Search Results

Search found 6164 results on 247 pages for 'sd card'.

Page 217/247 | < Previous Page | 213 214 215 216 217 218 219 220 221 222 223 224  | Next Page >

• Cisco 7206 error trying to copy running-config (Bad file number)

  - by jasondewitt

  I have a cisco 7206 that terminates a bunch of pppoa sessions for dsl users. Today I noticed that if I tried to "show run" nothing happened. I mean that it doesn't show anything and just sends me right back to the command prompt. I decided I should probably try and back up the config and that is where I'm stuck. Any time I try to copy the running-config to tftp or to pcmcia card that I know is not full I get the following error: %Error opening system:/running-config (Bad file number) I get this error when I try to do anything with the running config. I've been googling around, but I haven't found any thing else that talks about this error. I've seen people say to erase the nvram and then try to "copy run start", but I don't want to erase the nvram until I can pull off a copy of the running-config. I would try to reboot it, but the startup-config that is on the nvram looks to be woefully out of date (good job me!). Any ideas what might be wrong? or how I can get the running config off the router?

  Read the article

• NFS high CPU usage

  - by user269836

  Hello, I have a very strange issue. I have next server: Intel(R) Xeon(TM) MP CPU 3.16GHz cat /proc/cpuinfo | grep proce | wc -l 8 free -m total used free shared buffers cached Mem: 28203 27606 596 0 10789 9714 -/+ buffers/cache: 7103 21100 Swap: 24695 0 24695 RAID card *-storage description: RAID bus controller product: MegaRAID vendor: LSI Logic / Symbios Logic physical id: 7 bus info: pci@0000:13:07.0 logical name: scsi2 version: 01 width: 32 bits clock: 66MHz capabilities: storage pm bus_master cap_list rom configuration: driver=megaraid latency=32 resources: irq:134 memory:d8ff0000-d8ffffff(prefetchable) memory:df600000-df60ffff(prefetchable) HDD: 10x148Gb SCSI U320 15k - RAID5 /dev/sdb1 807G 674G 93G 88% /storage /dev/sdb1 /storage ext4 defaults,usrjquota=aquota.user,grpjquota=aquota.group,jqfmt=vfsv0,noatime,nodiratime,noacl,errors=remount-ro 0 1 network cards ethtool -i eth0 driver: tg3 version: 3.116 firmware-version: 5704-v3.36, ASFIPMIc v2.36 bus-info: 0000:10:02.0 ethtool -i eth1 driver: tg3 version: 3.116 firmware-version: 5704-v3.36, ASFIPMIc v2.36 bus-info: 0000:10:02.0 ifconfig bond0 Link encap:Ethernet HWaddr 00:0f:1f:ff:d6:4d inet addr:192.168.15.71 Bcast:192.168.15.255 Mask:255.255.255.0 inet6 addr: fe80::20f:1fff:feff:d64d/64 Scope:Link UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1 RX packets:1062818202 errors:0 dropped:3918 overruns:0 frame:0 TX packets:1041317321 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:10000 RX bytes:258867684559 (241.0 GiB) TX bytes:396569192650 (369.3 GiB) this server running only nfs-kernel-server uname -a Linux nas2-backup 2.6.32-5-amd64 #1 SMP Sun Sep 23 10:07:46 UTC 2012 x86_64 GNU/Linux Debian 6. What do I have, once per day or two, LA goes up, it can be reached around LA: 40 but if I do: nfs-kernel-server restart. Every thing is OK. But on the next day or a little bit later, LA goes up again. Servers are connected to d-link dgs 1016d with 24 GBits ports. I have tried everything to find out what the problem is. Why it's happening, but still I can not resolve this issue. Any ideas on what is happening here?

  Read the article

• Ubuntu 11.10 ATI Drivers vesa park

  - by Matthias

  This is probably not an issue, from all I can get it seems my hardware and drivers are properly installed. However when I go to system settings - system info - graphics. I get Driver: VESA:PARK. Experience: Standard. my graphics card is a: Ati Mobility Radeon HD 5470 512MB. I am pretty sure it's not a same-die GPU since there is a fan exhaust at the side of my laptop which I presume is the exhaust for the GPU... I have no clue whatsoever what this means. I installed the ati drivers first using the 'additional drivers' method. However I also decided to look a manual installation up via the terminal since I've had problems before with Ubuntu and ati cards. I used wget and something among the lines of sh dpkg -i. I can recall exactly, I took them from another stackoverflow answer. Anyway, it seems everything is installed properly since it shows up with these commands: sudo lshw -C video fglrxinfo however the first command seems to detect hardware, not the driver per se, although the driver is probably needed to detect the hardware anyway which would indicate its properly installed. I am still not sure about that VES:PARK thing though. I'd like to know what it means.. Also, if someone happens to know a good way of testing if the gpu is connected/being used...some sort of benchmark maybe...I'd like to hear it. P.s. I can find my way around in Ubuntu but I would probably still be considered a rookie by more experienced users.

