Search Results

Search found 7249 results on 290 pages for 'executive messages'.

Page 212/290 | < Previous Page | 208 209 210 211 212 213 214 215 216 217 218 219  | Next Page >

• How to set shmall, shmmax, shmni, etc ... in general and for postgresql

  - by jpic

  I've used the documentation from PostgreSQL to set it for example this config: >>> cat /proc/meminfo MemTotal: 16345480 kB MemFree: 1770128 kB Buffers: 382184 kB Cached: 10432632 kB SwapCached: 0 kB Active: 9228324 kB Inactive: 4621264 kB Active(anon): 7019996 kB Inactive(anon): 548528 kB Active(file): 2208328 kB Inactive(file): 4072736 kB Unevictable: 0 kB Mlocked: 0 kB SwapTotal: 0 kB SwapFree: 0 kB Dirty: 3432 kB Writeback: 0 kB AnonPages: 3034588 kB Mapped: 4243720 kB Shmem: 4533752 kB Slab: 481728 kB SReclaimable: 440712 kB SUnreclaim: 41016 kB KernelStack: 1776 kB PageTables: 39208 kB NFS_Unstable: 0 kB Bounce: 0 kB WritebackTmp: 0 kB CommitLimit: 8172740 kB Committed_AS: 14935216 kB VmallocTotal: 34359738367 kB VmallocUsed: 399340 kB VmallocChunk: 34359334908 kB HardwareCorrupted: 0 kB AnonHugePages: 456704 kB HugePages_Total: 0 HugePages_Free: 0 HugePages_Rsvd: 0 HugePages_Surp: 0 Hugepagesize: 2048 kB DirectMap4k: 12288 kB DirectMap2M: 16680960 kB >>> ipcs -l ------ Shared Memory Limits -------- max number of segments = 4096 max seg size (kbytes) = 4316816 max total shared memory (kbytes) = 4316816 min seg size (bytes) = 1 ------ Semaphore Limits -------- max number of arrays = 128 max semaphores per array = 250 max semaphores system wide = 32000 max ops per semop call = 32 semaphore max value = 32767 ------ Messages Limits -------- max queues system wide = 31918 max size of message (bytes) = 8192 default max size of queue (bytes) = 16384 sysctl.conf extract: kernel.shmall = 1079204 kernel.shmmax = 4420419584 postgresql.conf non defaults: max_connections = 60 # (change requires restart) shared_buffers = 4GB # min 128kB work_mem = 4MB # min 64kB wal_sync_method = open_sync # the default is the first option checkpoint_segments = 16 # in logfile segments, min 1, 16MB each checkpoint_completion_target = 0.9 # checkpoint target duration, 0.0 - 1.0 effective_cache_size = 6GB Is this appropriate ? If not (or not necessarily), in which case would it be appropriate ? We did note nice performance improvements with this config, how would you improve it ? How should kernel memory management parameters be set ? Can anybody explain how to really set them from the ground up ?

  Read the article

• TS (RD) Gateway Authentication Problem "The logon attempt failed"

  - by user2059

  I've been using TS Gateway to permit remote access for our staff for a few months now, and all has been well. Users either connect to a traditional terminal server desktop or hit our website and start an TS RemoteApp application- in both cases the connection is routed through a TS Gateway. However I came into work this morning to find that has stopped authenticating users through TS Gateway, each time returning "The logon attempt failed" as seen in the image even though the credentials are correct. It should be noted that everything works fine if the Gateway is taken out of the equation, it's the TS Gateway component that is causing these problems. Users experience this problem whether they connect through XP SP3, Vista or 7. On the server a total of 4 entries appear in the Windows security log at exactly the same time for each failed logon attempt: two 4624 "An account was successfully logged on" messages for the user, immediately followed by two 4634 "An account was logged off"s. This suggests that the server is accepting the credentials as correct, then booting the user off. Nothing at all is recorded in the NPS and Terminal Server logs. A reboot doesn't change things. Neither does completely removing and reinstalling the NPS and Terminal Server roles. I'm baffled as to how this can happen suddenly without warning. Any suggestions would be greatly appreciated.

  Read the article

• Server compromised. Bounce message contains many email addresses message was not sent to

