Search Results

Search found 6976 results on 280 pages for 'active'.

Page 211/280 | < Previous Page | 207 208 209 210 211 212 213 214 215 216 217 218  | Next Page >

• How to redirect all Internet traffic to OpenVPN Server

  - by JuliaS

  I have seen working solutions around the issue of forcing Internet traffic to go through the OpenVPN server but they are all done in Linux, all I want to know is how to add an entry to the route table in windows to make this happen. connectivity between the client and server is fine, my Windows 7 client can establish a connection to the Windows 2008 Server, but when established Internet traffic is still going from the local Windows 7 machine. Here are the details: Server: Windows 2008 Server with one NIC OpenVPN IP Address: 192.168.0.1 Local NIC IP Address (connects the server to the Internet): 10.242.69.107 Client: Windows 7 with one NIC OpenVPN IP Address: 192.168.0.2 ISP allocated IP Address: 10.0.8.2 (gateway 10.0.8.1) Server OpenVPN Config: dev tun ifconfig 192.168.0.1 192.168.0.2 secret static.key push "redirect-gateway def1" Client OpenVPN Config: remote xxx.xxx.com dev tun ifconfig 192.168.0.2 192.168.0.1 secret static.key I'm not an expert with adding routes...etc. I would be grateful if someone could let me know how to add this entry in my server/client route table. EDIT: Output from the client's netstat -rnv IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.0.8.1 10.0.8.2 20 10.0.8.0 255.255.255.252 On-link 10.0.8.2 276 10.0.8.2 255.255.255.255 On-link 10.0.8.2 276 10.0.8.3 255.255.255.255 On-link 10.0.8.2 276 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.0.0 255.255.255.252 On-link 192.168.0.2 286 192.168.0.2 255.255.255.255 On-link 192.168.0.2 286 192.168.0.3 255.255.255.255 On-link 192.168.0.2 286 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 10.0.8.2 276 224.0.0.0 240.0.0.0 On-link 192.168.0.2 286 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 10.0.8.2 276 255.255.255.255 255.255.255.255 On-link 192.168.0.2 286 ===========================================================================

  Read the article

• sorry, the maximum allowed clients from your host (10) are already connected" FTP error

  - by Sejanus

  Hello, I keep getting the "sorry, the maximum allowed clients from your host (10) are already connected" error whenever I try to transfer a large number of files. At first I thought it's a filezilla bug, however I get the same error basically with every FTP client I've tried, including Total Commander under Wine. I do not get that error using Windows. I did try to limit maximum allowed connections for Filezilla, both in server settings and in global settings, it didnt change anything. I did try to switch between passive and active modes (not sure if it's related at all, just last desperate attempt), and it didnt change anything either. When I try to use native ftp client (not sure how is it called, the one in Places - Connect to a server) I get abstract "connection refused" error every time I transfer large number of files. Connection is refused for separate particular files, if I click "Ignore" each time the rest of files are transfered perfectly well, so I assume it's the very same error. Anything I could do? This really drives me mad, transfering large numbers of files is a part of my everyday job... P.S. and this happens with many different FTP servers. Also I dont get this error in Windows. So I assume it's not a server problem. P.P.S. I am aware of similar question here, the answer provided just didn't solve it to me.

  Read the article

• Why does Mysql Xampp restart only when i run the mysqld.exe file manually?

  - by Ranjit Kumar

  I am using mysql-xampp v3.0.2 version. while restarting the mysql server first it show me the running status and after 2or3s it stops running automatically. So as of now i got a temporary solution like going into xampp installation folder Xampp-mysql-bin-running the msqld.exe file. i dont know whether it is the correct solution or is there any alternate solution to be made !! please suggest me errorlog 120629 15:29:59 [Note] Plugin 'FEDERATED' is disabled. 120629 15:29:59 InnoDB: The InnoDB memory heap is disabled 120629 15:29:59 InnoDB: Mutexes and rw_locks use Windows interlocked functions 120629 15:29:59 InnoDB: Compressed tables use zlib 1.2.3 120629 15:29:59 InnoDB: Initializing buffer pool, size = 16.0M 120629 15:29:59 InnoDB: Completed initialization of buffer pool InnoDB: The first specified data file D:\xampp\xampp\mysql\data\ibdata1 did not exist: InnoDB: a new database to be created! 120629 15:29:59 InnoDB: Setting file D:\xampp\xampp\mysql\data\ibdata1 size to 10 MB InnoDB: Database physically writes the file full: wait... 120629 15:29:59 InnoDB: Log file D:\xampp\xampp\mysql\data\ib_logfile0 did not exist: new to be created InnoDB: Setting log file D:\xampp\xampp\mysql\data\ib_logfile0 size to 5 MB InnoDB: Database physically writes the file full: wait... 120629 15:30:00 InnoDB: Log file D:\xampp\xampp\mysql\data\ib_logfile1 did not exist: new to be created InnoDB: Setting log file D:\xampp\xampp\mysql\data\ib_logfile1 size to 5 MB InnoDB: Database physically writes the file full: wait... InnoDB: Doublewrite buffer not found: creating new InnoDB: Doublewrite buffer created InnoDB: 127 rollback segment(s) active. InnoDB: Creating foreign key constraint system tables InnoDB: Foreign key constraint system tables created 120629 15:30:02 InnoDB: Waiting for the background threads to start

