Search Results

Search found 16336 results on 654 pages for 'device admin'.

Page 21/654 | < Previous Page | 17 18 19 20 21 22 23 24 25 26 27 28  | Next Page >

• Configure PL2303-based USB-to-RS232 adapter to stay awake when no active device is present

  - by casualuser

  I am resurrecting some X10 devices with the aid of a USB-to-RS232 adapter. The problem is, that the adapter only works with the Firecracker device when there is another serial device on the line (the Firecracker is a pass-through device that monitors the RTS and DTR lines to do its magic). Is the PL2303 going to sleep without a real device on the line? Is there an option or command to keep it awake? Is there a cable configuration that would make it work without a real serial device present?

  Read the article

• ext4 loopback device, Buffer I/O Error on reboot

  - by cvb

  I am trying to mount a loopback device on my ext4 formatted ssd drive. I get these errors when I reboot on Linux kernel 2.6.38.8 Buffer I/O error on device loop1, logical block 0 Here is what I do: dd if=/dev/zero of=/mnt/s/lodev bs=4096 count=250000 mkfs.ext4 /mnt/s/lodev mount -n -o loop,rw /mnt/s/lodev /mnt/test The loopback mount is successful, but on reboot I get errors as mentioned above. Even mouting with 'sync','data=writeback' does not help. I tried to losetup a device, but see the same behavior. I also reformatted the base device and created the loopback device and mounted as above, I still see these errors. I do not see them when I format them as vfat. Appreciate any suggestions on this problem.

  Read the article

• KDE Device Notifier and mounted volumes ownership and permissions

  - by nunomaltez

  Hi, When I plug an USB pen to my PC and mount the device using KDE's Device Notifier, the mounted device is owned by my user, who has write permissions. However, when I connect a USB harddisk and mount a partition in the same way, the mounted device is owned by root, and since the owner is the only one with write permissions I can't write to the disk. How do I configure the device notifier's actions to mount the HD with my user as owner, just like it mounts the USB pen? I'm using Fedora 9.

  Read the article

• Where can I find network devices in Linux? Where is a device manager (redhat enterprise linux)?

  - by bada47834

  Hello! I like to know where I can find network devices (eth0, wlan0, etc) as I could not find them under /dev even when ifconfig reported both eth0 & wlan0 Related but different question is how i can find information that MS windows devices manager provides, and what is the process of installing devices that are not installed correctly? thank you

  Read the article

• Ralink RT3060 wireless device configuration on ubuntu 12.04

  - by Stephan

  concerning How do I get a Ralink RT3060 wireless card working? I'm running Ubuntu 12.04 with a 'LWPX07 Edimax EW-7711In 150M 1T1R WL PCI Card' which has a rt3060 chip. Out of the box the card is recognized as rt2800sta. I tried solution one, that didn't work. Still the card connects to the wireless network, but it seems to slow to load any pages. Then I tried solution 2, but then the network-manager doesn't see any wireless device. $ iwconfig lo no wireless extensions. ra0 Ralink STA Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 invalid crypt:0 invalid misc:0 eth0 no wireless extensions. $ lsmod Module Size Used by rt3562sta 882296 0 $ lspci -v 05:02.0 Network controller: Ralink corp. RT3060 Wireless 802.11n 1T/1R Subsystem: Edimax Computer Co. Device 7711 Flags: bus master, slow devsel, latency 64, IRQ 23 Memory at ff9f0000 (32-bit, non-prefetchable) [size=64K] Capabilities: <access denied> Kernel driver in use: rt2860 Kernel modules: rt3562sta, rt2800pci Am I missing a configuration step? How do I tell the network card which driver to use? Thanks in advance Stephan I found the problem. As described in stevens blog http://steveswinsburg.wordpress.com/2011/03/12/how-to-install-a-d-link-dwa-525-wireless-network-card-in-ubuntu-10-04/ sudo su make && make install "You need to use ‘sudo su’ and not just ‘sudo’ so it creates the directories properly." That is the problem with the solution describe above.

