Search Results

Search found 9365 results on 375 pages for '13 04'.

Page 210/375 | < Previous Page | 206 207 208 209 210 211 212 213 214 215 216 217  | Next Page >

• Why can't I boot from portable HD?

  - by user11239

  I've been trying to get Ubuntu 10.04-LTS 32-bit desktop installed onto a 250GB FreeAgent Go drive from Seagate. I've been able to install onto a USB flash drive and boot successfully from this. I have installed Ubuntu onto the jump drive using Universal USB Installer, and this was a total success in terms of getting Ubuntu to run off a flash drive. I was unable to accomplish this with the portable HDD. I then, following instructions, attempted to install the OS onto the HDD once booted up from the flash drive. After installing the OS on the HDD, the computer would simply not load the OS when the HDD medium was selected for booting from. However, as there is no System-> Preferences-> Removable Drives and Media I could not complete this step. Is this vital? How do I do this under Ubuntu 10.04? I have formmated the MBR on the HDD and repeated the above, still with no success. I have also browsed some forums that mention there may be something related to spin-up speeds, but nothing explained in detail the issue or how to solve it, and I'm not familiar enough with system booting to understand if this could be an issue. Basically, what I'm trying to do is get Ubuntu to boot off the HDD, I've attempted several things, and the result is, after selecting the HDD from BIOS, the OS never starts booting (after waiting upwards of ten minutes). I just have a white cursor blinking. I can always get it to boot from the jump drive. Related question

  Read the article

• How do I connect to a wireless network?

  - by Keith Groben

  I just installed 10.10 x64 and cannot even find my wireless network let alone connect to it. I've searched all over SE and Ubuntu forums and cannot find out how to do this simple thing. Can some one please give me the answer? It is plugged in right now and is 100% updated. It is a Desktop with wireless card. 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no Here's the output: *-network DISABLED description: Wireless interface product: RT2860 vendor: RaLink physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 00 serial: 70:1a:04:f4:de:e9 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rt2800pci driverversion=2.6.35-27-generic firmware=N/A latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:fcff0000-fcffffff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 03 serial: 00:23:54:fd:c2:32 size: 100MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.1.14 latency=0 link=yes multicast=yes port=MII speed=100MB/s resources: irq:44 ioport:d800(size=256) memory:fceff000-fcefffff memory:ddffc000-ddffffff memory:fcec0000-fcedffff === Update === I have discovered that this is a know issue with the rt2860. I have been following step by step the instructions found here: http://www.ctbarker.info/2010/05/ubuntu-1004-wireless-chipsets-and-wpa.html I decided to stat over because I was getting stuck on step 5: 'sudo rmmod rt2860sta' is was giving me this problem: 'ERROR: Module rt2860sta does not exist in /proc/modules' Since I started over I cannot even get past step 5 'sudo make' I get this: 'make: * No targets specified and no makefile found. Stop.' I am lost. Any help would be appreciated.

  Read the article

• Access a PLESK website before propagation?

  - by RCNeil

  My web host uses Plesk and I want to know if there is anyway to access and view a website (with PHP and other processes being functional) without propagation of the domain name? I have found countless forums on this but they are all pretty old (circa 01-04) and involve either tricking your localhost or SSH commands and some even result in terrible security risks. I would like to access a web page directory through a browser and see it's contents while having the PHP processes carry out... before I propagate it's potential domain name. People claim this is pointless but during a site migration why on earth would you not test a site before propagating it? I'm looking for something similar to what cPanel offers i.e. http://IP.ADDRESS./~mydomain.com The only solution I could think of is storing the site in a new directory of an already functional site and then setting up databases and testing the site once it's complete. Once tested and working I should be easily be able to migrate the files to the "new" domain name's root directory and just setup a new databases and then propagate the domain name. I can't believe that Plesk V10+ still does not have a site preview method that includes PHP, JS, and Flash ability.

  Read the article

• Bootable dvd installs ubuntu in one computer but not in other...Why? [closed]

  - by SAM

  Possible Duplicate: My computer boots to a black screen, what options do I have to fix it? I have 2 computers, Windows 7 Intel. On one computer Ubuntu boot-able DVD (AMD 64) works properly. But on other computer the same DVD boots OK but when clicked on "Install Ubuntu" a blank screen with blinking cursor(_) appears and it continues just blinking forever. What problem can be there in computer 2? Can it be DVD reader's problem? (Both computers have LG DVD RW) Can there be any problem in DVD? Computer 1 specs: Pentium D 3 GHz Windows 7 32-bit not a 64bit-capable processor still Ubuntu 64bit trial/installer runs... Computer 2 specs: Core i7 2700k Windows 7 32-bit nvidia gtx 560 graphicsCard ...BIG BOSS... still can't run the setup/trial/disk-check/memory-test ?!?!? Is it the problem of graphics card ?!? I also tried burning other dvd which has the same behavour.... AND yes the dvd name is: ubuntu-12.04.1-dvd-amd64.iso Any help is appreciated.