  Read the article

• What causes "A disk read error occurred, Press Ctrl + Alt + Del to restart"?

  - by Mehrdad

  I have a virtual machine containing Windows XP SP3. When I resized the VHD file (and the embedded partition), and tried booting, I got: A disk read error occurred Press Ctrl + Alt + Del to restart Some notes: FixBoot and FixMBR don't help. ChkDsk doesn't help. The partition is indeed active. The partition starts at sector 63 (it also did so before the problem) of cylinder 1, head 1, and is marked as type 0x07 (NTFS) My host OS reads the VHD and the partition completely fine I'm interested in knowing the cause rather than the fix. So "re-format the disk", "reinstall Windows", etc. aren't valid solutions. It's a virtual machine after all... I have nothing to lose, so I don't care about fixing it. I just want to know what's causing this problem, in case I run into it again on a physical machine (which I have done before). More info: The layout of the original, dynamic VHD (which works correctly): +-----------------------------------------------------------------------------+ ¦ Disk: 3 MBR/GPT: MBR ¦ ¦ Size: 127.00GB CHS: 16578 255 63 ¦ ¦ Sectors: 266338304 Disk Signature: 0xEE3EEE3E ¦ ¦ Partitions: 1 Partition Order: 1 ¦ ¦ Media Type: Fixed Interface: SCSI ¦ ¦ Description: Msft Virtual Disk ¦ +-----------------------------------------------------------------------------¦ ¦Pos Idx Type/Name Size Boot Hide Start Sector Total Sectors DL Vol Label ¦ +--- --- --------- ---- ---- ---- -------------- -------------- -- -----------¦ ¦ 1 1 07-NTFS 1.5G Yes No 63 3,148,677 F: <None> ¦ +-----------------------------------------------------------------------------+ The layout of the resized, fixed-size VHD (which doesn't work): +-----------------------------------------------------------------------------+ ¦ Disk: 3 MBR/GPT: MBR ¦ ¦ Size: 1.50GB CHS: 196 255 63 ¦ ¦ Sectors: 3149824 Disk Signature: 0xEE3EEE3E ¦ ¦ Partitions: 1 Partition Order: 1 ¦ ¦ Media Type: Fixed Interface: SCSI ¦ ¦ Description: Msft Virtual Disk ¦ +-----------------------------------------------------------------------------¦ ¦Pos Idx Type/Name Size Boot Hide Start Sector Total Sectors DL Vol Label ¦ +--- --- --------- ---- ---- ---- -------------- -------------- -- -----------¦ ¦ 1 1 07-NTFS 1.5G Yes No 63 3,148,677 F: <None> ¦ +-----------------------------------------------------------------------------+

  Read the article

• Limiting bandwidth on internal interface on Linux gateway

  - by Jack Scott

  I am responsible for a Linux-based (it runs Debian) branch office router that takes a single high-speed Internet connection (eth2) and turns it into about 20 internal networks, each with a seperate subnet (192.168.1.0/24 to 192.168.20.0/24) and a seperate VLAN (eth0.101 to eth0.120). I am trying to restrict bandwidth on one of the internal subnets that is consistently chewing up more bandwidth than it should. What is the best way to do this? My first try at this was with wondershaper, which I heard about on SuperUser here. Unfortunately, this is useful for exactly the opposite situation that I have... it's useful on the client side, not on the Internet side. My second attempt was using the script found at http://www.topwebhosts.org/tools/traffic-control.php, which I modified so the active part is: tc qdisc add dev eth0.113 root handle 13: htb default 100 tc class add dev eth0.113 parent 13: classid 13:1 htb rate 3mbps tc class add dev eth0.113 parent 13: classid 13:2 htb rate 3mbps tc filter add dev eth0.113 protocol ip parent 13:0 prio 1 u32 match ip dst 192.168.13.0/24 flowid 13:1 tc filter add dev eth0.113 protocol ip parent 13:0 prio 1 u32 match ip src 192.168.13.0/24 flowid 13:2 What I want this to do is restrict the bandwidth on VLAN 113 (subnet 192.168.13.0/24) to 3mbit up and 3mbit down. Unfortunately, it seems to have no effect at all! I'm very inexperienced with the tc command, so any help getting this working would be appreciated.