  - by Tim Duncklee

  This is not a dupe. Please read and understand the issue before marking this as a duplicate question that has been answered already. Several customers are reporting bounce messages like the one below. At first I thought their computers had a virus but then I received one that was server generated so the problem is with the server. I've inspected the logs and these email addresses do not appear in the logs. The only thing I see that I do not remember seeing in the past are entries like this: Apr 30 13:34:49 psa86 qmail-queue-handlers[20994]: hook_dir = '/var/qmail//handlers/before-queue' Apr 30 13:34:49 psa86 qmail-queue-handlers[20994]: recipient[3] = '[email protected]' Apr 30 13:34:49 psa86 qmail-queue-handlers[20994]: handlers dir = '/var/qmail//handlers/before-queue/recipient/[email protected]' I've searched here and the web and maybe I'm just not entering the right search terms but I find nothing on this issue. Does anyone know how a hacker would attach additional email addresses to a message at the server and have them not appear in the logs? CentOS release 5.4, Plesk 8.6, QMail 1.03 Hi. This is the qmail-send program at psa.aaaaaa.com. I'm afraid I wasn't able to deliver your message to the following addresses. This is a permanent error; I've given up. Sorry it didn't work out. <[email protected]>: 82.201.133.227 does not like recipient. Remote host said: 550 #5.1.0 Address rejected. Giving up on 82.201.133.227. <[email protected]>: 64.18.7.10 does not like recipient. Remote host said: 550 No such user - psmtp Giving up on 64.18.7.10. <[email protected]>: 173.194.68.27 does not like recipient. Remote host said: 550-5.1.1 The email account that you tried to reach does not exist. Please try 550-5.1.1 double-checking the recipient's email address for typos or 550-5.1.1 unnecessary spaces. Learn more at 550 5.1.1 http://support.google.com/mail/bin/answer.py?answer=6596 w8si1903qag.18 - gsmtp Giving up on 173.194.68.27. <[email protected]>: 207.115.36.23 does not like recipient. Remote host said: 550 5.2.1 <[email protected]>... Addressee unknown, relay=[174.142.62.210] Giving up on 207.115.36.23. <[email protected]>: 207.115.37.22 does not like recipient. Remote host said: 550 5.2.1 <[email protected]>... Addressee unknown, relay=[174.142.62.210] Giving up on 207.115.37.22. <[email protected]>: 207.115.37.20 does not like recipient. Remote host said: 550 5.2.1 <[email protected]>... Addressee unknown, relay=[174.142.62.210] Giving up on 207.115.37.20. <[email protected]>: 207.115.37.23 does not like recipient. Remote host said: 550 5.2.1 <[email protected]>... Addressee unknown, relay=[174.142.62.210] Giving up on 207.115.37.23. <[email protected]>: 207.115.36.22 does not like recipient. Remote host said: 550 5.2.1 <[email protected]>... Addressee unknown, relay=[174.142.62.210] Giving up on 207.115.36.22. <[email protected]>: 74.205.16.140 does not like recipient. Remote host said: 553 sorry, that domain isn't in my list of allowed rcpthosts; no valid cert for gatewaying (#5.7.1) Giving up on 74.205.16.140. <[email protected]>: 207.115.36.20 does not like recipient. Remote host said: 550 5.2.1 <[email protected]>... Addressee unknown, relay=[174.142.62.210] Giving up on 207.115.36.20. <[email protected]>: 207.115.37.21 does not like recipient. Remote host said: 550 5.2.1 <[email protected]>... Addressee unknown, relay=[174.142.62.210] Giving up on 207.115.37.21. <[email protected]>: 192.169.41.23 failed after I sent the message. Remote host said: 554 qq Sorry, no valid recipients (#5.1.3) --- Below this line is a copy of the message. Return-Path: <[email protected]> Received: (qmail 15962 invoked from network); 1 May 2013 06:49:34 -0400 Received: from exprod6mo107.postini.com (64.18.1.18) by psa.aaaaaa.com with (DHE-RSA-AES256-SHA encrypted) SMTP; 1 May 2013 06:49:34 -0400 Received: from aaaaaa.com (exprod6lut001.postini.com [64.18.1.199]) by exprod6mo107.postini.com (Postfix) with SMTP id 47F80B8CA4 for <[email protected]>; Wed, 1 May 2013 03:49:33 -0700 (PDT) From: "Support" <[email protected]> To: [email protected] Subject: Detected Potential Junk Mail Date: Wed, 1 May 2013 03:49:33 -0700 Dear [email protected], junk mail protection service has detected suspicious email message(s) since your last visit and directed them to your Message Center. You can inspect your suspicious email at: ... UPDATE: After not seeing this problem for a while, I personally sent a message and immediately got a bounce with several bad addresses that I know I did not send to. These are addresses that are not on my system or on the server. This problem happens with both Mac and Windows clients and with messages generated from Postini and sent to users on my system. This is NOT backscatter. If it was backscatter it would not have the contents of my message in it. UPDATE #2 Here is another bounce. This one was sent by me and the bounce came back immediately. Hi. This is the qmail-send program at psa.aaaaaa.com. I'm afraid I wasn't able to deliver your message to the following addresses. This is a permanent error; I've given up. Sorry it didn't work out. <[email protected]>: 71.74.56.227 does not like recipient. Remote host said: 550 5.1.1 <[email protected]>... User unknown Giving up on 71.74.56.227. <[email protected]>: Connected to 208.34.236.3 but sender was rejected. Remote host said: 550 5.7.1 This system is configured to reject mail from 174.142.62.210 [174.142.62.210] (Host blacklisted - Found on Realtime Black List server 'bl.mailspike.net') <[email protected]>: 66.96.80.22 failed after I sent the message. Remote host said: 552 sorry, mailbox [email protected] is over quota temporarily (#5.1.1) <[email protected]>: 83.145.109.52 does not like recipient. Remote host said: 550 5.1.1 <[email protected]>: Recipient address rejected: User unknown in virtual mailbox table Giving up on 83.145.109.52. <[email protected]>: 69.49.101.234 does not like recipient. Remote host said: 550 5.7.1 <[email protected]>... H:M12 [174.142.62.210] Connection refused due to abuse. Please see http://mailspike.org/anubis/lookup.html or contact your E-mail provider. Giving up on 69.49.101.234. <[email protected]>: 212.55.154.36 does not like recipient. Remote host said: 550-The account has been suspended for inactivity 550 A conta do destinatario encontra-se suspensa por inactividade (#5.2.1) Giving up on 212.55.154.36. <[email protected]>: 199.168.90.102 failed after I sent the message. Remote host said: 552 Transaction [email protected] failed, remote said "550 No such user" (#5.1.1) <[email protected]>: 98.136.217.192 failed after I sent the message. Remote host said: 554 delivery error: dd Sorry your message to [email protected] cannot be delivered. This account has been disabled or discontinued [#102]. - mta1210.sbc.mail.gq1.yahoo.com --- Below this line is a copy of the message. Return-Path: <[email protected]> Received: (qmail 2618 invoked from network); 2 Jun 2013 22:32:51 -0400 Received: from 75-138-254-239.dhcp.jcsn.tn.charter.com (HELO ?192.168.0.66?) (75.138.254.239) by psa.aaaaaa.com with SMTP; 2 Jun 2013 22:32:48 -0400 User-Agent: Microsoft-Entourage/12.34.0.120813 Date: Sun, 02 Jun 2013 21:32:39 -0500 Subject: Refinance From: Tim Duncklee <[email protected]> To: Scott jones <[email protected]> Message-ID: <CDD16A79.67344%[email protected]> Thread-Topic: Reference Thread-Index: Ac5gAp2QmTs+LRv0SEOy7AJTX2DWzQ== Mime-version: 1.0 Content-type: multipart/mixed; boundary="B_3453053568_12034440" > This message is in MIME format. Since your mail reader does not understand this format, some or all of this message may not be legible. --B_3453053568_12034440 Content-type: multipart/related; boundary="B_3453053568_11982218" --B_3453053568_11982218 Content-type: multipart/alternative; boundary="B_3453053568_12000660" --B_3453053568_12000660 Content-type: text/plain; charset="ISO-8859-1" Content-transfer-encoding: quoted-printable Scott, ... email body here ... Here are the relevant log entries: Jun 2 22:32:50 psa qmail-queue[2616]: mail: all addreses are uncheckable - need to skip scanning (by deny mode) Jun 2 22:32:50 psa qmail-queue[2616]: scan: the message(drweb.tmp.i2SY0n) sent by [email protected] to [email protected] should be passed without checks, because contains uncheckable addresses Jun 2 22:32:50 psa qmail-queue-handlers[2617]: Handlers Filter before-queue for qmail started ... Jun 2 22:32:50 psa qmail-queue-handlers[2617]: [email protected] Jun 2 22:32:50 psa qmail-queue-handlers[2617]: [email protected] Jun 2 22:32:50 psa qmail-queue-handlers[2617]: hook_dir = '/var/qmail//handlers/before-queue' Jun 2 22:32:50 psa qmail-queue-handlers[2617]: recipient[3] = '[email protected]' Jun 2 22:32:50 psa qmail-queue-handlers[2617]: handlers dir = '/var/qmail//handlers/before-queue/recipient/[email protected]' Jun 2 22:32:51 psa qmail: 1370226771.060211 starting delivery 57: msg 1540285 to remote [email protected] Jun 2 22:32:51 psa qmail: 1370226771.060402 status: local 0/10 remote 1/20 Jun 2 22:32:51 psa qmail: 1370226771.060556 new msg 4915232 Jun 2 22:32:51 psa qmail: 1370226771.060671 info msg 4915232: bytes 687899 from <[email protected]> qp 2618 uid 2020 Jun 2 22:32:51 psa qmail-remote-handlers[2619]: Handlers Filter before-remote for qmail started ... Jun 2 22:32:51 psa qmail-queue-handlers[2617]: starter: submitter[2618] exited normally Jun 2 22:32:51 psa qmail-remote-handlers[2619]: from= Jun 2 22:32:51 psa qmail-remote-handlers[2619]: [email protected] Jun 2 22:32:51 psa qmail: 1370226771.078732 starting delivery 58: msg 4915232 to remote [email protected] Jun 2 22:32:51 psa qmail: 1370226771.078825 status: local 0/10 remote 2/20 Jun 2 22:32:51 psa qmail-remote-handlers[2621]: Handlers Filter before-remote for qmail started ... Jun 2 22:32:51 psa qmail-remote-handlers[2621]: [email protected] Jun 2 22:32:51 psa qmail-remote-handlers[2621]: [email protected]

