Search Results

Search found 15966 results on 639 pages for 'connection'.

Page 21/639 | < Previous Page | 17 18 19 20 21 22 23 24 25 26 27 28  | Next Page >

  • Atheros AR928X wireless connection makes neighbourhood machine drop off line

    - by funicorn
    I have an Acer laptop with Atheros AR928X wireless card installed, supported by ath9k driver in the linux kernel. There are other 5 computers sharing wireless connection via a TPLink 150Mbit/s wireless router. At first I found the network is a little bit slower than it's in Windows7, which I accepted as it should be. However a very strange thing is, each time I connected to the router and downloaded stuff for a while, one of the computers running Windows7 in my local network dropped off from the router. And if I run my laptop under Windows7, everything is fine. What's even stranger is although the network becomes slower, only the certain computer drops and totally freezes in connection with the router. I'm not willing to conclude it's due to the unhealthy connection from my laptop to the router, however we have confirmed this for more than one times and there is no problem with the network when I'm running WIndows7. I'm extremely confused about what's going on. As a Linux user running Ubuntu over 5 years, I am awared that wireless driver in Linux is badly notorious of lack of stability and slow speed. But is it so bad that the unhealthy wireless connection can do damage to another computer in the same local network? I do see a lot of "Tx excessive retries" in iwconfig output. But how exactly does this happen ? Thanks for your help. I guess I have to use this answer box to show the outputs $ sudo iwconfig wlan0 IEEE 802.11bgn ESSID:"TP-LINK111" Mode:Managed Frequency:2.427 GHz Access Point: E0:05:C5:E8:A9:92 Bit Rate=121.5 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=47/70 Signal level=-63 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:2 Invalid misc:23 Missed beacon:0 To show what's wrong with the wireless connection, I ran iwconfig again within 3 minutes, during which time I hardly did anything and the network was not much busy than being nearly idle $ sudo iwconfig wlan0 IEEE 802.11bgn ESSID:"TP-LINK111" Mode:Managed Frequency:2.427 GHz Access Point: E0:05:C5:E8:A9:92 Bit Rate=121.5 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=48/70 Signal level=-62 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:9 Invalid misc:28 Missed beacon:0 You can see Tx excessive retires and Invalid misc increase very quickly. $ sudo iwlist wlan0 modu wlan0 unknown modulation information. $ sudo iwlist wlan0 channel wlan0 13 channels in total; available frequencies : Channel 01 : 2.412 GHz Channel 02 : 2.417 GHz Channel 03 : 2.422 GHz Channel 04 : 2.427 GHz Channel 05 : 2.432 GHz Channel 06 : 2.437 GHz Channel 07 : 2.442 GHz Channel 08 : 2.447 GHz Channel 09 : 2.452 GHz Channel 10 : 2.457 GHz Channel 11 : 2.462 GHz Channel 12 : 2.467 GHz Channel 13 : 2.472 GHz Current Frequency:2.427 GHz (Channel 4)

    Read the article

  • XMLHttpRequest not working, trying to test database connection [closed]

    - by Frederick Marcoux
    I'm currently creating my own CMS for personnal use but I'm blocked at a code. I'm trying to make a installation script but the AJAX request to test if database works, doesn't work... There's my JS code: function testDB() { "use strict"; var host = document.getElementById('host').value; var username = document.getElementById('username').value; var password = document.getElementById('password').value; var db = document.getElementById('db_name').value; var xmlhttp = new XMLHttpRequest(); var url = "test_db.php"; var params = "host="+host+"&username="+username+"&password="+password+"&db="+db; xmlhttp.open("POST", url, true); xmlhttp.setRequestHeader("Content-type", "application/x-www-form-urlencoded"); xmlhttp.setRequestHeader("Content-length", params.length); xmlhttp.setRequestHeader("Connection", "close"); xmlhttp.send(params); $('#loader').removeAttr('style'); if (xmlhttp.responseText !== '') { if (xmlhttp.readyState===4 && xmlhttp.status===200) { $('#next').removeAttr('disabled'); $('#test').attr('disabled', 'disabled'); $('#test').text('Connection Successful!'); $('#test').addClass('btn-success'); $('#login').addClass('success'); $('#login1').addClass('success'); $('#db').addClass('success'); $('#loader').attr('style', 'display: none;'); } else { $('#next').attr('disabled', 'disabled'); $('#test').removeClass('btn-success'); $('#test').removeAttr('disabled'); $('#test').text('Test Connection'); $('#login').removeClass('success'); $('#login1').removeClass('success'); $('#db').removeClass('success'); $('#loader').attr('style', 'display: none;'); } } else { $('#next').attr('disabled', 'disabled'); $('#next').attr('disabled', 'disabled'); $('#test').removeClass('btn-success'); $('#test').removeAttr('disabled'); $('#test').text('Test Connection'); $('#login').removeClass('success'); $('#login1').removeClass('success'); $('#db').removeClass('success'); $('#loader').attr('style', 'display: none;'); } } And there's my PHP code: <?php $link = mysql_connect($_POST['host'], $_POST['username'], $_POST['password']); if (!$link) { echo ''; } else { if (mysql_select_db($_POST['db'])) { echo 'Connection Successful!'; } else { echo ''; } } mysql_close($link); ?> I don't know why it doesn't work but I tried with JQuery $.ajax, $.get, $.post but nothing work...