  Read the article

• I used disk copy to clone my drive, now my windows 7 profile won't load correctly

  - by RzK

  I used easeuse disk copy, after acronis, clonezilla, windows image restore failed me. Basically it copys all sectors, I set it to skip bad sectors(40). The source drive works, it just gave me a couple errors and stopped booting at one point. The drive is an identical copy, minus 40 bad errors. The drive is set to C and active partition, I rebuilt the boot order. I've ran sfc /scannow and ran chkdsk /r chkdsk found 20kb of bad sectors if I remember right. Now the issue I get is when I log into my profile which was saved right, I get a blank light blue wallpaper (non-license) explorer.exe is not running, and there are only 4 processes running in taskmanager, including taskmanager. I would try a repair install but CRTL-E would not open, nothing will open once I force start explorer.exe, almost like all services are down. What should I do? Fresh install is almost not a possibility I will try and fix this issue. sfc /scannow /offbootdir=c:\ /offwindir=c:\windows returns "Windows Resource Protection could not perform the requested operation"

  Read the article

• Problem with wireless networking

  - by Rodnower

  Hello, I have atheros wifi hardware, intell chipset, gigabyte laptop and CentOS 5 installed. Now I try to use wireless network and get problems. First of all I want to say that I have 2 OS on my laptop, and when I load Windows XP I still may to access to the wireless network. First I try to get it on Linux was to make active wlan0 interface in: system - administration - network but I get: Determining IP information for wlan0... failed. Second I try also was unsuccessfully: [root 1 network-scripts]# ifup-wireless Error : unrecognised wireless request "off" This relevant output of iwconfig is: Warning: Driver for device wlan0 recommend version 21 of Wireless Extension, but has been compiled with version 20, therefore some driver features may not be available... wlan0 IEEE 802.11 ESSID:"" Mode:Managed Frequency:2.462 GHz Access Point: Not-Associated Tx-Power=27 dBm Retry min limit:7 RTS thr:off Fragment thr=2352 B Encryption key:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 {output not in the original format} The same things are happen even if I do: modprobe wlan0 (this not get error) Important to say that modprobe not succeed to find ath_pci, tharefor I decide to download latest version of the madwifi driver from http://madwifi-project.org. I extracted this, but when I make this, this is what I get: [root 1 madwifi-0.9.4]# make /bin/sh: line 0: cd: /lib/modules/2.6.18-164.el5/build: No such file or directory Makefile.inc:66: * /lib/modules/2.6.18-164.el5/build is missing, please set KERNELPATH. Stop. I tried to set KERNELPATH, but I think that it was incorrect: [root 1 madwifi-0.9.4]# make KERNELPATH=/lib/modules/2.6.18-164.el5/kernel/ /bin/sh: cc: command not found Makefile.inc:81: * Cannot detect kernel version - please check compiler and KERNELPATH. Stop. Some one have any ideas? Thank you very much for ahead.

  Read the article

• Postfix: change sender in queued messages

  - by ring0

  Following a complete re-installation we got a problem with the configuration: the sender address was wrong and some recipients (mail servers) rejected them. So there is a bunch of mails stuck in the Postfix queue. Ideally, a change of the sender address directly in the queued mails, and then flushing the queue would be optimal. I tried this answer that addresses this very problem. But messages don't seem to be easily modifiable in the version I have (2.11.0). For instance there is no /var/spool/mqueue dir, but, instead, /var/spool/postfix/... active bounce corrupt defer deferred dev etc flush hold incoming lib maildrop pid private public saved trace usr and the dir of interest is deferred. I tried to modify a few files there changing the wrong domain with the correct one (and was careful to ensure only those were changed). But then, those mails were moved to corrupt, meaning that a simple text change doesn't seem to work (done with vi). Any other cleaner way to change the sender in queued mails?