  Read the article

• Rebuild Apple RAID set

  - by Clinton Blackmore

  We have a Mac Pro tower with an Apple RAID card in it using third party drives. When one drive failed, we replaced it and the RAID 5 set was nearly done rebuilding when the computer was rebooted. It did not come back up. We are now booting up off of a different internal volume, and have three (third-party) drives of identical spec (including revision and firmware) in the box. One of the drives is a global spare; the other two are recognized as belong to a RAID set but are in "Roaming" mode. The intention is to recreate the three-drive RAID set using the data on the two drives that are good. When we tell the system to create a RAID 5 using the three drives, it tells us that it'll create a RAID set but everything will be lost. There are no obvious options to rebuild a RAID using the two good drives and incorporating the third drive in Apple's RAID Utility, and we've looked through the options for the raidutil command. Fortunately, all important data is backed up, and we can rebuild from scratch, but, is there any way to make the RAIDset work again?

  Read the article

• How to get gigabit network speeds on Windows XP?

  - by JB

  We've just installed gigabit switches at work, and things on the Linux side are going well. Our linux boxes, which use a Intel Corporation 82566DM-2 Gigabit nic (according to lspci), consistently get over 900 mbits/sec: iperf -c ipserver ------------------------------------------------------------ Client connecting to ipserver, TCP port 5001 TCP window size: 16.0 KByte (default) ------------------------------------------------------------ [ 3] local 192.168.40.9 port 39823 connected with 192.168.1.115 port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.0 sec 1.08 GBytes 929 Mbits/sec We have a bunch of Windows XP 64-bit machines that use Broadcom NetXtreme 57xx cards. I spent around a day trying to get equivalent speeds on them, but couldn't get above 200 Mbits/sec. I noticed the Windows iperf tests said that the TCP window size was 8 Kb by default (as opposed to 16 Kb on Linux, so I modified my test to reflect that. Still no love. I went to Broadcom's site, downloaded the latest drivers for the card and installed. Still no love. However, finally, I tried a 64 Kb window size with the new drivers, and finally an improvement! $ iperf -c ipserver -w64k ------------------------------------------------------------ Client connecting to ipserver, TCP port 5001 TCP window size: 64.0 KByte ------------------------------------------------------------ [ 3] local 192.168.40.214 port 1848 connected with 192.168.1.115 port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.0 sec 933 MBytes 782 Mbits/sec Much better, but still not really taking advantage of the full capabilities of the network. If the Linux box can reach 950 Mbits/sec consistently, this box should be able to as well. Also, if you're wondering about the medium, this is over the same cable...I'm switching back and forth. Any suggestion or ideas would be really welcome. Thanks!

  Read the article

• Can one really fry a monitor by setting the wrong HorizSync and VertRefresh?

  - by rumtscho

  I've encountered this problem on several different systems with several different monitors: a monitor functions perfectly under Windows. I install a Linux and the max resolution is at some impossibly low value, mostly 640x480, changing it in Xorg.conf doesn't work. The X.org log file then shows that the driver cannot determine the correct refresh rate for the monitor, so it ignores everything in Xorg.conf and just loads in some default minimalistic mode. Googling the problem leads to an easy solution: set the HorizSync and VertRefresh in Xorg.conf, and everything works. The problem seems to be a common one, and I've seen dozens of results recommending the solution. Each of them contains the warning that you should use the value ranges provided with the monitor. Because if you don't, and your video card sends a signal with the wrong refresh rate, this can damage your monitor. Of course, you don't have a user manual for your monitor any more. If you are lucky to find one on the attic or on the net, it doesn't contain any information about the supported refresh rate. So you just type in the value suggested in the solution description, which varies wildly depending on your source, and cross your fingers. You restart, and... ... you've set the wrong values. So the monitor shows a short message like "input signal out of range", and you do a hard restart, repair your Xorg.conf in recovery mode, and everything is fine, including your monitor. So does this warning reflect a real possibility, or is it just a geeky urban legend? Or is it something which used to happen in the past, before manufacturers started protecting the monitors against it? Is it technically possible with every monitor technology, or is it maybe something which can only happen to a CRT? If you think that it's true, why? Have you ever witnessed a monitor die from the wrong refresh config, or have you read of it in a reputable source?

  Read the article

• No signal on monitor after plug it to a linux box

  - by yaroot

  I use my old computer as an NAS, so I remove the monitor after I installed linux on it (disconnect vga cable). I use ssh to control the machine and it works fine. Until some day, after kernel/softare upgrade or messing up some configs, I cannot connect to it through ssh, then I have to plug the monitor back, but the monitor says "No input signal". So I have to restart the computer WITH the monitor connected, and the monitor's back! I think the computer/linux kernel doesn't detect the monitor plug-in event. So how can I start my linux box without a monitor, but when it goes wrong I can still plug my monitor (vga) back and use the console. Edit: just one pci-e video card, has dvi, vga, tv/out (s-video) Edit2: Xorg is not running. I just need the console (CTRL+ALT+F1). The problem is, if the machine booted without a monitor connected, it won't give me a pseudo terminal after I attach the vga cable while it's running. Clearly the monitor is not auto detected as usb device. I'm wondering how to let the monitor auto detected.

