Search Results

Search found 27819 results on 1113 pages for 'linux intel'.

Page 21/1113 | < Previous Page | 17 18 19 20 21 22 23 24 25 26 27 28  | Next Page >

  • Why doesn't the monitor output anything in Linux console mode?

    - by flypen
    I install Linux without graphics support. Previously I used a monitor with 720p support. And it can display normally. Now I change to a monitor with 1080p support. I can see BIOS and GRUB info on monitor, and kernel messages in early stages. However, the monitor says that there is no input immediately, and then I can't see anything again. It seems that it happens after something initializes. Is it related to vesafb? vesafb: mode is 1280x1024x32, linelength=5120, pages=0 vesafb: scrolling: redraw vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0 mtrr: type mismatch for 7f800000,800000 old: write-back new: write-combining mtrr: type mismatch for 7f800000,400000 old: write-back new: write-combining mtrr: type mismatch for 7f800000,200000 old: write-back new: write-combining mtrr: type mismatch for 7f800000,100000 old: write-back new: write-combining mtrr: type mismatch for 7f800000,80000 old: write-back new: write-combining mtrr: type mismatch for 7f800000,40000 old: write-back new: write-combining mtrr: type mismatch for 7f800000,20000 old: write-back new: write-combining mtrr: type mismatch for 7f800000,10000 old: write-back new: write-combining mtrr: type mismatch for 7f800000,8000 old: write-back new: write-combining mtrr: type mismatch for 7f800000,4000 old: write-back new: write-combining mtrr: type mismatch for 7f800000,2000 old: write-back new: write-combining mtrr: type mismatch for 7f800000,1000 old: write-back new: write-combining vesafb: framebuffer at 0x7f800000, mapped to 0xffffc90011380000, using 5120k, total 5120k Console: switching to colour frame buffer device 160x64 fb0: VESA VGA frame buffer device

    Read the article

  • How do I boot [embedded] linux from sd card?

    - by Brandon Yates
    I am hacking together a quick embedded linux system on a DM816x evm board. Previously I have been using TFTP and NFS to load my kernel and root filesystem to the board. I am now trying to switch over to loading everything from an SD card. I have my card partitioned such that uBoot and my kernel image are in one partition, and my rootFS in another partition. At power-on, Uboot starts correctly and successfully launches the kernel. However, the kernel is unable to mount the root file system. It appears that it doesn't recognize any SD (mmc) cards. It gives this error message. VFS: Cannot open root device "mmcblk0p2" or unknown-block(2,0) Please append a correct "root=" boot option; here are the available partitions: 1f00 256 mtdblock0 (driver?) 1f01 8 mtdblock1 (driver?) 1f02 2560 mtdblock2 (driver?) 1f03 1272 mtdblock3 (driver?) 1f04 2432 mtdblock4 (driver?) 1f05 128 mtdblock5 (driver?) 1f06 4352 mtdblock6 (driver?) 1f07 204928 mtdblock7 (driver?) 1f08 50304 mtdblock8 (driver?) Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(2,0) I feel like I'm missing something fundamental here. Why does it not recognize the root device I am trying to load from? Here is my uBoot boot script that is running: setenv bootargs console=ttyO2,115200n8 root=/dev/mmcblk0p2 rw mem=124M earlyprink vram=50M ti816xfb.vram=0:16M,1:16M,2:6M ip=off noinitrd;mmc init;fatload mmc 1 0x80009000 uImage;bootm 0x80009000

    Read the article

  • Dell XPS 15 (L502x) sound problem

    - by lauramolenaar
    I have a problem with my sound on my Dell XPS 15. First, when I had Windows 7, my sound was pretty good (I have a JBL 2.1 speaker system with Waves Maxx audio), but since I installed Ubuntu 12.04 it sounded very cheap and as if I put my laptop in a tin can. I've already tried installing alsa-hda-dkms from the alsa-daily ppa (http://ppa.launchpad.net/ubuntu-audio-dev/alsa-daily) This is my audio controller: laura@laura-XPS-L502X:~$ lspci -v | grep -A7 -i audio 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) Subsystem: Dell Device 04b6 Flags: bus master, fast devsel, latency 0, IRQ 51 Memory at f1c00000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel I hope you can help me, and you can always ask me for more information. Result of aplay -l: **** List of PLAYBACK Hardware Devices **** card 0: PCH [HDA Intel PCH], device 0: ALC665 Analog [ALC665 Analog] Subdevices: 0/1 Subdevice #0: subdevice #0 card 0: PCH [HDA Intel PCH], device 1: ALC665 Digital [ALC665 Digital] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: PCH [HDA Intel PCH], device 3: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0 Result of aplay -L: default Playback/recording through the PulseAudio sound server sysdefault:CARD=PCH HDA Intel PCH, ALC665 Analog Default Audio Device front:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog Front speakers surround40:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog 4.0 Surround output to Front and Rear speakers surround41:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog 4.1 Surround output to Front, Rear and Subwoofer speakers surround50:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog 5.0 Surround output to Front, Center and Rear speakers surround51:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog 5.1 Surround output to Front, Center, Rear and Subwoofer speakers surround71:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog 7.1 Surround output to Front, Center, Side, Rear and Woofer speakers iec958:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Digital IEC958 (S/PDIF) Digital Audio Output hdmi:CARD=PCH,DEV=0 HDA Intel PCH, HDMI 0 HDMI Audio Output dmix:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog Direct sample mixing device dmix:CARD=PCH,DEV=1 HDA Intel PCH, ALC665 Digital Direct sample mixing device dmix:CARD=PCH,DEV=3 HDA Intel PCH, HDMI 0 Direct sample mixing device dsnoop:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog Direct sample snooping device dsnoop:CARD=PCH,DEV=1 HDA Intel PCH, ALC665 Digital Direct sample snooping device dsnoop:CARD=PCH,DEV=3 HDA Intel PCH, HDMI 0 Direct sample snooping device hw:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog Direct hardware device without any conversions hw:CARD=PCH,DEV=1 HDA Intel PCH, ALC665 Digital Direct hardware device without any conversions hw:CARD=PCH,DEV=3 HDA Intel PCH, HDMI 0 Direct hardware device without any conversions plughw:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog Hardware device with all software conversions plughw:CARD=PCH,DEV=1 HDA Intel PCH, ALC665 Digital Hardware device with all software conversions plughw:CARD=PCH,DEV=3 HDA Intel PCH, HDMI 0 Hardware device with all software conversions