  Read the article

• Prosody mod auth external not working

  - by Yang

  I installed mod_auth_external for 0.8.2 on ubuntu 12.04 but it's not working. I have external_auth_command = "/home/yang/chat/testing" but it's not getting invoked. I enabled debug logging and see no messages from that mod. Any help? I'm using the Candy example client. Here's what's written to the log after I submit a login request (and nothing in err log): Oct 24 21:02:43 socket debug server.lua: accepted new client connection from 127.0.0.1:40527 to 5280 Oct 24 21:02:43 mod_bosh debug BOSH body open (sid: %s) Oct 24 21:02:43 boshb344ba85-fbf5-4a26-b5f5-5bd35d5ed372 debug BOSH session created for request from 169.254.11.255 Oct 24 21:02:43 mod_bosh info New BOSH session, assigned it sid 'b344ba85-fbf5-4a26-b5f5-5bd35d5ed372' Oct 24 21:02:43 httpserver debug Sending response to bf9120 Oct 24 21:02:43 httpserver debug Destroying request bf9120 Oct 24 21:02:43 httpserver debug Request has destroy callback Oct 24 21:02:43 socket debug server.lua: closed client handler and removed socket from list Oct 24 21:02:43 mod_bosh debug Session b344ba85-fbf5-4a26-b5f5-5bd35d5ed372 has 0 out of 1 requests open Oct 24 21:02:43 mod_bosh debug and there are 0 things in the send_buffer Oct 24 21:02:43 socket debug server.lua: accepted new client connection from 127.0.0.1:40528 to 5280 Oct 24 21:02:43 mod_bosh debug BOSH body open (sid: b344ba85-fbf5-4a26-b5f5-5bd35d5ed372) Oct 24 21:02:43 mod_bosh debug Session b344ba85-fbf5-4a26-b5f5-5bd35d5ed372 has 1 out of 1 requests open Oct 24 21:02:43 mod_bosh debug and there are 0 things in the send_buffer Oct 24 21:02:43 mod_bosh debug Have nothing to say, so leaving request unanswered for now Oct 24 21:02:43 httpserver debug Request c295d0 left open, on_destroy is function(mod_bosh.lua:81) Here's the config I added: modules_enabled = { ... "bosh"; -- Enable BOSH clients, aka "Jabber over HTTP" ... } authentication = "external" external_auth_protocol = "generic" external_auth_command = "/home/yang/chat/testing"