  Read the article

• Internet Connection not working - USB LAN connection - from particular modem

  - by Paul

  I am trying to fix Internet connection on a friends Dell inspiron 1720 with XP service pack 3. It has an integrated network card that stopped working, after powering down/up the modem still didnt work I brought it back to my place to try a few things ie check cable, update driver etc... still didnt work. So I bought a USB LAN connector. It didnt work straight away but I went to configure the properties and changed the ConnectionType from AutoSense to 100 BaseT 10BaseT Full_Duplex, I basically just tried them all. From my place when connected to my desktop - 10 BaseT and 10BaseT Full_Duplex worked. From my place When connected to their laptop - 10 BaseT and 10BaseT Full_Duplex worked. Happy I went back to my friends house confident it would all work, and it didnt. Brought it back to mine and it did. While there, in Network Connections the connection is there recognized, enabled, 'working properly' it just says not connected. Also there is no led on the USB connector While at mine as above except there is an led on the USB connector and it says connected. Other difference I can think of is they have a cable modem, I'm plugged into the back of a Belkin wireless router - would this make a difference? Any other ideas what to try? (Would getting the model of the cable modem help anyone?) The USB connector is "DM9601 USB to Fast Ethernet"

  Read the article

• I can't connect to my network, except in safe mode

  - by eidylon

  My laptop cannot connect to my network all of a sudden except in safe mode. When it boots, it will show the networks available in the tray popup, but if I click connect on any, it says "Unable to connect" and the troubleshooter is useless. Shortly thereafter all the networks disappear. I have tried removing IPv6 support as I have seen that cause problems. No joy. I've also tried removing the wireless network adapter in Device Manager and reinstalling it, also no joy. I've also tried attaching a USB wireless adapter, and it has the same problem. If I boot in safe mode, then it has no problems at all. Three other devices in the house connect fine, so I am pretty sure it is nothing to do with the router. Any ideas what to check next? I am running Win7 Ultimate on a 2GHz Quadcore with 8GB RAM with a Broadcom 802.11n wireless card. EDIT: RE wired connections: What is very weird is that if i plug in a wired connection, then not only does it connect via the wired connection, but the wireLESS also starts working perfectly. And a soon as I unplug the wire, then the wireLESS stops working again! So it seems the wireless is right now working only in safe-mode, or when a wired connection is also plugged in.

  Read the article

• The bottlenecks of any computer, what to look for?

  - by WebDevHobo

  Whether it is a laptop or a desktop, any computer is made up of several pieces of hardware that communicate with each other. Sending data back and forth to ensure that the user gets the desired results. I have seen some theoretical stuff on computers & hardware, but I wonder how it all comes together. CPU RAM Graphics Card L1 CACHE L2 CACHE L3 CACHE FSB ... And all other things. Which is the biggest bottle neck? Why would a person not want/need a big value in one of those categories in certain situations? P.S.: when reading the specs of the i5 750 processor, I came across this description: In place of the FSB, one or more high speed, point-to-point buses called Quick Path Interconnect (QPI) are used, formerly known as Common Serial Interconnect Bus or CSI. QPI features higher bandwidth than the traditional FSB and is better suited to system scaling. What is this, and how does it compare to FSB? EDIT: I am not planning to buy a computer at all. The goal of this question is to understand the internal relation of various hardware pieces, their specific functions and how they work together. For instance, I have heard to a somewhat higher-than-usual amount of L2/L3 Cache can help speed up your computer. What's up with saying that? Also I forgot to mention Hard-disk RPM.

  Read the article

• Dell PERC 5 - RAID-10 keeps rebuilding drive 2 every day

  - by raid question

  I have a Dell PowerEdge 2950 with this card: RAID bus controller [0104]: Dell PowerEdge Expandable RAID controller 5 [1028:0015] and six disks in a RAID-10. I replaced drive 2, because it didn't show up, and then it started to rebuild itself: root@backup01:~# megaraidsas-status -- Arrays informations -- -- ID | Type | Size | Status a0d0 | RAID 10 | 5587GiB | DEGRADED -- Disks informations -- ID | Model | Status | Warnings a0e8s0 | ATA ST2000DM001-9YN1 1863GiB | online | errs: media:0 other:5393 a0e8s1 | ATA ST2000DM001-9YN1 1863GiB | online | errs: media:0 other:5394 a0e8s2 | ATA ST2000DM001-1E61 1863GiB | rebuild | errs: media:0 other:99 a0e8s3 | ATA ST2000DM001-9YN1 1863GiB | online | errs: media:0 other:5393 a0e8s4 | ATA ST2000DM001-9YN1 1863GiB | online | errs: media:0 other:5393 a0e8s5 | ATA ST2000DM001-9YN1 1863GiB | online | errs: media:0 other:5393 The rebuild finishes, then the virtual drive becomes optimal, and drive 2 goes online. Then once a day, drive 2 acts like it's been removed, and the rebuild starts all over again. How do I make this once a day rebuild stop? Event Description: Removed: PD 02(e1/s2) Event Description: Removed: PD 02(e1/s2) Info: enclPd=08, scsiType=0, portMap=04, sasAddr=1221000002000000,0000000000000000 Event Description: State change on VD 00/0 from OPTIMAL(3) to DEGRADED(2) Event Description: VD 00/0 is now DEGRADED1 Event Description: State change on PD 02(e1/s2) from ONLINE(18) to FAILED(11) Event Description: State change on PD 02(e1/s2) from FAILED(11) to UNCONFIGURED_BAD(1) Event Description: Background Initialization failed on VD 00/0 Event Description: Inserted: PD 02(e1/s2) Event Description: Inserted: PD 02(e1/s2) Info: enclPd=08, scsiType=0, portMap=04, sasAddr=1221000002000000,0000000000000000 Event Description: PD 02(e1/s2) is not a certified drive Event Description: State change on PD 02(e1/s2) Event Description: State change on PD 02(e1/s2) from UNCONFIGURED_GOOD(0) to OFFLINE(10) from UNCONFIGURED_BAD(1) to UNCONFIGURED_GOOD(0) Event Description: Rebuild automatically started on PD 02(e1/s2) Event Description: State change on PD 02(e1/s2) from OFFLINE(10) to REBUILD(14)