  Read the article

• Ubuntu 12.04 still slow at mounting internal filesystem

  - by Matthew Goson

  I'm using Toshiba laptop with this configuration: - CPU: Core i5, 2.4GHz - RAM: 4GB - Graphics card: Intel - Hard disk: 500GB SATA I installed Ubuntu 12.04 64bit and got the same issue with this guy Very slow boot due to mounting filesytem, I tried all suggestions there but the slow boot issue still here. Here's a part of my dmesg: [ 2.041015] usbhid: USB HID core driver [ 2.101378] usb 1-1.6: new full-speed USB device number 5 using ehci_hcd [ 2.137980] atl1c 0000:04:00.0: version 1.0.1.0-NAPI [ 2.779080] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null) [ 22.822597] udevd[381]: starting version 175 [ 22.837954] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 22.850837] lp: driver loaded but no devices found [ 23.003822] Adding 7079096k swap on /dev/sda7. Priority:-1 extents:1 across:7079096k [ 23.407915] mei: module is from the staging directory, the quality is unknown, you have been warned. [ 23.408153] mei 0000:00:16.0: PCI->APIC IRQ transform: INT A -> IRQ 16 [ 23.408160] mei 0000:00:16.0: setting latency timer to 64 [ 23.408211] mei 0000:00:16.0: irq 44 for MSI/MSI-X [ 23.433196] [drm] Initialized drm 1.1.0 20060810 Additional information: my sda1 is a primary NTFS partition, sda2 is a primary ext4 partition which I installed Ubuntu onto. Other partitions are inside an extended partition.

  Read the article

• Recover Lost data/partition

  - by Kaleido

  This is what happened: I was running 12.04.1 and wanted to install 12.10. upgrade, but a fresh install. When setting up my computer I anticipated for this by dividing my 640GB HD in following partitions: 1. 60 GB for Ubuntu, boot 2. 576 GB for data, mountpoint /home 3. swap, 4GB The idea was to manually select the correct partition in the installer but I got distracted for a moment and selected the wrong option. Result: The installer started repartitioning the entire HD. When I noticed this I interrupted the installer, but upon reboot it was clear that I was too late, no OS to boot to. I booted from a Gparted Live CD to see if I could recover the data on my previous /home-partition, but it's gone. Is there any way to recover the lost data? I searched around and read alot about Testdisk, but in all the tutorials I've seen, the set-up has been much easier than what I'm facing. I've not only lost my partition table, it's been replaced. Thanks in advance for any ideas that might help! If extra info is needed, please specify and I will do my best to provide.

  Read the article

• HP DV6 connects but no internet

  - by Frank Barcenas

  I have a Hewlett Packard DV6. I connected to the access point. I receive an IP address/default gateway/DNS,etc(DHCP). I cannot ping my gateway. DNS lookups fails. There is just no connectivity. My driver is listed as being IWLWIFI. An lspci shows my card to be a Realtek RTL8101E/RTL8102E. I can't ping myself from another computer. eth0 Link encap:Ethernet HWaddr c8:0a:a9:0c:a7:45 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:41 Base address:0xe000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:561 errors:0 dropped:0 overruns:0 frame:0 TX packets:561 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:42164 (42.1 KB) TX bytes:42164 (42.1 KB) wlan0 Link encap:Ethernet HWaddr 00:26:c7:04:97:c0 inet addr:192.168.1.109 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::226:c7ff:fe04:97c0/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:71 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2035 (2.0 KB) TX bytes:12371 (12.3 KB)

