Search Results

Search found 27336 results on 1094 pages for 'network state'.

Page 211/1094 | < Previous Page | 207 208 209 210 211 212 213 214 215 216 217 218  | Next Page >

• Nginx works on my linux machine but is not accessible from other computers in my local network

  - by crooveck

  In my LAN network I have a server with Scientific Linux (RedHat or Fedora based distro), I've done yum install nginx but the welcome page is not accessible from other computers in my network. When I do telnet open localhost 80 and then GET / HTTP/1.0 I get some html code from nginx, so it's running for sure. But when I want to connect remotly, doing telnet open 192.168.3.130 80 I get: Trying 192.168.3.130... telnet: Unable to connect to remote host: No route to host So I assume that there is something wrong with my network settings, maybe iptables or something else? Next step, I turned off iptables: service iptables stop and it helped, now I can connect remotely using telnet. So I think, I need to fix my iptables rules. I did some googling and found this rule -A INPUT -m state --state NEW -m tcp -p tcp --dport 80 -j ACCEPT but it still didn't allow me to connect remotely when iptables is up. Can someone please help me setting a proper iptables configuration?

  Read the article

• How does communication between 2 computers in a single network happen?

  - by learner

  Lets say I and my friend connect our computers with a LAN cable. I ping my friend with his IP address. How does it work? Since we are in the same network, we don't even need IP addresses, do we? Isn't IP addressing only relevant in case of inter-network communication? What will the ping command do with his IP address? How will it eventually find his physical address (NIC address)? (no ARP here, because that would involve a router at the edge of the network, which doesn't apply here). Am I wrong somewhere?

  Read the article

• How to access network shares, printers, etc.through Windows 7 Built-In VPN?

  - by mbrion

  After I have successfully connected to a Windows 7 box via the built-in VPN: how do I access shares, shared printers, network appliances, etc.? So, call me bad at googling, but: I can find dozens of articles on "How to Set up a VPN Connection" and "How to connect to a VPN" for Windows 7... but I can't find a single article on how to access resources after connecting. I have a home VPN set up in Windows 7; I was able to connect to it from my friend's Windows 7 machine last night. I expected to be able to UNC into my shares; I also expected to be able to go to "Start Computer" and Click "Network" on the left side, and then see all of the devices on my home network (while the VPN was connected). Am I missing something obvious? How do I make this happen?

  Read the article

• Windows 7,find who accessed my computer on network?

  - by pg2012

  It seems something tried to delete root c:/ folders on my computer and it did started delete process alphabetical order. Not sure what is cause. any known virus? We have company network edition of antivirus running, and full scan did not found any virus activity. That makes me suspious about someone on company network attempt to delete? can this possible? If it is how do we know from windows server that who accessed my computer over network?

  Read the article

• OSI Model

  - by kaleidoscope

  The Open System Interconnection Reference Model (OSI Reference Model or OSI Model) is an abstract description for layered communications and computer network protocol design. In its most basic form, it divides network architecture into seven layers which, from top to bottom, are the Application, Presentation, Session, Transport, Network, Data Link, and Physical Layers. It is therefore often referred to as the OSI Seven Layer Model. A layer is a collection of conceptually similar functions that provide services to the layer above it and receives service from the layer below it. Description of OSI layers: Layer 1: Physical Layer ·         Defines the electrical and physical specifications for devices. In particular, it defines the relationship between a device and a physical medium. ·         Establishment and termination of a connection to a communications medium. ·         Participation in the process whereby the communication resources are effectively shared among multiple users. ·         Modulation or conversion between the representation of digital data in user equipment and the corresponding signals transmitted over a communications channel. Layer 2: Data Link Layer ·         Provides the functional and procedural means to transfer data between network entities. ·         Detect and possibly correct errors that may occur in the Physical Layer. The error check is performed using Frame Check Sequence (FCS). ·         Addresses is then sought to see if it needs to process the rest of the frame itself or whether to pass it on to another host. ·         The Layer is divided into two sub layers: The Media Access Control (MAC) layer and the Logical Link Control (LLC) layer. ·         MAC sub layer controls how a computer on the network gains access to the data and permission to transmit it. ·         LLC layer controls frame synchronization, flow control and error checking.   Layer 3: Network Layer ·         Provides the functional and procedural means of transferring variable length data sequences from a source to a destination via one or more networks. ·         Performs network routing functions, and might also perform fragmentation and reassembly, and report delivery errors. ·         Network Layer Routers operate at this layer—sending data throughout the extended network and making the Internet possible.   Layer 4: Transport Layer ·         Provides transparent transfer of data between end users, providing reliable data transfer services to the upper layers. ·         Controls the reliability of a given link through flow control, segmentation/de-segmentation, and error control. ·         Transport Layer can keep track of the segments and retransmit those that fail. Layer 5: Session Layer ·         Controls the dialogues (connections) between computers. ·         Establishes, manages and terminates the connections between the local and remote application. ·         Provides for full-duplex, half-duplex, or simplex operation, and establishes checkpointing, adjournment, termination, and restart procedures. ·         Implemented explicitly in application environments that use remote procedure calls. Layer 6: Presentation Layer ·         Establishes a context between Application Layer entities, in which the higher-layer entities can use different syntax and semantics, as long as the presentation service understands both and the mapping between them. The presentation service data units are then encapsulated into Session Protocol data units, and moved down the stack. ·         Provides independence from differences in data representation (e.g., encryption) by translating from application to network format, and vice versa. The presentation layer works to transform data into the form that the application layer can accept. This layer formats and encrypts data to be sent across a network, providing freedom from compatibility problems. It is sometimes called the syntax layer. Layer 7: Application Layer ·         This layer interacts with software applications that implement a communicating component. ·         Identifies communication partners, determines resource availability, and synchronizes communication. o       When identifying communication partners, the application layer determines the identity and availability of communication partners for an application with data to transmit. o       When determining resource availability, the application layer must decide whether sufficient network or the requested communication exists. o       In synchronizing communication, all communication between applications requires cooperation that is managed by the application layer. Technorati Tags: Kunal,OSI,Networking