    Read the article

  • Intel Core i7 QuadCore on HP Pavilion dv7 Overheating Issues

    - by kellax
    I bought a brand new HP notebook: HP Pavilion dv7-6b21em BeatsAudio edition. The notebook is about 2 months old and has pretty nasty overheating problem. I mainly use it for development however i do play some games. The disturbing thing is that the computer is loud on pretty simple tasks. Here are the specs: CPU: Intel Core i7-2670QM QuadCore ( 8 threads ) @ 2.20 GHz RAM: ( 8GB ) 2x 4GB @ 1066 HDD: 1TB 7200 GPU: ATI Radeon HD 6770M 1GB Dedicated DDR OS: Windows 7 64bit Enterprise I have an external monitor runing on VGA port an 22' Samsung SyncMaster S24B300 CPU Heat Statistics Platform: rPGA 988B (Socket G2) Frequency: cca. 3000 Mhz VID: 1.1809 - 1.2059 v Revision: D2 CPUID: 0x206A7 TDP: 45.0 Wats, Lithographu: 32 nm Heat: Tj. Max: 100*C, Power 4.5 - 5.9 Wats Core #0: 63*C Load on all is about 0 to 2% Core #1: 65*C Core #2: 66*C Core #3: 67*C I opened the notebook the fan is working fine there is no dust but still right now the fan is pretty loud even tho all i have open is FireFox. When i run a game the heat jumps to whopping 90-97*C. It has not shut down due to overheating yet but the loud fan is pretty annoying considering I'm not really doing anything stressfull. Is there anything i can do to fix this is it maybe a BIOS issue ? I have all drivers updated tho to the latest. I have very few background processes running consuming bare 2GB of RAM and about 2% of CPU. I had it serviced they said there is nothing wrong with it. But i feel that a Notebook that costs 1.2k Euros cant be like this.

    Read the article

  • Intel Atom overheating in ASUS EEE Box 1501P

    - by Sergey L.
    I have had an ASUS EEE Box 1501P for just a little bit over a year. Of course it breaks 2 months after the warranty runs out. http://www.asus.com/Eee/EeeBox_PC/EeeBox_PC_EB1501P/ I have been using the box as a Home Media Center. Running mostly 24/7 often pausing a video overnight. Since last week the fan started running extremely loud. After some digging I found that the Intel Atom CPU in it is overheating and the built-in sensor is reporting temperatures way over 105°C. This got me worried, so I took the unit apart. Completely vacuumed the heat sink, oiled the fan, but the unit is still showing the same behaviour. After turning it on and just observing the hardware monitor in the BIOS the temperature slowly rises from 40°C to over 95°C in appx 5 min. I am running the newest BIOS and a lightweight Linux OPENELEC OS with XBMC on it. Now I am wondering if it could be a faulty heat sensor in the Atom. Recommended running temperature is up to 85°C, but I have not detected any performance hits when running at the above mentioned 105°C and there seem to be no software faults. How can an Atom with an attached heat sink and a fan running at full capacity even get this hot in the first place at 0 load? Aren't those things designed to generate virtually no heat? Could it be a faulty heat sensor? What shall I try to fix this? I would prefer not to damage the CPU, since it is hard fused into the motherboard and cannot be replaced. I could remove the heat pipe/heat sink, but it is getting hot, so heat is properly transferring from the CPU to the heat pipe, the fan is running at full capacity, is recently oiled and warm air is making it out of the exhaust. Edit: One more note: The North-bridge (or whatever it is called nowadays) is on the same heat pipe.