  Read the article

• Another hibernation question

  - by GeekOfTheWeek

  I installed Ubuntu on my Windows 7 Sager laptop using Wubi. Hibernate (i.e. suspend to disc) is not an option from the power icon, only suspend, shutdown, etc. Hibernate is also not an option from my battery/lid close options. I understand that hibernation is disabled by default in Ubuntu 12.04. I tried running pm-hibernate but I get the following message: Looking for splash system... none s2disk: Snapshotting system and then the computer just hangs with a black screen. According to the documentation here if this fails then I can't enable hibernate but it offers no help in making pm-hibernate succeed. Could swap be my problem? It looks like I have very small swap: user@ubuntu:~$ cat /proc/swaps Filename Type Size Used Priority /host/ubuntu/disks/swap.disk file 262140 0 -1 The advice on SwapFaq is only for the author's set up (e.g. I don't have an Ubuntu install disk since I used Wubi) and he says that 'INFO: This will not work for 12.04, resume from hibernate work differently in 12.04.' Any advice? I really need to get hibernate working to use my laptop as a, er, laptop. Thanks

  Read the article

• cannot boot ubuntu 13.10 with my usb, Can i change the kernal on my laptop to run it?

  - by Carlos Dunick

  Currently i am running 12.04 and looking for an upgrade to 13.10 I first tried a bootable 64bit usb and failed. With the message saying "Kernal requires an x86-64 CPU but only detected an I686 CPU Unable to boot please use a kernal appropriate for your CPU" then tried 32bit and same message came up. Is this due to my laptop simply being to slow? or can/should i change the kernal somehow? Acer Aspire 5710z Intel Pentium dual core processor, 1.73Ghz, 533 MHz FSB, 1 MB L2 cache. 2GB DDR2 lspci 00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation NM10/ICH7 Family High Definition Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation NM10/ICH7 Family PCI Express Port 1 (rev 02) 00:1c.2 PCI bridge: Intel Corporation NM10/ICH7 Family PCI Express Port 3 (rev 02) 00:1c.3 PCI bridge: Intel Corporation NM10/ICH7 Family PCI Express Port 4 (rev 02) 00:1d.0 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #1 (rev 02) 00:1d.1 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #2 (rev 02) 00:1d.2 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #3 (rev 02) 00:1d.3 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #4 (rev 02) 00:1d.7 USB controller: Intel Corporation NM10/ICH7 Family USB2 EHCI Controller (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02) 00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 02) 00:1f.2 SATA controller: Intel Corporation 82801GBM/GHM (ICH7-M Family) SATA Controller [AHCI mode] (rev 02) 00:1f.3 SMBus: Intel Corporation NM10/ICH7 Family SMBus Controller (rev 02) 04:00.0 Ethernet controller: Broadcom Corporation NetLink BCM5787M Gigabit Ethernet PCI Express (rev 02) 05:00.0 Network controller: Broadcom Corporation BCM4311 802.11b/g WLAN (rev 01) 06:00.0 FLASH memory: ENE Technology Inc ENE PCI Memory Stick Card Reader Controller 06:00.1 SD Host controller: ENE Technology Inc ENE PCI SmartMedia / xD Card Reader Controller 06:00.2 FLASH memory: ENE Technology Inc Memory Stick Card Reader Controller 06:00.3 FLASH memory: ENE Technology Inc ENE PCI Secure Digital / MMC Card Reader Controller

  Read the article

• Kubuntu not showing eth0

  - by Laurbert515

  I just installed Kubuntu 12.04.2 and do not have an internet connection. I also cannot access the Desktop and only have the terminal. When I enter xlcock I get Error: Can't open display:. I believe this is because I do not have the correct drivers and need to download them ... using the internet which I can't access. So here's what's going on ... ifconfig gives: lo Link ecap: Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:16 errors:0 dropped:0 overrruns:0 frame:0 TX packets:16 errors:0 dropped:0 overrruns:0 frame:0 collisions:0 txqueuelen:0 RX bytes:1296 (1.2 KB) TX bytes:1296 (1.2 KB) wlan0 Link encap: Ethernet HWaddr 68:17:29:58:49:4a UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:16 errors:0 dropped:0 overrruns:0 frame:0 TX packets:16 errors:0 dropped:0 overrruns:0 frame:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lspci -nnk gives: 07:00.0 Network Controller [0280] Intel Corporation Centrino Wireless-N 2230 [8086:0887] (rev c4) Subsystem: Intel Coporation Centrino Wireless-N 2230 BGN [8086:4062] Kernel driver in use: iwlwifi Kernel modules: iwlwifi 0d:00.0 Ethernet Controller [0200]: Atheros Communications Inc. AR8161 Gigabit Ethernet [1969:1091] (rev 10) Subsystem: Toshiba America Info Systems Device [1179:fa77] I believe this means that it is using the ethernet connection but thinks it is a wireless connection. sudo lshw -class network gives: *-network description: Wireless interface product: Centrino Wireless=N 2230 ... *network UNCLAIMED description: Ethernet controller product: AR8161 Gigabit Ethernet I want to get the internet working so I can fix the GPU driver, etc. but I can't seem to get it working even though I have my ethernet cable plugged in (and I'm sure it is working).