  Read the article

• Degraded RAID5 and no md superblock on one of remaining drive

  - by ark1214

  This is actually on a QNAP TS-509 NAS. The RAID is basically a Linux RAID. The NAS was configured with RAID 5 with 5 drives (/md0 with /dev/sd[abcde]3). At some point, /dev/sde failed and drive was replaced. While rebuilding (and not completed), the NAS rebooted itself and /dev/sdc dropped out of the array. Now the array can't start because essentially 2 drives have dropped out. I disconnected /dev/sde and hoped that /md0 can resume in degraded mode, but no luck.. Further investigation shows that /dev/sdc3 has no md superblock. The data should be good since the array was unable to assemble after /dev/sdc dropped off. All the searches I done showed how to reassemble the array assuming 1 bad drive. But I think I just need to restore the superblock on /dev/sdc3 and that should bring the array up to a degraded mode which will allow me to backup data and then proceed with rebuilding with adding /dev/sde. Any help would be greatly appreciated. mdstat does not show /dev/md0 # cat /proc/mdstat Personalities : [linear] [raid0] [raid1] [raid10] [raid6] [raid5] [raid4] [multipath] md5 : active raid1 sdd2[2](S) sdc2[3](S) sdb2[1] sda2[0] 530048 blocks [2/2] [UU] md13 : active raid1 sdd4[3] sdc4[2] sdb4[1] sda4[0] 458880 blocks [5/4] [UUUU_] bitmap: 40/57 pages [160KB], 4KB chunk md9 : active raid1 sdd1[3] sdc1[2] sdb1[1] sda1[0] 530048 blocks [5/4] [UUUU_] bitmap: 33/65 pages [132KB], 4KB chunk mdadm show /dev/md0 is still there # mdadm --examine --scan ARRAY /dev/md9 level=raid1 num-devices=5 UUID=271bf0f7:faf1f2c2:967631a4:3c0fa888 ARRAY /dev/md5 level=raid1 num-devices=2 UUID=0d75de26:0759d153:5524b8ea:86a3ee0d spares=2 ARRAY /dev/md0 level=raid5 num-devices=5 UUID=ce3e369b:4ff9ddd2:3639798a:e3889841 ARRAY /dev/md13 level=raid1 num-devices=5 UUID=7384c159:ea48a152:a1cdc8f2:c8d79a9c With /dev/sde removed, here is the mdadm examine output showing sdc3 has no md superblock # mdadm --examine /dev/sda3 /dev/sda3: Magic : a92b4efc Version : 00.90.00 UUID : ce3e369b:4ff9ddd2:3639798a:e3889841 Creation Time : Sat Dec 8 15:01:19 2012 Raid Level : raid5 Used Dev Size : 1463569600 (1395.77 GiB 1498.70 GB) Array Size : 5854278400 (5583.08 GiB 5994.78 GB) Raid Devices : 5 Total Devices : 4 Preferred Minor : 0 Update Time : Sat Dec 8 15:06:17 2012 State : active Active Devices : 4 Working Devices : 4 Failed Devices : 1 Spare Devices : 0 Checksum : d9e9ff0e - correct Events : 0.394 Layout : left-symmetric Chunk Size : 64K Number Major Minor RaidDevice State this 0 8 3 0 active sync /dev/sda3 0 0 8 3 0 active sync /dev/sda3 1 1 8 19 1 active sync /dev/sdb3 2 2 8 35 2 active sync /dev/sdc3 3 3 8 51 3 active sync /dev/sdd3 4 4 0 0 4 faulty removed [~] # mdadm --examine /dev/sdb3 /dev/sdb3: Magic : a92b4efc Version : 00.90.00 UUID : ce3e369b:4ff9ddd2:3639798a:e3889841 Creation Time : Sat Dec 8 15:01:19 2012 Raid Level : raid5 Used Dev Size : 1463569600 (1395.77 GiB 1498.70 GB) Array Size : 5854278400 (5583.08 GiB 5994.78 GB) Raid Devices : 5 Total Devices : 4 Preferred Minor : 0 Update Time : Sat Dec 8 15:06:17 2012 State : active Active Devices : 4 Working Devices : 4 Failed Devices : 1 Spare Devices : 0 Checksum : d9e9ff20 - correct Events : 0.394 Layout : left-symmetric Chunk Size : 64K Number Major Minor RaidDevice State this 1 8 19 1 active sync /dev/sdb3 0 0 8 3 0 active sync /dev/sda3 1 1 8 19 1 active sync /dev/sdb3 2 2 8 35 2 active sync /dev/sdc3 3 3 8 51 3 active sync /dev/sdd3 4 4 0 0 4 faulty removed [~] # mdadm --examine /dev/sdc3 mdadm: No md superblock detected on /dev/sdc3. [~] # mdadm --examine /dev/sdd3 /dev/sdd3: Magic : a92b4efc Version : 00.90.00 UUID : ce3e369b:4ff9ddd2:3639798a:e3889841 Creation Time : Sat Dec 8 15:01:19 2012 Raid Level : raid5 Used Dev Size : 1463569600 (1395.77 GiB 1498.70 GB) Array Size : 5854278400 (5583.08 GiB 5994.78 GB) Raid Devices : 5 Total Devices : 4 Preferred Minor : 0 Update Time : Sat Dec 8 15:06:17 2012 State : active Active Devices : 4 Working Devices : 4 Failed Devices : 1 Spare Devices : 0 Checksum : d9e9ff44 - correct Events : 0.394 Layout : left-symmetric Chunk Size : 64K Number Major Minor RaidDevice State this 3 8 51 3 active sync /dev/sdd3 0 0 8 3 0 active sync /dev/sda3 1 1 8 19 1 active sync /dev/sdb3 2 2 8 35 2 active sync /dev/sdc3 3 3 8 51 3 active sync /dev/sdd3 4 4 0 0 4 faulty removed fdisk output shows /dev/sdc3 partition is still there. [~] # fdisk -l Disk /dev/sdx: 128 MB, 128057344 bytes 8 heads, 32 sectors/track, 977 cylinders Units = cylinders of 256 * 512 = 131072 bytes Device Boot Start End Blocks Id System /dev/sdx1 1 8 1008 83 Linux /dev/sdx2 9 440 55296 83 Linux /dev/sdx3 441 872 55296 83 Linux /dev/sdx4 873 977 13440 5 Extended /dev/sdx5 873 913 5232 83 Linux /dev/sdx6 914 977 8176 83 Linux Disk /dev/sda: 1500.3 GB, 1500301910016 bytes 255 heads, 63 sectors/track, 182401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sda1 * 1 66 530113+ 83 Linux /dev/sda2 67 132 530145 82 Linux swap / Solaris /dev/sda3 133 182338 1463569695 83 Linux /dev/sda4 182339 182400 498015 83 Linux Disk /dev/sda4: 469 MB, 469893120 bytes 2 heads, 4 sectors/track, 114720 cylinders Units = cylinders of 8 * 512 = 4096 bytes Disk /dev/sda4 doesn't contain a valid partition table Disk /dev/sdb: 1500.3 GB, 1500301910016 bytes 255 heads, 63 sectors/track, 182401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sdb1 * 1 66 530113+ 83 Linux /dev/sdb2 67 132 530145 82 Linux swap / Solaris /dev/sdb3 133 182338 1463569695 83 Linux /dev/sdb4 182339 182400 498015 83 Linux Disk /dev/sdc: 1500.3 GB, 1500301910016 bytes 255 heads, 63 sectors/track, 182401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sdc1 1 66 530125 83 Linux /dev/sdc2 67 132 530142 83 Linux /dev/sdc3 133 182338 1463569693 83 Linux /dev/sdc4 182339 182400 498012 83 Linux Disk /dev/sdd: 2000.3 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sdd1 1 66 530125 83 Linux /dev/sdd2 67 132 530142 83 Linux /dev/sdd3 133 243138 1951945693 83 Linux /dev/sdd4 243139 243200 498012 83 Linux Disk /dev/md9: 542 MB, 542769152 bytes 2 heads, 4 sectors/track, 132512 cylinders Units = cylinders of 8 * 512 = 4096 bytes Disk /dev/md9 doesn't contain a valid partition table Disk /dev/md5: 542 MB, 542769152 bytes 2 heads, 4 sectors/track, 132512 cylinders Units = cylinders of 8 * 512 = 4096 bytes Disk /dev/md5 doesn't contain a valid partition table

