Search Results

Search found 6432 results on 258 pages for 'wireless adapter'.

Page 209/258 | < Previous Page | 205 206 207 208 209 210 211 212 213 214 215 216  | Next Page >

  • Disabling networkmanager for a specific interface

    - by bdonlan
    I'd like to do some experimentation with hostap without disabling my primary wireless interface. How do I tell networkmanager to keep its hands off a specific interface or interfaces while allowing it to continue managing all other interfaces normally? I'm using Ubuntu 9.04. (Wasn't sure if this should go on superuser or serverfault, as networkmanager isn't much of a 'server' tool - if it belongs on serverfault please feel free to move it) Edit: I've tried adding this to /etc/network/interfaces: allow-hotplug wlan2 iface wlan2 inet static address 192.168.49.1 netmask 255.255.255.0 But this has no apparent effect, even after restarting NetworkManager. Here's my /etc/NetworkManager/nm-system-settings.conf: [main] plugins=ifupdown,keyfile [ifupdown] managed=false Edit[2]: Looks like I needed to restart nm-system-settings, then NetworkManager.

    Read the article

  • Seasgate GoFlex NAS + Horrible Speed = Bad Experience

    - by Jon H
    I am having issues with transfer speeds from my desktop PC to my NAS. I have my NAS hooked up to a Gigabit Gateway as well as my Desktop with Cat 5e. I see up to 4.0 MB/Second Transfer Rates, the normal is about 2.5 MB/Seconds. There is 3 Partitions on my NAS, Public, Private, Backup. When I transfer from Private to Public I see the speeds above. If its under the same partition almost instant. I was wondering if the speeds I am seeing is in due to my Computer or the NAS. I was looking into building my own Media Server in due to these horrible speeds. Is their anything I can do in the mean time to speed this up? Motherboard = M3970AM-HP (Angelica) Processor = AMD FX 6100 Ram = 10GB PC3-10600 MB/sec Hard Drive (1) = 1.5TB SATA 3.0GB 5400RPM Hard Drive (2) = 120GB SATA SSD NAS = Seagate 3TB Go Flex Home Connection (1) = 1000 Base T Connection (2) = Wireless N

    Read the article

  • wireshark not seeing all packets on WiFi

    - by Caffeine Coma
    I'm using Wireshark on OSX, trying to sniff my home network over WiFi. While I can see packets that are sent to/from the host I'm sniffing on, I'm not seeing anything else that goes over the WiFi. It's like I'm not in promiscuous mode or something (the promiscuous mode box is in fact checked). The router is an Apple Airport Extreme, protected by WPA2. I'm attached to the network I'm trying to sniff, so I'm confused about why I can't see other traffic. Edit: I solved this by the following: Plug Macbook directly into the Airport Extreme router Enable "internet sharing" on Macbook, with no password. Bind wireless device (the one I wanted to sniff) to the WiFi hotspot generated by Internet sharing in step 2. Run Wireshark on the Macbook, bound to device en1. Don't forget to disable sharing after you're done. :-)

    Read the article

  • abstract class MouseAdapter vs. interface

    - by Stefano Borini
    I noted this (it's a java.awt.event class). public abstract class MouseAdapter implements MouseListener, MouseWheelListener, MouseMotionListener { .... } Then you are clearly forced to extend from this adapter public class MouseAdapterImpl extends MouseAdapter {} the class is abstract and implements no methods. Is this a strategy to combine different interfaces into a single "basically interface" ? I assume in java it's not possible to combine different interfaces into a single one without using this approach. In other words, it's not possible to do something like this in java public interface MouseAdapterIface extends MouseListener, MouseWheelListener, MouseMotionListener { } and then eventually public class MouseAdapterImpl implements MouseAdapterIface {} Is my understanding of the point correct ? what about C# ?

    Read the article

  • How to leverage Spring Integration in a real-world JMS distributed architecture?

    - by ngeek
    For the following scenario I am looking for your advices and tips on best practices: In a distributed (mainly Java-based) system with: many (different) client applications (web-app, command-line tools, REST API) a central JMS message broker (currently in favor of using ActiveMQ) multiple stand-alone processing nodes (running on multiple remote machines, computing expensive operations of different types as specified by the JMS message payload) How would one best apply the JMS support provided by the Spring Integration framework to decouple the clients from the worker nodes? When reading through the reference documentation and some very first experiments it looks like the configuration of an JMS inbound adapter inherently require to use a subscriber, which in a decoupled scenario does not exist. Small side note: communication should happen via JMS text messages (using a JSON data structure for future extensibility).