    Read the article

  • prevalent, recurring hardrive failure intel macbook from 2006/2007

    - by SimonSalman
    Hi, Long story: My MacBook's hard drive failed one year ago, just a month after its warranty ended or: a year and a month after I bought it. After about ten phone calls to Apple's service, they agreed to extend the warranty for another year, so that I got it replaced free of charge. In the mean time, I got to know that many MacBook users that experience/report hard drive failures. Every reported crash was preceded by a slowdown of system performance, an increased occurrence of the spinning beach ball wait courser, and frequent crashes of applications that used to run very robust until then. It happened (as far as I know) with MacBooks from 2006/2007. All these MacBooks additionally suffer from a recurring wearing down of their "top case". Many heavy users had to replace their HDDs three time since 2006/2007 resulting in an head crash, making it impossible to recover data (diagnosis of recovery specialists) in most but not all cases HDD was Seagate (doesn't necessarily have to be the cause, if majority of the MacBook charge contained Seagate drives) And right now (one year after my first disk crash), these symptoms are cumulating on my system, again ... Short version: prevalent hard drive failure on MacBook charge from 2006/2007 (i.e. 2.16 GHz Intel Core 2 Due) I am looking for any (preferable open source) tool for checking the hard drive condition, especially to detect the known "MacBook problem". So, that I can replace the disk on time. If any Mac user found a solution to prevent the repeated failure of heir hard drive, I would be very glad to get to known it. I really enjoy my old MacBook, but I hate to get interrupted every year by an HDD crash. BTW, the issue is already in discussion for a long time, but there seems to be no solution, so far. Thanks, Simon

    Read the article

  • Intel Ethernet Bottlenecking Internet?

    - by Donald Darma
    I'm having trouble with my internet speeds. So I just recent build a pc and everything is fine. I installed the Intel drivers and connected to the internet. It connects but I'm only half the speed I should be getting. My normal speed is 20mbps but speedtest.net is only showing 10. It can't be my ISP (which is TWC if anyone is asking) because my other devices like my laptop and my smartphone are showing 20 down. Heres my system: CPU: i5 4430 HSF: Stock cooler Mobo: Gigabyte Z87MX-D3H GPU: x2 MSI R7950-3GD5/OC BE RAM: Crucial Ballistix Tactical Tracer 8GB dual channel PSU: Silencer High Performance Power Supply 750 Watt 80+ (It's a subdivision of OCZ) HDD: Seagate Barracuda 7200RPM 3TB SSD: Samsung 840 Evo 120 GB Case: Corsair Obsidian 350D Edit: I am using the stock adapter that is on the motherboard. I know for a fact that the cable is good because I used it on my laptop and it ran fine. Its a CAT5E cable. I also ran IPERF and its giving me the same results, 10 mbps.

    Read the article

  • Intel Motherboard Lightning Victim Dies Hard

    - by Stetson RDT
    Today, I have a more hardware-related question. I have an Intel board, and I really do not know which board it is, I built the machine for a relative, but he forgot to keep the documentation. Long story short, the computer was disconnected during a lightning storm, but a lightning strike travelled in via the ethernet cable (It was directly connected to a power brick commonly seen on those long distance ISP Wireless transmitters), and the motherboard was shocked. I am attempting to get this PC going. The problem is as follows: The computer will randomly reboot, just in the middle of anything as it pleases. May load to EFI (or whatever BIOS is nowadays), may load to bootloader, may even get to the OS. But before 5 minutes is up, the system will always die. Out of curiosity, I plugged my voltmeter in to a molex connector. On the 5V side, it gets a good, consistant +5.13V. On the 12V side, it fluctuates, as follows: Upon immediate startup, it soars to 12.11-12.13V. It will now do one of two things: it will immediately jump down to 12.04-12.05V, or hover for about a minute at 12.11-12.13, then jump down. It seems the longer the voltage stays at 12.11-12.13, the shorter the machine will stay running. Also, post codes, whenever the machine locks up, but does not die hard, seem to be between "AA" and "AC". Does this make any sense to anybody? Do you all think this motherboard is salvageable? It was an expensive bugger, and I'd prefer to not replace it.

    Read the article

  • The Beginner’s Guide to Linux Disk Utilities

    - by Zainul Franciscus
    Knowing how to check the condition of your hard disk is useful to determine when to replace your hard disk. In today’s article, we will show you some Linux disk utilities to diagnose the health of your hard disk. Image by Scoobay Latest Features How-To Geek ETC The Complete List of iPad Tips, Tricks, and Tutorials The 50 Best Registry Hacks that Make Windows Better The How-To Geek Holiday Gift Guide (Geeky Stuff We Like) LCD? LED? Plasma? The How-To Geek Guide to HDTV Technology The How-To Geek Guide to Learning Photoshop, Part 8: Filters Improve Digital Photography by Calibrating Your Monitor The Brothers Mario – Epic Gangland Style Mario Brothers Movie Trailer [Video] Score Awesome Games on the Cheap with the Humble Indie Bundle Add a Colorful Christmas Theme to Your Windows 7 Desktop This Windows Hack Changes the Blue Screen of Death to Red Edit Images Quickly in Firefox with Pixlr Grabber Zoho Writer, Sheet, and Show Now Available in Chrome Web Store

    Read the article

  • Linux multiplayer server, need some help.

    - by Viktor
    I need to write a server for a game, which is closer to action type game, so needs fast communication. There must be only one server, I'll just split the world in zones, but this is not the question. Client will be written in java using jMonkeyEngine. In my opinion I should write the server in java. I don't want to implement any low level features such as communication, reliable udp, etc. Can you suggest any java libraries that already implement this? Or maybe there is more suitable languages to implement this project (must run on linux)?