  Read the article

• Clamav. WARNING: No clamd server appears to be available

  - by Jevgeni Smirnov

  I have clamav.log full of these messages, what might be the problem and how to fix this? I have Debian clamav-0.97.6+dfsg-1~squeeze1 spamassassin-3.3.1-1 dovecot-pop3d-1.2.15-7 postfix-2.7.1-1+squeeze1 and also there is somewhere near milter. LocalSocket setting is ok Tue Jun 4 07:43:34 2013 -> WARNING: No clamd server appears to be available Tue Jun 4 07:44:34 2013 -> WARNING: No clamd server appears to be available Tue Jun 4 07:45:34 2013 -> WARNING: No clamd server appears to be available Tue Jun 4 07:46:34 2013 -> WARNING: No clamd server appears to be available Tue Jun 4 07:47:34 2013 -> WARNING: No clamd server appears to be available Tue Jun 4 07:47:58 2013 -> ERROR: Failed to initiate streaming/fdpassing Tue Jun 4 07:47:58 2013 -> WARNING: No clamd server appears to be available Tue Jun 4 07:48:58 2013 -> WARNING: No clamd server appears to be available Tue Jun 4 07:49:33 2013 -> ERROR: Failed to initiate streaming/fdpassing Tue Jun 4 07:49:33 2013 -> WARNING: No clamd server appears to be available

  Read the article

• Oracle® Database Express Edition roblem running on Win Server 2003 with MS SQl Server 2008 [closed]

  - by totoz

  Hi I have on Win Server 2003 MS SQL Server 2008 and also IIS is running. I try learn Oracle, so first I installed Oracle® Database Express Edition. I tried connect viac web browser on Oracle Server on url http://127.0.0.1:8080/apex I got this expcetion in browser The page cannot be found The page you are looking for might have been removed, had its name changed, or is temporarily unavailable. Please try the following: Make sure that the Web site address displayed in the address bar of your browser is spelled and formatted correctly. If you reached this page by clicking a link, contact the Web site administrator to alert them that the link is incorrectly formatted. Click the Back button to try another link. HTTP Error 404 - File or directory not found. Internet Information Services (IIS) Technical Information (for support personnel) Go to Microsoft Product Support Services and perform a title search for the words HTTP and 404. Open IIS Help, which is accessible in IIS Manager (inetmgr), and search for topics titled Web Site Setup, Common Administrative Tasks, and About Custom Error Messages. Why I can not log on Oracle Home Page?

  Read the article

• Postfix mail server: can't connect via POP/IMAP

  - by MelkerOVan

  I've followed this guide on setting up a mail server on my dedicated server. I've been able to send mails from the php application I'm using and the linux commandline (using telnet, php, etc). The problem is that I cannot connect to the server via IMAP/POP which I've setup using Courier. I've tried using thunderbird but it complains that the username or password is wrong. I doubt it is the username/password but I don't know how to trouble shoot this. Edit: Here's the messages in mail.log: Jan 9 22:43:38 mail authdaemond: received auth request, service=imap, authtype=login Jan 9 22:43:38 mail authdaemond: authmysql: trying this module Jan 9 22:43:38 mail authdaemond: SQL query: SELECT id, crypt, "", uid, gid, home, "", "", name, "" FROM users WHERE id = '[email protected]' AND (enabled=1) Jan 9 22:43:38 mail authdaemond: password matches successfully Jan 9 22:43:38 mail authdaemond: authmysql: sysusername=<null>, sysuserid=5000, sysgroupid=5000, homedir=/var/spool/mail/virtual, [email protected], fullname=peter, maildir=<null>, quota=<null>, options=<null> Jan 9 22:43:38 mail authdaemond: authmysql: clearpasswd=<null>, passwd=6SrBcYq65l8QU Jan 9 22:43:38 mail authdaemond: Authenticated: sysusername=<null>, sysuserid=5000, sysgroupid=5000, homedir=/var/spool/mail/virtual, [email protected], fullname=peter, maildir=<null>, quota=<null>, options=<null> Jan 9 22:43:38 mail authdaemond: Authenticated: clearpasswd=peter, passwd=6SrBcYq65l8QU Jan 9 22:43:38 mail imapd: chdir Maildir: No such file or directory

  Read the article

• Proliant RAID 1 Rebuild Questions

  - by Nicholas

  I have a HP Proliant ML350 G5 server that experienced a power supply failure overnight. The power supply was replaced but unfortunately it got restarted with only 1 disk in the RAID 1 set plugged in. (The raid controller is the build in E200i). The raid BIOS then said on start-up that it had entered Interim Recovery Mode. However I would have expected it to still start up with only the 1 drive. The bios however says that it cannot find a C: drive and enters a reboot loop polling the other boot devices. First question is, is this normal behaviour not to start up on 1 disk? The second drive was then plugged in (all drives are ok) and the raid bios started an automatic rebuild on that disk. This appears to be a background process as there is no progress shown. However based on the light flashing it looks like it is working. My second question is how long will this rebuild take? (36GB 15K SAS drive). I cannot see any error messages and it looks like it is rebuilding the drive ok, but the computer still will not start-up. It still says during the boot up process that the C: drive is not found. If I wait for the rebuild to finish, is it likely to fix itself and find the C: drive? Or is there some other problem here?

  Read the article

• IMAP proxy as a POP3 hub?

  - by mailman stan

  Simple scenario, complicated technology: One family receiving mail from five email addresses via POP3 into one Outlook inbox on a single PC. Now we'd like to be able to replicate that single inbox across multiple devices (eg. desktop PC, laptop, netbook, smartphone). If we continue using POP3 as the mail transfer protocol, messages will be downloaded to one device and will not be visible to the others; replies will likewise be isolated on the sending machine. If we switch to IMAP, I understand that we can have multiple devices maintaining a shared view of an inbox hosted at the server end, but what about multiple accounts? I tried changing the account configuration in Outlook to fetch from the mail providers' IMAP service instead of POP3, which does give a shared view across multiple devices but also causes Outlook to create a separate inbox and PST for each account. This is awkward because it means there are five separate folders that need to be checked, and Outlook tools like search filters and rules don't seem to work across accounts. To get what I want (five accounts delivered into one shared mailbox) it seems that I would need some sort of intervening server that collects mail (using POP3) from all our accounts into a single inbox while preserving the original destination addresses, and then serves it up to all our devices using IMAP. Is this workable? Is it a good approach? Is there an easier way?