  Read the article

• Problems to boot, Ubuntu entry does not work anymore

  - by user104108

  A few months I decided to install Ubuntu 12.04 on my PC alongside with my Windows 7 partition. In order to do that and avoid any mistake, I followed these steps: http://www.linuxbsdos.com/2012/05/17/how-to-dual-boot-ubuntu-12-04-and-windows-7/2/ Everything was going well until I decided to update to the 12.10 realese. I don't know what happened, but after I updated my Ubuntu, it stoped working, it didn't even launched, when I turned on my pc and choose to run "Ubuntu 12.04" on the Grub Screen, a weird messaged appeared. Well, so I decided to install the Ubuntu 12.10 and forget about the 12.04 partition, no problem. I erased the partitions used for the Ubuntu 12.04 with EaseUS partition Manager. However, when I start my PC, there is still the option of "Ubuntu 12.04" to chose, is that bad? And what about now, can I use the Windows Installer of Ubuntu ( http://www.ubuntu.com/download/help/install-ubuntu-with-windows ) to install the Ubuntu 12.10 ? What should I do to have Ubuntu 12.10 and Windows 7 in dual boot again? Thanks; Thales.

  Read the article

• Grub menu not waiting despite of GRUB_TIMEOUT=10

  - by Optimus

  I have Ubuntu 12.04 installed along side of windows 7. The grub menu doesn't seem obey GRUB_TIMEOUT=10, I see the grub menu there for a split second and it immediately defaults to the first option. Grub menu worked fine when I first installed ubuntu. I am not able to pinpoint what exactly broke it(maybe some update?). I did resize my ubuntu partition using gparted but am not sure if that is what caused it. here are my settings from etc/default/grub GRUB_DEFAULT=0 #GRUB_HIDDEN_TIMEOUT=0 #GRUB_HIDDEN_TIMEOUT_QUIET=true GRUB_TIMEOUT=10 GRUB_DISTRIBUTOR=`lsb_release -i -s 2> /dev/null || echo Debian` GRUB_CMDLINE_LINUX_DEFAULT="quiet splash" GRUB_CMDLINE_LINUX="" How do I fix this? Edit: As suggested by 'kamil' this is what I have tried so far with no luck - 1) hold the shift key while booting 2) sudo gedit /etc/default/grub edit GRUB_TIMEOUT to `GRUB_TIMEOUT=10` sudo update-grub 3) sudo gedit /etc/default/grub edit GRUB_TIMEOUT to `GRUB_TIMEOUT=10` sudo update-grub2 4) at the end of your /etc/grub.d/00_header file, comment out the if condition except for the regular set timeout line like this: #if [ \${recordfail} = 1 ]; then # set timeout=-1 #else set timeout=${GRUB_TIMEOUT} #fi then sudo update-grub and sudo update-grub2 5) install boot repair sudo add-apt-repository ppa:yannubuntu/boot-repair sudo apt-get update sudo apt-get install -y boot-repair boot-repair boot-repair output - Boot successfully repaired. ... The boot files of [The OS now in use - Ubuntu 12.04.1 LTS] are far from the start of the disk. Your BIOS may not detect them. You may want to retry after creating a /boot partition (EXT4, 200MB, start of the disk). This can be performed via tools such as gParted. Then select this partition via the [Separate /boot partition:] option of [Boot Repair]. (https://help.ubuntu.com/community/BootPartition) http://paste.ubuntu.com/1220468/ - here is the full boot-repair data Could grub files not being at the start of the disk create such issues?

