Search Results

Search found 708 results on 29 pages for 'beaso 88'.

Page 22/29 | < Previous Page | 18 19 20 21 22 23 24 25 26 27 28 29  | Next Page >

• Site-to-site VPN using MD5 instead of SHA and getting regular disconnection

  - by Steven

  We are experiencing some strange behavior with a site-to-site IPsec VPN that goes down about every week for 30 minutes (Iam told 30 minutes exactly). I don't have access to the logs, so it's difficult to troubleshoot. What is also strange is that the two VPN devices are set to use SHA hash algorithm but apparently end up agreeing to use MD5. Does anybody have a clue? or is this just insufficient information? Edit: Here is an extract of the log of one of the two VPN devices, which is a Cisco 3000 series VPN concentrator. 27981 03/08/2010 10:02:16.290 SEV=4 IKE/41 RPT=16120 xxxxxxxx IKE Initiator: New Phase 1, Intf 2, IKE Peer xxxxxxxx local Proxy Address xxxxxxxx, remote Proxy Address xxxxxxxx, SA (L2L: 1A) 27983 03/08/2010 10:02:56.930 SEV=4 IKE/41 RPT=16121 xxxxxxxx IKE Initiator: New Phase 1, Intf 2, IKE Peer xxxxxxxx local Proxy Address xxxxxxxx, remote Proxy Address xxxxxxxx, SA (L2L: 1A) 27986 03/08/2010 10:03:35.370 SEV=4 IKE/41 RPT=16122 xxxxxxxx IKE Initiator: New Phase 1, Intf 2, IKE Peer xxxxxxxx local Proxy Address xxxxxxxx, remote Proxy Address xxxxxxxx, SA (L2L: 1A) [… same continues for another 15 minutes …] 28093 03/08/2010 10:19:46.710 SEV=4 IKE/41 RPT=16140 xxxxxxxx IKE Initiator: New Phase 1, Intf 2, IKE Peer xxxxxxxx local Proxy Address xxxxxxxx, remote Proxy Address xxxxxxxx, SA (L2L: 1A) 28096 03/08/2010 10:20:17.720 SEV=5 IKE/172 RPT=1291 xxxxxxxx Group [xxxxxxxx] Automatic NAT Detection Status: Remote end is NOT behind a NAT device This end IS behind a NAT device 28100 03/08/2010 10:20:17.820 SEV=3 IKE/134 RPT=79 xxxxxxxx Group [xxxxxxxx] Mismatch: Configured LAN-to-LAN proposal differs from negotiated proposal. Verify local and remote LAN-to-LAN connection lists. 28103 03/08/2010 10:20:17.820 SEV=4 IKE/119 RPT=1197 xxxxxxxx Group [xxxxxxxx] PHASE 1 COMPLETED 28104 03/08/2010 10:20:17.820 SEV=4 AUTH/22 RPT=1031 xxxxxxxx User [xxxxxxxx] Group [xxxxxxxx] connected, Session Type: IPSec/LAN- to-LAN 28106 03/08/2010 10:20:17.820 SEV=4 AUTH/84 RPT=39 LAN-to-LAN tunnel to headend device xxxxxxxx connected 28110 03/08/2010 10:20:17.920 SEV=5 IKE/25 RPT=1291 xxxxxxxx Group [xxxxxxxx] Received remote Proxy Host data in ID Payload: Address xxxxxxxx, Protocol 0, Port 0 28113 03/08/2010 10:20:17.920 SEV=5 IKE/24 RPT=88 xxxxxxxx Group [xxxxxxxx] Received local Proxy Host data in ID Payload: Address xxxxxxxx, Protocol 0, Port 0 28116 03/08/2010 10:20:17.920 SEV=5 IKE/66 RPT=1290 xxxxxxxx Group [xxxxxxxx] IKE Remote Peer configured for SA: L2L: 1A 28117 03/08/2010 10:20:17.930 SEV=5 IKE/25 RPT=1292 xxxxxxxx Group [xxxxxxxx] Received remote Proxy Host data in ID Payload: Address xxxxxxxx, Protocol 0, Port 0 28120 03/08/2010 10:20:17.930 SEV=5 IKE/24 RPT=89 xxxxxxxx Group [xxxxxxxx] Received local Proxy Host data in ID Payload: Address xxxxxxxx, Protocol 0, Port 0 28123 03/08/2010 10:20:17.930 SEV=5 IKE/66 RPT=1291 xxxxxxxx Group [xxxxxxxx] IKE Remote Peer configured for SA: L2L: 1A 28124 03/08/2010 10:20:18.070 SEV=4 IKE/173 RPT=17330 xxxxxxxx Group [xxxxxxxx] NAT-Traversal successfully negotiated! IPSec traffic will be encapsulated to pass through NAT devices. 28127 03/08/2010 10:20:18.070 SEV=4 IKE/49 RPT=17332 xxxxxxxx Group [xxxxxxxx] Security negotiation complete for LAN-to-LAN Group (xxxxxxxx) Responder, Inbound SPI = 0x56a4fe5c, Outbound SPI = 0xcdfc3892 28130 03/08/2010 10:20:18.070 SEV=4 IKE/120 RPT=17332 xxxxxxxx Group [xxxxxxxx] PHASE 2 COMPLETED (msgid=37b3b298) 28131 03/08/2010 10:20:18.750 SEV=4 IKE/41 RPT=16141 xxxxxxxx Group [xxxxxxxx] IKE Initiator: New Phase 2, Intf 2, IKE Peer xxxxxxxx local Proxy Address xxxxxxxx, remote Proxy Address xxxxxxxx, SA (L2L: 1A) 28135 03/08/2010 10:20:18.870 SEV=4 IKE/173 RPT=17331 xxxxxxxx Group [xxxxxxxx] NAT-Traversal successfully negotiated! IPSec traffic will be encapsulated to pass through NAT devices.

  Read the article

• Call to daemon in a /etc/init.d script is blocking, not running in background

  - by tony

  I have a Perl script that I want to daemonize. Basically this perl script will read a directory every 30 seconds, read the files that it finds and then process the data. To keep it simple here consider the following Perl script (called synpipe_server, there is a symbolic link of this script in /usr/sbin/) : #!/usr/bin/perl use strict; use warnings; my $continue = 1; $SIG{'TERM'} = sub { $continue = 0; print "Caught TERM signal\n"; }; $SIG{'INT'} = sub { $continue = 0; print "Caught INT signal\n"; }; my $i = 0; while ($continue) { #do stuff print "Hello, I am running " . ++$i . "\n"; sleep 3; } So this script basically prints something every 3 seconds. Then, as I want to daemonize this script, I've also put this bash script (also called synpipe_server) in /etc/init.d/ : #!/bin/bash # synpipe_server : This starts and stops synpipe_server # # chkconfig: 12345 12 88 # description: Monitors all production pipelines # processname: synpipe_server # pidfile: /var/run/synpipe_server.pid # Source function library. . /etc/rc.d/init.d/functions pname="synpipe_server" exe="/usr/sbin/synpipe_server" pidfile="/var/run/${pname}.pid" lockfile="/var/lock/subsys/${pname}" [ -x $exe ] || exit 0 RETVAL=0 start() { echo -n "Starting $pname : " daemon ${exe} RETVAL=$? PID=$! echo [ $RETVAL -eq 0 ] && touch ${lockfile} echo $PID > ${pidfile} } stop() { echo -n "Shutting down $pname : " killproc ${exe} RETVAL=$? echo if [ $RETVAL -eq 0 ]; then rm -f ${lockfile} rm -f ${pidfile} fi } restart() { echo -n "Restarting $pname : " stop sleep 2 start } case "$1" in start) start ;; stop) stop ;; status) status ${pname} ;; restart) restart ;; *) echo "Usage: $0 {start|stop|status|restart}" ;; esac exit 0 So, (if I have well understood the doc for daemon) the Perl script should run in the background and the output should be redirected to /dev/null if I execute : service synpipe_server start But here is what I get instead : [root@master init.d]# service synpipe_server start Starting synpipe_server : Hello, I am running 1 Hello, I am running 2 Hello, I am running 3 Hello, I am running 4 Caught INT signal [ OK ] [root@master init.d]# So it starts the Perl script but runs it without detaching it from the current terminal session, and I can see the output printed in my console ... which is not really what I was expecting. Moreover, the PID file is empty (or with a line feed only, no pid returned by daemon). Does anyone have any idea of what I am doing wrong ? EDIT : maybe I should say that I am on a Red Hat machine. Scientific Linux SL release 5.4 (Boron) Would it do the job if instead of using the daemon function, I use something like : nohup ${exe} >/dev/null 2>&1 & in the init script ?

  Read the article

• How to place SuperFetch cache on an SSD?

  - by Ian Boyd

  I'm thinking of adding a solid state drive (SSD) to my existing Windows 7 installation. I know I can (and should) move my paging file to the SSD: Should the pagefile be placed on SSDs? Yes. Most pagefile operations are small random reads or larger sequential writes, both of which are types of operations that SSDs handle well. In looking at telemetry data from thousands of traces and focusing on pagefile reads and writes, we find that Pagefile.sys reads outnumber pagefile.sys writes by about 40 to 1, Pagefile.sys read sizes are typically quite small, with 67% less than or equal to 4 KB, and 88% less than 16 KB. Pagefile.sys writes are relatively large, with 62% greater than or equal to 128 KB and 45% being exactly 1 MB in size. In fact, given typical pagefile reference patterns and the favorable performance characteristics SSDs have on those patterns, there are few files better than the pagefile to place on an SSD. What I don't know is if I even can put a SuperFetch cache (i.e. ReadyBoost cache) on the solid state drive. I want to get the benefit of Windows being able to cache gigabytes of frequently accessed data on a relativly small (e.g. 30GB) solid state drive. This is exactly what SuperFetch+ReadyBoost (or SuperFetch+ReadyDrive) was designed for. Will Windows offer (or let) me place a ReadyBoost cache on a solid state flash drive connected via SATA? A problem with the ReadyBoost cache over the ReadyDrive cache is that the ReadyBoost cache does not survive between reboots. The cache is encrypted with a per-session key, making its existing contents unusable during boot and SuperFetch pre-fetching during login. Update One I know that Windows Vista limited you to only one ReadyBoost.sfcache file (I do not know if Windows 7 removed that limitation): Q: Can use use multiple devices for EMDs? A: Nope. We've limited Vista to one ReadyBoost per machine Q: Why just one device? A: Time and quality. Since this is the first revision of the feature, we decided to focus on making the single device exceptional, without the difficulties of managing multiple caches. We like the idea, though, and it's under consideration for future versions. I also know that the 4GB limit on the cache file was a limitation of the FAT filesystem used on most USB sticks - an SSD drive would be formatted with NTFS: Q: What's the largest amount of flash that I can use for ReadyBoost? A: You can use up to 4GB of flash for ReadyBoost (which turns out to be 8GB of cache w/ the compression) Q: Why can't I use more than 4GB of flash? A: The FAT32 filesystem limits our ReadyBoost.sfcache file to 4GB Can a ReadyBoost cache on an NTFS volume be larger than 4GB? Update Two The ReadyBoost cache is encrypted with a per-boot session key. This means that the cache has to be re-built after each boot, and cannot be used to help speed boot times, or latency from login to usable. Windows ReadyDrive technology takes advantage of non-volatile (NV) memory (i.e. flash) that is incorporated with some hybrid hard drives. This flash cache can be used to help Windows boot, or resume from hibernate faster. Will Windows 7 use an internal SSD drive as a ReadyBoost/*ReadyDrive*/SuperFetch cache? Is it possible to make Windows store a SuperFetch cache (i.e. ReadyBoost) on a non-removable SSD? Is it possible to not encrypt the ReadyBoost cache, and if so will Windows 7 use the cache at boot time? See also SuperUser.com: ReadyBoost + SSD = ? Windows 7 - ReadyBoost & SSD drives? Support and Q&A for Solid-State Drives Using SDD as a cache for HDD, is there a solution? Performance increase using SSD for paging/fetch/cache or ReadyBoost? (Win7) Windows 7 To Boost SSD Performance How to Disable Nonvolatile Caching

  Read the article

• Why would VMWare to go defunct? How to recover from/prevent it?

  - by Josh

  I am running VMWare Server 2.0.2 (Build 203138) on a dual core Intel i5 with Ubuntu Server 10.04 LTS system (kernel 2.6.32-22-server #33-Ubuntu SMP). Disk Subsystem is a software RAID5 array. The system has been set up for a little over a week. For the past 5 days I have been running at leat 3 VMs (Linux and a variety of Windows OSes) with no issues whatsoever. But while I was installing Linux onto a new VM, suddenly all VMs became unresponsive, including the one I was installing to. I could not log in to the VMWare Management Interface, and the system was somewhat unresponsive via SSH. When I looked at top, I saw: top - 16:14:51 up 6 days, 1:49, 8 users, load average: 24.29, 24.33 17.54 Tasks: 203 total, 7 running, 195 sleeping, 0 stopped, 1 zombie Cpu(s): 0.2%us, 25.6%sy, 0.0%ni, 74.3%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 8056656k total, 5927580k used, 2129076k free, 20320k buffers Swap: 7811064k total, 240216k used, 7570848k free, 5045884k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 21549 root 39 19 0 0 0 Z 100 0.0 15:02.44 [vmware-vmx] <defunct> 2115 root 20 0 0 0 0 S 1 0.0 170:32.08 [vmware-rtc] 2231 root 21 1 1494m 126m 100m S 1 1.6 892:58.05 /usr/lib/vmware/bin/vmware-vmx -# product=2; 2280 jnet 20 0 19320 1164 800 R 0 0.0 30:04.55 top 12236 root 20 0 833m 41m 34m S 0 0.5 88:34.24 /usr/lib/vmware/bin/vmware-vmx -# product=2; 1 root 20 0 23704 1476 920 S 0 0.0 0:00.80 /sbin/init 2 root 20 0 0 0 0 S 0 0.0 0:00.01 [kthreadd] 3 root RT 0 0 0 0 S 0 0.0 0:00.00 [migration/0] 4 root 20 0 0 0 0 S 0 0.0 0:00.84 [ksoftirqd/0] 5 root RT 0 0 0 0 S 0 0.0 0:00.00 [watchdog/0] 6 root RT 0 0 0 0 S 0 0.0 0:00.00 [migration/1] The VMWare process for the virtual machine I was installing into became a zombie. Yet, it was still consuming 100% of the CPU time on one of the cores, and I couldn't reach it or any other virtual machines. (I was logged in to one virtual machine over SSH, another via X11, and a third via VNC. All three connections died). When I ran ps -ef and similar commands, I found that the defunct vmware-vmx process had it's parent PID set to init (1). I also used lsof -p 21549 and found that the defunct process had no open files. Yet it was using 100% of CPU time... I was unable to kill any vmware-vmx processes, including the defunct one, even with kill -9. As a last resort to resolve the situation I tried to reboot the box, however shutdown, halt, reboot, and init 6 all failed to reboot/shutdown, even when given appropriate --force settings. ControlAltDel produced a message about rebooting on the console, but the system would not reboot. I had to hard power-cycle the box to resolve the situation. (See my other question, Should I worry about the integrity of my linux software RAID5 after a crash or kernel panic?) What would cause a scenario like this? What else could I have done to resolve it besides a hard reboot? What can I do to prevent such a situation in the future?

  Read the article

• DNS with name.com and Amazon S3

  - by aledalgrande

  I have a website on a bucket in Amazon S3, and recently started to get emails from Google "Googlebot can't access your site". When I go to Webmaster Tools and I try to fetch in fact it doesn't work. Also people in locations different from mine sometimes reported they could not access the website. Now for curiosity I tried from my terminal: $ host xxx xxx is an alias for xxx.s3-website-us-west-1.amazonaws.com. xxx.s3-website-us-west-1.amazonaws.com is an alias for s3-website-us-west-1.amazonaws.com. s3-website-us-west-1.amazonaws.com has address yyy.yyy.yyy.yyy And when I try with dig: $ dig xxx ; <<>> DiG 9.8.3-P1 <<>> xxx ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 17860 ;; flags: qr rd ra; QUERY: 1, ANSWER: 3, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;xxx. IN A ;; ANSWER SECTION: xxx. 300 IN CNAME xxx.s3-website-us-west-1.amazonaws.com. xxx.s3-website-us-west-1.amazonaws.com. 60 IN CNAME s3-website-us-west-1.amazonaws.com. s3-website-us-west-1.amazonaws.com. 60 IN A yyy ;; Query time: 1514 msec ;; SERVER: 75.75.75.75#53(75.75.75.75) ;; WHEN: Fri Aug 22 12:32:13 2014 ;; MSG SIZE rcvd: 127 It seems OK to me. Why would Google tell me there is a DNS error? UPDATE: Google also cannot fetch robots.txt, but I can fetch it from my browser. UPDATE 2: I have a forwarding on the root to the www.* hostname: $ dig thenifty.me ; <<>> DiG 9.8.3-P1 <<>> thenifty.me ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 49286 ;; flags: qr rd ra; QUERY: 1, ANSWER: 0, AUTHORITY: 1, ADDITIONAL: 0 ;; QUESTION SECTION: ;thenifty.me. IN A ;; AUTHORITY SECTION: thenifty.me. 300 IN SOA ns1hwy.name.com. support.name.com. 1 10800 3600 604800 300 ;; Query time: 148 msec ;; SERVER: 75.75.75.75#53(75.75.75.75) ;; WHEN: Fri Aug 22 13:32:56 2014 ;; MSG SIZE rcvd: 88

  Read the article

• Samba with Active Directory - shares are readonly, NT_STATUS_MEDIA_WRITE_PROTECTED