    Read the article

  • How to Configure the Linux Grub2 Boot Menu the Easy Way

    - by Trevor Bekolay
    We, like many Linux geeks, have had some trouble making the transition to Grub2, or for some of us, learning how to configure it from scratch. Fortunately, a new graphical tool has made this process easy and straightforward! Photo by e_monk. Latest Features How-To Geek ETC Internet Explorer 9 RC Now Available: Here’s the Most Interesting New Stuff Here’s a Super Simple Trick to Defeating Fake Anti-Virus Malware How to Change the Default Application for Android Tasks Stop Believing TV’s Lies: The Real Truth About "Enhancing" Images The How-To Geek Valentine’s Day Gift Guide Inspire Geek Love with These Hilarious Geek Valentines The Citroen GT – An Awesome Video Game Car Brought to Life [Video] Four Awesome TRON Legacy Themes for Chrome and Iron Anger is Illogical – Old School Style Instructional Video [Star Trek Mashup] Get the Old Microsoft Paint UI Back in Windows 7 Relax and Sleep Is a Soothing Sleep Timer Google Rolls Out Two-Factor Authentication

    Read the article

  • Low level Linux graphics

    - by math4tots
    For educational purposes, I'd like to write an application on a Linux environment that can process keyboard events and draw graphics without huge dependencies like X or SDL. I presume that this must be possible, because X and SDL are just programs themselves, so they must rely on other methods inherent to the environment. Is this understanding correct? If so, where might I learn to write such a program? My limited experience tells me that it would involve making calls to the kernel, and/or writing to special files; however, I haven't been able to find any tutorials on the matter (I am not even sure what to Google). Also, in case it is relevant, I am running Debian Squeeze on Virtualbox. I have used a netinst cd without networking, so there isn't much installed on it currently. I will install gcc, but I am hoping I can get by with nothing more.

    Read the article

  • Installing PHP extensions on Linux

    - by EmmyS
    Please bear with me; I'm a developer, not a server admin. My company wants to explore using Magento. They've handed me a pre-configured Linux server with apache and PHP installed, but when I try to run the Magento setup, it tells me that there are PHP extensions that need to be loaded. I can edit the php.ini file, but have no idea where to get the extensions or how to install them, and there's no one here who knows, either. Can anyone give me a hand? I need the PDO_MySQL, mcrypt, and GD extensions. I've searched and found sites that talk about downloading from the terminal and compiling code, but it's all way over my head. Is there an easy way to do this?

    Read the article

  • Linux Ubuntu: Updating the GRUB menu

    - by Mr X
    So apparently there are 2 versions of Linux on my laptop(I have a dual boot system with Linux and Windows 8 but Linux is the master OS). One of them uses the Kernel version 3.11.0 whose headers + source code are incompatible with my wireless driver. My laptop is a Toshiba Satellite with a Realtek RTL8188CE wireless lan.So the newer kernel version is still the first option on the menu and to get to Linux I use the "Previous versions of linux" which is running Kernel version 3.2.0-55. What can I do to update the grub menu so that Linux version with the 3.2.0-55 Kernel appears as the primary option? Do I need to get rid of/uninstall the newer kernel version? How can I do this without screwing up Linux entirely?

    Read the article

  • Linux, fdisk: change order of partitions

    - by osgx
    I have a harddrive with 24 logical partitions on it. Half of them are Linux and half are windows. Current ordering is: 3 Linux partitions; 12 windows partitions; 9 Linux partitions. In this setup, Windows can access any of partition (no limits on partition number), but Linux can't access sda16, sda17 ... Can I change numbering of partitions without moving them on disk? I want to put all Linux partitions to be <16; and windows partitions to be 16, so linux will be able to access all linux partitions. I have fdisk/sfdisk and it sees all partitions.

    Read the article

  • Unable to login to arch linux

    - by Ayodhya
    I am new to archlinux. I am using live usb for archlinux. When I booted it said not a COM32R image. I explored on Google, used Tab and choose have64 and then it booted. Now I am not able to login I used password root but it's not accepting. I also used startx but nothing happened. I am using archlinux-2014.06.01-dual iso downloaded from archlinux website. I see the the following Arch Linux Menu after boot-up Boot Arch Linux (x86_64)(NBD) Boot Arch Linux (x86_64)(NFS) Boot Arch Linux (x86_64)(HTTP) Boot Arch Linux (i686)(NBD) Boot Arch Linux (i686)(NFS) Boot Arch Linux (i686)(HTTP) Boot Existing OS I Choose First one and fourth one (NBD) for live boot and i am having the problem mentioned above.