  Read the article

• NetBackup prefers "Scratch" tapes over dedicated tapes

  - by wfaulk

  I have a NetBackup 6.0MP7 installation running on Windows Server 2003. It functions as the only Master Server and Media Server. I swap a full set of tapes in and out every week, but leave a set of tapes with their Volume Pool set to "Scratch" in all the time. The weekly tape sets then get rotated back in after a period of time. Largely, this works fine. I seldom actually need the scratch tapes, but every once in a while, a backup will run over what I have dedicated to the task. However, one week's set of tapes consistently gets declined in favor of the scratch pool. The backup policies are the same for every week, they all have "Policy Volume Pool" set to "NetBackup", and all of the tapes for every week (beside the scratch tapes) have had their pools assigned as "NetBackup", definitely including the week that always gets ignored. That said, it doesn't ignore all of the NetBackup pool tapes for that week. It does usually write to two or three of them, but it writes to like 20 of the scratch tapes. (I haven't thought to look to see if it's always the same two or three tapes.) And this problem never seems to occur for any other week. It doesn't load the tapes and then reject them; it never seems to try to use them at all. They are not flagged as frozen. They are all active and unassigned when I swap them in. The tapes are in a Quantum PX510 tape library. The NetBackup server is attached to the library/robot via fibrechannel going through an HP-branded Brocade switch. I'm not an expert on NetBackup at all. I don't really even know where to look. Any advice on logs to look at or logging to enable or really anything at all would be appreciated. I'll keep an eye on the question and update it if anyone needs any more info to help.

  Read the article

• Ubuntu raid 1 write errors

  - by Micah

  I have an Ubuntu server set up with two SATA drives in a RAID 1 configuration with MDADM. The machine is used to record raw video, which involves a lot of writing to the disk. Sometimes during video recording the computer will crash, will the following errors in kern.log: Mar 15 10:39:41 video kernel: [414501.629864] ata2.00: exception Emask 0x10 SAct 0x0 SErr 0x400100 action 0x6 Mar 15 10:39:41 video kernel: [414501.629870] ata2.00: BMDMA stat 0x26 Mar 15 10:39:41 video kernel: [414501.629875] ata2.00: SError: { UnrecovData Handshk } Mar 15 10:39:41 video kernel: [414501.629880] ata2.00: failed command: WRITE DMA EXT Mar 15 10:39:41 video kernel: [414501.629889] ata2.00: cmd 35/00:00:28:6d:f6/00:04:06:00:00/e0 tag 0 dma 524288 out Mar 15 10:39:41 video kernel: [414501.629891] res 51/84:b1:77:6e:f6/84:02:06:00:00/e0 Emask 0x30 (host bus error) Mar 15 10:39:41 video kernel: [414501.629896] ata2.00: status: { DRDY ERR } Mar 15 10:39:41 video kernel: [414501.629899] ata2.00: error: { ICRC ABRT } Mar 15 10:39:41 video kernel: [414501.629910] ata2.00: hard resetting link Mar 15 10:39:41 video kernel: [414501.973009] ata2.01: hard resetting link Mar 15 10:39:41 video kernel: [414502.482642] ata2.00: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Mar 15 10:39:41 video kernel: [414502.482658] ata2.01: SATA link down (SStatus 0 SControl 300) Mar 15 10:39:41 video kernel: [414502.546160] ata2.00: configured for UDMA/133 Mar 15 10:39:41 video kernel: [414502.546203] ata2: EH complete Is this the result of faulty drives? Is software RAID just not performant enough for data rates ~15 MB/s, even with a quad-core i7? Thanks for your help. Edit: cat /proc/mdstat returns this: Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md0 : active raid1 sdb1[1] sda1[0] 976760768 blocks [2/2] [UU] unused devices: <none>

  Read the article

• DHCP forwarding behind access list on a Cisco Catalyst

  - by Ásgeir Bjarnason

  I'm having some trouble with forwarding DHCP from a subnet behind an access list on a Cisco Catalyst 4500 switch. I'm hoping somebody can see the mistake I'm making. The subnet is defined like this: (first three octets of IP addresses and vrf name anonymized) interface Vlan40 ip vrf forwarding vrf_name ip address 10.10.10.126 255.255.255.0 secondary ip address 10.10.10.254 255.255.255.0 ip access-group 100 out ip helper-address 10.10.20.36 no ip redirects I tried turning on a VMWare machine on this subnet that was configured to use DHCP, but I never got a DHCP response and the DHCP server didn't receive a request. I tried putting the following in the access-list: access-list 100 permit udp host 10.10.10.254 host 10.10.20.36 eq bootps access-list 100 permit udp host 10.10.10.254 host 10.10.20.36 eq bootpc access-list 100 permit udp host 10.10.20.36 host 10.10.10.254 eq bootps access-list 100 permit udp host 10.10.20.36 host 10.10.10.254 eq bootpc That didn't help. Can anybody see what the problem is? I know that the DHCP server works; our whole network is running off of this DHCP server I also know that the subnet works because we have active servers running on the network The DHCP scope is already defined on the DHCP server The subnet is correctly defined on the VMWare server (already servers running on the subnet on VMWare) Edit 2012-10-19: This is solved! The subnet had formerly been defined as a /25 network, but was then expanded into a /24 network. When the DHCP scope was altered after this change it was done incorrectly; the gateway was moved to .254, the leasable IP range was in the lower half of the /24 subnet but we forgot to change the CIDR prefix from /25 into /24. This happened some 2 years ago, and we didn't need to use DHCP on this server network again until this week. Thank you MDMarra and Jason Seemann for looking at the question and trying to troubleshoot. Now I'm wondering if I should mark Jason's answer as the accepted answer (I am new to the Stack Exchange network, so I don't know the etiquette of what to do if I misstated the question like in this case).