    Read the article

  • Connection error in java website. Tnsping shows that the service is running

    - by user1439090
    I have a java website application running in windows 7 which uses oracle database for its functionalities. The database has default SID name orcl. When I use tnsping, I can see that the orcl service is active. Also most of the application is working fine except for one part. I was wondering if someone could help me with the following error:- 1. cause: message:null,java.lang.reflect.InvocationTargetException at sun.reflect.NativeConstructorAccessorImpl.newInstance0(Native Method) at sun.reflect.NativeConstructorAccessorImpl.newInstance(NativeConstructorAccessorImpl.java:39) at sun.reflect.DelegatingConstructorAccessorImpl.newInstance(DelegatingConstructorAccessorImpl.java:27) at java.lang.reflect.Constructor.newInstance(Constructor.java:513) at org.olat.course.statistic.StatisticAutoCreator.createController(StatisticAutoCreator.java:73) at org.olat.course.statistic.StatisticActionExtension.createController(StatisticActionExtension.java:40) at org.olat.course.statistic.StatisticMainController.createController(StatisticMainController.java:80) at org.olat.core.gui.control.generic.layout.GenericMainController.getContentCtr(GenericMainController.java:258) at org.olat.core.gui.control.generic.layout.GenericMainController.event(GenericMainController.java:221) at org.olat.core.gui.control.DefaultController.dispatchEvent(DefaultController.java:196) 2. cause: message:Could not get JDBC Connection; nested exception is java.sql.SQLException: The Network Adapter could not establish the connection,org.springframework.jdbc.CannotGetJdbcConnectionException at org.springframework.jdbc.datasource.DataSourceUtils.getConnection(DataSourceUtils.java:80) at org.springframework.jdbc.core.JdbcTemplate.execute(JdbcTemplate.java:381) at org.springframework.jdbc.core.JdbcTemplate.query(JdbcTemplate.java:455) at org.springframework.jdbc.core.JdbcTemplate.query(JdbcTemplate.java:463) at org.springframework.jdbc.core.JdbcTemplate.queryForObject(JdbcTemplate.java:471) at org.springframework.jdbc.core.JdbcTemplate.queryForObject(JdbcTemplate.java:476) at org.springframework.jdbc.core.JdbcTemplate.queryForLong(JdbcTemplate.java:480) at org.olat.course.statistic.SimpleStatisticInfoHelper.doGetFirstLoggingTableCreationDate(SimpleStatisticInfoHelper.java:63) at org.olat.course.statistic.SimpleStatisticInfoHelper.getFirstLoggingTableCreationDate(SimpleStatisticInfoHelper.java:81) at org.olat.course.statistic.StatisticDisplayController.getStatsSinceStr(StatisticDisplayController.java:517) 3. cause: message:The Network Adapter could not establish the connection,java.sql.SQLException at oracle.jdbc.driver.SQLStateMapping.newSQLException(SQLStateMapping.java:70) at oracle.jdbc.driver.DatabaseError.newSQLException(DatabaseError.java:133) at oracle.jdbc.driver.DatabaseError.throwSqlException(DatabaseError.java:199) at oracle.jdbc.driver.DatabaseError.throwSqlException(DatabaseError.java:480) at oracle.jdbc.driver.T4CConnection.logon(T4CConnection.java:413) at oracle.jdbc.driver.PhysicalConnection.(PhysicalConnection.java:508) at oracle.jdbc.driver.T4CConnection.(T4CConnection.java:203) at oracle.jdbc.driver.T4CDriverExtension.getConnection(T4CDriverExtension.java:33) at oracle.jdbc.driver.OracleDriver.connect(OracleDriver.java:510) at java.sql.DriverManager.getConnection(DriverManager.java:582) 4. cause: message:The Network Adapter could not establish the connection,oracle.net.ns.NetException at oracle.net.nt.ConnStrategy.execute(ConnStrategy.java:328) at oracle.net.resolver.AddrResolution.resolveAndExecute(AddrResolution.java:421) at oracle.net.ns.NSProtocol.establishConnection(NSProtocol.java:634) at oracle.net.ns.NSProtocol.connect(NSProtocol.java:208) at oracle.jdbc.driver.T4CConnection.connect(T4CConnection.java:966) at oracle.jdbc.driver.T4CConnection.logon(T4CConnection.java:292) at oracle.jdbc.driver.PhysicalConnection.(PhysicalConnection.java:508) at oracle.jdbc.driver.T4CConnection.(T4CConnection.java:203) at oracle.jdbc.driver.T4CDriverExtension.getConnection(T4CDriverExtension.java:33) at oracle.jdbc.driver.OracleDriver.connect(OracleDriver.java:510) 5. cause: message:Connection timed out: connect,java.net.ConnectException at java.net.PlainSocketImpl.socketConnect(Native Method) at java.net.PlainSocketImpl.doConnect(PlainSocketImpl.java:333) at java.net.PlainSocketImpl.connectToAddress(PlainSocketImpl.java:195) at java.net.PlainSocketImpl.connect(PlainSocketImpl.java:182) at java.net.SocksSocketImpl.connect(SocksSocketImpl.java:366) at java.net.Socket.connect(Socket.java:525) at java.net.Socket.connect(Socket.java:475) at java.net.Socket.(Socket.java:372) at java.net.Socket.(Socket.java:186) at oracle.net.nt.TcpNTAdapter.connect(TcpNTAdapter.java:127)

