Search Results

Search found 528 results on 22 pages for 'netmask'.

Page 21/22 | < Previous Page | 17 18 19 20 21 22  | Next Page >

• Again WPA Connection problem even after changed to latest version ..please help

  - by Renjith G

  I am using hostapd, wireless tools with madwifi for my wireless ap in my board. The WEP, WPA-PSK connections and communications between my board with linux and my desktop PC, Windows XP SP2 (with Olitec USB wireless) are fine. But when I configured the WPA type, the connection seems established but shows the status "TKIP - Key Absent" in the security dialog box. Anyone faced this problem? Am attaching the conf files and the connection status. In the AP side am complaining . I am using the in built radius server conf with the hostapd 0.4.7 hostapd.conf interface=ath0 driver=madwifi logger_syslog=0 logger_syslog_level=0 logger_stdout=0 logger_stdout_level=0 debug=0 eapol_key_index_workaround=1 dump_file=/tmp/hostapd.dump.0.0 ssid=Renjith G wpa wpa=1 wpa_passphrase=mypassphrase wpa_key_mgmt=WPA-EAP wpa_pairwise=TKIP CCMP wpa_group_rekey=600 macaddr_acl=2 /* commented */ ieee8021x=1 /* commented */ eap_authenticator=1 own_ip_addr=172.16.25.1 nas_identifier=renjithg.com auth_server_addr=172.16.25.1 auth_server_port=1812 auth_server_shared_secret=key1 ca_cert=/flash1/ca.crt server_cert=/flash1/server.crt eap_user_file=/etc/hostapd.eap_user hostapd.eap_user "*@renjithg.com" TLS And the commands am using are wlanconfig ath0 create wlandev wifi0 wlanmode ap iwconfig ath0 essid Renjith channel 6 ifconfig ath0 192.168.25.1 netmask 255.255.255.0 up hostapd -ddd /etc/hostapd.conf Please correct if am wrong .. Also am getting the debug messages on my AP when am connecting in my windows machine through WPA ~/wlanexe # ./hostapd -ddd /etc/hostapd.conf Configuration file: /etc/hostapd.conf Line 18: obsolete eap_authenticator used; this has been renamed to eap_server madwifi_set_iface_flags: dev_up=0 Using interface ath0 with hwaddr 00:0b:6b:33:8c:30 and ssid 'Renjith G wpa' madwifi_set_ieee8021x: enabled=1 madwifi_configure_wpa: group key cipher=1 madwifi_configure_wpa: pairwise key ciphers=0xa madwifi_configure_wpa: key management algorithms=0x1 madwifi_configure_wpa: rsn capabilities=0x0 madwifi_configure_wpa: enable WPA= 0x1 madwifi_set_iface_flags: dev_up=1 madwifi_set_privacy: enabled=1 WPA: group state machine entering state GTK_INIT GMK - hexdump(len=32): 9c 77 cd 38 5a 60 3b 16 8a 22 90 e8 65 b3 c2 86 40 5c be c3 dd 84 3e df 58 1d 16 61 1d 13 d1 f2 GTK - hexdump(len=32): 02 78 d7 d3 5d 15 e3 89 9c 62 a8 fe 8a 0f 40 28 ba dc cd bc 07 f4 59 88 1c 08 84 2b 49 3d e2 32 WPA: group state machine entering state SETKEYSDONE madwifi_set_key: alg=TKIP addr=00:00:00:00:00:00 key_idx=1 Flushing old station entries madwifi_sta_deauth: addr=ff:ff:ff:ff:ff:ff reason_code=3 Deauthenticate all stations l2_packet_receive - recvfrom: Network is down Wireless event: cmd=0x8c03 len=20 New STA WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state INITIALIZE madwifi_del_key: addr=00:0a:78:a0:0b:09 key_idx=0 WPA: 00:0a:78:a0:0b:09 WPA_PTK_GROUP entering state IDLE WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state AUTHENTICATION WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state AUTHENTICATION2 IEEE 802.1X: 4 bytes from 00:0a:78:a0:0b:09 IEEE 802.1X: version=1 type=1 length=0 Wireless event: cmd=0x8c04 len=20 madwifi_del_key: addr=00:0a:78:a0:0b:09 key_idx=0 ioctl[unknown???]: Invalid argument WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state DISCONNECTED WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state INITIALIZE madwifi_del_key: addr=00:0a:78:a0:0b:09 key_idx=0 ioctl[unknown???]: Invalid argument Wireless event: cmd=0x8c03 len=20 New STA WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state INITIALIZE madwifi_del_key: addr=00:0a:78:a0:0b:09 key_idx=0 WPA: 00:0a:78:a0:0b:09 WPA_PTK_GROUP entering state IDLE WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state AUTHENTICATION WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state AUTHENTICATION2 IEEE 802.1X: 4 bytes from 00:0a:78:a0:0b:09 IEEE 802.1X: version=1 type=1 length=0 < Register Fail < Register Fail Wireless event: cmd=0x8c04 len=20 madwifi_del_key: addr=00:0a:78:a0:0b:09 key_idx=0 ioctl[unknown???]: Invalid argument WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state DISCONNECTED WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state INITIALIZE madwifi_del_key: addr=00:0a:78:a0:0b:09 key_idx=0 ioctl[unknown???]: Invalid argument Wireless event: cmd=0x8c03 len=20 New STA WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state INITIALIZE madwifi_del_key: addr=00:0a:78:a0:0b:09 key_idx=0 WPA: 00:0a:78:a0:0b:09 WPA_PTK_GROUP entering state IDLE WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state AUTHENTICATION WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state AUTHENTICATION2 IEEE 802.1X: 4 bytes from 00:0a:78:a0:0b:09 IEEE 802.1X: version=1 type=1 length=0 NOW am getting the following error message with latest tools. *This is the latest error messages..please refer this only..* ~/wlanexe # ./hostapd -ddd /etc/hostapd.conf TLS: Trusted root certificate(s) loaded madwifi_set_iface_flags: dev_up=0 madwifi_set_privacy: enabled=0 BSS count 1, BSSID mask ff:ff:ff:ff:ff:ff (0 bits) Flushing old station entries madwifi_sta_deauth: addr=ff:ff:ff:ff:ff:ff reason_code=3 ioctl[IEEE80211_IOCTL_SETMLME]: Invalid argument madwifi_sta_deauth: Failed to deauth STA (addr ff:ff:ff:ff:ff:ff reason 3) Could not connect to kernel driver. Deauthenticate all stations madwifi_sta_deauth: addr=ff:ff:ff:ff:ff:ff reason_code=2 ioctl[IEEE80211_IOCTL_SETMLME]: Invalid argument madwifi_sta_deauth: Failed to deauth STA (addr ff:ff:ff:ff:ff:ff reason 2) madwifi_set_privacy: enabled=0 madwifi_del_key: addr=00:00:00:00:00:00 key_idx=0 madwifi_del_key: addr=00:00:00:00:00:00 key_idx=1 madwifi_del_key: addr=00:00:00:00:00:00 key_idx=2 madwifi_del_key: addr=00:00:00:00:00:00 key_idx=3 Using interface ath0 with hwaddr 00:0b:6b:33:8c:30 and ssid 'RenjithGwpa' SSID - hexdump_ascii(len=11): 52 65 6e 6a 69 74 68 47 77 70 61 RenjithGwpa PSK (ASCII passphrase) - hexdump_ascii(len=12): 6d 79 70 61 73 73 70 68 72 61 73 65 mypassphrase PSK (from passphrase) - hexdump(len=32): a6 55 3e 76 94 8b d9 81 a1 22 5e 24 29 83 33 86 11 a8 7e 93 19 7c a9 ab ab cc 12 58 37 e5 35 b6 RADIUS local address: 172.16.25.1:1024 madwifi_set_ieee8021x: enabled=1 madwifi_configure_wpa: group key cipher=1 madwifi_configure_wpa: pairwise key ciphers=0xa madwifi_configure_wpa: key management algorithms=0x1 madwifi_configure_wpa: rsn capabilities=0x0 madwifi_configure_wpa: enable WPA=0x1 WPA: group state machine entering state GTK_INIT (VLAN-ID 0) GMK - hexdump(len=32): [REMOVED] GTK - hexdump(len=32): [REMOVED] WPA: group state machine entering state SETKEYSDONE (VLAN-ID 0) madwifi_set_key: alg=TKIP addr=00:00:00:00:00:00 key_idx=1 madwifi_set_privacy: enabled=1 madwifi_set_iface_flags: dev_up=1 ath0: Setup of interface done. l2_packet_receive - recvfrom: Network is down Wireless event: cmd=0x8b1a len=24 Wireless event: cmd=0x8c03 len=20 New STA ioctl[unknown???]: Invalid argument madwifi_process_wpa_ie: Failed to get WPA/RSN IE Failed to get WPA/RSN information element. Data frame from not associated STA 00:0a:78:a0:0b:09 Wireless event: cmd=0x8c04 len=20 Wireless event: cmd=0x8c03 len=20 New STA ioctl[unknown???]: Invalid argument madwifi_process_wpa_ie: Failed to get WPA/RSN IE Failed to get WPA/RSN information element. Data frame from not associated STA 00:0a:78:a0:0b:09 Data frame from not associated STA 00:0a:78:a0:0b:09 Data frame from not associated STA 00:0a:78:a0:0b:09 Wireless event: cmd=0x8c04 len=20 Wireless event: cmd=0x8c03 len=20 New STA ioctl[unknown???]: Invalid argument madwifi_process_wpa_ie: Failed to get WPA/RSN IE Failed to get WPA/RSN information element. Data frame from not associated STA 00:0a:78:a0:0b:09

  Read the article

• Connecting a LAN to an OpenVPN server via a windows 7 client gateway

  - by user705142

  I've got OpenVPN set up between my windows 7 client and linux server. The goal is that I'll get secure access to a webapp running on the server from any computer on the client LAN. I'm using ccd to assign static ip addresses to each client connection, with key authentication. It's working on my client machine (10.83.41.9), and when you go to the gateway IP address (10.83.41.1), it loads up the webapp. Now I really need the other computers on the client LAN to be able to connect to the webapp as well, via the windows machine. The client has a static IP address of 192.168.2.100 on the LAN, and I've enabled IP forwarding in windows (confirmed by ipconfig /all). In my router I've forwarded 10.83.41.1 / 255.255.255.255 to 192.168.2.100. In server.conf I have.. route 192.168.2.0 255.255.255.0 And in the office ccd.. ifconfig-push 10.83.41.9 10.83.41.10 iroute 192.168.2.0 255.255.255.0 The client log is as follows: Thu Mar 15 20:19:56 2012 OpenVPN 2.2.2 Win32-MSVC++ [SSL] [LZO2] [PKCS11] built on Dec 15 2011 Thu Mar 15 20:19:56 2012 NOTE: OpenVPN 2.1 requires '--script-security 2' or higher to call user-defined scripts or executables Thu Mar 15 20:19:56 2012 Control Channel Authentication: using 'ta.key' as a OpenVPN static key file Thu Mar 15 20:19:56 2012 Outgoing Control Channel Authentication: Using 160 bit message hash 'SHA1' for HMAC authentication Thu Mar 15 20:19:56 2012 Incoming Control Channel Authentication: Using 160 bit message hash 'SHA1' for HMAC authentication Thu Mar 15 20:19:56 2012 LZO compression initialized Thu Mar 15 20:19:56 2012 Control Channel MTU parms [ L:1558 D:166 EF:66 EB:0 ET:0 EL:0 ] Thu Mar 15 20:19:56 2012 Socket Buffers: R=[8192->8192] S=[64512->64512] Thu Mar 15 20:19:56 2012 Data Channel MTU parms [ L:1558 D:1450 EF:58 EB:135 ET:0 EL:0 AF:3/1 ] Thu Mar 15 20:19:56 2012 Local Options hash (VER=V4): '9e7066d2' Thu Mar 15 20:19:56 2012 Expected Remote Options hash (VER=V4): '162b04de' Thu Mar 15 20:19:56 2012 UDPv4 link local: [undef] Thu Mar 15 20:19:56 2012 UDPv4 link remote: 111.65.224.202:1194 Thu Mar 15 20:19:56 2012 TLS: Initial packet from 111.65.224.202:1194, sid=ceb04c22 8cc6d151 Thu Mar 15 20:19:56 2012 VERIFY OK: depth=1, /C=NZ/O=XXX./CN=XXX Thu Mar 15 20:19:56 2012 VERIFY OK: nsCertType=SERVER Thu Mar 15 20:19:56 2012 VERIFY OK: depth=0, /C=NZ/O=XXX./CN=XXX Thu Mar 15 20:19:56 2012 Replay-window backtrack occurred [1] Thu Mar 15 20:19:56 2012 Data Channel Encrypt: Cipher 'AES-256-CBC' initialized with 256 bit key Thu Mar 15 20:19:56 2012 Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Thu Mar 15 20:19:56 2012 Data Channel Decrypt: Cipher 'AES-256-CBC' initialized with 256 bit key Thu Mar 15 20:19:56 2012 Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Thu Mar 15 20:19:56 2012 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 1024 bit RSA Thu Mar 15 20:19:56 2012 [server] Peer Connection Initiated with 111.65.224.202:1194 Thu Mar 15 20:19:58 2012 SENT CONTROL [server]: 'PUSH_REQUEST' (status=1) Thu Mar 15 20:19:59 2012 PUSH: Received control message: 'PUSH_REPLY,route 10.83.41.1,topology net30,ping 10,ping-restart 120,ifconfig 10.83.41.9 10.83.41.10' Thu Mar 15 20:19:59 2012 OPTIONS IMPORT: timers and/or timeouts modified Thu Mar 15 20:19:59 2012 OPTIONS IMPORT: --ifconfig/up options modified Thu Mar 15 20:19:59 2012 OPTIONS IMPORT: route options modified Thu Mar 15 20:19:59 2012 ROUTE default_gateway=192.168.2.1 Thu Mar 15 20:19:59 2012 TAP-WIN32 device [OpenVPN] opened: \\.\Global\{B32D85C9-1942-42E2-80BA-7E0B5BB5185F}.tap Thu Mar 15 20:19:59 2012 TAP-Win32 Driver Version 9.9 Thu Mar 15 20:19:59 2012 TAP-Win32 MTU=1500 Thu Mar 15 20:19:59 2012 Notified TAP-Win32 driver to set a DHCP IP/netmask of 10.83.41.9/255.255.255.252 on interface {B32D85C9-1942-42E2-80BA-7E0B5BB5185F} [DHCP-serv: 10.83.41.10, lease-time: 31536000] Thu Mar 15 20:19:59 2012 Successful ARP Flush on interface [45] {B32D85C9-1942-42E2-80BA-7E0B5BB5185F} Thu Mar 15 20:20:04 2012 TEST ROUTES: 1/1 succeeded len=1 ret=1 a=0 u/d=up Thu Mar 15 20:20:04 2012 C:\WINDOWS\system32\route.exe ADD 10.83.41.1 MASK 255.255.255.255 10.83.41.10 Thu Mar 15 20:20:04 2012 ROUTE: CreateIpForwardEntry succeeded with dwForwardMetric1=30 and dwForwardType=4 Thu Mar 15 20:20:04 2012 Route addition via IPAPI succeeded [adaptive] Thu Mar 15 20:20:04 2012 Initialization Sequence Completed From the other machines I can ping 192.169.2.100, but not 10.83.41.1. In the how-to, it mentions "Make sure your network interface is in promiscuous mode." as well. I can't find in the windows network config, so this may or may not be part of it. Ideally this would be achieved without any special configuration the other LAN computers. Not sure how far I'm going to get on my own at this point, any ideas? Is there something I'm missing, or anything I should need to know?

  Read the article

• Cisco ASA 5505 - L2TP over IPsec

  - by xraminx

  I have followed this document on cisco site to set up the L2TP over IPsec connection. When I try to establish a VPN to ASA 5505 from my Windows XP, after I click on "connect" button, the "Connecting ...." dialog box appears and after a while I get this error message: Error 800: Unable to establish VPN connection. The VPN server may be unreachable, or security parameters may not be configured properly for this connection. ASA version 7.2(4) ASDM version 5.2(4) Windows XP SP3 Windows XP and ASA 5505 are on the same LAN for test purposes. Edit 1: There are two VLANs defined on the cisco device (the standard setup on cisco ASA5505). - port 0 is on VLAN2, outside; - and ports 1 to 7 on VLAN1, inside. I run a cable from my linksys home router (10.50.10.1) to the cisco ASA5505 router on port 0 (outside). Port 0 have IP 192.168.1.1 used internally by cisco and I have also assigned the external IP 10.50.10.206 to port 0 (outside). I run a cable from Windows XP to Cisco router on port 1 (inside). Port 1 is assigned an IP from Cisco router 192.168.1.2. The Windows XP is also connected to my linksys home router via wireless (10.50.10.141). Edit 2: When I try to establish vpn, the Cisco device real time Log viewer shows 7 entries like this: Severity:5 Date:Sep 15 2009 Time: 14:51:29 SyslogID: 713904 Destination IP = 10.50.10.141, Decription: No crypto map bound to interface... dropping pkt Edit 3: This is the setup on the router right now. Result of the command: "show run" : Saved : ASA Version 7.2(4) ! hostname ciscoasa domain-name default.domain.invalid enable password HGFHGFGHFHGHGFHGF encrypted passwd NMMNMNMNMNMNMN encrypted names name 192.168.1.200 WebServer1 name 10.50.10.206 external-ip-address ! interface Vlan1 nameif inside security-level 100 ip address 192.168.1.1 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address external-ip-address 255.0.0.0 ! interface Vlan3 no nameif security-level 50 no ip address ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! ftp mode passive dns server-group DefaultDNS domain-name default.domain.invalid object-group service l2tp udp port-object eq 1701 access-list outside_access_in remark Allow incoming tcp/http access-list outside_access_in extended permit tcp any host WebServer1 eq www access-list outside_access_in extended permit udp any any eq 1701 access-list inside_nat0_outbound extended permit ip any 192.168.1.208 255.255.255.240 access-list inside_cryptomap_1 extended permit ip interface outside interface inside pager lines 24 logging enable logging asdm informational mtu inside 1500 mtu outside 1500 ip local pool PPTP-VPN 192.168.1.210-192.168.1.220 mask 255.255.255.0 icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-524.bin no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface www WebServer1 www netmask 255.255.255.255 access-group outside_access_in in interface outside timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute http server enable http 192.168.1.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac crypto ipsec transform-set TRANS_ESP_3DES_SHA mode transport crypto ipsec transform-set TRANS_ESP_3DES_MD5 esp-3des esp-md5-hmac crypto ipsec transform-set TRANS_ESP_3DES_MD5 mode transport crypto map outside_map 1 match address inside_cryptomap_1 crypto map outside_map 1 set transform-set TRANS_ESP_3DES_MD5 crypto map outside_map interface inside crypto isakmp enable outside crypto isakmp policy 10 authentication pre-share encryption 3des hash md5 group 2 lifetime 86400 telnet timeout 5 ssh timeout 5 console timeout 0 dhcpd auto_config outside ! dhcpd address 192.168.1.2-192.168.1.33 inside dhcpd enable inside ! group-policy DefaultRAGroup internal group-policy DefaultRAGroup attributes dns-server value 192.168.1.1 vpn-tunnel-protocol IPSec l2tp-ipsec username myusername password FGHFGHFHGFHGFGFHF nt-encrypted tunnel-group DefaultRAGroup general-attributes address-pool PPTP-VPN default-group-policy DefaultRAGroup tunnel-group DefaultRAGroup ipsec-attributes pre-shared-key * tunnel-group DefaultRAGroup ppp-attributes no authentication chap authentication ms-chap-v2 ! ! prompt hostname context Cryptochecksum:a9331e84064f27e6220a8667bf5076c1 : end

  Read the article

• Set up linux box for hosting a-z

  - by microchasm

  I am in the process of reinstalling the OS on a machine that will be used to host a couple of apps for our business. The apps will be local only; access from external clients will be via vpn only. The prior setup used a hosting control panel (Plesk) for most of the admin, and I was looking at using another similar piece of software for the reinstall - but I figured I should finally learn how it all works. I can do most of the things the software would do for me, but am unclear on the symbiosis of it all. This is all an attempt to further distance myself from the land of Configuration Programmer/Programmer, if at all possible. I can't find a full walkthrough anywhere for what I'm looking for, so I thought I'd put up this question, and if people can help me on the way I will edit this with the answers, and document my progress/pitfalls. Hopefully someday this will help someone down the line. The details: CentOS 5.5 x86_64 httpd: Apache/2.2.3 mysql: 5.0.77 (to be upgraded) php: 5.1 (to be upgraded) The requirements: SECURITY!! Secure file transfer Secure client access (SSL Certs and CA) Secure data storage Virtualhosts/multiple subdomains Local email would be nice, but not critical The Steps: Download latest CentOS DVD-iso (torrent worked great for me). Install CentOS: While going through the install, I checked the Server Components option thinking I was going to be using another Plesk-like admin. In hindsight, considering I've decided to try to go my own way, this probably wasn't the best idea. Basic config: Setup users, networking/ip address etc. Yum update/upgrade. Upgrade PHP/MySQL: To upgrade PHP and MySQL to the latest versions, I had to look to another repo outside CentOS. IUS looks great and I'm happy I found it! Add IUS repository to our package manager cd /tmp wget http://dl.iuscommunity.org/pub/ius/stable/Redhat/5/x86_64/epel-release-1-1.ius.el5.noarch.rpm rpm -Uvh epel-release-1-1.ius.el5.noarch.rpm wget http://dl.iuscommunity.org/pub/ius/stable/Redhat/5/x86_64/ius-release-1-4.ius.el5.noarch.rpm rpm -Uvh ius-release-1-4.ius.el5.noarch.rpm yum list | grep -w \.ius\. # list all the packages in the IUS repository; use this to find PHP/MySQL version and libraries you want to install Remove old version of PHP and install newer version from IUS rpm -qa | grep php # to list all of the installed php packages we want to remove yum shell # open an interactive yum shell remove php-common php-mysql php-cli #remove installed PHP components install php53 php53-mysql php53-cli php53-common #add packages you want transaction solve #important!! checks for dependencies transaction run #important!! does the actual installation of packages. [control+d] #exit yum shell php -v PHP 5.3.2 (cli) (built: Apr 6 2010 18:13:45) Upgrade MySQL from IUS repository /etc/init.d/mysqld stop rpm -qa | grep mysql # to see installed mysql packages yum shell remove mysql mysql-server #remove installed MySQL components install mysql51 mysql51-server mysql51-devel transaction solve #important!! checks for dependencies transaction run #important!! does the actual installation of packages. [control+d] #exit yum shell service mysqld start mysql -v Server version: 5.1.42-ius Distributed by The IUS Community Project Upgrade instructions courtesy of IUS wiki: http://wiki.iuscommunity.org/Doc/ClientUsageGuide Install rssh (restricted shell) to provide scp and sftp access, without allowing ssh login cd /tmp wget http://dag.wieers.com/rpm/packages/rssh/rssh-2.3.2-1.2.el5.rf.x86_64.rpm rpm -ivh rssh-2.3.2-1.2.el5.rf.x86_64.rpm useradd -m -d /home/dev -s /usr/bin/rssh dev passwd dev Edit /etc/rssh.conf to grant access to SFTP to rssh users. vi /etc/rssh.conf Uncomment or add: allowscp allowsftp This allows me to connect to the machine via SFTP protocol in Transmit (my FTP program of choice; I'm sure it's similar with other FTP apps). rssh instructions appropriated (with appreciation!) from http://www.cyberciti.biz/tips/linux-unix-restrict-shell-access-with-rssh.html Set up virtual interfaces ifconfig eth1:1 192.168.1.3 up #start up the virtual interface cd /etc/sysconfig/network-scripts/ cp ifcfg-eth1 ifcfg-eth1:1 #copy default script and match name to our virtual interface vi ifcfg-eth1:1 #modify eth1:1 script #ifcfg-eth1:1 | modify so it looks like this: DEVICE=eth1:1 IPADDR=192.168.1.3 NETMASK=255.255.255.0 NETWORK=192.168.1.0 ONBOOT=yes NAME=eth1:1 Add more Virtual interfaces as needed by repeating. Because of the ONBOOT=yes line in the ifcfg-eth1:1 file, this interface will be brought up when the system boots, or the network starts/restarts. service network restart Shutting down interface eth0: [ OK ] Shutting down interface eth1: [ OK ] Shutting down loopback interface: [ OK ] Bringing up loopback interface: [ OK ] Bringing up interface eth0: [ OK ] Bringing up interface eth1: [ OK ] ping 192.168.1.3 64 bytes from 192.168.1.3: icmp_seq=1 ttl=64 time=0.105 ms And this is where I'm at. I will keep editing this as I make progress. Any tips on how to Configure virtual interfaces/ip based virtual hosts for SSL, setting up a CA, or anything else would be appreciated.