  Read the article

• collectd does not work

  - by bery

  I have installed collectd-5.0.0 on Fedora12 server and would like to run its service for receiving data from clients. I have enabled network plugin and rddtool plugin as commented: collectd.conf in server: BaseDir "/opt/collectd/var/lib/collectd" LoadPlugin "logfile" LoadPlugin network LoadPlugin rrdtool <Plugin network> Listen "192.168.8.37" "25826" </Plugin> collectd.conf in client: LoadPlugin logfile LoadPlugin cpu LoadPlugin network LoadPlugin memory <Plugin network> Server"192.168.8.37" "25826" </Plugin> collectd.log in server: [2011-08-03 02:36:04] Exiting normally. [2011-08-03 02:36:04] rrdtool plugin: Shutting down the queue thread. [2011-08-03 02:36:04] network plugin: Stopping receive thread. [2011-08-03 02:36:04] network plugin: Stopping dispatch thread. [2011-08-03 02:37:11] Initialization complete, entering read-loop. collectd.log in client: [2011-08-02 17:31:44] Initialization complete, entering read-loop. results thst execute netstat on server: netstat -ulpn | grep 25826 udp 0 0 192.168.8.37:25826 0.0.0.0:* 4744/collectd problem: but there is noting in "/opt/collectd/var/lib/collectd/" on ser yes,I move the port number of "25826" as your propose(But I think this is the default port for coolectd).there is no rdd files recived on server. collectd.log in client collectd [2011-08-03 10:01:36] plugin_read_thread: Handling memory'. [2011-08-03 10:01:36] plugin_read_thread: Handlingcpu'. [2011-08-03 10:01:36] plugin_dispatch_values: time = 1312380096.431; interval = 10.000; host = uml; plugin = memory; plugin_instance = ; type = memory; type_instance = used; [2011-08-03 10:01:36] plugin_dispatch_values: time = 1312380096.431; interval = 10.000; host = uml; plugin = cpu; plugin_instance = 0; type = cpu; type_instance = user; [2011-08-03 10:01:36] uc_update: uml/memory/memory-used: ds[0] = 280412160.000000 [2011-08-03 10:01:36] plugin: plugin_write: Writing values via network. [2011-08-03 10:01:36] uc_update: uml/cpu-0/cpu-user: ds[0] = 0.100008 [2011-08-03 10:01:36] plugin: plugin_write: Writing values via network. [2011-08-03 10:01:36] plugin_dispatch_values: time = 1312380096.431; interval = 10.000; host = uml; plugin = memory; plugin_instance = ; type = memory; type_instance = buffered; [2011-08-03 10:01:36] plugin_dispatch_values: time = 1312380096.431; interval = 10.000; host = uml; plugin = cpu; plugin_instance = 0; type = cpu; type_instance = nice; [2011-08-03 10:01:36] uc_update: uml/memory/memory-buffered: ds[0] = 344182784.000000 [2011-08-03 10:01:36] plugin: plugin_write: Writing values via network. [2011-08-03 10:01:36] uc_update: uml/cpu-0/cpu-nice: ds[0] = 0.000000 [2011-08-03 10:01:36] plugin: plugin_write: Writing values via network. [2011-08-03 10:01:36] network plugin: flush_buffer: send_buffer_fill = 1340 [2011-08-03 10:01:36] network plugin: network_send_buffer: buffer_len = 1340 ... [2011-08-03 10:01:36] plugin_read_thread: Next read of the cpu plugin at 1312380106.429064774. collectd.log in server collectd: [2011-08-03 20:18:08] type = network [2011-08-03 20:18:08] type = rrdtool [2011-08-03 20:18:08] network plugin: sockent_open: node = 192.168.8.37; service = 25826; [2011-08-03 20:18:08] fd = 3; calling bind' [2011-08-03 20:18:08] Done parsing/opt/collectd//share/collectd/types.db' [2011-08-03 20:18:08] interval_g = 10; [2011-08-03 20:18:08] timeout_g = 2; [2011-08-03 20:18:08] hostname_g = localhost.localdomain; [2011-08-03 20:18:08] Initialization complete, entering read-loop. It looks like, data is sending but doesn't be recived. Where is the mistake?

  Read the article

• Connecting Linux to WatchGuard Firebox SSL (OpenVPN client)