    Read the article

  • How to configure VPN in Windows XP

    - by SAMIR BHOGAYTA
    VPN Overview A VPN is a private network created over a public one. It’s done with encryption, this way, your data is encapsulated and secure in transit – this creates the ‘virtual’ tunnel. A VPN is a method of connecting to a private network by a public network like the Internet. An internet connection in a company is common. An Internet connection in a Home is common too. With both of these, you could create an encrypted tunnel between them and pass traffic, safely - securely. If you want to create a VPN connection you will have to use encryption to make sure that others cannot intercept the data in transit while traversing the Internet. Windows XP provides a certain level of security by using Point-to-Point Tunneling Protocol (PPTP) or Layer Two Tunneling Protocol (L2TP). They are both considered tunneling protocols – simply because they create that virtual tunnel just discussed, by applying encryption. Configure a VPN with XP If you want to configure a VPN connection from a Windows XP client computer you only need what comes with the Operating System itself, it's all built right in. To set up a connection to a VPN, do the following: 1. On the computer that is running Windows XP, confirm that the connection to the Internet is correctly configured. • You can try to browse the internet • Ping a known host on the Internet, like yahoo.com, something that isn’t blocking ICMP 2. Click Start, and then click Control Panel. 3. In Control Panel, double click Network Connections 4. Click Create a new connection in the Network Tasks task pad 5. In the Network Connection Wizard, click Next. 6. Click Connect to the network at my workplace, and then click Next. 7. Click Virtual Private Network connection, and then click Next. 8. If you are prompted, you need to select whether you will use a dialup connection or if you have a dedicated connection to the Internet either via Cable, DSL, T1, Satellite, etc. Click Next. 9. Type a host name, IP or any other description you would like to appear in the Network Connections area. You can change this later if you want. Click Next. 10. Type the host name or the Internet Protocol (IP) address of the computer that you want to connect to, and then click Next. 11. You may be asked if you want to use a Smart Card or not. 12. You are just about done, the rest of the screens just verify your connection, click Next. 13. Click to select the Add a shortcut to this connection to my desktop check box if you want one, if not, then leave it unchecked and click finish. 14. You are now done making your connection, but by default, it may try to connect. You can either try the connection now if you know its valid, if not, then just close it down for now. 15. In the Network Connections window, right-click the new connection and select properties. Let’s take a look at how you can customize this connection before it’s used. 16. The first tab you will see if the General Tab. This only covers the name of the connection, which you can also rename from the Network Connection dialog box by right clicking the connection and selecting to rename it. You can also configure a First connect, which means that Windows can connect the public network (like the Internet) before starting to attempt the ‘VPN’ connection. This is a perfect example as to when you would have configured the dialup connection; this would have been the first thing that you would have to do. It's simple, you have to be connected to the Internet first before you can encrypt and send data over it. This setting makes sure that this is a reality for you. 17. The next tab is the Options Tab. It is The Options tab has a lot you can configure in it. For one, you have the option to connect to a Windows Domain, if you select this check box (unchecked by default), then your VPN client will request Windows logon domain information while starting to work up the VPN connection. Also, you have options here for redialing. Redial attempts are configured here if you are using a dial up connection to get to the Internet. It is very handy to redial if the line is dropped as dropped lines are very common. 18. The next tab is the Security Tab. This is where you would configure basic security for the VPN client. This is where you would set any advanced IPSec configurations other security protocols as well as requiring encryption and credentials. 19. The next tab is the Networking Tab. This is where you can select what networking items are used by this VPN connection. 20. The Last tab is the Advanced Tab. This is where you can configure options for configuring a firewall, and/or sharing. Connecting to Corporate Now that you have your XP VPN client all set up and ready, the next step is to attempt a connection to the Remote Access or VPN server set up at the corporate office. To use the connection follow these simple steps. To open the client again, go back to the Network Connections dialog box. 1. One you are in the Network Connection dialog box, double-click, or right click and select ‘Connect’ from the menu – this will initiate the connection to the corporate office. 2. Type your user name and password, and then click Connect. Properties bring you back to what we just discussed in this article, all the global settings for the VPN client you are using. 3. To disconnect from a VPN connection, right-click the icon for the connection, and then click “Disconnect” Summary In this article we covered the basics of building a VPN connection using Windows XP. This is very handy when you have a VPN device but don’t have the ‘client’ that may come with it. If the VPN Server doesn’t use highly proprietary protocols, then you can use the XP client to connect with. In a future article I will get into the nuts and bolts of both IPSec and more detail on how to configure the advanced options in the Security tab of this client. 678: The remote computer did not respond. 930: The authentication server did not respond to authentication requests in a timely fashion. 800: Unable to establish the VPN connection. 623: The system could not find the phone book entry for this connection. 720: A connection to the remote computer could not be established. More on : http://www.windowsecurity.com/articles/Configure-VPN-Connection-Windows-XP.html