  Read the article

• M-Audio Delta 1010LT on 12.04

  - by user74039

  I have 12.04 64bit installed, my soundcard is a Delta 1010LT, it seems to be partially detected, I've been following steps here: https://help.ubuntu.com/community/SoundTroubleshooting/ lspci -v | grep -A7 -i "audio" shows this: 04:07.0 Multimedia audio controller: VIA Technologies Inc. ICE1712 [Envy24] PCI Multi-Channel I/O Controller (rev 02) Subsystem: VIA Technologies Inc. M-Audio Delta 1010LT Flags: bus master, medium devsel, latency 64, IRQ 22 I/O ports at ec00 [size=32] I/O ports at e880 [size=16] I/O ports at e800 [size=16] I/O ports at e480 [size=64] Capabilities: <access denied> Kernel driver in use: snd_ice1712 aplay shows this: **** List of PLAYBACK Hardware Devices **** card 0: M1010LT [M Audio Delta 1010LT], device 0: ICE1712 multi [ICE1712 multi] Subdevices: 1/1 Subdevice #0: subdevice #0 In the sound settings on the desktop all I see is the ICE1712 S/PDIF, which I don't use, I want to use the individual outputs on the card, I'm not so bothered about inputs, I just want the playback for now. If I open alsamixer in the console, I see all of the output and input channels, i've raised the volume on them but I don't get anything in the sound settings on the desktop and when I play any sound, I hear nothing. Can someone help?

  Read the article

• maxItemsInObjectGraph limit required to be changed for server and client

  - by Michael Freidgeim

  We have a wcf service, that expects to return a huge XML data. It worked ok in testing, but in production it failed with error  "Maximum number of items that can be serialized or deserialized in an object graph is '65536'. Change the object graph or increase the MaxItemsInObjectGraph quota."The MSDN article about   dataContractSerializer xml configuration  element  correctly  describes maxItemsInObjectGraph attribute default as 65536, but documentation for of the DataContractSerializer.MaxItemsInObjectGraph property and DataContractJsonSerializer.MaxItemsInObjectGraph Property are talking about Int32.MaxValue, which causes confusion, in particular because Google shows properties articles before configuration articles.When we changed the value in WCF service configuration, it didn't help, because the similar change must be ALSO done on client.There are similar posts:http://stackoverflow.com/questions/6298209/how-to-fix-maxitemsinobjectgraph-error/6298356#6298356You need to set the MaxItemsInObjectGraph on the dataContractSerializer using a behavior on both the client and service. See  for an example.http://devlicio.us/blogs/derik_whittaker/archive/2010/05/04/setting-maxitemsinobjectgraph-for-wcf-there-has-to-be-a-better-way.aspxhttp://stackoverflow.com/questions/2325321/maxitemsinobjectgraph-ignored/4455209#4455209 I had forgot to place this setting in my client app.config file.http://stackoverflow.com/questions/9191167/maximum-number-of-items-that-can-be-serialized-or-deserialized-in-an-object-graphttp://stackoverflow.com/questions/5867304/datacontractjsonserializer-and-maxitemsinobjectgraph?rq=1 -It seems that DataContractJsonSerializer.MaxItemsInObjectGraph has actual default 65536, because there is no configuration for JSON serializer, but  it complains about the limit.I believe that MS should clarify the properties documentation re default limit and make more specific error messages to distinguish server side and client side errors.Note, that as a workaround it's possible to use commonBehaviors section which can be defined only in machine.config:<commonBehaviors> <behaviors> <endpointBehaviors> <dataContractSerializer maxItemsInObjectGraph="..." /> </endpointBehaviors> </behaviors></commonBehaviors>v

  Read the article

• How to connect MTS MBlaze

  - by murali_ma

  i have installed ubuntu 11.04 inside the windows xp. i have MTS Mblaze USB Modem. (my service provider is MTS MBlaze,india) i want to use Mblaze into ubuntu so that i did the following steps for make connecting the device. from the task bar->edit connections->mobile broadband->choose country->mts mblaze and ok i give username and password ([email protected] and password MTS. ok now i enable mobile broadband , MTS MBlaze connection1(connection name) from task bar. steps followed from "http://randomshandom.wordpress.com/2010/12/20/how-to-connect-mts-mblaze-device-in-ubuntu-10-10-11-04/#more-3" for the first time it successfully connected and browse the internet. after i restart the system i connect it. it does not connected. it shows Modem network disconnected. i accessed many times and delete the connection and recreated but i does not help me. if i try to connect device i think it the search the network, i saw the wave signal. img Image for showing problem:

  Read the article

• Is the addition of a duration to a date-time defined in ISO 8601?

