motherboard, can it be fixed by using a PCI SATA card?

  Read the article

• Why is process not being displayed by TOP

  - by drN

  I am running a Mathematica script (this question probably doesn't fit in Mathematica.SE however) and I know that it generally takes up a lot of RAM and loads up my cores. However, althought pgrep MathKernel is showing a pid, I find that top doesn't show this in the top processes, although I notice that it is taking up about 2.25GB of the 8GB available to me. pmap -x my_process_id total kB 2243132 1907404 1892108 AND ps aux | grep MathKernel dnaneet 20837 12.6 23.3 2234944 1907404 pts/1 Sl 09:23 8:01 /share/apps/mathematica/8.0.4/SystemFiles/Kernel/Binaries/Linux-x86-64/MathKernel -runfirst $TopDirectory="/share/apps/mathematica/8.0.4" -script ./dcm_10micrometer_2x -- ./dcm_10micrometer_2x ps aux shows that the process is taking about 12% (In asterisks) dnaneet 20601 0.0 0.0 68264 1660 pts/1 Ss 09:15 0:00 -bash **dnaneet 20837 12.2 23.3 2234944 1907404 pts/1 Sl 09:23 8:01 /share/apps/mat** dnaneet 21922 0.0 0.0 65604 948 pts/1 R+ 10:29 0:00 ps -aux Did this process fail and is the MathKernel just lingering?

  Read the article

• How do I change the NGINX user?

  - by danielfaraday

  I have a PHP script that creates a directory and outputs an image to the directory. This was working just fine under Apache but we recently decided to switch to NGINX to make more use of our limited RAM. I'm using the PHP mkdir() command to create the directory: mkdir(dirname($path['image']['server']), 0755, true); After the switch to NGINX, I'm getting the following warning: Warning: mkdir(): Permission denied in ... I've already checked all the permissions of the parent directories, so I've determined that I probably need to change the NGINX or PHP-FPM 'user' but I'm not sure how to do that (I never had to specify user permissions for APACHE). I can't seem to find much information on this. Any help would be great! (Note: Besides this little hang-up, the switch to NGINX has been pretty seamless; I'm using it for the first time and it literally only took about 10 minutes to get up and running with NGINX. Now I'm just ironing out the kinks.)

  Read the article

• Getting BootMgr not found errors repeatedly on Win7 x64

  - by abszero

  So here is the basic configuration of the box: Primary RAID 1 (Mirror, Bootable): 2x 300GB WD SATA drives AMD Phenom Quad Core x64 @2.2 ASUS M3N78 Pro Board 4GB RAM Win 7 Ultimate Additionally, this box is a Host OS for several CentOS Boxes via VirtualBox. The box runs like a champ but, for whatever reason, everytime I restart the machine I get a BootMgr not found error when the box tries to boot. I pop in my Win DVD, select 'Repair Windows' then 'Fix Start Up Problems' and everything works fine...once. When I restart the box again I have to go back through this process. Any ideas on what is going on?

  Read the article

• Outlook Express hangs when selecting multiple emails

  - by Javier Badia

  I'm using Outlook Express (6, I think) on Windows XP. Lately, it has been hanging. Sometimes this happens at startup (right after the main window with all the panes loads) and sometimes when selecting many emails (sometimes as low as three emails at once, sometimes at ten, it's not a fixed number). When this happens, msimn.exe starts to use 98-100% CPU and RAM usage shoots up very quickly, reaching hundreds of megabytes in half a minute. The message pane goes gray instead of showing the message contents. As I said, this sometimes happens right after the main window loads, sometimes when selecting many emails at once. I tried backing up everything, deleting the identities, creating a new one and restoring, but this still happens.

  Read the article

• No display but video card fans spins

  - by Marc

  Since I moved my computer there's no display when I plug my screen in the video card but works fine in the mother board. I tried reseting the cmos, but I still have the same problem. The fans are spining and there's a light from the card. I tried the DVI ports and the HDMI Here's my build. I have it for 2 months and everything was working fine. Do you think it's the video card? Asus p8z68-v pro gen3 Intel i7 2600k 120 GB OCZ Agility 3 16 GB RAM Blue Corsair DDR3 Asus GTX 570 H80 Corsair liquid cooling XFX PRO750W 80Plus bronze power supply EDIT That's why And I can't push more cause the card is on this Thank you everyone! I fixed it by pushing the mobo from the other side of the case and now it fits.