  Read the article

• Blank desktop when logging into a Virtualized Windows 2008 Terminal Server?

  - by Rachel

  We have a Virtualized Terminal Server running Windows Server 2008. When the admin user logs in, everything is fine. When anyone else logs in, their desktop and start menu is blank (they have the taskbar, start button, and quick launch links though). If I go into Windows Explorer, I can see icons in their desktop folder (although the icon image is missing and it is just displaying the generic icon), but can't run any of them. If I login with a user that is part of the Administrator group in Active directory, I get the same behavior except I can launch the programs found in the Desktop Folder of Windows Explorer. I cannot drag these items out onto the desktop though - The cursor doesn't allow me to drop them. From Task Manager I can see that explorer.exe and dwm.exe are both running. The Authenticated Users and Interactive groups are both under the Users group, along with our network's Domain Users group. Does anyone know why this is happening and how I can fix it? Also, not sure if it's related but about 1 in every 3 logins just hangs at a completely blank blue screen (no start button, taskbar, or quick launch buttons) and needs to be disconnected / reset by an admin. Edit I just noticed that the desktop itself doesn't even respond to click events. It's almost like the entire desktop is missing. At first I thought it didn't respond to right-click events because of an AD policy, but then I noticed if you open the Start Menu and click the desktop, the start menu doesn't shut like it should

  Read the article

• Workstations cannot see new MS Server 2008 domain, but can access DHCP.

  - by Radix

  The XP Pro workstations do not see the new replacement domain upon boot; they only see their cached entry for the old (server 2003) domain controller. The old_server is not connected to the network. I have DHCP working with the same scope as the old_server. In my "before-asking" search for a solution I came across the following two articles, and I recall doing things as suggested by the articles. http://www.windowsreference.com/windows-server-2008/how-to-setup-dhcp-server-in-windows-server-2008-step-by-step-guide/ http://www.windowsreference.com/windows-server-2008/step-by-step-guide-for-windows-server-2008-domain-controller-and-dns-server-setup/ The only possible issue is: I was under the impression that the domain netbios needed to match the DC's netbios. The DC netbios is city01 while the domain's FQDN is city.domain.org (I think this is mistaken and should have been just domain.org) But, the second link led me to a post which I believe answers my question. I did as they instructed by opening Local Area Connection Properties, then selecting TCP/IPv4 and setting the sole preferred DNS server to the local hosts static IP (10.10.1.1). Search for "Your problems should clear up" for the post I'm referencing: http://forums.techarena.in/active-directory/1032797.htm Have I misunderstood their instructions? I am hoping to reach the point where I can define users and user groups. Also, does TechNet have a single theoretical overview document I could read. I really don't like treating comps as magic. I will be watching this closely and will quickly answer any questions. If I've left anything out it is because I did not know it was needed. PS: I am loath to ask obviously basic questions, but I am tired and wish to fix this before tomorrow. Also, this is my first server installation, thank you for your help.

  Read the article

• How can I "share" a network share over the internet to multiple operating systems?

  - by Minsc

  Hello all, We have a network share accessible through our intranet that is widely used. This share has it's own set of fine tuned permissions. I have been tasked with allowing A.D. authenticated access to this share over the internet without the use of VPN. The internet access has to mimic the NTSF permissions in place on the share. Another piece of the puzzle is that the access over the internet has to allow perusal of the share from Windows and Mac OS systems. I had envisioned a web front end that would facilitate downloading to and uploading from the share via a web browser. I'm trying to ask for some suggestions about what type of setup is necessary to achieve this. I've done loads of testing and searching for solutions but I can't seem to get anything to work as I hope. The web server that will be handing all of this is a Windows 2K8 box with IIS 7. How can I allow the users to authenticate against Active Directory when coming from the internet even when coming from a Mac system? I hope my question is not too broad, I'm sorry if I should have broken it up into multiple questions. It all is just tied together in my head. Thank you all for your time and aid.