  - by froh42

  I've set a samba server that seems to work, all shares are seemingly exported as readonly, however. The machine is called "lx". When I'm on lx I can run the following command: froh@lx:~$ smbclient //lx/export -UAdministrator Enter Administrator's password: Domain=[CUSTOMER] OS=[Unix] Server=[Samba 3.5.4] smb: \> mkdir wrzlbrmpf NT_STATUS_MEDIA_WRITE_PROTECTED making remote directory \wrzlbrmpf smb: \> ls . D 0 Fri Dec 3 19:04:20 2010 .. D 0 Sun Nov 28 01:32:37 2010 zork D 0 Fri Dec 3 18:53:33 2010 bar D 0 Sun Nov 28 23:52:43 2010 ork 1 Fri Dec 3 18:53:02 2010 foo 1 Sun Nov 28 23:52:41 2010 gaga D 0 Fri Dec 3 19:04:20 2010 How can I troubleshoot this? What I did: First I set up a fresh install of Ubuntu 10.10 x64. Second I got kerberos working with the following krb5.conf file: [libdefaults] ticket_lifetime = 24000 clock_skew = 300 default_realm = CUSTOMER.LOCAL [realms] CUSTOMER.LOCAL = { kdc = SB4.customer.local:88 admin_server = SB4.customer.local:464 default_domain = CUSTOMER.LOCAL } [domain_realm] .customer.local = CUSTOMER.LOCAL customer.local = CUSTOMER.LOCAL #[login] # krb4_convert = true # krb4_get_tickets = false I also added winbind to group, passwd and shadow in nsswitch.conf. Seemingly Kerberos works: root@lx:~# net ads testjoin Join is OK root@lx:~# wbinfo -a 'Administrator%MYSECRETPASSWORD' plaintext password authentication succeeded challenge/response password authentication succeeded wbinfo -u and wbinfo -g also spit out a list of users and a list of groups respectiveley. I noted that domain accounts did NOT include a domain and they are in german (as on the SBS 2003 that is the domain server). So I get a "Domänenbenutzer" in wbinfo -u's output not a "CUSTOMER+Domain User" or something similar. I'm not sure anymore what I did to the PAM configuration, but here is what I currently have: root@lx:/etc/pam.d# cat samba @include common-auth @include common-account @include common-session-noninteractive root@lx:/etc/pam.d# grep -ve '^#' common-auth auth [success=3 default=ignore] pam_krb5.so minimum_uid=1000 auth [success=2 default=ignore] pam_unix.so nullok_secure try_first_pass auth [success=1 default=ignore] pam_winbind.so krb5_auth krb5_ccache_type=FILE cached_login try_first_pass auth requisite pam_deny.so auth required pam_permit.so root@lx:/etc/pam.d# grep -ve '^#' common-account account [success=2 new_authtok_reqd=done default=ignore] pam_unix.so account [success=1 new_authtok_reqd=done default=ignore] pam_winbind.so account requisite pam_deny.so account required pam_permit.so account required pam_krb5.so minimum_uid=1000 root@lx:/etc/pam.d# grep -ve '^#' common-session-noninteractive session [default=1] pam_permit.so session requisite pam_deny.so session required pam_permit.so session optional pam_krb5.so minimum_uid=1000 session required pam_unix.so session optional pam_winbind.so At some point I joined the linux box into the AD domain. After (manually) creating a home directory on the linux box I can log in using the Adminstrator user with the password taken from AD. Now I run samba with the following setup: [global] netbios name = LX realm = CUSTOMER.LOCAL workgroup = CUSTOMER security = ADS encrypt passwords = yes password server = 192.168.20.244 #IP des Domain Controllers os level = 0 socket options = TCP_NODELAY SO_RCVBUF=16384 SO_SNDBUF=16384 idmap uid = 10000-20000 idmap gid = 10000-20000 winbind enum users = Yes winbind enum groups = Yes preferred master = no winbind separator = + dns proxy = no wins proxy = no # client NTLMv2 auth = Yes log level = 2 logfile = /var/log/samba/log.smbd.%U template homedir = /home/%U template shell = /bin/bash [export] path = /mnt/sdc1/export read only = No public = Yes Currently I don't care whether export is exported to everyone or just one user, I want to see somebody WRITING to that directory before I start fiddling with the authentication settings. (Who may access it). As mentioned, accessing the share from smbclient results in this NT_STATUS_MEDIA_WRITE_PROTECTED . Accessing it from windows shows ACLs that look correct (The user may write) - but it does not work, I can only read files not write. The directory to be exported looks like this: root@lx:/etc/pam.d# ls -ld /mnt/ drwxr-xr-x 5 root root 4096 2010-11-28 01:29 /mnt/ root@lx:/etc/pam.d# ls -ld /mnt/sdc1/ drwxr-xr-x 4 froh froh 4096 2010-11-28 01:32 /mnt/sdc1/ root@lx:/etc/pam.d# ls -ld /mnt/sdc1/export/ drwxrwxrwx+ 5 administrator domänen-admins 4096 2010-12-03 19:04 /mnt/sdc1/export/ root@lx:/etc/pam.d# getfacl /mnt/ getfacl: Entferne führende '/' von absoluten Pfadnamen # file: mnt/ # owner: root # group: root user::rwx group::r-x other::r-x root@lx:/etc/pam.d# getfacl /mnt/sdc1/ getfacl: Entferne führende '/' von absoluten Pfadnamen # file: mnt/sdc1/ # owner: froh # group: froh user::rwx group::r-x other::r-x root@lx:/etc/pam.d# getfacl /mnt/sdc1/export/ getfacl: Entferne führende '/' von absoluten Pfadnamen # file: mnt/sdc1/export/ # owner: administrator # group: domänen-admins user::rwx group::rwx group:domänen-admins:rwx mask::rwx other::rwx default:user::rwx default:group::rwx default:group:domänen-admins:rwx default:mask::rwx default:other::rwx My, oh my what am I overlooking? What am I to blind to see?

  Read the article

• Excessive denied requests for port 58322 in syslog

  - by Nathan C.

  My iptables is setup to block all unneeded ports as it should but I'm checking my syslog due to these random but all-to-frequent apache2 crashes and I noticed a lot of requests such as this. In all the archived syslogs that I have these are present from different IP addresses. There is a similar question with an accepted here: What service uses UDP port 60059? Jun 4 06:49:27 HOSTNAME kernel: iptables denied: IN=eth0 OUT= MAC=fe:fd:ad:ff:dd:95:c8:4c:75:f5:d6:3f:08:00 SRC=218.7.74.50 DST=MY.SERVER.IP.HERE LEN=129 TOS=0x00 PREC=0x00 TTL=115 ID=27636 PROTO=UDP SPT=9520 DPT=58322 LEN=109 Jun 4 06:49:31 HOSTNAME kernel: iptables denied: IN=eth0 OUT= MAC=fe:fd:ad:ff:dd:95:c8:4c:75:f5:d6:3f:08:00 SRC=95.160.226.177 DST=MY.SERVER.IP.HERE LEN=131 TOS=0x00 PREC=0x00 TTL=116 ID=31468 PROTO=UDP SPT=47642 DPT=58322 LEN=111 Jun 4 06:49:54 HOSTNAME kernel: iptables denied: IN=eth0 OUT= MAC=fe:fd:ad:ff:dd:95:c8:4c:75:f5:d6:3f:08:00 SRC=78.137.36.10 DST=MY.SERVER.IP.HERE LEN=131 TOS=0x00 PREC=0x00 TTL=118 ID=21872 PROTO=UDP SPT=57872 DPT=58322 LEN=111 Jun 4 06:50:14 HOSTNAME kernel: iptables denied: IN=eth0 OUT= MAC=fe:fd:ad:ff:dd:95:c8:4c:75:f5:d6:3f:08:00 SRC=111.253.217.11 DST=MY.SERVER.IP.HERE LEN=131 TOS=0x00 PREC=0x00 TTL=116 ID=28882 PROTO=UDP SPT=51826 DPT=58322 LEN=111 Jun 4 06:51:02 HOSTNAME kernel: iptables denied: IN=eth0 OUT= MAC=fe:fd:ad:ff:dd:95:c8:4c:75:f5:d6:3f:08:00 SRC=189.45.114.173 DST=MY.SERVER.IP.HERE LEN=131 TOS=0x16 PREC=0x00 TTL=113 ID=19985 PROTO=UDP SPT=41087 DPT=58322 LEN=111 Jun 4 06:51:09 HOSTNAME kernel: iptables denied: IN=eth0 OUT= MAC=fe:fd:ad:ff:dd:95:c8:4c:75:f5:d6:3f:08:00 SRC=87.89.202.28 DST=MY.SERVER.IP.HERE LEN=131 TOS=0x00 PREC=0x00 TTL=116 ID=7874 PROTO=UDP SPT=17524 DPT=58322 LEN=111 Jun 4 06:51:20 HOSTNAME kernel: iptables denied: IN=eth0 OUT= MAC=fe:fd:ad:ff:dd:95:c8:4c:75:f5:d6:3f:08:00 SRC=24.44.124.35 DST=MY.SERVER.IP.HERE LEN=131 TOS=0x00 PREC=0x00 TTL=118 ID=12978 PROTO=UDP SPT=45596 DPT=58322 LEN=111 Jun 4 06:51:22 HOSTNAME kernel: iptables denied: IN=eth0 OUT= MAC=fe:fd:ad:ff:dd:95:c8:4c:75:f5:d6:3f:08:00 SRC=81.174.48.236 DST=MY.SERVER.IP.HERE LEN=93 TOS=0x00 PREC=0x00 TTL=48 ID=0 DF PROTO=UDP SPT=21352 DPT=58322 LEN=73 Jun 4 06:51:23 HOSTNAME kernel: iptables denied: IN=eth0 OUT= MAC=fe:fd:ad:ff:dd:95:c8:4c:75:f5:d6:3f:08:00 SRC=124.107.61.84 DST=MY.SERVER.IP.HERE LEN=131 TOS=0x00 PREC=0x00 TTL=114 ID=13038 PROTO=UDP SPT=14357 DPT=58322 LEN=111 Jun 4 06:51:30 HOSTNAME kernel: iptables denied: IN=eth0 OUT= MAC=fe:fd:ad:ff:dd:95:c8:4c:75:f5:d6:3f:08:00 SRC=88.8.23.200 DST=MY.SERVER.IP.HERE LEN=123 TOS=0x00 PREC=0x00 TTL=117 ID=21062 PROTO=UDP SPT=4291 DPT=58322 LEN=103 Jun 4 06:51:54 HOSTNAME kernel: iptables denied: IN=eth0 OUT= MAC=fe:fd:ad:ff:dd:95:c8:4c:75:f5:d6:3f:08:00 SRC=80.202.244.234 DST=MY.SERVER.IP.HERE LEN=129 TOS=0x00 PREC=0x00 TTL=114 ID=339 PROTO=UDP SPT=14020 DPT=58322 LEN=109 I'm not overly experienced with server configuration and debugging, so I only just installed logcheck after reading that previous question. I guess my question is what steps should I take after reading this log info to 1) further protect myself, 2) understand if this could be causing any other problems with my VPS, and 3) use this data to help others?

  Read the article

• FFMPEG dropping frames while encoding JPEG sequence at color change

  - by Matt

  I'm trying to put together a slide show using imagemagick and FFMPEG. I use imagemagick to expand a single photo into 30fps video (imagemagick also handles things like putting some text captions on the frames along the way). When I go to let ffmpeg digest it into a video it clips along nicely on the color parts of the video, but when it gets to a black and white section it reports "frame= 2030 fps=102 q=32766.0 Lsize= 5203kB time=00:01:07.60 bitrate= 630.5kbits/s dup=0 drop=703" and drops every frame of video until it hits something with color. As you can imagine this results in entire photos being removed from the slideshow. Here is my latest dump... ffmpeg -y -r 30 -i "teststream/%06d.jpg" -c:v libx264 -r 30 newffmpeg.mp4 ffmpeg version git-2012-12-10-c3bb333 Copyright (c) 2000-2012 the FFmpeg developers built on Dec 10 2012 22:02:04 with gcc 4.6.1 (Ubuntu/Linaro 4.6.1-9ubuntu3) configuration: --enable-gpl --enable-libfaac --enable-libmp3lame --enable-libopencore-amrnb --enable-libopencore-amrwb --enable-librtmp --enable-libtheora --enable-libvorbis --enable-libx264 --enable-nonfree --enable-version3 libavutil 52. 12.100 / 52. 12.100 libavcodec 54. 79.101 / 54. 79.101 libavformat 54. 49.100 / 54. 49.100 libavdevice 54. 3.102 / 54. 3.102 libavfilter 3. 26.101 / 3. 26.101 libswscale 2. 1.103 / 2. 1.103 libswresample 0. 17.102 / 0. 17.102 libpostproc 52. 2.100 / 52. 2.100 Input #0, image2, from 'teststream/%06d.jpg': Duration: 00:12:02.80, start: 0.000000, bitrate: N/A Stream #0:0: Video: mjpeg, yuvj444p, 720x480 [SAR 72:72 DAR 3:2], 25 fps, 25 tbr, 25 tbn, 25 tbc [libx264 @ 0x3450140] using SAR=1/1 [libx264 @ 0x3450140] using cpu capabilities: MMX2 SSE2Fast SSSE3 FastShuffle SSE4.2 [libx264 @ 0x3450140] profile High, level 3.0 [libx264 @ 0x3450140] 264 - core 129 r2 1cffe9f - H.264/MPEG-4 AVC codec - Copyleft 2003-2012 - http://www.videolan.org/x264.html - options: cabac=1 ref=3 deblock=1:0:0 analyse=0x3:0x113 me=hex subme=7 psy=1 psy_rd=1.00:0.00 mixed_ref=1 me_range=16 chroma_me=1 trellis=1 8x8dct=1 cqm=0 deadzone=21,11 fast_pskip=1 chroma_qp_offset=-2 threads=12 lookahead_threads=2 sliced_threads=0 nr=0 decimate=1 interlaced=0 bluray_compat=0 constrained_intra=0 bframes=3 b_pyramid=2 b_adapt=1 b_bias=0 direct=1 weightb=1 open_gop=0 weightp=2 keyint=250 keyint_min=25 scenecut=40 intra_refresh=0 rc_lookahead=40 rc=crf mbtree=1 crf=23.0 qcomp=0.60 qpmin=0 qpmax=69 qpstep=4 ip_ratio=1.40 aq=1:1.00 Output #0, mp4, to 'newffmpeg.mp4': Metadata: encoder : Lavf54.49.100 Stream #0:0: Video: h264 ([33][0][0][0] / 0x0021), yuvj420p, 720x480 [SAR 1:1 DAR 3:2], q=-1--1, 15360 tbn, 30 tbc Stream mapping: Stream #0:0 - #0:0 (mjpeg - libx264) Press [q] to stop, [?] for help Input stream #0:0 frame changed from size:720x480 fmt:yuvj444p to size:720x480 fmt:yuvj422p Input stream #0:0 frame changed from size:720x480 fmt:yuvj422p to size:720x480 fmt:yuvj444pp=584 frame= 2030 fps=102 q=32766.0 Lsize= 5203kB time=00:01:07.60 bitrate= 630.5kbits/s dup=0 drop=703 video:5179kB audio:0kB subtitle:0 global headers:0kB muxing overhead 0.472425% [libx264 @ 0x3450140] frame I:9 Avg QP:20.10 size: 33933 [libx264 @ 0x3450140] frame P:636 Avg QP:24.12 size: 6737 [libx264 @ 0x3450140] frame B:1385 Avg QP:27.04 size: 514 [libx264 @ 0x3450140] consecutive B-frames: 2.5% 15.2% 13.2% 69.2% [libx264 @ 0x3450140] mb I I16..4: 8.3% 80.3% 11.5% [libx264 @ 0x3450140] mb P I16..4: 1.5% 2.5% 0.2% P16..4: 41.7% 18.0% 10.3% 0.0% 0.0% skip:25.9% [libx264 @ 0x3450140] mb B I16..4: 0.0% 0.0% 0.0% B16..8: 26.6% 0.6% 0.1% direct: 0.2% skip:72.3% L0:35.0% L1:60.3% BI: 4.7% [libx264 @ 0x3450140] 8x8 transform intra:64.1% inter:75.1% [libx264 @ 0x3450140] coded y,uvDC,uvAC intra: 51.6% 78.0% 43.7% inter: 10.6% 14.9% 2.1% [libx264 @ 0x3450140] i16 v,h,dc,p: 29% 19% 6% 46% [libx264 @ 0x3450140] i8 v,h,dc,ddl,ddr,vr,hd,vl,hu: 23% 15% 17% 5% 9% 10% 7% 8% 6% [libx264 @ 0x3450140] i4 v,h,dc,ddl,ddr,vr,hd,vl,hu: 31% 18% 11% 5% 9% 10% 6% 6% 4% [libx264 @ 0x3450140] i8c dc,h,v,p: 46% 18% 24% 12% [libx264 @ 0x3450140] Weighted P-Frames: Y:20.1% UV:18.7% [libx264 @ 0x3450140] ref P L0: 59.2% 23.2% 13.1% 4.3% 0.2% [libx264 @ 0x3450140] ref B L0: 88.7% 8.3% 3.0% [libx264 @ 0x3450140] ref B L1: 95.0% 5.0% [libx264 @ 0x3450140] kb/s:626.88 Received signal 2: terminating. One last note: If I remove the -r 30 from the input and output it works flawlessly. I have no idea why the -r 30 is causing it to freak out.

  Read the article

• Samba with Active Directory - shares are readonly, NT_STATUS_MEDIA_WRITE_PROTECTED

  - by froh42

  I've set a samba server that seems to work, all shares are seemingly exported as readonly, however. The machine is called "lx". When I'm on lx I can run the following command: froh@lx:~$ smbclient //lx/export -UAdministrator Enter Administrator's password: Domain=[CUSTOMER] OS=[Unix] Server=[Samba 3.5.4] smb: \> mkdir wrzlbrmpf NT_STATUS_MEDIA_WRITE_PROTECTED making remote directory \wrzlbrmpf smb: \> ls . D 0 Fri Dec 3 19:04:20 2010 .. D 0 Sun Nov 28 01:32:37 2010 zork D 0 Fri Dec 3 18:53:33 2010 bar D 0 Sun Nov 28 23:52:43 2010 ork 1 Fri Dec 3 18:53:02 2010 foo 1 Sun Nov 28 23:52:41 2010 gaga D 0 Fri Dec 3 19:04:20 2010 How can I troubleshoot this? What I did: First I set up a fresh install of Ubuntu 10.10 x64. Second I got kerberos working with the following krb5.conf file: [libdefaults] ticket_lifetime = 24000 clock_skew = 300 default_realm = CUSTOMER.LOCAL [realms] CUSTOMER.LOCAL = { kdc = SB4.customer.local:88 admin_server = SB4.customer.local:464 default_domain = CUSTOMER.LOCAL } [domain_realm] .customer.local = CUSTOMER.LOCAL customer.local = CUSTOMER.LOCAL #[login] # krb4_convert = true # krb4_get_tickets = false I also added winbind to group, passwd and shadow in nsswitch.conf. Seemingly Kerberos works: root@lx:~# net ads testjoin Join is OK root@lx:~# wbinfo -a 'Administrator%MYSECRETPASSWORD' plaintext password authentication succeeded challenge/response password authentication succeeded wbinfo -u and wbinfo -g also spit out a list of users and a list of groups respectiveley. I noted that domain accounts did NOT include a domain and they are in german (as on the SBS 2003 that is the domain server). So I get a "Domänenbenutzer" in wbinfo -u's output not a "CUSTOMER+Domain User" or something similar. I'm not sure anymore what I did to the PAM configuration, but here is what I currently have: root@lx:/etc/pam.d# cat samba @include common-auth @include common-account @include common-session-noninteractive root@lx:/etc/pam.d# grep -ve '^#' common-auth auth [success=3 default=ignore] pam_krb5.so minimum_uid=1000 auth [success=2 default=ignore] pam_unix.so nullok_secure try_first_pass auth [success=1 default=ignore] pam_winbind.so krb5_auth krb5_ccache_type=FILE cached_login try_first_pass auth requisite pam_deny.so auth required pam_permit.so root@lx:/etc/pam.d# grep -ve '^#' common-account account [success=2 new_authtok_reqd=done default=ignore] pam_unix.so account [success=1 new_authtok_reqd=done default=ignore] pam_winbind.so account requisite pam_deny.so account required pam_permit.so account required pam_krb5.so minimum_uid=1000 root@lx:/etc/pam.d# grep -ve '^#' common-session-noninteractive session [default=1] pam_permit.so session requisite pam_deny.so session required pam_permit.so session optional pam_krb5.so minimum_uid=1000 session required pam_unix.so session optional pam_winbind.so At some point I joined the linux box into the AD domain. After (manually) creating a home directory on the linux box I can log in using the Adminstrator user with the password taken from AD. Now I run samba with the following setup: [global] netbios name = LX realm = CUSTOMER.LOCAL workgroup = CUSTOMER security = ADS encrypt passwords = yes password server = 192.168.20.244 #IP des Domain Controllers os level = 0 socket options = TCP_NODELAY SO_RCVBUF=16384 SO_SNDBUF=16384 idmap uid = 10000-20000 idmap gid = 10000-20000 winbind enum users = Yes winbind enum groups = Yes preferred master = no winbind separator = + dns proxy = no wins proxy = no # client NTLMv2 auth = Yes log level = 2 logfile = /var/log/samba/log.smbd.%U template homedir = /home/%U template shell = /bin/bash [export] path = /mnt/sdc1/export read only = No public = Yes Currently I don't care whether export is exported to everyone or just one user, I want to see somebody WRITING to that directory before I start fiddling with the authentication settings. (Who may access it). As mentioned, accessing the share from smbclient results in this NT_STATUS_MEDIA_WRITE_PROTECTED . Accessing it from windows shows ACLs that look correct (The user may write) - but it does not work, I can only read files not write. The directory to be exported looks like this: root@lx:/etc/pam.d# ls -ld /mnt/ drwxr-xr-x 5 root root 4096 2010-11-28 01:29 /mnt/ root@lx:/etc/pam.d# ls -ld /mnt/sdc1/ drwxr-xr-x 4 froh froh 4096 2010-11-28 01:32 /mnt/sdc1/ root@lx:/etc/pam.d# ls -ld /mnt/sdc1/export/ drwxrwxrwx+ 5 administrator domänen-admins 4096 2010-12-03 19:04 /mnt/sdc1/export/ root@lx:/etc/pam.d# getfacl /mnt/ getfacl: Entferne führende '/' von absoluten Pfadnamen # file: mnt/ # owner: root # group: root user::rwx group::r-x other::r-x root@lx:/etc/pam.d# getfacl /mnt/sdc1/ getfacl: Entferne führende '/' von absoluten Pfadnamen # file: mnt/sdc1/ # owner: froh # group: froh user::rwx group::r-x other::r-x root@lx:/etc/pam.d# getfacl /mnt/sdc1/export/ getfacl: Entferne führende '/' von absoluten Pfadnamen # file: mnt/sdc1/export/ # owner: administrator # group: domänen-admins user::rwx group::rwx group:domänen-admins:rwx mask::rwx other::rwx default:user::rwx default:group::rwx default:group:domänen-admins:rwx default:mask::rwx default:other::rwx My, oh my what am I overlooking? What am I to blind to see?