  Read the article

• DDNS Not Creating Journal (Dhcpd and Named)

  - by user130094

  * EDIT 1 * After monkeying with additional debug logging I see some log entries of interest. 27-Jul-2012 23:45:26.537 general: error: zone example.lan/IN/internal: journal rollforward failed: no more 27-Jul-2012 23:45:26.537 general: error: zone example.lan/IN/internal: not loaded due to errors. ^^^ If I can remedy the above messages I think I'll be good to go ^^^ * EDIT 2 * Grasping at straws I touched a forward and a reverse zone journal file and restarted named. Boom! Works. Despite documentation stating the files are created automatically and what I have seen before... dunno why but that did the trick. Also re-checked perms on the dir the files live in. As certain as I was, they were correct with named having rw. CentOS 6 (final) dhcpd 4.1.1-P1 named BIND 9.8.2rc1-RedHat-9.8.2-0.10.rc1.el6 Basic DHCP and DNS functionality are in place on 192.168.111.2. Clients are assigned addresses as intended and can resolve local DNS names as well as Internet names. My problem is that named's zone journal files are not created. chroot: /var/named/chroot I tried placing the zone files in various directories (/var/named/data, /var/named, /var/named/dynamic - no matter which dir with named owning and wide open perms I now get nowhere). Along the way I, at one point, got a permission denied when named tried to create the journal. Resolved the issue by: chown --recursive named:named /var/named chmod --recursive 777 /var/named The journal was then created and here's where things fell apart. I attempted to tame permissions to something more sane and broke it. Once changed and having restarted named it threw an error indicating the journal was out of sync (or something to that affect)... didn't matter since this is a new setup so I deleted it and now it is not recreated. Now though I see no errors in /var/log/messages, my chrooted /var/log/named.log, or chrooted /var/log/named.debug. I increased the debug level with 'rndc trace' - no love. Increased trace to 10, still nothing. SELinux is disabled... [root@server temp]# sestatus SELinux status: disabled dhcpd.conf... allow client-updates; ddns-update-style interim; subnet 192.168.111.0 netmask 255.255.255.224 { ... key dhcpudpate { algorithm hmac-md5; secret LDJMdPdEZED+/nN/AGO9ZA==; } zone example.lan. { primary 192.168.111.2; key dhcpudpate; } } named.conf... key dhcpudpate { algorithm hmac-md5; secret "LDJMdPdEZED+/nN/AGO9ZA=="; }; zone "example.lan" { type master; file "/var/named/dynamic/example.lan.db"; allow-transfer { none; }; allow-update { key dhcpudpate; }; notify false; check-names ignore; }; The following shows /var/log/named.log output of named starting up - no errors. 27-Jul-2012 21:33:39.349 general: info: zone 111.168.192.in-addr.arpa/IN/internal: loaded serial 2012072601 27-Jul-2012 21:33:39.349 general: info: zone example.lan/IN/internal: loaded serial 2012072501 27-Jul-2012 21:33:39.350 general: info: zone example2.lan/IN/internal: loaded serial 2012072501 27-Jul-2012 21:33:39.350 general: info: zone example3.lan/IN/internal: loaded serial 2012072601 27-Jul-2012 21:33:39.350 general: info: zone example4.lan/IN/internal: loaded serial 2012072501 27-Jul-2012 21:33:39.351 general: info: zone example5.lan/IN/internal: loaded serial 2012072501 27-Jul-2012 21:33:39.351 general: info: managed-keys-zone ./IN/internal: loaded serial 0 27-Jul-2012 21:33:39.351 general: info: zone example.lan/IN/external: loaded serial 2012072501 27-Jul-2012 21:33:39.352 general: info: zone example1.lan/IN/external: loaded serial 2012072501 27-Jul-2012 21:33:39.352 general: info: zone example2.lan/IN/external: loaded serial 2012072501 27-Jul-2012 21:33:39.352 general: info: zone example3.lan/IN/external: loaded serial 2012072501 27-Jul-2012 21:33:39.353 general: info: managed-keys-zone ./IN/external: loaded serial 0 27-Jul-2012 21:33:39.353 general: notice: running 27-Jul-2012 21:34:03.825 general: info: received control channel command 'trace 10' 27-Jul-2012 21:34:03.825 general: info: debug level is now 10 ...and /var/log/messages for a named start... Jul 27 23:02:04 server named[9124]: ---------------------------------------------------- Jul 27 23:02:04 server named[9124]: BIND 9 is maintained by Internet Systems Consortium, Jul 27 23:02:04 server named[9124]: Inc. (ISC), a non-profit 501(c)(3) public-benefit Jul 27 23:02:04 server named[9124]: corporation. Support and training for BIND 9 are Jul 27 23:02:04 server named[9124]: available at https://www.isc.org/support Jul 27 23:02:04 server named[9124]: ---------------------------------------------------- Jul 27 23:02:04 server named[9124]: adjusted limit on open files from 4096 to 1048576 Jul 27 23:02:04 server named[9124]: found 2 CPUs, using 2 worker threads Jul 27 23:02:04 server named[9124]: using up to 4096 sockets Jul 27 23:02:04 server named[9124]: loading configuration from '/etc/named.conf' Jul 27 23:02:04 server named[9124]: using default UDP/IPv4 port range: [1024, 65535] Jul 27 23:02:04 server named[9124]: using default UDP/IPv6 port range: [1024, 65535] Jul 27 23:02:04 server named[9124]: listening on IPv4 interface eth0, 192.168.111.2#53 Jul 27 23:02:04 server named[9124]: generating session key for dynamic DNS Jul 27 23:02:04 server named[9124]: sizing zone task pool based on 12 zones Jul 27 23:02:04 server named[9124]: set up managed keys zone for view internal, file 'dynamic/3bed2cb3a3acf7b6a8ef408420cc682d5520e26976d354254f528c965612054f.mkeys' Jul 27 23:02:04 server named[9124]: set up managed keys zone for view external, file 'dynamic/3c4623849a49a53911c4a3e48d8cead8a1858960bccdea7a1b978d73ec2f06d7.mkeys' Jul 27 23:02:04 server named[9124]: command channel listening on 127.0.0.1#953 What can I do to troubleshoot this further? It almost seems as though dhcpd is not triggering the update. Maybe I should troubleshoot here and, if so, how? Many thanks.

  Read the article

• Ubuntu cannot access internet, LAN is fine

  - by Kevin Southworth

  I have an Ubuntu 8.04 LTS server that is directly connected to our Comcast Business Gateway modem and I have configured it with 1 of our 5 allotted Static IPs. My other machines on our LAN can connect to this server (via ssh, web, ping, etc.) but I cannot access this server from outside our network, and this machine cannot get out to the internet either (ping google.com fails with unknown host). Here is my /etc/networking/interfaces file: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 173.162.54.19 netmask 255.255.255.248 broadcast 173.162.54.23 gateway 173.162.54.22 and my /etc/resolv.conf: nameserver 68.87.77.130 nameserver 68.87.72.130 output from sudo route -n: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 173.162.54.16 0.0.0.0 255.255.255.248 U 0 0 0 eth0 0.0.0.0 173.162.54.22 0.0.0.0 UG 100 0 0 eth0 I have a Windows 2008 machine with an almost identical Static IP, static DNS setup and it works correctly, can access it within the LAN and also from public internet, the Windows machine and the Ubuntu machine are both directly connected to the Comcast Business Gateway. I have tried rebooting Ubuntu, rebooting my Comcast modem, but nothing seems to make it work. I'm an Ubuntu noob, is there some other config I need to apply to make this work? UPDATE: Yes I am able to ping my default gateway 173.162.54.22 output of iptables --list -n: Chain INPUT (policy DROP) target prot opt source destination ufw-before-input all -- 0.0.0.0/0 0.0.0.0/0 ufw-after-input all -- 0.0.0.0/0 0.0.0.0/0 Chain FORWARD (policy DROP) target prot opt source destination ufw-before-forward all -- 0.0.0.0/0 0.0.0.0/0 ufw-after-forward all -- 0.0.0.0/0 0.0.0.0/0 Chain OUTPUT (policy ACCEPT) target prot opt source destination ufw-before-output all -- 0.0.0.0/0 0.0.0.0/0 ufw-after-output all -- 0.0.0.0/0 0.0.0.0/0 Chain ufw-after-forward (1 references) target prot opt source destination LOG all -- 0.0.0.0/0 0.0.0.0/0 limit: avg 3/min burst 10 LOG flags 0 level 4 prefix `[UFW BLOCK FORWARD]: ' RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain ufw-after-input (1 references) target prot opt source destination RETURN udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:137 RETURN udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:138 RETURN tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:139 RETURN tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:445 RETURN udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:67 RETURN udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:68 LOG all -- 0.0.0.0/0 0.0.0.0/0 limit: avg 3/min burst 10 LOG flags 0 level 4 prefix `[UFW BLOCK INPUT]: ' RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain ufw-after-output (1 references) target prot opt source destination RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain ufw-before-forward (1 references) target prot opt source destination ufw-user-forward all -- 0.0.0.0/0 0.0.0.0/0 RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain ufw-before-input (1 references) target prot opt source destination ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 ctstate RELATED,ESTABLISHED DROP all -- 0.0.0.0/0 0.0.0.0/0 ctstate INVALID ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 3 ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 4 ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 11 ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 12 ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 8 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 udp spt:67 dpt:68 ufw-not-local all -- 0.0.0.0/0 0.0.0.0/0 ACCEPT all -- 224.0.0.0/4 0.0.0.0/0 ACCEPT all -- 0.0.0.0/0 224.0.0.0/4 ufw-user-input all -- 0.0.0.0/0 0.0.0.0/0 RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain ufw-before-output (1 references) target prot opt source destination ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW,RELATED,ESTABLISHED ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 state NEW,RELATED,ESTABLISHED ufw-user-output all -- 0.0.0.0/0 0.0.0.0/0 RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain ufw-not-local (1 references) target prot opt source destination RETURN all -- 0.0.0.0/0 0.0.0.0/0 ADDRTYPE match dst-type LOCAL RETURN all -- 0.0.0.0/0 0.0.0.0/0 ADDRTYPE match dst-type MULTICAST RETURN all -- 0.0.0.0/0 0.0.0.0/0 ADDRTYPE match dst-type BROADCAST LOG all -- 0.0.0.0/0 0.0.0.0/0 limit: avg 3/min burst 10 LOG flags 0 level 4 prefix `[UFW BLOCK NOT-TO-ME]: ' DROP all -- 0.0.0.0/0 0.0.0.0/0 Chain ufw-user-forward (1 references) target prot opt source destination RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain ufw-user-input (1 references) target prot opt source destination ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:80 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:80 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:22 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:22 RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain ufw-user-output (1 references) target prot opt source destination RETURN all -- 0.0.0.0/0 0.0.0.0/0

  Read the article

• Why does my ping command (Windows) results alternate between "timeout" and "network is not reachable"?

  - by Sopalajo de Arrierez

  My Windows is in Spanish, so I will have to paste console outputs in that language (I think that translating without knowing the exact terms used in english versions could give worse results than leaving it as it appears on screen). This is the issue: when pinging a non-existent IP from a WinXP-SP3 machine (clean Windows install, just formatted), I get sometimes a "Timeout" result, and sometimes a "network is not reachable" message. This is the result of: ping 192.168.210.1 Haciendo ping a 192.168.210.1 con 32 bytes de datos: Tiempo de espera agotado para esta solicitud. Respuesta desde 80.58.67.86: Red de destino inaccesible. Respuesta desde 80.58.67.86: Red de destino inaccesible. Tiempo de espera agotado para esta solicitud. Estadísticas de ping para 192.168.210.1: Paquetes: enviados = 4, recibidos = 2, perdidos = 2 (50% perdidos), Tiempos aproximados de ida y vuelta en milisegundos: Mínimo = 0ms, Máximo = 0ms, Media = 0ms 192.168.210.1 does not exist on the network. DHCP client is enabled, and the computer gets assigned those network config by the router. My IP: 192.168.11.2 Netmask: 255.255.255.0 Gateway: 192.168.11.1 DNS: 80.58.0.33/194.224.52.36 This is the output from "route print command": =========================================================================== Rutas activas: Destino de red Máscara de red Puerta de acceso Interfaz Métrica 0.0.0.0 0.0.0.0 192.168.11.1 192.168.11.2 20 127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1 192.168.11.0 255.255.255.0 192.168.11.2 192.168.11.2 20 192.168.11.2 255.255.255.255 127.0.0.1 127.0.0.1 20 192.168.11.255 255.255.255.255 192.168.11.2 192.168.11.2 20 224.0.0.0 240.0.0.0 192.168.11.2 192.168.11.2 20 255.255.255.255 255.255.255.255 192.168.11.2 192.168.11.2 1 255.255.255.255 255.255.255.255 192.168.11.2 3 1 Puerta de enlace predeterminada: 192.168.11.1 =========================================================================== Rutas persistentes: ninguno The output of: ping 1.1.1.1 Haciendo ping a 1.1.1.1 con 32 bytes de datos: Tiempo de espera agotado para esta solicitud. Tiempo de espera agotado para esta solicitud. Tiempo de espera agotado para esta solicitud. Tiempo de espera agotado para esta solicitud. Estadísticas de ping para 1.1.1.1: Paquetes: enviados = 4, recibidos = 0, perdidos = 4 1.1.1.1 does not exist on the network. and the output of: ping 10.1.1.1 Haciendo ping a 10.1.1.1 con 32 bytes de datos: Respuesta desde 80.58.67.86: Red de destino inaccesible. Tiempo de espera agotado para esta solicitud. Tiempo de espera agotado para esta solicitud. Respuesta desde 80.58.67.86: Red de destino inaccesible. Estadísticas de ping para 10.1.1.1: Paquetes: enviados = 4, recibidos = 2, perdidos = 2 (50% perdidos), 10.1.1.1 does not exist on the network. I can do some aproximate translation of what you demand if necessary. I have another computers in the same network (WinXP-SP3 and Win7-SP1), and they have, too, this problem. Gateway (Router): Buffalo WHR-HP-GN (official Buffalo firmware, not DD-WRT). I have some Linux (Debian/Kali) machine in my network, so I tested things on it: ping 192.168.210.1 PING 192.168.210.1 (192.168.210.1) 56(84) bytes of data. From 80.58.67.86 icmp_seq=1 Packet filtered From 80.58.67.86 icmp_seq=2 Packet filtered From 80.58.67.86 icmp_seq=3 Packet filtered From 80.58.67.86 icmp_seq=4 Packet filtered to the non-existing 1.1.1.1 : ping 1.1.1.1 PING 1.1.1.1 (1.1.1.1) 56(84) bytes of data. ^C --- 1.1.1.1 ping statistics --- 153 packets transmitted, 0 received, 100% packet loss, time 153215ms (no response after waiting a few minutes). and the non-existing 10.1.1.1: ping 10.1.1.1 PING 10.1.1.1 (10.1.1.1) 56(84) bytes of data. From 80.58.67.86 icmp_seq=20 Packet filtered From 80.58.67.86 icmp_seq=22 Packet filtered From 80.58.67.86 icmp_seq=23 Packet filtered From 80.58.67.86 icmp_seq=24 Packet filtered From 80.58.67.86 icmp_seq=25 Packet filtered What is going on here? I am posing this question mainly for learning purposes, but there is another reason: when all pings are returning "timeout", it creates an %ERRORLEVEL% value of 1, but if there is someone of "Network is not reachable" type, %ERRORLEVEL% goes to 0 (no error), and this could be inappropriate for a shell script (we can not use ping to detect, for example, if the network is down due to loss of contact with the gateway).

  Read the article

• OpenVPN not connecting

  - by LandArch

  There have been a number of post similar to this, but none seem to satisfy my need. Plus I am a Ubuntu newbie. I followed this tutorial to completely set up OpenVPN on Ubuntu 12.04 server. Here is my server.conf file ################################################# # Sample OpenVPN 2.0 config file for # # multi-client server. # # # # This file is for the server side # # of a many-clients <-> one-server # # OpenVPN configuration. # # # # OpenVPN also supports # # single-machine <-> single-machine # # configurations (See the Examples page # # on the web site for more info). # # # # This config should work on Windows # # or Linux/BSD systems. Remember on # # Windows to quote pathnames and use # # double backslashes, e.g.: # # "C:\\Program Files\\OpenVPN\\config\\foo.key" # # # # Comments are preceded with '#' or ';' # ################################################# # Which local IP address should OpenVPN # listen on? (optional) local 192.168.13.8 # Which TCP/UDP port should OpenVPN listen on? # If you want to run multiple OpenVPN instances # on the same machine, use a different port # number for each one. You will need to # open up this port on your firewall. port 1194 # TCP or UDP server? proto tcp ;proto udp # "dev tun" will create a routed IP tunnel, # "dev tap" will create an ethernet tunnel. # Use "dev tap0" if you are ethernet bridging # and have precreated a tap0 virtual interface # and bridged it with your ethernet interface. # If you want to control access policies # over the VPN, you must create firewall # rules for the the TUN/TAP interface. # On non-Windows systems, you can give # an explicit unit number, such as tun0. # On Windows, use "dev-node" for this. # On most systems, the VPN will not function # unless you partially or fully disable # the firewall for the TUN/TAP interface. dev tap0 up "/etc/openvpn/up.sh br0" down "/etc/openvpn/down.sh br0" ;dev tun # Windows needs the TAP-Win32 adapter name # from the Network Connections panel if you # have more than one. On XP SP2 or higher, # you may need to selectively disable the # Windows firewall for the TAP adapter. # Non-Windows systems usually don't need this. ;dev-node MyTap # SSL/TLS root certificate (ca), certificate # (cert), and private key (key). Each client # and the server must have their own cert and # key file. The server and all clients will # use the same ca file. # # See the "easy-rsa" directory for a series # of scripts for generating RSA certificates # and private keys. Remember to use # a unique Common Name for the server # and each of the client certificates. # # Any X509 key management system can be used. # OpenVPN can also use a PKCS #12 formatted key file # (see "pkcs12" directive in man page). ca "/etc/openvpn/ca.crt" cert "/etc/openvpn/server.crt" key "/etc/openvpn/server.key" # This file should be kept secret # Diffie hellman parameters. # Generate your own with: # openssl dhparam -out dh1024.pem 1024 # Substitute 2048 for 1024 if you are using # 2048 bit keys. dh dh1024.pem # Configure server mode and supply a VPN subnet # for OpenVPN to draw client addresses from. # The server will take 10.8.0.1 for itself, # the rest will be made available to clients. # Each client will be able to reach the server # on 10.8.0.1. Comment this line out if you are # ethernet bridging. See the man page for more info. ;server 10.8.0.0 255.255.255.0 # Maintain a record of client <-> virtual IP address # associations in this file. If OpenVPN goes down or # is restarted, reconnecting clients can be assigned # the same virtual IP address from the pool that was # previously assigned. ifconfig-pool-persist ipp.txt # Configure server mode for ethernet bridging. # You must first use your OS's bridging capability # to bridge the TAP interface with the ethernet # NIC interface. Then you must manually set the # IP/netmask on the bridge interface, here we # assume 10.8.0.4/255.255.255.0. Finally we # must set aside an IP range in this subnet # (start=10.8.0.50 end=10.8.0.100) to allocate # to connecting clients. Leave this line commented # out unless you are ethernet bridging. server-bridge 192.168.13.101 255.255.255.0 192.168.13.105 192.168.13.200 # Configure server mode for ethernet bridging # using a DHCP-proxy, where clients talk # to the OpenVPN server-side DHCP server # to receive their IP address allocation # and DNS server addresses. You must first use # your OS's bridging capability to bridge the TAP # interface with the ethernet NIC interface. # Note: this mode only works on clients (such as # Windows), where the client-side TAP adapter is # bound to a DHCP client. ;server-bridge # Push routes to the client to allow it # to reach other private subnets behind # the server. Remember that these # private subnets will also need # to know to route the OpenVPN client # address pool (10.8.0.0/255.255.255.0) # back to the OpenVPN server. push "route 192.168.13.1 255.255.255.0" push "dhcp-option DNS 192.168.13.201" push "dhcp-option DOMAIN blahblah.dyndns-wiki.com" ;push "route 192.168.20.0 255.255.255.0" # To assign specific IP addresses to specific # clients or if a connecting client has a private # subnet behind it that should also have VPN access, # use the subdirectory "ccd" for client-specific # configuration files (see man page for more info). # EXAMPLE: Suppose the client # having the certificate common name "Thelonious" # also has a small subnet behind his connecting # machine, such as 192.168.40.128/255.255.255.248. # First, uncomment out these lines: ;client-config-dir ccd ;route 192.168.40.128 255.255.255.248 # Then create a file ccd/Thelonious with this line: # iroute 192.168.40.128 255.255.255.248 # This will allow Thelonious' private subnet to # access the VPN. This example will only work # if you are routing, not bridging, i.e. you are # using "dev tun" and "server" directives. # EXAMPLE: Suppose you want to give # Thelonious a fixed VPN IP address of 10.9.0.1. # First uncomment out these lines: ;client-config-dir ccd ;route 10.9.0.0 255.255.255.252 # Then add this line to ccd/Thelonious: # ifconfig-push 10.9.0.1 10.9.0.2 # Suppose that you want to enable different # firewall access policies for different groups # of clients. There are two methods: # (1) Run multiple OpenVPN daemons, one for each # group, and firewall the TUN/TAP interface # for each group/daemon appropriately. # (2) (Advanced) Create a script to dynamically # modify the firewall in response to access # from different clients. See man # page for more info on learn-address script. ;learn-address ./script # If enabled, this directive will configure # all clients to redirect their default # network gateway through the VPN, causing # all IP traffic such as web browsing and # and DNS lookups to go through the VPN # (The OpenVPN server machine may need to NAT # or bridge the TUN/TAP interface to the internet # in order for this to work properly). ;push "redirect-gateway def1 bypass-dhcp" # Certain Windows-specific network settings # can be pushed to clients, such as DNS # or WINS server addresses. CAVEAT: # http://openvpn.net/faq.html#dhcpcaveats # The addresses below refer to the public # DNS servers provided by opendns.com. ;push "dhcp-option DNS 208.67.222.222" ;push "dhcp-option DNS 208.67.220.220" # Uncomment this directive to allow different # clients to be able to "see" each other. # By default, clients will only see the server. # To force clients to only see the server, you # will also need to appropriately firewall the # server's TUN/TAP interface. ;client-to-client # Uncomment this directive if multiple clients # might connect with the same certificate/key # files or common names. This is recommended # only for testing purposes. For production use, # each client should have its own certificate/key # pair. # # IF YOU HAVE NOT GENERATED INDIVIDUAL # CERTIFICATE/KEY PAIRS FOR EACH CLIENT, # EACH HAVING ITS OWN UNIQUE "COMMON NAME", # UNCOMMENT THIS LINE OUT. ;duplicate-cn # The keepalive directive causes ping-like # messages to be sent back and forth over # the link so that each side knows when # the other side has gone down. # Ping every 10 seconds, assume that remote # peer is down if no ping received during # a 120 second time period. keepalive 10 120 # For extra security beyond that provided # by SSL/TLS, create an "HMAC firewall" # to help block DoS attacks and UDP port flooding. # # Generate with: # openvpn --genkey --secret ta.key # # The server and each client must have # a copy of this key. # The second parameter should be '0' # on the server and '1' on the clients. ;tls-auth ta.key 0 # This file is secret # Select a cryptographic cipher. # This config item must be copied to # the client config file as well. ;cipher BF-CBC # Blowfish (default) ;cipher AES-128-CBC # AES ;cipher DES-EDE3-CBC # Triple-DES # Enable compression on the VPN link. # If you enable it here, you must also # enable it in the client config file. comp-lzo # The maximum number of concurrently connected # clients we want to allow. ;max-clients 100 # It's a good idea to reduce the OpenVPN # daemon's privileges after initialization. # # You can uncomment this out on # non-Windows systems. user nobody group nogroup # The persist options will try to avoid # accessing certain resources on restart # that may no longer be accessible because # of the privilege downgrade. persist-key persist-tun # Output a short status file showing # current connections, truncated # and rewritten every minute. status openvpn-status.log # By default, log messages will go to the syslog (or # on Windows, if running as a service, they will go to # the "\Program Files\OpenVPN\log" directory). # Use log or log-append to override this default. # "log" will truncate the log file on OpenVPN startup, # while "log-append" will append to it. Use one # or the other (but not both). ;log openvpn.log ;log-append openvpn.log # Set the appropriate level of log # file verbosity. # # 0 is silent, except for fatal errors # 4 is reasonable for general usage # 5 and 6 can help to debug connection problems # 9 is extremely verbose verb 3 # Silence repeating messages. At most 20 # sequential messages of the same message # category will be output to the log. ;mute 20 I am using Windows 7 as the Client and set that up accordingly using the OpenVPN GUI. That conf file is as follows: ############################################## # Sample client-side OpenVPN 2.0 config file # # for connecting to multi-client server. # # # # This configuration can be used by multiple # # clients, however each client should have # # its own cert and key files. # # # # On Windows, you might want to rename this # # file so it has a .ovpn extension # ############################################## # Specify that we are a client and that we # will be pulling certain config file directives # from the server. client # Use the same setting as you are using on # the server. # On most systems, the VPN will not function # unless you partially or fully disable # the firewall for the TUN/TAP interface. dev tap0 up "/etc/openvpn/up.sh br0" down "/etc/openvpn/down.sh br0" ;dev tun # Windows needs the TAP-Win32 adapter name # from the Network Connections panel # if you have more than one. On XP SP2, # you may need to disable the firewall # for the TAP adapter. ;dev-node MyTap # Are we connecting to a TCP or # UDP server? Use the same setting as # on the server. proto tcp ;proto udp # The hostname/IP and port of the server. # You can have multiple remote entries # to load balance between the servers. blahblah.dyndns-wiki.com 1194 ;remote my-server-2 1194 # Choose a random host from the remote # list for load-balancing. Otherwise # try hosts in the order specified. ;remote-random # Keep trying indefinitely to resolve the # host name of the OpenVPN server. Very useful # on machines which are not permanently connected # to the internet such as laptops. resolv-retry infinite # Most clients don't need to bind to # a specific local port number. nobind # Downgrade privileges after initialization (non-Windows only) user nobody group nobody # Try to preserve some state across restarts. persist-key persist-tun # If you are connecting through an # HTTP proxy to reach the actual OpenVPN # server, put the proxy server/IP and # port number here. See the man page # if your proxy server requires # authentication. ;http-proxy-retry # retry on connection failures ;http-proxy [proxy server] [proxy port #] # Wireless networks often produce a lot # of duplicate packets. Set this flag # to silence duplicate packet warnings. ;mute-replay-warnings # SSL/TLS parms. # See the server config file for more # description. It's best to use # a separate .crt/.key file pair # for each client. A single ca # file can be used for all clients. ca "C:\\Program Files\OpenVPN\config\\ca.crt" cert "C:\\Program Files\OpenVPN\config\\ChadMWade-THINK.crt" key "C:\\Program Files\OpenVPN\config\\ChadMWade-THINK.key" # Verify server certificate by checking # that the certicate has the nsCertType # field set to "server". This is an # important precaution to protect against # a potential attack discussed here: # http://openvpn.net/howto.html#mitm # # To use this feature, you will need to generate # your server certificates with the nsCertType # field set to "server". The build-key-server # script in the easy-rsa folder will do this. ns-cert-type server # If a tls-auth key is used on the server # then every client must also have the key. ;tls-auth ta.key 1 # Select a cryptographic cipher. # If the cipher option is used on the server # then you must also specify it here. ;cipher x # Enable compression on the VPN link. # Don't enable this unless it is also # enabled in the server config file. comp-lzo # Set log file verbosity. verb 3 # Silence repeating messages ;mute 20 Not sure whats left to do.