    Read the article

  • Messenger Thinks My Ip is Invalid

    - by Umut Benzer
    Hello. I am using Windows Live Messenger 2009 on Windows 7. I am using a 3G modem (ZTE Propietary USB Modem) I connect to the Internet using a software my ISP provided me. In last three days, my Messenger started to disconnect. Here is what I observed and tried to do: 1- I can browse web, can do FTP transfer etc. and obiviously have a valid IP. 2- I can sign in to Messenger (appear offline) but when I change my status to anything other then appear offline, Messenger says my connection to service has been lost. (However, it exists.) 3- When I run, MSN Connection Troubleshooter, it says my IP is invalid. When I click repair, it says repaired and just after that, I run the troubleshooter again, and it says my IP is invalid again. (However, it is valid and I am browsing the net.) 4- If I connect the Internet through eterhet or wireless there is no problem at all. 5- I re-installed Messenger (deleting all settings manually through registry and folders), re-installed all drivers and software related to USB 3G Modem. It doesn't work. And then, I took a full backup then formatted entire computer, installed a fresh windows 7, after 5 minutes, the same problem occured. What do you recommend? What can I do? Addition As seen on screenshot, it says Server IPv4 adress is 0.0.0.0 It seems like a problem, I don't know if it is. If it is, how can I solve it? Here is what I get, when I netstat. PPP adapter TTNET internet: Connection-specific DNS Suffix . : IPv4 Address. . . . . . . . . . . : 217.174.39.122 Subnet Mask . . . . . . . . . . . : 255.255.255.255 Default Gateway . . . . . . . . . : 0.0.0.0 Wireless LAN adapter Wireless Network Connection 2: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Wireless LAN adapter Wireless Network Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : ege.edu.tr Ethernet adapter Local Area Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 16: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 13: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter 6TO4 Adapter: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 9: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 11: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 12: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 14: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 17: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 25: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 20: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 18: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 19: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 22: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 21: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 15: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 23: Connection-specific DNS Suffix . : IPv6 Address. . . . . . . . . . . : 2001:0:4137:9e74:2448:3909:2a2c:eb7b Link-local IPv6 Address . . . . . : fe80::2448:3909:2a2c:eb7b%30 Default Gateway . . . . . . . . . : Tunnel adapter Local Area Connection* 24: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter isatap.{CFFCFEDB-6B53-42E0-B091-548B9ADE9C9D}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 26: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 27: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 29: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 31: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 28: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 32: Connection-specific DNS Suffix . : IPv6 Address. . . . . . . . . . . : 2002:d9ae:277a::d9ae:277a Default Gateway . . . . . . . . . : 2002:c058:6301::c058:6301 Tunnel adapter Local Area Connection* 30: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter isatap.{157CF713-B3AC-4701-87A9-14C23CA60AAB}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter isatap.ege.edu.tr: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter isatap.{0D3CD01B-0993-4B37-89B8-12557ECF484D}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . :

    Read the article

  • recent unreliable wireless connection on 10.04 and 10.10

    - by gabkdlly
    Recently, my internet connection over wireless has become unreliable, on both a Dell laptop running Ubuntu 10.04 as well as my Desktop running Ubuntu 10.10 . The problem does not seem to occur on a laptop running Windows Vista. The problem does not seem to occur on my Openmoko Freerunner ( running Android 1.5 ), though I hardly ever use this device to connect over WLAN, so the problem may have just slipped by. This problem does not seem to appear when I boot into Ubuntu 9.10 from a live CD ( more precisely, I was able to ping fu-berlin.de for an hour without any packet loss ). Under Ubuntu 10.10, I am experiencing about 33% packet loss. On my main Ubuntu Desktop, I have tried the following wireless devices: a Longshine PCI card ( an old device with an RTL8180L chip ) a D-Link DWL-510 PCI card ( this device threw warnings in dmesg ) a USB device from MSI ( US54EX ). Usually my wireless network shows up in the network manager with a normal signal strength, even when the connection speed is slow ( which happens often ) or the connection gets reset ( asking me to click connect to re-authenticate my wireless connection ). I have observed this problem with a Netgear KWGR614 Router ( with the manufacturers firmware ), as well as with a TP-LINK TL-WR741ND router running OpenWrt. Taking a look at my routers logs, I find many instances of the following line: Tuesday,04 Jan 2011 03:53:01 [TCP SYN Flood][Deny access policy matched, dropping packet] I know that the Netgear router is susceptible to denial of service attacks, as I have previously been able to disrupt its operation by putting an nmap scan into a while loop. I use WEP on the Netgear router and WPA on the TP-LINK to encrypt the wireless connections. Is it possible that someone is jamming my signal ?

    Read the article

  • recent unreliable wireless connection with Netgear KWGR614 router

    - by gabkdlly
    Recently, my internet connection over wireless ( via a Netgear KWGR614 router ) has become unreliable, on both a Dell laptop running Ubuntu 10.04 as well as my Desktop running Ubuntu 10.10 . The problem does not seem to occur on a laptop running Windows Vista, nor on a Desktop running Windows 7 ( this machine is connected with an ethernet cable ). The problem does not seem to occur on my Openmoko Freerunner ( running Android 1.5 ), though I hardly ever use this device to connect over WLAN, so the problem may have just slipped by. On my main Ubuntu Desktop, I have tried the following wireless devices: a Longshine PCI card ( an old device with an RTL8180L chip ) a D-Link DWL-510 PCI card ( this device threw warnings in dmesg ) a USB device from MSI ( US54EX ). Usually my wireless network shows up in the network manager with a normal signal strength, even when the connection speed is slow or the connection gets reset ( asking me to click connect to re-authenticate my wireless connection ). I know that this router is susceptible to denial of service attacks, as I have previously been able to disrupt its operation by putting an nmap scan into a while loop. Is it possible that someone is jamming my signal ?