  Read the article

• can't connect 2 subnets through RRAS 2008 r2

  - by mcdwight6

  I'm working on a project for a networking class. In VMWare Workstation, I have to set up a 2008 r2 server with DHCP reservations for 2 clients on separate subnets and have them ping each other. Here is the output of the route print command: =========================================================================== Interface List 13 ...00 50 56 2a e7 11 ...... Intel(R) PRO/1000 MT Network Connection #3 10 ...00 0c 29 66 88 dd ...... Intel(R) PRO/1000 MT Network Connection 1 ........................... Software Loopback Interface 1 24 ...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 11 ...02 00 54 55 4e 01 ...... Teredo Tunneling Pseudo-Interface 14 ...00 00 00 00 00 00 00 e0 6TO4 Adapter 16 ...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 17 ...00 00 00 00 00 00 00 e0 isatap.{5B8FB196-616F-4168-A020-03E63A309CEC} =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 On-link 10.0.0.2 266 0.0.0.0 0.0.0.0 On-link 223.6.6.2 266 10.0.0.0 255.0.0.0 On-link 10.0.0.2 266 10.0.0.2 255.255.255.255 On-link 10.0.0.2 266 10.255.255.255 255.255.255.255 On-link 10.0.0.2 266 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 128.6.0.0 255.255.0.0 On-link 10.0.0.2 11 128.6.255.255 255.255.255.255 On-link 10.0.0.2 266 223.6.6.0 255.255.255.0 On-link 10.0.0.2 11 223.6.6.0 255.255.255.0 On-link 223.6.6.2 266 223.6.6.2 255.255.255.255 On-link 223.6.6.2 266 223.6.6.255 255.255.255.255 On-link 10.0.0.2 266 223.6.6.255 255.255.255.255 On-link 223.6.6.2 266 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 10.0.0.2 266 224.0.0.0 240.0.0.0 On-link 223.6.6.2 266 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 10.0.0.2 266 255.255.255.255 255.255.255.255 On-link 223.6.6.2 266 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 0.0.0.0 0.0.0.0 10.0.0.2 Default 0.0.0.0 0.0.0.0 128.6.0.2 Default 0.0.0.0 0.0.0.0 223.6.6.2 Default 128.6.0.0 255.255.0.0 10.0.0.2 1 223.6.6.0 255.255.255.0 10.0.0.2 1 =========================================================================== IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 1 306 ::1/128 On-link 14 1010 2002::/16 On-link 14 266 2002:8006:2::8006:2/128 On-link 1 306 ff00::/8 On-link =========================================================================== Persistent Routes: None My problem is that although I have set up both dynamic and persistent static routes in my r2 server, neither of the clients can ping even the NIC outside its own subnet. For example Client A can ping the NIC at 10.0.0.2 and vice-versa, but it gets a general transmit failure when it tries to ping the card at 223.6.6.2, let alone trying to ping the other client. I have completely disabled the firewalls on all machines and anything else I could think of, without success. What am I missing? Edit: Since posting this, I also noticed that the default gateways on my 2 NICs keep getting zeroed out. Does anyone know a fix for this?

  Read the article

• /phpTest/zologize/axa.php? Another botnet?

  - by M132

  Starring at the log made me think, what is /phpTest/zologize/axa.php and why are bots looking for it? Previously, I had lots of /HNAP1/ requests. Requesting /HNAP1/ from IPs from log revealed, that all of them were sent by Linksys routers. 3 months later, these requests turned out to be generated by a router worm called TheMoon. But requesting /phpTest/zologize/axa.php from these servers returns a 404 error. How these servers got infected, and how can I protect mine from this? 124.11.224.69 - - [02/Feb/2014:00:37:16 +0100] "GET /phpTest/zologize/axa.php HTTP/1.1" 404 168 "-" "-" 140.113.238.121 - - [21/Feb/2014:01:24:32 +0100] "GET /phpTest/zologize/axa.php HTTP/1.1" 404 168 "-" "-" 77.121.132.79 - - [22/Feb/2014:00:03:56 +0100] "GET /phpTest/zologize/axa.php HTTP/1.1" 404 168 "-" "-" 142.4.201.210 - - [24/Feb/2014:21:54:33 +0100] "GET /phpTest/zologize/axa.php HTTP/1.1" 404 168 "-" "-" 212.83.168.39 - - [24/Feb/2014:23:16:00 +0100] "GET /phpTest/zologize/axa.php HTTP/1.1" 404 168 "-" "-" 87.117.229.210 - - [26/Feb/2014:06:34:58 +0100] "GET /phpTest/zologize/axa.php HTTP/1.1" 404 162 "-" "-" 78.100.82.99 - - [26/Feb/2014:08:25:48 +0100] "GET /phpTest/zologize/axa.php HTTP/1.1" 404 162 "-" "-" 198.50.205.219 - - [26/Feb/2014:09:59:11 +0100] "GET /phpTest/zologize/axa.php HTTP/1.1" 404 162 "-" "-" 210.60.142.107 - - [27/Feb/2014:00:12:12 +0100] "GET /phpTest/zologize/axa.php HTTP/1.1" 404 162 "-" "-" 101.109.4.73 - - [27/Feb/2014:08:50:46 +0100] "GET /phpTest/zologize/axa.php HTTP/1.1" 404 162 "-" "-" 61.91.128.158 - - [27/Feb/2014:08:59:15 +0100] "GET /phpTest/zologize/axa.php HTTP/1.1" 404 162 "-" "-" 201.188.41.175 - - [27/Feb/2014:11:25:42 +0100] "GET /phpTest/zologize/axa.php HTTP/1.1" 404 162 "-" "-" 220.133.137.2 - - [27/Feb/2014:12:12:46 +0100] "GET /phpTest/zologize/axa.php HTTP/1.1" 404 162 "-" "-" 203.156.104.88 - - [28/Feb/2014:18:11:49 +0100] "GET /phpTest/zologize/axa.php HTTP/1.1" 404 162 "-" "-" 61.19.52.58 - - [28/Feb/2014:22:02:56 +0100] "GET /phpTest/zologize/axa.php HTTP/1.1" 404 162 "-" "-" 84.2.92.40 - - [28/Feb/2014:23:04:17 +0100] "GET /phpTest/zologize/axa.php HTTP/1.1" 404 162 "-" "-" 58.64.205.11 - - [01/Mar/2014:06:08:33 +0100] "GET /phpTest/zologize/axa.php HTTP/1.1" 200 21 "-" "-" 113.61.200.151 - - [01/Mar/2014:18:25:25 +0100] "GET /phpTest/zologize/axa.php HTTP/1.1" 200 21 "-" "-" 178.33.219.12 - - [03/Mar/2014:14:41:48 +0100] "GET /phpTest/zologize/axa.php HTTP/1.1" 200 21 "-" "-" 74.63.220.132 - - [04/Mar/2014:01:16:44 +0100] "GET /phpTest/zologize/axa.php HTTP/1.1" 200 21 "-" "-" 187.141.230.106 - - [04/Mar/2014:15:39:26 +0100] "GET /phpTest/zologize/axa.php HTTP/1.1" 200 21 "-" "-" 103.22.181.146 - - [09/May/2014:17:16:56 +0200] "GET /phpTest/zologize/axa.php HTTP/1.1" 502 166 "-" "-" 176.31.200.14 - - [10/May/2014:19:52:24 +0200] "GET /phpTest/zologize/axa.php HTTP/1.1" 200 68 "-" "-" 124.120.92.70 - - [12/May/2014:16:19:40 +0200] "GET /phpTest/zologize/axa.php HTTP/1.1" 200 68 "-" "-" 219.85.198.142 - - [15/May/2014:19:21:22 +0200] "GET /phpTest/zologize/axa.php HTTP/1.1" 200 37 "-" "-" 80.84.53.226 - - [23/May/2014:08:58:25 +0200] "GET /phpTest/zologize/axa.php HTTP/1.1" 200 37 "-" "-" 87.213.11.165 - - [25/May/2014:06:20:27 +0200] "GET /phpTest/zologize/axa.php HTTP/1.1" 200 37 "-" "-" 122.116.220.106 - - [25/May/2014:07:10:21 +0200] "GET /phpTest/zologize/axa.php HTTP/1.1" 200 37 "-" "-" 58.8.128.30 - - [29/May/2014:02:43:49 +0200] "GET /phpTest/zologize/axa.php HTTP/1.1" 200 37 "-" "-" 142.4.197.135 - - [29/May/2014:11:36:45 +0200] "GET /phpTest/zologize/axa.php HTTP/1.1" 200 37 "-" "-" 178.32.243.65 - - [30/May/2014:01:59:53 +0200] "GET /phpTest/zologize/axa.php HTTP/1.1" 200 37 "-" "-" 58.8.164.221 - - [30/May/2014:14:04:16 +0200] "GET /phpTest/zologize/axa.php HTTP/1.1" 200 37 "-" "-" 140.127.182.15 - - [01/Jun/2014:14:45:40 +0200] "GET /phpTest/zologize/axa.php HTTP/1.1" 200 37 "-" "-" 218.166.43.21 - - [01/Jun/2014:16:07:52 +0200] "GET /phpTest/zologize/axa.php HTTP/1.1" 200 37 "-" "-" 178.32.188.140 - - [01/Jun/2014:19:11:46 +0200] "GET /phpTest/zologize/axa.php HTTP/1.1" 200 37 "-" "-" 94.23.211.173 - - [05/Jun/2014:00:52:52 +0200] "GET /phpTest/zologize/axa.php HTTP/1.1" 200 37 "-" "-" 120.117.105.201 - - [05/Jun/2014:04:39:39 +0200] "GET /phpTest/zologize/axa.php HTTP/1.1" 200 37 "-" "-" 187.172.27.146 - - [05/Jun/2014:10:20:22 +0200] "GET /phpTest/zologize/axa.php HTTP/1.1" 200 37 "-" "-" 203.195.219.91 - - [05/Jun/2014:10:53:42 +0200] "GET /phpTest/zologize/axa.php HTTP/1.1" 200 37 "-" "-"

  Read the article

• Identifying the cause of my DNS failure (domain not propagating)

  - by thejartender

  I have set up a DNS server with the help of two helpful tutorials: http://linuxconfig.org/linux-dns-server-bind-configuration http://ulyssesonline.com/2007/11/07/how-to-setup-a-dns-server-in-ubuntu/ I am using: Ubuntu Bind9 and had issues I tried negating on my own thanks to a question I posted here earlier that pointed out my mistake of using rfc 1918 addresses in my previous SOA record: $TTL 3D @ IN SOA ns.thejarbar.org. email. ( 13112012 28800 3600 604800 38400 ); thejarbar.org. IN A 10.0.0.42 @ IN NS ns.thejarbar,org. yuccalaptop IN A 10.0.0.19 ns IN A 10.0.0.42 gw IN A 10.0.0.138 www IN CNAME thejarbar.org. $TTL 600 0.0.10.in-addr.arpa. IN SOA ns.thejarbar.org. email. ( 13112012 28800 3600 604800 38400 ); 0.0.10.in-addr.arpa. IN NS ns.thejarbar.org. 42 IN PTR thejarbar.org. 19 IN PTR yuccalaptop.thejarbar.org. 138 IN PTR gw.thejarbar.org. I read the ranges that are used under rfc 1918 and modified my routers resource pool to assign LAN devices IP(s) within the 30.0.0.0 range and now modified my SOA to: $TTL 600 @ IN SOA ns.thejarbar.org. email. ( 13112012 28800 3600 604800 38400 ); thejarbar.org. IN A 30.0.0.42 @ IN NS ns.thejarbar,org. yuccalaptop IN A 10.0.0.19 ns IN A 30.0.0.42 gw IN A 30.0.0.138 www IN CNAME thejarbar.org. $TTL600 0.0.10.in-addr.arpa. IN SOA ns.thejarbar.org. email. ( 13112012 28800 3600 604800 38400 ); 0.0.30.in-addr.arpa. IN NS ns.thejarbar.org. 42 IN PTR thejarbar.org. 19 IN PTR yuccalaptop.thejarbar.org. 138 IN PTR gw.thejarbar.org. I can ping my nameserverver ns.thejarbar.organd it gives me the correct isp IP address, but my domain never seems to propagate to my nameserver. I have searched for a concise tutorial that covers setting up a DNS with a nameserver that hosts (my) or the site. I am fully aware that this is not recommended and am using this for my learning purposes. Getting to the question, due to the lack of information in tutorials I looked at (nothing about rfc 1918 and no example of swapping these with ISP IP) is my router modification going to help me as it does not seem to be. I have also tried as recommended using my ISP IP instead of the values I posted. My site never propagated to my nameserver. What could be causing this? I have run dig thejarbar.org @88.89.190.171 and get an authorative response. Can anyone assist me with the final steps I may be missing here?

  Read the article

• Mysqld not starting due to apparent db corruption

  - by pitosalas

  I am very new at admining mysql, and bad for me, something caused the db to get clobbered. There are many error messages in the log that I am not sure how to safely proceed. Can you give some tips? Here's the log: 110107 15:07:15 mysqld started 110107 15:07:15 InnoDB: Database was not shut down normally! InnoDB: Starting crash recovery. InnoDB: Reading tablespace information from the .ibd files... InnoDB: Restoring possible half-written data pages from the doublewrite InnoDB: buffer... 110107 15:07:15 InnoDB: Starting log scan based on checkpoint at InnoDB: log sequence number 35 515914826. InnoDB: Doing recovery: scanned up to log sequence number 35 515915839 InnoDB: 1 transaction(s) which must be rolled back or cleaned up InnoDB: in total 1 row operations to undo InnoDB: Trx id counter is 0 1697553664 110107 15:07:15 InnoDB: Starting an apply batch of log records to the database... InnoDB: Progress in percents: 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 InnoDB: Apply batch completed InnoDB: Starting rollback of uncommitted transactions InnoDB: Rolling back trx with id 0 1697553198, 1 rows to undoInnoDB: Error: trying to access page number 3522914176 in space 0, InnoDB: space name ./ibdata1, InnoDB: which is outside the tablespace bounds. InnoDB: Byte offset 0, len 16384, i/o type 10 110107 15:07:15InnoDB: Assertion failure in thread 3086403264 in file fil0fil.c line 3922 InnoDB: We intentionally generate a memory trap. InnoDB: Submit a detailed bug report to http://bugs.mysql.com. InnoDB: If you get repeated assertion failures or crashes, even InnoDB: immediately after the mysqld startup, there may be InnoDB: corruption in the InnoDB tablespace. Please refer to InnoDB: http://dev.mysql.com/doc/mysql/en/Forcing_recovery.html InnoDB: about forcing recovery. mysqld got signal 11; This could be because you hit a bug. It is also possible that this binary or one of the libraries it was linked against is corrupt, improperly built, or misconfigured. This error can also be caused by malfunctioning hardware. We will try our best to scrape up some info that will hopefully help diagnose the problem, but since we have already crashed, something is definitely wrong and this may fail. key_buffer_size=0 read_buffer_size=131072 max_used_connections=0 max_connections=100 threads_connected=0 It is possible that mysqld could use up to key_buffer_size + (read_buffer_size + sort_buffer_size)*max_connections = 217599 K bytes of memory Hope that's ok; if not, decrease some variables in the equation. thd=(nil) Attempting backtrace. You can use the following information to find out where mysqld died. If you see no messages after this, something went terribly wrong... Cannot determine thread, fp=0xbffc55ac, backtrace may not be correct. Stack range sanity check OK, backtrace follows: 0x8139eec 0x83721d5 0x833d897 0x833db71 0x832aa38 0x835f025 0x835f7a3 0x830a77e 0x8326b57 0x831c825 0x8317b8d 0x82a9e66 0x8315732 0x834fc9a 0x828d7c3 0x81c29dd 0x81b5620 0x813d9fe 0x40fdf3 0x80d5ff1 New value of fp=(nil) failed sanity check, terminating stack trace! Please read http://dev.mysql.com/doc/mysql/en/Using_stack_trace.html and follow instructions on how to resolve the stack trace. Resolved stack trace is much more helpful in diagnosing the problem, so please do resolve it The manual page at http://www.mysql.com/doc/en/Crashing.html contains information that should help you find out what is causing the crash. 110107 15:07:15 mysqld ended

  Read the article

• Updating a SharePoint master page via a solution (WSP)