  Read the article

• Unable to connect to Samba printer

  - by user127236

  I have a headless Ubuntu 12.04 server for files and printers. It shares files via Samba just fine. However, the HP PSC-750xi connected to the server via USB is not accessible from my Ubuntu 12.04 laptop. I can browse for it in the Printing control panel, but any attempt to authenticate my ID to the printer with my user credentials results in the error "This print share is not accessible". I have included the Samba smb.conf file below. Any help appreciated. Thanks... JGB # # Sample configuration file for the Samba suite for Debian GNU/Linux. # # # This is the main Samba configuration file. You should read the # smb.conf(5) manual page in order to understand the options listed # here. Samba has a huge number of configurable options most of which # are not shown in this example # # Some options that are often worth tuning have been included as # commented-out examples in this file. # - When such options are commented with ";", the proposed setting # differs from the default Samba behaviour # - When commented with "#", the proposed setting is the default # behaviour of Samba but the option is considered important # enough to be mentioned here # # NOTE: Whenever you modify this file you should run the command # "testparm" to check that you have not made any basic syntactic # errors. # A well-established practice is to name the original file # "smb.conf.master" and create the "real" config file with # testparm -s smb.conf.master >smb.conf # This minimizes the size of the really used smb.conf file # which, according to the Samba Team, impacts performance # However, use this with caution if your smb.conf file contains nested # "include" statements. See Debian bug #483187 for a case # where using a master file is not a good idea. # #======================= Global Settings ======================= [global] log file = /var/log/samba/log.%m passwd chat = *Enter\snew\s*\spassword:* %n\n *Retype\snew\s*\spassword:* %n\n *password\supdated\ssuccessfully* . obey pam restrictions = yes map to guest = bad user encrypt passwords = true passwd program = /usr/bin/passwd %u passdb backend = tdbsam dns proxy = no writeable = yes server string = %h server (Samba, Ubuntu) unix password sync = yes workgroup = WORKGROUP syslog = 0 panic action = /usr/share/samba/panic-action %d usershare allow guests = yes max log size = 1000 pam password change = yes ## Browsing/Identification ### # Change this to the workgroup/NT-domain name your Samba server will part of # server string is the equivalent of the NT Description field # Windows Internet Name Serving Support Section: # WINS Support - Tells the NMBD component of Samba to enable its WINS Server # wins support = no # WINS Server - Tells the NMBD components of Samba to be a WINS Client # Note: Samba can be either a WINS Server, or a WINS Client, but NOT both ; wins server = w.x.y.z # This will prevent nmbd to search for NetBIOS names through DNS. # What naming service and in what order should we use to resolve host names # to IP addresses ; name resolve order = lmhosts host wins bcast #### Networking #### # The specific set of interfaces / networks to bind to # This can be either the interface name or an IP address/netmask; # interface names are normally preferred ; interfaces = 127.0.0.0/8 eth0 # Only bind to the named interfaces and/or networks; you must use the # 'interfaces' option above to use this. # It is recommended that you enable this feature if your Samba machine is # not protected by a firewall or is a firewall itself. However, this # option cannot handle dynamic or non-broadcast interfaces correctly. ; bind interfaces only = yes #### Debugging/Accounting #### # This tells Samba to use a separate log file for each machine # that connects # Cap the size of the individual log files (in KiB). # If you want Samba to only log through syslog then set the following # parameter to 'yes'. # syslog only = no # We want Samba to log a minimum amount of information to syslog. Everything # should go to /var/log/samba/log.{smbd,nmbd} instead. If you want to log # through syslog you should set the following parameter to something higher. # Do something sensible when Samba crashes: mail the admin a backtrace ####### Authentication ####### # "security = user" is always a good idea. This will require a Unix account # in this server for every user accessing the server. See # /usr/share/doc/samba-doc/htmldocs/Samba3-HOWTO/ServerType.html # in the samba-doc package for details. # security = user # You may wish to use password encryption. See the section on # 'encrypt passwords' in the smb.conf(5) manpage before enabling. # If you are using encrypted passwords, Samba will need to know what # password database type you are using. # This boolean parameter controls whether Samba attempts to sync the Unix # password with the SMB password when the encrypted SMB password in the # passdb is changed. # For Unix password sync to work on a Debian GNU/Linux system, the following # parameters must be set (thanks to Ian Kahan <<[email protected]> for # sending the correct chat script for the passwd program in Debian Sarge). # This boolean controls whether PAM will be used for password changes # when requested by an SMB client instead of the program listed in # 'passwd program'. The default is 'no'. # This option controls how unsuccessful authentication attempts are mapped # to anonymous connections ########## Domains ########### # Is this machine able to authenticate users. Both PDC and BDC # must have this setting enabled. If you are the BDC you must # change the 'domain master' setting to no # ; domain logons = yes # # The following setting only takes effect if 'domain logons' is set # It specifies the location of the user's profile directory # from the client point of view) # The following required a [profiles] share to be setup on the # samba server (see below) ; logon path = \\%N\profiles\%U # Another common choice is storing the profile in the user's home directory # (this is Samba's default) # logon path = \\%N\%U\profile # The following setting only takes effect if 'domain logons' is set # It specifies the location of a user's home directory (from the client # point of view) ; logon drive = H: # logon home = \\%N\%U # The following setting only takes effect if 'domain logons' is set # It specifies the script to run during logon. The script must be stored # in the [netlogon] share # NOTE: Must be store in 'DOS' file format convention ; logon script = logon.cmd # This allows Unix users to be created on the domain controller via the SAMR # RPC pipe. The example command creates a user account with a disabled Unix # password; please adapt to your needs ; add user script = /usr/sbin/adduser --quiet --disabled-password --gecos "" %u # This allows machine accounts to be created on the domain controller via the # SAMR RPC pipe. # The following assumes a "machines" group exists on the system ; add machine script = /usr/sbin/useradd -g machines -c "%u machine account" -d /var/lib/samba -s /bin/false %u # This allows Unix groups to be created on the domain controller via the SAMR # RPC pipe. ; add group script = /usr/sbin/addgroup --force-badname %g ########## Printing ########## # If you want to automatically load your printer list rather # than setting them up individually then you'll need this # load printers = yes # lpr(ng) printing. You may wish to override the location of the # printcap file ; printing = bsd ; printcap name = /etc/printcap # CUPS printing. See also the cupsaddsmb(8) manpage in the # cupsys-client package. ; printing = cups ; printcap name = cups ############ Misc ############ # Using the following line enables you to customise your configuration # on a per machine basis. The %m gets replaced with the netbios name # of the machine that is connecting ; include = /home/samba/etc/smb.conf.%m # Most people will find that this option gives better performance. # See smb.conf(5) and /usr/share/doc/samba-doc/htmldocs/Samba3-HOWTO/speed.html # for details # You may want to add the following on a Linux system: # SO_RCVBUF=8192 SO_SNDBUF=8192 # socket options = TCP_NODELAY # The following parameter is useful only if you have the linpopup package # installed. The samba maintainer and the linpopup maintainer are # working to ease installation and configuration of linpopup and samba. ; message command = /bin/sh -c '/usr/bin/linpopup "%f" "%m" %s; rm %s' & # Domain Master specifies Samba to be the Domain Master Browser. If this # machine will be configured as a BDC (a secondary logon server), you # must set this to 'no'; otherwise, the default behavior is recommended. # domain master = auto # Some defaults for winbind (make sure you're not using the ranges # for something else.) ; idmap uid = 10000-20000 ; idmap gid = 10000-20000 ; template shell = /bin/bash # The following was the default behaviour in sarge, # but samba upstream reverted the default because it might induce # performance issues in large organizations. # See Debian bug #368251 for some of the consequences of *not* # having this setting and smb.conf(5) for details. ; winbind enum groups = yes ; winbind enum users = yes # Setup usershare options to enable non-root users to share folders # with the net usershare command. # Maximum number of usershare. 0 (default) means that usershare is disabled. ; usershare max shares = 100 # Allow users who've been granted usershare privileges to create # public shares, not just authenticated ones #======================= Share Definitions ======================= # Un-comment the following (and tweak the other settings below to suit) # to enable the default home directory shares. This will share each # user's home director as \\server\username ;[homes] ; comment = Home Directories ; browseable = no # By default, the home directories are exported read-only. Change the # next parameter to 'no' if you want to be able to write to them. ; read only = yes # File creation mask is set to 0700 for security reasons. If you want to # create files with group=rw permissions, set next parameter to 0775. ; create mask = 0700 # Directory creation mask is set to 0700 for security reasons. If you want to # create dirs. with group=rw permissions, set next parameter to 0775. ; directory mask = 0700 # By default, \\server\username shares can be connected to by anyone # with access to the samba server. Un-comment the following parameter # to make sure that only "username" can connect to \\server\username # The following parameter makes sure that only "username" can connect # # This might need tweaking when using external authentication schemes ; valid users = %S # Un-comment the following and create the netlogon directory for Domain Logons # (you need to configure Samba to act as a domain controller too.) ;[netlogon] ; comment = Network Logon Service ; path = /home/samba/netlogon ; guest ok = yes ; read only = yes # Un-comment the following and create the profiles directory to store # users profiles (see the "logon path" option above) # (you need to configure Samba to act as a domain controller too.) # The path below should be writable by all users so that their # profile directory may be created the first time they log on ;[profiles] ; comment = Users profiles ; path = /home/samba/profiles ; guest ok = no ; browseable = no ; create mask = 0600 ; directory mask = 0700 [printers] comment = All Printers browseable = no path = /var/spool/samba printable = yes guest ok = no read only = yes create mask = 0700 # Windows clients look for this share name as a source of downloadable # printer drivers [print$] comment = Printer Drivers browseable = yes writeable = no path = /var/lib/samba/printers # Uncomment to allow remote administration of Windows print drivers. # You may need to replace 'lpadmin' with the name of the group your # admin users are members of. # Please note that you also need to set appropriate Unix permissions # to the drivers directory for these users to have write rights in it ; write list = root, @lpadmin # A sample share for sharing your CD-ROM with others. ;[cdrom] ; comment = Samba server's CD-ROM ; read only = yes ; locking = no ; path = /cdrom ; guest ok = yes # The next two parameters show how to auto-mount a CD-ROM when the # cdrom share is accesed. For this to work /etc/fstab must contain # an entry like this: # # /dev/scd0 /cdrom iso9660 defaults,noauto,ro,user 0 0 # # The CD-ROM gets unmounted automatically after the connection to the # # If you don't want to use auto-mounting/unmounting make sure the CD # is mounted on /cdrom # ; preexec = /bin/mount /cdrom ; postexec = /bin/umount /cdrom [mediafiles] path = /media/multimedia/

  Read the article

• SOLVED Install MythTV & 11.10 on Lenovo S12 (Intel atom) with wireless

  - by keepitsimpleengineer

  This is how I installed Ubuntu 11.10 and MythTV client on my Lenovo S12 (Intel Atom) laptop and use it using WiFi (see additional notes at end). I did this because the upgrade from 11.04 bricked the laptop. Note that the partitions on the Lenovo standard disk were already in place for this installation. Also note that my LAN is setup for fixed IP addresses. Downloaded and burned 11.10 x86 Desktop Ubuntu CD Connected the power supply cord, LAN wire and the external DVD USB drive. Ran Windows XP and made sure performance level "Performance" was set and "Wireless" was enabled. Booted S12 from CD Disabled Networking from icon on upper left panel icon Edited Connections… "Wired connection 1" ? Set IP address, accepted default netmask and set gateway. Also set DNS server. Good idea to check "Connection Information" here to verify everything's O.K. Selected Install Ubuntu from the initial "Install" window Verified the three items were checked (required disk space available, plugged into a power source, & connected to the Internet) Selected Download updates while installing and third party software. Hit Continue… At wireless selected don't want to connect…WiFi…now. Continue… At Installation type, selected Something else. Continue… At partition tale, selected the ext4 Linux partition, set the mount point as "/", and marked for formatting. Here I selected the main disk (/sda) for installing the boot manager. Continue… Selected or verified my Time zone. Continue… Selected my keyboard layout. Continue… Filled in the who are you fields. Make sure password is required to sign in is checked. Continue… Chose a picture. Continue… I selected import no accounts. Continue… Wait as the Install creeps along. If your screen goes blank, tap the space bar ? apparently the screen saver/power plan does this. There are several progress bars. The longest was "Installing system", and it was the next to the last one. Installation Complete window appears, Restart Now… Wait as it stops, The screen blanks then the message "…remove…media…close tray…press enter" I just unplugged the USB DVD and hit enter… It was disheartening but the screen turned Ubuntu Purple-beige and nothing happened, so I help down the power key until it shut down, the pressed it again and the Grub Boot screen appeared. Select Ubuntu… 25.The screen went blank with the little flashing underscore cursor on it and the disk light would occasionally flash. I hit the enter key and eventuality Ubuntu started. After a somewhat long time the unity desktop appeared. 11.10, unlike earlier versions, retains the connection information. Check this by checking the network icon on the upper left applet panel. Here the touch-pad·mouse quit working and I had to reboot. It takes and extremely long time to boot, sometimes requiring several power off/ power on (cold boot). You can try to get the default network manager to work, but it might not, it didn't on mine for WiFi. Thanks to: Chris at URL here's what to do… disconnect your wired Internet connection. input your wireless information into network manager open a terminal (unity dash, top of icon totem, open, and make sure the ruler&pen icon on the bottom is selected, 2nd from left) type in "terminal". Might be a good idea to drag and drop the terminal icon to the terminal, it's easy to get rid of later. click to open a terminal, and type in: sudo rmmod acer_wmi && echo "blacklist acer_wmi" >> /etc/modprobe.d/blacklist.conf and hit enter. type in your password as asked. if you have correctly entered your WiFi information and you are near your AP, you should connect immediately if not, see the URL above ? you might need to replace "network manager" with "wicd" ? I did with 11.04. Update the new 11.10, in the upper left panel applet weird·gear icon is menu with a line about updating. It's the new way to invoke Update Manager. Your lenovo S12 (intel atom) should now run the new unity Ubuntu. Point your elbow at the ceiling and pat yourself on the back. Installing Mythbuntu Client 24.1 Open mythbuntu.org/repos (I urge you not to directly use Ubuntu Software Center for this) Install Mythbuntu Repos Save the file (in ~/Downloads, the default) Run the file ? it will update your repositories so that you will get the proper installation sources ? it will start Ubuntu Software Center to do this ? Click Install… You will need your password. Debconf window will open, select by making sure check mark is in the little box "Would you like to activate…". Forward… Which version? At the time of writing the current "Stable" version was 24.1, select 0.24.x… Forward… Read the message, then forward… Delete the downloaded file. Install synaptic (unity dash, top of icon totem, open, and make sure the ruler&pen icon on the bottom is selected, 2nd from left) type in "synaptic". Click on the synaptic icon. Ubuntu Software Center will open and allow you to install synaptic package manager. Open Synaptic (unity dash, top of icon totem, open, and make sure the ruler&pen icon on the bottom is selected, 2nd from left) type in "Synaptic". Might be a good idea to drag and drop the terminal icon to the terminal, it's easy to get rid of later. Run synaptic, read the intro, and close the intro window. Type in mythbuntu-control-centre in the Quick filter text box, and then select it "Mark for installation" by clicking on the box next to it's name. Marvel at the additional to be installed items, then select "?Mark"… At the top of the synaptic window click on the "? Apply" button. Marvel at the amount of stuff to be installed, the click on "Apply". When finished, close finished window and synaptic. Open mythbuntu-control-centre (unity dash, top of icon totem, open, and make sure the ruler&pen icon on the bottom is selected, 2nd from left) type in "mythbuntu". Might be a good idea to drag and drop the mythbuntu-control-centre icon to the terminal, it's easy to get rid of later. You can now configure and install the frontend. Go down the icon totem on the right side of the window and click as needed… System roles. ? No Backend, Desktop Frontend, and Ubuntu Desktop. Apply… & Apply changes… & Password… MySQL Configuration ? from backend ? Setup General Alt-N(ext) Alt-N(ext) Stetting Access Setup PIN code: ~~~~ Input Security key and click "Test Connection", if ?, then Apply… & Apply… {note: for some inexplicable reason, control centre hung on this, but when I restarted it, it was set properly} Graphics drivers, When I did this, only the Broadcom wireless driver showed up. I closed without doing anything. Services. I enabled SSH & Samba. Apply… & Apply… Repositories. Asked & Answered. MythExport. Pass, I believe it requires backend on the same system. Proprietary Codec Support. Check to enable, Apply… & Apply… System Updates. No action necessary, will be a part of the Ubuntu update mechanism. Themes and Artwork. For themes, I selected Enable/Update all. Apply… & Apply… Infrared & Startup behavior and Plugins. Defer until you know more. Close software centre. Open mythTV (unity dash, top of icon totem, open, and make sure the ruler&pen icon on the bottom is selected, 2nd from left) type in "mythTV". Might be a good idea to drag and drop the mythTV icon to the terminal, it's easy to get rid of later. Incorrect Group Membership. Fix this by clicking "Yes"… Log out/end. Do this by clicking "Yes"… For my Lenovo S12, I had to manually restart Ubuntu - and still with the very long restart…/no start/cold boot/reboot/pressing the shift key required Open mythTV (unity dash, top of icon totem, open, and make sure the ruler&pen icon on the bottom is selected, 2nd from left) type in "mythTV". Might be a good idea to drag and drop the mythTV icon to the terminal, it's easy to get rid of later. Will open with Select country & language. Do so. then get message with "No", hit "Ok" and arrive at the data base Configuration 1/2 screen. You will need your brackend password, from backend ? Setup General Database Configuration 1/2 Password:~? Enter this Hit Alt-n to go to the next page. Select "Use custom id…", then enter a custom ID, I use the machine's name. Hit finish, and MythTV should start up with all default settings. For the lenovo S12, the first thing you want to do is to set Playback profiles to "Normal". From Setup TV Settings Playback Alt-N(ext) Alt-N(ext) Playback Profiles (3/8) : Change Current Video Playback Profile to "Normal". You can fiddle with this setting later. For the lenovo S12, the second thing is to get the sound going. From Setup General Alt-N(ext) Alt-N(ext) Alt-N(ext) Audio System: The top of the screen is a button title "Scan for audio devices", move the highlight there and press the Space bar. Then Tab down to Audio Output Device: and left-right arrow until "ALSA:hw:Card=Intel,DEV=0" is selected. Then Alt-N(ext) until "Finish". Now you should have sound. You should now have MythTV working nicely on the Lenovo S12 Notes about wireless: Running Lenovo S12 on wireless is demanding on both power and WiFi connection. Best results will be obtained when running on power and wired connection. I run my S12 on wireless, actually two serial connections with two access points, something that is not easy to achieve. Here Mythbuntu client-server (in den) <? wireless link 1 <?office LAN? wireless link 2 <? Lenovo S12 Ubuntu 11.10 The office LAN is fixed IP behind an Untangle firewall router. There is another MythTV client on Ubuntu 10.10 computer in the office (which has always worked well). ProblemMythbuntu\Win7 client hangs with frozen frames, short segment of audio repeating. Hardware Rosewill RNX-G300EX IEEE 802.11b/g PCI Wireless Card on client-server 2 Linksys WRT54GL wireless broadband routers on LAN for link1 and link 2 WRT54GL FirmwareDD-WRT v24-sp2(07/22/09) voip set up to act as an access point. Note? many people advised this was an unworkable scheme, and in probably most cases it will be. Solution? Set up DD-WRT with the following Wireless settings… Basic Channel: Different fixed channels at least 4 difference, I use 6 & 11 Basic Sensitivity Range (ACK timing): 50 MAC filter use filter: Enable, Selected Permit only clients listed to access… Requires adding MAC addresses in "Edit MAC Filter List" This causes the 54GL's to ignore any but the listed MAC address, down side, no "guest" capability. Advanced Basic rate: All Advanced CTS Protection Mode: Off Advanced Frame Burst: Enable Advanced Max associate clients: 4 for client link 2, 1 for client-server link 1 Advanced AP isolation: Enable Advanced Preamble: Short Advanced Afterburner: On Advanced Wireless GUI access: Off Advanced WMM support: Off Other settings: default for supplied firmware. Why I suspect this worked? The 54GL Access Points's with the firmware's setting are set to handle a multiple client, wide area situation. With these mods I reconfigured them for a small area, few client situation, disabling Advanced WMM probably the most important. In addition, the client mythtv when used all other users of its access point are turned off except for a Skype phone. Also, the client-server is set up to allow other connections though it's LAN connection, and these are used to connect the TV and disc players, not used when client is being used.