  Read the article

• How can I hard reset a USB device?

  - by Cory

  I have a USB device (a modem) that is really finicky. Sometimes it works fine, but other times it refuses to connect. The only solution I have found to fix it once it gets into a bad state is to physically unplug the device and plug it back in. However, I don't always have physical access to the machine it is plugged in on, so I'm looking for a way to do this through the command line. This post suggests running: sudo modprobe -w -r usb_storage; sudo modprobe usb_storage However I get an "unknown option -w" output. This slightly modified command: sudo modprobe -r usb_storage Fails with the message FATAL: Module usb_storage is in use. If I try to kill -9 the processes marked [usb-storage] before running they refuse to die (I think because they are deeply tied to the kernel). Anyone know of a way to do this? NOTE: I cross-posted this on superuser.com as I didn't know which was more appropriate. I will delete and/or link whichever one is answered first.

  Read the article

• Clipping polygons in XNA with stencil (not using spritebatch)

  - by Blau

  The problem... i'm drawing polygons, in this case boxes, and i want clip children polygons with its parent's client area. // Class Region public void Render(GraphicsDevice Device, Camera Camera) { int StencilLevel = 0; Device.Clear( ClearOptions.Stencil, Vector4.Zero, 0, StencilLevel ); Render( Device, Camera, StencilLevel ); } private void Render(GraphicsDevice Device, Camera Camera, int StencilLevel) { Device.SamplerStates[0] = this.SamplerState; Device.Textures[0] = this.Texture; Device.RasterizerState = RasterizerState.CullNone; Device.BlendState = BlendState.AlphaBlend; Device.DepthStencilState = DepthStencilState.Default; Effect.Prepare(this, Camera ); Device.DepthStencilState = GlobalContext.GraphicsStates.IncMask; Device.ReferenceStencil = StencilLevel; foreach ( EffectPass pass in Effect.Techniques[Technique].Passes ) { pass.Apply( ); Device.DrawUserIndexedPrimitives<VertexPositionColorTexture>( PrimitiveType.TriangleList, VertexData, 0, VertexData.Length, IndexData, 0, PrimitiveCount ); } foreach ( Region child in ChildrenRegions ) { child.Render( Device, Camera, StencilLevel + 1 ); } Effect.Prepare( this, Camera ); // This does not works Device.BlendState = GlobalContext.GraphicsStates.NoWriteColor; Device.DepthStencilState = GlobalContext.GraphicsStates.DecMask; Device.ReferenceStencil = StencilLevel; // This should be +1, but in that case the last drrawed is blue and overlap all foreach ( EffectPass pass in Effect.Techniques[Technique].Passes ) { pass.Apply( ); Device.DrawUserIndexedPrimitives<VertexPositionColorTexture>( PrimitiveType.TriangleList, VertexData, 0, VertexData.Length, IndexData, 0, PrimitiveCount ); } } public static class GraphicsStates { public static BlendState NoWriteColor = new BlendState( ) { ColorSourceBlend = Blend.One, AlphaSourceBlend = Blend.One, ColorDestinationBlend = Blend.InverseSourceAlpha, AlphaDestinationBlend = Blend.InverseSourceAlpha, ColorWriteChannels1 = ColorWriteChannels.None }; public static DepthStencilState IncMask = new DepthStencilState( ) { StencilEnable = true, StencilFunction = CompareFunction.Equal, StencilPass = StencilOperation.IncrementSaturation, }; public static DepthStencilState DecMask = new DepthStencilState( ) { StencilEnable = true, StencilFunction = CompareFunction.Equal, StencilPass = StencilOperation.DecrementSaturation, }; } How can achieve this? EDIT: I've just relized that the NoWriteColors.ColorWriteChannels1 should be NoWriteColors.ColorWriteChannels. :) Now it's clipping right. Any other approach?