  Read the article

• Public static ip for vagrant box

  - by Numbata

  I have server (Debian Squeeze) with 1 ethernet card and 2 public static IPs (188.120.245.4 and 188.120.244.5). What I want: Setup virtual box (Ubuntu) with access via static IP (188.120.244.5). What I was trying: config.vm.forward_port - good idea: setup interface "eth1:1" with 188.120.244.5 on host-machine, and add to Vagrant file "config.vm.forward_port = hmm..?" config.vm.network :hostonly, "188.120.244.5" - not working. Was created new interface on host-machine with ip "188.120.244.1". Of course 188.120.244.1 IP isn't mine and I can't access my server via this IP. config.vm.network :bridged - I'm confused how this works :) What I have now: Not working configuration. Debian-host-machine# cat Vagrantfile Vagrant::Config.run do |config| config.vm.define :gitlab do |box_config| box_config.vm.box = "ubuntu" box_config.vm.host_name = "ubuntu" box_config.vm.network :bridged box_config.vm.network :hostonly, "188.120.244.5", :auto_config => false end end Debian-host-machine# ifconfig eth1 Link encap:Ethernet HWaddr 00:15:17:69:71:bb inet addr:188.120.245.4 Bcast:188.120.247.255 Mask:255.255.248.0 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 vboxnet0 Link encap:Ethernet HWaddr 0a:00:27:00:00:00 inet addr:188.120.244.1 Bcast:188.120.246.255 Mask:255.255.255.0 Ubuntu-virtual-machine# ifconfig eth0 Link encap:Ethernet HWaddr 08:00:27:ee:8d:0c inet addr:10.0.2.15 Bcast:10.0.2.255 Mask:255.255.255.0 eth1 Link encap:Ethernet HWaddr 08:00:27:45:71:87 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 How I can access virtual box via public static IP from network? I'm using Oracle VM VirtualBox Manager 4.1.18 and Vagrant version 1.0.3. Thanks in advance for your feedback.