  Recently, I got a new project assignment that requires to connect permanently to the customer's network through VPN. They are using a so-called SSL VPN. As I am using OpenVPN since more than 5 years within my company's network I was quite curious about their solution and how it would actually be different from OpenVPN. Well, short version: It is a disguised version of OpenVPN. Unfortunately, the company only offers a client for Windows and Mac OS which shouldn't bother any Linux user after all. OpenVPN is part of every recent distribution and can be activated in a couple of minutes - both client as well as server (if necessary). WatchGuard Firebox SSL - About dialog Borrowing some files from a Windows client installation Initially, I didn't know about the product, so therefore I went through the installation on Windows 8. No obstacles (and no restart despite installation of TAP device drivers!) here and the secured VPN channel was up and running in less than 2 minutes or so. Much appreciated from both parties - customer and me. Of course, this whole client package and my long year approved and stable installation ignited my interest to have a closer look at the WatchGuard client. Compared to the original OpenVPN client (okay, I have to admit this is years ago) this commercial product is smarter in terms of file locations during installation. You'll be able to access the configuration and key files below your roaming application data folder. To get there, simply enter '%AppData%\WatchGuard\Mobile VPN' in your Windows/File Explorer and confirm with Enter/Return. This will display the following files: Application folder below user profile with configuration and certificate files From there we are going to borrow four files, namely: ca.crt client.crt client.ovpn client.pem and transfer them to the Linux system. You might also be able to isolate those four files from a Mac OS client. Frankly, I'm just too lazy to run the WatchGuard client installation on a Mac mini only to find the folder location, and I'm going to describe why a little bit further down this article. I know that you can do that! Feedback in the comment section is appreciated. Configuration of OpenVPN (console) Depending on your distribution the following steps might be a little different but in general you should be able to get the important information from it. I'm going to describe the steps in Ubuntu 13.04 (Raring Ringtail). As usual, there are two possibilities to achieve your goal: console and UI. Let's what it is necessary to be done. First of all, you should ensure that you have OpenVPN installed on your system. Open your favourite terminal application and run the following statement: $ sudo apt-get install openvpn network-manager-openvpn network-manager-openvpn-gnome Just to be on the safe side. The four above mentioned files from your Windows machine could be copied anywhere but either you place them below your own user directory or you put them (as root) below the default directory: /etc/openvpn At this stage you would be able to do a test run already. Just in case, run the following command and check the output (it's the similar information you would get from the 'View Logs...' context menu entry in Windows: $ sudo openvpn --config client.ovpn Pay attention to the correct path to your configuration and certificate files. OpenVPN will ask you to enter your Auth Username and Auth Password in order to establish the VPN connection, same as the Windows client. Remote server and user authentication to establish the VPN Please complete the test run and see whether all went well. You can disconnect pressing Ctrl+C. Simplifying your life - authentication file In my case, I actually set up the OpenVPN client on my gateway/router. This establishes a VPN channel between my network and my client's network and allows me to switch machines easily without having the necessity to install the WatchGuard client on each and every machine. That's also very handy for my various virtualised Windows machines. Anyway, as the client configuration, key and certificate files are located on a headless system somewhere under the roof, it is mandatory to have an automatic connection to the remote site. For that you should first change the file extension '.ovpn' to '.conf' which is the default extension on Linux systems for OpenVPN, and then open the client configuration file in order to extend an existing line. $ sudo mv client.ovpn client.conf $ sudo nano client.conf You should have a similar content to this one here: dev tunclientproto tcp-clientca ca.crtcert client.crtkey client.pemtls-remote "/O=WatchGuard_Technologies/OU=Fireware/CN=Fireware_SSLVPN_Server"remote-cert-eku "TLS Web Server Authentication"remote 1.2.3.4 443persist-keypersist-tunverb 3mute 20keepalive 10 60cipher AES-256-CBCauth SHA1float 1reneg-sec 3660nobindmute-replay-warningsauth-user-pass auth.txt Note: I changed the IP address of the remote directive above (which should be obvious, right?). Anyway, the required change is marked in red and we have to create a new authentication file 'auth.txt'. You can give the directive 'auth-user-pass' any file name you'd like to. Due to my existing OpenVPN infrastructure my setup differs completely from the above written content but for sake of simplicity I just keep it 'as-is'. Okay, let's create this file 'auth.txt' $ sudo nano auth.txt and just put two lines of information in it - username on the first, and password on the second line, like so: myvpnusernameverysecretpassword Store the file, change permissions, and call openvpn with your configuration file again: $ sudo chmod 0600 auth.txt $ sudo openvpn --config client.conf This should now work without being prompted to enter username and password. In case that you placed your files below the system-wide location /etc/openvpn you can operate your VPNs also via service command like so: $ sudo service openvpn start client $ sudo service openvpn stop client Using Network Manager For newer Linux users or the ones with 'console-phobia' I'm going to describe now how to use Network Manager to setup the OpenVPN client. For this move your mouse to the systray area and click on Network Connections => VPN Connections => Configure VPNs... which opens your Network Connections dialog. Alternatively, use the HUD and enter 'Network Connections'. Network connections overview in Ubuntu Click on 'Add' button. On the next dialog select 'Import a saved VPN configuration...' from the dropdown list and click on 'Create...' Choose connection type to import VPN configuration Now you navigate to your folder where you put the client files from the Windows system and you open the 'client.ovpn' file. Next, on the tab 'VPN' proceed with the following steps (directives from the configuration file are referred): General Check the IP address of Gateway ('remote' - we used 1.2.3.4 in this setup) Authentication Change Type to 'Password with Certificates (TLS)' ('auth-pass-user') Enter User name to access your client keys (Auth Name: myvpnusername) Enter Password (Auth Password: verysecretpassword) and choose your password handling Browse for your User Certificate ('cert' - should be pre-selected with client.crt) Browse for your CA Certificate ('ca' - should be filled as ca.crt) Specify your Private Key ('key' - here: client.pem) Then click on the 'Advanced...' button and check the following values: Use custom gateway port: 443 (second value of 'remote' directive) Check the selected value of Cipher ('cipher') Check HMAC Authentication ('auth') Enter the Subject Match: /O=WatchGuard_Technologies/OU=Fireware/CN=Fireware_SSLVPN_Server ('tls-remote') Finally, you have to confirm and close all dialogs. You should be able to establish your OpenVPN-WatchGuard connection via Network Manager. For that, click on the 'VPN Connections => client' entry on your Network Manager in the systray. It is advised that you keep an eye on the syslog to see whether there are any problematic issues that would require some additional attention. Advanced topic: routing As stated above, I'm running the 'WatchGuard client for Linux' on my head-less server, and since then I'm actually establishing a secure communication channel between two networks. In order to enable your network clients to get access to machines on the remote side there are two possibilities to enable that: Proper routing on both sides of the connection which enables both-direction access, or Network masquerading on the 'client side' of the connection Following, I'm going to describe the second option a little bit more in detail. The Linux system that I'm using is already configured as a gateway to the internet. I won't explain the necessary steps to do that, and will only focus on the additional tweaks I had to do. You can find tons of very good instructions and tutorials on 'How to setup a Linux gateway/router' - just use Google. OK, back to the actual modifications. First, we need to have some information about the network topology and IP address range used on the 'other' side. We can get this very easily from /var/log/syslog after we established the OpenVPN channel, like so: $ sudo tail -n20 /var/log/syslog Or if your system is quite busy with logging, like so: $ sudo less /var/log/syslog | grep ovpn The output should contain PUSH received message similar to the following one: Jul 23 23:13:28 ios1 ovpn-client[789]: PUSH: Received control message: 'PUSH_REPLY,topology subnet,route 192.168.1.0 255.255.255.0,dhcp-option DOMAIN ,route-gateway 192.168.6.1,topology subnet,ping 10,ping-restart 60,ifconfig 192.168.6.2 255.255.255.0' The interesting part for us is the route command which I highlighted already in the sample PUSH_REPLY. Depending on your remote server there might be multiple networks defined (172.16.x.x and/or 10.x.x.x). Important: The IP address range on both sides of the connection has to be different, otherwise you will have to shuffle IPs or increase your the netmask. {loadposition content_adsense} After the VPN connection is established, we have to extend the rules for iptables in order to route and masquerade IP packets properly. I created a shell script to take care of those steps: #!/bin/sh -eIPTABLES=/sbin/iptablesDEV_LAN=eth0DEV_VPNS=tun+VPN=192.168.1.0/24 $IPTABLES -A FORWARD -i $DEV_LAN -o $DEV_VPNS -d $VPN -j ACCEPT$IPTABLES -A FORWARD -i $DEV_VPNS -o $DEV_LAN -s $VPN -j ACCEPT$IPTABLES -t nat -A POSTROUTING -o $DEV_VPNS -d $VPN -j MASQUERADE I'm using the wildcard interface 'tun+' because I have multiple client configurations for OpenVPN on my server. In your case, it might be sufficient to specify device 'tun0' only. Simplifying your life - automatic connect on boot Now, that the client connection works flawless, configuration of routing and iptables is okay, we might consider to add another 'laziness' factor into our setup. Due to kernel updates or other circumstances it might be necessary to reboot your system. Wouldn't it be nice that the VPN connections are established during the boot procedure? Yes, of course it would be. To achieve this, we have to configure OpenVPN to automatically start our VPNs via init script. Let's have a look at the responsible 'default' file and adjust the settings accordingly. $ sudo nano /etc/default/openvpn Which should have a similar content to this: # This is the configuration file for /etc/init.d/openvpn## Start only these VPNs automatically via init script.# Allowed values are "all", "none" or space separated list of# names of the VPNs. If empty, "all" is assumed.# The VPN name refers to the VPN configutation file name.# i.e. "home" would be /etc/openvpn/home.conf#AUTOSTART="all"#AUTOSTART="none"#AUTOSTART="home office"## ... more information which remains unmodified ... With the OpenVPN client configuration as described above you would either set AUTOSTART to "all" or to "client" to enable automatic start of your VPN(s) during boot. You should also take care that your iptables commands are executed after the link has been established, too. You can easily test this configuration without reboot, like so: $ sudo service openvpn restart Enjoy stable VPN connections between your Linux system(s) and a WatchGuard Firebox SSL remote server. Cheers, JoKi