  Read the article

• Same domain only : smtp; 5.1.0 - Unknown address error 530-'SMTP authentication is required

  - by user124672

  I have a very strange problem after moving my netwave.be domain from WebHost4Life to Arvixe. I configured several email adresses, like [email protected] and [email protected]. For POP3 I can use mail.netwave.be, a mailserver hosted by Arvixe. However, for SMTP I have to use relay.skynet.be. Skynet (Belgacom) is one of the biggest internet providers in Belgium and blocks smtp requests to external mailservers. So for years I've been using relay.skynet.be to send my messages using [email protected] as the sender. The worked perfectly. After moving my domain to Arvixe, this is no longer the case. I can send emails to people, no problem. I have received emails too, so I suspect that's ok too. But I can't send emails from one user of my domain to another user. For example, if I send a mail from [email protected] to [email protected], relay.skynet.be picks up the mail just fine. A few seconds later, I get a 'Delivery Status Notification (Failure)' mail that contains: Reporting-MTA: dns; mailrelay012.isp.belgacom.be Final-Recipient: rfc822;[email protected] Action: failed Status: 5.0.0 (permanent failure) Remote-MTA: dns; [69.72.141.4] Diagnostic-Code: smtp; 5.1.0 - Unknown address error 530-'SMTP authentication is required.' (delivery attempts: 0) Like I said, this only seems to be the case when both the sender and recipient are adresses of a domain hosted by Arvixe. I have serveral accounts not related to Arvixe at all. I can use relay.skynet.be to send mail to [email protected] using these accounts. Likewise, I can use relay.skynet.be to send mail from [email protected] to these accounts. but not from one Arvixe account to another. I hope I have clearly outlined the problem and someone will be able to help me.

  Read the article

• Exim log and send all mail for a given domain through another server

  - by Josh

  I administer a handful of shared web hosting servers. Recently, Yahoo has been deprioritizing/greylising all email sent from these servers. I am getting the dereaded 421 4.7.0 [TS02] Messages from my.ip.address temporarily deferred message from Yahoo and their postmaster has been unresponsive. I am unable to find any way to set up a feedback loop like AOL has for my IP address -- I did find a way to set up a feedback loop for a given domain, but we host hundreds of domains, and don't have the time to set up that many feedback loops. So what I'd like to do is twofold: Configure Exim to send all email destined to an @yahoo.com address to a relay, a new server which has an IP that yahoo is not blocking. Configure Exim (or maybe the relay) to log all emails sent to @yahoo.com, so I can review them and, in case one of my uses is violating ToS and sending SPAM to yahoo users, take the appropriate action. How could I accomplish these? Or, does anyone have any other advice for how to get mail to flow through Yahoo and ensure that any email generating complaints is brought to my attention? (For what it's worth, these servers are not listed on any major blacklists)

  Read the article

• NFS: Server says "authenticated mount request", but client sees "access denied"

  - by zigdon

  I have two machine, an NFS server (RHEL) and a client (Debian). The server has NFS set up, exporting a particular directory: server:~$ sudo /usr/sbin/rpcinfo -p localhost program vers proto port 100000 2 tcp 111 portmapper 100000 2 udp 111 portmapper 100024 1 udp 910 status 100024 1 tcp 913 status 100021 1 udp 53391 nlockmgr 100021 3 udp 53391 nlockmgr 100021 4 udp 53391 nlockmgr 100021 1 tcp 32774 nlockmgr 100021 3 tcp 32774 nlockmgr 100021 4 tcp 32774 nlockmgr 100007 2 udp 830 ypbind 100007 1 udp 830 ypbind 100007 2 tcp 833 ypbind 100007 1 tcp 833 ypbind 100011 1 udp 999 rquotad 100011 2 udp 999 rquotad 100011 1 tcp 1002 rquotad 100011 2 tcp 1002 rquotad 100003 2 udp 2049 nfs 100003 3 udp 2049 nfs 100003 4 udp 2049 nfs 100003 2 tcp 2049 nfs 100003 3 tcp 2049 nfs 100003 4 tcp 2049 nfs 100005 1 udp 1013 mountd 100005 1 tcp 1016 mountd 100005 2 udp 1013 mountd 100005 2 tcp 1016 mountd 100005 3 udp 1013 mountd 100005 3 tcp 1016 mountd server$ cat /etc/exports /dir *.my.domain.com(ro) client$ grep dir /etc/fstab server.my.domain.com:/dir /dir nfs tcp,soft,bg,noauto,ro 0 0 All seems well, but when I try to mount, I see the following: client$ sudo mount /dir mount.nfs: access denied by server while mounting server.my.domain.com:/dir And on the server I see: server$ tail /var/log/messages Mar 15 13:46:23 server mountd[413]: authenticated mount request from client.my.domain.com:723 for /dir (/dir) What am I missing here? How should I be debugging this?

  Read the article

• error in php not logging or displaying

  - by Grant M

  I can not get any errors to display on screen on write to a log file. When check phpinfo() print out I have same value of master a local for display_errors On display_startup_errors On error_log /var/log/php.log error_reporting E_ALL & ~E_NOTICE log_errors On log_errors_max_len ls -l /var/log/php.log is -rw-rw-rw- 1 root root 0 Jun 21 07:47 /var/log/php.log for /var and /varlog drwxrwxrwx 23 root root 4096 Jun 2 11:13 var when there is an error in the code the page the browsers shows nothing and browser says there is no source for the page. Any suggestions of where else to look or change to errors to appear somewhere (anywhere would be good) edit: my error script is now <?php ini_set('display_errors', 1); error_reporting(E_ALL); echo "print from error.php 2 "; error //print from erroerror to cuase logging to happen. ?> this will print on display and to log Notice: Use of undefined constant error - assumed 'error' in /var/www/piku_dev2/error.php on line 7 but if I put garbage like #@$%$ on the error line I get nor error messages anywhere. Edit2: The problem turned out to in the httpd.conf file. I don't know what it was yet as it was fixed y someone else.