    Read the article

  • recent unreliable wireless connection

    - by gabkdlly
    Recently, my internet connection over wireless ( via a Netgear KWGR614 router ) has become unreliable, on both a Dell laptop running Ubuntu 10.04 as well as my Desktop running Ubuntu 10.10 . The problem does not seem to occur on a laptop running Windows Vista, nor on a Desktop running Windows 7 ( this machine is connected with an ethernet cable ). The problem does not seem to occur on my Openmoko Freerunner ( running Android 1.5 ), though I hardly ever use this device to connect over WLAN, so the problem may have just slipped by. On my main Ubuntu Desktop, I have tried the following wireless devices: a Longshine PCI card ( an old device with an RTL8180L chip ) a D-Link DWL-510 PCI card ( this device threw warnings in dmesg ) a USB device from MSI ( US54EX ). Usually my wireless network shows up in the network manager with a normal signal strength, even when the connection speed is slow or the connection gets reset ( asking me to click connect to re-authenticate my wireless connection ). I have observed this problem with a Netgear KWGR614 Router ( with the manufacturers firmware ), as well as with a TP-LINK TL-WR741ND router running OpenWrt. Taking a look at my routers logs, I find many instances of the following line: Tuesday,04 Jan 2011 03:53:01 [TCP SYN Flood][Deny access policy matched, dropping packet] I know that the Netgear router is susceptible to denial of service attacks, as I have previously been able to disrupt its operation by putting an nmap scan into a while loop. I use WEP or WPA to encrypt the wireless network. Is it possible that someone is jamming my signal ?

    Read the article

  • Pros/cons of reading connection string from physical file vs Application object (ASP.NET)?

    - by HaterTot
    my ASP.NET application reads an xml file to determine which environment it's currently in (e.g. local, development, production). It checks this file every single time it opens a connection to the database, in order to know which connection string to grab from the Application Settings. I'm entering a phase of development where efficiency is becoming a concern. I don't think it's a good idea to have to read a file on a physical disk ever single time I wish to access the database (very often). I was considering storing the connection string in Application["ConnectionString"]. So the code would be public static string GetConnectionString { if (Application["ConnectionString"] == null) { XmlDocument doc = new XmlDocument(); doc.Load(HttpContext.Current.Request.PhysicalApplicationPath + "bin/ServerEnvironment.xml"); XmlElement xe = (XmlElement) xnl[0]; switch (xe.InnerText.ToString().ToLower()) { case "local": connString = Settings.Default.ConnectionStringLocal; break; case "development": connString = Settings.Default.ConnectionStringDevelopment; break; case "production": connString = Settings.Default.ConnectionStringProduction; break; default: throw new Exception("no connection string defined"); } Application["ConnectionString"] = connString; } return Application["ConnectionString"].ToString(); } I didn't design the application so I figure there must have been a reason for reading the xml file every time (to change settings while the application runs?) I have very little concept of the inner workings here. What are the pros and cons? Do you think I'd see a small performance gain by implementing the function above? THANKS

    Read the article

  • MySql ODBC connection in VB6 on WinXP VERY slow. Other machines on same network are fast.

    - by Matthew
    Hi All, I have a VB6 application that has been performing very well. Recently, we upgraded our server to a Windows 2003 server. Migration of the databases and shares went well and we experienced no problems. Except one. And it has happened at multiple sites. I use the MySQL ODBC 5.1 connector to point to my MySQL database. On identical machines (as far as I can tell, they are client machines not ours), access to the DB is lightning fast on all but one computer. They use the same software and have the same connection strings. And I'm sure it's not the program, but the ODBC connection. When I press the 'Test Connection' button in the ODBC connection string window, it can take up to 10 seconds on the poorly performing machine to respond with a success. All the other computers are instantaneous. I have tried using ip address versus the machine name in the UDL, no change. I enabled option 256, which sped it up initially, but it's slow again. Most of the time on a restart the program will be fast for an hour or so then go slow again with the option 256 enabled. Frankly, I am out of ideas and willing to entertain any and all ideas or suggestions. This is getting pretty frustrating. Anyone ever experience anything like this?