    Read the article

  • Configure PERL DBI and DBD in Linux

    - by Balualways
    I am new to Perl and I work in a Linux OEL 5x server. I am trying to configure the Perl DB modules for Oracle connectivity (DBD and DBI modules). Can anyone help me out in the installation procedure? I had tried CPAN didn't really worked out. Any help would be appreciated. I am not quite sure I need to initialize any variables other than $LD_LIBRARY_PATH and $ORACLE_HOME These are my observations: ISSUE:: I am getting the following issue while using the DBI module to connect to Oracle: install_driver(Oracle) failed: Can't locate loadable object for module DBD::Oracle in @INC (@INC contains: /usr/lib64/perl5/site_perl/5.8.8/x86_64-linux-thread-multi /usr/lib/perl5/site_perl/5.8.8 /usr/lib/perl5/site_perl /usr/lib64/perl5/vendor_perl/5.8.8/x86_64-linux-thread-multi /usr/lib/perl5/vendor_perl/5.8.8 /usr/lib/perl5/vendor_perl /usr/lib64/perl5/5.8.8/x86_64-linux-thread-multi /usr/lib/perl5/5.8.8 .) at (eval 3) line 3 Compilation failed in require at (eval 3) line 3. Perhaps a module that DBD::Oracle requires hasn't been fully installed at connectdb.pl line 57 I had installed the DBD for oracle from /usr/lib64/perl5/5.8.8/x86_64-linux-thread-multi/DBD/DBD-Oracle-1.50 Could you please take a look into the steps and correct me if I am wrong: Observations: $ echo $LD_LIBRARY_PATH /opt/CA/UnicenterAutoSysJM/autosys/lib:/opt/CA/SharedComponents/Csam/SockAdapter/lib:/opt/CA/SharedComponents/ETPKI/lib:/opt/CA/CAlib $ echo $ORACLE_HOME /usr/local/oracle/ORA This is how I tried to install the DBD module: Download the file DBD 1.50 for Oracle Copy to /usr/lib64/perl5/5.8.8/x86_64-linux-thread-multi/DBD Untar and Makefile.PL . Message: Using DBI 1.52 (for perl 5.008008 on x86_64-linux-thread-multi) installed in /usr/lib64/perl5/vendor_perl/5.8.8/x86_64-linux-thread-multi/auto/DBI/ Configuring DBD::Oracle for perl 5.008008 on linux (x86_64-linux-thread-multi) Remember to actually *READ* the README file! Especially if you have any problems. Installing on a linux, Ver#2.6 Using Oracle in /opt/oracle/product/10.2 DEFINE _SQLPLUS_RELEASE = "1002000400" (CHAR) Oracle version 10.2.0.4 (10.2) Found /opt/oracle/product/10.2/rdbms/demo/demo_rdbms.mk Found /opt/oracle/product/10.2/rdbms/demo/demo_rdbms64.mk Found /opt/oracle/product/10.2/rdbms/lib/ins_rdbms.mk Using /opt/oracle/product/10.2/rdbms/demo/demo_rdbms.mk Your LD_LIBRARY_PATH env var is set to '/usr/local/oracle/ORA/lib:/usr/dt/lib:/usr/openwin/lib:/usr/local/oracle/ORA/ows/cartx/wodbc/1.0/util/lib:/usr/local/oracle/ORA/lib:/usr/local/sybase/OCS-12_0/lib:/usr/local/sybase/lib:/home/oracle/jdbc/jdbcoci73/lib:./' WARNING: Your LD_LIBRARY_PATH env var doesn't include '/opt/oracle/product/10.2/lib' but probably needs to. Reading /opt/oracle/product/10.2/rdbms/demo/demo_rdbms.mk Reading /usr/local/oracle/ORA/rdbms/lib/env_rdbms.mk Attempting to discover Oracle OCI build rules sh: make: command not found by executing: [make -f /opt/oracle/product/10.2/rdbms/demo/demo_rdbms.mk build ECHODO=echo ECHO=echo GENCLNTSH='echo genclntsh' CC=true OPTIMIZE= CCFLAGS= EXE=DBD_ORA_EXE OBJS=DBD_ORA_OBJ.o] WARNING: Oracle build rule discovery failed (32512) Add path to make command into your PATH environment variable. Oracle oci build prolog: [sh: make: command not found] Oracle oci build command: [] WARNING: Unable to interpret Oracle build commands from /opt/oracle/product/10.2/rdbms/demo/demo_rdbms.mk. (Will continue by using fallback approach.) Please report this to [email protected]. See README for what to include. Found header files in /opt/oracle/product/10.2/rdbms/public. client_version=10.2 DEFINE= -Wall -Wno-comment -DUTF8_SUPPORT -DORA_OCI_VERSION=\"10.2.0.4\" -DORA_OCI_102 Checking for functioning wait.ph System: perl5.008008 linux ca-build9.us.oracle.com 2.6.20-1.3002.fc6xen #1 smp thu apr 30 18:08:39 pdt 2009 x86_64 x86_64 x86_64 gnulinux Compiler: gcc -O2 -g -pipe -Wall -Wp,-D_FORTIFY_SOURCE=2 -fexceptions -fstack-protector --param=ssp-buffer-size=4 -m64 -mtune=generic -D_REENTRANT -D_GNU_SOURCE -fno-strict-aliasing -pipe -Wdeclaration-after-statement -I/usr/local/include -D_LARGEFILE_SOURCE -D_FILE_OFFSET_BITS=64 -I/usr/include/gdbm Linker: not found Sysliblist: -ldl -lm -lpthread -lnsl -lirc Oracle makefiles would have used these definitions but we override them: CC: cc CFLAGS: $(GFLAG) $(OPTIMIZE) $(CDEBUG) $(CCFLAGS) $(PFLAGS)\ $(SHARED_CFLAG) $(USRFLAGS) [$(GFLAG) -O3 $(CDEBUG) -m32 $(TRIGRAPHS_CCFLAGS) -fPIC -I/usr/local/oracle/ORA/rdbms/demo -I/usr/local/oracle/ORA/rdbms/public -I/usr/local/oracle/ORA/plsql/public -I/usr/local/oracle/ORA/network/public -DLINUX -D_GNU_SOURCE -D_LARGEFILE64_SOURCE=1 -D_LARGEFILE_SOURCE=1 -DSLTS_ENABLE -DSLMXMX_ENABLE -D_REENTRANT -DNS_THREADS -fno-strict-aliasing $(LPFLAGS) $(USRFLAGS)] build: $(CC) $(ORALIBPATH) -o $(EXE) $(OBJS) $(OCISHAREDLIBS) [ cc -L$(LIBHOME) -L/usr/local/oracle/ORA/rdbms/lib/ -o $(EXE) $(OBJS) -lclntsh $(EXPDLIBS) $(EXOSLIBS) -ldl -lm -lpthread -lnsl -lirc -ldl -lm $(USRLIBS) -lpthread] LDFLAGS: $(LDFLAGS32) [-m32 -o $@ -L/usr/local/oracle/ORA/rdbms//lib32/ -L/usr/local/oracle/ORA/lib32/ -L/usr/local/oracle/ORA/lib32/stubs/] Linking with /usr/local/oracle/ORA/rdbms/lib/defopt.o -lclntsh -ldl -lm -lpthread -lnsl -lirc -ldl -lm -lpthread [from $(DEF_OPT) $(OCISHAREDLIBS)] Checking if your kit is complete... Looks good LD_RUN_PATH=/usr/local/oracle/ORA/lib Using DBD::Oracle 1.50. Using DBD::Oracle 1.50. Using DBI 1.52 (for perl 5.008008 on x86_64-linux-thread-multi) installed in /usr/lib64/perl5/vendor_perl/5.8.8/x86_64-linux-thread-multi/auto/DBI/ Writing Makefile for DBD::Oracle Writing MYMETA.yml and MYMETA.json *** If you have problems... read all the log printed above, and the README and README.help.txt files. (Of course, you have read README by now anyway, haven't you?)