  - by Kelly Jones

  In my last blog post, I wrote how to deploy a SharePoint theme using Features and a solution package.  As promised in that post, here is how to update an already deployed master page. There are several ways to update a master page in SharePoint.  You could upload a new version to the master page gallery, or you could upload a new master page to the gallery, and then set the site to use this new page.  Manually uploading your master page to the master page gallery might be the best option, depending on your environment.  For my client, I did these steps in code, which is what they preferred. (Image courtesy of: http://www.joiningdots.net/blog/2007/08/sharepoint-and-quick-launch.html ) Before you decide which method you need to use, take a look at your existing pages.  Are they using the SharePoint dynamic token or the static token for the master page reference?  The wha, huh? SO, there are four ways to tell an .aspx page hosted in SharePoint which master page it should use: “~masterurl/default.master” – tells the page to use the default.master property of the site “~masterurl/custom.master” – tells the page to use the custom.master property of the site “~site/default.master” – tells the page to use the file named “default.master” in the site’s master page gallery “~sitecollection/default.master” – tells the page to use the file named “default.master” in the site collection’s master page gallery For more information about these tokens, take a look at this article on MSDN. Once you determine which token your existing pages are pointed to, then you know which file you need to update.  So, if the ~masterurl tokens are used, then you upload a new master page, either replacing the existing one or adding another one to the gallery.  If you’ve uploaded a new file with a new name, you’ll just need to set it as the master page either through the UI (MOSS only) or through code (MOSS or WSS Feature receiver code – or using SharePoint Designer). If the ~site or ~sitecollection tokens were used, then you’re limited to either replacing the existing master page, or editing all of your existing pages to point to another master page.  In most cases, it probably makes sense to just replace the master page. For my project, I’m working with WSS and the existing pages are set to the ~sitecollection token.  Based on this, I decided to just upload a new version of the existing master page (and not modify the dozens of existing pages). Also, since my client prefers Features and solutions, I created a master page Feature and a corresponding Feature Receiver.  For information on creating the elements and feature files, check out this post: http://sharepointmagazine.net/technical/development/deploying-the-master-page . This works fine, unless you are overwriting an existing master page, which was my case.  You’ll run into errors because the master page file needs to be checked out, replaced, and then checked in.  I wrote code in my Feature Activated event handler to accomplish these steps. Here are the steps necessary in code: Get the file name from the elements file of the Feature Check out the file from the master page gallery Upload the file to the master page gallery Check in the file to the master page gallery Here’s the code in my Feature Receiver: 1: public override void FeatureActivated(SPFeatureReceiverProperties properties) 2: { 3: try 4: { 5:   6: SPElementDefinitionCollection col = properties.Definition.GetElementDefinitions(System.Globalization.CultureInfo.CurrentCulture); 7:   8: using (SPWeb curweb = GetCurWeb(properties)) 9: { 10: foreach (SPElementDefinition ele in col) 11: { 12: if (string.Compare(ele.ElementType, "Module", true) == 0) 13: { 14: // <Module Name="DefaultMasterPage" List="116" Url="_catalogs/masterpage" RootWebOnly="FALSE"> 15: // <File Url="myMaster.master" Type="GhostableInLibrary" IgnoreIfAlreadyExists="TRUE" 16: // Path="MasterPages/myMaster.master" /> 17: // </Module> 18: string Url = ele.XmlDefinition.Attributes["Url"].Value; 19: foreach (System.Xml.XmlNode file in ele.XmlDefinition.ChildNodes) 20: { 21: string Url2 = file.Attributes["Url"].Value; 22: string Path = file.Attributes["Path"].Value; 23: string fileType = file.Attributes["Type"].Value; 24:   25: if (string.Compare(fileType, "GhostableInLibrary", true) == 0) 26: { 27: //Check out file in document library 28: SPFile existingFile = curweb.GetFile(Url + "/" + Url2); 29:   30: if (existingFile != null) 31: { 32: if (existingFile.CheckOutStatus != SPFile.SPCheckOutStatus.None) 33: { 34: throw new Exception("The master page file is already checked out. Please make sure the master page file is checked in, before activating this feature."); 35: } 36: else 37: { 38: existingFile.CheckOut(); 39: existingFile.Update(); 40: } 41: } 42:   43: //Upload file to document library 44: string filePath = System.IO.Path.Combine(properties.Definition.RootDirectory, Path); 45: string fileName = System.IO.Path.GetFileName(filePath); 46: char slash = Convert.ToChar("/"); 47: string[] folders = existingFile.ParentFolder.Url.Split(slash); 48:   49: if (folders.Length > 2) 50: { 51: Logger.logMessage("More than two folders were detected in the library path for the master page. Only two are supported.", 52: Logger.LogEntryType.Information); //custom logging component 53: } 54:   55: SPFolder myLibrary = curweb.Folders[folders[0]].SubFolders[folders[1]]; 56:   57: FileStream fs = File.OpenRead(filePath); 58:   59: SPFile newFile = myLibrary.Files.Add(fileName, fs, true); 60:   61: myLibrary.Update(); 62: newFile.CheckIn("Updated by Feature", SPCheckinType.MajorCheckIn); 63: newFile.Update(); 64: } 65: } 66: } 67: } 68: } 69: } 70: catch (Exception ex) 71: { 72: string msg = "Error occurred during feature activation"; 73: Logger.logException(ex, msg, ""); 74: } 75:   76: } 77:   78: /// <summary> 79: /// Using a Feature's properties, get a reference to the Current Web 80: /// </summary> 81: /// <param name="properties"></param> 82: public SPWeb GetCurWeb(SPFeatureReceiverProperties properties) 83: { 84: SPWeb curweb; 85:   86: //Check if the parent of the web is a site or a web 87: if (properties != null && properties.Feature.Parent.GetType().ToString() == "Microsoft.SharePoint.SPWeb") 88: { 89:   90: //Get web from parent 91: curweb = (SPWeb)properties.Feature.Parent; 92: 93: } 94: else 95: { 96: //Get web from Site 97: using (SPSite cursite = (SPSite)properties.Feature.Parent) 98: { 99: curweb = (SPWeb)cursite.OpenWeb(); 100: } 101: } 102:   103: return curweb; 104: } This did the trick.  It allowed me to update my existing master page, through an easily repeatable process (which is great when you are working with more than one environment and what to do things like TEST it!).  I did run into what I would classify as a strange issue with one of my subsites, but that’s the topic for another blog post.

  Read the article

• European Interoperability Framework - a new beginning?

  - by trond-arne.undheim

  The most controversial document in the history of the European Commission's IT policy is out. EIF is here, wrapped in the Communication "Towards interoperability for European public services", and including the new feature European Interoperability Strategy (EIS), arguably a higher strategic take on the same topic. Leaving EIS aside for a moment, the EIF controversy has been around IPR, defining open standards and about the proper terminology around standardization deliverables. Today, as the document finally emerges, what is the verdict? First of all, to be fair to those among you who do not spend your lives in the intricate labyrinths of Commission IT policy documents on interoperability, let's define what we are talking about. According to the Communication: "An interoperability framework is an agreed approach to interoperability for organisations that want to collaborate to provide joint delivery of public services. Within its scope of applicability, it specifies common elements such as vocabulary, concepts, principles, policies, guidelines, recommendations, standards, specifications and practices." The Good - EIF reconfirms that "The Digital Agenda can only take off if interoperability based on standards and open platforms is ensured" and also confirms that "The positive effect of open specifications is also demonstrated by the Internet ecosystem." - EIF takes a productive and pragmatic stance on openness: "In the context of the EIF, openness is the willingness of persons, organisations or other members of a community of interest to share knowledge and stimulate debate within that community, the ultimate goal being to advance knowledge and the use of this knowledge to solve problems" (p.11). "If the openness principle is applied in full: - All stakeholders have the same possibility of contributing to the development of the specification and public review is part of the decision-making process; - The specification is available for everybody to study; - Intellectual property rights related to the specification are licensed on FRAND terms or on a royalty-free basis in a way that allows implementation in both proprietary and open source software" (p. 26). - EIF is a formal Commission document. The former EIF 1.0 was a semi-formal deliverable from the PEGSCO, a working group of Member State representatives. - EIF tackles interoperability head-on and takes a clear stance: "Recommendation 22. When establishing European public services, public administrations should prefer open specifications, taking due account of the coverage of functional needs, maturity and market support." - The Commission will continue to support the National Interoperability Framework Observatory (NIFO), reconfirming the importance of coordinating such approaches across borders. - The Commission will align its internal interoperability strategy with the EIS through the eCommission initiative. - One cannot stress the importance of using open standards enough, whether in the context of open source or non-open source software. The EIF seems to have picked up on this fact: What does the EIF says about the relation between open specifications and open source software? The EIF introduces, as one of the characteristics of an open specification, the requirement that IPRs related to the specification have to be licensed on FRAND terms or on a royalty-free basis in a way that allows implementation in both proprietary and open source software. In this way, companies working under various business models can compete on an equal footing when providing solutions to public administrations while administrations that implement the standard in their own software (software that they own) can share such software with others under an open source licence if they so decide. - EIF is now among the center pieces of the Digital Agenda (even though this demands extensive inter-agency coordination in the Commission): "The EIS and the EIF will be maintained under the ISA Programme and kept in line with the results of other relevant Digital Agenda actions on interoperability and standards such as the ones on the reform of rules on implementation of ICT standards in Europe to allow use of certain ICT fora and consortia standards, on issuing guidelines on essential intellectual property rights and licensing conditions in standard-setting, including for ex-ante disclosure, and on providing guidance on the link between ICT standardisation and public procurement to help public authorities to use standards to promote efficiency and reduce lock-in.(Communication, p.7)" All in all, quite a few good things have happened to the document in the two years it has been on the shelf or was being re-written, depending on your perspective, in any case, awaiting the storms to calm. The Bad - While a certain pragmatism is required, and governments cannot migrate to full openness overnight, EIF gives a bit too much room for governments not to apply the openness principle in full. Plenty of reasons are given, which should maybe have been put as challenges to be overcome: "However, public administrations may decide to use less open specifications, if open specifications do not exist or do not meet functional interoperability needs. In all cases, specifications should be mature and sufficiently supported by the market, except if used in the context of creating innovative solutions". - EIF does not use the internationally established terminology: open standards. Rather, the EIF introduces the notion of "formalised specification". How do "formalised specifications" relate to "standards"? According to the FAQ provided: The word "standard" has a specific meaning in Europe as defined by Directive 98/34/EC. Only technical specifications approved by a recognised standardisation body can be called a standard. Many ICT systems rely on the use of specifications developed by other organisations such as a forum or consortium. The EIF introduces the notion of "formalised specification", which is either a standard pursuant to Directive 98/34/EC or a specification established by ICT fora and consortia. The term "open specification" used in the EIF, on the one hand, avoids terminological confusion with the Directive and, on the other, states the main features that comply with the basic principle of openness laid down in the EIF for European Public Services. Well, this may be somewhat true, but in reality, Europe is 30 year behind in terminology. Unless the European Standardization Reform gets completed in the next few months, most Member States will likely conclude that they will go on referencing and using standards beyond those created by the three European endorsed monopolists of standardization, CEN, CENELEC and ETSI. Who can afford to begin following the strict Brussels rules for what they can call open standards when, in reality, standards stemming from global standardization organizations, so-called fora/consortia, dominate in the IT industry. What exactly is EIF saying? Does it encourage Member States to go on using non-ESO standards as long as they call it something else? I guess I am all for it, although it is a bit cumbersome, no? Why was there so much interest around the EIF? The FAQ attempts to explain: Some Member States have begun to adopt policies to achieve interoperability for their public services. These actions have had a significant impact on the ecosystem built around the provision of such services, e.g. providers of ICT goods and services, standardisation bodies, industry fora and consortia, etc... The Commission identified a clear need for action at European level to ensure that actions by individual Member States would not create new electronic barriers that would hinder the development of interoperable European public services. As a result, all stakeholders involved in the delivery of electronic public services in Europe have expressed their opinions on how to increase interoperability for public services provided by the different public administrations in Europe. Well, it does not take two years to read 50 consultation documents, and the EU Standardization Reform is not yet completed, so, more pragmatically, you finally had to release the document. Ok, let's leave some of that aside because the document is out and some people are happy (and others definitely not). The Verdict Considering the controversy, the delays, the lobbying, and the interests at stake both in the EU, in Member States and among vendors large and small, this document is pretty impressive. As with a good wine that has not yet come to full maturity, let's say that it seems to be coming in in the 85-88/100 range, but only a more fine-grained analysis, enjoyment in good company, and ultimately, implementation, will tell. The European Commission has today adopted a significant interoperability initiative to encourage public administrations across the EU to maximise the social and economic potential of information and communication technologies. Today, we should rally around this achievement. Tomorrow, let's sit down and figure out what it means for the future.

  Read the article

• CodePlex Daily Summary for Thursday, June 17, 2010

  CodePlex Daily Summary for Thursday, June 17, 2010New ProjectsAstalanumerator: A JavaScript based recursive DOM/JS object inspector. Uses a simple tree menu to enumerate all properties of a object.BDD Log Converter: A simple .NET class and console application that will convert BDD logs (MDT) into XML format.CastleInvestProj: Castle Investigating project Easy Callback: This library facilitates the use of multiple asynchronous calls on the same page, and asynchronous calls from a user control also have a clean cod...Easy Wings: Small webApp to manage aircraft booking in flying club. French only for the moment.EPiServer Template Foundation: EPiServer Template Foundation builds on top of Page Type Builder to provide a framework for common site features such as basic page type properties...guidebook: a project to plan your road trip.Look into documents for e-discovery: Search, browse, tag, annotate documents such as MS Word, PDF, e-mail, etc. Good for legal professionals do e-discovery. One Bus Away for Windows Phone: A Windows Phone 7 application written in Silverlight for the OneBusAway (www.onebusaway.org) website. Allows mobile users to search for public tra...OneBusAway for Windows Phone 7: OneBusAway is a service with transit information for the Seattle, WA region. We are creating a mobile application for Windows Phone 7 utilizing th...PoFabLab - Poetry Generation Library and Editor in .NET: PoFabLab is an open source library and word processor designed for digital poets. The library can scan lines, perform Markov analysis, filter text...Project Axure: More details coming soon.Чат кутежа 2.0: ИРЦ чат специально для форума ЕНЕ简易代码生成器: 初次使用CodePlex，这只是一个测试项目。打算用WPF做一个简单的代码生成器，兼具SQL Server Client功能。使用.Net 4.0, C#开发。运营工作系统: TRAS(Team resource assist system) is a toolkit that help the studio to manage and distribute the daily work, like publish the news, GM broadcast a...New ReleasesAmuse - A New MU* Client For Windows: 2010 June: Important Notice to TestersPlease uninstall any previous versions of Amuse prior to this one before installing. Changes and InformationFirst relea...ASP.NET Generic Data Source Control: V1.0: GenericDataSource - Version 1.0Binary This is the first official binary release of the GenericDataSource for ASP.NET - stable and ready for product...Astalanumerator: Astalanumerator 0.7: I wanted to map all properties in javascript and inspect them regardless if they were objects or not. IE doesn’t support for(i in..) for native pro...BDD Log Converter: BDD Log Converter 0.1.0: First release (0.1.0).DVD Swarm: 0.8.10.616: Major update with improvements to encoding speed.Easy Callback: Easy Callback 1.0.0.0: Easy Callback library 1.0.0.0Facebook Connect Authentication for ASP.NET: Facebook Connect Authentication for ASP.NET - v1.0: Now supporting Facebook's new Open Graph API JavaScript SDK, this release of FBConnectAuth also adds support for running in partially trusted envir...FlickrNet API Library: 3.0 Beta 3: Another small Beta. Changed parsing code so exceptions aren't raised when new attributes are added by Flickr. This affects searches where you are ...Infragistics Analytics Framework: Infragistics Analytics Framework 10.2: An updated version of Infragistics Analytics Framework, which utilizes the newest version (v.1.4.4) of MSAF as well as the newest release (v.10.2) ...NUnit Add-in for Growl Notifications: NUnit Add-in for Growl Notifications 1.0 build 1: Version 1.0 build 1:[change] Test run failure notification now disappears automaticallyOpen Source PLM Activities: 3dxml player integration for Aras Innovator: This is just a simple html file you need to add to your Aras Innovator install directory. It loads the 3Dxml player for your 3dxml files. Tested o...patterns & practices - Windows Azure Guidance: WAAG - Part 2 - Drop 1: First code and docs drop for Part 2 of the Windows Azure Architecture Guide Part 1 of the Guide is released here. Highlights of this release are:...Phalanger - The PHP Language Compiler for the .NET Framework: 2.0 (June 2010): Installer of the latest binaries of Phalanger 2.0 (June 2010) and its integration into Visual Studio 2008 SP1. * Improved compatibility with P...RIA Services Essentials: Book Club Application (June 16, 2010): Added some XAML to hide/show link to BookShelf page based on whether the user is logged in or not. Updated IsBookOwner authorization rule implement...secs4net: Relase 1.01: version 1.01 releasesELedit: sELedit v1.1c: Added: Tool for exporting NPC/Mob database file that is used by sNPCeditSharePoint Ad Rotator: SPAdRotator 2.0 Beta 2: Added: Open tool pane link to default Web Part text Made all images except the first hidden by default, so the Web Part will degrade gracefully w...sMAPtool: sMAPtool v0.7f (without Maps): Added: 3rd party magnifier softwaresNPCedit: sNPCedit v0.9c: Added: npc/mob names and corresponding datbaseSolidWorks Addin Development: GenericAddinFrameworkR1-06.17.2010: .sTASKedit: sTASKedit v0.8: Important BugFix: there was an mistake in the structure, team-member block and get-items block was swapped internally. Tasks that contains both blo...stefvanhooijdonk.com: UnitTesting-SP2010-TFS2010: Files for my post on TFS2010 and NUnit testing with SP2010 projects. see the post here: http://wp.me/pMnlQ-88 The XSLT here is from http://nunit4t...Telerik CAB Enabling Kit for RadControls for WinForms: TCEK 2010.1.10.504: What's new in v2010.1.0610 (Beta): RadDocking component has been replaced with the latest RadDock control Requirements: Visual Studio 2005+ Tele...TFS Buddy: TFS Buddy 1.2: Fixes a problem with notificationsThales Simulator Library: Version 0.9: The Thales Simulator Library is an implementation of a software emulation of the Thales (formerly Zaxus & Racal) Hardware Security Module cryptogra...Triton Application Framework: Tools - Code Generator - Build 1.0: This is the first release of the Generator. This is buggy but works.VCC: Latest build, v2.1.30616.0: Automatic drop of latest buildXsltDb - DotNetNuke Module Builder: 01.01.27: Code completion for XsltDb, HTML and XSL stuff!! Full screen editing Some bugs are still in EditArea component and object lists in code completi...Чат кутежа 2.0: 0.9a build 2 версия: вторая сборка первой альфа-версии ирц-клиента.Most Popular ProjectsWBFS ManagerRawrAJAX Control ToolkitMicrosoft SQL Server Product Samples: DatabaseSilverlight ToolkitWindows Presentation Foundation (WPF)patterns & practices – Enterprise LibraryPHPExcelMicrosoft SQL Server Community & SamplesASP.NETMost Active ProjectsdotSpatialpatterns & practices: Enterprise Library Contribpatterns & practices – Enterprise LibraryBlogEngine.NETLightweight Fluent WorkflowRhyduino - Arduino and Managed CodeSunlit World SchemeNB_Store - Free DotNetNuke Ecommerce Catalog ModuleSolidWorks Addin DevelopmentN2 CMS