  Read the article

• Trying to understand Wireless N vs Wireless AC

  - by EGHDK

  Whenever a new wireless standard gets approved you expect faster speeds and longer range. From everything that I've read about it, it seems that AC will only transfer over the 5GHz band and up to 3Gbps. Studying the new AC routers on the market, it seems that they will transfer over 5GHz and 2.4GHz. And 5GHz will only transfer at 1.3Gbps. Which isn't what AC is supposed to be. I know there is a difference between what the standard actually says, and what products will actually do, but is there any reason for this? Is there any other main differences between AC and N? I've heard people discussing AC and saying that it's finally "fixing" what N was supposed to fix... what do they mean by that? Any security benefits? I have seen this image online: Will AC really do that? Will that require an AC network card in my laptop for that to actually happen? Lastly, will the router only be able to communicate with AC devices if I have beamforming technology on? I know it's a ton of questions, but most articles online seem to be outdated, and don't provide too much reliability.

  Read the article

• Media Center setup won't complete for watching TV

  - by Robert

  I have a problem watching TV in Media Center. The TV constantly pauses 1/2 second then plays 1 second, pauses 1/2 second, plays 1 second - it is constant and does not vary. This problem occurs on all channels, live or recorded. The bottom 5th of the screen is solid green. I know the problem is Media Center because I can use Pinnacle's TVCenterPro and there is no skipping/pausing (and not green on bottom). I was using cable, and switched to DirecTV (satellite). Trying to do "Set up TV signal" in Media Center seems to be what broke it. I get an error "IR Hardware not detected." I can use the remote to "try again" - so the IR hardware works fine (Media Center's remote/sensor). I tried plugging the IR Blaster into both ports, and I tried a different USB port for the IR receiver. I can't complete the setup. Media Center was playing it okay before I tried to run setup. (I ran setup to try to do recording with Media Center.) Pinnacle PCTV 800i HD PCI card (coax cable from DirecTV tuner), ATI Radeon HD 3200 Graphics, Windows XP SP3 Media Center Edition, AMD Athlon Dual Core 2.5 GHz, 1.75 GB RAM.

  Read the article

• Macs don't connect to wifi access point but PCs will

  - by Josh

  So, as a side project I'm going to try and figure out why the wifi APs in my building exhibit the following behavior: - They typically allow all types of computers to connect without issues - Sometimes Apples can't get an IP address but will still connect to the AP's signal - Less often, PCs can't connect to the wifi (same as above - yes signal, no IP addy) - Don't let Raiders fans on no matter the time of day! My first thought was that the DHCP leases were all taken up when the Apples would try to connect, and it was just their unlucky timing, but I would then try to log on with a PC that had a new, unleased MAC address and it would work... Could this be something to do with interoperability between an apple wifi card, and the APs? Different parts of the DHCP lease being taken up first? The fact that the Seattle Mariners might actually be good this year?? If this hasn't used up everyone's patience (with my crappy sports jokes), something else I could use some help with: - We don't have the model or type of AP - This is because there is no documentation available for them, and they literally look like small white boxes with no writing on them. Also, the company that installed them is out of business, so the situation might be that no docs will ever be on the way. -- Do you guys have any ideas on how to figure out what we have? Thanks as always for all the help, and I'm looking forward to the day when I know enough to start contributing back to the site, Josh

  Read the article

• ESX 4.0 space: DASD, NAS, or ?

  - by thormj

  I put together an ESX box for better management, but its performance is a WTF item; I'm a noob at dealing with ESX, so I'm looking for a laundry-list of reading material to help me straighten this out so I can go back to .NET programming. Current storage system: We're running Raid5+Hotspare (8x500 GB spindles) on a PERC6i on a Dell 2910. Due to ESX limitatios, the PERC is showing the storage as 1x2TB + 1x800GB "partitions." I'm not sure of the setup's configuration (stride / stripe / ???) at all. Our Applications We have a SBS server as well as a minor (2x50 GB, but growing at 10GB/month) database server... Our application that lives on the database VM is CPU and I/O insense; it's a database churning excercise mixed in with a lot of computation on the data (fixing that performance is what I'm supposed to be working on)... Perfomance Issue When I do a backup, restore, or worse (copy a backup from 1 vm to another to move it to the QA VM), the entire system slows to a crawl (even "unrelated" VMs). I originally thought a DASD situation would be quite good since you had PCI-x bandwidth, but the systemwide slowdown is killing productivity. Questions What should I do to make an intelligent decision about NAS vs RAID vs SAN vs DASD? Are there sweet spots/ugly spots in the storage setup? Can you use a SSD PCI-X card in ESX for the tempdb? Good/Bad idea? Is there any way to "share" some image in a copy-on-write fashion? Most of the "Backup-Copy-Restore" is to "put a clean image on the dev boxes"; if I could have them "share" the master image, the "big copy" (2x50 GB) would only need to be done once per week instead of once per dev per week...[runtime performance isn't a concern with the dev boxes, but the backup/copy/restore kills production, SBS, and everything else on the box]