  Read the article

• Displaying device contacts with an indication that the contact is registered to the app

  - by Prasanna Aarthi

  We are developing a mobile app that needs to pick up device contacts, display them and indicate if the contact has already registered with this app. We have our DB in the server and the app fetches data using web services. What will be the best approach to implement the above scenario taking performance into consideration. Option 1: Every time user opens the app,fetch the contacts and send the list of email addresses to the server, check with the registered email ids and return the list of registered users in the contact list. In this approach whenever user opens the particular page, he needs to wait for few seconds to load data, but the contacts will be the latest from the device. Option 2: First time when the user opens the app, fetch contacts ,send the entire list of contacts and save it in the DB, retrieve list of registered users in the contacts then save this to local DB. From now on, data will be fetched from local DB and displayed. When a new user registers in the app, again check with records in central DB and send list of new users who are in your contacts that have registered to your app. This list will be added to local DB. and the process continues. In this case the new contacts added by user will not be updated in the app but retrieval and display of records would be quick. What would be the correct approach? In case there is a better way of doing this, please let me know.

  Read the article

• Microsoft IntelliMouse episodic pauses

  - by Rob Hills

  I have a Microsoft IntelliMouse connected via USB to a computer (directly, NOT via hub) currently running Ubuntu 11.10, but this problem also existed before we upgraded from 10.10. Every now and then (apparently randomly) the computer "pauses" for anything up to a few seconds. This usually occurs after a mouse movement and during the pause, the computer is completely unresponsive to mouse or keyboard. lsusb shows: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 002: ID 0409:0058 NEC Corp. HighSpeed Hub Bus 001 Device 004: ID 05e3:0605 Genesys Logic, Inc. USB 2.0 Hub [ednet] Bus 003 Device 013: ID 045e:001e Microsoft Corp. IntelliMouse Explorer Bus 001 Device 005: ID 04a9:1097 Canon, Inc. PIXMA iP5000 Bus 001 Device 006: ID 0a5c:200a Broadcom Corp. Bluetooth dongle Bus 001 Device 007: ID 0911:1c57 Philips Speech Processing Bus 001 Device 008: ID 04a9:2219 Canon, Inc. CanoScan 9950F so the mouse appears to be correctly identified. Syslog episodically shows the following sequence: Jan 15 11:48:32 kayes-computer kernel: [10588.512036] usb 3-1: USB disconnect, device number 10 Jan 15 11:48:33 kayes-computer kernel: [10589.248026] usb 3-1: new low speed USB device number 11 using uhci_hcd Jan 15 11:48:33 kayes-computer mtp-probe: checking bus 3, device 11: "/sys/devices/pci0000:00/0000:00:1d.1/usb3/3-1" Jan 15 11:48:33 kayes-computer kernel: [10589.448596] input: Microsoft Microsoft IntelliMouse® Explorer as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.0/input/input11 Jan 15 11:48:33 kayes-computer kernel: [10589.448706] generic-usb 0003:045E:001E.000B: input,hidraw0: USB HID v1.00 Mouse [Microsoft Microsoft IntelliMouse® Explorer] on usb-0000:00:1d.1-1/input0 Jan 15 11:48:33 kayes-computer mtp-probe: bus: 3, device: 11 was not an MTP device though I can't confirm if these are directly associated with the "pauses". Any thoughts on what might be causing this or what else I can do to diagnose the problem?