  Read the article

• Openvpn plugin openvpn-auth-ldap does not bind to Active Directory

  - by Selivanov Pavel

  I'm trying to configure OpenVPN with openvpn-auth-ldap plugin to authorize users via Active Directory LDAP. When I use the same server config without plugin option, and add client config with generated client key and cert, connection is successful, so problem is in the plugin. server.conf: plugin /usr/lib/openvpn/openvpn-auth-ldap.so "/etc/openvpn-test/openvpn-auth-ldap.conf" port 1194 proto tcp dev tun keepalive 10 60 topology subnet server 10.0.2.0 255.255.255.0 tls-server ca ca.crt dh dh1024.pem cert server.crt key server.key #crl-verify crl.pem persist-key persist-tun user nobody group nogroup verb 3 mute 20 openvpn-auth-ldap.conf: <LDAP> URL ldap://dc1.domain:389 TLSEnable no BindDN cn=bot_auth,cn=Users,dc=domain Password bot_auth Timeout 15 FollowReferrals yes </LDAP> <Authorization> BaseDN "cn=Users,dc=domain" SearchFilter "(sAMAccountName=%u)" RequireGroup false # <Group> # BaseDN "ou=groups,dc=mycompany,dc=local" # SearchFilter "(|(cn=developers)(cn=artists))" # MemberAttribute uniqueMember # </Group> </Authorization> Top-level domain in AD is used by historical reasons. Analogue configuration is working for Apache 2.2 in mod-authzn-ldap. User and password are correct. client.conf: remote server_name port 1194 proto tcp client pull remote-cert-tls server dev tun resolv-retry infinite nobind ca ca.crt ; with keys - works fine #cert test.crt #key test.key ; without keys - by password auth-user-pass persist-tun verb 3 mute 20 In server log there is string PLUGIN_INIT: POST /usr/lib/openvpn/openvpn-auth-ldap.so '[/usr/lib/openvpn/openvpn-auth-ldap.so] [/etc/openvpn-test/openvpn-auth-ldap.conf]' which indicates, that plugin failed. I can telnet to dc1.domain:389, so this is not network/firewall problem. Later server says TLS Error: TLS object -> incoming plaintext read error TLS handshake failed - without plugin it tryes to do usal key authentification. server log: Tue Nov 22 03:06:20 2011 OpenVPN 2.1.3 i486-pc-linux-gnu [SSL] [LZO2] [EPOLL] [PKCS11] [MH] [PF_INET6] [eurephia] built on Oct 21 2010 Tue Nov 22 03:06:20 2011 NOTE: OpenVPN 2.1 requires '--script-security 2' or higher to call user-defined scripts or executables Tue Nov 22 03:06:20 2011 PLUGIN_INIT: POST /usr/lib/openvpn/openvpn-auth-ldap.so '[/usr/lib/openvpn/openvpn-auth-ldap.so] [/etc/openvpn-test/openvpn-auth-ldap.conf]' intercepted=PLUGIN_AUTH_USER_PASS_VERIFY|PLUGIN_CLIENT_CONNECT|PLUGIN_CLIENT_DISCONNECT Tue Nov 22 03:06:20 2011 Diffie-Hellman initialized with 1024 bit key Tue Nov 22 03:06:20 2011 /usr/bin/openssl-vulnkey -q -b 1024 -m <modulus omitted> Tue Nov 22 03:06:20 2011 Control Channel Authentication: using 'ta.key' as a OpenVPN static key file Tue Nov 22 03:06:20 2011 Outgoing Control Channel Authentication: Using 160 bit message hash 'SHA1' for HMAC authentication Tue Nov 22 03:06:20 2011 Incoming Control Channel Authentication: Using 160 bit message hash 'SHA1' for HMAC authentication Tue Nov 22 03:06:20 2011 TLS-Auth MTU parms [ L:1543 D:168 EF:68 EB:0 ET:0 EL:0 ] Tue Nov 22 03:06:20 2011 Socket Buffers: R=[87380->131072] S=[16384->131072] Tue Nov 22 03:06:20 2011 TUN/TAP device tun1 opened Tue Nov 22 03:06:20 2011 TUN/TAP TX queue length set to 100 Tue Nov 22 03:06:20 2011 /sbin/ifconfig tun1 10.0.2.1 netmask 255.255.255.0 mtu 1500 broadcast 10.0.2.255 Tue Nov 22 03:06:20 2011 Data Channel MTU parms [ L:1543 D:1450 EF:43 EB:4 ET:0 EL:0 ] Tue Nov 22 03:06:20 2011 GID set to nogroup Tue Nov 22 03:06:20 2011 UID set to nobody Tue Nov 22 03:06:20 2011 Listening for incoming TCP connection on [undef] Tue Nov 22 03:06:20 2011 TCPv4_SERVER link local (bound): [undef] Tue Nov 22 03:06:20 2011 TCPv4_SERVER link remote: [undef] Tue Nov 22 03:06:20 2011 MULTI: multi_init called, r=256 v=256 Tue Nov 22 03:06:20 2011 IFCONFIG POOL: base=10.0.2.2 size=252 Tue Nov 22 03:06:20 2011 MULTI: TCP INIT maxclients=1024 maxevents=1028 Tue Nov 22 03:06:20 2011 Initialization Sequence Completed Tue Nov 22 03:07:10 2011 MULTI: multi_create_instance called Tue Nov 22 03:07:10 2011 Re-using SSL/TLS context Tue Nov 22 03:07:10 2011 Control Channel MTU parms [ L:1543 D:168 EF:68 EB:0 ET:0 EL:0 ] Tue Nov 22 03:07:10 2011 Data Channel MTU parms [ L:1543 D:1450 EF:43 EB:4 ET:0 EL:0 ] Tue Nov 22 03:07:10 2011 Local Options hash (VER=V4): 'c413e92e' Tue Nov 22 03:07:10 2011 Expected Remote Options hash (VER=V4): 'd8421bb0' Tue Nov 22 03:07:10 2011 TCP connection established with [AF_INET]10.0.0.9:47808 Tue Nov 22 03:07:10 2011 TCPv4_SERVER link local: [undef] Tue Nov 22 03:07:10 2011 TCPv4_SERVER link remote: [AF_INET]10.0.0.9:47808 Tue Nov 22 03:07:11 2011 10.0.0.9:47808 TLS: Initial packet from [AF_INET]10.0.0.9:47808, sid=a2cd4052 84b47108 Tue Nov 22 03:07:11 2011 10.0.0.9:47808 TLS_ERROR: BIO read tls_read_plaintext error: error:140890C7:SSL routines:SSL3_GET_CLIENT_CERTIFICATE:peer did not return a certificate Tue Nov 22 03:07:11 2011 10.0.0.9:47808 TLS Error: TLS object -> incoming plaintext read error Tue Nov 22 03:07:11 2011 10.0.0.9:47808 TLS Error: TLS handshake failed Tue Nov 22 03:07:11 2011 10.0.0.9:47808 Fatal TLS error (check_tls_errors_co), restarting Tue Nov 22 03:07:11 2011 10.0.0.9:47808 SIGUSR1[soft,tls-error] received, client-instance restarting Tue Nov 22 03:07:11 2011 TCP/UDP: Closing socket client log: Tue Nov 22 03:06:18 2011 OpenVPN 2.1.3 x86_64-pc-linux-gnu [SSL] [LZO2] [EPOLL] [PKCS11] [MH] [PF_INET6] [eurephia] built on Oct 22 2010 Enter Auth Username:user Enter Auth Password: Tue Nov 22 03:06:25 2011 NOTE: OpenVPN 2.1 requires '--script-security 2' or higher to call user-defined scripts or executables Tue Nov 22 03:06:25 2011 Control Channel Authentication: using 'ta.key' as a OpenVPN static key file Tue Nov 22 03:06:25 2011 Outgoing Control Channel Authentication: Using 160 bit message hash 'SHA1' for HMAC authentication Tue Nov 22 03:06:25 2011 Incoming Control Channel Authentication: Using 160 bit message hash 'SHA1' for HMAC authentication Tue Nov 22 03:06:25 2011 Control Channel MTU parms [ L:1543 D:168 EF:68 EB:0 ET:0 EL:0 ] Tue Nov 22 03:06:25 2011 Socket Buffers: R=[87380->131072] S=[16384->131072] Tue Nov 22 03:06:25 2011 Data Channel MTU parms [ L:1543 D:1450 EF:43 EB:4 ET:0 EL:0 ] Tue Nov 22 03:06:25 2011 Local Options hash (VER=V4): 'd8421bb0' Tue Nov 22 03:06:25 2011 Expected Remote Options hash (VER=V4): 'c413e92e' Tue Nov 22 03:06:25 2011 Attempting to establish TCP connection with [AF_INET]10.0.0.2:1194 [nonblock] Tue Nov 22 03:06:26 2011 TCP connection established with [AF_INET]10.0.0.2:1194 Tue Nov 22 03:06:26 2011 TCPv4_CLIENT link local: [undef] Tue Nov 22 03:06:26 2011 TCPv4_CLIENT link remote: [AF_INET]10.0.0.2:1194 Tue Nov 22 03:06:26 2011 TLS: Initial packet from [AF_INET]10.0.0.2:1194, sid=7a3c2a0f bd35bca7 Tue Nov 22 03:06:26 2011 WARNING: this configuration may cache passwords in memory -- use the auth-nocache option to prevent this Tue Nov 22 03:06:26 2011 VERIFY OK: depth=1, /C=US/ST=CA/L=SanFrancisco/O=Fort-Funston/CN=Fort-Funston_CA/[email protected] Tue Nov 22 03:06:26 2011 Validating certificate key usage Tue Nov 22 03:06:26 2011 ++ Certificate has key usage 00a0, expects 00a0 Tue Nov 22 03:06:26 2011 VERIFY KU OK Tue Nov 22 03:06:26 2011 Validating certificate extended key usage Tue Nov 22 03:06:26 2011 ++ Certificate has EKU (str) TLS Web Server Authentication, expects TLS Web Server Authentication Tue Nov 22 03:06:26 2011 VERIFY EKU OK Tue Nov 22 03:06:26 2011 VERIFY OK: depth=0, /C=US/ST=CA/L=SanFrancisco/O=Fort-Funston/CN=server/[email protected] Tue Nov 22 03:06:26 2011 Connection reset, restarting [0] Tue Nov 22 03:06:26 2011 TCP/UDP: Closing socket Tue Nov 22 03:06:26 2011 SIGUSR1[soft,connection-reset] received, process restarting Tue Nov 22 03:06:26 2011 Restart pause, 5 second(s) ^CTue Nov 22 03:06:27 2011 SIGINT[hard,init_instance] received, process exiting Does anybody know how to get openvpn-auth-ldap wirking?

  Read the article

• openvpn: after changing to server mode, client does not create TUN device

  - by lurscher

  i had a previously working configuration with the config files used in a previous question However, i've changed this now to the following configuration using server mode, everything on the logs seem fine, however the client doesn't create any tun interface, so i don't have anything to connect to, presumably, i need to add or push some route commands, but i don't have any idea at this point what i need to do. I am posting all my relevant configuration files server.conf: dev tun server 10.8.117.0 255.255.255.0 ifconfig-pool-persist ipp.txt tls-server dh /home/lurscher/keys/dh1024.pem ca /home/lurscher/keys/ca.crt cert /home/lurscher/keys/vpnCh8TestServer.crt key /home/lurscher/keys/vpnCh8TestServer.key status openvpn-status.log log openvpn.log comp-lzo verb 3 and client.conf: dev tun remote my.server.com tls-client ca /home/chuckq/keys/ca.crt cert /home/chuckq/keys/vpnCh8TestClient.crt key /home/chuckq/keys/vpnCh8TestClient.key ns-cert-type server ; port 1194 ; user nobody ; group nogroup status openvpn-status.log log openvpn.log comp-lzo verb 3 the server ifconfig shows a tun device: tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.8.117.1 P-t-P:10.8.117.2 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) However the client ifconfig does not show any tun interface! $ ifconfig tun0 tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 POINTOPOINT NOARP MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) the client log says: Tue May 17 23:27:09 2011 OpenVPN 2.1.0 i686-pc-linux-gnu [SSL] [LZO2] [EPOLL] [PKCS11] [MH] [PF_INET6] [eurephia] built on Jul 12 2010 Tue May 17 23:27:09 2011 IMPORTANT: OpenVPN's default port number is now 1194, based on an official port number assignment by IANA. OpenVPN 2.0-beta16 and earlier used 5000 as the default port. Tue May 17 23:27:09 2011 NOTE: the current --script-security setting may allow this configuration to call user-defined scripts Tue May 17 23:27:09 2011 /usr/bin/openssl-vulnkey -q -b 1024 -m <modulus omitted> Tue May 17 23:27:09 2011 LZO compression initialized Tue May 17 23:27:09 2011 Control Channel MTU parms [ L:1542 D:138 EF:38 EB:0 ET:0 EL:0 ] Tue May 17 23:27:09 2011 TUN/TAP device tun0 opened Tue May 17 23:27:09 2011 TUN/TAP TX queue length set to 100 Tue May 17 23:27:09 2011 Data Channel MTU parms [ L:1542 D:1450 EF:42 EB:135 ET:0 EL:0 AF:3/1 ] Tue May 17 23:27:09 2011 Local Options hash (VER=V4): '41690919' Tue May 17 23:27:09 2011 Expected Remote Options hash (VER=V4): '530fdded' Tue May 17 23:27:09 2011 Socket Buffers: R=[114688->131072] S=[114688->131072] Tue May 17 23:27:09 2011 UDPv4 link local (bound): [undef] Tue May 17 23:27:09 2011 UDPv4 link remote: [AF_INET]192.168.0.101:1194 Tue May 17 23:27:09 2011 TLS: Initial packet from [AF_INET]192.168.0.101:1194, sid=8e8bdc33 f4275407 Tue May 17 23:27:09 2011 VERIFY OK: depth=1, /C=CA/ST=Out/L=There/O=Ubuntu/OU=Home/CN=Ubuntu_CA/name=lurscher/[email protected] Tue May 17 23:27:09 2011 VERIFY OK: nsCertType=SERVER Tue May 17 23:27:09 2011 VERIFY OK: depth=0, /C=CA/ST=Out/L=There/O=Ubuntu/OU=Home/CN=vpnCh8TestServer/name=lurscher/[email protected] Tue May 17 23:27:09 2011 Data Channel Encrypt: Cipher 'BF-CBC' initialized with 128 bit key Tue May 17 23:27:09 2011 Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Tue May 17 23:27:09 2011 Data Channel Decrypt: Cipher 'BF-CBC' initialized with 128 bit key Tue May 17 23:27:09 2011 Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Tue May 17 23:27:09 2011 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 1024 bit RSA Tue May 17 23:27:09 2011 [vpnCh8TestServer] Peer Connection Initiated with [AF_INET]192.168.0.101:1194 Tue May 17 23:27:10 2011 Initialization Sequence Completed the client status log: OpenVPN STATISTICS Updated,Tue May 17 23:30:09 2011 TUN/TAP read bytes,0 TUN/TAP write bytes,0 TCP/UDP read bytes,5604 TCP/UDP write bytes,4244 Auth read bytes,0 pre-compress bytes,0 post-compress bytes,0 pre-decompress bytes,0 post-decompress bytes,0 END and the server log says: Tue May 17 23:18:25 2011 OpenVPN 2.1.0 x86_64-pc-linux-gnu [SSL] [LZO2] [EPOLL] [PKCS11] [MH] [PF_INET6] [eurephia] built on Jul 12 2010 Tue May 17 23:18:25 2011 IMPORTANT: OpenVPN's default port number is now 1194, based on an official port number assignment by IANA. OpenVPN 2.0-beta16 and earlier used 5000 as the default port. Tue May 17 23:18:25 2011 WARNING: --keepalive option is missing from server config Tue May 17 23:18:25 2011 NOTE: your local LAN uses the extremely common subnet address 192.168.0.x or 192.168.1.x. Be aware that this might create routing conflicts if you connect to the VPN server from public locations such as internet cafes that use the same subnet. Tue May 17 23:18:25 2011 NOTE: the current --script-security setting may allow this configuration to call user-defined scripts Tue May 17 23:18:25 2011 Diffie-Hellman initialized with 1024 bit key Tue May 17 23:18:25 2011 /usr/bin/openssl-vulnkey -q -b 1024 -m <modulus omitted> Tue May 17 23:18:25 2011 TLS-Auth MTU parms [ L:1542 D:138 EF:38 EB:0 ET:0 EL:0 ] Tue May 17 23:18:25 2011 ROUTE default_gateway=192.168.0.1 Tue May 17 23:18:25 2011 TUN/TAP device tun0 opened Tue May 17 23:18:25 2011 TUN/TAP TX queue length set to 100 Tue May 17 23:18:25 2011 /sbin/ifconfig tun0 10.8.117.1 pointopoint 10.8.117.2 mtu 1500 Tue May 17 23:18:25 2011 /sbin/route add -net 10.8.117.0 netmask 255.255.255.0 gw 10.8.117.2 Tue May 17 23:18:25 2011 Data Channel MTU parms [ L:1542 D:1450 EF:42 EB:135 ET:0 EL:0 AF:3/1 ] Tue May 17 23:18:25 2011 Socket Buffers: R=[126976->131072] S=[126976->131072] Tue May 17 23:18:25 2011 UDPv4 link local (bound): [undef] Tue May 17 23:18:25 2011 UDPv4 link remote: [undef] Tue May 17 23:18:25 2011 MULTI: multi_init called, r=256 v=256 Tue May 17 23:18:25 2011 IFCONFIG POOL: base=10.8.117.4 size=62 Tue May 17 23:18:25 2011 IFCONFIG POOL LIST Tue May 17 23:18:25 2011 vpnCh8TestClient,10.8.117.4 Tue May 17 23:18:25 2011 Initialization Sequence Completed Tue May 17 23:27:22 2011 MULTI: multi_create_instance called Tue May 17 23:27:22 2011 192.168.0.104:1194 Re-using SSL/TLS context Tue May 17 23:27:22 2011 192.168.0.104:1194 LZO compression initialized Tue May 17 23:27:22 2011 192.168.0.104:1194 Control Channel MTU parms [ L:1542 D:138 EF:38 EB:0 ET:0 EL:0 ] Tue May 17 23:27:22 2011 192.168.0.104:1194 Data Channel MTU parms [ L:1542 D:1450 EF:42 EB:135 ET:0 EL:0 AF:3/1 ] Tue May 17 23:27:22 2011 192.168.0.104:1194 Local Options hash (VER=V4): '530fdded' Tue May 17 23:27:22 2011 192.168.0.104:1194 Expected Remote Options hash (VER=V4): '41690919' Tue May 17 23:27:22 2011 192.168.0.104:1194 TLS: Initial packet from [AF_INET]192.168.0.104:1194, sid=8972b565 79323f68 Tue May 17 23:27:22 2011 192.168.0.104:1194 VERIFY OK: depth=1, /C=CA/ST=Out/L=There/O=Ubuntu/OU=Home/CN=Ubuntu_CA/name=lurscher/[email protected] Tue May 17 23:27:22 2011 192.168.0.104:1194 VERIFY OK: depth=0, /C=CA/ST=Out/L=There/O=Ubuntu/OU=Home/CN=Ubuntu_CA/name=lurscher/[email protected] Tue May 17 23:27:22 2011 192.168.0.104:1194 Data Channel Encrypt: Cipher 'BF-CBC' initialized with 128 bit key Tue May 17 23:27:22 2011 192.168.0.104:1194 Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Tue May 17 23:27:22 2011 192.168.0.104:1194 Data Channel Decrypt: Cipher 'BF-CBC' initialized with 128 bit key Tue May 17 23:27:22 2011 192.168.0.104:1194 Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Tue May 17 23:27:22 2011 192.168.0.104:1194 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 1024 bit RSA Tue May 17 23:27:22 2011 192.168.0.104:1194 [vpnCh8TestClient] Peer Connection Initiated with [AF_INET]192.168.0.104:1194 Tue May 17 23:27:22 2011 vpnCh8TestClient/192.168.0.104:1194 MULTI: Learn: 10.8.117.6 -> vpnCh8TestClient/192.168.0.104:1194 Tue May 17 23:27:22 2011 vpnCh8TestClient/192.168.0.104:1194 MULTI: primary virtual IP for vpnCh8TestClient/192.168.0.104:1194: 10.8.117.6 finally, the server status log: OpenVPN CLIENT LIST Updated,Tue May 17 23:36:25 2011 Common Name,Real Address,Bytes Received,Bytes Sent,Connected Since vpnCh8TestClient,192.168.0.104:1194,4244,5604,Tue May 17 23:27:22 2011 ROUTING TABLE Virtual Address,Common Name,Real Address,Last Ref 10.8.117.6,vpnCh8TestClient,192.168.0.104:1194,Tue May 17 23:27:22 2011 GLOBAL STATS Max bcast/mcast queue length,0 END

  Read the article

• Outbound traffic being blocked for MIP/VIPped servers (Juniper SSG5)

  - by Mark S. Rasmussen

  As we've been having some problems with sporadic packet loss, I've been preparing a replacement router (also an SSG5) for our current Juniper SSG5. I've setup the new SSG5 identically to the old one. We have a /29 IP range with a single IP setup as a MIP map to a server and two others being used for VIP maps. Each VIP/MIP is accompanied by relevant policies. Long story short - we tried connected the new SSG5 and some things were not working as they should. No problem, I just reconnected the old one. However, some things are still broken, even when I reconnected the old one. I fear I may have inadvertently changed some settings while browsing through old settings in my attempt to reconfigure the new SSG5 unit. All inbound traffic seems to work as expected. However, the 192.168.2.202 server can't initiate any outbound connections. It works perfectly on the local network, but any pings or DNS lookups to external IP's fail. The MIP & VIP map to it works perfectly - I can access it through HTTP and RDP without issues. Any tips on what to debug, or where I've messed up my config? I've attached the full config here (with anonymized IPs): set clock timezone 1 set vrouter trust-vr sharable set vrouter "untrust-vr" exit set vrouter "trust-vr" unset auto-route-export exit set service "MyVOIP_UDP4569" protocol udp src-port 0-65535 dst-port 4569-4569 set service "MyVOIP_TCP22" protocol tcp src-port 0-65535 dst-port 22-22 set service "MyRDP" protocol tcp src-port 0-65535 dst-port 3389-3389 set service "MyRsync" protocol tcp src-port 0-65535 dst-port 873-873 set service "NZ_FTP" protocol tcp src-port 0-65535 dst-port 40000-41000 set service "NZ_FTP" + tcp src-port 0-65535 dst-port 21-21 set service "PPTP-VPN" protocol 47 src-port 2048-2048 dst-port 2048-2048 set service "PPTP-VPN" + tcp src-port 1024-65535 dst-port 1723-1723 set service "NZ_FMS_1935" protocol tcp src-port 0-65535 dst-port 1935-1935 set service "NZ_FMS_1935" + udp src-port 0-65535 dst-port 1935-1935 set service "NZ_FMS_8080" protocol tcp src-port 0-65535 dst-port 8080-8080 set service "CrashPlan Server" protocol tcp src-port 0-65535 dst-port 4280-4280 set service "CrashPlan Console" protocol tcp src-port 0-65535 dst-port 4282-4282 unset alg sip enable set auth-server "Local" id 0 set auth-server "Local" server-name "Local" set auth default auth server "Local" set auth radius accounting port 1646 set admin auth timeout 10 set admin auth server "Local" set admin format dos set vip multi-port set zone "Trust" vrouter "trust-vr" set zone "Untrust" vrouter "trust-vr" set zone "DMZ" vrouter "trust-vr" set zone "VLAN" vrouter "trust-vr" set zone "Untrust-Tun" vrouter "trust-vr" set zone "Trust" tcp-rst set zone "Untrust" block unset zone "Untrust" tcp-rst set zone "DMZ" tcp-rst set zone "VLAN" block unset zone "VLAN" tcp-rst set zone "Untrust" screen tear-drop set zone "Untrust" screen syn-flood set zone "Untrust" screen ping-death set zone "Untrust" screen ip-filter-src set zone "Untrust" screen land set zone "V1-Untrust" screen tear-drop set zone "V1-Untrust" screen syn-flood set zone "V1-Untrust" screen ping-death set zone "V1-Untrust" screen ip-filter-src set zone "V1-Untrust" screen land set interface ethernet0/0 phy full 100mb set interface ethernet0/3 phy full 100mb set interface ethernet0/4 phy full 100mb set interface ethernet0/5 phy full 100mb set interface ethernet0/6 phy full 100mb set interface "ethernet0/0" zone "Untrust" set interface "ethernet0/1" zone "Null" set interface "bgroup0" zone "Trust" set interface "bgroup1" zone "Trust" set interface "bgroup2" zone "Trust" set interface bgroup2 port ethernet0/2 set interface bgroup0 port ethernet0/3 set interface bgroup0 port ethernet0/4 set interface bgroup1 port ethernet0/5 set interface bgroup1 port ethernet0/6 unset interface vlan1 ip set interface ethernet0/0 ip 212.242.193.18/29 set interface ethernet0/0 route set interface bgroup0 ip 192.168.1.1/24 set interface bgroup0 nat set interface bgroup1 ip 192.168.2.1/24 set interface bgroup1 nat set interface bgroup2 ip 192.168.3.1/24 set interface bgroup2 nat set interface ethernet0/0 gateway 212.242.193.17 unset interface vlan1 bypass-others-ipsec unset interface vlan1 bypass-non-ip set interface ethernet0/0 ip manageable set interface bgroup0 ip manageable set interface bgroup1 ip manageable set interface bgroup2 ip manageable set interface bgroup0 manage mtrace unset interface bgroup1 manage ssh unset interface bgroup1 manage telnet unset interface bgroup1 manage snmp unset interface bgroup1 manage ssl unset interface bgroup1 manage web unset interface bgroup2 manage ssh unset interface bgroup2 manage telnet unset interface bgroup2 manage snmp unset interface bgroup2 manage ssl unset interface bgroup2 manage web set interface ethernet0/0 vip 212.242.193.19 2048 "PPTP-VPN" 192.168.1.131 set interface ethernet0/0 vip 212.242.193.19 + 4280 "CrashPlan Server" 192.168.1.131 set interface ethernet0/0 vip 212.242.193.19 + 4282 "CrashPlan Console" 192.168.1.131 set interface ethernet0/0 vip 212.242.193.22 22 "MyVOIP_TCP22" 192.168.2.127 set interface ethernet0/0 vip 212.242.193.22 + 4569 "MyVOIP_UDP4569" 192.168.2.127 set interface ethernet0/0 vip 212.242.193.22 + 3389 "MyRDP" 192.168.2.202 set interface ethernet0/0 vip 212.242.193.22 + 873 "MyRsync" 192.168.2.201 set interface ethernet0/0 vip 212.242.193.22 + 80 "HTTP" 192.168.2.202 set interface ethernet0/0 vip 212.242.193.22 + 2048 "PPTP-VPN" 192.168.2.201 set interface ethernet0/0 vip 212.242.193.22 + 8080 "NZ_FMS_8080" 192.168.2.216 set interface ethernet0/0 vip 212.242.193.22 + 1935 "NZ_FMS_1935" 192.168.2.216 set interface bgroup0 dhcp server service set interface bgroup1 dhcp server service set interface bgroup2 dhcp server service set interface bgroup0 dhcp server auto set interface bgroup1 dhcp server auto set interface bgroup2 dhcp server auto set interface bgroup0 dhcp server option domainname iplan set interface bgroup0 dhcp server option dns1 192.168.1.131 set interface bgroup1 dhcp server option domainname nzlan set interface bgroup1 dhcp server option dns1 192.168.2.202 set interface bgroup2 dhcp server option dns1 8.8.8.8 set interface bgroup2 dhcp server option wins1 8.8.4.4 set interface bgroup0 dhcp server ip 192.168.1.2 to 192.168.1.116 set interface bgroup1 dhcp server ip 192.168.2.2 to 192.168.2.116 set interface bgroup2 dhcp server ip 192.168.3.2 to 192.168.3.126 unset interface bgroup0 dhcp server config next-server-ip unset interface bgroup1 dhcp server config next-server-ip unset interface bgroup2 dhcp server config next-server-ip set interface "ethernet0/0" mip 212.242.193.21 host 192.168.2.202 netmask 255.255.255.255 vr "trust-vr" set interface "serial0/0" modem settings "USR" init "AT&F" set interface "serial0/0" modem settings "USR" active set interface "serial0/0" modem speed 115200 set interface "serial0/0" modem retry 3 set interface "serial0/0" modem interval 10 set interface "serial0/0" modem idle-time 10 set pak-poll p1queue pak-threshold 96 set pak-poll p2queue pak-threshold 32 set flow tcp-mss unset flow tcp-syn-check set dns host dns1 0.0.0.0 set dns host dns2 0.0.0.0 set dns host dns3 0.0.0.0 set address "Trust" "192.168.1.0/24" 192.168.1.0 255.255.255.0 set address "Trust" "192.168.2.0/24" 192.168.2.0 255.255.255.0 set address "Trust" "192.168.3.0/24" 192.168.3.0 255.255.255.0 set ike respond-bad-spi 1 unset ike ikeid-enumeration unset ike dos-protection unset ipsec access-session enable set ipsec access-session maximum 5000 set ipsec access-session upper-threshold 0 set ipsec access-session lower-threshold 0 set ipsec access-session dead-p2-sa-timeout 0 unset ipsec access-session log-error unset ipsec access-session info-exch-connected unset ipsec access-session use-error-log set l2tp default ppp-auth chap set url protocol websense exit set policy id 1 from "Trust" to "Untrust" "Any" "Any" "ANY" permit traffic set policy id 1 exit set policy id 2 from "Untrust" to "Trust" "Any" "VIP(212.242.193.19)" "PPTP-VPN" permit traffic set policy id 2 exit set policy id 3 from "Untrust" to "Trust" "Any" "VIP(212.242.193.22)" "HTTP" permit traffic priority 0 set policy id 3 set service "MyRDP" set service "MyRsync" set service "MyVOIP_TCP22" set service "MyVOIP_UDP4569" exit set policy id 6 from "Trust" to "Trust" "192.168.1.0/24" "192.168.2.0/24" "ANY" deny set policy id 6 exit set policy id 7 from "Trust" to "Trust" "192.168.2.0/24" "192.168.1.0/24" "ANY" deny set policy id 7 exit set policy id 8 from "Trust" to "Trust" "192.168.3.0/24" "192.168.1.0/24" "ANY" deny set policy id 8 exit set policy id 9 from "Trust" to "Trust" "192.168.3.0/24" "192.168.2.0/24" "ANY" deny set policy id 9 exit set policy id 10 from "Untrust" to "Trust" "Any" "MIP(212.242.193.21)" "NZ_FTP" permit set policy id 10 exit set policy id 11 from "Untrust" to "Trust" "Any" "VIP(212.242.193.22)" "PPTP-VPN" permit set policy id 11 exit set policy id 12 from "Untrust" to "Trust" "Any" "VIP(212.242.193.22)" "NZ_FMS_1935" permit set policy id 12 set service "NZ_FMS_8080" exit set policy id 13 from "Untrust" to "Trust" "Any" "VIP(212.242.193.19)" "CrashPlan Console" permit set policy id 13 set service "CrashPlan Server" exit set nsmgmt bulkcli reboot-timeout 60 set ssh version v2 set config lock timeout 5 set snmp port listen 161 set snmp port trap 162 set vrouter "untrust-vr" exit set vrouter "trust-vr" unset add-default-route exit set vrouter "untrust-vr" exit set vrouter "trust-vr" exit