  Read the article

• J2EE Applications, SPARC T4, Solaris Containers, and Resource Pools

  - by user12620111

  I've obtained a substantial performance improvement on a SPARC T4-2 Server running a J2EE Application Server Cluster by deploying the cluster members into Oracle Solaris Containers and binding those containers to cores of the SPARC T4 Processor. This is not a surprising result, in fact, it is consistent with other results that are available on the Internet. See the "references", below, for some examples. Nonetheless, here is a summary of my configuration and results. (1.0) Before deploying a J2EE Application Server Cluster into a virtualized environment, many decisions need to be made. I'm not claiming that all of the decisions that I have a made will work well for every environment. In fact, I'm not even claiming that all of the decisions are the best possible for my environment. I'm only claiming that of the small sample of configurations that I've tested, this is the one that is working best for me. Here are some of the decisions that needed to be made: (1.1) Which virtualization option? There are several virtualization options and isolation levels that are available. Options include: Hard partitions:  Dynamic Domains on Sun SPARC Enterprise M-Series Servers Hypervisor based virtualization such as Oracle VM Server for SPARC (LDOMs) on SPARC T-Series Servers OS Virtualization using Oracle Solaris Containers Resource management tools in the Oracle Solaris OS to control the amount of resources an application receives, such as CPU cycles, physical memory, and network bandwidth. Oracle Solaris Containers provide the right level of isolation and flexibility for my environment. To borrow some words from my friends in marketing, "The SPARC T4 processor leverages the unique, no-cost virtualization capabilities of Oracle Solaris Zones"  (1.2) How to associate Oracle Solaris Containers with resources? There are several options available to associate containers with resources, including (a) resource pool association (b) dedicated-cpu resources and (c) capped-cpu resources. I chose to create resource pools and associate them with the containers because I wanted explicit control over the cores and virtual processors.  (1.3) Cluster Topology? Is it best to deploy (a) multiple application servers on one node, (b) one application server on multiple nodes, or (c) multiple application servers on multiple nodes? After a few quick tests, it appears that one application server per Oracle Solaris Container is a good solution. (1.4) Number of cluster members to deploy? I chose to deploy four big 64-bit application servers. I would like go back a test many 32-bit application servers, but that is left for another day. (2.0) Configuration tested. (2.1) I was using a SPARC T4-2 Server which has 2 CPU and 128 virtual processors. To understand the physical layout of the hardware on Solaris 10, I used the OpenSolaris psrinfo perl script available at http://hub.opensolaris.org/bin/download/Community+Group+performance/files/psrinfo.pl: test# ./psrinfo.pl -pv The physical processor has 8 cores and 64 virtual processors (0-63) The core has 8 virtual processors (0-7)   The core has 8 virtual processors (8-15)   The core has 8 virtual processors (16-23)   The core has 8 virtual processors (24-31)   The core has 8 virtual processors (32-39)   The core has 8 virtual processors (40-47)   The core has 8 virtual processors (48-55)   The core has 8 virtual processors (56-63)     SPARC-T4 (chipid 0, clock 2848 MHz) The physical processor has 8 cores and 64 virtual processors (64-127)   The core has 8 virtual processors (64-71)   The core has 8 virtual processors (72-79)   The core has 8 virtual processors (80-87)   The core has 8 virtual processors (88-95)   The core has 8 virtual processors (96-103)   The core has 8 virtual processors (104-111)   The core has 8 virtual processors (112-119)   The core has 8 virtual processors (120-127)     SPARC-T4 (chipid 1, clock 2848 MHz) (2.2) The "before" test: without processor binding. I started with a 4-member cluster deployed into 4 Oracle Solaris Containers. Each container used a unique gigabit Ethernet port for HTTP traffic. The containers shared a 10 gigabit Ethernet port for JDBC traffic. (2.3) The "after" test: with processor binding. I ran one application server in the Global Zone and another application server in each of the three non-global zones (NGZ):  (3.0) Configuration steps. The following steps need to be repeated for all three Oracle Solaris Containers. (3.1) Stop AppServers from the BUI. (3.2) Stop the NGZ. test# ssh test-z2 init 5 (3.3) Enable resource pools: test# svcadm enable pools (3.4) Create the resource pool: test# poolcfg -dc 'create pool pool-test-z2' (3.5) Create the processor set: test# poolcfg -dc 'create pset pset-test-z2' (3.6) Specify the maximum number of CPU's that may be addd to the processor set: test# poolcfg -dc 'modify pset pset-test-z2 (uint pset.max=32)' (3.7) bash syntax to add Virtual CPUs to the processor set: test# (( i = 64 )); while (( i < 96 )); do poolcfg -dc "transfer to pset pset-test-z2 (cpu $i)"; (( i = i + 1 )) ; done (3.8) Associate the resource pool with the processor set: test# poolcfg -dc 'associate pool pool-test-z2 (pset pset-test-z2)' (3.9) Tell the zone to use the resource pool that has been created: test# zonecfg -z test-z1 set pool=pool-test-z2 (3.10) Boot the Oracle Solaris Container test# zoneadm -z test-z2 boot (3.11) Save the configuration to /etc/pooladm.conf test# pooladm -s (4.0) Results. Using the resource pools improves both throughput and response time: (5.0) References: System Administration Guide: Oracle Solaris Containers-Resource Management and Oracle Solaris Zones Capitalizing on large numbers of processors with WebSphere Portal on Solaris WebSphere Application Server and T5440 (Dileep Kumar's Weblog)  http://www.brendangregg.com/zones.html Reuters Market Data System, RMDS 6 Multiple Instances (Consolidated), Performance Test Results in Solaris, Containers/Zones Environment on Sun Blade X6270 by Amjad Khan, 2009.

  Read the article

• SQL Server script commands to check if object exists and drop it

  - by deadlydog

  Over the past couple years I’ve been keeping track of common SQL Server script commands that I use so I don’t have to constantly Google them.  Most of them are how to check if a SQL object exists before dropping it.  I thought others might find these useful to have them all in one place, so here you go: 1: --=============================== 2: -- Create a new table and add keys and constraints 3: --=============================== 4: IF NOT EXISTS (SELECT * FROM INFORMATION_SCHEMA.TABLES WHERE TABLE_NAME = 'TableName' AND TABLE_SCHEMA='dbo') 5: BEGIN 6: CREATE TABLE [dbo].[TableName] 7: ( 8: [ColumnName1] INT NOT NULL, -- To have a field auto-increment add IDENTITY(1,1) 9: [ColumnName2] INT NULL, 10: [ColumnName3] VARCHAR(30) NOT NULL DEFAULT('') 11: ) 12: 13: -- Add the table's primary key 14: ALTER TABLE [dbo].[TableName] ADD CONSTRAINT [PK_TableName] PRIMARY KEY NONCLUSTERED 15: ( 16: [ColumnName1], 17: [ColumnName2] 18: ) 19: 20: -- Add a foreign key constraint 21: ALTER TABLE [dbo].[TableName] WITH CHECK ADD CONSTRAINT [FK_Name] FOREIGN KEY 22: ( 23: [ColumnName1], 24: [ColumnName2] 25: ) 26: REFERENCES [dbo].[Table2Name] 27: ( 28: [OtherColumnName1], 29: [OtherColumnName2] 30: ) 31: 32: -- Add indexes on columns that are often used for retrieval 33: CREATE INDEX IN_ColumnNames ON [dbo].[TableName] 34: ( 35: [ColumnName2], 36: [ColumnName3] 37: ) 38: 39: -- Add a check constraint 40: ALTER TABLE [dbo].[TableName] WITH CHECK ADD CONSTRAINT [CH_Name] CHECK (([ColumnName] >= 0.0000)) 41: END 42: 43: --=============================== 44: -- Add a new column to an existing table 45: --=============================== 46: IF NOT EXISTS (SELECT * FROM INFORMATION_SCHEMA.COLUMNS where TABLE_SCHEMA='dbo' 47: AND TABLE_NAME = 'TableName' AND COLUMN_NAME = 'ColumnName') 48: BEGIN 49: ALTER TABLE [dbo].[TableName] ADD [ColumnName] INT NOT NULL DEFAULT(0) 50: 51: -- Add a description extended property to the column to specify what its purpose is. 52: EXEC sys.sp_addextendedproperty @name=N'MS_Description', 53: @value = N'Add column comments here, describing what this column is for.' , 54: @level0type=N'SCHEMA',@level0name=N'dbo', @level1type=N'TABLE', 55: @level1name = N'TableName', @level2type=N'COLUMN', 56: @level2name = N'ColumnName' 57: END 58: 59: --=============================== 60: -- Drop a table 61: --=============================== 62: IF EXISTS (SELECT * FROM INFORMATION_SCHEMA.TABLES WHERE TABLE_NAME = 'TableName' AND TABLE_SCHEMA='dbo') 63: BEGIN 64: DROP TABLE [dbo].[TableName] 65: END 66: 67: --=============================== 68: -- Drop a view 69: --=============================== 70: IF EXISTS (SELECT * FROM INFORMATION_SCHEMA.VIEWS WHERE TABLE_NAME = 'ViewName' AND TABLE_SCHEMA='dbo') 71: BEGIN 72: DROP VIEW [dbo].[ViewName] 73: END 74: 75: --=============================== 76: -- Drop a column 77: --=============================== 78: IF EXISTS (SELECT * FROM INFORMATION_SCHEMA.COLUMNS where TABLE_SCHEMA='dbo' 79: AND TABLE_NAME = 'TableName' AND COLUMN_NAME = 'ColumnName') 80: BEGIN 81: 82: -- If the column has an extended property, drop it first. 83: IF EXISTS (SELECT * FROM sys.fn_listExtendedProperty(N'MS_Description', N'SCHEMA', N'dbo', N'Table', 84: N'TableName', N'COLUMN', N'ColumnName') 85: BEGIN 86: EXEC sys.sp_dropextendedproperty @name=N'MS_Description', 87: @level0type=N'SCHEMA',@level0name=N'dbo', @level1type=N'TABLE', 88: @level1name = N'TableName', @level2type=N'COLUMN', 89: @level2name = N'ColumnName' 90: END 91: 92: ALTER TABLE [dbo].[TableName] DROP COLUMN [ColumnName] 93: END 94: 95: --=============================== 96: -- Drop Primary key constraint 97: --=============================== 98: IF EXISTS (SELECT * FROM INFORMATION_SCHEMA.TABLE_CONSTRAINTS WHERE CONSTRAINT_TYPE='PRIMARY KEY' AND TABLE_SCHEMA='dbo' 99: AND TABLE_NAME = 'TableName' AND CONSTRAINT_NAME = 'PK_Name') 100: BEGIN 101: ALTER TABLE [dbo].[TableName] DROP CONSTRAINT [PK_Name] 102: END 103: 104: --=============================== 105: -- Drop Foreign key constraint 106: --=============================== 107: IF EXISTS (SELECT * FROM INFORMATION_SCHEMA.TABLE_CONSTRAINTS WHERE CONSTRAINT_TYPE='FOREIGN KEY' AND TABLE_SCHEMA='dbo' 108: AND TABLE_NAME = 'TableName' AND CONSTRAINT_NAME = 'FK_Name') 109: BEGIN 110: ALTER TABLE [dbo].[TableName] DROP CONSTRAINT [FK_Name] 111: END 112: 113: --=============================== 114: -- Drop Unique key constraint 115: --=============================== 116: IF EXISTS (SELECT * FROM INFORMATION_SCHEMA.TABLE_CONSTRAINTS WHERE CONSTRAINT_TYPE='UNIQUE' AND TABLE_SCHEMA='dbo' 117: AND TABLE_NAME = 'TableName' AND CONSTRAINT_NAME = 'UNI_Name') 118: BEGIN 119: ALTER TABLE [dbo].[TableNames] DROP CONSTRAINT [UNI_Name] 120: END 121: 122: --=============================== 123: -- Drop Check constraint 124: --=============================== 125: IF EXISTS (SELECT * FROM INFORMATION_SCHEMA.TABLE_CONSTRAINTS WHERE CONSTRAINT_TYPE='CHECK' AND TABLE_SCHEMA='dbo' 126: AND TABLE_NAME = 'TableName' AND CONSTRAINT_NAME = 'CH_Name') 127: BEGIN 128: ALTER TABLE [dbo].[TableName] DROP CONSTRAINT [CH_Name] 129: END 130: 131: --=============================== 132: -- Drop a column's Default value constraint 133: --=============================== 134: DECLARE @ConstraintName VARCHAR(100) 135: SET @ConstraintName = (SELECT TOP 1 s.name FROM sys.sysobjects s JOIN sys.syscolumns c ON s.parent_obj=c.id 136: WHERE s.xtype='d' AND c.cdefault=s.id 137: AND parent_obj = OBJECT_ID('TableName') AND c.name ='ColumnName') 138: 139: IF @ConstraintName IS NOT NULL 140: BEGIN 141: EXEC ('ALTER TABLE [dbo].[TableName] DROP CONSTRAINT ' + @ConstraintName) 142: END 143: 144: --=============================== 145: -- Example of how to drop dynamically named Unique constraint 146: --=============================== 147: DECLARE @ConstraintName VARCHAR(100) 148: SET @ConstraintName = (SELECT TOP 1 CONSTRAINT_NAME FROM INFORMATION_SCHEMA.TABLE_CONSTRAINTS 149: WHERE CONSTRAINT_TYPE='UNIQUE' AND TABLE_SCHEMA='dbo' 150: AND TABLE_NAME = 'TableName' AND CONSTRAINT_NAME LIKE 'FirstPartOfConstraintName%') 151: 152: IF EXISTS (SELECT * FROM INFORMATION_SCHEMA.TABLE_CONSTRAINTS WHERE CONSTRAINT_TYPE='UNIQUE' AND TABLE_SCHEMA='dbo' 153: AND TABLE_NAME = 'TableName' AND CONSTRAINT_NAME = @ConstraintName) 154: BEGIN 155: EXEC ('ALTER TABLE [dbo].[TableName] DROP CONSTRAINT ' + @ConstraintName) 156: END 157: 158: --=============================== 159: -- Check for and drop a temp table 160: --=============================== 161: IF OBJECT_ID('tempdb..#TableName') IS NOT NULL DROP TABLE #TableName 162: 163: --=============================== 164: -- Drop a stored procedure 165: --=============================== 166: IF EXISTS (SELECT * FROM INFORMATION_SCHEMA.ROUTINES WHERE ROUTINE_TYPE='PROCEDURE' AND ROUTINE_SCHEMA='dbo' AND 167: ROUTINE_NAME = 'StoredProcedureName') 168: BEGIN 169: DROP PROCEDURE [dbo].[StoredProcedureName] 170: END 171: 172: --=============================== 173: -- Drop a UDF 174: --=============================== 175: IF EXISTS (SELECT * FROM INFORMATION_SCHEMA.ROUTINES WHERE ROUTINE_TYPE='FUNCTION' AND ROUTINE_SCHEMA='dbo' AND 176: ROUTINE_NAME = 'UDFName') 177: BEGIN 178: DROP FUNCTION [dbo].[UDFName] 179: END 180: 181: --=============================== 182: -- Drop an Index 183: --=============================== 184: IF EXISTS (SELECT * FROM SYS.INDEXES WHERE name = 'IndexName') 185: BEGIN 186: DROP INDEX TableName.IndexName 187: END 188: 189: --=============================== 190: -- Drop a Schema 191: --=============================== 192: IF EXISTS (SELECT * FROM INFORMATION_SCHEMA.SCHEMATA WHERE SCHEMA_NAME = 'SchemaName') 193: BEGIN 194: EXEC('DROP SCHEMA SchemaName') 195: END And here’s the same code, just not in the little code view window so that you don’t have to scroll it.--=============================== -- Create a new table and add keys and constraints --=============================== IF NOT EXISTS (SELECT * FROM INFORMATION_SCHEMA.TABLES WHERE TABLE_NAME = 'TableName' AND TABLE_SCHEMA='dbo') BEGIN CREATE TABLE [dbo].[TableName]  ( [ColumnName1] INT NOT NULL, -- To have a field auto-increment add IDENTITY(1,1) [ColumnName2] INT NULL, [ColumnName3] VARCHAR(30) NOT NULL DEFAULT('') ) -- Add the table's primary key ALTER TABLE [dbo].[TableName] ADD CONSTRAINT [PK_TableName] PRIMARY KEY NONCLUSTERED ( [ColumnName1],  [ColumnName2] ) -- Add a foreign key constraint ALTER TABLE [dbo].[TableName] WITH CHECK ADD CONSTRAINT [FK_Name] FOREIGN KEY ( [ColumnName1],  [ColumnName2] ) REFERENCES [dbo].[Table2Name]  ( [OtherColumnName1],  [OtherColumnName2] ) -- Add indexes on columns that are often used for retrieval CREATE INDEX IN_ColumnNames ON [dbo].[TableName] ( [ColumnName2], [ColumnName3] ) -- Add a check constraint ALTER TABLE [dbo].[TableName] WITH CHECK ADD CONSTRAINT [CH_Name] CHECK (([ColumnName] >= 0.0000)) END --=============================== -- Add a new column to an existing table --=============================== IF NOT EXISTS (SELECT * FROM INFORMATION_SCHEMA.COLUMNS where TABLE_SCHEMA='dbo' AND TABLE_NAME = 'TableName' AND COLUMN_NAME = 'ColumnName') BEGIN ALTER TABLE [dbo].[TableName] ADD [ColumnName] INT NOT NULL DEFAULT(0) -- Add a description extended property to the column to specify what its purpose is. EXEC sys.sp_addextendedproperty @name=N'MS_Description',  @value = N'Add column comments here, describing what this column is for.' ,  @level0type=N'SCHEMA',@level0name=N'dbo', @level1type=N'TABLE', @level1name = N'TableName', @level2type=N'COLUMN', @level2name = N'ColumnName' END --=============================== -- Drop a table --=============================== IF EXISTS (SELECT * FROM INFORMATION_SCHEMA.TABLES WHERE TABLE_NAME = 'TableName' AND TABLE_SCHEMA='dbo') BEGIN DROP TABLE [dbo].[TableName] END --=============================== -- Drop a view --=============================== IF EXISTS (SELECT * FROM INFORMATION_SCHEMA.VIEWS WHERE TABLE_NAME = 'ViewName' AND TABLE_SCHEMA='dbo') BEGIN DROP VIEW [dbo].[ViewName] END --=============================== -- Drop a column --=============================== IF EXISTS (SELECT * FROM INFORMATION_SCHEMA.COLUMNS where TABLE_SCHEMA='dbo' AND TABLE_NAME = 'TableName' AND COLUMN_NAME = 'ColumnName') BEGIN -- If the column has an extended property, drop it first. IF EXISTS (SELECT * FROM sys.fn_listExtendedProperty(N'MS_Description', N'SCHEMA', N'dbo', N'Table', N'TableName', N'COLUMN', N'ColumnName') BEGIN EXEC sys.sp_dropextendedproperty @name=N'MS_Description',  @level0type=N'SCHEMA',@level0name=N'dbo', @level1type=N'TABLE', @level1name = N'TableName', @level2type=N'COLUMN', @level2name = N'ColumnName' END ALTER TABLE [dbo].[TableName] DROP COLUMN [ColumnName] END --=============================== -- Drop Primary key constraint --=============================== IF EXISTS (SELECT * FROM INFORMATION_SCHEMA.TABLE_CONSTRAINTS WHERE CONSTRAINT_TYPE='PRIMARY KEY' AND TABLE_SCHEMA='dbo' AND TABLE_NAME = 'TableName' AND CONSTRAINT_NAME = 'PK_Name') BEGIN ALTER TABLE [dbo].[TableName] DROP CONSTRAINT [PK_Name] END --=============================== -- Drop Foreign key constraint --=============================== IF EXISTS (SELECT * FROM INFORMATION_SCHEMA.TABLE_CONSTRAINTS WHERE CONSTRAINT_TYPE='FOREIGN KEY' AND TABLE_SCHEMA='dbo' AND TABLE_NAME = 'TableName' AND CONSTRAINT_NAME = 'FK_Name') BEGIN ALTER TABLE [dbo].[TableName] DROP CONSTRAINT [FK_Name] END --=============================== -- Drop Unique key constraint --=============================== IF EXISTS (SELECT * FROM INFORMATION_SCHEMA.TABLE_CONSTRAINTS WHERE CONSTRAINT_TYPE='UNIQUE' AND TABLE_SCHEMA='dbo' AND TABLE_NAME = 'TableName' AND CONSTRAINT_NAME = 'UNI_Name') BEGIN ALTER TABLE [dbo].[TableNames] DROP CONSTRAINT [UNI_Name] END --=============================== -- Drop Check constraint --=============================== IF EXISTS (SELECT * FROM INFORMATION_SCHEMA.TABLE_CONSTRAINTS WHERE CONSTRAINT_TYPE='CHECK' AND TABLE_SCHEMA='dbo' AND TABLE_NAME = 'TableName' AND CONSTRAINT_NAME = 'CH_Name') BEGIN ALTER TABLE [dbo].[TableName] DROP CONSTRAINT [CH_Name] END --=============================== -- Drop a column's Default value constraint --=============================== DECLARE @ConstraintName VARCHAR(100) SET @ConstraintName = (SELECT TOP 1 s.name FROM sys.sysobjects s JOIN sys.syscolumns c ON s.parent_obj=c.id WHERE s.xtype='d' AND c.cdefault=s.id  AND parent_obj = OBJECT_ID('TableName') AND c.name ='ColumnName') IF @ConstraintName IS NOT NULL BEGIN EXEC ('ALTER TABLE [dbo].[TableName] DROP CONSTRAINT ' + @ConstraintName) END --=============================== -- Example of how to drop dynamically named Unique constraint --=============================== DECLARE @ConstraintName VARCHAR(100) SET @ConstraintName = (SELECT TOP 1 CONSTRAINT_NAME FROM INFORMATION_SCHEMA.TABLE_CONSTRAINTS  WHERE CONSTRAINT_TYPE='UNIQUE' AND TABLE_SCHEMA='dbo' AND TABLE_NAME = 'TableName' AND CONSTRAINT_NAME LIKE 'FirstPartOfConstraintName%') IF EXISTS (SELECT * FROM INFORMATION_SCHEMA.TABLE_CONSTRAINTS WHERE CONSTRAINT_TYPE='UNIQUE' AND TABLE_SCHEMA='dbo' AND TABLE_NAME = 'TableName' AND CONSTRAINT_NAME = @ConstraintName) BEGIN EXEC ('ALTER TABLE [dbo].[TableName] DROP CONSTRAINT ' + @ConstraintName) END --=============================== -- Check for and drop a temp table --=============================== IF OBJECT_ID('tempdb..#TableName') IS NOT NULL DROP TABLE #TableName --=============================== -- Drop a stored procedure --=============================== IF EXISTS (SELECT * FROM INFORMATION_SCHEMA.ROUTINES WHERE ROUTINE_TYPE='PROCEDURE' AND ROUTINE_SCHEMA='dbo' AND ROUTINE_NAME = 'StoredProcedureName') BEGIN DROP PROCEDURE [dbo].[StoredProcedureName] END --=============================== -- Drop a UDF --=============================== IF EXISTS (SELECT * FROM INFORMATION_SCHEMA.ROUTINES WHERE ROUTINE_TYPE='FUNCTION' AND ROUTINE_SCHEMA='dbo' AND  ROUTINE_NAME = 'UDFName') BEGIN DROP FUNCTION [dbo].[UDFName] END --=============================== -- Drop an Index --=============================== IF EXISTS (SELECT * FROM SYS.INDEXES WHERE name = 'IndexName') BEGIN DROP INDEX TableName.IndexName END --=============================== -- Drop a Schema --=============================== IF EXISTS (SELECT * FROM INFORMATION_SCHEMA.SCHEMATA WHERE SCHEMA_NAME = 'SchemaName') BEGIN EXEC('DROP SCHEMA SchemaName') END