  Read the article

• OpenIndiana (illumos): vmxnet3 interface lost on reboot

  - by protomouse

  I want my VMware vmxnet3 interface to be brought up with DHCP on boot. I can manually configure the NIC with: # ifconfig vmxnet3s0 plumb # ipadm create-addr -T dhcp vmxnet3s0/v4dhcp But after creating /etc/dhcp.vmxnet3s0 and rebooting, the interface is down and the logs show: Aug 13 09:34:15 neumann vmxnet3s: [ID 654879 kern.notice] vmxnet3s:0: getcapab(0x200000) -> no Aug 13 09:34:15 neumann vmxnet3s: [ID 715698 kern.notice] vmxnet3s:0: stop() Aug 13 09:34:17 neumann vmxnet3s: [ID 654879 kern.notice] vmxnet3s:0: getcapab(0x200000) -> no Aug 13 09:34:17 neumann vmxnet3s: [ID 920500 kern.notice] vmxnet3s:0: start() Aug 13 09:34:17 neumann vmxnet3s: [ID 778983 kern.notice] vmxnet3s:0: getprop(TxRingSize) -> 256 Aug 13 09:34:17 neumann vmxnet3s: [ID 778983 kern.notice] vmxnet3s:0: getprop(RxRingSize) -> 256 Aug 13 09:34:17 neumann vmxnet3s: [ID 778983 kern.notice] vmxnet3s:0: getprop(RxBufPoolLimit) -> 512 Aug 13 09:34:17 neumann nwamd[491]: [ID 605049 daemon.error] 1: nwamd_set_unset_link_properties: dladm_set_linkprop failed: operation not supported Aug 13 09:34:17 neumann vmxnet3s: [ID 654879 kern.notice] vmxnet3s:0: getcapab(0x20000) -> no Aug 13 09:34:17 neumann nwamd[491]: [ID 751932 daemon.error] 1: nwamd_down_interface: ipadm_delete_addr failed on vmxnet3s0: Object not found Aug 13 09:34:17 neumann nwamd[491]: [ID 819019 daemon.error] 1: nwamd_plumb_unplumb_interface: plumb IPv4 failed for vmxnet3s0: Operation not supported on disabled object Aug 13 09:34:17 neumann nwamd[491]: [ID 160156 daemon.error] 1: nwamd_plumb_unplumb_interface: plumb IPv6 failed for vmxnet3s0: Operation not supported on disabled object Aug 13 09:34:17 neumann nwamd[491]: [ID 771489 daemon.error] 1: add_ip_address: ipadm_create_addr failed on vmxnet3s0: Operation not supported on disabled object Aug 13 09:34:17 neumann nwamd[491]: [ID 405346 daemon.error] 9: start_dhcp: ipadm_create_addr failed for vmxnet3s0: Operation not supported on disabled object I then tried disabling network/physical:nwam in favour of network/physical:default. This works, the interface is brought up but physical:default fails and my network services (e.g. NFS) refuse to start. # ifconfig -a lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 vmxnet3s0: flags=1004843<UP,BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:1: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:2: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:3: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:4: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:5: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:6: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:7: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:8: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 lo0: flags=2002000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv6,VIRTUAL> mtu 8252 index 1 inet6 ::1/128 vmxnet3s0: flags=20002000840<RUNNING,MULTICAST,IPv6> mtu 9000 index 2 inet6 ::/0 # cat /var/svc/log/network-physical\:default.log [ Aug 16 09:46:39 Enabled. ] [ Aug 16 09:46:41 Executing start method ("/lib/svc/method/net-physical"). ] [ Aug 16 09:46:41 Timeout override by svc.startd. Using infinite timeout. ] starting DHCP on primary interface vmxnet3s0 ifconfig: vmxnet3s0: DHCP is already running [ Aug 16 09:46:43 Method "start" exited with status 96. ] NFS server not running: # svcs -xv network/nfs/server svc:/network/nfs/server:default (NFS server) State: offline since August 16, 2012 09:46:40 AM UTC Reason: Service svc:/network/physical:default is not running because a method failed. See: http://illumos.org/msg/SMF-8000-GE Path: svc:/network/nfs/server:default svc:/milestone/network:default svc:/network/physical:default Reason: Service svc:/network/physical:nwam is disabled. See: http://illumos.org/msg/SMF-8000-GE Path: svc:/network/nfs/server:default svc:/milestone/network:default svc:/network/physical:nwam Reason: Service svc:/network/nfs/nlockmgr:default is disabled. See: http://illumos.org/msg/SMF-8000-GE Path: svc:/network/nfs/server:default svc:/network/nfs/nlockmgr:default See: man -M /usr/share/man -s 1M nfsd Impact: This service is not running. I'm new to the world of Solaris, so any help solving would be much appreciated. Thanks!