    Read the article

  • Salting example in Zend Framework

    - by Geoffrey
    Hello all, I am pretty new to the Zend framework and looking to build an application with pretty tight password security. I have been trying to follow the user guides in relation to password salting but haven't had any luck so far. I have setup my database and table adapter (As described in the documentation on the Zend Framework site but it didn't seem to finish the example (or I am not following well enough!) I have started with: $authAdapter = new Zend_Auth_Adapter_DbTable($dbAdapter, 'users', 'username', 'password', "MD5(CONCAT('".Zend_Registry::get('staticSalt')."', ?, password_salt))" ); But from here, what is done with the password salt? I just need an example and I'll be away! Does anyone have an example or point me in the right direction?? Many thanks!

    Read the article

  • How can I make a vpn network login the default behavior for logging into Windows?

    - by Danny
    To login to the machine, I have to login to our domain. When I am at work, the unauthenticated wireless permits access to the domain. However, the internet is not available until I connect via the vpn. From home, I have to connect via the vpn first, then I can login to the domain. I have successfully setup a network logon with the vpn (following the directions found here). And for the most part it works correctly. (There is an issue with logout/login I haven't figured out just yet). As I currently have to Switch User and select the Network Login button, I'd like to know if it is possible to have the network login the default behavior when logging into the system. This is mostly a usability issue than anything else.

    Read the article

  • trouble with internet connection - slow to open web pages if they open at all until I put VPN on and then they open ok

    - by Caroline Coleman
    I am having problems with my internet connection. At the moment I am on a mac and connected through a netgear wireless router. The internet connection either won't open a webpage at all or if it does it takes ages. However if I turn my VPN on the pages open at a normal speed. Also skype functions OK and I seem to be able to download files ok. I have tried connecting with a wire between the router and the computer and it makes no difference.

    Read the article

  • Why is my connection to Playstation Network so unreliable? [closed]

    - by jammus
    Hello friends. I'm 28 and my girlfriend is 24. Our home internet connection is pretty reliable, it's almost always up and can get fairly high download speeds. However, my experience with the Playstation Network is pretty frustrating. I'm always getting kicked off or getting quite high latency. Are there any tips or tricks that you might help my on-line gaming run more smoothly? I'm using a wireless connection for the PS3, is this likely to affect things?

    Read the article

  • LinkSys WRT54GL + AM200 in half-bridge mode - UK setup guide recommendations?

    - by Peter Mounce
    Crossposted from here I am basically looking for a good guide on how to set up my home network with this set of hardware. I need: Dynamic DNS Firewall + port-forwarding VPN Wake-on-LAN from outside firewall VOIP would be nice QoS would be nice (make torrents take lower priority to other services when those other services are happening) DHCP Wireless + WPA2 security Ability to play multiplayer computer games I am not a networking or computing neophyte, but the last time I messed with network gear was a few years ago, so am needing to dust off knowledge I kinda half have. I have read that I should be wanting to set up the AM200 in half-bridge mode, so that the WRT54GL gets the WAN IP - this sounds like a good idea, but I'd still like to be advised. I have read that the dd-wrt firmware will meet my needs (though I gather I'll need the vpn-specific build, which appears to preclude supporting VOIP), but I'm not wedded to using it. I live in the UK and my ISP supplies me with: a block of 8 static IPs, of which 5 are usable to me a PPPoA ADSL2+ connection

    Read the article

  • LinkSys WRT54GL + AM200 in half-bridge mode - UK setup guide recommendations?

    - by Peter Mounce
    I am basically looking for a good guide on how to set up my home network with this set of hardware. I need: Dynamic DNS Firewall + port-forwarding VPN Wake-on-LAN from outside firewall VOIP would be nice QoS would be nice (make torrents take lower priority to other services when those other services are happening) DHCP Wireless + WPA2 security Ability to play multiplayer computer games I am not a networking or computing neophyte, but the last time I messed with network gear was a few years ago, so am needing to dust off knowledge I kinda half have. I have read that I should be wanting to set up the AM200 in half-bridge mode, so that the WRT54GL gets the WAN IP - this sounds like a good idea, but I'd still like to be advised. I have read that the dd-wrt firmware will meet my needs (though I gather I'll need the vpn-specific build, which appears to preclude supporting VOIP), but I'm not wedded to using it. I live in the UK and my ISP supplies me with: a block of 8 static IPs, of which 5 are usable to me a PPPoA ADSL2+ connection