  Read the article

• Unable to connect to Wireless after installing Ubuntu 12.10

  - by Moulik

  I am using Asus U56E laptop and after installing Ubuntu 12.10 alongside Windows 8, I am unable to connect to the Wireless. I have been trying to solve this problem since two weeks and couldn't solve it. Please help. Any answer would be appreciated. Here are some command-line results. lspci -v | grep -iA 7 network ubuntu@ubuntu:~$ lspci -v | grep -iA 7 network 02:00.0 Network controller: Intel Corporation Centrino Wireless-N + WiMAX 6150 (rev 67) Subsystem: Intel Corporation Centrino Wireless-N + WiMAX 6150 BGN Flags: bus master, fast devsel, latency 0, IRQ 52 Memory at de800000 (64-bit, non-prefetchable) [size=8K] Capabilities: <access denied> Kernel driver in use: iwlwifi Kernel modules: iwlwifi lsmod | grep iwlwifi ubuntu@ubuntu:~$ lsmod | grep iwlwifi iwlwifi 386826 0 mac80211 539908 1 iwlwifi cfg80211 206566 2 iwlwifi,mac80211 ubuntu@ubuntu:~$ dmesg | grep iwlwifi [ 57.846261] iwlwifi: Intel(R) Wireless WiFi Link AGN driver for Linux, in-tree: [ 57.846264] iwlwifi: Copyright(c) 2003-2012 Intel Corporation [ 57.846336] iwlwifi 0000:02:00.0: >pci_resource_len = 0x00002000 [ 57.846338] iwlwifi 0000:02:00.0: >pci_resource_base = ffffc90000c7c000 [ 57.846341] iwlwifi 0000:02:00.0: >HW Revision ID = 0x67 [ 57.846438] iwlwifi 0000:02:00.0: >irq 52 for MSI/MSI-X [ 59.558335] iwlwifi 0000:02:00.0: >loaded firmware version 41.28.5.1 build 33926 [ 59.558514] iwlwifi 0000:02:00.0: >CONFIG_IWLWIFI_DEBUG disabled [ 59.558516] iwlwifi 0000:02:00.0: >CONFIG_IWLWIFI_DEBUGFS enabled [ 59.558517] iwlwifi 0000:02:00.0: >CONFIG_IWLWIFI_DEVICE_TRACING enabled [ 59.558519] iwlwifi 0000:02:00.0: >CONFIG_IWLWIFI_DEVICE_TESTMODE enabled [ 59.558520] iwlwifi 0000:02:00.0: >CONFIG_IWLWIFI_P2P disabled [ 59.558522] iwlwifi 0000:02:00.0: >Detected Intel(R) Centrino(R) Wireless-N + WiMAX 6150 BGN, REV=0x84 [ 59.558583] iwlwifi 0000:02:00.0: >L1 Disabled; Enabling L0S [ 59.569083] iwlwifi 0000:02:00.0: >device EEPROM VER=0x557, CALIB=0x6 [ 59.569085] iwlwifi 0000:02:00.0: >Device SKU: 0x150 [ 59.569087] iwlwifi 0000:02:00.0: >Valid Tx ant: 0x1, Valid Rx ant: 0x3 [ 59.569100] iwlwifi 0000:02:00.0: >Tunable channels: 13 802.11bg, 0 802.11a channels [ 70.208469] iwlwifi 0000:02:00.0: >L1 Disabled; Enabling L0S [ 70.208648] iwlwifi 0000:02:00.0: >Radio type=0x1-0x2-0x0 [ 70.366319] iwlwifi 0000:02:00.0: >L1 Disabled; Enabling L0S [ 70.366470] iwlwifi 0000:02:00.0: >Radio type=0x1-0x2-0x0 sudo lshw -c network ubuntu@ubuntu:~$ sudo lshw -c network *-network description: Wireless interface product: Centrino Wireless-N + WiMAX 6150 vendor: Intel Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 67 serial: 40:25:c2:84:99:c4 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.5.0-17-generic firmware=41.28.5.1 build 33926 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:52 memory:de800000-de801fff *-network description: Ethernet interface product: AR8151 v2.0 Gigabit Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 logical name: eth0 version: c0 serial: 54:04:a6:2b:6a:ef capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI latency=0 link=no multicast=yes port=twisted pair resources: irq:54 memory:dd400000-dd43ffff ioport:a000(size=128) ifconfig ubuntu@ubuntu:~$ ifconfig eth0 Link encap:Ethernet HWaddr 54:04:a6:2b:6a:ef UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:176 errors:0 dropped:0 overruns:0 frame:0 TX packets:176 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:14368 (14.3 KB) TX bytes:14368 (14.3 KB) wlan0 Link encap:Ethernet HWaddr 40:25:c2:84:99:c4 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) iwconfig ubuntu@ubuntu:~$ iwconfig eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off iwlist scan ubuntu@ubuntu:~$ iwlist scan eth0 Interface doesn't support scanning. lo Interface doesn't support scanning. wlan0 No scan results nm-tool ubuntu@ubuntu:~$ nm-tool NetworkManager Tool State: disconnected - Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: atl1c State: unavailable Default: no HW Address: 54:04:A6:2B:6A:EF Capabilities: Carrier Detect: yes Wired Properties Carrier: off - Device: wlan0 ---------------------------------------------------------------- Type: 802.11 WiFi Driver: iwlwifi State: disconnected Default: no HW Address: 40:25:C2:84:99:C4 Capabilities: Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points hypeness2: Infra, 00:21:29:DA:08:4F, Freq 2462 MHz, Rate 54 Mb/s, Strength 42 WPA love: Infra, 68:7F:74:17:02:66, Freq 2412 MHz, Rate 54 Mb/s, Strength 19 WPA WPA2 DIRECT-MwSCX-3400Pamela: Infra, 02:15:99:A3:3F:AC, Freq 2412 MHz, Rate 54 Mb/s, Strength 22 WPA2 router: Infra, 1C:AF:F7:D6:76:F3, Freq 2417 MHz, Rate 54 Mb/s, Strength 20 WPA2 wing: Infra, E8:40:F2:34:E4:F7, Freq 2437 MHz, Rate 54 Mb/s, Strength 20 WPA WPA2 132LINKSYS: Infra, 00:1A:70:80:1F:E9, Freq 2437 MHz, Rate 54 Mb/s, Strength 57 WEP VMITTAL: Infra, E0:46:9A:3C:F0:C4, Freq 2412 MHz, Rate 54 Mb/s, Strength 27 WEP HP-Print-10-LaserJet 1025: Infra, 7C:E9:D3:7E:F8:10, Freq 2437 MHz, Rate 54 Mb/s, Strength 59 ACNBB: Infra, 00:26:75:22:A6:2F, Freq 2437 MHz, Rate 54 Mb/s, Strength 20 SATKAIVAL: Infra, 00:18:E7:CE:69:A6, Freq 2412 MHz, Rate 54 Mb/s, Strength 69 WPA WPA2 hypeness: Infra, B8:E6:25:24:C3:B1, Freq 2437 MHz, Rate 54 Mb/s, Strength 54 WPA WPA2 CSNetwork: Infra, BC:14:01:58:C5:88, Freq 2437 MHz, Rate 54 Mb/s, Strength 25 WPA WPA2 tharma: Infra, BC:14:01:E2:06:18, Freq 2412 MHz, Rate 54 Mb/s, Strength 15 WPA WPA2 Active2.4: Infra, 10:6F:3F:0E:F3:8E, Freq 2462 MHz, Rate 54 Mb/s, Strength 17 WPA WPA2 ACNBB: Infra, 00:26:75:58:4E:7A, Freq 2437 MHz, Rate 54 Mb/s, Strength 85 KO: Infra, BC:14:01:2E:AF:A8, Freq 2452 MHz, Rate 54 Mb/s, Strength 22 WPA WPA2 FEAR: Infra, 00:18:4D:C0:BC:58, Freq 2462 MHz, Rate 54 Mb/s, Strength 17 WPA Pamela: Infra, BC:14:01:52:F6:F8, Freq 2412 MHz, Rate 54 Mb/s, Strength 24 WPA WPA2 bvrk2: Infra, 78:CD:8E:7B:3C:79, Freq 2457 MHz, Rate 54 Mb/s, Strength 19 WPA WPA2 BELL030: Infra, D8:6C:E9:17:AF:09, Freq 2462 MHz, Rate 54 Mb/s, Strength 22 WPA2 Desai: Infra, 00:1D:7E:52:FB:C5, Freq 2437 MHz, Rate 54 Mb/s, Strength 14 WEP Sritharan: Infra, BC:14:01:E5:59:78, Freq 2462 MHz, Rate 54 Mb/s, Strength 19 WPA WPA2 PFN: Infra, 00:13:10:8B:CF:45, Freq 2437 MHz, Rate 54 Mb/s, Strength 19 WEP rfkill list all ubuntu@ubuntu:~$ rfkill list all 0: asus-wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: asus-wimax: WiMAX Soft blocked: yes Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no so these are some more results sudo modprobe -r iwlwifi ubuntu@ubuntu:~$ sudo modprobe -r iwlwifi sudo modprobe iwlwifi 11n_disable=1 ubuntu@ubuntu:~$ sudo modprobe iwlwifi 11n_disable=1 echo "blacklist asus_wmi" | sudo tee -a /etcmodprobe.d/blacklist.conf ubuntu@ubuntu:~$ echo "blacklist asus_wmi" | sudo tee -a /etc/modprobe.d/blacklist.conf blacklist asus_wmi echo "options iwlwifi 11n_disable=1" | sudo tee /etc/modprobe.d/iwlwifi.conf ubuntu@ubuntu:~$ echo "options iwlwifi 11n_disable=1" | sudo tee /etc/modprobe.d/iwlwifi.conf options iwlwifi 11n_disable=1 sudo modprobe -rfv iwlwifi ubuntu@ubuntu:~$ sudo modprobe -rfv iwlwifi rmmod /lib/modules/3.5.0-17-generic/kernel/drivers/net/wireless/iwlwifi/iwlwifi.ko rmmod /lib/modules/3.5.0-17-generic/kernel/net/mac80211/mac80211.ko rmmod /lib/modules/3.5.0-17-generic/kernel/net/wireless/cfg80211.ko sudo modprobe -v iwlwifi ubuntu@ubuntu:~$ sudo modprobe -v iwlwifi insmod /lib/modules/3.5.0-17-generic/kernel/net/wireless/cfg80211.ko insmod /lib/modules/3.5.0-17-generic/kernel/net/mac80211/mac80211.ko insmod /lib/modules/3.5.0-17-generic/kernel/drivers/net/wireless/iwlwifi/iwlwifi.ko 11n_disable=1

  Read the article

• CodePlex Daily Summary for Sunday, September 29, 2013

  CodePlex Daily Summary for Sunday, September 29, 2013Popular ReleasesAudioWordsDownloader: AudioWordsDownloader 1.1 build 88: New features -------- list of words (mp3 files) is available upon typing when a download path is defined list of download paths is added paths history settings added Bug fixed ----- case mismatch in word search field fixed path not exist bug fixed when history has been used path, when filled from dialog, not stored refresh autocomplete list after path change word sought is deleted when path is changed at the end sought word list is deleted word list not refreshed download end...Activity Viewer 2012: Activity Viewer 2012 V 5.0.0.3: Planning to add new features: 1. Import/Export rules 2. Tabular mode multi servers connections.Tweetinvi a friendly Twitter C# API: Alpha 0.8.3.0: Version 0.8.3.0 emphasis on the FIlteredStream and ease how to manage Exceptions that can occur due to the network or any other issue you might encounter. Will be available through nuget the 29/09/2013. FilteredStream Features provided by the Twitter Stream API - Ability to track specific keywords - Ability to track specific users - Ability to track specific locations Additional features - Detect the reasons the tweet has been retrieved from the Filtered API. You have access to both the ma...AcDown?????: AcDown????? v4.5: ??●AcDown??????????、??、??、???????。????，????，?????????????????????????。???????????Acfun、????(Bilibili)、??、??、YouTube、??、???、??????、SF????、????????????。 ●??????AcPlay?????，??????、????????????????。 ● AcDown???????C#??，????.NET Framework 2.0??。?????"Acfun?????"。 ??v4.5 ???? AcPlay????????v3.5 ????????，???????????30% ?? ???????GoodManga.net???? ?? ?????????? ?? ??Acfun?????????? ??Bilibili??????????? ?????????flvcd???????? ??SfAcg????????????? ???????????? ???????????????? ????32...OfflineBrowser: Release v1.2: This release includes some multi-threading support, a better progress bar, more JavaScript fixes, and a help system. This release is also portable (can run with no issues from a flash drive).CtrlAltStudio Viewer: CtrlAltStudio Viewer 1.0.0.34288 Release: This release of the CtrlAltStudio Viewer includes the following significant features: Stereoscopic 3D display support. Based on Firestorm viewer 4.4.2 codebase. For more details, see the release notes linked to below. Release notes: http://ctrlaltstudio.com/viewer/release-notes/1-0-0-34288-release Support info: http://ctrlaltstudio.com/viewer/support Privacy policy: http://ctrlaltstudio.com/viewer/privacy Disclaimer: This software is not provided or supported by Linden Lab, the makers of ...CrmSvcUtil Generate Attribute Constants: Generate Attribute Constants (1.0.5018.28159): Built against version 5.0.15 of the CRM SDK Fixed issue where constant for primary key attribute was being duplicated in all entity classes Added ability to override base class for entity classesC# Intellisense for Notepad++: Release v1.0.6.0: Added support for classless scripts To avoid the DLLs getting locked by OS use MSI file for the installation.CS-Script for Notepad++: Release v1.0.6.0: Added support for classless scripts To avoid the DLLs getting locked by OS use MSI file for the installation.SimpleExcelReportMaker: Serm 0.02: SourceCode and SampleMagick.NET: Magick.NET 6.8.7.001: Magick.NET linked with ImageMagick 6.8.7.0. Breaking changes: - ToBitmap method of MagickImage returns a png instead of a bmp. - Changed the value for full transparency from 255(Q8)/65535(Q16) to 0. - MagickColor now uses floats instead of Byte/UInt16.Media Companion: Media Companion MC3.578b: With the feedback received over the renaming of Movie Folders, and files, there has been some refinement done. As well as I would like to introduce Blu-Ray movie folder support, for Pre-Frodo and Frodo onwards versions of XBMC. To start with, Context menu option for renaming movies, now has three sub options: Movie & Folder, Movie only & Folder only. The option Manual Movie Rename needs to be selected from Movie Preferences, but the autoscrape boxes do not need to be selected. Blu Ray Fo...WDTVHubGen - Adds Metadata, thumbnails and subtitles to WDTV Live Hubs: WDTVHubGen v2.1.3.api release: This is for the brave at heart, this is the maint release to update to the new movie api. please send feedback on fix requests.FFXIV Crafting Simulator: Crafting Simulator 2.3: - Major refactoring of the code behind. - Added a current durability and a current CP textbox.DNN CMS Platform: 07.01.02: Major HighlightsAdded the ability to manage the Vanity URL prefix Added the ability to filter members in the member directory by role Fixed issue where the user could inadvertently click the login button multiple times Fixed issues where core classes could not be used in out of process cache provider Fixed issue where profile visibility submenu was not displayed correctly Fixed issue where the member directory was broken when Convert URL to lowercase setting was enabled Fixed issu...Rawr: Rawr 5.4.1: This is the Downloadable WPF version of Rawr!For web-based version see http://elitistjerks.com/rawr.php You can find the version notes at: http://rawr.codeplex.com/wikipage?title=VersionNotes Rawr Addon (NOT UPDATED YET FOR MOP)We now have a Rawr Official Addon for in-game exporting and importing of character data hosted on Curse. The Addon does not perform calculations like Rawr, it simply shows your exported Rawr data in wow tooltips and lets you export your character to Rawr (including ba...Sample MVC4 EF Codefirst Architecture: RazMVCWebApp ver 1.1: Signal R sample is added.CODE Framework: 4.0.30923.0: See change notes in the documentation section for details on what's new. Note: If you download the class reference help file with, you have to right-click the file, pick "Properties", and then unblock the file, as many browsers flag the file as blocked during download (for security reasons) and thus hides all content.JayData -The unified data access library for JavaScript: JayData 1.3.2 - Indian Summer Edition: JayData is a unified data access library for JavaScript to CRUD + Query data from different sources like WebAPI, OData, MongoDB, WebSQL, SQLite, HTML5 localStorage, Facebook or YQL. The library can be integrated with KendoUI, Angular.js, Knockout.js or Sencha Touch 2 and can be used on Node.js as well. See it in action in this 6 minutes video KendoUI examples: JayData example site Examples for map integration JayData example site What's new in JayData 1.3.2 - Indian Summer Edition For detai...ZXing.Net: ZXing.Net 0.12.0.0: sync with rev. 2892 of the java version new PDF417 decoder improved Aztec decoder global speed improvements direct Kinect support for ColorImageFrame better Structured Append support many other small bug fixes and improvementsNew ProjectsCACHEDB: CLIENT-DATABASE || CLIENT_CACHEDB-DATABASEClassic WiX Burn Theme: A WiX Burn theme inspired by the classic WiX wizard user interface.CryptStr.Fody: A post-build weaver that encrypts literal strings in your .NET assemblies without breaking ClickOnce.Easy Code: A setting framework.EduSoft: This is a school eg.GameStuff: GameStuff is a library of Physics and Geometrics concepts for video game. Nekora Test Project: Nekora test projectPopCorn Console Game: Simple console gameRadioController: This project started from people installing Tablets in Mustangs. You would typically loose most control of the radio. This projects brings that back!Random searcher i pochodne: Wyszukiwarka plików multimedialnych i czego dusza zapragnie.SporkRandom: A .NET (C#, Visual Basic) interface for the true random number generator service of random.org