  Read the article

• Event 36888 : The following fatal alert was generated: 10. The internal error state is 1203

  - by Param

  I search on the Internet, but i am unable to find, Why this error is coming? It has flooded my Event Viewer, after interval of 1 minutes, this Error pops-up. ( means the frequency is 1 minutes ) I didn't have any IIS installed. This server is purely Domain controller and no other role has been added. Please suggest, what should i do? Server OS - Window Server 2008 R2 Standard Edition More detail:- Log Name: System Source: Schannel Date: 6/28/2012 6:06:11 PM Event ID: 36888 Task Category: None Level: Error Keywords: User: SYSTEM Computer: QKSRVDC212.Corp.abc.com Description: The following fatal alert was generated: 10. The internal error state is 1203. Event Xml: 36888 0 2 0 0 0x8000000000000000 9305 System QKSRVDC212.Corp.abc.com 10 1203 Thanks & Regards, Param

  Read the article

• How can I locate all the network printers in the enterprise?

  - by AngryHacker

  When I go to Printers and Faxes dialog, I can click the Add a printer link, select Network Printer, then Find a printer in the directory. From there I get a dialog box which lets me find ALL printers in the enterprise. I need to find all the network printers with my code. How can I do this? Note that I am not talking about network printers that are connected to my PC, but all network printers in the enterprise (my workplace has almost 4000 printers). P.S. PrintServer().GetPrintQueues only returns printers attached to the computer. P.P.S. Here is a short video of what I want: http://www.angryhacker.com/toys/FindAllPrinters/FindAllPrinters.html

  Read the article

• What is the current state of development for the FLAC codec?

  - by TwentyMiles

  I have a pretty large collection of FLAC files created from my CD collection. I love the FLAC format and the sound quality that you can get from it. Lately, however, I've been trying to write a few tools to manipulate the files and I've been noticing what seems to be a stagnation of the community around the codec. Some of the links on the official FLAC page point to thing that are no longer relevant (7digital, for example, appears to no longer sell FLAC encoded songs). It's pretty hard to find hardware players that support FLAC any more (most noticeably it's not present on lower end players when it used to be, and playback is absent on Android). Programming language tools (Java and .NET libraries) are at best old, and at worst unfinished. What's the current state of FLAC development? Has it been replaced by another codec?

  Read the article

• Using ReadOnlyCollection preventing me from setting up a bi-directional many-to-many relationship

  - by Kevin Pang

  I'm using NHibernate to persist a many-to-many relation between Users and Networks. I've set up both the User and Network class as follows, exposing each's collections as ReadOnlyCollections to prevent direct access to the underlying lists. I'm trying to make sure that the only way a User can be added to a Network is by using its "JoinNetwork" function. However, I can't seem to figure out how to add the User to the Network's list of users since its collection is readonly. public class User { private ISet<Network> _Networks = new HashedSet<Network>(); public ReadOnlyCollection<Network> Networks { get { return new List<Network>(_Networks).AsReadOnly(); } } public void JoinNetwork(Network network) { _Networks.Add(network); // How do I add the current user to the Network's list of users? } } public class Network { private ISet<User> _Users = new HashedSet<User>(); public ReadOnlyCollection<User> Users { get { return new List<User>(_Users).AsReadOnly(); } } }