  - by Benjamin

  I've writing a date-time library, and need to implement the addition of a duration to a date-time. If I add a 1 month duration: P1M to the 31st March 2012: 2012-03-31, does the standard define what the result is? Because the resulting date (31st April) does not exist, there are at least two options: Fall back to the last day of the resulting month. This is the approach currently taken by the ThreeTen API, the (alpha) reference implementation of JSR-310: ZonedDateTime date = ZonedDateTime.parse("2012-03-31T00:00:00Z"); Period duration = Period.parse("P1M"); System.out.println(date.plus(duration).toString()); // 2012-04-30T00:00Z Carry the extra day to the next month. This is the approach taken by the DateTime class in PHP: $date = new DateTime('2012-03-31T00:00:00Z'); $duration = new DateInterval('P1M'); echo $date->add($duration)->format('c'); // 2012-05-01T00:00:00+00:00 I'm surprised that two date-time libraries contradict on this point, so I'm wondering whether the standard defines the result of this operation?

  Read the article

• Ubuntu 12.04 wireless disabled even though the direct connectin (thru modem) is working fine

  - by user90841

  Need help with my newly installed Ubuntu 12.04 system (dual booting along with Win 7), even thoguh I can use internet using the modem and directly plugging it, the wireless network is disabled and it says firmware missing. I tried the following options: 1) checking to see if the wireless is disabled using the hot keys (F2 or Ctrl+F2, Fn + F2 keys), the wireless is working fine in Win 7 but not in Ubuntu. 2) I am able directly plug the laptop with the modem and able connect to Internet using Ubuntu. 3) From the top right hand menu bar, te Wireless networks options say "device not ready (firmware missing) and the Enable Wireless checkbox is checked. 4) tried the command "rfkill list" , it shows all are NOT blocked. 0: phy0: Wireless LAN soft blocked:no Hard blocked: no 1: dell-wifi: Wireless LAN soft blocked:no Hard blocked: no 2: dell-bluetooth: BlueTooth soft blocked:no Hard blocked: no 3: hci0 Bluetooth soft blocked:no Hard blocked: no 5) ifconfig command shows eth0 and lo (lcoalhost) up and running but the wlan0 option is not available to show unless I type ifconfig -a, when it shows wlan0 but its down. 6) The command lspci -vvnn | grep 14e4 shows 04:00.0 network Controller [0280]: Broadcom Corp BCM4312 802.11b/g LP-PHY [14e4:4315] {rev 01) 08:00.0 Ethernet Controller [0200]: Broadcom Corp Netlink BCM5784M Gigabit Ethernet PCIe [1434:1698] {rev 10) 7) The file /var/lib/NetworkManager/NetworkManager.state shows all options are true (networking enabled, wireless enabled, wwlanenabled and wimaxenabled all options are set to true). 8) 'additional drivers' in your Dash and/or Preferences do not bring up anything at all. 9) output for lshw -C network shows *-network DISABLED description : Wireless interface physical id: 4 logical name: wlan0 serial: 78:e4_00"43:b6:ab capabilities: ethernet physical wireless Configuration: broadcast=yes driver=b43 driverversion=3.2.0.29-generic-pae firmware=N/A link=no multicast= yes wireless=IEEE 802.11bg

  Read the article

• Wifi interface changes name seemingly at random

  - by ray_voelker

  I'm currently having some issues getting a wireless interface to work continuously under an install of Ubuntu 12.04.1 LTS. Some of the issues I'm experiencing include Connection will drop out after some time after it has initially worked. Interface will be a different name after a reboot. For example, wlan0 will become wlan4 when using the ifconfig -a command. Ubuntu will take a long time to boot, looking for network adapters. The purpose of this build is to function as a web kiosk in a library. The computer is supposed to boot up into a web browser, and allow for browsing of the catalog. For some reason this interface does not appear to be working as it should. Are there any explanations for some of these problems I'm having, and perhaps some solutions? The wireless card appears as this after doing an lspci ... Ralink corp. RT2561/RT61 802.11g PCI In the /etc/network/interfaces file I have the following configuration for the interface. auto wlan0 iface wlan0 inet dhcp wireless-essid UDwireless wireless-mode Managed Thanks in advance for help on this.

  Read the article

• How do I configure an Intel HD Graphics 4000?