  Read the article

• Xen Disk Performence Issues

  - by user98651

  I'm currently using Xen PV on CentOS 5 with my domU's as flat files running on a hardware RAID controlled (write cache enabled) formatted with XFS. On the dom0 I can get about 500MB/s in a 2GB dd write from /dev/zero however on the domU's I'm lucky if I get 10MB/s (it is usually around half that). I've tried changing the disk scheduling to NOOP on the domU's, changed some mount parameters and tweaked the performance allocations of both the dom0 (prioritize CPU) and domU's (increase RAM and VCPU allocations). None of these steps have produced any noticeable change in performance. My instinct here is that it is not a hardware problem, due to the solid performance of the dom0. Any ideas on what might be causing this problem? I'm considering moving to LVM based domU's.

  Read the article

• Windows 7 clean install, freezes when starting programs

  - by madmaze

  Hello Everyone, I have a problem on a brand new Windows 7 Lenovo T510 intel I5/4gb ram. When I got the Laptop, right off the bat i noticed that it would freeze up often on th most simple tasks. After a while I got fed up and reinstalled. All that is installed currently is AVG/Firefox/Office. I Rebooted after installing those things and when I try to open Firefox it freezes just trying to open. Ive tried a few other things and it freezes all the time. Any Ideas what it could be?

  Read the article

• Browsing is much slower on one PC wired to the same router - why?

  - by deanalt

  Wife is not happy. It takes about 5 seconds to open a google window, versus about 1 second on the faster computer which is about 3 years old itself. Yes, it is an older computer (5 -6 years old, I'd guess), surely with less RAM, but for simple browsing, should it matter? Both are hardwired to the same Netgear Rangemax router. Both use fixed IP addresses. Both are XP. Both have about 8 feet of cable to the router. I have the fastest service my cable provides. Probably irrelevant but ...two newer MACs are connected wirelessely during the summer and they are even faster, but I think that's the difference in browsers. If you could point me to a list of process of elimination steps that would be most appreciated. Thanks Dean

  Read the article

• Is a PCIE X1 card for USB 3.0 worth it?

  - by lelouch

  I have a portable HDD on USB 3.0, and soon I'll have a 32gb flash drive on USB 3.0 as well. My motherboard is pretty old - and the next time I'll upgrade it is when I get a new CPU/mobo/ram. Slots on my mobo: PCIE X16 - For my GTX 260 2xPCI PCIE X1 I'm considering purchasing a PCI express X1 card like this - http://www.ebay.com.au/itm/PC-Laptop-2-USB3-0-Ports-PCI-E-PCI-Express-X1-Card-New-/280772000446?pt=AU_Networking&hash=item415f50babe Now the question: What are realistic (read/write) speeds I'll get in this setup, assuming I have 1 USB 3 device connected at a time, and the bottleneck is the PCIE?

  Read the article

• How to minimize services in ubuntu

  - by codeomnitrix

  Hello everyone.I am using ubuntu from last 6-7 months. I am having 512mb ram and a p4 processor with 1.73 Ghz processing speed. And being a programmer i have to work with eclipse and netbeans like ide's, and they sometimes hang. So is there any option in ubuntu to stop the services running just like i do have in windows "msconfig" or mycomputer-manage, and where could i find the details about the services so that i should know what will be its effect if i stop this service. I am using ubuntu 10.10 Thanks

  Read the article

• recommendations for a lightweight linux distribution for a test server

  - by Jack

  I'm planning on setting up a test server to experiment with some application servers (tomcat/jboss/...) and with some portals. Now the machine I've set aside for this is lightweight CPU/GPU wise(Atom D510, 4 gigabyte ram, 500 GiB hdd, onboard GPU). But it should suffice for most things, I'm more interested in the stability of JBoss/Tomcat for my purposes than the stability. However I'm having a bit of trouble picking an appropriate distribution size/performance/setup time wise/security wise since it seems I can't sneeze without another distribution popping up. I've been thinking about going for Fedora since I've read that that distribution has been optimized for Atom, but I'm not really familiar with it. My experience with Linux has mostly been limited to Ubuntu and some tinkering with puppylinux. I'm not afraid to get my hands dirty using the command line. I'm not planning on starting a discussion per se, mostly the pros/cons that people have encountered with some distributions

  Read the article

• Dell Windows 7 DVD includes IE9, where to find IE8?

  - by mjmcinto

  It appears as though we can now only get a 64 bit installation of windows 7 to come with IE9, and I cannot find an installer for IE 8 for it. This presents a problem, as I am building a new machine for a developer, but the company does not support IE9 yet, and all development needs to be able to be run on IE8. I would rather have them on a 64 bit version of windows so they can have more than 4GB of RAM (can get IE8 on 32 bit win 7). Does anyone know how to get IE 8 on a new 64 bit version of win 7?