  Read the article

• Numeric UIDs/GIDs in ACLs on OS X server (10.6)

  - by Oliver Humpage

  Hi, On one (old OS X 10.4) server I'm tarring up some files which have ACLs. I'm then using ``tar -xp'' to untar the archive onto a new 10.6 server, which doesn't have any users/groups configured on it yet except the default admin (UID 501) (there's a reason for that, don't ask!). Obviously this means an "ls -lne" will list files and ACLs with numeric UIDs and GIDs. Now for the normal file permissions it makes sense: you get UIDs like "1037". And for some ACLs, it also makes sense: you get things like "AAAABBBB-CCCC-DDDD-EEEE-FFFF00000402" for groups (0x402 = GID 1026) and "FFFFEEEE-DDDD-CCCC-BBBB-AAAA000001F5" for users (0x1F5 = UID 501). However, some ACLs have a UIDs like "E51DA674-AE70-41BC-8340-9B06C243A262" or GIDs like "0A3FCD24-0012-46FA-B085-88519E55EF29" and I have absolutely no idea how to translate these IDs back into something that could be matched back to the original IDs (UID 1072 and GID 1047 respectively in this example). Can anyone help me translate these weird long hex strings? (Basically we're moving from local users to an Active Directory setup, so I want to move all files to the new server with permissions intact, then chmod, chgrp and set ACLs such that we translate old IDs to the new AD IDs. Hence needing some way to map between the sets. I don't believe there's an easier way to do this?) Many thanks, Oliver.

  Read the article

• Clustering/load balancing for cluster unaware applications

  - by AaronLS

  Forgive me if I use any of these terms incorrectly. I am wondering if there is any kind of software that would allow my two "join" two computers together such that a cluster unaware application could utilize their combined computing resources? By "cluster unaware" I mean an application that isn't designed to share work across multiple services. My understanding is that clustering is enabled by the specific application by it's architecture, such that messaging with multiple instances of the application coordinate the sharing of work. Instead I am looking for something that enables clustering at the OS or virtualization level, so that any application could essentially be clustered. Failing that, I am also wondering about the following scenario: We have 3 different applications we will call A, B, and C. We have 2 single core computers. At any given time lets say that any combination of those applications will be CPU intensive. In cases where only 2 of those apps are very active, have one of them moved over to a different server. In a nutshell, some sort of dynamic automatic shuffling of the application's load. I have heard of virtual machines that can be migrated across physical machines while live, but I am wondering if this can be done automatically in response to an application's or VM's CPU activity?

  Read the article

• How do I install the main repositories for RHEL6

  - by eisaacson

  We've setup RHEL6 on a new server. As far as we can tell, our subscription is all setup properly. However, when I run yum repolist, it doesn't show any repositories. /etc/yum.repos.d/redhat.repo is empty. I tried pasting in the content from another RHEL6 server's redhat.repo but as soon as I run yum, it wipes it out again. I just need to get the basic RedHat repositories setup so I can install packages. EDIT: Using the GUI, I went to System Administration Red Hat Subscription Manager. Under the 'Products' tab, it did not show any products. EDIT: When I run yum update, here's what I get: # yum update Loaded plugins: product-id, refresh-packagekit, security, subscription-manager This system is receiving updates from Red Hat Subscription Management. Setting up Update Process No Packages marked for Update When I log in to RedHat customer portal, it shows that subscription as active. EDIT: To make sure I wasn't having a subscription issue. I re-registered and re-subscribed. I get all the same results. # subscription-manager register --force # subscription-manager subscribe --pool=*redacted* EDIT: contents of /etc/yum.conf [main] cachedir=/var/cache/yum/$basearch/$releasever keepcache=0 debuglevel=2 logfile=/var/log/yum.log exactarch=1 obsoletes=1 gpgcheck=1 plugins=1 installonly_limit=3 contents of /etc/yum/pluginconf.d/rhnplugin.conf: [main] enabled = 0 gpgcheck = 1

  Read the article

• MacPorts pHash not showing up in Python

  - by Nitzan Wilnai

  I am having a problem where python does not show pHash installed even though I installed it using macports. I made sure I am using the MacPorts version of Python by doing: sudo port select --set python python27 I then installed pHash by doing: sudo port install pHash. It installed without any errors. When I call help('modules'), I do not see pHash listed among the installed packages. Any ideas on why python is not seeing the pHash install by MacPorts? Calling port select --list python shows the following: Available versions for python: none python25-apple python26-apple python27 (active) python27-apple Printing out sys.path outputs the following: (reformatted to make it easier to read here) ['/Library/Python/2.7/site-packages/boto-2.9.9-py2.7.egg', '/Library/Python/2.7/site-packages/setuptools-0.9.8-py2.7.egg', '/Library/Python/2.7/site-packages/pip-1.4.1-py2.7.egg', '/opt/local/Library/Frameworks/Python.framework/Versions/2.7/lib/python27.zip', '/opt/local/Library/Frameworks/Python.framework/Versions/2.7/lib/python2.7', '/opt/local/Library/Frameworks/Python.framework/Versions/2.7/lib/python2.7/plat-darwin', '/opt/local/Library/Frameworks/Python.framework/Versions/2.7/lib/python2.7/plat-mac', '/opt/local/Library/Frameworks/Python.framework/Versions/2.7/lib/python2.7/plat-mac/lib-scriptpackages', '/opt/local/Library/Frameworks/Python.framework/Versions/2.7/lib/python2.7/lib-tk', '/opt/local/Library/Frameworks/Python.framework/Versions/2.7/lib/python2.7/lib-old', '/opt/local/Library/Frameworks/Python.framework/Versions/2.7/lib/python2.7/lib-dynload', '/opt/local/Library/Frameworks/Python.framework/Versions/2.7/lib/python2.7/site-packages', '/Library/Python/2.7/site-packages'] Can anyone help? Thanks.