  Read the article

• Multiple Graphics2D Objects

  - by Trizicus

  I have a Graphics object of JPanel and that is working fine: import java.awt.Color; import java.awt.Graphics; import java.awt.Graphics2D; import java.awt.geom.Rectangle2D; import javax.swing.JPanel; public class GraphicsTest extends JPanel { private Graphics2D g2d; private String state; private int x, y; @Override public void paintComponent(Graphics g) { super.paintComponent(g); g2d = (Graphics2D) g; g2d.setClip(0, 0, getWidth(), getHeight()); g2d.setColor(Color.BLACK); g2d.drawString("STATE: " + state, 5, 15); g2d.drawString("Mouse Position: " + x + ", " + y, 5, 30); g2d.setColor(Color.red); Rectangle2D r2d = new Rectangle2D.Double(x,y,10,10); g2d.draw(r2d); Test t = new Test(); super.add(t); repaint(); } public void setState(String state) { this.state = state; } public String getState() { return state; } public void setX(int x) { this.x = x; } public void setY(int y) { this.y = y; } } I was experimenting with a new Graphics component and when I instantiate a new Test and add it in GraphicsTest nothing happens. What is it that I am doing wrong? import java.awt.Color; import java.awt.Graphics; import java.awt.Graphics2D; import java.awt.geom.Rectangle2D; import javax.swing.JComponent; public class Test extends JComponent { private Graphics2D g2d; private String state; private int x, y; @Override public void paintComponent(Graphics g) { super.paintComponent(g); g2d = (Graphics2D) g.create(); g2d.setColor(Color.GREEN); g2d.fill(new Rectangle2D.Double(60, 60, 10, 10)); repaint(); } public void setState(String state) { this.state = state; } public String getState() { return state; } public void setX(int x) { this.x = x; } public void setY(int y) { this.y = y; } } Thanks!

  Read the article

• Code refactoring homework?

  - by Hira

  This is the code that I have to refactor for my homework: if (state == TEXAS) { rate = TX_RATE; amt = base * TX_RATE; calc = 2 * basis(amt) + extra(amt) * 1.05; } else if ((state == OHIO) || (state == MAINE)) { rate = (state == OHIO) ? OH_RATE : MN_RATE; amt = base * rate; calc = 2 * basis(amt) + extra(amt) * 1.05; if (state == OHIO) points = 2; } else { rate = 1; amt = base; calc = 2 * basis(amt) + extra(amt) * 1.05; } I have done something like this if (state == TEXAS) { rate = TX_RATE; calculation(rate); } else if ((state == OHIO) || (state == MAINE)) { rate = (state == OHIO) ? OH_RATE : MN_RATE; calculation(rate); if (state == OHIO) points = 2; } else { rate = 1; calculation(rate); } function calculation(rate) { amt = base * rate; calc = 2 * basis(amt) + extra(amt) * 1.05; } How could I have done better? Edit i have done code edit amt = base * rate;

  Read the article

• Fluent NHibernate Many to one mapping

  - by Jit

  I am creating a NHibenate application with one to many relationship. Like City and State data. City table CREATE TABLE [dbo].[State]( [StateId] [varchar](2) NOT NULL primary key, [StateName] [varchar](20) NULL) CREATE TABLE [dbo].[City]( [Id] [int] primary key IDENTITY(1,1) NOT NULL , [State_id] [varchar](2) NULL refrences State(StateId), [CityName] [varchar](50) NULL) My mapping is follows public CityMapping() { Id(x = x.Id); Map(x = x.State_id); Map(x = x.CityName); HasMany(x = x.EmployeePreferedLocations) .Inverse() .Cascade.SaveUpdate() ; References(x = x.State) //.Cascade.All(); //.Class(typeof(State)) //.Not.Nullable() .Cascade.None() .Column("State_id") ; } public StateMapping() { Id(x => x.StateId) .GeneratedBy.Assigned(); Map(x => x.StateName); HasMany(x => x.Jobs) .Inverse(); //.Cascade.SaveUpdate(); HasMany(x => x.EmployeePreferedLocations) .Inverse(); HasMany(x => x.Cities) // .Inverse() .Cascade.SaveUpdate() //.Not.LazyLoad() ; } Models are as follows: [Serializable] public partial class City { public virtual System.String CityName { get; set; } public virtual System.Int32 Id { get; set; } public virtual System.String State_id { get; set; } public virtual IList<EmployeePreferedLocation> EmployeePreferedLocations { get; set; } public virtual JobPortal.Data.Domain.Model.State State { get; set; } public City(){} } public partial class State { public virtual System.String StateId { get; set; } public virtual System.String StateName { get; set; } public virtual IList<City> Cities { get; set; } public virtual IList<EmployeePreferedLocation> EmployeePreferedLocations { get; set; } public virtual IList<Job> Jobs { get; set; } public State() { Cities = new List<City>(); EmployeePreferedLocations = new List<EmployeePreferedLocation>(); Jobs = new List<Job>(); } //public virtual void AddCity(City city) //{ // city.State = this; // Cities.Add(city); //} } My Unit Testing code is below. City city = new City(); IRepository<State> rState = new Repository<State>(); Dictionary<string, string> critetia = new Dictionary<string, string>(); critetia.Add("StateId", "TX"); State frState = rState.GetByCriteria(critetia); city.CityName = "Waco"; city.State = frState; IRepository<City> rCity = new Repository<City>(); rCity.SaveOrUpdate(city); City frCity = rCity.GetById(city.Id); The problem is , I am not able to insert record. The error is below. "Invalid index 2 for this SqlParameterCollection with Count=2." But the error will not come if I comment State_id mapping field in the CityMapping file. I donot know what mistake is I did. If do not give the mapping Map(x = x.State_id); the value of this field is null, which is desired. Please help me how to solve this issue.

  Read the article

• Can't figure out how to list all the people that don't live in same City as...

  - by AspOnMyNet

  I’d like to list all the people ( Person table ) that don’t live in same city as those cities listed in Location table. Thus, if Location table holds a record with City=’New York’ and State=’Moon’, but Person table holds a record with FirstName=’Someone’, City=’New York’ and Location=’Mars’, then Someone is listed in the resulting set, since she lives in New York located on Mars and not New York located on Moon, thus we’re talking about different cities with the same name. I tried solving it with the following query, but results are wrong: SELECT Person.FirstName, Person.LastName, Person.City, Person.State FROM Person INNER JOIN Location ON (Person.City <> Location.City AND Person.State = Location.State) OR (Person.City = Location.City AND Person.State <> Location.State) OR (Person.City <> Location.City AND Person.State <> Location.State) ORDER BY Person.LastName; Any ideas?