  Read the article

• OData &ndash; The easiest service I can create: now with updates

  - by Jon Dalberg

  The other day I created a simple NastyWord service exposed via OData. It was read-only and used an in-memory backing store for the words. Today I’ll modify it to use a file instead of a list and I’ll accept new nasty words by implementing IUpdatable directly. The first thing to do is enable the service to accept new entries. This is done at configuration time by adding the “WriteAppend” access rule: 1: public class NastyWords : DataService<NastyWordsDataSource> 2: { 3: // This method is called only once to initialize service-wide policies. 4: public static void InitializeService(DataServiceConfiguration config) 5: { 6: config.SetEntitySetAccessRule("*", EntitySetRights.AllRead | EntitySetRights.WriteAppend); 7: config.DataServiceBehavior.MaxProtocolVersion = DataServiceProtocolVersion.V2; 8: } 9: }   Next I placed a file, NastyWords.txt, in the “App_Data” folder and added a few *choice* words to start. This required one simple change to our NastyWordDataSource.cs file: 1: public NastyWordsDataSource() 2: { 3: UpdateFromSource(); 4: } 5:   6: private void UpdateFromSource() 7: { 8: var words = File.ReadAllLines(pathToFile); 9: NastyWords = (from w in words 10: select new NastyWord { Word = w }).AsQueryable(); 11: }   Nothing too shocking here, just reading each line from the NastyWords.txt file and exposing them. Next, I implemented IUpdatable which comes with a boat-load of methods. We don’t need all of them for now since we are only concerned with allowing new values. Here are the methods we must implement, all the others throw a NotImplementedException: 1: public object CreateResource(string containerName, string fullTypeName) 2: { 3: var nastyWord = new NastyWord(); 4: pendingUpdates.Add(nastyWord); 5: return nastyWord; 6: } 7:   8: public object ResolveResource(object resource) 9: { 10: return resource; 11: } 12:   13: public void SaveChanges() 14: { 15: var intersect = (from w in pendingUpdates 16: select w.Word).Intersect(from n in NastyWords 17: select n.Word); 18:   19: if (intersect.Count() > 0) 20: throw new DataServiceException(500, "duplicate entry"); 21:   22: var lines = from w in pendingUpdates 23: select w.Word; 24:   25: File.AppendAllLines(pathToFile, 26: lines, 27: Encoding.UTF8); 28:   29: pendingUpdates.Clear(); 30:   31: UpdateFromSource(); 32: } 33:   34: public void SetValue(object targetResource, string propertyName, object propertyValue) 35: { 36: targetResource.GetType().GetProperty(propertyName).SetValue(targetResource, propertyValue, null); 37: }   I use a simple list to contain the pending updates and only commit them when the “SaveChanges” method is called. Here’s the order these methods are called in our service during an insert: CreateResource – here we just instantiate a new NastyWord and stick a reference to it in our pending updates list. SetValue – this is where the “Word” property of the NastyWord instance is set. SaveChanges – get the list of pending updates, barfing on duplicates, write them to the file and clear our pending list. ResolveResource – the newly created resource will be returned directly here since we aren’t dealing with “handles” to objects but the actual objects themselves. Not too bad, eh? I didn’t find this documented anywhere but a little bit of digging in the OData spec and use of Fiddler made it pretty easy to figure out. Here is some client code which would add a new nasty word: 1: static void Main(string[] args) 2: { 3: var svc = new ServiceReference1.NastyWordsDataSource(new Uri("http://localhost.:60921/NastyWords.svc")); 4: svc.AddToNastyWords(new ServiceReference1.NastyWord() { Word = "shat" }); 5:   6: svc.SaveChanges(); 7: }   Here’s all of the code so far for to implement the service: 1: using System; 2: using System.Collections.Generic; 3: using System.Data.Services; 4: using System.Data.Services.Common; 5: using System.Linq; 6: using System.ServiceModel.Web; 7: using System.Web; 8: using System.IO; 9: using System.Text; 10:   11: namespace ONasty 12: { 13: [DataServiceKey("Word")] 14: public class NastyWord 15: { 16: public string Word { get; set; } 17: } 18:   19: public class NastyWordsDataSource : IUpdatable 20: { 21: private List<NastyWord> pendingUpdates = new List<NastyWord>(); 22: private string pathToFile = @"path to your\App_Data\NastyWords.txt"; 23:   24: public NastyWordsDataSource() 25: { 26: UpdateFromSource(); 27: } 28:   29: private void UpdateFromSource() 30: { 31: var words = File.ReadAllLines(pathToFile); 32: NastyWords = (from w in words 33: select new NastyWord { Word = w }).AsQueryable(); 34: } 35:   36: public IQueryable<NastyWord> NastyWords { get; private set; } 37:   38: public void AddReferenceToCollection(object targetResource, string propertyName, object resourceToBeAdded) 39: { 40: throw new NotImplementedException(); 41: } 42:   43: public void ClearChanges() 44: { 45: pendingUpdates.Clear(); 46: } 47:   48: public object CreateResource(string containerName, string fullTypeName) 49: { 50: var nastyWord = new NastyWord(); 51: pendingUpdates.Add(nastyWord); 52: return nastyWord; 53: } 54:   55: public void DeleteResource(object targetResource) 56: { 57: throw new NotImplementedException(); 58: } 59:   60: public object GetResource(IQueryable query, string fullTypeName) 61: { 62: throw new NotImplementedException(); 63: } 64:   65: public object GetValue(object targetResource, string propertyName) 66: { 67: throw new NotImplementedException(); 68: } 69:   70: public void RemoveReferenceFromCollection(object targetResource, string propertyName, object resourceToBeRemoved) 71: { 72: throw new NotImplementedException(); 73: } 74:   75: public object ResetResource(object resource) 76: { 77: throw new NotImplementedException(); 78: } 79:   80: public object ResolveResource(object resource) 81: { 82: return resource; 83: } 84:   85: public void SaveChanges() 86: { 87: var intersect = (from w in pendingUpdates 88: select w.Word).Intersect(from n in NastyWords 89: select n.Word); 90:   91: if (intersect.Count() > 0) 92: throw new DataServiceException(500, "duplicate entry"); 93:   94: var lines = from w in pendingUpdates 95: select w.Word; 96:   97: File.AppendAllLines(pathToFile, 98: lines, 99: Encoding.UTF8); 100:   101: pendingUpdates.Clear(); 102:   103: UpdateFromSource(); 104: } 105:   106: public void SetReference(object targetResource, string propertyName, object propertyValue) 107: { 108: throw new NotImplementedException(); 109: } 110:   111: public void SetValue(object targetResource, string propertyName, object propertyValue) 112: { 113: targetResource.GetType().GetProperty(propertyName).SetValue(targetResource, propertyValue, null); 114: } 115: } 116:   117: public class NastyWords : DataService<NastyWordsDataSource> 118: { 119: // This method is called only once to initialize service-wide policies. 120: public static void InitializeService(DataServiceConfiguration config) 121: { 122: config.SetEntitySetAccessRule("*", EntitySetRights.AllRead | EntitySetRights.WriteAppend); 123: config.DataServiceBehavior.MaxProtocolVersion = DataServiceProtocolVersion.V2; 124: } 125: } 126: } Next time we’ll allow removing nasty words. Enjoy!

  Read the article

• kernel module compiling error

  - by wati

  sh@ubuntu:/home/ccpp/helloworld$ make gcc-4.6 -O2 -DMODULE -D_KERNEL_ -W -Wall -Wstrict-prototypes -Wmissing-prototypes -isystem /lib/modules/`uname -r`/build/include -c -o hello-1.o hello-1.c hello-1.c:4:0: warning: "MODULE" redefined [enabled by default] <command-line>:0:0: note: this is the location of the previous definition hello-1.c:6:0: warning: "_KERNEL_" redefined [enabled by default] <command-line>:0:0: note: this is the location of the previous definition In file included from /lib/modules/3.2.0-25-generic/build/include/linux/list.h:4:0, from /lib/modules/3.2.0-25-generic/build/include/linux/module.h:9, from hello-1.c:7: /lib/modules/3.2.0-25-generic/build/include/linux/types.h:13:2: warning: #warning "Attempt to use kernel headers from user space, see http://kernelnewbies.org/KernelHeaders" [-Wcpp] In file included from /lib/modules/3.2.0-25-generic/build/include/linux/module.h:9:0, from hello-1.c:7: /lib/modules/3.2.0-25-generic/build/include/linux/list.h: In function ‘INIT_LIST_HEAD’: /lib/modules/3.2.0-25-generic/build/include/linux/list.h:26:6: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:27:6: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h: In function ‘__list_add’: /lib/modules/3.2.0-25-generic/build/include/linux/list.h:41:6: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:42:5: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:43:5: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:44:6: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h: In function ‘list_add’: /lib/modules/3.2.0-25-generic/build/include/linux/list.h:62:28: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h: In function ‘list_add_tail’: /lib/modules/3.2.0-25-generic/build/include/linux/list.h:76:22: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h: In function ‘__list_del’: /lib/modules/3.2.0-25-generic/build/include/linux/list.h:88:6: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:89:6: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h: In function ‘__list_del_entry’: /lib/modules/3.2.0-25-generic/build/include/linux/list.h:101:18: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:101:31: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h: In function ‘list_del’: /lib/modules/3.2.0-25-generic/build/include/linux/list.h:106:18: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:106:31: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:107:7: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:108:7: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h: In function ‘list_replace’: /lib/modules/3.2.0-25-generic/build/include/linux/list.h:125:5: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:125:17: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:126:5: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:127:5: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:127:17: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:128:5: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h: In function ‘list_is_last’: /lib/modules/3.2.0-25-generic/build/include/linux/list.h:179:13: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h: In function ‘list_empty’: /lib/modules/3.2.0-25-generic/build/include/linux/list.h:188:13: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h: In function ‘list_empty_careful’: /lib/modules/3.2.0-25-generic/build/include/linux/list.h:206:31: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:207:40: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h: In function ‘list_rotate_left’: /lib/modules/3.2.0-25-generic/build/include/linux/list.h:219:15: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h: In function ‘list_is_singular’: /lib/modules/3.2.0-25-generic/build/include/linux/list.h:230:35: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:230:49: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h: In function ‘__list_cut_position’: /lib/modules/3.2.0-25-generic/build/include/linux/list.h:236:37: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:237:6: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:237:19: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:238:6: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:239:6: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:240:7: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:241:6: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:242:11: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h: In function ‘list_cut_position’: /lib/modules/3.2.0-25-generic/build/include/linux/list.h:265:8: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h: In function ‘__list_splice’: /lib/modules/3.2.0-25-generic/build/include/linux/list.h:277:32: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:278:31: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:280:7: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:281:6: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:283:6: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:284:6: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h: In function ‘list_splice’: /lib/modules/3.2.0-25-generic/build/include/linux/list.h:296:33: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h: In function ‘list_splice_tail’: /lib/modules/3.2.0-25-generic/build/include/linux/list.h:308:27: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h: In function ‘list_splice_init’: /lib/modules/3.2.0-25-generic/build/include/linux/list.h:322:33: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h: In function ‘list_splice_tail_init’: /lib/modules/3.2.0-25-generic/build/include/linux/list.h:339:27: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h: In function ‘INIT_HLIST_NODE’: /lib/modules/3.2.0-25-generic/build/include/linux/list.h:572:3: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:573:3: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h: In function ‘hlist_unhashed’: /lib/modules/3.2.0-25-generic/build/include/linux/list.h:578:11: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h: In function ‘hlist_empty’: /lib/modules/3.2.0-25-generic/build/include/linux/list.h:583:11: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h: In function ‘__hlist_del’: /lib/modules/3.2.0-25-generic/build/include/linux/list.h:588:29: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:589:31: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:592:7: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h: In function ‘hlist_del’: /lib/modules/3.2.0-25-generic/build/include/linux/list.h:598:3: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:599:3: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h: In function ‘hlist_add_head’: /lib/modules/3.2.0-25-generic/build/include/linux/list.h:612:30: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:613:3: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:615:8: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:615:20: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:616:3: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:617:3: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:617:15: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h: In function ‘hlist_add_before’: /lib/modules/3.2.0-25-generic/build/include/linux/list.h:624:3: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:624:17: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:625:3: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:626:6: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:626:18: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:627:5: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h: In function ‘hlist_add_after’: /lib/modules/3.2.0-25-generic/build/include/linux/list.h:633:6: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:633:16: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:634:3: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:635:6: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:635:18: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:637:9: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:638:7: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:638:29: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h: In function ‘hlist_add_fake’: /lib/modules/3.2.0-25-generic/build/include/linux/list.h:644:3: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:644:15: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h: In function ‘hlist_move_list’: /lib/modules/3.2.0-25-generic/build/include/linux/list.h:654:5: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:654:18: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:655:9: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:656:6: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:656:27: error: dereferencing pointer to incomplete type /lib/modules/3.2.0-25-generic/build/include/linux/list.h:657:5: error: dereferencing pointer to incomplete type In file included from /lib/modules/3.2.0-25-generic/build/include/linux/module.h:12:0, from hello-1.c:7: /lib/modules/3.2.0-25-generic/build/include/linux/cache.h: At top level: /lib/modules/3.2.0-25-generic/build/include/linux/cache.h:5:23: fatal error: asm/cache.h: No such file or directory compilation terminated. make: *** [hello-1.o] Error 1 i got this error after compiling an helloworld program my program is #define MODULE #define LINUX #define _KERNEL_ #include <linux/module.h> #include <linux/kernel.h> int init_module(void) { printk("<1>hello World 1.\n"); return 0; } void cleanup_module(void) { printk(KERN_ALERT "goodbye world 1.\n"); } MODULE_LICENSE("GPL"); my make file is: TARGET := hello-1 WARN := -W -Wall -Wstrict-prototypes -Wmissing-prototypes INCLUDE := -isystem /lib/modules/`uname -r`/build/include CFLAGS := -O2 -DMODULE -D_KERNEL_ ${WARN} ${INCLUDE} CC := gcc-4.6 ${TARGET}.o: ${TARGET}.c .PHONY: clean clean: rm -rf ${TARGET}.o iam usin kernel 3.2.0.25 as novice i can't able to figure out where the problem is I SEARCHED EVERY THING I CAN TO KNOW ABOUT THIS ERROR BUT I CANT UNDERSTAND &I GET IRRELEVANT DOCS anybody help me please