  Read the article

• Enabling Samba Shares Across Subnets

  - by John

  I was curious how I could go about setting up SAMBA so that shares could be seen and used across different subnets. We have some Linux devices that are bound to Active Directory and we would like to have them serve SAMBA shares to clients that will reside in a different subnet than what the servers reside in? Is there any way to do this without needing to setup a WINS server or use legacy NetBIOS methods since the majority of our clients are Windows 7, Windows Server 2003, Windows Server 2008, and Macintosh OS X (10.6 or newer)? EDIT Right now, only clients in the same subnet as the SAMBA server can see the shares. Clients outside of the subnet (i.e. the client subnet) cannot see or connect to the share. The error returned is: The specified network name is no longer available. It does not seem to matter if I use IP, FQDN, or NetBIOS name to try and connect to the share with. We have a common Cisco router handling the inter-subnet routing. Everything else seems to work correctly with this network setup and the device can be pinged from multiple subnets. I also do not believe it to be a firewall type of issue since the rules for this segment are rather lax.

  Read the article

• SharePoint Backup/Restore without stsadm

  - by Kevin

  Due to problems we found with the restore of sites/site collections using stsadm (our tasks generated from workflows were not restored), we've taken a different route for backup/restore. We plan a major customization to our SP site and want to take a backup so we can rollback in case the install fails. In our System Testing (not production) environment, we've backed up the 12 hive, the virtual dir's that the IIS points to SharePoint, and the SharePoint databases in SQL (using SQL server to do the db backups). We have custom event handlers and workflows built with Visual Studio, and deploy the dlls to the GAC as version 2 (signed and versioned in Visual Studio). So when we deploy, the GAC will contain 2 versions of the workflows - version 1 and version 2. During the deploy we use SP stsadm features to install/activate the WF's. We also go to each library and add the new, version 2 WFs. This automatically sets the version 1 WF's to "Not Allow" new instances (which is what we want) and the version 2 as active - perfect so far. When we've completed the install, we then assume a failure and attempt to restore to the same machines (SharePoint on one server, SQL on another). We start by uninstalling the version 2 WF's from the GAC, reset IIS (to clear cache of these ver. 2 WF dlls'), restore the 12-hive and virtual directory folders, then restore the SQL dbs. This is all just as manual as you read it - no stsadm here. All seems to work after our restore, it appears the restore was successful - the mods we made to column names, data changes, etc during the install are all reverted back to the original pre-install state. With one exception. When we run a workflow, it always fails and the Logs in the 12-hive indicates the WF is still trying to use the version 2 of the dll (System.IO file not found error) We think we've backed up and restored all the moving pieces of Sharepoint but we're missing something here, does anybody have any ideas why the version 2 WF dlls are still being referenced eventhough we restored all the folders and db's of SharePoint? Thanks, Kevin

  Read the article

• AWS Application - Subscription Payments Scheduled but Not Initializing

  - by nicorellius

  I briefly browsed the AWS forums but these are not nearly as easy to use and efficient as Stack Exchange derived ones, so here I am... the company I work for has an app on the AWS cloud. In general the app works well. However, since it is new, we haven't had many customers and the ones who signed up are now coming to the point where their subscriptions to our service should be renewed. In comes my question. When I query the database for payment status of certain subscriptions using the console, I get what I would expect: Instrument XYZ is on a Monthly subscription (subscription=xxxyyyzz). The subscription is active with an expiration date of 19 Apr 2010 10:43 Z The payment token will expire on 1 Dec 2012 12:00 Z There are xy runs remaining. The subscription fee of $XX.xx will be charged on 17 Apr 2010 10:43 Z OK, this is great. According to this, I would expect the next payment to be initiated on 17 Apr. The reason I am asking is because for a different user last month I got this same output but the payment never went through, i.e., was not initiated through Amazon payments. The user didn't see the payment go through and neither did we. It should be noted that the initial payments were received. The sign up process works and if the user goes to "pay" from within our app, they will be directed to https://payments.amazon.com to make their payment. Any ideas?