  Read the article

• Setup routing and iptables for new VPN connection to redirect **only** ports 80 and 443

  - by Steve

  I have a new VPN connection (using openvpn) to allow me to route around some ISP restrictions. Whilst it is working fine, it is taking all the traffic over the vpn. This is causing me issues for downloading (my internet connection is a lot faster than the vpn allows), and for remote access. I run an ssh server, and have a daemon running that allows me to schdule downloads via my phone. I have my existing ethernet connection on eth0, and the new VPN connection on tun0. I believe I need to setup the default route to use my existing eth0 connection on the 192.168.0.0/24 network, and set the default gateway to 192.168.0.1 (my knowledge is shaky as I haven't done this for a number of years). If that is correct, then I'm not exactly sure how to do it!. My current routing table is: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface MSS Window irtt 0.0.0.0 10.51.0.169 0.0.0.0 UG 0 0 0 tun0 0 0 0 10.51.0.1 10.51.0.169 255.255.255.255 UGH 0 0 0 tun0 0 0 0 10.51.0.169 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 0 0 0 85.25.147.49 192.168.0.1 255.255.255.255 UGH 0 0 0 eth0 0 0 0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 eth0 0 0 0 192.168.0.0 0.0.0.0 255.255.255.0 U 1 0 0 eth0 0 0 0 After fixing the routing, I believe I need to use iptables to configure prerouting or masquerading to force everything for destination port 80 or 443 over tun0. Again, I'm not exactly sure how to do this! Everything I've found on the internet is trying to do something far more complicated, and trying to sort the wood from the trees is proving difficult. Any help would be much appreciated. UPDATE So far, from the various sources, I've cobbled together the following: #!/bin/sh DEV1=eth0 IP1=`ifconfig|perl -nE'/dr:(\S+)/&&say$1'|grep 192.` GW1=192.168.0.1 TABLE1=internet TABLE2=vpn DEV2=tun0 IP2=`ifconfig|perl -nE'/dr:(\S+)/&&say$1'|grep 10.` GW2=`route -n | grep 'UG[ \t]' | awk '{print $2}'` ip route flush table $TABLE1 ip route flush table $TABLE2 ip route show table main | grep -Ev ^default | while read ROUTE ; do ip route add table $TABLE1 $ROUTE ip route add table $TABLE2 $ROUTE done ip route add table $TABLE1 $GW1 dev $DEV1 src $IP1 ip route add table $TABLE2 $GW2 dev $DEV2 src $IP2 ip route add table $TABLE1 default via $GW1 ip route add table $TABLE2 default via $GW2 echo "1" > /proc/sys/net/ipv4/ip_forward echo "1" > /proc/sys/net/ipv4/ip_dynaddr ip rule add from $IP1 lookup $TABLE1 ip rule add from $IP2 lookup $TABLE2 ip rule add fwmark 1 lookup $TABLE1 ip rule add fwmark 2 lookup $TABLE2 iptables -t nat -A POSTROUTING -o $DEV1 -j SNAT --to-source $IP1 iptables -t nat -A POSTROUTING -o $DEV2 -j SNAT --to-source $IP2 iptables -t nat -A PREROUTING -m state --state ESTABLISHED,RELATED -j CONNMARK --restore-mark iptables -A OUTPUT -m state --state ESTABLISHED,RELATED -j CONNMARK --restore-mark iptables -t nat -A PREROUTING -i $DEV1 -m state --state NEW -j CONNMARK --set-mark 1 iptables -t nat -A PREROUTING -i $DEV2 -m state --state NEW -j CONNMARK --set-mark 2 iptables -t nat -A PREROUTING -m connmark --mark 1 -j MARK --set-mark 1 iptables -t nat -A PREROUTING -m connmark --mark 2 -j MARK --set-mark 2 iptables -t nat -A PREROUTING -m state --state NEW -m connmark ! --mark 0 -j CONNMARK --save-mark iptables -t mangle -A PREROUTING -i $DEV2 -m state --state NEW -p tcp --dport 80 -j CONNMARK --set-mark 2 iptables -t mangle -A PREROUTING -i $DEV2 -m state --state NEW -p tcp --dport 443 -j CONNMARK --set-mark 2 route del default route add default gw 192.168.0.1 eth0 Now this seems to be working. Except it isn't! Connections to the blocked websites are going through, connections not on ports 80 and 443 are using the non-VPN connection. However port 80 and 443 connections that aren't to the blocked websites are using the non-VPN connection too! As the general goal has been reached, I'm relatively happy, but it would be nice to know why it isn't working exactly right. Any ideas? For reference, I now have 3 routing tables, main, internet, and vpn. The listing of them is as follows... Main: default via 192.168.0.1 dev eth0 10.38.0.1 via 10.38.0.205 dev tun0 10.38.0.205 dev tun0 proto kernel scope link src 10.38.0.206 85.removed via 192.168.0.1 dev eth0 169.254.0.0/16 dev eth0 scope link metric 1000 192.168.0.0/24 dev eth0 proto kernel scope link src 192.168.0.73 metric 1 Internet: default via 192.168.0.1 dev eth0 10.38.0.1 via 10.38.0.205 dev tun0 10.38.0.205 dev tun0 proto kernel scope link src 10.38.0.206 85.removed via 192.168.0.1 dev eth0 169.254.0.0/16 dev eth0 scope link metric 1000 192.168.0.0/24 dev eth0 proto kernel scope link src 192.168.0.73 metric 1 192.168.0.1 dev eth0 scope link src 192.168.0.73 VPN: default via 10.38.0.205 dev tun0 10.38.0.1 via 10.38.0.205 dev tun0 10.38.0.205 dev tun0 proto kernel scope link src 10.38.0.206 85.removed via 192.168.0.1 dev eth0 169.254.0.0/16 dev eth0 scope link metric 1000 192.168.0.0/24 dev eth0 proto kernel scope link src 192.168.0.73 metric 1

  Read the article

• What possible events could cause a MySQL database to revert to a previous state?