  Read the article

• Make Thundirbird use and sync with Gmail Spam facility

  - by Senthil

  I am using Thundirbird 3.1.7. I am using Gmail with it. When I mark a message as spam in Thunderbird, I want it to go to Gmail's spam folder. But it is not happening. The mail is only marked as spam and stays in Gmail's inbox. How can I setup Thunderbird so that when I mark a message as spam in thundirbird, it goes to spam folder in both Thunderbird and Gmail? FYI: I have disabled Thunderbird's own adaptive spam controls so that it doesn't interfere. I am perfectly fine with Gmail's spam facility and don't want Thunderbird to add another layer of spam filtering. Still Thunderbird doesn't send emails to Gmail's spam. Update I figured that dragging and dropping the email to the spam folder in Thunderbird does the job. But is it the same as marking the email as spam in Gmail's interface? i.e. Gmail will do stuff when you mark an email as spam so that it can filter out similar messages in the future. Does it happen when I do this drag and drop thing too? Are they the same?

  Read the article

• Throttling Postfix memory

  - by teddybeard

  I have a VPS on 1and1 similar to this configuration (512MB, burst up to 2GB). I run a web service where I crawl the web and notify my users through email and sms when a certain online data feed changes. When I send the emails out, I just have PHP loop through the recipients list and send the emails out using the mail() function. Whenever I try to send a large volume of these messages out, my server starts acting funny. I can't even run an 'ls' sometimes because the shell tells me it 'cannot allocate memory'. The shell is unusable and yet my website is being served up fine. Mail.err contains: Nov 14 17:30:09 s15351477 postfix/smtp[26000]: fatal: inet_addr_local[getifaddrs]: getifaddrs: Cannot allocate memory Nov 14 17:30:09 s15351477 postfix/sendmail[25999]: fatal: username(1000): unable to execute /usr/sbin/postdrop -r: Success Nov 14 18:29:14 s15351477 postfix/smtp[9911]: fatal: inet_addr_local[getifaddrs]: getifaddrs: Cannot allocate memory Nov 14 18:29:14 s15351477 postfix/sendmail[9910]: fatal: username(1000): unable to execute /usr/sbin/postdrop -r: Success Also, if relevant, my bean counters are: Version: 2.5 uid resource held maxheld barrier limit failcnt 53907331: kmemsize 20779422 21041560 31457280 34603008 2989403 lockedpages 0 0 512 512 0 privvmpages 81488 82498 524288 576716 94640 shmpages 2831 2831 32768 32768 0 dummy 0 0 9223372036854775807 9223372036854775807 0 numproc 90 91 128 128 6603 physpages 32692 33531 2147483647 2147483647 0 vmguarpages 0 0 131072 2147483647 0 oomguarpages 32942 33781 9223372036854775807 2147483647 0 numtcpsock 22 23 720 720 0 numflock 27 28 376 413 0 numpty 1 1 32 32 0 numsiginfo 0 1 512 512 0 tcpsndbuf 425888 441064 3440640 5406720 0 tcprcvbuf 369200 376832 3440640 5406720 0 othersockbuf 268000 268464 2252160 4194304 0 dgramrcvbuf 0 8472 524288 576716 0 numothersock 180 182 720 720 0 dcachesize 952146 966231 5242880 5767168 0 numfile 3609 3683 8192 8192 0 dummy 0 0 0 0 0 dummy 0 0 0 0 0 dummy 0 0 0 0 0 numiptent 25 25 200 205 0 Is there some way I can throttle postfix to keep it from swamping the system like this? Also wondering: why does email use so many resources, these emails are just short text?

  Read the article

• File upload permissions issue on Windows Server 2008 R2 IIS 7.5 PHP 5.3 with Drupal v.7.26

  - by Taras

  I have website on Drupal version: 7.26 OS on server is Windows Server 2008 R2 Web server $_SERVER["SERVER_SOFTWARE"]: Microsoft-IIS/7.5 Server API: CGI/FastCGI Core PHP Version: 5.3.28 file_uploads: On post_max_size: 75M upload_max_filesize: 50M upload_tmp_dir: C:\inetpub\wwwroot\tmp memory_limit: 128M open_basedir: C:\inetpub\wwwroot;C:\inetpub\wwwroot\tmp When I go to /admin/config/media/file-system I see error messages: The directory sites\default\files exists but is not writable and could not be made writable. The directory tmp exists but is not writable and could not be made writable. Public file system path: sites\default\files Temporary directory: tmp I have set permissions on folders C:\inetpub\wwwroot\tmp : IIS_IUSRS : Full control C:\inetpub\wwwroot\sites\default\files : IIS_IUSRS : Full control I am working as Administrator user: C:\Users\Administrator\Downloadsecho %username% Administrator I can`t change Read Only Attributes for these folders. Every time I do this change and press Apply button and Apply changes to this folder, subfolders and files is checked and press OK button it displays Applying attributes... dialog when it finishing I press OK button on folder properties dialog closing it. When I open Properties dialog once again I see Read-only is checked again. How can I fix it?

  Read the article

• How do I enable the confluence-users group?