  Read the article

• Mac Management Without Permission and Security

  - by Bart Silverstrim

  I was going through some literature on managing OS X laptops and asked someone some questions about usage scenarios when using the MacBooks. I asked someone more knowledgeable than I about whether it was possible for my Mac to be taken over if I were visiting another site for a conference or if I went on a wifi network at a local coffee house with policies from an OS X Server with workgroup manager (either legit for the site or someone running a version of OS X Server on hardware they have hidden somewhere on the network), which apparently could be set up to do things like limit my access to Finder or impose other neat whiz-bang management features. He said that it is indeed possible for it to happen as it would be assigned via the DHCP server and the OS X server would assume my Mac is a guest and could hand out restrictions and apparently my Mac will happily accept them without notifying me or giving me an option, unlike Windows which I believe would need to be joined to a domain before it becomes "managed" by Active Directory. So my question is as network admins and sysadmins with users traveling with MacBooks, is there a way to reasonably protect your users from having their machines hijacked without resorting to just turning off networking all the time? Or isn't this much of a security hazard? What threat does this pose to the road warriors in your businesses?

  Read the article

• RRAS NAT not working on a certain computer

  - by legenden

  This is driving me crazy. I have a virtualized W2K8 server running RRAS. Every other computer or server on the network can access the internet through the NAT except one. On one server, it just won't work. I can ping the ip address of the NAT gateway just fine, and everything else works. (SMB, etc) DNS, which is hosted by the same server, also works just fine. I have even reinstalled the OS on the problem server and it still doesn't work. Recap of the steps I tried: There are 3 network cards in the server, I tried every one and different switch ports. Not a hardware problem. Reinstalled W2K8 R2 on server with the problem, didn't help. Tried the IP of the internet gateway directly - this did work (!). But I need NAT to work. All firewalls are disabled. Removed computer from domain, deleted computer membership in Active Directory Users and Computers and added it back. Disabled all other network adapters and set a static ip and specified the gateway ip manually. When I tracert a public IP, the first hop (or any other hop) comes up as: C:\>tracert www.google.com Tracing route to www.l.google.com [209.85.225.106] over a maximum of 30 hops: 1 * * * Request timed out. 2 * * * Request timed out. From a different computer, on which NAT works, the first hop comes up as: tracert www.google.com Tracing route to www.l.google.com [209.85.225.105] over a maximum of 30 hops: 1 <1 ms * <1 ms xxxx [10.5.1.1] This is the most bizarre problem I ever came across, and I realize that it's a long shot asking it here given all the details, but I'm pulling my hair out. Maybe someone has an idea...

  Read the article

• SQL Server Windows-only Authentication Strategy problem

  - by Mike Thien

  I would like to use Windows-only Authentication in SQL Server for our web applications. In the past we've always created the all powerful 1 SQL Login for the web application. After doing some initial testing we've decided to create Windows Active Directory groups that mimic the security roles of the application (i.e. Administrators, Managers, Users/Operators, etc...) We've created mapped logins in SQL Server to these groups and given them access to the database for the application. In addition, we've created SQL Server database roles and assigned each group the appropriate role. This is working great. My issue revolves around that for most of the applications, everyone in the company should have read access to the reports (and hence the data). As far as I can tell, I have 2 options: 1) Create a read-only/viewer AD group and put everyone in it. 2) Use the "domain\domain users" group(s) and assign them the correct roles in SQL. What is the best and/or easiest way to allow everyone read access to specific database objects using a Windows-only Authentication method?

  Read the article

• Fix: Connections to SQL Server 2005 on Windows Vista suddenly stop working

  - by NTulip

  On my Vista machine at work, applications and the SQL Server Management Console work fine connecting to SQL Server 2005. Sometimes they are ok for weeks at a time, sometime for hours and then they stop connecting. I've tried everything to get it to work including the installation of SPII and running the user provisioning tool without any luck. The only way to fix it was to restart. The Error: Connections are refused with the standard error message: Cannot connect to SERVER_NAME\INSTANCE_NAME ------------------------------ ADDITIONAL INFORMATION: A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: SQL Network Interfaces, error: 26 - Error Locating Server/Instance Specified) (Microsoft SQL Server, Error: -1) For help, click: http://go.microsoft.com/fwlink?ProdName=Microsoft+SQL+Server&EvtSrc=MSSQLServer&EvtID=-1&LinkId=20476 The Fix: Stop and restart the Sql Server Browser, Sql Server integration, SQL Server Active Directory Helper services. Works like a charm.

  Read the article

< Previous Page | 207 208 209 210 211 212 213 214 215 216 217 218  | Next Page >