  Read the article

• Allowing connections initiated from outside

  - by Mark S. Rasmussen

  I've got an old Juniper SSG5 running ScreenOS 5.4.0r6.0. Once a day, more or less, it'll start randomly dropping packets at a rate of ~5-10%. We currently solve this issue by simply rebooting the unit, after which it resumes working in perfect condition. As this error has started appearing randomly, without any configuration or hardware changes, I'm assuming I've got an aging unit about to fail. As such, I've got a replacement SSG5 running ScreenOS 6.0. I've dumped the config on the 5.4 and imported it into a clean 6.0, and it seems to gladly accept it, and all my configuration seems to be A-OK. However, upon connecting the new unit, all outside-initiated connections seem to be blocked. If I browse our external IP from the inside, everything works perfectly, and it's not just port 80, SSH, Crashplan - all of our policies route correctly. All normal networking, initiated from the inside, work perfectly as well. If on the other hand I browse our external IP from the outside, everything is blocked. Barring differences between ScreenOS 5.4 and 6.0, the config is identical. Is there a setting somewhere that defines whether outside/inside initiated connections are allowed? unset key protection enable set clock timezone 1 set vrouter trust-vr sharable set vrouter "untrust-vr" exit set vrouter "trust-vr" unset auto-route-export exit set service "MyVOIP_UDP4569" protocol udp src-port 0-65535 dst-port 4569-4569 set service "MyVOIP_TCP22" protocol tcp src-port 0-65535 dst-port 22-22 set service "MyRDP" protocol tcp src-port 0-65535 dst-port 3389-3389 set service "MyRsync" protocol tcp src-port 0-65535 dst-port 873-873 set service "NZ_FTP" protocol tcp src-port 0-65535 dst-port 40000-41000 set service "NZ_FTP" + tcp src-port 0-65535 dst-port 21-21 set service "PPTP-VPN" protocol 47 src-port 2048-2048 dst-port 2048-2048 set service "PPTP-VPN" + tcp src-port 1024-65535 dst-port 1723-1723 set service "NZ_FMS_1935" protocol tcp src-port 0-65535 dst-port 1935-1935 set service "NZ_FMS_1935" + udp src-port 0-65535 dst-port 1935-1935 set service "NZ_FMS_8080" protocol tcp src-port 0-65535 dst-port 8080-8080 set service "CrashPlan Server" protocol tcp src-port 0-65535 dst-port 4280-4280 set service "CrashPlan Console" protocol tcp src-port 0-65535 dst-port 4282-4282 unset alg sip enable set alg appleichat enable unset alg appleichat re-assembly enable set alg sctp enable set auth-server "Local" id 0 set auth-server "Local" server-name "Local" set auth default auth server "Local" set auth radius accounting port 1646 set admin name "netscreen" set admin password "XXX" set admin auth web timeout 10 set admin auth dial-in timeout 3 set admin auth server "Local" set admin format dos set vip multi-port set zone "Trust" vrouter "trust-vr" set zone "Untrust" vrouter "trust-vr" set zone "DMZ" vrouter "trust-vr" set zone "VLAN" vrouter "trust-vr" set zone "Untrust-Tun" vrouter "trust-vr" set zone "Trust" tcp-rst set zone "Untrust" block unset zone "Untrust" tcp-rst set zone "MGT" block unset zone "V1-Trust" tcp-rst unset zone "V1-Untrust" tcp-rst set zone "DMZ" tcp-rst unset zone "V1-DMZ" tcp-rst unset zone "VLAN" tcp-rst set zone "Untrust" screen tear-drop set zone "Untrust" screen syn-flood set zone "Untrust" screen ping-death set zone "Untrust" screen ip-filter-src set zone "Untrust" screen land set zone "V1-Untrust" screen tear-drop set zone "V1-Untrust" screen syn-flood set zone "V1-Untrust" screen ping-death set zone "V1-Untrust" screen ip-filter-src set zone "V1-Untrust" screen land set interface ethernet0/0 phy full 100mb set interface ethernet0/3 phy full 100mb set interface ethernet0/4 phy full 100mb set interface ethernet0/5 phy full 100mb set interface ethernet0/6 phy full 100mb set interface "ethernet0/0" zone "Untrust" set interface "ethernet0/1" zone "Null" set interface "bgroup0" zone "Trust" set interface "bgroup1" zone "Trust" set interface "bgroup2" zone "Trust" set interface bgroup2 port ethernet0/2 set interface bgroup0 port ethernet0/3 set interface bgroup0 port ethernet0/4 set interface bgroup1 port ethernet0/5 set interface bgroup1 port ethernet0/6 unset interface vlan1 ip set interface ethernet0/0 ip 215.173.182.18/29 set interface ethernet0/0 route set interface bgroup0 ip 192.168.1.1/24 set interface bgroup0 nat set interface bgroup1 ip 192.168.2.1/24 set interface bgroup1 nat set interface bgroup2 ip 192.168.3.1/24 set interface bgroup2 nat set interface ethernet0/0 gateway 215.173.182.17 unset interface vlan1 bypass-others-ipsec unset interface vlan1 bypass-non-ip set interface ethernet0/0 ip manageable set interface bgroup0 ip manageable set interface bgroup1 ip manageable set interface bgroup2 ip manageable set interface bgroup0 manage mtrace unset interface bgroup1 manage ssh unset interface bgroup1 manage telnet unset interface bgroup1 manage snmp unset interface bgroup1 manage ssl unset interface bgroup1 manage web unset interface bgroup2 manage ssh unset interface bgroup2 manage telnet unset interface bgroup2 manage snmp unset interface bgroup2 manage ssl unset interface bgroup2 manage web set interface ethernet0/0 vip 215.173.182.19 2048 "PPTP-VPN" 192.168.1.131 set interface ethernet0/0 vip 215.173.182.19 + 4280 "CrashPlan Server" 192.168.1.131 set interface ethernet0/0 vip 215.173.182.19 + 4282 "CrashPlan Console" 192.168.1.131 set interface ethernet0/0 vip 215.173.182.22 22 "MyVOIP_TCP22" 192.168.2.127 set interface ethernet0/0 vip 215.173.182.22 + 4569 "MyVOIP_UDP4569" 192.168.2.127 set interface ethernet0/0 vip 215.173.182.22 + 3389 "MyRDP" 192.168.2.202 set interface ethernet0/0 vip 215.173.182.22 + 873 "MyRsync" 192.168.2.201 set interface ethernet0/0 vip 215.173.182.22 + 80 "HTTP" 192.168.2.202 set interface ethernet0/0 vip 215.173.182.22 + 2048 "PPTP-VPN" 192.168.2.201 set interface ethernet0/0 vip 215.173.182.22 + 8080 "NZ_FMS_8080" 192.168.2.216 set interface ethernet0/0 vip 215.173.182.22 + 1935 "NZ_FMS_1935" 192.168.2.216 set interface bgroup0 dhcp server service set interface bgroup1 dhcp server service set interface bgroup2 dhcp server service set interface bgroup0 dhcp server auto set interface bgroup1 dhcp server auto set interface bgroup2 dhcp server auto set interface bgroup0 dhcp server option domainname companyalan set interface bgroup0 dhcp server option dns1 192.168.1.131 set interface bgroup1 dhcp server option domainname companyblan set interface bgroup1 dhcp server option dns1 192.168.2.202 set interface bgroup2 dhcp server option dns1 8.8.8.8 set interface bgroup2 dhcp server option wins1 8.8.4.4 set interface bgroup0 dhcp server ip 192.168.1.2 to 192.168.1.116 set interface bgroup1 dhcp server ip 192.168.2.2 to 192.168.2.116 set interface bgroup2 dhcp server ip 192.168.3.2 to 192.168.3.126 unset interface bgroup0 dhcp server config next-server-ip unset interface bgroup1 dhcp server config next-server-ip unset interface bgroup2 dhcp server config next-server-ip set interface "ethernet0/0" mip 215.173.182.21 host 192.168.2.202 netmask 255.255.255.255 vr "trust-vr" set interface "serial0/0" modem settings "USR" init "AT&F" set interface "serial0/0" modem settings "USR" active set interface "serial0/0" modem speed 115200 set interface "serial0/0" modem retry 3 set interface "serial0/0" modem interval 10 set interface "serial0/0" modem idle-time 10 set flow tcp-mss unset flow tcp-syn-check unset flow tcp-syn-bit-check set flow reverse-route clear-text prefer set flow reverse-route tunnel always set pki authority default scep mode "auto" set pki x509 default cert-path partial set pki x509 dn name "[email protected]" set dns host dns1 0.0.0.0 set dns host dns2 0.0.0.0 set dns host dns3 0.0.0.0 set address "Trust" "192.168.1.0/24" 192.168.1.0 255.255.255.0 set address "Trust" "192.168.2.0/24" 192.168.2.0 255.255.255.0 set address "Trust" "192.168.3.0/24" 192.168.3.0 255.255.255.0 set crypto-policy exit set ike respond-bad-spi 1 set ike ikev2 ike-sa-soft-lifetime 60 unset ike ikeid-enumeration unset ike dos-protection unset ipsec access-session enable set ipsec access-session maximum 5000 set ipsec access-session upper-threshold 0 set ipsec access-session lower-threshold 0 set ipsec access-session dead-p2-sa-timeout 0 unset ipsec access-session log-error unset ipsec access-session info-exch-connected unset ipsec access-session use-error-log set vrouter "untrust-vr" exit set vrouter "trust-vr" exit set l2tp default ppp-auth chap set url protocol websense exit set policy id 1 from "Trust" to "Untrust" "Any" "Any" "ANY" permit set policy id 1 exit set policy id 2 from "Untrust" to "Trust" "Any" "VIP(215.173.182.19)" "PPTP-VPN" permit traffic set policy id 2 exit set policy id 3 from "Untrust" to "Trust" "Any" "VIP(215.173.182.22)" "HTTP" permit log set policy id 3 set service "MyRDP" set service "MyRsync" set service "MyVOIP_TCP22" set service "MyVOIP_UDP4569" exit set policy id 6 from "Trust" to "Trust" "192.168.1.0/24" "192.168.2.0/24" "ANY" deny set policy id 6 exit set policy id 7 from "Trust" to "Trust" "192.168.2.0/24" "192.168.1.0/24" "ANY" deny set policy id 7 exit set policy id 8 from "Trust" to "Trust" "192.168.3.0/24" "192.168.1.0/24" "ANY" deny set policy id 8 exit set policy id 9 from "Trust" to "Trust" "192.168.3.0/24" "192.168.2.0/24" "ANY" deny set policy id 9 exit set policy id 10 from "Untrust" to "Trust" "Any" "MIP(215.173.182.21)" "NZ_FTP" permit set policy id 10 exit set policy id 11 from "Untrust" to "Trust" "Any" "VIP(215.173.182.22)" "PPTP-VPN" permit set policy id 11 exit set policy id 12 from "Untrust" to "Trust" "Any" "VIP(215.173.182.22)" "NZ_FMS_1935" permit set policy id 12 set service "NZ_FMS_8080" exit set policy id 13 from "Untrust" to "Trust" "Any" "VIP(215.173.182.19)" "CrashPlan Console" permit set policy id 13 set service "CrashPlan Server" exit set nsmgmt bulkcli reboot-timeout 60 set ssh version v2 set config lock timeout 5 unset license-key auto-update set telnet client enable set snmp port listen 161 set snmp port trap 162 set vrouter "untrust-vr" exit set vrouter "trust-vr" unset add-default-route exit set vrouter "untrust-vr" exit set vrouter "trust-vr" exit Note that I've previously posted a similar question (pertaining to the same device & replacement, but ultimately caused by a malfunctioning switch, and thus clouding the current issue): Outbound traffic being blocked for MIP/VIPped servers (Juniper SSG5)

  Read the article

• Something very strange with network

  - by Rodnower

  Hello, I have Windows 7 and I have very strange thing with my network. Some time I was connected through wireless router and my IP was 192.168.2.103, router's IP was 192.168.2.1 and some other IP was 192.168.2.100. The last I get from page "active DHCP clients" of web interface of the router and from "wireless clients" I may to see that 192.168.2.100 not (!) belong to my MAC address. Router build by EDimax. So after that I disabled wireless function of the router and restarted it. In this time I had not ping to 192.168.2.1. Also I had not any other connection, not wireless nor cable, but (!) I still had ping to 192.168.2.100 and I not understand what this voodoo is... C:\Users\Andrey>ping 192.168.2.100 Pinging 192.168.2.100 with 32 bytes of data: Reply from 192.168.2.100: bytes=32 time<1ms TTL=128 Reply from 192.168.2.100: bytes=32 time<1ms TTL=128 Reply from 192.168.2.100: bytes=32 time<1ms TTL=128 Reply from 192.168.2.100: bytes=32 time<1ms TTL=128 Ping statistics for 192.168.2.100: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms This is what I had: C:\Users\Andrey>ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : Andrey-PC Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No Wireless LAN adapter Wireless Network Connection 3: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Microsoft Virtual WiFi Miniport Adapter #2 Physical Address. . . . . . . . . : 06-1D-7D-40-61-EB DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Wireless LAN adapter Wireless Network Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Gigabyte GN-WS50G (mini) PCI-E WLAN Card Physical Address. . . . . . . . . : 00-1D-7D-40-61-EB DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Ethernet adapter Local Area Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Marvell Yukon 88E8055 PCI-E Gigabit Ethernet Controller Physical Address. . . . . . . . . : 00-1B-24-B6-09-91 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes C:\Users\Andrey>arp -a -v Interface: 127.0.0.1 --- 0x1 Internet Address Physical Address Type 224.0.0.22 static 239.255.255.250 static Interface: 0.0.0.0 --- 0xffffffff Internet Address Physical Address Type 192.168.2.1 00-0e-2e-d2-8c-af invalid 192.168.2.255 ff-ff-ff-ff-ff-ff static 224.0.0.22 01-00-5e-00-00-16 static 224.0.0.252 01-00-5e-00-00-fc static 239.255.255.250 01-00-5e-7f-ff-fa static 255.255.255.255 ff-ff-ff-ff-ff-ff static Interface: 0.0.0.0 --- 0xffffffff Internet Address Physical Address Type 192.168.2.1 00-0e-2e-ff-f1-f6 dynamic 192.168.2.101 00-27-19-bc-8b-9c dynamic 192.168.2.102 00-16-e6-6c-ae-d4 dynamic 192.168.2.255 ff-ff-ff-ff-ff-ff static 224.0.0.22 01-00-5e-00-00-16 static 224.0.0.252 01-00-5e-00-00-fc static 239.255.255.250 01-00-5e-7f-ff-fa static 255.255.255.255 ff-ff-ff-ff-ff-ff static Interface: 0.0.0.0 --- 0xffffffff Internet Address Physical Address Type 224.0.0.22 01-00-5e-00-00-16 static 255.255.255.255 ff-ff-ff-ff-ff-ff static C:\Users\Andrey>route print =========================================================================== Interface List 14...06 1d 7d 40 61 eb ......Microsoft Virtual WiFi Miniport Adapter #2 13...00 1d 7d 40 61 eb ......Gigabyte GN-WS50G (mini) PCI-E WLAN Card 11...00 1b 24 b6 09 91 ......Marvell Yukon 88E8055 PCI-E Gigabit Ethernet Controller 1...........................Software Loopback Interface 1 =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 =========================================================================== Persistent Routes: None IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 1 306 ::1/128 On-link 1 306 ff00::/8 On-link =========================================================================== Persistent Routes: None Only after reboot I lost ping to there: C:\Users\Andrey>ping 192.168.2.100 Pinging 192.168.2.100 with 32 bytes of data: PING: transmit failed. General failure. PING: transmit failed. General failure. PING: transmit failed. General failure. PING: transmit failed. General failure. Ping statistics for 192.168.2.100: Packets: Sent = 4, Received = 0, Lost = 4 (100% loss), So what this mysterious cache is? Thank you for ahead.