  - by M. Joanis

  I've got an issue with Atlassian Confluence. Normal users can't log in, but administrators can... Details below! I manage users using an Apple Open Directory (LDAP). I created two groups: "confluence-administrators" and "confluence-users". I've added team leaders and managers to both groups, and I've added some users to "confluence-users". Everyone in "confluence-administrators" can log in easily. People in "confluence-users" can't log in at all. When I look at the user list (in Confluence), and select a user to examine the list of groups he or she belongs to, I can see that the Confluence Administrators are indeed members of the "confluence-administrators" group, but not a single user is a member of the "confluence-users" group. Not event the Confluence Administrators, which are members of both groups! So I tried to have one of the "confluence-users" log in while watching the Confluence logs. Here's the result: 2012-07-05 14:50:19,698 ERROR [http-8090-11] [core.event.listener.AutoGroupAdderListener] handleEvent Could not auto add user to group: Group <confluence-users> is read-only and cannot be updated at com.atlassian.crowd.directory.DbCachingRemoteDirectory.addUserToGroup(DbCachingRemoteDirectory.java:461) ... So it says the group group is read-only... I'm not sure why it is a problem. Well confluence-administrators too is read-only and it doesn't complain. Some things I don't think are part of the problem: I've synchronized Confluence with LDAP many, many times. I have verified many times that I didn't make a typo while setting the groups on the LDAP server. LDAP synchronization goes well. No errors in the logs (only INFO level log messages). The user exists. Errors in the logs are different when a user doesn't exist. Any help is most welcome!

  Read the article

• How can I make my PCI-E graphics card visible to Ubuntu when the motherboard has integrated graphics

  - by Norman Ramsey

  I have a Gigabyte GA-MA74GM-S2 motherboard with integrated graphics that shows up on lspci as an ATI Radeon 2100. I also bought a PCI-Express Nvidia graphics card so I could use the VDPAU feature on Linux (plays H.264 in hardware). The BIOS has three settings about which display to initialize first: Integrated graphics PCI graphics PCI-Express graphics (PEG) I set the BIOS on PEG, but I cannot get anything, not even a splash screen or POST messages, to emerge from the PCI-Express graphics card. (I'm using a DVI connector; the card also has an HDMI output.) I cannot get the kernel lspci to see the graphics card; the only VGA controller it acknowledges is the integrated one. Running dmidecode acknowledges the existence of an x16 PCI Express slot, and it says Current usage: Unknown There is an additional BIOS setting called "Internal Graphics Mode" which is normally set to "Auto" which means it is supposed to prefer a PCI Express VGA card. I set it to "Disabled" which now means I'm getting no output at all. I will soon be learning how to do a BIOS reset! Other information: The PCI-E card is a MSI N210-MD512H GeForce 210. This is a fanless card. Although there are no fans to see turning, the heat sink on the PCI-E card is definitely getting hot, so the card is getting some sort of power. It gets all its power from the PCI-E slot; there is no external power connector. The BIOS is an AMI Award BIOS. My question: how can I make the PCI Express graphics card visible to Ubuntu?

  Read the article

• frequent "SNMP error" with Cacti

  - by nn4l

  When adding new devices to my Cacti instance, I get frequent "SNMP error" messages in the device screen. But the error is not consistent, not even for the same device. Here's what I already have checked: Sometimes a device shows that "SNMP error" message even when it did not had that error an hour before, and vice versa. I tried this with several different Cacti releases, installed on different OS (Debian squeeze: 0.8.7g-1+squeeze1, Debian Sid: 0.8.7i-3, CentOS 6.0: 0.8.7i-2.el6) tried both from a local (192.168.1.xy) network and from a different data center so I don't think it is a network problem reinstalled the Cacti database, rerun the scripts to install my devices. Now different devices have that error when executing a snmpwalk or snmpgetnext command from the command line, it is always successful increasing the timeout to 20000 (20 seconds) and the retry count to 10 does not make a difference The cacti.log says: 04/14/2012 02:10:19 PM - CMDPHP: Poller[0] WARNING: SNMP GetNext Timeout for Host:'s0026.mydomain.de', and OID:'.1.3.6.1.2.1.1.3.0' 04/14/2012 02:10:20 PM - CMDPHP: Poller[0] WARNING: SNMP GetNext Timeout for Host:'s0026.mydomain.de', and OID:'.1.3' However, when executing snmpget or snmpget with that from the command line a proper response is returned immediately.

  Read the article

• Firebird 2.5 Database Corrupt

  - by BrendanH

  We have an issue where a database hangs the server when: a backup is performed (Hangs on a specific table) selecting * or count(1) from a specific table or viewing data that is related to the table (FKs, etc) We could browse the table to a certain point (using IBExpert) however after about 2900 records the machine just spikes and hangs. Performing a gfix -m does not work, and the validation reports back Record level errors = 4 (no matter how many times we run gfix -m, -v, etc. The Firebird.log file reports back these types of messages: Relation has 91631 orphan backversions (9214273 in use) in table BINS (137) - {Which is apparently just a warning} Unable to complete network request to host "MHPLZA1". Error reading data from the connection. INET/inet_error: read errno = 10054 SERVER/process_packet: broken port, server exiting Shutting down the server with 1 active connection(s) to 1 database(s), 0 active service(s) - {If we leave the backup to run while hanging, it eventually logs this error message} The setup is: The table is question has about 7000 records. The Firebird version is 2.5 Classic Server x64 install. The OS is Windows Server 2008. This is a virtual machine (VMWare) running on a massive server. (Does anyone have issues with VMs and Firebird?). We have the same setup running fine on other servers (However they are not virtual machines). Is there anyway to pin point the issue and or the cause?

  Read the article

• Perl TDS character sets

  - by skiphoppy

  I'm using the FreeTDS driver with DBD::Sybase, connecting to an MS SQL Server. When I query certain values of certain records, I get this error: DBD::Sybase::st fetchrow_arrayref failed: OpenClient message: LAYER = (0) ORIGIN = (0) SEVERITY = (9) NUMBER = (99) Server , database Message String: WARNING! Some character(s) could not be converted into client's character set. Unconverted bytes were changed to question marks ('?'). This seems to happen for records that contain special Windows character-set characters, such as curly quotes, copied and pasted from people's Outlook and Word messages. Unfortunately, I do not have any control of this database; sanitizing the input on the way in is obviously the way to go, but is not available to me. What FreeTDS settings do I need to change to be able to successfully query these records? Additional information: The query works fine from tsql. I only get this error through Perl's DBD::Sybase interface. (Should I test through something else? I don't have the expertise yet to install PHP or Python. I've got jTDS and can use it, but I think that's a completely different implementation, not an interface to FreeTDS.) Adding client charset = UTF-8 to my freetds.conf file results in "Out of memory!" printed to STDERR.