  - by justkevin

  A client of mine recently had a strange event with their MySQL database. Several days ago, one database suddenly "went back in time". All the data was in the state it was in several months ago. Even most of the .MYD and .MYI files had timestamps from November. Fortunately, the server is not in production yet, but we need to understand how it happened so it doesn't happen again. I'm not a MySQL guru, but I couldn't think of a scenario that could cause the database to rewind like that short of restoring from a backup. What could have happened here? Where should I look for clues? (Server is FreeBSD 6.4)

  Read the article

• How do I impliment a hidden field in a post form so users can't accidentally double post? (PHP/Mysql

  - by ggfan

  When users submit a form, they will sometimes click refresh or backspace then resubmit which causes multiple entries in mysql. How can i prevent mysql from allowing more than 1 of the same entry? People suggested a hidden field with a value, but how do I use that? <label for="state" class="styled">State:</label> <input type="text" id="state" name="state" value="<?php if (!empty($state)) echo $state; ?>" size="30" /><br /> //a hidden field of a certain value? ________________________________________ <input type="submit" value="Post Ad!" name="submit" /> //php to insert to mysql $query4 = "INSERT INTO posting (state) VALUES ('$state')"; mysqli_query($dbc, $query4);

  Read the article

• Raphael.js map default fill colors

  - by RIDER

  I am trying to familiarize myself with raphael.js. I want to create a USA map that already has default colors for each state and those colors stay there. Here is what I came up with. If you look at AK, I'm getting the default color loaded, but if I highlight another state, the default color for AK disappears. I want AK - and other states - to stay the same color. Specifically, I don't know what is clearing out my AK full color. I think part of this statement is clearing out the fill cover when I mouseover a different state: for (var state in aus) { //aus[state].color = Raphael.getColor(); (function (st, state) { st[0].style.cursor = "pointer"; st[0].onmouseover = function () { current && aus[current].animate({fill: "#333", stroke: "#666"}, 500) && (document.getElementById(current).style.display = ""); st.animate({fill: st.color, stroke: "#ccc"}, 500); st.toFront(); R.safari(); document.getElementById(state).style.display = "block"; current = state; }; })(aus[state], state); } Any ideas where I might be going wrong?

  Read the article

• How to force Weblogic to start deployments in active state (i.e. not just prepared)

  - by doublep

  When I start a Weblogic instance with a deployed application, the deployment is sometimes left in prepared state, not in active state. I have to go to Weblogic Console and start the deployment manually, which is quite slow and annoying repetetive work. Since this is done on a development machine — sometimes 50 times a day, — there are no security implication as the server is only visible on the local network. Is there some way to have it always start the deployment active? Note that I'm not redeploying the application, I instead have it "constantly deployed" and stop/start the Weblogic instance using the scripts in bin directory.

  Read the article

• Change the state of a customized button (button with an image)?

  - by Harry Pham

  I know how to change the state of the regular button, as well as change the background color of a regular button. However, what I have is a image lay on top of a button (customized button). I want, when the user click on it, something visually would happen to let the user know that button is selected, and when the user click again it go back to the regular state. I try to change the background of the button, but it doesnt work since the image kind of cover the button. Any idea?

  Read the article

• How do I create a custom network connection entry?

  - by David Brown

  I have a Sprint MiFi 3G router that exposes its current signal strength over HTTP. I've developed a very simple tray application that displays this. However, what I would really like to do is create a custom network connection entry so the router's 3G signal strength (along with the current network version) displays when clicking on the network connections tray icon (in Windows 7, at least). Is it possible to do this with a shell extension or something (preferably in C#)? If so, how?

  Read the article

• What's causing "shutdown state" after TFTP reloaded Cisco `running-config` on 871?

  - by xtian

  Cisco CCP Write Configuration borked my 871w config while I was trying to setup port forwarding. I tested the 871's flash memory with fsck and rewrote the minimal config for TFTP (which is the same for Cisco's CCP app.). Thne, I successfully uploaded a previously working running-config from Win Vista using SolarWinds TFTP Server, unfortunately the restore was not entirely successful. The old running config was saved to the 871's startup-config and I can login using console port. Some other things that are working are the hostname and welcome message but that's about it. Startup shows an error SETUP: new interface NVI0 placed in "shutdown" state after tftp. The missing light on the access point modem for ethernet link show the 871'a outside FE4 is not working. SO...what's the possible problem with reloading a previously working config (approximately 4 months with the same config) via TFTP? Is there something I can look for on the 871 to verify the config?

  Read the article

• How do I tell if my solid state hard disk is bad?

  - by Guy

  I have a Windows 7 Ultimate computer (Shuttle) that I built myself and in it I put a Solid State Drive (SSD). It's been working well for a number of months but now when I start it there are problems. I have 2 users setup on the computer and when I try and sign in with either user it claims that the password is incorrect. I could understand the odd typo but I've had my wife try it as well and we've got the passwords correct. On top of that it will remain at the login screen for 1 minute and 20 seconds and then spontaneously reboot without shutting down. So I'm trying to work out if this is a hard disk problem or something else. Any ideas? (I have a nightly backup to a WHS so it will be easy to recover but I don't want to do that unless I have to and don't want to waste time putting in a new HD just to discover it's something else.)

  Read the article

< Previous Page | 207 208 209 210 211 212 213 214 215 216 217 218  | Next Page >