  Read the article

• ubuntu 10.04: boot error for custom compiled kernel - gave up wating for root device

  - by atharva

  Hi, I have installed lucid on my Lenevo Laptop (Y 410 series , x86 platoform) and it is working fine. Now I have compiled kernel 2.6.37 from the downloaded from the kernel tree. I followed usual procedure of compileing kernel (make menuconfig,make. make modules etc). Then I created the initrd image using mkinitramfs and updated my grub using upadate grub command. Update-grub detects the initrd image of the compiled kernel. However when I boot from this kernel it gives me following error: Gave up waiting for root device. Common problems: -Boot args (cat /proc/cmdline) -Check rootdelay= (did the system wait long enough?) -Check root= (did the system wait for the right device?) -Missing modules (cat /proc/modules; ls /dev) ALERT! root=UUID=/... does not exist and then it falls onto initramfs prompt. I have tried following solutions discussed in different ubuntu forums: 1. disable uuid and point root=/dev/sda8 (sda8 is where my kernele image resides (both default kernel and compiled one) from /etc/default/grub 2. compile kernel using CONFIG_DEVTMPFS=y suggested here Still I am unable to boot from the compile kernel. Could someone please suggest me the solution ?

  Read the article

• Unable to create suitable graphics device?

  - by kraze

  I've been following the Eye of the Dragon tutorial, which is basicly a guide to making a 2D RPG game, obviously. I recently finished the tutorial about making pop up screens in the menu and changed the screen to load as a full screen. Whenever I try and load the game it just goes black and my mouse sits there. I cannot change out of it other then with CtrlAltDel. Once i do that it says No suitable graphics card found, unable to create graphics device. I read somewhere about XNA not allowing more then one screen when any one of them is full screen. but it wasnt very informative. Anyone have any ideas whats going on and/or how to fix this? Just incase if this helps this is the code for the graphics device: public Game1() { graphics = new GraphicsDeviceManager(this); graphics.PreferredBackBufferWidth = 900; graphics.PreferredBackBufferHeight = 768; graphics.IsFullScreen = true; this.Window.Title = "Eyes of the Dragon"; Content.RootDirectory = "Content"; }

  Read the article

• Ubuntu 10.04: boot error for custom compiled kernel - gave up waiting for root device

  - by atharva

  I have installed lucid on my Lenevo Laptop (Y 410 series , x86 platform) and it is working fine. Now I have compiled kernel 2.6.37 downloaded from the kernel tree. I followed usual procedure of compiling kernel (make menuconfig, make, make modules etc). Then I created the initrd image using mkinitramfs and updated my grub using update-grub command. update-grub detects the initrd image of the compiled kernel. However when I boot from this kernel it gives me following error: Gave up waiting for root device. Common problems: -Boot args (cat /proc/cmdline) -Check rootdelay= (did the system wait long enough?) -Check root= (did the system wait for the right device?) -Missing modules (cat /proc/modules; ls /dev) ALERT! root=UUID=/... does not exist and then it falls onto initramfs prompt. I have tried following solutions discussed in different Ubuntu forums: disable uuid and point root=/dev/sda8 (sda8 is where my kernel image resides (both default kernel and compiled one) from /etc/default/grub compile kernel using CONFIG_DEVTMPFS=y suggested here Still I am unable to boot from the compile kernel. Could someone please suggest me the solution?

  Read the article

• Samba share external USB device

  - by bioShark

  I managed to share stuff from my Ubuntu 12.04 to my private network, and the data is visible from a Windows machine. I even shared a hdd that has windows on it. So everything seems to work fine. When I want to share a mounted device (USB pen drive, USB HDD... etc) however, I get from the Windows machine: Access denied on file \... I realize that this is due to the missing rights on the mounted folder. By default a mounted folder gets the equivalent of 700 : drwx------, and the owner myself. But, I can't seem to change the rights on the external device... they remain 700. Is there a special trick I need to do in order to share NTFS mounted usb devices? Thanks P.S. from this Question I see that NTFS devices can not be shared....is this true? It's a bit strange, because I have in my PC 2 HDD's with 3 NTFS partitions, and I can share them without a problem.

  Read the article

• How to show AdMob ads in real iPhone device?