  Read the article

• OpenVPN Client timing out

  - by Austin

  I recently installed OpenVPN on my Ubuntu VPS. Whenenver I try to connect to it, I can establish a connection just fine. However, everything I try to connect to times out. If I try to ping something, it will resolve the IP, but will time out after resolving the IP. (So DNS Server seems to be working correctly) My server.conf has this relevant information (At least I think it's relevant. I'm not sure if you need more or not) # Which local IP address should OpenVPN # listen on? (optional) ;local a.b.c.d # Which TCP/UDP port should OpenVPN listen on? # If you want to run multiple OpenVPN instances # on the same machine, use a different port # number for each one. You will need to # open up this port on your firewall. port 1194 # TCP or UDP server? ;proto tcp proto udp # "dev tun" will create a routed IP tunnel, # "dev tap" will create an ethernet tunnel. # Use "dev tap0" if you are ethernet bridging # and have precreated a tap0 virtual interface # and bridged it with your ethernet interface. # If you want to control access policies # over the VPN, you must create firewall # rules for the the TUN/TAP interface. # On non-Windows systems, you can give # an explicit unit number, such as tun0. # On Windows, use "dev-node" for this. # On most systems, the VPN will not function # unless you partially or fully disable # the firewall for the TUN/TAP interface. ;dev tap dev tun # Windows needs the TAP-Win32 adapter name # from the Network Connections panel if you # have more than one. On XP SP2 or higher, # you may need to selectively disable the # Windows firewall for the TAP adapter. # Non-Windows systems usually don't need this. ;dev-node MyTap # SSL/TLS root certificate (ca), certificate # (cert), and private key (key). Each client # and the server must have their own cert and # key file. The server and all clients will # use the same ca file. # # See the "easy-rsa" directory for a series # of scripts for generating RSA certificates # and private keys. Remember to use # a unique Common Name for the server # and each of the client certificates. # # Any X509 key management system can be used. # OpenVPN can also use a PKCS #12 formatted key file # (see "pkcs12" directive in man page). ca ca.crt cert server.crt key server.key # This file should be kept secret # Diffie hellman parameters. # Generate your own with: # openssl dhparam -out dh1024.pem 1024 # Substitute 2048 for 1024 if you are using # 2048 bit keys. dh dh1024.pem # Configure server mode and supply a VPN subnet # for OpenVPN to draw client addresses from. # The server will take 10.8.0.1 for itself, # the rest will be made available to clients. # Each client will be able to reach the server # on 10.8.0.1. Comment this line out if you are # ethernet bridging. See the man page for more info. server 10.8.0.0 255.255.255.0 # Maintain a record of client <-> virtual IP address # associations in this file. If OpenVPN goes down or # is restarted, reconnecting clients can be assigned # the same virtual IP address from the pool that was # previously assigned. ifconfig-pool-persist ipp.txt # Configure server mode for ethernet bridging. # You must first use your OS's bridging capability # to bridge the TAP interface with the ethernet # NIC interface. Then you must manually set the # IP/netmask on the bridge interface, here we # assume 10.8.0.4/255.255.255.0. Finally we # must set aside an IP range in this subnet # (start=10.8.0.50 end=10.8.0.100) to allocate # to connecting clients. Leave this line commented # out unless you are ethernet bridging. ;server-bridge 10.8.0.4 255.255.255.0 10.8.0.50 10.8.0.100 # Configure server mode for ethernet bridging # using a DHCP-proxy, where clients talk # to the OpenVPN server-side DHCP server # to receive their IP address allocation # and DNS server addresses. You must first use # your OS's bridging capability to bridge the TAP # interface with the ethernet NIC interface. # Note: this mode only works on clients (such as # Windows), where the client-side TAP adapter is # bound to a DHCP client. ;server-bridge # Push routes to the client to allow it # to reach other private subnets behind # the server. Remember that these # private subnets will also need # to know to route the OpenVPN client # address pool (10.8.0.0/255.255.255.0) # back to the OpenVPN server. ;push "route 192.168.10.0 255.255.255.0" ;push "route 192.168.20.0 255.255.255.0" # To assign specific IP addresses to specific # clients or if a connecting client has a private # subnet behind it that should also have VPN access, # use the subdirectory "ccd" for client-specific # configuration files (see man page for more info). # EXAMPLE: Suppose the client # having the certificate common name "Thelonious" # also has a small subnet behind his connecting # machine, such as 192.168.40.128/255.255.255.248. # First, uncomment out these lines: ;client-config-dir ccd ;route 192.168.40.128 255.255.255.248 # Then create a file ccd/Thelonious with this line: # iroute 192.168.40.128 255.255.255.248 # This will allow Thelonious' private subnet to # access the VPN. This example will only work # if you are routing, not bridging, i.e. you are # using "dev tun" and "server" directives. # EXAMPLE: Suppose you want to give # Thelonious a fixed VPN IP address of 10.9.0.1. # First uncomment out these lines: ;client-config-dir ccd ;route 10.9.0.0 255.255.255.252 # Then add this line to ccd/Thelonious: # ifconfig-push 10.9.0.1 10.9.0.2 # Suppose that you want to enable different # firewall access policies for different groups # of clients. There are two methods: # (1) Run multiple OpenVPN daemons, one for each # group, and firewall the TUN/TAP interface # for each group/daemon appropriately. # (2) (Advanced) Create a script to dynamically # modify the firewall in response to access # from different clients. See man # page for more info on learn-address script. ;learn-address ./script # If enabled, this directive will configure # all clients to redirect their default # network gateway through the VPN, causing # all IP traffic such as web browsing and # and DNS lookups to go through the VPN # (The OpenVPN server machine may need to NAT # or bridge the TUN/TAP interface to the internet # in order for this to work properly). push "redirect-gateway def1 bypass-dhcp" push "dhcp-option DNS 8.8.8.8" # Certain Windows-specific network settings # can be pushed to clients, such as DNS # or WINS server addresses. CAVEAT: # http://openvpn.net/faq.html#dhcpcaveats # The addresses below refer to the public # DNS servers provided by opendns.com. ;push "dhcp-option DNS 8.8.8.8" push "dhcp-option DNS 8.8.4.4" # Uncomment this directive to allow different # clients to be able to "see" each other. # By default, clients will only see the server. # To force clients to only see the server, you # will also need to appropriately firewall the # server's TUN/TAP interface. ;client-to-client # Uncomment this directive if multiple clients # might connect with the same certificate/key # files or common names. This is recommended # only for testing purposes. For production use, # each client should have its own certificate/key # pair. # # IF YOU HAVE NOT GENERATED INDIVIDUAL # CERTIFICATE/KEY PAIRS FOR EACH CLIENT, # EACH HAVING ITS OWN UNIQUE "COMMON NAME", # UNCOMMENT THIS LINE OUT. ;duplicate-cn # The keepalive directive causes ping-like # messages to be sent back and forth over # the link so that each side knows when # the other side has gone down. # Ping every 10 seconds, assume that remote # peer is down if no ping received during # a 120 second time period. keepalive 10 120 # For extra security beyond that provided # by SSL/TLS, create an "HMAC firewall" # to help block DoS attacks and UDP port flooding. # # Generate with: # openvpn --genkey --secret ta.key # # The server and each client must have # a copy of this key. # The second parameter should be '0' # on the server and '1' on the clients. ;tls-auth ta.key 0 # This file is secret # Select a cryptographic cipher. # This config item must be copied to # the client config file as well. ;cipher BF-CBC # Blowfish (default) ;cipher AES-128-CBC # AES ;cipher DES-EDE3-CBC # Triple-DES # Enable compression on the VPN link. # If you enable it here, you must also # enable it in the client config file. comp-lzo # The maximum number of concurrently connected # clients we want to allow. ;max-clients 100 # It's a good idea to reduce the OpenVPN # daemon's privileges after initialization. # # You can uncomment this out on # non-Windows systems. ;user nobody ;group nogroup # The persist options will try to avoid # accessing certain resources on restart # that may no longer be accessible because # of the privilege downgrade. persist-key persist-tun # Output a short status file showing # current connections, truncated # and rewritten every minute. status openvpn-status.log # By default, log messages will go to the syslog (or # on Windows, if running as a service, they will go to # the "\Program Files\OpenVPN\log" directory). # Use log or log-append to override this default. # "log" will truncate the log file on OpenVPN startup, # while "log-append" will append to it. Use one # or the other (but not both). ;log openvpn.log ;log-append openvpn.log # Set the appropriate level of log # file verbosity. # # 0 is silent, except for fatal errors # 4 is reasonable for general usage # 5 and 6 can help to debug connection problems # 9 is extremely verbose verb 3 # Silence repeating messages. At most 20 # sequential messages of the same message # category will be output to the log. ;mute 20 I've tried on multiple computers by the way. The same result on all of them. What could be wrong? Thanks in advance, and if you need other information I'll gladly post it. Information for new comments root@vps:~# iptables -L -n -v Chain INPUT (policy ACCEPT 862K packets, 51M bytes) pkts bytes target prot opt in out source destination Chain FORWARD (policy ACCEPT 3 packets, 382 bytes) pkts bytes target prot opt in out source destination 0 0 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 4641 298K ACCEPT all -- * * 10.8.0.0/24 0.0.0.0/0 0 0 REJECT all -- * * 0.0.0.0/0 0.0.0.0/0 reject-with icmp-port-unreachable Chain OUTPUT (policy ACCEPT 1671K packets, 2378M bytes) pkts bytes target prot opt in out source destination And root@vps:~# iptables -t nat -L -n -v Chain PREROUTING (policy ACCEPT 17937 packets, 2013K bytes) pkts bytes target prot opt in out source destination Chain POSTROUTING (policy ACCEPT 8975 packets, 562K bytes) pkts bytes target prot opt in out source destination 1579 103K SNAT all -- * * 10.8.0.0/24 0.0.0.0/0 to:SERVERIP Chain OUTPUT (policy ACCEPT 8972 packets, 562K bytes) pkts bytes target prot opt in out source destination

  Read the article

• Set up linux box for secure local hosting a-z

  - by microchasm

  I am in the process of reinstalling the OS on a machine that will be used to host a couple of apps for our business. The apps will be local only; access from external clients will be via vpn only. The prior setup used a hosting control panel (Plesk) for most of the admin, and I was looking at using another similar piece of software for the reinstall - but I figured I should finally learn how it all works. I can do most of the things the software would do for me, but am unclear on the symbiosis of it all. This is all an attempt to further distance myself from the land of Configuration Programmer/Programmer, if at all possible. I can't find a full walkthrough anywhere for what I'm looking for, so I thought I'd put up this question, and if people can help me on the way I will edit this with the answers, and document my progress/pitfalls. Hopefully someday this will help someone down the line. The details: CentOS 5.5 x86_64 httpd: Apache/2.2.3 mysql: 5.0.77 (to be upgraded) php: 5.1 (to be upgraded) The requirements: SECURITY!! Secure file transfer Secure client access (SSL Certs and CA) Secure data storage Virtualhosts/multiple subdomains Local email would be nice, but not critical The Steps: Download latest CentOS DVD-iso (torrent worked great for me). Install CentOS: While going through the install, I checked the Server Components option thinking I was going to be using another Plesk-like admin. In hindsight, considering I've decided to try to go my own way, this probably wasn't the best idea. Basic config: Setup users, networking/ip address etc. Yum update/upgrade. Upgrade PHP/MySQL: To upgrade PHP and MySQL to the latest versions, I had to look to another repo outside CentOS. IUS looks great and I'm happy I found it! Add IUS repository to our package manager cd /tmp wget http://dl.iuscommunity.org/pub/ius/stable/Redhat/5/x86_64/epel-release-1-1.ius.el5.noarch.rpm rpm -Uvh epel-release-1-1.ius.el5.noarch.rpm wget http://dl.iuscommunity.org/pub/ius/stable/Redhat/5/x86_64/ius-release-1-4.ius.el5.noarch.rpm rpm -Uvh ius-release-1-4.ius.el5.noarch.rpm yum list | grep -w \.ius\. # list all the packages in the IUS repository; use this to find PHP/MySQL version and libraries you want to install Remove old version of PHP and install newer version from IUS rpm -qa | grep php # to list all of the installed php packages we want to remove yum shell # open an interactive yum shell remove php-common php-mysql php-cli #remove installed PHP components install php53 php53-mysql php53-cli php53-common #add packages you want transaction solve #important!! checks for dependencies transaction run #important!! does the actual installation of packages. [control+d] #exit yum shell php -v PHP 5.3.2 (cli) (built: Apr 6 2010 18:13:45) Upgrade MySQL from IUS repository /etc/init.d/mysqld stop rpm -qa | grep mysql # to see installed mysql packages yum shell remove mysql mysql-server #remove installed MySQL components install mysql51 mysql51-server mysql51-devel transaction solve #important!! checks for dependencies transaction run #important!! does the actual installation of packages. [control+d] #exit yum shell service mysqld start mysql -v Server version: 5.1.42-ius Distributed by The IUS Community Project Upgrade instructions courtesy of IUS wiki: http://wiki.iuscommunity.org/Doc/ClientUsageGuide Install rssh (restricted shell) to provide scp and sftp access, without allowing ssh login cd /tmp wget http://dag.wieers.com/rpm/packages/rssh/rssh-2.3.2-1.2.el5.rf.x86_64.rpm rpm -ivh rssh-2.3.2-1.2.el5.rf.x86_64.rpm useradd -m -d /home/dev -s /usr/bin/rssh dev passwd dev Edit /etc/rssh.conf to grant access to SFTP to rssh users. vi /etc/rssh.conf Uncomment or add: allowscp allowsftp This allows me to connect to the machine via SFTP protocol in Transmit (my FTP program of choice; I'm sure it's similar with other FTP apps). rssh instructions appropriated (with appreciation!) from http://www.cyberciti.biz/tips/linux-unix-restrict-shell-access-with-rssh.html Set up virtual interfaces ifconfig eth1:1 192.168.1.3 up #start up the virtual interface cd /etc/sysconfig/network-scripts/ cp ifcfg-eth1 ifcfg-eth1:1 #copy default script and match name to our virtual interface vi ifcfg-eth1:1 #modify eth1:1 script #ifcfg-eth1:1 | modify so it looks like this: DEVICE=eth1:1 IPADDR=192.168.1.3 NETMASK=255.255.255.0 NETWORK=192.168.1.0 ONBOOT=yes NAME=eth1:1 Add more Virtual interfaces as needed by repeating. Because of the ONBOOT=yes line in the ifcfg-eth1:1 file, this interface will be brought up when the system boots, or the network starts/restarts. service network restart Shutting down interface eth0: [ OK ] Shutting down interface eth1: [ OK ] Shutting down loopback interface: [ OK ] Bringing up loopback interface: [ OK ] Bringing up interface eth0: [ OK ] Bringing up interface eth1: [ OK ] ping 192.168.1.3 64 bytes from 192.168.1.3: icmp_seq=1 ttl=64 time=0.105 ms Virtualhosts In the rssh section above I added a user to use for SFTP. In this users' home directory, I created a folder called 'https'. This is where the documents for this site will live, so I need to add a virtualhost that will point to it. I will use the above virtual interface for this site (herein called dev.site.local). vi /etc/http/conf/httpd.conf Add the following to the end of httpd.conf: <VirtualHost 192.168.1.3:80> ServerAdmin [email protected] DocumentRoot /home/dev/https ServerName dev.site.local ErrorLog /home/dev/logs/error_log TransferLog /home/dev/logs/access_log </VirtualHost> I put a dummy index.html file in the https directory just to check everything out. I tried browsing to it, and was met with permission denied errors. The logs only gave an obscure reference to what was going on: [Mon May 17 14:57:11 2010] [error] [client 192.168.1.100] (13)Permission denied: access to /index.html denied I tried chmod 777 et. al., but to no avail. Turns out, I needed to chmod+x the https directory and its' parent directories. chmod +x /home chmod +x /home/dev chmod +x /home/dev/https This solved that problem. DNS I'm handling DNS via our local Windows Server 2003 box. However, the CentOS documentation for BIND can be found here: http://www.centos.org/docs/5/html/Deployment_Guide-en-US/ch-bind.html SSL To get SSL working, I changed the following in httpd.conf: NameVirtualHost 192.168.1.3:443 #make sure this line is in httpd.conf <VirtualHost 192.168.1.3:443> #change port to 443 ServerAdmin [email protected] DocumentRoot /home/dev/https ServerName dev.site.local ErrorLog /home/dev/logs/error_log TransferLog /home/dev/logs/access_log </VirtualHost> Unfortunately, I keep getting (Error code: ssl_error_rx_record_too_long) errors when trying to access a page with SSL. As JamesHannah gracefully pointed out below, I had not set up the locations of the certs in httpd.conf, and thusly was getting the page thrown at the broswer as the cert making the browser balk. So first, I needed to set up a CA and make certificate files. I found a great (if old) walkthrough on the process here: http://www.debian-administration.org/articles/284. Here are the relevant steps I took from that article: mkdir /home/CA cd /home/CA/ mkdir newcerts private echo '01' > serial touch index.txt #this and the above command are for the database that will keep track of certs Create an openssl.cnf file in the /home/CA/ dir and edit it per the walkthrough linked above. (For reference, my finished openssl.cnf file looked like this: http://pastebin.com/raw.php?i=hnZDij4T) openssl req -new -x509 -extensions v3_ca -keyout private/cakey.pem -out cacert.pem -days 3650 -config ./openssl.cnf #this creates the cacert.pem which gets distributed and imported to the browser(s) Modified openssl.cnf again per walkthrough instructions. openssl req -new -nodes -out dev.req.pem -config ./openssl.cnf #generates certificate request, and key.pem which I renamed dev.key.pem. Modified openssl.cnf again per walkthrough instructions. openssl ca -out dev.cert.pem -config ./openssl.cnf -infiles dev.req.pem #create and sign certificate. cp dev.cert.pem /home/dev/certs/cert.pem cp dev.key.pem /home/certs/key.pem I updated httpd.conf to reflect the certs and turn SSLEngine on: NameVirtualHost 192.168.1.3:443 <VirtualHost 192.168.1.3:443> ServerAdmin [email protected] DocumentRoot /home/dev/https SSLEngine on SSLCertificateFile /home/dev/certs/cert.pem SSLCertificateKeyFile /home/dev/certs/key.pem ServerName dev.site.local ErrorLog /home/dev/logs/error_log TransferLog /home/dev/logs/access_log </VirtualHost> Put the CA cert.pem in a web-accessible place, and downloaded/imported it into my browser. Now I can visit https://dev.site.local with no errors or warnings. And this is where I'm at. I will keep editing this as I make progress. Any tips on how to configure SSL email would be appreciated.

  Read the article

• connecting to a network using route command

  - by ami

  I have a computer with an external IP(192.168.223.220) and also an internal address (10.1.1.20) in order to connect to some servers that don't have external addresses only 10.1.1.xx . in order to connect to these servers from other machines I used the following command "route ADD 10.1.1.0 MASK 255.255.255.0 192.168.223.220" and than I was able to connect to the servers using there 10.1.1.xx address. The problem is that the hard disk of main server(192.168.223.220) died and was replaced and after the that I am not able to connect to the servers as before, the route command succeeds and I can ping 10.1.1.20 but not the other servers. Thanks I am using Windows XP and the print outs are D:\AurosHome\Scriptsipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : N100-master Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Unknown IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No Ethernet adapter Local Area Connection 3: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Intel(R) PRO/1000 EB Network Connection with I/O Acceleration #2 Physical Address. . . . . . . . . : 00-30-48-34-BA-B9 Dhcp Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 192.168.225.180 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.225.254 DNS Servers . . . . . . . . . . . : 192.168.225.2 Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Intel(R) PRO/1000 EB Network Connection with I/O Acceleration Physical Address. . . . . . . . . : 00-30-48-34-BA-B8 Dhcp Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 10.1.1.20 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : Ethernet adapter Local Area Connection 2: Media State . . . . . . . . . . . : Media disconnected Description . . . . . . . . . . . : Mellanox IPoIB Adapter Physical Address. . . . . . . . . : 00-02-C9-25-34-0D D:\AurosHome\Scriptsroute print Interface List 0x1 ........................... MS TCP Loopback interface 0x2 ...00 30 48 34 ba b9 ...... Intel(R) PRO/1000 EB Network Connection with I/O Acceleration #2 - Packet Sche duler Miniport 0x3 ...00 30 48 34 ba b8 ...... Intel(R) PRO/1000 EB Network Connection with I/O Acceleration - Packet Schedul er Miniport 0x10005 ...00 02 c9 25 34 0d ...... Mellanox IPoIB Adapter - Packet Scheduler Miniport =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.225.254 192.168.225.180 10 10.1.1.0 255.255.255.0 10.1.1.20 10.1.1.20 10 10.1.1.20 255.255.255.255 127.0.0.1 127.0.0.1 10 10.255.255.255 255.255.255.255 10.1.1.20 10.1.1.20 10 127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1 192.168.225.0 255.255.255.0 192.168.225.180 192.168.225.180 10 192.168.225.180 255.255.255.255 127.0.0.1 127.0.0.1 10 192.168.225.255 255.255.255.255 192.168.225.180 192.168.225.180 10 224.0.0.0 240.0.0.0 10.1.1.20 10.1.1.20 10 224.0.0.0 240.0.0.0 192.168.225.180 192.168.225.180 10 255.255.255.255 255.255.255.255 10.1.1.20 10.1.1.20 1 255.255.255.255 255.255.255.255 10.1.1.20 10005 1 255.255.255.255 255.255.255.255 192.168.225.180 192.168.225.180 1 Default Gateway: 192.168.225.254 Persistent Routes: None

  Read the article

• Windows Server 2003 VPN and Local network

  - by depo

  I have some problems reaching local network , where VPN Windows 2003 server stands. I have a network, which has a VPN server (LAN ip 10.0.0.201). I created a VPN server on that server with different subnet for VPN users (10.0.5.0). After VPN connection is initiated , i am able to acces only 10.0.0.201, but not other PC, which belongs to that network ( all i need to access 10.0.0.203 and 10.0.0.208). I think i need to add somethink to static route table, or not? C:\Documents and Settings\Administratorroute PRINT IPv4 Route Table Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.0.0.254 10.0.0.201 10 10.0.0.0 255.0.0.0 10.0.0.201 10.0.0.201 10 10.0.0.201 255.255.255.255 127.0.0.1 127.0.0.1 10 10.0.5.1 255.255.255.255 127.0.0.1 127.0.0.1 50 10.255.255.255 255.255.255.255 10.0.0.201 10.0.0.201 10 127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1 224.0.0.0 240.0.0.0 10.0.0.201 10.0.0.201 10 255.255.255.255 255.255.255.255 10.0.0.201 10.0.0.201 1 Default Gateway: 10.0.0.254 Persistent Routes: None C:\Documents and Settings\Administratoripconfig /all PPP adapter RAS Server (Dial In) Interface: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : WAN (PPP/SLIP) Interface Physical Address. . . . . . . . . : 00-53-45-00-00-00 DHCP Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 10.0.5.1 Subnet Mask . . . . . . . . . . . : 255.255.255.255 Default Gateway . . . . . . . . . : Ethernet adapter Local Area Connection 2: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Intel(R) PRO/1000 MT Network Connection Physical Address. . . . . . . . . : 00-0E-0C-3D-C9-51 DHCP Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 10.0.0.201 Subnet Mask . . . . . . . . . . . : 255.0.0.0 Default Gateway . . . . . . . . . : 10.0.0.254 DNS Servers . . . . . . . . . . . : 127.0.0.1 Primary WINS Server . . . . . . . : 10.0.0.201 NetBIOS over Tcpip. . . . . . . . : Disabled VPN Client PPP adapter VPN Connection 2: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : VPN Connection 2 Physical Address. . . . . . . . . : DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 10.0.5.4(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.255 Default Gateway . . . . . . . . . : DNS Servers . . . . . . . . . . . : 10.0.0.201 Primary WINS Server . . . . . . . : 10.0.0.201 NetBIOS over Tcpip. . . . . . . . : Enabled