  Read the article

• AMD 700, 800 series chipset. I'm lost.

  - by Shiki

  I've been an Intel / NVidia user ever since I started using computers. Intel really gone up with the prices, and they won't get cheaper. So I decided to get an AMD. But WHICH one? I mean.. not shopping question but.. what are the differences? Like: 880GMA comes only with a single PCI ex and it looks like a chinese replica (no offense). While 890FX comes with 5PCI-ex for QuadCrossfire. Also.. what's the deal with 7xx series? I mean.. its the same price. Yet its older? Or why is it 7xx? Isn't there a single chipset between? Not chinese YET it's durable/fine for long-term usage? What it should know (desktop stuff): NVidia GPU (Zalman AMP2 GTX 260^2 (one card)) Phenom 1090T cpu A somewhat good audio. Any ideas which is the chipset I'm searching for? If this sounds too much of a shopping question, feel free to edit. I just want some clarification on these chipsets.

  Read the article

• Better approach to archiving large amounts of original video footage using optical media (DVD/Blu-ra

  - by Rob

  This question is to share my experience as well as ask for suggestions for better methods. Along with 2 friends, I completed the making of a short documentary film in 2006. Clip is at: http://www.youtube.com/mediamotioninvision The film was edited in Adobe Premiere Pro 1.5 on Windows XP. More details and screenshot here: http://www.flickr.com/photos/smilingrobbie/1350235514/ ( note this is not intended to be a plug, we've moved on from this initial learning curve project ;) ) The film is in 4:3 standard definition 720x576 PAL format. As well as retaining the final 30minute film, I wanted to keep all original files that assembled together to make the film. The footage was 83.5Gb So I archived them to over 20 4.7Gb DVD recordables in the original .avi format (i.e. data DVD-ROM format, NOT DVD-Video Mpeg2) Some .avi DV video files were larger than 4.7Gb so I used 7-zip to split them ( here is a guide as to how to do that: http://www.linglom.com/2008/10/12/how-to-split-a-large-file-using-7-zip/ ) To recombine them, a dos shell command like this would do that: copy /b file.avi.* file.avi would do the job, where .* is a wild card to include all the split parts e.g. 001, 002...00n assuming they are all in the same directory path folder. file.avi is the recombined file identical to the original. Later on, I bought a LG BE06 LU10 USB 2.0 Super-multi Blu-ray burner and archived the footage to 2 (two) x 50Gb BD-R DL discs. Again in the original format, written as files to a BD-R in the BD-R BD-ROM UDF format readable by PC/Mac etc, NOT Blu-ray video/film format. This seems to be a good solution for me, because: the archive is in a robust, reasonably permanent, non-volatile medium, i.e. DVD recordable / Blu-ray (debates about stability of optical media organic chemical dye compounds/substrates aside) the format of the archive is accessible by open source tools or just plain Windows Explorer and it's not in a proprietary format I just thought I'd ask folks for their experience on better methods, if such exist.

  Read the article

• Internet Radio Station for University

  - by ryan

  I am trying to help my University Student Radio station rethink the setup of the way they stream music, but I have some questions regarding the use of Ubuntu to stream music. Currently, the radio station uses two windows machines: one of which is used to stream the radio station and serve the website, and the other is used by rotating djs to select songs and create playlists. The computer used by djs feeds mono into the sound card of the server and the server streams the feed online. -Ideally I would like to maintain a two-computer setup: One computer as server, and another that is used to select and play music by rotating djs. -I would like to use Ubuntu for the server. -I would like to use Windows for the other machine. -The server should be able to stream song information. First, is there a way to somehow get the song information from an analog feed? Second, what is the best streaming server for radio? I have encountered shoutcast, icecast, and darwin, but I don't know where to begin in attempting to gauge them. Finally, if anyone has any tips or pointers about small internet radio station management/ setup they would be appreciated as this is my first radio station, and I am eager to hear of past experiences.

  Read the article

• Virtual Wifi Issue Windows 7

  - by Matt

  Lately I've been trying to use my laptop as a wireless router in my room. I have it connected to my school's network through ethernet, and I want to set up wireless so that I can use Wifi on my Android phone and iPod Touch. In the past, I used Connectify, but I started having an issue where my phone would find the network, connect, attempt to get the IP, and then suddenly the network would disappear. Then it'd pop up again, and the same process would happen over and over. I decided that I'd totally uninstall Connectify, but after that, neither Virtual Router Manager nor the command prompt could create a viable network either. My phone and even my iPod now encounter the same problem. Neither can successfully connect. So evidently there is something wrong with the laptop's virtual wifi feature, and I have no idea what that could be. I've tried enabling certain services that virtual wifi supposedly relies on, but some of them don't start, namely Remote Access Connection Manager. But I also have read that these enable on their own and that if they are normally not enabled it's fine. Furthermore, I even uninstalled and reinstalled the drivers for my wireless card. Any ideas as to why my virtual wifi won't function? Anything? I really would love to get this working...