  - by iPhoney

  I want to integrate AdMob ads in my iPhone app. I'm using IB way to add the view and follow AdMob's pdf guide: 1. Add AdMob group(AdMobView.h,AdMobDelegateProtocol.h,libAdMob.a) 2. Add required frameworks(AudioToolbox,MediaPlayer,MessageUI,QuartzCore) 3. Add TouchJSON group 4. Add IBSupport group(AdViewController.h,AdViewController.m) 5. Add a 320*48 UIView in IB, add NSObject and change its class to AdViewController, link AdViewController's view to the 320*48 UIView and link AdViewController's viewController to current view controller. Now the iPhone simulator can show ads from AdMob, but when I test it on real device, I get the error "AdMob: Did fail to receive ad". I've tried to add test device's UDID to testDevices array, but still get the same error. - (NSArray *)testDevices { return [NSArray arrayWithObjects: ADMOB_SIMULATOR_ID, DEVICE_UDID, nil]; } Is there any problem in the above steps? Does anybody know why can't I get the ads in real device? By the way, what should be changed to build for real for-sale app, not just for test?

  Read the article

• Why won't USB 3.0 external hard drive run at USB 3.0 speeds?

  - by jgottula

  I recently purchased a PCI Express x1 USB 3.0 controller card (containing the NEC USB 3.0 controller) with the intent of using a USB 3.0 external hard drive with my Linux box. I installed the card in an empty PCIe slot on my motherboard, connected the card to a power cable, strung a USB 3.0 cable between one of the new ports and my external HDD, and connected the HDD to a wall socket for power. Booting the system, the drive works 100% as intended, with the one exception of throughput: rather than using SuperSpeed 4.8 Gbps connectivity, it seems to be falling back to High Speed 480 Mbps USB 2.0-style throughput. Disk Utility shows it as a 480 Mbps device, and running a couple Disk Utility and dd benchmarks confirms that the drive fails to exceed ~40 MB/s (the approximate limit of USB 2.0), despite it being an SSD capable of far more than that. When I connect my USB 3.0 HDD, dmesg shows this: [ 3923.280018] usb 3-2: new high speed USB device using ehci_hcd and address 6 where I would expect to find this: [ 3923.280018] usb 3-2: new SuperSpeed USB device using xhci_hcd and address 6 My system was running on kernel 2.6.35-25-generic at the time. Then, I stumbled upon this forum thread by an individual who found that a bug, which was present in kernels prior to 2.6.37-rc5, could be the culprit for this type of problem. Consequently, I installed the 2.6.37-generic mainline Ubuntu kernel to determine if the problem would go away. It didn't, so I tried 2.6.38-rc3-generic, and even the 2.6.38 nightly from 2010.02.01, to no avail. In short, I'm trying to determine why, with USB 3.0 support in the kernel, my USB 3.0 drive fails to run at full SuperSpeed throughput. See the comments under this question for additional details. Output that might be relevant to the problem (when booting from 2.6.38-rc3): Relevant lines from dmesg: [ 19.589491] xhci_hcd 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 