    Read the article

  • PPTP connection disconnect

    - by Vladimir Franciz S. Blando
    My pptp connection wont stay connected, it will disconnect in less than a minute here are some relevant log entries May 31 13:32:31 localhost NetworkManager[931]: <info> Starting VPN service 'pptp'... May 31 13:32:31 localhost NetworkManager[931]: <info> VPN service 'pptp' started (org.freedesktop.NetworkManager.pptp), PID 15216 May 31 13:32:31 localhost NetworkManager[931]: <info> VPN service 'pptp' appeared; activating connections May 31 13:32:31 localhost NetworkManager[931]: <info> VPN plugin state changed: init (1) May 31 13:32:31 localhost NetworkManager[931]: <info> VPN plugin state changed: starting (3) May 31 13:32:31 localhost NetworkManager[931]: <info> VPN connection 'Dynalabs' (Connect) reply received. May 31 13:32:31 localhost pppd[15221]: Plugin /usr/lib/pppd/2.4.5/nm-pptp-pppd-plugin.so loaded. May 31 13:32:31 localhost pppd[15221]: pppd 2.4.5 started by root, uid 0 May 31 13:32:31 localhost pptp[15224]: nm-pptp-service-15216 log[main:pptp.c:314]: The synchronous pptp option is NOT activated May 31 13:32:31 localhost pppd[15221]: Using interface ppp0 May 31 13:32:31 localhost pppd[15221]: Connect: ppp0 <--> /dev/pts/5 May 31 13:32:31 localhost NetworkManager[931]: SCPlugin-Ifupdown: devices added (path: /sys/devices/virtual/net/ppp0, iface: ppp0) May 31 13:32:31 localhost NetworkManager[931]: SCPlugin-Ifupdown: device added (path: /sys/devices/virtual/net/ppp0, iface: ppp0): no ifupdown configuration found. May 31 13:32:32 localhost pptp[15235]: nm-pptp-service-15216 log[ctrlp_rep:pptp_ctrl.c:251]: Sent control packet type is 1 'Start-Control-Connection-Request' May 31 13:32:32 localhost pptp[15235]: nm-pptp-service-15216 log[ctrlp_disp:pptp_ctrl.c:739]: Received Start Control Connection Reply May 31 13:32:32 localhost pptp[15235]: nm-pptp-service-15216 log[ctrlp_disp:pptp_ctrl.c:773]: Client connection established. May 31 13:32:33 localhost pptp[15235]: nm-pptp-service-15216 log[ctrlp_rep:pptp_ctrl.c:251]: Sent control packet type is 7 'Outgoing-Call-Request' May 31 13:32:34 localhost pptp[15235]: nm-pptp-service-15216 log[ctrlp_disp:pptp_ctrl.c:858]: Received Outgoing Call Reply. May 31 13:32:34 localhost pptp[15235]: nm-pptp-service-15216 log[ctrlp_disp:pptp_ctrl.c:897]: Outgoing call established (call ID 0, peer's call ID 1536). May 31 13:32:37 localhost pppd[15221]: CHAP authentication succeeded May 31 13:32:37 localhost kernel: [54007.078553] PPP MPPE Compression module registered May 31 13:32:40 localhost pppd[15221]: MPPE 128-bit stateless compression enabled May 31 13:32:42 localhost pppd[15221]: local IP address 10.100.0.52 May 31 13:32:42 localhost pppd[15221]: remote IP address 10.100.0.1 May 31 13:32:42 localhost pppd[15221]: primary DNS address 4.2.2.1 May 31 13:32:42 localhost pppd[15221]: secondary DNS address 255.255.255.255 May 31 13:32:42 localhost NetworkManager[931]: <info> VPN connection 'Dynalabs' (IP Config Get) reply received. May 31 13:32:42 localhost NetworkManager[931]: <info> VPN Gateway: 103.28.219.2 May 31 13:32:42 localhost NetworkManager[931]: <info> Tunnel Device: ppp0 May 31 13:32:42 localhost NetworkManager[931]: <info> Internal IP4 Address: 10.100.0.52 May 31 13:32:42 localhost NetworkManager[931]: <info> Internal IP4 Prefix: 32 May 31 13:32:42 localhost NetworkManager[931]: <info> Internal IP4 Point-to-Point Address: 10.100.0.1 May 31 13:32:42 localhost NetworkManager[931]: <info> Maximum Segment Size (MSS): 0 May 31 13:32:42 localhost NetworkManager[931]: <info> Forbid Default Route: no May 31 13:32:42 localhost NetworkManager[931]: <info> Internal IP4 DNS: 4.2.2.1 May 31 13:32:42 localhost NetworkManager[931]: <info> Internal IP4 DNS: 255.255.255.255 May 31 13:32:42 localhost NetworkManager[931]: <info> DNS Domain: '(none)' May 31 13:32:43 localhost dnsmasq[2127]: exiting on receipt of SIGTERM May 31 13:32:43 localhost NetworkManager[931]: <info> DNS: starting dnsmasq... May 31 13:32:43 localhost NetworkManager[931]: <info> (ppp0): writing resolv.conf to /sbin/resolvconf May 31 13:32:43 localhost dnsmasq[15290]: error at line 2 of /var/run/nm-dns-dnsmasq.conf May 31 13:32:43 localhost dnsmasq[15290]: FAILED to start up May 31 13:32:43 localhost NetworkManager[931]: <info> VPN connection 'Dynalabs' (IP Config Get) complete. May 31 13:32:43 localhost NetworkManager[931]: <info> Policy set 'Dynalabs' (ppp0) as default for IPv4 routing and DNS. May 31 13:32:43 localhost NetworkManager[931]: <info> VPN plugin state changed: started (4) May 31 13:32:43 localhost NetworkManager[931]: <warn> dnsmasq exited with error: Configuration problem (1) May 31 13:32:43 localhost NetworkManager[931]: <info> (ppp0): writing resolv.conf to /sbin/resolvconf May 31 13:32:43 localhost dbus[872]: [system] Activating service name='org.freedesktop.nm_dispatcher' (using servicehelper) May 31 13:32:43 localhost dbus[872]: [system] Successfully activated service 'org.freedesktop.nm_dispatcher' May 31 13:33:00 localhost ntpdate[15370]: step time server 91.189.94.4 offset -1.110301 sec May 31 13:33:21 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0xd6d6 May 31 13:33:21 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x93aa May 31 13:33:21 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0xcc83 May 31 13:33:21 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x2031 May 31 13:33:21 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x13d4 May 31 13:33:22 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x5b11 May 31 13:33:22 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x414b May 31 13:33:22 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x2f5f May 31 13:33:22 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0xe9ff May 31 13:33:23 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x8e20 May 31 13:33:23 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x8f0 May 31 13:33:23 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0xf166 May 31 13:33:23 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x36e6 May 31 13:33:23 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0xdd19 May 31 13:33:23 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0xda26 May 31 13:33:24 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0xac5 May 31 13:33:24 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x53a5 May 31 13:33:24 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x507e May 31 13:33:24 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x1dc5 May 31 13:33:24 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0xf87b May 31 13:33:24 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x2f27 May 31 13:33:24 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0xd10c May 31 13:33:24 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x66ef May 31 13:33:24 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0xa294 May 31 13:33:24 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0xb15 May 31 13:33:24 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x52a2 May 31 13:33:24 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0xd863 May 31 13:33:24 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x8a96 May 31 13:33:24 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0xde19 May 31 13:33:24 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x9763 May 31 13:33:24 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0xb23 May 31 13:33:24 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x83ca May 31 13:33:24 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x964e May 31 13:33:24 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0xe8ae May 31 13:33:24 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0xf614 May 31 13:33:25 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x9b1 May 31 13:33:25 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0xf086 May 31 13:33:25 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0xbff4 May 31 13:33:25 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x66c5 May 31 13:33:25 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0xe42 May 31 13:33:25 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0xf295 May 31 13:33:25 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x86fe May 31 13:33:26 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x3bc1 May 31 13:33:26 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0xbaad May 31 13:33:26 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x88b5 May 31 13:33:26 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0xd7a May 31 13:33:26 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x30d5 May 31 13:33:26 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x2d8f May 31 13:33:26 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x3933 May 31 13:33:26 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x8d42 May 31 13:33:26 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x4b4 May 31 13:33:26 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0xa205 May 31 13:33:26 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x7cc5 May 31 13:33:26 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x1b6a May 31 13:33:26 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0xf004 May 31 13:33:26 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x21b6 May 31 13:33:26 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x51eb