  Read the article

• Windows 7 blank dvi screen

  - by user99

  I've just upgraded to Windows 7 Ultimate 64 bit. I had an issue during installation; after setup rebooted instead of going to the 'Completing installation' screen I just got a blank screen. I eventually(!) figured out that this meant 'un-plug your second monitor to proceed'. When I did this, installation completed in a snap and everything runs fine. However, whenever I plug my second monitor into my PC, it gets no signal, the the primary monitor removes all windows. icons, the taskbar and the cursor just shows the desktop wallpaper. I'm running a GTS8800 512mb, with the latest drivers (197 IIRC). The monitors are identical, and both plug into DVI sockets on the graphics card, the only difference is I connect one using a straight DVI cable and the other using a VGA cable and a VGA-DVI converter. It's the DVI cabled one that has the issues (if I plug it in by itself it gets no signal). Everything was working fine before I upgraded to Windows 7 (I used to run XPSP2). Anyone have any ideas?

  Read the article

• Dealing with AVCHD. Any free software to extract or edit AVCHD video?

  - by Kelsey

  I have a Panasonic HDC-SD5 video carmera which records in HD format to a memory card. It also came with a DVD burner which burns this format to DVD which I need a blu-ray player to view. I can get about 30 min worth of video on 1 DVD. My problem is the software that comes with the camera is not very good at all so I am constantly just using the 'backup' feature in the included burner (connect drive to camera, push backup, and it spits out up to 4 DVDs worth of HD video). Now that I have the video backed up on DVD in the HD format (blu-ray), is there any free software that I can use to edit this video and create other HD DVD's with my own menus, transitions, etc? I was considering buying Pinnacle Studio but I wanted to exaust any free options before biting the bullet. Any suggestions for software I could use or anything else I could do to make dealing with this AVCHD format any easier that I am unaware of? Edit: Sorry forgot to include that I am running Windows Vista 64-bit. Edit: Still haven't found anything that is truely free. Everything has limitations by either time, watermark the video or degrade the quality. Edit: So I still haven't found really anything, so is there some software I can use to convert the video to another format that I then could use to edit the video?

  Read the article

• BIOS unable to boot CD or Hard Drive

  - by Gabriel

  Motherboard Intel DQ35MP. HDD Caviar Green 1TB. I'm having problems with my BIOS and/or hard drive/disc drive. Came back from a trip, booted my computer, and realized that the BIOS wasn't booting anymore, just a black screen with no beep sounds. Only fans and lights on. Then I thought it might be caused by the video card, I removed it, and still no BIOS screen. Then I removed the hard drive and voila BIOS screen is back again. If the hard drive is defective then I can check that with a Rescue Disk. I inserted the CD on the Disc Tray but the computer did not respond to it, the screen freezes in black with an "E7" string at the bottom right corner just after the BIOS screen, this happens with or without discs. BIOS settings are set to default, and CD reading is on top of the boot device list. EDIT I removed the BIOS battery, rebooted the CPU, the BIOS screen showed up, and then it freezed in E7. Placed the BIOS batttery, rebooted and same thing, we are stuck with the E7 string. I uploaded a video to illustrate the problem http://www.youtube.com/watch?v=13jPdBcIrBU

  Read the article

• Netgear GS724Tv3 and link aggregation Mac OS X Server 10.6.8

  - by Manca Weeks

  I need to link aggregate 2 sets of ports on the Netgear GS724T with my Apple server tower (latest generation). I have 2 built in ports and 2 ports on a PCIe ethernet card. It is not obvious to me how to properly configure the Netgear end. I have access to the Netgear box through its web interface, just don't know how to properly set the settings. I tried going to Netgear for help, but they said my software support has expired. I bought this unit on their recommendation - they say it is compatible with 802.3ad protocol. I cannot locate any references to this protocol in the manual and I noticed some people in formus say that this device is actually not compatible with 802.3ad and that Netgear is misleading potential customers by saying it is. Any help will be appreciated. Thanks, M My own answer - posted as edit because of restrictions on my user: OK folks, turns out one must use a Windows machine on this one or nothing makes sense. I was unable to get much farther than viewing the default inactive LAGs because in Firefox and Safari on Mac things don't make much sense - i.e. the Apply buttons (supposedly JavaScript) don't work. You can view the configurations, but none of the modifications you make stick. Then, in Switching - LAGs, choose the ports to include and make sure you switch the LAG type from Static to LACP and all is well. Haven't tested the performance of the config yet, but both sides appear to be happy with the configuration. Apple server says link active and so does the Netgear. Will report if any other discoveries. Thanks for all who read and to user84104 for responding. M

  Read the article

< Previous Page | 213 214 215 216 217 218 219 220 221 222 223 224  | Next Page >