  Read the article

• get-eventlog issue

  - by Jim B

  I wanted to get a quick report of some log entries I saw on a server, so I ran: Get-Eventlog -logname system -newest 10 -computer fs1 | fl I got events back however the descriptions were all wrong. Here's an example: Index : 1260055 EntryType : Warning InstanceId : 2186936367 Message : The description for Event ID '-2108030929' in Source 'W32Time' cannot be found. The local compute r may not have the necessary registry information or message DLL files to display the message, or you may not have permission to access them. The following information is part of the event:'time. windows.com,0x1' Category : (0) CategoryNumber : 0 ReplacementStrings : {time.windows.com,0x1} Source : W32Time TimeGenerated : 1/25/2010 10:43:31 AM TimeWritten : 1/25/2010 10:43:31 AM UserName : Note that if I pull the event ID property it's correct (in this case 38) Is this is known issue or is something wrong. The messages resolve fine via event viewer locally and remotely Here is the powershell version info: Name : ConsoleHost Version : 2.0 InstanceId : bc58fcf8-bba3-4ca8-8972-17dbd5d9ff08 UI : System.Management.Automation.Internal.Host.InternalHostUserInterface CurrentCulture : en-US CurrentUICulture : en-US PrivateData : Microsoft.PowerShell.ConsoleHost+ConsoleColorProxy IsRunspacePushed : False Runspace : System.Management.Automation.Runspaces.LocalRunspace Here is the revised version info: Name Value ---- ----- CLRVersion 2.0.50727.3603 BuildVersion 6.0.6002.18111 PSVersion 2.0 WSManStackVersion 2.0 PSCompatibleVersions {1.0, 2.0} SerializationVersion 1.1.0.1 PSRemotingProtocolVersion 2.1

  Read the article

• exim4 - disable autoreplies about "SMTP error from remote mail server after RCPT"

  - by osgx

  Hello I have a setup of exim4 on domain1 in front of other server, domain2 (with sendmail). Second server have no direct access to internet, so domain1 is MX for domain2. And domain2 is set as hubbed_host in the exim4 on domain1. When spammer sends message for no_such_user@domain2, its sendmail do a reject: 550 5.1.1 <no_such_user@domain2>... User unknown Then, exim4 at domain1 do an auto-reply like this: This message was created automatically by mail delivery software. A message that you sent could not be delivered to one or more of its recipients. This is a permanent error. The following address(es) failed: no_such_user@domain2 SMTP error from remote mail server after RCPT TO:<no_such_user@domain2>: host 10.0.0.1 [10.0.0.1]: 550 5.1.1 <no_such_user@domain2>... User unknown The spammers uses fake "from" field, and such generated messages are frozen by exim for a long time. How can I disable some or all autoreplies from exim4? Ideally, I want a filter, if message was not delivered with error "User unknown" than don't generate any autoreply from mailer-daemon. Thanks!

  Read the article

• Debian Squeeze and exim4: cannot send mail

  - by Fernando Campos

  Hello guys, Got this error after install and config of exim4-daemon-light and mailutils packages on Debian Squeeze. This package is aimed to send automatic messages from websites, like email confirmation and stuff. Configuration after package install: dpkg-reconfigure exim4-config You'll be presented with a welcome screen, followed by a screen asking what type mail delivery you'd like to support. Choose the option for "internet site" and select "Ok" to continue. After many configuration sceens you can test mail with: echo "test message" | mail -s "test message" [email protected] Here is the response: root@server:/etc# echo "test message" | mail -s "test message" [email protected] 2011-03-02 20:34:59 1PuxRT-0001Aj-T9 Cannot open main log file "/var/log/exim4/mainlog": Permission denied: euid=101 egid=103 2011-03-02 20:34:59 1PuxRT-0001Aj-T9 <= root@debian U=root P=local S=331 2011-03-02 20:34:59 1PuxRT-0001Aj-T9 Cannot open main log file "/var/log/exim4/mainlog": Permission denied: euid=101 egid=103 exim: could not open panic log - aborting: see message(s) above Can't send mail: sendmail process failed with error code 1 There is no /var/log/exim4 directory on my server. I tried to create it, but it didn't work. Please, can someone help me? Best regards, Fernando

  Read the article

• How to inspect remote SMTP server's TLS certificate?

  - by Miles Erickson

  We have an Exchange 2007 server running on Windows Server 2008. Our client uses another vendor's mail server. Their security policies require us to use enforced TLS. This was working fine until recently. Now, when Exchange tries to deliver mail to the client's server, it logs the following: A secure connection to domain-secured domain 'ourclient.com' on connector 'Default external mail' could not be established because the validation of the Transport Layer Security (TLS) certificate for ourclient.com failed with status 'UntrustedRoot. Contact the administrator of ourclient.com to resolve the problem, or remove the domain from the domain-secured list. Removing ourclient.com from the TLSSendDomainSecureList causes messages to be delivered successfully using opportunistic TLS, but this is a temporary workaround at best. The client is an extremely large, security-sensitive international corporation. Our IT contact there claims to be unaware of any changes to their TLS certificate. I have asked him repeatedly to please identify the authority that generated the certificate so that I can troubleshoot the validation error, but so far he has been unable to provide an answer. For all I know, our client could have replaced their valid TLS certificate with one from an in-house certificate authority. Does anyone know a way to manually inspect a remote SMTP server's TLS certificate, as one can do for a remote HTTPS server's certificate in a web browser? It could be very helpful to determine who issued the certificate and compare that information against the list of trusted root certificates on our Exchange server.

  Read the article

< Previous Page | 208 209 210 211 212 213 214 215 216 217 218 219  | Next Page >