19.589512] xhci_hcd 0000:03:00.0: setting latency timer to 64 [ 19.589516] xhci_hcd 0000:03:00.0: xHCI Host Controller [ 19.589623] xhci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 12 [ 19.650492] xhci_hcd 0000:03:00.0: irq 17, io mem 0xf8100000 [ 19.650556] xhci_hcd 0000:03:00.0: irq 47 for MSI/MSI-X [ 19.650560] xhci_hcd 0000:03:00.0: irq 48 for MSI/MSI-X [ 19.650563] xhci_hcd 0000:03:00.0: irq 49 for MSI/MSI-X [ 19.653946] xHCI xhci_add_endpoint called for root hub [ 19.653948] xHCI xhci_check_bandwidth called for root hub Relevant section of sudo lspci -v: 03:00.0 USB Controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 03) (prog-if 30) Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at f8100000 (64-bit, non-prefetchable) [size=8K] Capabilities: [50] Power Management version 3 Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+ Capabilities: [90] MSI-X: Enable+ Count=8 Masked- Capabilities: [a0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [140] Device Serial Number ff-ff-ff-ff-ff-ff-ff-ff Capabilities: [150] #18 Kernel driver in use: xhci_hcd Kernel modules: xhci-hcd Relevant section of sudo lsusb -v: Bus 012 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 3.00 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 3 bMaxPacketSize0 9 idVendor 0x1d6b Linux Foundation idProduct 0x0003 3.0 root hub bcdDevice 2.06 iManufacturer 3 Linux 2.6.38-020638rc3-generic xhci_hcd iProduct 2 xHCI Host Controller iSerial 1 0000:03:00.0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 25 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 9 Hub bInterfaceSubClass 0 Unused bInterfaceProtocol 0 Full speed (or root) hub iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0004 1x 4 bytes bInterval 12 Hub Descriptor: bLength 9 bDescriptorType 41 nNbrPorts 4 wHubCharacteristic 0x0009 Per-port power switching Per-port overcurrent protection TT think time 8 FS bits bPwrOn2PwrGood 10 * 2 milli seconds bHubContrCurrent 0 milli Ampere DeviceRemovable 0x00 PortPwrCtrlMask 0xff Hub Port Status: Port 1: 0000.0100 power Port 2: 0000.0100 power Port 3: 0000.0100 power Port 4: 0000.0100 power Device Status: 0x0003 Self Powered Remote Wakeup Enabled Full, non-verbose lsusb: Bus 012 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 011 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 010 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 009 Device 003: ID 04d9:0702 Holtek Semiconductor, Inc. Bus 009 Device 002: ID 046d:c068 Logitech, Inc. G500 Laser Mouse Bus 009 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 006: ID 174c:5106 ASMedia Technology Inc. Bus 003 Device 004: ID 0bda:0151 Realtek Semiconductor Corp. Mass Storage Device (Multicard Reader) Bus 003 Device 002: ID 058f:6366 Alcor Micro Corp. Multi Flash Reader Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 006: ID 1687:0163 Kingmax Digital Inc. Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 046d:081b Logitech, Inc. Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Full output: full dmesg full lspci full lsusb