    Read the article

  • Linux does not communicate to Windows subinterface

    - by artaxerxe
    I set my NIC on Windows so that I have two interfaces: one (the first one) has IP 192.168.0.5 the other one has IP 10.10.10.1. On a Linux machine I set an interface to 10.10.10.2. On another Linux machine I set the interface to 10.10.10.3. And tried to ping those machines. Here is the result. Linux to Linux is ok. Windows to Linux also is ok. But Linux to Windows does not work. Can you help me on getting the communication between Linux and Windows? What should I do for this? I have to mention that those machines are connected through a switch. If you need any details, ask me please! Thanks in advance!

    Read the article

  • Linux Disk Setup for VMs

    - by zjherner
    Been trying to find the ideal way to setup disks/partitions for Linux guests on ESXi. Seems as though Linux is falling behind when it comes easily adding disk space. The end goal is to be able to add disk space to a Linux server without rebooting the server or taking the server offline. Ideally, I would expect adding disk to a Linux machine should be as easy as adding disk space to a Windows machine. I expand the vmdk file from vSphere Open disk mangler find the disk and extend volume. Would have to use command line tools in linux which is no big deal, but I haven't been able to find a solid way to exand filesystems on the fly. What is everyone else using for disk setups on their linux guests? Has anyone been able to acheive adding storage space to linux without downtime? Can it be done without using lvm?

    Read the article

  • Linux server cannot be pinged

    - by misamisa
    I have set up a Linux server in DMZ. There is another Windows server running in same DMZ. These two servers can be pinged via internet using my home PC. However, the another Linux server rented from a hosting service provider can only be pinged from the Windows Server and not from the Linux server (accessed via internet). So the situation is: Windows server (DMZ) ---ping--- Rented Server.....Successful Linux server (DMZ) ---ping--- Rented Server.......Unreachable Home PC ---ping--- Linux server (DMZ).......Successful Home PC ---ping--- Windows server (DMZ).....Successful When I ran tcpdump on my Linux Server(DMZ) and started ping from Rented Server, it showed that the Linux Server(DMZ) is receiving ping and replying. There is no restriction defined in hosts.deny and hosts.allow file that might cause this problem. What else should I check to get this working?

    Read the article

  • Flickering issue in external monitor when used with Acer Aspire One D260 netbook (Intel GMA 3150)