  - by derabbink

  First off, please note that last night I already posted this question to a launchpad mailing list, so this could be considered a cross post. However, I think this is a better place to ask the same question The question: How can I configure my Ubuntu 12.04, with upgraded kernel (3.6), to use the Intel HD Graphics 4000 adapter? (Intel HD 4000 is the standard of 3rd gen Intel Core i7 (Ivy Bridge) graphics adapter) Some output: $ glxinfo name of display: :0 X Error of failed request: BadRequest (invalid request code or no such operation) Major opcode of failed request: 154 (GLX) Minor opcode of failed request: 19 (X_GLXQueryServerString) Serial number of failed request: 12 Current serial number in output stream: 12 $ cat /etc/X11/xorg.conf this is probably the farthest from what it should be Section "Screen" Identifier "Default Screen" DefaultDepth 24 EndSection Section "Module" Load "glx" EndSection $ lspci I only listed the line I think are relevant. If you want more info in order to help me, please comment :) 00:02.0 VGA compatible controller: Intel Corporation Ivy Bridge Graphics Controller (rev 09) 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) 16:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI Whistler XT [AMD Radeon HD 6700M Series] 16:00.1 Audio device: Advanced Micro Devices [AMD] nee ATI Turks HDMI Audio [Radeon HD 6000 Series]

  Read the article

• How do I add a boot from cd option to yaboot?

  - by Sergiu

  So I'm dual-booting Ubuntu 12.04.1 on my iMac G5 powepc alongside Mac OS X and I want to add a boot cd option to yaboot because I'm trying to boot a scratched Mac OS X installation DVD that takes a while to read and the frst bootstrap moves on too fast. How do I edit the timeout for the first bootstrap anyways? So, my main question is, how do I add a cd booting option to yaboot and then, how doI boot it? The devalias from OpenFrmware tells me that 1 have 2 cd-rom instaled, on is /ht/pci@3/ata-6/disk@0 and the other on ends with a 1 instead of a zero. These are the contents of my yaboot.conf file: yaboot.conf generated by the Ubuntu installer run: "man yaboot.conf" for details. Do not make changes until you have!! see also: /usr/share/doc/yaboot/examples for example configurations. For a dual-boot menu, add one or more of: bsd=/dev/hdaX, macos=/dev/hdaY, macosx=/dev/hdaZ boot="/dev/disk/by-id/scsi-SATA_ST3160023AS_5MT1GCWA-part2" device=/ht@0,f2000000/pci@3/k2-sata-root@c/@0/@0 partition=4 root="UUID=798a048f-ee48-49e0-bba3-111aed8dee04" timeout=12000 install=/usr/lib/yaboot/yaboot magicboot=/usr/lib/yaboot/ofboot enablecdboot macosx="/dev/disk/by-id/scsi-SATA_ST3160023AS_5MT1GCWA-part3" image=/boot/vmlinux label=Linux read-only initrd=/boot/initrd.img append="quiet splash" What do I add here so that yaboot will boot from my cd in like 3 minutes after startup? Thanks!

  Read the article

• Merging two sites into one, how to redirect from the domain that's going away?

  - by bikeboy389

  I haven't been able to find any existing questions that cover my exact issue, so here goes: My client wants her two sites (domain1.com and domain2.com) rolled into a single, new site under domain1.com. Once the site is ready on domain1.com, DNS for domain2.com would be pointed at the same server as domain1.com. I know how to do an htaccess rewrite rule that would make all domain2.com traffic map to a specific single page or directory within domain1.com. But that's not what the client wants. What she wants is for a bunch of specific pages on domain2.com to map to specific new pages on domain1.com. For example: domain2.com/index.php?pageid=58 GOES TO domain1.com/2011/04/somearticle domain2.com/index.php?pageid=92 GOES TO domain1.com/2011/03/differentname etc. I could put a bunch of 301 redirects in the htaccess on domain1.com, which would work fine. The problem is, the client doesn't want/need specific redirects for ALL the domain2.com pages, and if I just do 301 redirects, anybody who comes looking for a domain2.com page that I haven't built a specific redirect for will get a 404 error. So I need to use 301 redirects for some traffic, and a rewrite rule for any traffic that's not covered in the 301 redirects. How do I do sort of a blending of a rewrite rule and 301 redirects, all in the htaccess file for domain1.com? Is this possible? Is it as simple as putting the 301 redirects in the htaccess file first, then doing the rewrite rule? I'm guessing not.

  Read the article

• Step by Step: Remove/Sideline Preinstalled Windows 8, Install Ubuntu

  - by user207562

  I want Ubuntu as my primary/only operating system. Computer came with presumptive Pre-Installed Windows 8.(touch screen) Help. New Dell Inspiron 15r. Cannot install Ubuntu 12.04-03 or LTS. I need/request step by step instructions to remove Windows 8 or sideline Windows 8. (ie) BIOS settings I need to know: What to have; What settings; When to apply; Boot manager settings. UEFI. Etc. This should be easy, but I am mired in the Herpes that is Microsoft. I end up having a presumed dual boot that will not access Ubuntu. (ie) Step 1: Turn on computer. Step 2: F# to change ... to ... at Dell prompt... I want to use Ubuntu as my primary operating system or my only operating system.