  Read the article

• unexplainable packet drops with 5 ethernet NICs and low traffic on Ubuntu

  - by jon

  I'm stuck on problem where my machine started to drops packets with no sign of ANY system load or high interrupt usage after an upgrade to Ubuntu 12.04. My server is a network monitoring sensor, running Ubuntu LTS 12.04, it passively collects packets from 5 interfaces doing network intrusion type stuff. Before the upgrade I managed to collect 200+GB of packets a day while writing them to disk with around 0% packet loss depending on the day with the help of CPU affinity and NIC IRQ to CPU bindings. Now I lose a great deal of packets with none of my applications running and at very low PPS rate which a modern workstation NIC would have no trouble with. Specs: x64 Xeon 4 cores 3.2 Ghz 16 GB RAM NICs: 5 Intel Pro NICs using the e1000 driver (NAPI). [1] eth0 and eth1 are integrated NICs (in the motherboard) There are 2 other PCI-X network cards, each with 2 Ethernet ports. 3 of the interfaces are running at Gigabit Ethernet, the others are not because they're attached to hubs. Specs: [2] http://support.dell.com/support/edocs/systems/pe2850/en/ug/t1390aa.htm uptime 17:36:00 up 1:43, 2 users, load average: 0.00, 0.01, 0.05 # uname -a Linux nms 3.2.0-29-generic #46-Ubuntu SMP Fri Jul 27 17:03:23 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux I also have the CPU governor set to performance mode and irqbalance off. The problem still occurs with them on. # lspci -t -vv -[0000:00]-+-00.0 Intel Corporation E7520 Memory Controller Hub +-02.0-[01-03]--+-00.0-[02]----0e.0 Dell PowerEdge Expandable RAID controller 4 | \-00.2-[03]-- +-04.0-[04]-- +-05.0-[05-07]--+-00.0-[06]----07.0 Intel Corporation 82541GI Gigabit Ethernet Controller | \-00.2-[07]----08.0 Intel Corporation 82541GI Gigabit Ethernet Controller +-06.0-[08-0a]--+-00.0-[09]--+-04.0 Intel Corporation 82546EB Gigabit Ethernet Controller (Copper) | | \-04.1 Intel Corporation 82546EB Gigabit Ethernet Controller (Copper) | \-00.2-[0a]--+-02.0 Digium, Inc. Wildcard TE210P/TE212P dual-span T1/E1/J1 card 3.3V | +-03.0 Intel Corporation 82546EB Gigabit Ethernet Controller (Copper) | \-03.1 Intel Corporation 82546EB Gigabit Ethernet Controller (Copper) +-1d.0 Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #1 +-1d.1 Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #2 +-1d.2 Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #3 +-1d.7 Intel Corporation 82801EB/ER (ICH5/ICH5R) USB2 EHCI Controller +-1e.0-[0b]----0d.0 Advanced Micro Devices [AMD] nee ATI RV100 QY [Radeon 7000/VE] +-1f.0 Intel Corporation 82801EB/ER (ICH5/ICH5R) LPC Interface Bridge \-1f.1 Intel Corporation 82801EB/ER (ICH5/ICH5R) IDE Controller I believe the NIC nor the NIC drivers are dropping the packets because ethtool reports 0 under rx_missed_errors and rx_no_buffer_count for each interface. On the old system, if it couldn't keep up this is where the drops would be. I drop packets on multiple interfaces just about every second, usually in small increments of 2-4. I tried all these sysctl values, I'm currently using the uncommented ones. # cat /etc/sysctl.conf # high net.core.netdev_max_backlog = 3000000 net.core.rmem_max = 16000000 net.core.rmem_default = 8000000 # defaults #net.core.netdev_max_backlog = 1000 #net.core.rmem_max = 131071 #net.core.rmem_default = 163480 # moderate #net.core.netdev_max_backlog = 10000 #net.core.rmem_max = 33554432 #net.core.rmem_default = 33554432 Here's an example of an interface stats report with ethtool. They are all the same, nothing is out of the ordinary ( I think ), so I'm only going to show one: ethtool -S eth2 NIC statistics: rx_packets: 7498 tx_packets: 0 rx_bytes: 2722585 tx_bytes: 0 rx_broadcast: 327 tx_broadcast: 0 rx_multicast: 1504 tx_multicast: 0 rx_errors: 0 tx_errors: 0 tx_dropped: 0 multicast: 1504 collisions: 0 rx_length_errors: 0 rx_over_errors: 0 rx_crc_errors: 0 rx_frame_errors: 0 rx_no_buffer_count: 0 rx_missed_errors: 0 tx_aborted_errors: 0 tx_carrier_errors: 0 tx_fifo_errors: 0 tx_heartbeat_errors: 0 tx_window_errors: 0 tx_abort_late_coll: 0 tx_deferred_ok: 0 tx_single_coll_ok: 0 tx_multi_coll_ok: 0 tx_timeout_count: 0 tx_restart_queue: 0 rx_long_length_errors: 0 rx_short_length_errors: 0 rx_align_errors: 0 tx_tcp_seg_good: 0 tx_tcp_seg_failed: 0 rx_flow_control_xon: 0 rx_flow_control_xoff: 0 tx_flow_control_xon: 0 tx_flow_control_xoff: 0 rx_long_byte_count: 2722585 rx_csum_offload_good: 0 rx_csum_offload_errors: 0 alloc_rx_buff_failed: 0 tx_smbus: 0 rx_smbus: 0 dropped_smbus: 01 # ifconfig eth0 Link encap:Ethernet HWaddr 00:11:43:e0:e2:8c UP BROADCAST RUNNING NOARP PROMISC ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:373348 errors:16 dropped:95 overruns:0 frame:16 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:356830572 (356.8 MB) TX bytes:0 (0.0 B) eth1 Link encap:Ethernet HWaddr 00:11:43:e0:e2:8d UP BROADCAST RUNNING NOARP PROMISC ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:13616 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:8690528 (8.6 MB) TX bytes:0 (0.0 B) eth2 Link encap:Ethernet HWaddr 00:04:23:e1:77:6a UP BROADCAST RUNNING NOARP PROMISC ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:7750 errors:0 dropped:471 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2780935 (2.7 MB) TX bytes:0 (0.0 B) eth3 Link encap:Ethernet HWaddr 00:04:23:e1:77:6b UP BROADCAST RUNNING NOARP PROMISC ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:5112 errors:0 dropped:206 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:639472 (639.4 KB) TX bytes:0 (0.0 B) eth4 Link encap:Ethernet HWaddr 00:04:23:b6:35:6c UP BROADCAST RUNNING NOARP PROMISC ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:961467 errors:0 dropped:935 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:958561305 (958.5 MB) TX bytes:0 (0.0 B) eth5 Link encap:Ethernet HWaddr 00:04:23:b6:35:6d inet addr:192.168.1.6 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4264 errors:0 dropped:16 overruns:0 frame:0 TX packets:699 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:572228 (572.2 KB) TX bytes:124456 (124.4 KB) I tried the defaults, then started to play around with settings. I wasn't using any flow control and I increased the RxDescriptor count to 4096 before the upgrade as well without any problems. # cat /etc/modprobe.d/e1000.conf options e1000 XsumRX=0,0,0,0,0 RxDescriptors=4096,4096,4096,4096,4096 FlowControl=0,0,0,0,0 debug=16 Here's my network configuration file, I turned off checksumming and various offloading mechanisms along with setting CPU affinity with heavy use interfaces getting an entire CPU and light use interfaces sharing a CPU. I used these settings prior to the upgrade without problems. # cat /etc/network/interfaces # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet manual pre-up /sbin/ethtool -G eth0 rx 4096 tx 0 pre-up /sbin/ethtool -K eth0 gro off gso off rx off pre-up /sbin/ethtool -A eth0 rx off autoneg off up ifconfig eth0 0.0.0.0 -arp promisc mtu 1500 allmulti txqueuelen 0 up post-up echo "4" > /proc/irq/48/smp_affinity down ifconfig eth0 down post-down /sbin/ethtool -G eth0 rx 256 tx 256 post-down /sbin/ethtool -K eth0 gro on gso on rx on post-down /sbin/ethtool -A eth0 rx on autoneg on auto eth1 iface eth1 inet manual pre-up /sbin/ethtool -G eth1 rx 4096 tx 0 pre-up /sbin/ethtool -K eth1 gro off gso off rx off pre-up /sbin/ethtool -A eth1 rx off autoneg off up ifconfig eth1 0.0.0.0 -arp promisc mtu 1500 allmulti txqueuelen 0 up post-up echo "4" > /proc/irq/49/smp_affinity down ifconfig eth1 down post-down /sbin/ethtool -G eth1 rx 256 tx 256 post-down /sbin/ethtool -K eth1 gro on gso on rx on post-down /sbin/ethtool -A eth1 rx on autoneg on auto eth2 iface eth2 inet manual pre-up /sbin/ethtool -G eth2 rx 4096 tx 0 pre-up /sbin/ethtool -K eth2 gro off gso off rx off pre-up /sbin/ethtool -A eth2 rx off autoneg off up ifconfig eth2 0.0.0.0 -arp promisc mtu 1500 allmulti txqueuelen 0 up post-up echo "1" > /proc/irq/82/smp_affinity down ifconfig eth2 down post-down /sbin/ethtool -G eth2 rx 256 tx 256 post-down /sbin/ethtool -K eth2 gro on gso on rx on post-down /sbin/ethtool -A eth2 rx on autoneg on auto eth3 iface eth3 inet manual pre-up /sbin/ethtool -G eth3 rx 4096 tx 0 pre-up /sbin/ethtool -K eth3 gro off gso off rx off pre-up /sbin/ethtool -A eth3 rx off autoneg off up ifconfig eth3 0.0.0.0 -arp promisc mtu 1500 allmulti txqueuelen 0 up post-up echo "2" > /proc/irq/83/smp_affinity down ifconfig eth3 down post-down /sbin/ethtool -G eth3 rx 256 tx 256 post-down /sbin/ethtool -K eth3 gro on gso on rx on post-down /sbin/ethtool -A eth3 rx on autoneg on auto eth4 iface eth4 inet manual pre-up /sbin/ethtool -G eth4 rx 4096 tx 0 pre-up /sbin/ethtool -K eth4 gro off gso off rx off pre-up /sbin/ethtool -A eth4 rx off autoneg off up ifconfig eth4 0.0.0.0 -arp promisc mtu 1500 allmulti txqueuelen 0 up post-up echo "4" > /proc/irq/77/smp_affinity down ifconfig eth4 down post-down /sbin/ethtool -G eth4 rx 256 tx 256 post-down /sbin/ethtool -K eth4 gro on gso on rx on post-down /sbin/ethtool -A eth4 rx on autoneg on auto eth5 iface eth5 inet static pre-up /etc/fw.conf address 192.168.1.1 netmask 255.255.255.0 broadcast 192.168.1.255 gateway 192.168.1.1 dns-nameservers 192.168.1.2 192.168.1.3 up ifconfig eth5 up post-up echo "8" > /proc/irq/77/smp_affinity down ifconfig eth5 down Here's a few examples of packet drops, i ran one after another, probabling totaling 3 or 4 seconds. You can see increases in the drops from the 1st and 3rd. This was a non-busy time, very little traffic. # awk '{ print $1,$5 }' /proc/net/dev Inter-| face drop eth3: 225 lo: 0 eth2: 505 eth1: 0 eth5: 17 eth0: 105 eth4: 1034 # awk '{ print $1,$5 }' /proc/net/dev Inter-| face drop eth3: 225 lo: 0 eth2: 507 eth1: 0 eth5: 17 eth0: 105 eth4: 1034 # awk '{ print $1,$5 }' /proc/net/dev Inter-| face drop eth3: 227 lo: 0 eth2: 512 eth1: 0 eth5: 17 eth0: 105 eth4: 1039 I tried the pci=noacpi options. With and without, it's the same. This is what my interrupt stats looked like before the upgrade, after, with ACPI on PCI it showed multiple NICs bound to an interrupt and shared with other devices such as USB drives which I didn't like so I think i'm going to keep it with ACPI off as it's easier to designate sole purpose interrupts. Is there any advantage I would have using the default i.e. ACPI w/ PCI. ? # cat /etc/default/grub | grep CMD_LINE GRUB_CMDLINE_LINUX_DEFAULT="ipv6.disable=1 noacpi pci=noacpi" GRUB_CMDLINE_LINUX="" # cat /proc/interrupts CPU0 CPU1 CPU2 CPU3 0: 45 0 0 16 IO-APIC-edge timer 1: 1 0 0 7936 IO-APIC-edge i8042 2: 0 0 0 0 XT-PIC-XT-PIC cascade 6: 0 0 0 3 IO-APIC-edge floppy 8: 0 0 0 1 IO-APIC-edge rtc0 9: 0 0 0 0 IO-APIC-edge acpi 12: 0 0 0 1809 IO-APIC-edge i8042 14: 1 0 0 4498 IO-APIC-edge ata_piix 15: 0 0 0 0 IO-APIC-edge ata_piix 16: 0 0 0 0 IO-APIC-fasteoi uhci_hcd:usb2 18: 0 0 0 1350 IO-APIC-fasteoi uhci_hcd:usb4, radeon 19: 0 0 0 0 IO-APIC-fasteoi uhci_hcd:usb3 23: 0 0 0 4099 IO-APIC-fasteoi ehci_hcd:usb1 38: 0 0 0 61963 IO-APIC-fasteoi megaraid 48: 0 0 1002319 4 IO-APIC-fasteoi eth0 49: 0 0 38772 3 IO-APIC-fasteoi eth1 77: 0 0 130076 432159 IO-APIC-fasteoi eth4 78: 0 0 0 23917 IO-APIC-fasteoi eth5 82: 1329033 0 0 4 IO-APIC-fasteoi eth2 83: 0 4886525 0 6 IO-APIC-fasteoi eth3 NMI: 5 6 4 5 Non-maskable interrupts LOC: 61409 57076 64257 114764 Local timer interrupts SPU: 0 0 0 0 Spurious interrupts IWI: 0 0 0 0 IRQ work interrupts RES: 17956 25333 13436 14789 Rescheduling interrupts CAL: 22436 607 539 478 Function call interrupts TLB: 1525 1458 4600 4151 TLB shootdowns TRM: 0 0 0 0 Thermal event interrupts THR: 0 0 0 0 Threshold APIC interrupts MCE: 0 0 0 0 Machine check exceptions MCP: 16 16 16 16 Machine check polls ERR: 0 MIS: 0 Here's sample output of vmstat, showing the system. Barebones system right now. root@nms:~# vmstat -S m 1 procs -----------memory---------- ---swap-- -----io---- -system-- ----cpu---- r b swpd free buff cache si so bi bo in cs us sy id wa 0 0 0 14992 192 1029 0 0 56 2 419 29 1 0 99 0 0 0 0 14992 192 1029 0 0 0 0 922 27 0 0 100 0 0 0 0 14991 192 1029 0 0 0 36 763 50 0 0 100 0 0 0 0 14991 192 1029 0 0 0 0 646 35 0 0 100 0 0 0 0 14991 192 1029 0 0 0 0 722 54 0 0 100 0 0 0 0 14991 192 1029 0 0 0 0 793 27 0 0 100 0 ^C Here's dmesg output. I can't figure out why my PCI-X slots are negotiated as PCI. The network cards are all PCI-X with the exception of the integrated NICs that came with the server. In the output below it looks as if eth3 and eth2 negotiated at PCI-X speeds rather than PCI:66Mhz. Wouldn't they all drop to PCI:66Mhz? If your integrated NICs are PCI, as labeled below (eth0,eth1), then wouldn't all devices on your bus speed drop down to that slower bus speed? If not, I still don't know why only one of my NICs ( each has two ethernet ports) is labeled as PCI-X in the output below. Does that mean it is running at PCI-X speeds are is it showing that it's capable? # dmesg | grep e1000 [ 3678.349337] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI [ 3678.349342] e1000: Copyright (c) 1999-2006 Intel Corporation. [ 3678.349394] e1000 0000:06:07.0: PCI->APIC IRQ transform: INT A -> IRQ 48 [ 3678.409725] e1000 0000:06:07.0: Receive Descriptors set to 4096 [ 3678.409730] e1000 0000:06:07.0: Checksum Offload Disabled [ 3678.409734] e1000 0000:06:07.0: Flow Control Disabled [ 3678.586409] e1000 0000:06:07.0: eth0: (PCI:66MHz:32-bit) 00:11:43:e0:e2:8c [ 3678.586419] e1000 0000:06:07.0: eth0: Intel(R) PRO/1000 Network Connection [ 3678.586642] e1000 0000:07:08.0: PCI->APIC IRQ transform: INT A -> IRQ 49 [ 3678.649854] e1000 0000:07:08.0: Receive Descriptors set to 4096 [ 3678.649859] e1000 0000:07:08.0: Checksum Offload Disabled [ 3678.649863] e1000 0000:07:08.0: Flow Control Disabled [ 3678.826436] e1000 0000:07:08.0: eth1: (PCI:66MHz:32-bit) 00:11:43:e0:e2:8d [ 3678.826444] e1000 0000:07:08.0: eth1: Intel(R) PRO/1000 Network Connection [ 3678.826627] e1000 0000:09:04.0: PCI->APIC IRQ transform: INT A -> IRQ 82 [ 3679.093266] e1000 0000:09:04.0: Receive Descriptors set to 4096 [ 3679.093271] e1000 0000:09:04.0: Checksum Offload Disabled [ 3679.093275] e1000 0000:09:04.0: Flow Control Disabled [ 3679.130239] e1000 0000:09:04.0: eth2: (PCI-X:133MHz:64-bit) 00:04:23:e1:77:6a [ 3679.130246] e1000 0000:09:04.0: eth2: Intel(R) PRO/1000 Network Connection [ 3679.130449] e1000 0000:09:04.1: PCI->APIC IRQ transform: INT B -> IRQ 83 [ 3679.397312] e1000 0000:09:04.1: Receive Descriptors set to 4096 [ 3679.397318] e1000 0000:09:04.1: Checksum Offload Disabled [ 3679.397321] e1000 0000:09:04.1: Flow Control Disabled [ 3679.434350] e1000 0000:09:04.1: eth3: (PCI-X:133MHz:64-bit) 00:04:23:e1:77:6b [ 3679.434360] e1000 0000:09:04.1: eth3: Intel(R) PRO/1000 Network Connection [ 3679.434553] e1000 0000:0a:03.0: PCI->APIC IRQ transform: INT A -> IRQ 77 [ 3679.704072] e1000 0000:0a:03.0: Receive Descriptors set to 4096 [ 3679.704077] e1000 0000:0a:03.0: Checksum Offload Disabled [ 3679.704081] e1000 0000:0a:03.0: Flow Control Disabled [ 3679.738364] e1000 0000:0a:03.0: eth4: (PCI:33MHz:64-bit) 00:04:23:b6:35:6c [ 3679.738371] e1000 0000:0a:03.0: eth4: Intel(R) PRO/1000 Network Connection [ 3679.738538] e1000 0000:0a:03.1: PCI->APIC IRQ transform: INT B -> IRQ 78 [ 3680.046060] e1000 0000:0a:03.1: eth5: (PCI:33MHz:64-bit) 00:04:23:b6:35:6d [ 3680.046067] e1000 0000:0a:03.1: eth5: Intel(R) PRO/1000 Network Connection [ 3682.132415] e1000: eth0 NIC Link is Up 100 Mbps Half Duplex, Flow Control: None [ 3682.224423] e1000: eth1 NIC Link is Up 100 Mbps Half Duplex, Flow Control: None [ 3682.316385] e1000: eth2 NIC Link is Up 100 Mbps Half Duplex, Flow Control: None [ 3682.408391] e1000: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None [ 3682.500396] e1000: eth4 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None [ 3682.708401] e1000: eth5 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX At first I thought it was the NIC drivers but I'm not so sure. I really have no idea where else to look at the moment. Any help is greatly appreciated as I'm struggling with this. If you need more information just ask. Thanks! [1]http://www.cs.fsu.edu/~baker/devices/lxr/http/source/linux/Documentation/networking/e1000.txt?v=2.6.11.8 [2] http://support.dell.com/support/edocs/systems/pe2850/en/ug/t1390aa.htm

  Read the article

• Ping "replies" from same computer with 'Destination host unreachable' (no route to other computer)

  - by Srekel

  I've got two computers in a LAN behind a wireless router. One has XP with ip 192.168.1.2 This one has W7 with ip 192.168.1.7 If I try to ping the other one from this computer, I get this: C:\Users\Srekel>ping 192.168.1.2 Pinging 192.168.1.2 with 32 bytes of data: Reply from 192.168.1.7: Destination host unreachable. Reply from 192.168.1.7: Destination host unreachable. Reply from 192.168.1.7: Destination host unreachable. Reply from 192.168.1.7: Destination host unreachable. Ping statistics for 192.168.1.2: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Tracert gives the same result: C:\Users\Srekel>tracert 192.168.1.2 Tracing route to 192.168.1.2 over a maximum of 30 hops 1 Kakburken4 [192.168.1.7] reports: Destination host unreachable. Trace complete. Although I can ping and tracert the router without any problems. I have disabled the firewalls on both computers. The router is set to use DHCP (if that matters). Here is the output from "route". C:\Users\Srekel>route print =========================================================================== Interface List 13...00 25 86 df c6 89 ......TP-LINK Wireless N Adapter 12...e0 cb 4e 26 b9 84 ......Realtek PCIe GBE Family Controller #2 11...e0 cb 4e 26 be 94 ......Realtek PCIe GBE Family Controller 1...........................Software Loopback Interface 1 16...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 14...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.7 20 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.1.0 255.255.255.0 On-link 192.168.1.7 276 192.168.1.7 255.255.255.255 On-link 192.168.1.7 276 192.168.1.255 255.255.255.255 On-link 192.168.1.7 276 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.1.7 276 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.1.7 276 =========================================================================== Persistent Routes: None IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 14 58 ::/0 On-link 1 306 ::1/128 On-link 14 58 2001::/32 On-link 14 306 2001:0:5ef5:73ba:881:20c1:3f57:fef8/128 On-link 14 306 fe80::/64 On-link 14 306 fe80::881:20c1:3f57:fef8/128 On-link 1 306 ff00::/8 On-link 14 306 ff00::/8 On-link =========================================================================== Persistent Routes: None I've set up and debugged a few networks in my life but I'm not really an advanced network user, so I'm not sure what might be wrong. Any ideas? Oh, and pinging this computer from the other computer doesn't work either. EDIT: Adding arp output: C:\Users\Srekel>arp -a Interface: 192.168.1.7 --- 0xd Internet Address Physical Address Type 192.168.1.1 00-1f-33-ef-28-01 dynamic 192.168.1.255 ff-ff-ff-ff-ff-ff static 224.0.0.22 01-00-5e-00-00-16 static 224.0.0.252 01-00-5e-00-00-fc static 239.255.255.250 01-00-5e-7f-ff-fa static 255.255.255.255 ff-ff-ff-ff-ff-ff static Adding ipconfig... C:\Users\Srekel>ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : Kakburken4 Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No Wireless LAN adapter Wireless Network Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : TP-LINK Wireless N Adapter Physical Address. . . . . . . . . : 00-25-86-DF-C6-89 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 192.168.1.7(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : 09 April 2010 23:09:45 Lease Expires . . . . . . . . . . : 10 April 2010 23:09:45 Default Gateway . . . . . . . . . : 192.168.1.1 DHCP Server . . . . . . . . . . . : 192.168.1.1 DNS Servers . . . . . . . . . . . : 192.168.1.1 NetBIOS over Tcpip. . . . . . . . : Enabled Ethernet adapter Local Area Connection 2: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller #2 Physical Address. . . . . . . . . : E0-CB-4E-26-B9-84 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Ethernet adapter Local Area Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller Physical Address. . . . . . . . . : E0-CB-4E-26-BE-94 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Tunnel adapter isatap.{74D5C406-894E-4000-8DE7-6AAEBF7C8382}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Microsoft ISATAP Adapter #2 Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Tunnel adapter Teredo Tunneling Pseudo-Interface: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes IPv6 Address. . . . . . . . . . . : 2001:0:5ef5:73ba:881:20c1:3f57:fef8(Preferred) Link-local IPv6 Address . . . . . : fe80::881:20c1:3f57:fef8%14(Preferred) Default Gateway . . . . . . . . . : :: NetBIOS over Tcpip. . . . . . . . : Disabled