    - by seyenne
    I recently purchased a Acer netbook, Aspire One D260. It runs flawlessly. Yesterday I bought a Samsung 23" TFT with a native resolution of 1920x1080. According to the information found in the internet and my local computer dealer, the Intel chipset can handle the native resolution of the monitor. However, this is only partly the case. I use the VGA cable to connect, the monitor instantly switches to the native resolution and now the problem: Occasionally, especially the first 2 hours after booting up, I have a flickering all over the screen, sometimes the entire screen is shaking and spinning around like crazy. I figured out that lowering the resolution avoids the flicker but this helps only for some time. I can rule out that it's the monitor's problem since I found no issues with another notebook. Right now, I have no problems with the netbook, for about 30 minutes I didn't experience any issues... But I don't know for how long, it occurs without warning :-) I'm worried that if I would bring the netbook back to the dealer and explain my problem, after testing it on an external screen in the local shop, everything works just fine... And I won't get helped with the problem because I can't prove it. (I'm currently in Thailand and over here, customer service is nothing like back home in Germany) What can I do? Is this a driver related issue? (I installed the latest GPU driver) Is it because of the VGA cable? (But why does it work sometimes without any problems and with no issues on the other notebook) I monitored the GPU/CPU temperature, nothing changes really over time.. Can it simply be a faulty GPU and is a replacement justifiable? I'm really stressed now because for the time I'm writing, the flickering didn't occur... but for sure, soon or later it will happen again.. I forgot to mention, the problem also happens if the netbook runs on battery, unplugged. So the only hardware that is plugged is the TFT screen. ...........and here it comes again, flickering has just begun. NEED HELP! Thank you all for reading through this and giving any suggestions if possible. Cheers

    Read the article

  • Computer won't reboot without waiting for a while

    - by Benjamin
    I've got an unusual problem with my computer. When ever I reboot my computer it won't boot, I get a few beeps from the BIOS and nothing else, however if I wait for a few minuets the computer will boot perfectly. I tried to count the beeps and I get around 7-9 of them; the first two are noticeably closer together than the rest. [Edit: I'm now reasonably confident it's 1 long followed by 8 short beeps. That would be a display related issue: http://www.bioscentral.com/beepcodes/amibeep.htm] My BIOS is American Megatrends Inc and version P1.80, the Motherboard is an ASRock X58 Extreme (both according to dmidecode) Here's an output from LSPCI, I'm not sure what else might be useful but I can provide whatever's asked. 00:00.0 Host bridge: Intel Corporation 5520/5500/X58 I/O Hub to ESI Port (rev 13) 00:01.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 1 (rev 13) 00:03.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 3 (rev 13) 00:07.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 7 (rev 13) 00:14.0 PIC: Intel Corporation 5520/5500/X58 I/O Hub System Management Registers (rev 13) 00:14.1 PIC: Intel Corporation 5520/5500/X58 I/O Hub GPIO and Scratch Pad Registers (rev 13) 00:14.2 PIC: Intel Corporation 5520/5500/X58 I/O Hub Control Status and RAS Registers (rev 13) 00:14.3 PIC: Intel Corporation 5520/5500/X58 I/O Hub Throttle Registers (rev 13) 00:1a.0 USB controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #4 00:1a.1 USB controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #5 00:1a.2 USB controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #6 00:1a.7 USB controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #2 00:1b.0 Audio device: Intel Corporation 82801JI (ICH10 Family) HD Audio Controller 00:1c.0 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 1 00:1c.1 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 2 00:1c.5 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 6 00:1d.0 USB controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #1 00:1d.1 USB controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #2 00:1d.2 USB controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #3 00:1d.7 USB controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #1 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 90) 00:1f.0 ISA bridge: Intel Corporation 82801JIR (ICH10R) LPC Interface Controller 00:1f.2 SATA controller: Intel Corporation 82801JI (ICH10 Family) SATA AHCI Controller 00:1f.3 SMBus: Intel Corporation 82801JI (ICH10 Family) SMBus Controller 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) 02:00.0 FireWire (IEEE 1394): VIA Technologies, Inc. VT6315 Series Firewire Controller 02:00.1 IDE interface: VIA Technologies, Inc. VT6415 PATA IDE Host Controller (rev a0) 03:00.0 SATA controller: JMicron Technology Corp. JMB360 AHCI Controller (rev 02) 05:00.0 VGA compatible controller: nVidia Corporation GT200b [GeForce GTX 285] (rev a1) ff:00.0 Host bridge: Intel Corporation Xeon 5500/Core i7 QuickPath Architecture Generic Non-Core Registers (rev 05) ff:00.1 Host bridge: Intel Corporation Xeon 5500/Core i7 QuickPath Architecture System Address Decoder (rev 05) ff:02.0 Host bridge: Intel Corporation Xeon 5500/Core i7 QPI Link 0 (rev 05) ff:02.1 Host bridge: Intel Corporation Xeon 5500/Core i7 QPI Physical 0 (rev 05) ff:03.0 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller (rev 05) ff:03.1 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Target Address Decoder (rev 05) ff:03.4 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Test Registers (rev 05) ff:04.0 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 0 Control Registers (rev 05) ff:04.1 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 0 Address Registers (rev 05) ff:04.2 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 0 Rank Registers (rev 05) ff:04.3 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 0 Thermal Control Registers (rev 05) ff:05.0 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 1 Control Registers (rev 05) ff:05.1 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 1 Address Registers (rev 05) ff:05.2 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 1 Rank Registers (rev 05) ff:05.3 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 1 Thermal Control Registers (rev 05) ff:06.0 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 2 Control Registers (rev 05) ff:06.1 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 2 Address Registers (rev 05) ff:06.2 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 2 Rank Registers (rev 05) ff:06.3 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 2 Thermal Control Registers (rev 05) Update: ok I installed lm-sensors and here's the output. coretemp-isa-0000 Adapter: ISA adapter Core 0: +58.0°C (high = +80.0°C, crit = +100.0°C) Core 1: +59.0°C (high = +80.0°C, crit = +100.0°C) Core 2: +58.0°C (high = +80.0°C, crit = +100.0°C) Core 3: +57.0°C (high = +80.0°C, crit = +100.0°C) it8720-isa-0a10 Adapter: ISA adapter in0: +0.93 V (min = +0.00 V, max = +4.08 V) in1: +0.06 V (min = +0.00 V, max = +4.08 V) in2: +3.25 V (min = +0.00 V, max = +4.08 V) +5V: +2.91 V (min = +0.00 V, max = +4.08 V) in4: +3.04 V (min = +0.00 V, max = +4.08 V) in5: +2.94 V (min = +0.00 V, max = +4.08 V) in6: +2.14 V (min = +0.00 V, max = +4.08 V) 5VSB: +2.96 V (min = +0.00 V, max = +4.08 V) Vbat: +3.28 V fan1: 1869 RPM (min = 0 RPM) fan2: 0 RPM (min = 0 RPM) fan3: 0 RPM (min = 0 RPM) fan4: 1106 RPM (min = -1 RPM) fan5: 225000 RPM (min = -1 RPM) temp1: +39.0°C (low = +0.0°C, high = +127.0°C) sensor = thermistor temp2: +56.0°C (low = +0.0°C, high = +127.0°C) sensor = thermistor temp3: +127.0°C (low = +0.0°C, high = +127.0°C) sensor = thermistor cpu0_vid: +1.650 V intrusion0: ALARM If it helps here's the summery from sensors-detect Driver `it87': * ISA bus, address 0xa10 Chip `ITE IT8720F Super IO Sensors' (confidence: 9) Driver `adt7475': * Bus `NVIDIA i2c adapter 3 at 5:00.0' Busdriver `nvidia', I2C address 0x2e Chip `Analog Devices ADT7473' (confidence: 5) Driver `coretemp': * Chip `Intel digital thermal sensor' (confidence: 9)