    Read the article

  • Recommending simple appliance for DansGuardian, iptables, snort inline

    - by SRobertJames
    I'm currently using a Linksys E2000 with dd-wrt. I'd like to add DansGuardian for Content Filtering and snort-inline for IPS; but those require a more powerful box (mainly, more storage). Can you recommend a good device to use? I'm open to both overwrite-the-firmware (like dd-wrt) and designed-to-be-customized boxes. Requirements: 1. 5+ Ethernet ports, pref. GigE 2. small form factor 3. No noise (office environment) 4. low power 5. Not sure about 802.11 wireless Budget < $400, pref. less.

    Read the article

  • Prevent users from Router 2 seeing Router 1 computers

    - by Patrick Robert Shea O'Connor
    I've got 2 Netgear N300 (WNR2000v3) routers. Here's my setup: Modem Router 1 Private Users/Router 2 Public Wireless Users on "Guest" Network. I want to prevent users who are connected to Router 2's "Guest" network from accessing anything that is connected to Router 1. There is an option when setting up the "Guest" network called "Allow guest to access My Local Network" which I thought if unchecked would do this very thing; however, I can still access files and such of computers connected to Router 1. Router 1 assigns 192.0.0.x IP addresses, Router 2 assigns 10.0.0.x IP addresses, how can they even see each other? Do I need to change the subnet or something else?

    Read the article

  • What is the type/classification/term for an PC headset that does not go over the head or back of the

    - by FMFF
    How do I search in the leading auction site for the PC headset(earpiece + microphone) that does not have a band to go around or over your head - instead it is entirely like a cable, with the microphone attached in one of the wires leading from the ear piece? How is it called? I'm not talking about Bluetooth wireless headsets. I have one from Plantronics I got years ago, which they stopped making and I want another one, but don't know how to search. Simply searching for HeadSet or similar terms, brings mostly the newer ones which I don't want. Thank you.

    Read the article

  • Accessing Windows from Linux/Mac by name using TCP/IP

    - by stevekuo
    What are some solutions to access Windows by its computer name from Linux and Mac using TCP/IP. That is, from terminal I want to be able to ping my Windows PCs using its host name. My setup is: Various machines running Ubuntu, Windows XP and OS X. Networked using a consumer grade wireless router which provides DHCP. The only DNS is the ISP's, which resolves Internet names and not local host names. The Windows machines can ping each other by name. The Ubuntu and OS X machines can only ping Windows by IP address (name doesn't work).

    Read the article

  • Server problem (duh)

    - by j-t-s
    Sorry the title couldn't be more specific. I installed Abyss Web Server. I'm running Windows XP Home Edition and I have Wireless Mobile Broadband internet. I used to be able to access (and other people on other networks) my site by entering my ip address in the browser, but after I formatted, and the installed abyss web server again, this does not work anymore. There are no errors. I CAN visit my own site by entering my ip address BUT anybody else can't do the same, it just says "connecting" in the browser's statusbar and it never changes. I have consulted the docs and have found no help. Google hasn't helped with this problem either. Can somebody please help? Thank you :)

    Read the article

  • Server problem (duh)

    - by j-t-s
    Sorry the title couldn't be more specific. I installed Abyss Web Server. I'm running Windows XP Home Edition and I have Wireless Mobile Broadband internet. I used to be able to access (and other people on other networks) my site by entering my ip address in the browser, but after I formatted, and the installed abyss web server again, this does not work anymore. There are no errors. I CAN visit my own site by entering my ip address BUT anybody else can't do the same, it just says "connecting" in the browser's statusbar and it never changes. I have consulted the docs and have found no help. Google hasn't helped with this problem either. Can somebody please help? Thank you :)

    Read the article

  • Not able to access other machines on network

    - by TheVillageIdiot
    Hi I'm running Windows 7 Enterprise (32bit) on my laptop. For some time I'm not able to access other machines using \\192.168.xxx.xxx. I've installed VM Ware player on my machine few days back but I don't remember if it happened just after that or there is some other reason behind it. EDIT:- I've disabled VMWare Bridge Protocol but still no effect. Please help me. PS:- I've used both wireless and wired networks. Network sharing is enabled and I can ping other machines but cannot access network shares. I get following message: \\xxx.xxx.xxx.xxx You might not have permission to use this network resource. Contact the administrator of this server to find out if you have acess permissions. The request is not supported. EDIT (2):- Network Discovery, File and Printer Sharing, Folder sharing are all on.