  Read the article

• Google Chrome gets really slow on 10+ open tabs

  - by Anton

  For some time already I face a problem with Google Chrome. I really love this browser, but on Windows 7 on a pretty decent machine (i5, 4GB RAM) it gets REALLY slow when I open for instance 10 techcrunch.com pages. Once I do that it becomes virtually difficult to scroll through pages and the general responsiveness of the browser gets down. And if I open 20+ or 30+ tabs there is a good chance all of them will crash. Does anyone got an idea? This happens to me on several PCs with Windows 7 64bit. At 10 tabs there is 600-700MB memory used by Chrome. Two systems have the issue are both laptops with integrated graphics. One by Intel, the other an nVidia GeForce 310M.

  Read the article

• ideal memory configuration 4 bank, ddr3, AM3+ FX - 1 vs 2 vs 4 dimms?

  - by TardisGuy

  Ok, so ive been looking around, trying to learn and understand the way that ram works. Ive gotten one answer that said "The addressing is best for 2 sticks, and when you use 4; it slows down" Another answer said something like: Theres bank/channel interleave that makes the memory read like one stick Also I read something about the memory density also being a factor. I dug further and found out that theres a higher speed limit on my board for 2 sticks vs 4, so now im trying to put an image in my head of how and why, and... pfft. Can anyone explain, or recommend a resource that would answer these questions?

  Read the article

• slow disk writes between host and guest

  - by Jure1873

  I've got a ubuntu (server kernel) on a amd x4, 4gb ram, 2x seagate sata 1 tb disks for testing virtual machines and the write performance is very slow. The two disks are in a software raid1 array, one small boot ext3 partition, 10gb system partition and the rest is a xfs partition (about 980) gb for data (virtual machines). If I'm copying files from the virtual machine to the host with rsync or scp the copy frequently stalls or goes at about 1mb/s. What's wrong? I've tried disabling barriers on xfs, increased logbufs, allocsize, but it seems nothing helps. The strange thing is that await (for example during copying) for sda is usually under 100, while for sdb is around 400. Any ideas on what could be wrong / what could I do to improve this setup?

  Read the article

• Testing a Virtualisation of a Debian Server (vmWare vSphere probably)

  - by xyza

  I'm soon getting access to a powerful root-server (quad-core, 16gb ram, 1gbit connection) where gameservers (like minecraft,counterstrike etc.) for different customers should be setup. My plan is to use programs such as vmWare vSphere to create some virtual machines for each customer. Inside such a virtual machine I'll setup the gameserver and maybe some kind of ftp server when its needed. Now that I'm kinda new to virtualisation of servers I want to test this local on my Desktop Computer. Is it possible to create a virtual machine of debian using vmWare Player on my Windows desktop computer and then install vmware vSphere in this VM to create multiple VM's inside that VM ? Or do I really need to install Debian on my desktop computer. (I want to use the time during installations etc. to work a bit at my windows installation) Some tips on virtualising debian servers are also appreciated :)

  Read the article

• Upgrading from 32 to 64 Bit Windows 7, without losing program installations/games

  - by Fogest

  I recently built a new computer and put the wrong installation of Windows on (32 bit), meaning I cannot use all of my RAM. I would like to upgrade to the 64 bit version, though I already have downloaded many programs and games which would total to around 30 GB give or take. I don't have the kind of data usage with my ISP to re-download this much data again, until next month (total GB will be higher as time goes on). I know there is Windows Easy Transfer, but it is not so much my data itself I'm worried about, it is more having to re-download and install a bunch of games and applications. Is it possible to perform an upgrade from 32 bit to 64 bit without this loss?

  Read the article

• HDD not detected whenever first power on (detected at BIOS level)

  - by Alvin Lim

  I am using Asus P8H61-M LX Motherboard with latest version of BIOS: 4401 One SATA-3 Western Digital Black Series 1.5TB is attached to SATA port 0 A Samsung 22x DVDRW SATA drive attached to SATA Port 1. ps/2 Logitech mouse and keyboard. CPU is i3 with DDR3 8Gb RAM. no other devices are installed. My problem is that when I turn on the computer, the WD HDD is not detected. ie cannot be booted. I have to press ctrl+alt+del in order to get it detected. I'd used the WD data lifeguard software to scan the HDD, the smart status is OK, the surface scan does not show any error at all. Where did I do wrong? Any advice is greatly appreciated.

  Read the article

< Previous Page | 205 206 207 208 209 210 211 212 213 214 215 216  | Next Page >