  Read the article

• Openfire Installation Issue - Can't Login to admin panel

  - by Lobe

  I am trying to get Openfire to install on an Ubuntu virtual machine, however upon completing the web based installer, I am unable to login to the admin panel. So far I: downloaded debian installer Installed using stock options Added database and built the structure using supplied sql file Completed web based installer I am now trying to login using username: admin and my password, however I constantly get a wrong username/password error. There is a record generated in the MySQL DB showing the admin user with an encrypted password, and changing to an unencoded password doesn't work. Can anyone help pinpoint the problem here? Thanks

  Read the article

• ADMIN$ and other shares not working remotely on XP machines

  - by makerofthings7

  I'm trying to use ADMT to migrate several XP machines to a new domain and the utility (nor command line) is able to access the admin$ share or any drive share. I've added the required registry key (HKCurrent\Services\LanMan\Param) for both servers and workstation admin sharing, rebooted the PC and still am unable to access it. How can I access the admin share on these PCs? If it helps, this machine used to have McAfee installed, and the Windows firewall enabled. I stoppped both of them and the machine is still not allowing me to access it remotely by a drive$ share.

  Read the article

• (12)Cannot allocate memory: couldn't spawn child process: /usr/lib/cgi-bin/mailman/admin

  - by virtuallight

  Hi, I'm trying to install mailman + postfix + apache2 on a VPS running Ubuntu 8.10. I think I got it all according to the official Ubuntu docs. I'm getting this error though when trying to access mailman's admin page. [Wed Jun 09 21:36:02 2010] [error] [client 77.65.61.4] (12)Cannot allocate memory: couldn't create child process: 12: admin [Wed Jun 09 21:36:02 2010] [error] [client 77.65.61.4] (12)Cannot allocate memory: couldn't spawn child process: /usr/lib/cgi-bin/mailman/admin I have no idea where the problem might be. Someone please help me :)

  Read the article

• IOGEAR KVM cannot reset admin account

  - by George Horlacher

  According to the manual you can do a cold reset by holding the reset button in for 3 seconds. This does seem to reset it but the username and password are not reset... I've tried the keyboard hotkeys - Num-Lock and minus sign (-) to get into hotkey mode and then use the "r" and "" to reset to factory defaults but that doesnt seem to do anything either. It just reverts to User1. I'm not sure what the default admin username should be but admin doesnt seem to work I need to get to the admin menu to name the ports but cannot get access. Any ideas? Using GCS1758 manual with no luck.

  Read the article

• Portable scripting language for a multi-server admin?

  - by Aaron

  Please Note: Portable as in portableapps.com, not the traditional definition. Originally posted on stackoverflow.com, asking here at another user's suggestion. I'm a DBA and sysadmin, mostly for Windows machines running SQL Server. I'm looking for a programming/scripting language for Windows that doesn't require Admin access or an installer, needing no install process other than expanding it into a folder. My intent is to have a language for automation on which I can standardize. Up to this point, I've been using a combination of batch files and Unix shell, using sh.exe from UnxUtils but it's far from a perfect solution. I've evaluated a handful of options, all of them have at least one serious shortcoming or another. I have a strong preference for something open source or dual license, but I'm more interested in finding the right tool than anything else. Not interested that anything that relies on Cygwin or Java, but at this point I'd be fine with something that needs .NET. Requirements: Manageable footprint (1-100 files, under 30 MB installed) Run on Windows XP and Server (2003+) No installer (exe, msi) Works with external pipes, processes, and files Support for MS SQL Server or ODBC connections Bonus Points: Open Source FFI for calling functions in native DLLs GUI support (native or gtk, wx, fltk, etc) Linux, AIX, and/or OS X support Dynamic, object oriented and/or functional, interpreted or bytecode compiled; interactive development Able to package or compile scripts into executables So far I've tried: Ruby: 148 MB on disk, 23000 files Portable Python: 54 MB on disk, 2800 files Strawberry Perl: 123 MB on disk, 3600 files REBOL: Great, except closed source and no MSSQL or ODBC in free version Squeak Smalltalk: Great, except poor support for scripting ---- cut: points of clarification ---- Why all the limitations? I realize some of my criteria seem arbitrarily confining. It's primarily a product my environment. I work as a SQL Server DBA and backup Unix admin at a division of a large company. In addition to near a hundred boxes running some version or another of SQL Server on Windows, I also support the SQL Server Express Edition installs on over a thousand machines in the field. Because of our security policies, I don't login rights on every machine. Often enough, an issue comes up and I'm given local Admin for some period of time. Often enough, it's some box I've never touched and don't have my own environment setup yet. I may have temporary admin rights on the box, but I'm not the admin for the machine- I'm just the DBA. I've no interest in stepping on the toes of the Windows admins, nor do I want to take over any of their duties. If I bring up "installing" something, suddenly it becomes a matter of interest for Production Control and the Windows admins; if I'm copying up a script, no one minds. The distinction may not mean much to the readers, but if someone gets the wrong idea I've suddenly got a long wait and significant overhead before I can get the tool installed and get the problem solved. That's why I want something that can be copied and run in the manner of a portable app. What about the small footprint? My company has three divisions, each in a different geographical location, and one of them is a new acquisition. We have different production control/security policies in each division. I support our MSSQL databases in all three divisions. The field machines are spread around the US, sometimes connecting to the VPN over very slow links. Installing Ruby \using psexec has taken a long time over these connections. In these instances, the bigger time waster seems to be archives with thousands and thousands of files rather than their sheer size. You could say I'm spoiled by Unix, where the admins usually have at least some modern scripting language installed; I'd use PowerShell, but I don't know it well and more importantly it isn't everywhere I need to work. It's a regular occurrence that I need to write, deploy and execute some script on short notice on some machine I've never on which logged in. Since having Ruby or something similar installed on every machine I'll ever need to touch is effectively impossible because of the approvals, time and and Windows admin labor needed I makes more sense find a solution that allows me to work on my own terms.