    Read the article

  • How to See What Web Sites Your Computer is Secretly Connecting To

    - by Lori Kaufman
    Has your internet connection become slower than it should be? There may be a chance that you have some malware, spyware, or adware that is using your internet connection in the background without your knowledge. Here’s how to see what’s going on under the hood. Secret Squirrel by akumath HTG Explains: When Do You Need to Update Your Drivers? How to Make the Kindle Fire Silk Browser *Actually* Fast! Amazon’s New Kindle Fire Tablet: the How-To Geek Review

    Read the article

  • Networking disabled

    - by Terry Dixon
    Both the Wifi and the ethernet connection to the internet are not working. All had been functioning fine until the Ubuntu suspended itself. On re-starting, the connection to internet failed to function and now I get the message "Network Disabled" whenever I re-boot. nm-tool tells me the state is "asleep". Stopping and starting the NetworkManager has no effect The machine is an Inspiron 9300 and work perfectly with Windows. How do I wake the networking up? Thanks

    Read the article

  • Dell Inspiron 1501 no wired/wireless w/12.04 or13.04

    - by Niven
    I don't know what to do. Every install of either 13.04 and 12.04 on my Dell does not have a working wired or wireless internet connection. However, if I am running from USB in the trial mode I have working internet through a wired connection using the same ethernet cord. I honestly at this point do not know what I can do to fix this issue as I have gone through every possible fix I have found here and in other places.

    Read the article

  • How to share computer's internet connection among network users

    - by RBA
    I wanted to connect to internet from my mobile through laptop wireless-broadband internet connection.. For that I have gone to Network Places, there i have done appropriate settings for "Wireless Network Connection" and "Bluetooth Personal Area Network Connection",, but that Bluetooth connection is still not showing connected.. I have checked the option for "Allow other network users to connect through this computers Internet connection", but still my Bluetooth Connection is still showing not connected.. Please help me out,, as to how can i achieve the same,, as i am having Broadband internet connection, which comes wirelessly to my laptop through a router/modem..

    Read the article

  • How do I effectively store a connection string in machine.config only?

    - by Scott Bedwell
    We are moving to an environment with multiple engines of MS SQL running on the same server (a test engine and a production engine). We also have separate test and production web servers, and would like for our asp.net applications to "magically" use the test database engine on the test web server and the production database engine on the production web servers. We would like to store the connection strings in machine.config rather than in web.config, but when we put it in machine.config, visual studio's IDE (particularly with datasets) does not recognize that the machine.config contains the connection. Does anyone know of a solution for displaying these machine.config connection strings in visual studio, or of a different solution that would accommodate for this? Thanks.

    Read the article

  • How do I deal with connection strings in a Click-Once application?

    - by Pwninstein
    I'm thinking of building a Click-Once application, and am trying to wrap my head around how to handle the whole connection string issue. The problem is the following: I want to use EF to get data directly from each client, thus requiring each client to have a connection string configured (this is not the issue). How do I deal with clients that are not on the same domain as the SQL Server being queried? In other words, if I tried to run my app from home as opposed to from work, what should my connection string look like? Would I need to configure my SQL Server differently to allow this scenario? Thanks in advance!