  Read the article

• OpenVPN - Windows 8 to Windows 2008 Server, not connecting

  - by niico

  I have followed this tutorial about setting up an OpenVPN Server on Windows Server - and a client on Windows (in this case Windows 8). The server appears to be running fine - but it is not connecting with this error: Mon Jul 22 19:09:04 2013 Warning: cannot open --log file: C:\Program Files\OpenVPN\log\my-laptop.log: Access is denied. (errno=5) Mon Jul 22 19:09:04 2013 OpenVPN 2.3.2 x86_64-w64-mingw32 [SSL (OpenSSL)] [LZO] [PKCS11] [eurephia] [IPv6] built on Jun 3 2013 Mon Jul 22 19:09:04 2013 MANAGEMENT: TCP Socket listening on [AF_INET]127.0.0.1:25340 Mon Jul 22 19:09:04 2013 Need hold release from management interface, waiting... Mon Jul 22 19:09:05 2013 MANAGEMENT: Client connected from [AF_INET]127.0.0.1:25340 Mon Jul 22 19:09:05 2013 MANAGEMENT: CMD 'state on' Mon Jul 22 19:09:05 2013 MANAGEMENT: CMD 'log all on' Mon Jul 22 19:09:05 2013 MANAGEMENT: CMD 'hold off' Mon Jul 22 19:09:05 2013 MANAGEMENT: CMD 'hold release' Mon Jul 22 19:09:05 2013 Socket Buffers: R=[65536->65536] S=[65536->65536] Mon Jul 22 19:09:05 2013 UDPv4 link local: [undef] Mon Jul 22 19:09:05 2013 UDPv4 link remote: [AF_INET]66.666.66.666:9999 Mon Jul 22 19:09:05 2013 MANAGEMENT: >STATE:1374494945,WAIT,,, Mon Jul 22 19:10:05 2013 TLS Error: TLS key negotiation failed to occur within 60 seconds (check your network connectivity) Mon Jul 22 19:10:05 2013 TLS Error: TLS handshake failed Mon Jul 22 19:10:05 2013 SIGUSR1[soft,tls-error] received, process restarting Mon Jul 22 19:10:05 2013 MANAGEMENT: >STATE:1374495005,RECONNECTING,tls-error,, Mon Jul 22 19:10:05 2013 Restart pause, 2 second(s) Note I have changed the IP and port no (it uses a non-standard port for security reasons). That port is open on the hardware firewall. The server logs are showing a connection attempt from my client: TLS: Initial packet from [AF_INET]118.68.xx.xx:65011, sid=081af4ed xxxxxxxx Mon Jul 22 14:19:15 2013 118.68.xx.xx:65011 TLS Error: TLS key negotiation failed to occur within 60 seconds (check your network connectivity) How can I problem solve this & find the problem? Thx Update - Client config file: ############################################## # Sample client-side OpenVPN 2.0 config file # # for connecting to multi-client server. # # # # This configuration can be used by multiple # # clients, however each client should have # # its own cert and key files. # # # # On Windows, you might want to rename this # # file so it has a .ovpn extension # ############################################## # Specify that we are a client and that we # will be pulling certain config file directives # from the server. client # Use the same setting as you are using on # the server. # On most systems, the VPN will not function # unless you partially or fully disable # the firewall for the TUN/TAP interface. ;dev tap dev tun # Windows needs the TAP-Win32 adapter name # from the Network Connections panel # if you have more than one. On XP SP2, # you may need to disable the firewall # for the TAP adapter. ;dev-node MyTap # Are we connecting to a TCP or # UDP server? Use the same setting as # on the server. ;proto tcp proto udp # The hostname/IP and port of the server. # You can have multiple remote entries # to load balance between the servers. remote 00.00.00.00 1194 ;remote 00.00.00.00 9999 ;remote my-server-2 1194 # Choose a random host from the remote # list for load-balancing. Otherwise # try hosts in the order specified. ;remote-random # Keep trying indefinitely to resolve the # host name of the OpenVPN server. Very useful # on machines which are not permanently connected # to the internet such as laptops. resolv-retry infinite # Most clients don't need to bind to # a specific local port number. nobind # Downgrade privileges after initialization (non-Windows only) ;user nobody ;group nobody # Try to preserve some state across restarts. persist-key persist-tun # If you are connecting through an # HTTP proxy to reach the actual OpenVPN # server, put the proxy server/IP and # port number here. See the man page # if your proxy server requires # authentication. ;http-proxy-retry # retry on connection failures ;http-proxy [proxy server] [proxy port #] # Wireless networks often produce a lot # of duplicate packets. Set this flag # to silence duplicate packet warnings. ;mute-replay-warnings # SSL/TLS parms. # See the server config file for more # description. It's best to use # a separate .crt/.key file pair # for each client. A single ca # file can be used for all clients. ca "C:\\Program Files\\OpenVPN\\config\\ca.crt" cert "C:\\Program Files\\OpenVPN\\config\\my-laptop.crt" key "C:\\Program Files\\OpenVPN\\config\\my-laptop.key" # Verify server certificate by checking # that the certicate has the nsCertType # field set to "server". This is an # important precaution to protect against # a potential attack discussed here: # http://openvpn.net/howto.html#mitm # # To use this feature, you will need to generate # your server certificates with the nsCertType # field set to "server". The build-key-server # script in the easy-rsa folder will do this. ns-cert-type server # If a tls-auth key is used on the server # then every client must also have the key. ;tls-auth ta.key 1 # Select a cryptographic cipher. # If the cipher option is used on the server # then you must also specify it here. ;cipher x # Enable compression on the VPN link. # Don't enable this unless it is also # enabled in the server config file. comp-lzo # Set log file verbosity. verb 3 # Silence repeating messages ;mute 20 Server config file: ################################################# # Sample OpenVPN 2.0 config file for # # multi-client server. # # # # This file is for the server side # # of a many-clients <-> one-server # # OpenVPN configuration. # # # # OpenVPN also supports # # single-machine <-> single-machine # # configurations (See the Examples page # # on the web site for more info). # # # # This config should work on Windows # # or Linux/BSD systems. Remember on # # Windows to quote pathnames and use # # double backslashes, e.g.: # # "C:\\Program Files\\OpenVPN\\config\\foo.key" # # # # Comments are preceded with '#' or ';' # ################################################# # Which local IP address should OpenVPN # listen on? (optional) ;local 00.00.00.00 # Which TCP/UDP port should OpenVPN listen on? # If you want to run multiple OpenVPN instances # on the same machine, use a different port # number for each one. You will need to # open up this port on your firewall. std 1194 port 1194 # TCP or UDP server? ;proto tcp proto udp # "dev tun" will create a routed IP tunnel, # "dev tap" will create an ethernet tunnel. # Use "dev tap0" if you are ethernet bridging # and have precreated a tap0 virtual interface # and bridged it with your ethernet interface. # If you want to control access policies # over the VPN, you must create firewall # rules for the the TUN/TAP interface. # On non-Windows systems, you can give # an explicit unit number, such as tun0. # On Windows, use "dev-node" for this. # On most systems, the VPN will not function # unless you partially or fully disable # the firewall for the TUN/TAP interface. ;dev tap dev tun # Windows needs the TAP-Win32 adapter name # from the Network Connections panel if you # have more than one. On XP SP2 or higher, # you may need to selectively disable the # Windows firewall for the TAP adapter. # Non-Windows systems usually don't need this. ;dev-node MyTap # SSL/TLS root certificate (ca), certificate # (cert), and private key (key). Each client # and the server must have their own cert and # key file. The server and all clients will # use the same ca file. # # See the "easy-rsa" directory for a series # of scripts for generating RSA certificates # and private keys. Remember to use # a unique Common Name for the server # and each of the client certificates. # # Any X509 key management system can be used. # OpenVPN can also use a PKCS #12 formatted key file # (see "pkcs12" directive in man page). ca "C:\\Program Files\\OpenVPN\\config\\ca.crt" cert "C:\\Program Files\\OpenVPN\\config\\server.crt" key "C:\\Program Files\\OpenVPN\\config\\server.key" # Diffie hellman parameters. # Generate your own with: # openssl dhparam -out dh1024.pem 1024 # Substitute 2048 for 1024 if you are using # 2048 bit keys. dh "C:\\Program Files\\OpenVPN\\config\\dh2048.pem" # Configure server mode and supply a VPN subnet # for OpenVPN to draw client addresses from. # The server will take 10.8.0.1 for itself, # the rest will be made available to clients. # Each client will be able to reach the server # on 10.8.0.1. Comment this line out if you are # ethernet bridging. See the man page for more info. server 10.8.0.0 255.255.255.0 # Maintain a record of client <-> virtual IP address # associations in this file. If OpenVPN goes down or # is restarted, reconnecting clients can be assigned # the same virtual IP address from the pool that was # previously assigned. ifconfig-pool-persist ipp.txt # Configure server mode for ethernet bridging. # You must first use your OS's bridging capability # to bridge the TAP interface with the ethernet # NIC interface. Then you must manually set the # IP/netmask on the bridge interface, here we # assume 10.8.0.4/255.255.255.0. Finally we # must set aside an IP range in this subnet # (start=10.8.0.50 end=10.8.0.100) to allocate # to connecting clients. Leave this line commented # out unless you are ethernet bridging. ;server-bridge 10.8.0.4 255.255.255.0 10.8.0.50 10.8.0.100 # Configure server mode for ethernet bridging # using a DHCP-proxy, where clients talk # to the OpenVPN server-side DHCP server # to receive their IP address allocation # and DNS server addresses. You must first use # your OS's bridging capability to bridge the TAP # interface with the ethernet NIC interface. # Note: this mode only works on clients (such as # Windows), where the client-side TAP adapter is # bound to a DHCP client. ;server-bridge # Push routes to the client to allow it # to reach other private subnets behind # the server. Remember that these # private subnets will also need # to know to route the OpenVPN client # address pool (10.8.0.0/255.255.255.0) # back to the OpenVPN server. ;push "route 192.168.10.0 255.255.255.0" ;push "route 192.168.20.0 255.255.255.0" # To assign specific IP addresses to specific # clients or if a connecting client has a private # subnet behind it that should also have VPN access, # use the subdirectory "ccd" for client-specific # configuration files (see man page for more info). # EXAMPLE: Suppose the client # having the certificate common name "Thelonious" # also has a small subnet behind his connecting # machine, such as 192.168.40.128/255.255.255.248. # First, uncomment out these lines: ;client-config-dir ccd ;route 192.168.40.128 255.255.255.248 # Then create a file ccd/Thelonious with this line: # iroute 192.168.40.128 255.255.255.248 # This will allow Thelonious' private subnet to # access the VPN. This example will only work # if you are routing, not bridging, i.e. you are # using "dev tun" and "server" directives. # EXAMPLE: Suppose you want to give # Thelonious a fixed VPN IP address of 10.9.0.1. # First uncomment out these lines: ;client-config-dir ccd ;route 10.9.0.0 255.255.255.252 # Then add this line to ccd/Thelonious: # ifconfig-push 10.9.0.1 10.9.0.2 # Suppose that you want to enable different # firewall access policies for different groups # of clients. There are two methods: # (1) Run multiple OpenVPN daemons, one for each # group, and firewall the TUN/TAP interface # for each group/daemon appropriately. # (2) (Advanced) Create a script to dynamically # modify the firewall in response to access # from different clients. See man # page for more info on learn-address script. ;learn-address ./script # If enabled, this directive will configure # all clients to redirect their default # network gateway through the VPN, causing # all IP traffic such as web browsing and # and DNS lookups to go through the VPN # (The OpenVPN server machine may need to NAT # or bridge the TUN/TAP interface to the internet # in order for this to work properly). ;push "redirect-gateway def1 bypass-dhcp" # Certain Windows-specific network settings # can be pushed to clients, such as DNS # or WINS server addresses. CAVEAT: # http://openvpn.net/faq.html#dhcpcaveats # The addresses below refer to the public # DNS servers provided by opendns.com. ;push "dhcp-option DNS 208.67.222.222" ;push "dhcp-option DNS 208.67.220.220" # Uncomment this directive to allow differenta # clients to be able to "see" each other. # By default, clients will only see the server. # To force clients to only see the server, you # will also need to appropriately firewall the # server's TUN/TAP interface. ;client-to-client # Uncomment this directive if multiple clients # might connect with the same certificate/key # files or common names. This is recommended # only for testing purposes. For production use, # each client should have its own certificate/key # pair. # # IF YOU HAVE NOT GENERATED INDIVIDUAL # CERTIFICATE/KEY PAIRS FOR EACH CLIENT, # EACH HAVING ITS OWN UNIQUE "COMMON NAME", # UNCOMMENT THIS LINE OUT. ;duplicate-cn # The keepalive directive causes ping-like # messages to be sent back and forth over # the link so that each side knows when # the other side has gone down. # Ping every 10 seconds, assume that remote # peer is down if no ping received during # a 120 second time period. keepalive 10 120 # For extra security beyond that provided # by SSL/TLS, create an "HMAC firewall" # to help block DoS attacks and UDP port flooding. # # Generate with: # openvpn --genkey --secret ta.key # # The server and each client must have # a copy of this key. # The second parameter should be '0' # on the server and '1' on the clients. ;tls-auth ta.key 0 # This file is secret # Select a cryptographic cipher. # This config item must be copied to # the client config file as well. ;cipher BF-CBC # Blowfish (default) ;cipher AES-128-CBC # AES ;cipher DES-EDE3-CBC # Triple-DES # Enable compression on the VPN link. # If you enable it here, you must also # enable it in the client config file. comp-lzo # The maximum number of concurrently connected # clients we want to allow. ;max-clients 100 # It's a good idea to reduce the OpenVPN # daemon's privileges after initialization. # # You can uncomment this out on # non-Windows systems. ;user nobody ;group nobody # The persist options will try to avoid # accessing certain resources on restart # that may no longer be accessible because # of the privilege downgrade. persist-key persist-tun # Output a short status file showing # current connections, truncated # and rewritten every minute. status openvpn-status.log # By default, log messages will go to the syslog (or # on Windows, if running as a service, they will go to # the "\Program Files\OpenVPN\log" directory). # Use log or log-append to override this default. # "log" will truncate the log file on OpenVPN startup, # while "log-append" will append to it. Use one # or the other (but not both). ;log openvpn.log ;log-append openvpn.log # Set the appropriate level of log # file verbosity. # # 0 is silent, except for fatal errors # 4 is reasonable for general usage # 5 and 6 can help to debug connection problems # 9 is extremely verbose verb 3 # Silence repeating messages. At most 20 # sequential messages of the same message # category will be output to the log. ;mute 20 I have changed IP's for security

  Read the article

• Windows Server 2008: specifying the default IP address when NIC has multiple addresses

  - by Cédric Boivin

  I have a Windows Server which has ~10 IP addresses statically bound. The problem is I don't know how to specify the default IP address. Sometimes when I assign a new address to the NIC, the default IP address changes with the last IP entered in the advanced IP configuration on the NIC. This has the effect (since I use NAT) that the outgoing public IP changes too. Even though this problem is currently on Windows Server 2008 How can you set the default IP address on a NIC when it has multiple IP addresses bound? There is more explication on my probleme. Here is the ipconfig DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 192.168.99.49(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.51(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.52(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.53(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.54(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.55(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.56(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.57(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.58(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.59(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.60(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.61(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.62(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.64(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.65(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.66(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.67(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.68(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.70(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.71(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.100(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.108(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.109(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.112(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.63(Duplicate) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.99.1 If i do a pathping there is the answer, the first up is the 99.49, also if my default ip is 99.100 Tracing route to www.l.google.com [72.14.204.99] over a maximum of 30 hops: 0 Machine [192.168.99.49] There is the routing table on the machine Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.99.1 192.168.99.49 261 10.10.10.0 255.255.255.0 On-link 10.10.10.10 261 10.10.10.10 255.255.255.255 On-link 10.10.10.10 261 10.10.10.255 255.255.255.255 On-link 10.10.10.10 261 192.168.99.0 255.255.255.0 On-link 192.168.99.49 261 192.168.99.49 255.255.255.255 On-link 192.168.99.49 261 192.168.99.51 255.255.255.255 On-link 192.168.99.49 261 192.168.99.52 255.255.255.255 On-link 192.168.99.49 261 192.168.99.53 255.255.255.255 On-link 192.168.99.49 261 192.168.99.54 255.255.255.255 On-link 192.168.99.49 261 192.168.99.55 255.255.255.255 On-link 192.168.99.49 261 192.168.99.56 255.255.255.255 On-link 192.168.99.49 261 192.168.99.57 255.255.255.255 On-link 192.168.99.49 261 192.168.99.58 255.255.255.255 On-link 192.168.99.49 261 192.168.99.59 255.255.255.255 On-link 192.168.99.49 261 192.168.99.60 255.255.255.255 On-link 192.168.99.49 261 192.168.99.61 255.255.255.255 On-link 192.168.99.49 261 192.168.99.62 255.255.255.255 On-link 192.168.99.49 261 192.168.99.64 255.255.255.255 On-link 192.168.99.49 261 192.168.99.65 255.255.255.255 On-link 192.168.99.49 261 192.168.99.66 255.255.255.255 On-link 192.168.99.49 261 192.168.99.67 255.255.255.255 On-link 192.168.99.49 261 192.168.99.68 255.255.255.255 On-link 192.168.99.49 261 192.168.99.70 255.255.255.255 On-link 192.168.99.49 261 192.168.99.71 255.255.255.255 On-link 192.168.99.49 261 192.168.99.100 255.255.255.255 On-link 192.168.99.49 261 192.168.99.108 255.255.255.255 On-link 192.168.99.49 261 192.168.99.109 255.255.255.255 On-link 192.168.99.49 261 192.168.99.112 255.255.255.255 On-link 192.168.99.49 261 192.168.99.255 255.255.255.255 On-link 192.168.99.49 261 224.0.0.0 240.0.0.0 On-link 192.168.99.49 261 224.0.0.0 240.0.0.0 On-link 10.10.10.10 261 255.255.255.255 255.255.255.255 On-link 192.168.99.49 261 255.255.255.255 255.255.255.255 On-link 10.10.10.10 261 How i can be sure the ip use in the image ( suppose to be the default ip address ) will be use by my server as the default address ?

  Read the article

• network is not available even when cisco vpn client is connected. wrong route?

  - by javapowered

  I'm using Vodafone 3G modem. I've disabled other network devices in the system (ethernet, wifi, wimax) turned off firewall and antivirus. cisco vpn client connects successfully but I still can not access computer 192.168.147.120 (as well as any other computer from network). Any suggestions are welcome as I don't know what to do. ipconfig /all and route print commands (translated to english): Microsoft Windows [Version 6.1.7601] (C) Microsoft Corporation (Microsoft Corp.), 2009. All rights reserved. C: \ Users \ Oleg> ipconfig / all IP Configuration for Windows The name of the computer. . . . . . . . . : OlegPC The primary DNS-suffix. . . . . . : Node Type. . . . . . . . . . . . . : Hybrid IP-routing is enabled. . . . : No WINS-proxy enabled. . . . . . . : No Ethernet adapter Local Area Connection 4: DNS-suffix for this connection. . . . . : Description. . . . . . . . . . . . . : Cisco Systems VPN Adapter Physical Address. . . . . . . . . 00-05-9A-3C-78-00 DHCP is enabled. . . . . . . . . . . : No Autoconfiguration Enabled. . . . . . : Yes Local IPv6-address channel. . . : Fe80:: c073: 41b2: 852f: eb87% 26 (Preferred) IPv4-address. . . . . . . . . . . . : 10.53.127.204 (Preferred) The subnet mask. . . . . . . . . . : 255.0.0.0 Default Gateway. . . . . . . . . : IAID DHCPv6. . . . . . . . . . . : 536872346 DUID the client DHCPv6. . . . . . . 00-01-00-01-14-6F-4C-8D-60-EB-69-85-10-2D DNS-servers. . . . . . . . . . . : Fec0: 0:0: ffff:: 1% 1 fec0: 0:0: ffff:: 2% 1 fec0: 0:0: ffff:: 3% 1 NetBios over TCP / IP. . . . . . . . : Disabled Adapter mobile broadband connection through a broadband adapter mobile communications: DNS-suffix for this connection. . . . . : Description. . . . . . . . . . . . . : Vodafone Mobile Broadband Network Adapter (Huawei) Physical Address. . . . . . . . . 58-2C-80-13-92-63 DHCP is enabled. . . . . . . . . . . : No Autoconfiguration Enabled. . . . . . : Yes IPv4-address. . . . . . . . . . . . : 10.229.227.77 (Preferred) The subnet mask. . . . . . . . . . : 255.255.255.252 Default Gateway. . . . . . . . . : 10.229.227.78 DNS-servers. . . . . . . . . . . : 163.121.128.134 212.103.160.18 NetBios over TCP / IP. . . . . . . . : Disabled Tunnel adapter isatap. {737FF02E-D473-4F91-840E-2A4DD293FC12}: State of the environment. . . . . . . . : DNS Suffix. DNS-suffix for this connection. . . . . : Description. . . . . . . . . . . . . : Adapter Microsoft ISATAP # 3 Physical Address. . . . . . . . . 00-00-00-00-00-00-00-E0 DHCP is enabled. . . . . . . . . . . : No Autoconfiguration Enabled. . . . . . : Yes Tunnel adapter isatap. {EF585226-5B07-4446-A5A4-CB1B8E4B13AC}: State of the environment. . . . . . . . : DNS Suffix. DNS-suffix for this connection. . . . . : Description. . . . . . . . . . . . . : Adapter Microsoft ISATAP # 4 Physical Address. . . . . . . . . 00-00-00-00-00-00-00-E0 DHCP is enabled. . . . . . . . . . . : No Autoconfiguration Enabled. . . . . . : Yes Tunnel adapter Teredo Tunneling Pseudo-Interface: DNS-suffix for this connection. . . . . : Description. . . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface Physical Address. . . . . . . . . 00-00-00-00-00-00-00-E0 DHCP is enabled. . . . . . . . . . . : No Autoconfiguration Enabled. . . . . . : Yes IPv6-address. . . . . . . . . . . . : 2001:0:4137:9 e76: ea: b77: f51a: 1cb2 (Basically d) Local IPv6-address channel. . . : Fe80:: ea: b77: f51a: 1cb2% 16 (Preferred) Default Gateway. . . . . . . . . ::: NetBios over TCP / IP. . . . . . . . : Disabled C: \ Users \ Oleg> route print ================================================== ========================= List of interfaces 26 ... 00 05 9a 3c 78 00 ...... Cisco Systems VPN Adapter 23 ... 58 2c 80 13 92 63 ...... Vodafone Mobile Broadband Network Adapter (Huawei) 1 ........................... Software Loopback Interface 1 19 ... 00 00 00 00 00 00 00 e0 Adapter Microsoft ISATAP # 3 20 ... 00 00 00 00 00 00 00 e0 Adapter Microsoft ISATAP # 4 16 ... 00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface ================================================== ========================= IPv4 Route Table ================================================== ========================= Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.229.227.78 10.229.227.77 296 10.0.0.0 255.0.0.0 On-link 10.53.127.204 286 10.6.93.21 255,255,255,255 10.0.0.1 10.53.127.204 100 10.13.50.12 255,255,255,255 10.0.0.1 10.53.127.204 100 10.53.8.0 255.255.252.0 10.0.0.1 10.53.127.204 100 10.53.127.204 255.255.255.255 On-link 10.53.127.204 286 10.53.128.0 255.255.248.0 10.0.0.1 10.53.127.204 100 10.53.148.0 255,255,255,240 10.0.0.1 10.53.127.204 100 10.53.148.16 255,255,255,240 10.0.0.1 10.53.127.204 100 10.229.227.76 255.255.255.252 On-link 10.229.227.77 296 10.229.227.77 255.255.255.255 On-link 10.229.227.77 296 10.229.227.79 255.255.255.255 On-link 10.229.227.77 296 10.255.255.255 255.255.255.255 On-link 10.53.127.204 286 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.147.0 255,255,255,240 10.0.0.1 10.53.127.204 100 192.168.147.96 255,255,255,240 10.0.0.1 10.53.127.204 100 192,168,147,112 255,255,255,240 10.0.0.1 10.53.127.204 100 192,168,147,128 255,255,255,240 10.0.0.1 10.53.127.204 100 192,168,147,144 255,255,255,240 10.0.0.1 10.53.127.204 100 192,168,147,224 255,255,255,240 10.0.0.1 10.53.127.204 100 192.168.214.0 255.255.255.0 10.0.0.1 10.53.127.204 100 192.168.215.0 255.255.255.0 10.0.0.1 10.53.127.204 100 194.247.133.19 255,255,255,255 10.0.0.1 10.53.127.204 100 213,247,231,194 255,255,255,255 10.229.227.78 10.229.227.77 100 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 10.229.227.77 296 224.0.0.0 240.0.0.0 On-link 10.53.127.204 286 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 10.229.227.77 296 255.255.255.255 255.255.255.255 On-link 10.53.127.204 286 ================================================== ========================= Persistent Routes: None IPv6 Route Table ================================================== ========================= Active Routes: If Metric Network Destination Gateway 16 58:: / 0 On-link 1306:: 1 / 128 On-link 16 58 2001:: / 32 On-link 16 306 2001: 0:4137:9 e76: ea: b77: f51a: 1cb2/128 On-link 16 306 fe80:: / 64 On-link 26 286 fe80:: / 64 On-link 16 306 fe80:: ea: b77: f51a: 1cb2/128 On-link 26 286 fe80:: c073: 41b2: 852f: eb87/128 On-link 1306 ff00:: / 8 On-link 16 306 ff00:: / 8 On-link 26 286 ff00:: / 8 On-link ================================================== ========================= Persistent Routes: None C: \ Users \ Oleg>

  Read the article

• VPN Connection causes DNS to use wrong DNS server

  - by Bryan

  I have a Windows 7 PC on our company network (which is a member of our Active Directory). Everything works fine until I open a VPN connection to a customer's site. When I do connect, I lose network access to shares on the network, including directories such as 'Application Data' that we have a folder redirection policy for. As you can imagine, this makes working on the PC very difficult, as desktop shortcuts stop working, software stops working properly due to having 'Application Data' pulled from under it. Our network is routed (10.58.5.0/24), with other local subnets existing within the scope of 10.58.0.0/16. The remote network is on 192.168.0.0/24. I've tracked the issue down to being DNS related. As soon as I open the VPN tunnel, all my DNS traffic goes via the remote network, which explains the loss of local resources, but my question is, how can I force local DNS queries to go to our local DNS servers rather than our customers? The output of ipconfig /all when not connected to the VPN is below: Windows IP Configuration Host Name . . . . . . . . . . . . : 7k5xy4j Primary Dns Suffix . . . . . . . : mydomain.local Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : mydomain.local Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : mydomain.local Description . . . . . . . . . . . : Broadcom NetLink (TM) Gigabit Ethernet Physical Address. . . . . . . . . : F0-4D-A2-DB-3B-CA DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::9457:c5e0:6f10:b298%10(Preferred) IPv4 Address. . . . . . . . . . . : 10.58.5.89(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : 31 January 2012 15:55:47 Lease Expires . . . . . . . . . . : 10 February 2012 10:11:30 Default Gateway . . . . . . . . . : 10.58.5.1 DHCP Server . . . . . . . . . . . : 10.58.3.32 DHCPv6 IAID . . . . . . . . . . . : 250629538 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-14-AC-76-2D-F0-4D-A2-DB-3B-CA DNS Servers . . . . . . . . . . . : 10.58.3.32 10.58.3.33 NetBIOS over Tcpip. . . . . . . . : Enabled This is the output of the same command with the VPN tunnel connected: Windows IP Configuration Host Name . . . . . . . . . . . . : 7k5xy4j Primary Dns Suffix . . . . . . . : mydomain.local Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : mydomain.local PPP adapter Customer Domain: Connection-specific DNS Suffix . : customerdomain.com Description . . . . . . . . . . . : CustomerDomain Physical Address. . . . . . . . . : DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 192.168.0.85(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.255 Default Gateway . . . . . . . . . : DNS Servers . . . . . . . . . . . : 192.168.0.16 192.168.0.17 Primary WINS Server . . . . . . . : 192.168.0.17 NetBIOS over Tcpip. . . . . . . . : Disabled Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : mydomain.local Description . . . . . . . . . . . : Broadcom NetLink (TM) Gigabit Ethernet Physical Address. . . . . . . . . : F0-4D-A2-DB-3B-CA DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::9457:c5e0:6f10:b298%10(Preferred) IPv4 Address. . . . . . . . . . . : 10.58.5.89(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : 31 January 2012 15:55:47 Lease Expires . . . . . . . . . . : 10 February 2012 10:11:30 Default Gateway . . . . . . . . . : 10.58.5.1 DHCP Server . . . . . . . . . . . : 10.58.3.32 DHCPv6 IAID . . . . . . . . . . . : 250629538 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-14-AC-76-2D-F0-4D-A2-DB-3B-CA DNS Servers . . . . . . . . . . . : 10.58.3.32 10.58.3.33 NetBIOS over Tcpip. . . . . . . . : Enabled Routing table Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.58.5.1 10.58.5.89 20 10.58.5.0 255.255.255.0 On-link 10.58.5.89 276 10.58.5.89 255.255.255.255 On-link 10.58.5.89 276 10.58.5.255 255.255.255.255 On-link 10.58.5.89 276 91.194.153.42 255.255.255.255 10.58.5.1 10.58.5.89 21 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.0.0 255.255.255.0 192.168.0.95 192.168.0.85 21 192.168.0.85 255.255.255.255 On-link 192.168.0.85 276 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 10.58.5.89 276 224.0.0.0 240.0.0.0 On-link 192.168.0.85 276 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 10.58.5.89 276 255.255.255.255 255.255.255.255 On-link 192.168.0.85 276 The binding order for the interfaces is as follows: I've not configured the VPN tunnel to use the default gateway at the remote end, and network comms to nodes on both networks are fine. (i.e. I can ping any node on our network or the remote network). I've modified the PPTP connection properties to use the DNS servers 10.58.3.32 followed by 192.168.0.16, yet the query still goes to 192.168.0.16. Edit: The local resources that disappear are hosted on domain DFS roots, which might (or might not) be relevant.

  Read the article

< Previous Page | 17 18 19 20 21 22  | Next Page >