    Read the article

  • Puttting together binding navigators in a project

    - by vp789
    I am working on a group project in vb.net, in which all my team members are working on individual tables of a database. All of us are using binding navigator,where the GUI is created by drag and drop from the table. Is it possible to attach all these pieces together with imports or references? Will the changes made to the database while working on the program like table adapter can create problem? Do I need to make all those changes in database before importing ? Can you please give suggestions to put the project together.

    Read the article

  • Android EditText within a ListView

    - by metalideath
    I have created a custom Array Adapter to bind a custom row that contains some static text and an editable EditText. I am trying to register to be notified when the user changes the text within the edit text and when notified to determine which ArrayList row the modified EditText corresponds to. In the past with other types of views such as a Spinner I could simply put a reference to the parent view and the row number into the tag for the Spinner view. And then when I was notified that the value changed I read the tag to determine how to correlate it back to the master ArrayList. The problem with registering to be notifed with an EditText change is that you do not get back a view but instead get a TextWatcher and I have no way to correlate back to the parent view or ArrayList row. What is the technique that you need to use in this circumstance?

    Read the article

  • DIR-615 lose internet connection after 3 minutes

    - by Sirber
    I got a new DLink DIR-615 routeur. DSL model connects fine. Connected PCs connects to the internet fine (wireless, wired) fine too. After ~3 minutes, connected PCs cannot go to the internet. Web pages goes timeout, sometimes google talk stays on (working). From the router admin page, pings works correctly (on google.ca), so the connection is active. pc -- routeur -- internet: fail pc -- router: ok router -- internet: ok could it be firewall related? I've read there's a SPI firewall enabled.

    Read the article

  • List view and list adapters for displaying json

    - by Rahul Varma
    Hi, I am trying to display the text from json in a list view. I got help for retrieving the json text from the following... http://www.josecgomez.com/2010/04/30/android-accessing-restfull-web-services-using-json/comment-page-1/#comment-498.... But my problem is that i cant figure out how to display them in list view. I also want to get only some of the text from url(for example, alerttext and date). Can anyone help me in declaring the list adapter and list view in order to display the data in the way i want... Plzzzz...

    Read the article

  • Forward Hostname via my router to another PC for debugging

    - by Markive
    Hi, My web service runs on for example: http://mydomain.com/mywebservice.asmx. This works great, but I have a PDA application which I want to debug it synchronising through this web service. Currently the only way I can do this is to debug the webservice running on the actual server which is far from ideal. What I would like to do is for any device connecting on my wireless network, if it requests mywebservice.asmx for this to forward the request to my development PC and for IIS to then handle the request and allow me to debug in Visual Studio. So device on the network that requests the hostname: mywebservice.asmx will his this PC.. I am at a loss to set this up on my router (Zoom ADSL X6), this is massively out of my scope but any help would be much appreciated

    Read the article

  • DIR-615 lose internet connection after 3 minutes

    - by user31375
    I got a new DLink DIR-615 routeur. DSL model connects fine. Connected PCs connects to the internet fine (wireless, wired) fine too. After ~3 minutes, connected PCs cannot go to the internet. Web pages goes timeout, sometimes google talk stays on (working). From the router admin page, pings works correctly (on google.ca), so the connection is active. pc -- routeur -- internet: fail pc -- router: ok router -- internet: ok could it be firewall related? I've read there's a SPI firewall enabled.

    Read the article

  • Configure Ubuntu9.10 to see hardware of my laptop

    - by michael
    I have installed Ubuntu 9.10 on my laptop. But it can't see all the hardware of the laptop. I would like some help. my laptop has 8G (in Windows7), but Ubuntu only see 2.9G (I get this value from System Monitor under Resource tab my laptop can have 1600x900 resolution (it works in Windows7), but i can only set to 1280x800 in Ubunutu my wireless card does not work. But my wired connection works. Can you please help me in configuring my Ubuntu environment?

    Read the article

< Previous Page | 205 206 207 208 209 210 211 212 213 214 215 216  | Next Page >