    Read the article

  • How to Connect Your Android to Your PC’s Internet Connection Over USB

    - by Chris Hoffman
    People often “tether” their computers to their smartphones, sending their computer’s network traffic over the device’s cellular data connection. “Reverse tethering” is the opposite – tethering your Android smartphone or tablet to your PC to use your PC’s Internet connection. This method requires a rooted Android and a Windows PC, but it’s very easy to use. If your computer has Wi-Fi, it may be easier to create a Wi-Fi hotspot using a utility like Connectify instead. How to Make Your Laptop Choose a Wired Connection Instead of Wireless HTG Explains: What Is Two-Factor Authentication and Should I Be Using It? HTG Explains: What Is Windows RT and What Does It Mean To Me?

    Read the article

  • setup WAN miniport(PPPOE) internet connection

    - by Ankit Shah
    Hello I'm from Ahmedabad, India. I want to setup my GTPL(i.e. the service provider) PPPOE internet connection in ubuntu 12.04 . please help..... I had tried to configure my internet connection in fedora 16 using the following method which worked fine :-- I've tried to go to Edit Connection then to the DSL tab then ADDenter my username and passwordSave. But this method didn't help in ubuntu 12.04. please help me out immediately....... Thank you in advance.

    Read the article

  • Broadband internet connection problem on Ubuntu 11.10

    - by zahidul hossain
    I am using a broadband internet connection from a local ISP. I installed Ubuntu 11.10 yesterday but I could not configure my internet connection like I did on 10.04 before. On 10.04, it was easy to configure and connect to internet. Generally, I used DSL settings to configure my net. There I enter my user name, my connection's name and password to connect with net. But now in 11.10 it's not working. What can I do to connect it perfectly?

    Read the article

  • How to share internet connection and making the client accessible over the lan

    - by Dario Silva Moran
    I've a Pc with Ubuntu 14.04 connected to a linkys router through wlan0, and I'd like to share internet connection to an AVR with ethernet port. This is pretty simple if only internet connection is required for the AVR: actually, creating an ethernet connection as "Shared with other computers" and setting up the AVR IP configuration to use DHCP works just fine, but that makes a private class A lan between those two; of course ip addresses are not in the range of the LAN the router is managing. So, I tried with static ip on both sides (Ubuntu eth0 and AVR ip). Tried many combinations, none of them work to provide Internet access to the AVR and at the same time make the AVR accessible over the network through his static ip address (say, 192.168.0.110). Any tips around to share??

    Read the article

  • PPTP VPN connection with dd-wrt terminates

    - by StalkerNOVA
    I have problems with connection to DD-WRT router with PPTP server installed. Win7 has no problems with connection to it. But in Ubuntu I'm getting all the time: Dec 28 21:52:14 IT-nb pppd[4209]: Plugin /usr/lib/pppd/2.4.5//nm-pptp-pppd-plugin.so loaded. Dec 28 21:52:14 IT-nb pppd[4209]: pppd 2.4.5 started by root, uid 0 Dec 28 21:52:14 IT-nb pppd[4209]: Using interface ppp0 Dec 28 21:52:14 IT-nb pppd[4209]: Connect: ppp0 <--> /dev/pts/2 Dec 28 21:52:18 IT-nb pppd[4209]: Connection terminated. Dec 28 21:52:18 IT-nb pppd[4209]: Exit.

    Read the article

  • My website dns_server_failure when using University Connection

    - by iMohammad
    My website used to open just fine in the past when I use my University connection, but now since I transfered my website to another hosting company this problem started to appear. Some times the website open and sometimes I get this alot!: Network Error (dns_server_failure) Your request could not be processed because an error occurred contacting the DNS server. The DNS server may be temporarily unavailable, or there could be a network problem. For assistance, contact your network support team. Do you have any idea? I checked using websites checking tools and my website was running just fine on any other connection , ADSL, 3g but except my University connection. Thanks in advance :) UPDATE: When I open my website using the Real IP Server it does open just fine. But with my domain nope. Also, even other websites that are hosted on my server cannot be opened too

    Read the article

  • DSL connection can't connect once disconnected

    - by Aj264
    I have setup a DSL PPPoE connection, over my cable modem, connected to my laptop via ethernet. I have saved the user name and password and set it to connect automatically. This works well when ubuntu starts and i am connected to internet. But if i try to disconnect and then reconnect, the connection wont be established. I have to restart or log out and log in, in order for ubuntu to establish the DSL connection. Any idea why this is happening? I am on ubuntu 11.10 64 bit.

    Read the article

  • Wireless connection shows up but can't connect to internet with an Intel WiFi Link 5100

    - by Eddy
    I'm using an Asus G50V and I'm completely new to ubuntu. I just installed it and can connect to the internet with a wired connection and through wireless from my windows vista that I installed wubi on, and I can connect to my wireless network, but I can't actually connect to the internet through my wireless network. Thanks in advance. Network controller is an Intel Corporation WiFi Link 5100 according to lspci if that helps Also, the connection somehow started working after I decided to unplug my ethernet cable for the third time and headed upstairs after giving up for the day.. not sure how it happened, but after restarting, the connection stopped working again.. Wifi works on 11.10, but stops working when I upgrade back to 12.04..

    Read the article

< Previous Page | 17 18 19 20 21 22 23 24 25 26 27 28  | Next Page >