  Read the article

• Why am I getting [mount error(22): Invalid argument] while trying to mount SMB network drive?

  - by Steve_

  Disclaimer: I am very new to Linux :) Anyway, onward: I have a fresh instance of Ubuntu Server (12.04.1 LTS) running on my network and I want to mount a network drive to the server so I can access the contents. The network drive is a SAMBA compatible drive running Darwin OS. If I run the following command: smbclient -L //192.168.0.2 -U myuser It prompts me for the password and then displays output similar to: Domain=[SERVER01] OS=[Darwin] Server=[@(#)PROGRAM:smbd PROJECT:smbx-105.4.0] Sharename Type Comment --------- ---- ------- Comp Staff's Public Folder Disk CompRaid03 Disk Dropbox Disk Groups Disk IPC$ IPC Public Disk Users Disk compstaff Disk However, when I try and mount the CompRaid03 share, using this command: sudo mount -t cifs //192.168.0.2/CompRaid03 /mnt/myshare -o username=myuser I get the same password prompt, but after putting the correct password in, I received this error: mount error(22): Invalid argument dmesg | tail returns: [23576.037373] CIFS VFS: cifs_mount failed w/return code = -22 I don't understand what is wrong with this command. I've managed to mount a share on my current (Windows 8) machine using basically the same command but with a different IP address and share name (obviously). I've spent a good few hours trying to solve this and got no where. Any help or pointers would be greatly appreciated. Thanks Steve EDIT As suggested I've also trued using "user=" instead of "username=": sudo mount -t cifs //192.168.0.2/CompRaid03 /mnt/svnrepo -o user=myuser This results in the same "Invalid argument" error.

  Read the article

• How do I make a Live USB without destroying my Windows computer?

  - by user71089

  Unlike every other post I have read, let me begin by saying that I am TERRIFIED of destroying my Windows 7 home system in the attempt of making a bootable Ubuntu Thumb Drive. I very specifically DO NOT want to attempt configuring a dual boot system. What I am seeking is a portable operating system on a thumb drive, through which I can run my COREL software via VirtualBox-4.1.16-78094-Win. I want to be able to use my own software on my work computer without any worries about screwing up the host system anywhere I go. Supposedly, I just made a bootable Thumb drive, having successfully loaded the ISO for ubuntu-12.04-desktop-i386 using Pendrivelinux's Universal-USB-Installer-1.9.0.1 However, all that I get is a Thumb Drive that wants to install Unbutu onto my PC's HDD. I am not finding any clear path to this end in the posts I am reading. Like it or not, Windows is a fact of life for me. The goal is to be able to use my software on my work PC without doing anything intrusive that will cost me my job. If I have a meltdown on my PC at home trying to make this happen, it will be nearly as bad. Is this even Do-Able? Can the process be made clear? Thank You, Ubuntu World ...!

  Read the article

• Why does my system slow down or freeze when there is heavy disk activity?

  - by user72270

  Im a first-time user to Ubuntu-12.04 with WUBI installation. My NoteBook Information : Dell vostro 3450 : i5 2410m, 3 gb ram, intel hd3000, amd 6630m hybrid. Surfing and playing games works flawlessly, however, I'm having huge problems when installing applications and generally copying and moving files. When doing so, system is significantly slower and freezes quite often (Firefox gets bluish, sometimes even black n white). I would say that Ubuntu allocates too much resources on file transfers and installing, but even these tasks are very slow. Here is very specific example : today, i tried to move 6 GB file from win 7 installation. It was good at first, i jumped to firefox but after a while firefox started to randomly turn bluish and mouse was randomly stopping working. It was gradually worse and worse and it got to a point when firefox black n whited and mouse wasn't working at all. I raged and went for some meal, when i got back screen was black. It probably unlogged me due to inactivity, when i pushed random button to bring screen to life i had to wait few minutes to let it show me only my screen background. No log in screen, just background and working mouse. NoteBook fan was working at 100 % so I assumed that file transfer was going on and I left it to work. Nothing then changed for a full hour so I hard rebooted it. File transfer unsuccessful, It transfered hardly 2 gigs. Is this normal ? What to do in these situations ? It didn't let me load system manager and not even terminal. Thanks.

  Read the article

< Previous Page | 206 207 208 209 210 211 212 213 214 215 216 217  | Next Page >