  Read the article

• CodePlex Daily Summary for Wednesday, October 02, 2013

  CodePlex Daily Summary for Wednesday, October 02, 2013Popular ReleasesEla, functional programming language: Ela, dynamic functional language (PDF, book, 0.6): A book about Ela, dynamic functional language in PDF format.Compact 2013 Tools: Managed Code Version of Apps 1.0: Compact13MinShell Download https://download-codeplex.sec.s-msft.com/Images/v20779/RuntimeBinary.gif Compact13MinShellV3.0.zip The Codeplex Project Downloads Page AboutCompact13Tools.zip: Each app as an OS Content Subproject. Includes CoreCon3 Subproject. Apps.zip: Just the apps in a a zip file AppInstallersx86.zip: The apps as separate x86 installers Compact13MinShell Download: (Separate Codeplex Project) The Minshell that implements the menu that includes these apps via registr...Application Architecture Guidelines: App Architecture Guidelines 3.0.8: This document is an overview of software qualities, principles, patterns, practices, tools and libraries.C# Intellisense for Notepad++: Release v1.0.7.0: - smart indentation - document formatting To avoid the DLLs getting locked by OS use MSI file for the installation.CS-Script for Notepad++: Release v1.0.7.0: - smart indentation - document formatting To avoid the DLLs getting locked by OS use MSI file for the installation.State of Decay Save Manager: Version 1.0.2: Added Start/Stop button for timer to manually enable/disable Quick save routine updated to force it to refresh the folder date Quick save added to backup listing Manual update button Lower level hooking for F5 and F9 buttons workingSharePoint Farm documentation tool: SPDocumentor 0.1: SPDocumentor 0.1 This is a POC version of the tool that will be implemented.DotNetNuke® Form and List: 06.00.06: DotNetNuke Form and List 06.00.06 Changes to 6.0.6•Add in Sql to remove 'text on row' setting for UserDefinedTable to make SQL Azure compatible. •Add new azureCompatible element to manifest. •Added a fix for importing templates. Changes to 6.0.2•Fix: MakeThumbnail was broken if the application pool was configured to .Net 4 •Change: Data is now stored in nvarchar(max) instead of ntext Changes to 6.0.1•Scripts now compatible with SQL Azure. Changes to 6.0.0•Icons are shown in module action b...BlackJumboDog: Ver5.9.6: 2013.09.30 Ver5.9.6 (1)SMTP???????、???????????????? (2)WinAPI??????? (3)Web???????CGI???????????????????????Microsoft Ajax Minifier: Microsoft Ajax Minifier 5.2: Mostly internal code tweaks. added -nosize switch to turn off the size- and gzip-calculations done after minification. removed the comments in the build targets script for the old AjaxMin build task (discussion #458831). Fixed an issue with extended Unicode characters encoded inside a string literal with adjacent \uHHHH\uHHHH sequences. Fixed an IndexOutOfRange exception when encountering a CSS identifier that's a single underscore character (_). In previous builds, the net35 and net20...AJAX Control Toolkit: September 2013 Release: AJAX Control Toolkit Release Notes - September 2013 Release (Updated) Version 7.1001September 2013 release of the AJAX Control Toolkit. AJAX Control Toolkit .NET 4.5 – AJAX Control Toolkit for .NET 4.5 and sample site (Recommended). AJAX Control Toolkit .NET 4 – AJAX Control Toolkit for .NET 4 and sample site (Recommended). AJAX Control Toolkit .NET 3.5 – AJAX Control Toolkit for .NET 3.5 and sample site (Recommended). Important UpdateThis release has been updated to fix two issues: Upda...WDTVHubGen - Adds Metadata, thumbnails and subtitles to WDTV Live Hubs: WDTVHubGen.v2.1.4.apifix-alpha: WDTVHubGen.v2.1.4.apifix-alpha is for testers to figure out if we got the NEW api plugged in ok. thanksVisual Log Parser: VisualLogParser: Portable Visual Log Parser for Dotnet 4.0Trace Reader for Microsoft Dynamics CRM: Trace Reader (1.2013.9.29): Initial releaseAudioWordsDownloader: AudioWordsDownloader 1.1 build 88: New features list of words (mp3 files) is available upon typing when a download path is defined list of download paths is added paths history settings added Bug fixed case mismatch in word search field fixed path not exist bug fixed when history has been used path, when filled from dialog, not stored refresh autocomplete list after path change word sought is deleted when path is changed at the end sought word list is deleted word list not refreshed download ends. word lis...Wsus Package Publisher: Release v1.3.1309.28: Fix a bug, where WPP crash when running on a computer where Windows was installed in another language than Fr, En or De, and launching the Update Creation Wizard. Fix a bug, where WPP crash if some Multi-Thread job are launch with more than 64 items. Add a button to abort "Install This Update" wizard. Allow WPP to remember which columns are shown last time. Make URL clickable on the Update Information Tab. Add a new feature, when Double-Clicking on an update, the default action exec...Tweetinvi a friendly Twitter C# API: Alpha 0.8.3.0: Version 0.8.3.0 emphasis on the FIlteredStream and ease how to manage Exceptions that can occur due to the network or any other issue you might encounter. Will be available through nuget the 29/09/2013. FilteredStream Features provided by the Twitter Stream API - Ability to track specific keywords - Ability to track specific users - Ability to track specific locations Additional features - Detect the reasons the tweet has been retrieved from the Filtered API. You have access to both the ma...AcDown?????: AcDown????? v4.5: ??●AcDown??????????、??、??、???????。????，????，?????????????????????????。???????????Acfun、????(Bilibili)、??、??、YouTube、??、???、??????、SF????、????????????。 ●??????AcPlay?????，??????、????????????????。 ● AcDown???????C#??，????.NET Framework 2.0??。?????"Acfun?????"。 ??v4.5 ???? AcPlay????????v3.5 ????????，???????????30% ?? ???????GoodManga.net???? ?? ?????????? ?? ??Acfun?????????? ??Bilibili??????????? ?????????flvcd???????? ??SfAcg????????????? ???????????? ???????????????? ????32...Magick.NET: Magick.NET 6.8.7.001: Magick.NET linked with ImageMagick 6.8.7.0. Breaking changes: - ToBitmap method of MagickImage returns a png instead of a bmp. - Changed the value for full transparency from 255(Q8)/65535(Q16) to 0. - MagickColor now uses floats instead of Byte/UInt16.Media Companion: Media Companion MC3.578b: With the feedback received over the renaming of Movie Folders, and files, there has been some refinement done. As well as I would like to introduce Blu-Ray movie folder support, for Pre-Frodo and Frodo onwards versions of XBMC. To start with, Context menu option for renaming movies, now has three sub options: Movie & Folder, Movie only & Folder only. The option Manual Movie Rename needs to be selected from Movie Preferences, but the autoscrape boxes do not need to be selected. Blu Ray Fo...New ProjectsAll CRM Resources for Microsoft Dynamics CRM: Microsoft Dynamics CRM Resources Windows 8 App with News, Feeds, Forums, Blogs, Videos & Twitter updates, information, guides & resources #MSDynCRM community.BasiliskBugTracker: A sample teamwork project for the Telerik Academy's ASP.NET Course 2013.CagerAutoPilot: Programmatically control a toy helicopter with kinectClass Libraries & Database Management: ClassDBManager permette la sincronizzazione delle classi (creazione/modifica/cancellazione) in base alle tabelle contenute nel databaseCommand Line Utility: Enables fast, easy creation of object-oriented settings classes in C# that interface directly with command line input. Minimize code and increase robustness.Controles | Versa: Login Pagina Principal Cadastro UsuáriosDispage: DisPage is a system to hide a website under a different browser title (For example "Vimeo" could look like "Google" (I am working on a way of changing this)ExpressiveDataGenerators: Expressive and powerfull test data generators.Fabrikam Fiber: This project provides download and support to anyone (i.e. trainers) who want to access the Fabrikam Fiber sample application, setup scripts, notes, etc.Get all numbers in between a pair of numbers: Get all integers between two numbers. C#, VB.NETHungryCrowd food lovers market: food lovers market, food, marketsInvalid User Details for SharePoint 2007 and 2010 Sites: Client Based Utility to export invalid users from a SharePoint site (2007 and 2010), as a CSV file using native SP Web Services (UserGroup.asmx and People.asmx)Kh?o Sát Công Ngh?: 1. Tên d? tài: Th?c tr?ng và gi?i pháp h? tr? nâng cao nang l?c c?nh tranh c?a các doanh nghi?p nh? và v?a t?nh Thanh Hóa Lightning: Micro toolkit to make it easy to get content on your site, and serve it fast.LovelyCMS: LovelyCMS ist ein sehr einfaches Content Management System auf der Basis von ASP.NET MVC4.MVC Error Handler: Simple library that allows you to easily create error pages for common HTTP error and application exceptions.MVC Table Styling selection to CSS and demo table: Enter table styling by selection from drop-down list and both generated CSS and see effect of the CSS on a demo table.MvcWebApiFramework: main frameworkNoDemo: It is not only a demo.NumbersInWordsRU: ?????? ??? ??????????? ????? ??????? ? ????? ????????Omnifactotum: Omnifactotum is the .NET library intended to help .NET developers avoid writing the same helper types, methods and extension methods for different projects.Outlook Rules Offline Processor: A utility for organizing Microsoft Outlook rules. The utility uses the rules export file, *.RWZ, to make changes.SharePoint Farm documentation tool: The SPDocumentor (SharePoint Farm documentation tool) allows you to generate a word document that includes most of your farm settings. Startup Shutdown Mailer: This tool is a simple Windows Service which sends an e-mail to a specified account whenever your PC was started up or shut down.YüzKitabi: Daha güvenli ve etkilesimli YüzKitabi Uygulamasi

  Read the article

• xrandr doesn’t detect display ports

  - by Psyhister

  I have a ThinkPad T510 laptop with Gentoo Linux installed on it and I can’t manage to get VGA and DisplayPort working. xrandr -q won’t show them, so I’m guessing, that there’s a problem with my kernel configuration, but I wasn’t able to find the options responsible for these ports. Here’s the output from xrandr -q: xrandr: Failed to get size of gamma for output default Screen 0: minimum 320 x 175, current 1366 x 768, maximum 1366 x 768 default connected 1366x768+0+0 0mm x 0mm 1366x768 50.0* 51.0 52.0 1024x768 53.0 54.0 832x624 55.0 800x600 56.0 57.0 58.0 59.0 60.0 720x400 61.0 700x525 62.0 640x512 63.0 64.0 640x480 65.0 66.0 67.0 68.0 69.0 640x400 70.0 640x350 71.0 576x432 72.0 512x384 73.0 74.0 75.0 76.0 77.0 416x312 78.0 400x300 79.0 80.0 81.0 82.0 83.0 360x200 84.0 320x240 85.0 86.0 87.0 88.0 320x200 89.0 320x175 90.0 Can anyone help me figure out what the problem is and how to get the video connections to work?

  Read the article

• migration from jboss4.0.5GA to jboss5.1.0 GA

  - by rahul c

  Hi, Currently we have migrated from jboss4.0.5GA to jboss5.1.0 GA.Our application runs under jboss4.0.5GA well.The reason for migration to enable web service. I cann't find a way to create a web service on jboss 4.0.5 GA. while running on jboss 5.1.0 GA with jbossws-cxf-3.2.1.GA installed on it. i got following error 18:53:43,699 INFO [STDOUT] 2009-11-30 18:53:43,699 INFO org.springframework.core.CollectionFactory - JDK 1.4+ collections available 18:53:43,700 INFO [STDOUT] 2009-11-30 18:53:43,700 INFO org.springframework.core.CollectionFactory - Commons Collections 3.x available 18:53:43,973 INFO [STDOUT] 2009-11-30 18:53:43,972 INFO org.springframework.beans.factory.xml.XmlBeanDefinitionReader - Loading XML bean definitions from ServletContext resource [/WEB-INF/applicationContext.xml] 18:53:44,308 INFO [STDOUT] 2009-11-30 18:53:44,302 ERROR org.springframework.web.context.ContextLoader - Context initialization failed org.springframework.beans.factory.BeanDefinitionStoreException: Unexpected exception parsing XML document from ServletContext resource [/WEB-INF/applicationContext.xml]; nested exception is java.lang.IllegalArgumentException: Class [org.apache.cxf.transport.http_jetty.spring.NamespaceHandler] does not implement the NamespaceHandler interface Caused by: java.lang.IllegalArgumentException: Class [org.apache.cxf.transport.http_jetty.spring.NamespaceHandler] does not implement the NamespaceHandler interface at org.springframework.beans.factory.xml.DefaultNamespaceHandlerResolver.initHandlerMappings(DefaultNamespaceHandlerResolver.java:119) at org.springframework.beans.factory.xml.DefaultNamespaceHandlerResolver.(DefaultNamespaceHandlerResolver.java:96) at org.springframework.beans.factory.xml.DefaultNamespaceHandlerResolver.(DefaultNamespaceHandlerResolver.java:82) at org.springframework.beans.factory.xml.XmlBeanDefinitionReader.createDefaultNamespaceHandlerResolver(XmlBeanDefinitionReader.java:526) at org.springframework.beans.factory.xml.XmlBeanDefinitionReader.createReaderContext(XmlBeanDefinitionReader.java:515) at org.springframework.beans.factory.xml.XmlBeanDefinitionReader.registerBeanDefinitions(XmlBeanDefinitionReader.java:495) at org.springframework.beans.factory.xml.XmlBeanDefinitionReader.doLoadBeanDefinitions(XmlBeanDefinitionReader.java:390) at org.springframework.beans.factory.xml.XmlBeanDefinitionReader.loadBeanDefinitions(XmlBeanDefinitionReader.java:340) at org.springframework.beans.factory.xml.XmlBeanDefinitionReader.loadBeanDefinitions(XmlBeanDefinitionReader.java:317) at org.springframework.beans.factory.support.AbstractBeanDefinitionReader.loadBeanDefinitions(AbstractBeanDefinitionReader.java:125) at org.springframework.beans.factory.support.AbstractBeanDefinitionReader.loadBeanDefinitions(AbstractBeanDefinitionReader.java:141) at org.springframework.web.context.support.XmlWebApplicationContext.loadBeanDefinitions(XmlWebApplicationContext.java:123) at org.springframework.web.context.support.XmlWebApplicationContext.loadBeanDefinitions(XmlWebApplicationContext.java:91) at org.springframework.context.support.AbstractRefreshableApplicationContext.refreshBeanFactory(AbstractRefreshableApplicationContext.java:94) at org.springframework.context.support.AbstractApplicationContext.refresh(AbstractApplicationContext.java:292) at org.springframework.web.context.support.AbstractRefreshableWebApplicationContext.refresh(AbstractRefreshableWebApplicationContext.java:156) at org.springframework.web.context.ContextLoader.createWebApplicationContext(ContextLoader.java:246) at org.springframework.web.context.ContextLoader.initWebApplicationContext(ContextLoader.java:184) at org.springframework.web.context.ContextLoaderListener.contextInitialized(ContextLoaderListener.java:49) at org.apache.catalina.core.StandardContext.listenerStart(StandardContext.java:3910) at org.apache.catalina.core.StandardContext.start(StandardContext.java:4393) at org.jboss.web.tomcat.service.deployers.TomcatDeployment.performDeployInternal(TomcatDeployment.java:310) at org.jboss.web.tomcat.service.deployers.TomcatDeployment.performDeploy(TomcatDeployment.java:142) at org.jboss.web.deployers.AbstractWarDeployment.start(AbstractWarDeployment.java:461) at org.jboss.web.deployers.WebModule.startModule(WebModule.java:118) at org.jboss.web.deployers.WebModule.start(WebModule.java:97) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:597) at org.jboss.mx.interceptor.ReflectedDispatcher.invoke(ReflectedDispatcher.java:157) at org.jboss.mx.server.Invocation.dispatch(Invocation.java:96) at org.jboss.mx.server.Invocation.invoke(Invocation.java:88) at org.jboss.mx.server.AbstractMBeanInvoker.invoke(AbstractMBeanInvoker.java:264) at org.jboss.mx.server.MBeanServerImpl.invoke(MBeanServerImpl.java:668) at org.jboss.system.microcontainer.ServiceProxy.invoke(ServiceProxy.java:206) at $Proxy38.start(Unknown Source) at org.jboss.system.microcontainer.StartStopLifecycleAction.installAction(StartStopLifecycleAction.java:42) at org.jboss.system.microcontainer.StartStopLifecycleAction.installAction(StartStopLifecycleAction.java:37) at org.jboss.dependency.plugins.action.SimpleControllerContextAction.simpleInstallAction(SimpleControllerContextAction.java:62) at org.jboss.dependency.plugins.action.AccessControllerContextAction.install(AccessControllerContextAction.java:71) at org.jboss.dependency.plugins.AbstractControllerContextActions.install(AbstractControllerContextActions.java:51) at org.jboss.dependency.plugins.AbstractControllerContext.install(AbstractControllerContext.java:348) at org.jboss.system.microcontainer.ServiceControllerContext.install(ServiceControllerContext.java:286) at org.jboss.dependency.plugins.AbstractController.install(AbstractController.java:1631) at org.jboss.dependency.plugins.AbstractController.incrementState(AbstractController.java:934) at org.jboss.dependency.plugins.AbstractController.resolveContexts(AbstractController.java:1082) at org.jboss.dependency.plugins.AbstractController.resolveContexts(AbstractController.java:984) at org.jboss.dependency.plugins.AbstractController.change(AbstractController.java:822) at org.jboss.dependency.plugins.AbstractController.change(AbstractController.java:553) at org.jboss.system.ServiceController.doChange(ServiceController.java:688) at org.jboss.system.ServiceController.start(ServiceController.java:460) at org.jboss.system.deployers.ServiceDeployer.start(ServiceDeployer.java:163) at org.jboss.system.deployers.ServiceDeployer.deploy(ServiceDeployer.java:99) at org.jboss.system.deployers.ServiceDeployer.deploy(ServiceDeployer.java:46) at org.jboss.deployers.spi.deployer.helpers.AbstractSimpleRealDeployer.internalDeploy(AbstractSimpleRealDeployer.java:62) at org.jboss.deployers.spi.deployer.helpers.AbstractRealDeployer.deploy(AbstractRealDeployer.java:50) at org.jboss.deployers.plugins.deployers.DeployerWrapper.deploy(DeployerWrapper.java:171) at org.jboss.deployers.plugins.deployers.DeployersImpl.doDeploy(DeployersImpl.java:1439) at org.jboss.deployers.plugins.deployers.DeployersImpl.doInstallParentFirst(DeployersImpl.java:1157) at org.jboss.deployers.plugins.deployers.DeployersImpl.doInstallParentFirst(DeployersImpl.java:1178) at org.jboss.deployers.plugins.deployers.DeployersImpl.install(DeployersImpl.java:1098) at org.jboss.dependency.plugins.AbstractControllerContext.install(AbstractControllerContext.java:348) at org.jboss.dependency.plugins.AbstractController.install(AbstractController.java:1631) at org.jboss.dependency.plugins.AbstractController.incrementState(AbstractController.java:934) at org.jboss.dependency.plugins.AbstractController.resolveContexts(AbstractController.java:1082) at org.jboss.dependency.plugins.AbstractController.resolveContexts(AbstractController.java:984) at org.jboss.dependency.plugins.AbstractController.change(AbstractController.java:822) at org.jboss.dependency.plugins.AbstractController.change(AbstractController.java:553) at org.jboss.deployers.plugins.deployers.DeployersImpl.process(DeployersImpl.java:781) at org.jboss.deployers.plugins.main.MainDeployerImpl.process(MainDeployerImpl.java:702) at org.jboss.system.server.profileservice.repository.MainDeployerAdapter.process(MainDeployerAdapter.java:117) at org.jboss.system.server.profileservice.repository.ProfileDeployAction.install(ProfileDeployAction.java:70) at org.jboss.system.server.profileservice.repository.AbstractProfileAction.install(AbstractProfileAction.java:53) at org.jboss.system.server.profileservice.repository.AbstractProfileService.install(AbstractProfileService.java:361) at org.jboss.dependency.plugins.AbstractControllerContext. 18:53:44,313 INFO [STDOUT] install(AbstractControllerContext.java:348) at org.jboss.dependency.plugins.AbstractController.install(AbstractController.java:1631) at org.jboss.dependency.plugins.AbstractController.incrementState(AbstractController.java:934) at org.jboss.dependency.plugins.AbstractController.resolveContexts(AbstractController.java:1082) at org.jboss.dependency.plugins.AbstractController.resolveContexts(AbstractController.java:984) at org.jboss.dependency.plugins.AbstractController.change(AbstractController.java:822) at org.jboss.dependency.plugins.AbstractController.change(AbstractController.java:553) at org.jboss.system.server.profileservice.repository.AbstractProfileService.activateProfile(AbstractProfileService.java:306) at org.jboss.system.server.profileservice.ProfileServiceBootstrap.start(ProfileServiceBootstrap.java:271) at org.jboss.bootstrap.AbstractServerImpl.start(AbstractServerImpl.java:461) at org.jboss.Main.boot(Main.java:221) at org.jboss.Main$1.run(Main.java:556) at java.lang.Thread.run(Thread.java:619) 18:53:44,315 ERROR [[/smartLMS]] Exception sending context initialized event to listener instance of class org.springframework.web.context.ContextLoaderListener org.springframework.beans.factory.BeanDefinitionStoreException: Unexpected exception parsing XML document from ServletContext resource [/WEB-INF/applicationContext.xml]; nested exception is java.lang.IllegalArgumentException: Class [org.apache.cxf.transport.http_jetty.spring.NamespaceHandler] does not implement the NamespaceHandler interface Caused by: java.lang.IllegalArgumentException: Class [org.apache.cxf.transport.http_jetty.spring.NamespaceHandler] does not implement the NamespaceHandler interface at org.springframework.beans.factory.xml.DefaultNamespaceHandlerResolver.initHandlerMappings(DefaultNamespaceHandlerResolver.java:119) at org.springframework.beans.factory.xml.DefaultNamespaceHandlerResolver.(DefaultNamespaceHandlerResolver.java:96) at org.springframework.beans.factory.xml.DefaultNamespaceHandlerResolver.(DefaultNamespaceHandlerResolver.java:82) at org.springframework.beans.factory.xml.XmlBeanDefinitionReader.createDefaultNamespaceHandlerResolver(XmlBeanDefinitionReader.java:526) at org.springframework.beans.factory.xml.XmlBeanDefinitionReader.createReaderContext(XmlBeanDefinitionReader.java:515) at org.springframework.beans.factory.xml.XmlBeanDefinitionReader.registerBeanDefinitions(XmlBeanDefinitionReader.java:495) at org.springframework.beans.factory.xml.XmlBeanDefinitionReader.doLoadBeanDefinitions(XmlBeanDefinitionReader.java:390) at org.springframework.beans.factory.xml.XmlBeanDefinitionReader.loadBeanDefinitions(XmlBeanDefinitionReader.java:340) at org.springframework.beans.factory.xml.XmlBeanDefinitionReader.loadBeanDefinitions(XmlBeanDefinitionReader.java:317) at org.springframework.beans.factory.support.AbstractBeanDefinitionReader.loadBeanDefinitions(AbstractBeanDefinitionReader.java:125) at org.springframework.beans.factory.support.AbstractBeanDefinitionReader.loadBeanDefinitions(AbstractBeanDefinitionReader.java:141) at org.springframework.web.context.support.XmlWebApplicationContext.loadBeanDefinitions(XmlWebApplicationContext.java:123) Thanks, Rahul.

  Read the article

< Previous Page | 18 19 20 21 22 23 24 25 26 27 28 29  | Next Page >