    Read the article

  • What hardware combonation is better one with a i7-720QM processor and GeForce 310M graphics or one w

    - by Mason
    I am looking for a new laptop and the two i am deciding between is an Asus with Intel® Core™ i5-430M processor and NVIDIA GeForce GTS 360M graphics. Or a Toshiba with the Intel® Core™ i7-720QM processor and NVIDIA GeForce 310M graphics. I am looking for a computer to use for college and be able to play games on. I want to know what one I should get they are both the same price.

    Read the article

  • netbook intel GMA 3150 external monitor 1920x1080 flicker problem

    - by seyenne
    Dear all, i recently purchased a acer netbook (apsire one d260). It runs flawlessly. Yesterday I bought a samsung 23" TFT with a native resolution of 1920x1080. According to the information found in the internet and my local computer dealer, the intel chipset can handle the native resolution of the monitor. However, this is only partly the case. I use the VGA cabel to connect, the monitor instantly switches to the native resolution and now the problem: Occasionaly, especially the first 2 hours after booting up, I have a flickering all over the screen, sometimes the entire screen is shaking and spinning around like crazy. I figured out, that lowering the resolution avoids the flicker but this helps only for some time. I can rule out that it's the monitor's problem since I found no issues with another notebook. Right now, I have no problems with the netbook, for about 30 minutes I didn't experience any issues... But I don't know for how long, it occurs without warning :-) I'm worried that if I would bring the netbook back to the dealer and explain my problem, after testing it on an external screen in the local shop, everything works just fine... And I won't get helped with the problem because I can't prove it. (I'm currently in Thailand and over here, customer service is nothing like back home in Germany) What can I do? Is this a driver related issue? (I installed the latest GPU driver) Is it because of the VGA cable? (But why does it work sometimes without any problems and with no issues on the other notebook) I monitored the GPU/CPU temperature, nothing changes really over time..Can it simply be a faulty GPU and is a replacement justifiable? I'm really stressed now because for the time I'm writing, the flickering didn't occur...but for sure, soon or later it will happen again.. I Forgot to mention, the problem also happens if the netbook runs on battery, unplugged. So the only hardware that is plugged is the TFT screen. ...........and here it comes again, flickering has just begun. NEED HELP! Thank you all for reading through this and giving any suggestions if possible. Cheers

    Read the article

  • Download the ‘Getting Started with Ubuntu 12.04' Manual for Free

    - by Asian Angel
    If you or someone you know is new to Ubuntu, then the release of this free 143 page manual for the latest LTS edition of Ubuntu is the perfect download. The manual will take you from installing Ubuntu 12.04 all the way through to trouble-shooting the system if you run into problems. On the downloads page you can select a preferred language version, the specific version of Ubuntu you would like a manual for (10.04, 10.10, 11.10, and 12.04), and whether you prefer a ‘print or screen‘ version. Multiple Options Download Page for the Ubuntu Manual (Free Electronic Version) Note: Manual is in PDF format. Here is the link for those of you who prefer to use a regular print paperback copy of the manual. Purchase the ‘Getting Started with Ubuntu 12.04′ Manual Download the Official How-To Geek Trivia App for Windows 8 How to Banish Duplicate Photos with VisiPic How to Make Your Laptop Choose a Wired Connection Instead of Wireless

    Read the article

< Previous Page | 17 18 19 20 21 22 23 24 25 26 27 28  | Next Page >