  Read the article

• postfix and chdir domain.com/admin/ failed

  - by senzacionale

  root@ubuntu-server:/var/log# telnet localhost 110 Trying 127.0.0.1... Connected to localhost. Escape character is '^]'. +OK Hello there. user [email protected] +OK Password required. pass MyPasswd -ERR chdir domain.com/admin/ failed Connection closed by foreign host. and mail.log Apr 24 12:36:41 ubuntu-server pop3d: Connection, ip=[::ffff:127.0.0.1] Apr 24 12:36:58 ubuntu-server pop3d: chdir domain.com/admin/: No such file or directory what can i do? how to set up this directories? MX records are set, domain is set,...

  Read the article

• Add separate domain name to Wordpress admin area with htaccess

  - by Marc

  I have a Wordpress installation in a seperate folder on my server (meaning it is not in the root folder). I have a htaccess rewrite rule that maps Domain A to folder A. Inside folder A is the Wordpress admin folder, let's call it folder A.B. I tried mapping Domain B to folder A.B., but I can't get it to work properly. When you log in to Wordpress via /admin, you get redirected to /wp-login.php (so from folder A.B. to folder A), maybe that is where I get into trouble. So what I would like to do is this: Domain A folder A Domain B folder A.B Note that this is not for security purposes, I just like the idea of www.domainb.com instead of www.domaina.com/wp-admin. Can this be done with Wordpress?

  Read the article

• Wordpress network admin pointing to root as opposed to subdirectory

  - by Ian

  I've installed Wordpress on my nginx server in /blogs and new networks will be in /blogs/blogname. All my main site links point to example.com/blogs, but when I go to network admin the links point to http://www.example.com/wp-admin/network/ instead of http://www.example.com/blogs/wp-admin/network/ Here's the multisite section in my config: define('MULTISITE', true); define('SUBDOMAIN_INSTALL', false); $base = '/blogs'; define('DOMAIN_CURRENT_SITE', 'www.example.com'); define('PATH_CURRENT_SITE', '/'); define('SITE_ID_CURRENT_SITE', 1); define('BLOG_ID_CURRENT_SITE', 1); If I try changing PATH_CURRENT_SITE to /blogs, I get a db connection error. Thanks.

  Read the article

• Changing Admin Site URL (actually port) - how?

  - by TomTom

  I have a new install of the band new SharePoint 2010. I use host header identified site collections for everything. By default the admin site is on a random port. I would like to move the admin site to port 80, for the server name. As all sites have coded names (for example "intranet", "projects") this would allow administration via the server name - which is easier as external access does not have to remember the port number. How do I do this? I already changed the default URL, but the site (application) is still wrongly mapped. I dont find anything to change the IIS settings in the admin site. I possibly just miss it - so can anyone point me in the right direction?

  Read the article

• Openfire Installation Issue - Can't Login to admin panel

  - by Lobe

  I am trying to get Openfire to install on an Ubuntu virtual machine, however upon completing the web based installer, I am unable to login to the admin panel. So far I: downloaded Debian installer Installed using stock options Added database and built the structure using supplied SQL file Completed web based installer I am now trying to login using username: admin and my password, however I constantly get a wrong username/password error. There is a record generated in the MySQL database showing the admin user with an encrypted password, and changing to an unencoded password doesn't work. What is the problem here?

  Read the article

< Previous Page | 17 18 19 20 21 22 23 24 25 26 27 28  | Next Page >