Search Results

Search found 1134 results on 46 pages for 'cisco'.

Page 22/46 | < Previous Page | 18 19 20 21 22 23 24 25 26 27 28 29  | Next Page >

• Have to reset wireless frequently on iPad / Macs connected to Cisco WRV200

  - by retailevolved

  I have a Cisco WRV200 set up in our small office. The wireless signal works great for PCs, but I have found that Macs and iPads have to frequently reset the connection. It will be working for about 10 minutes, then stop. To fix it, I just turn off Airport and turn it on again. On an iPad, I have to go into settings, shut the wireless off, and then turn it on again. The router is broadcasting mixed B/G on channel 6. Security is WPA-PSK2. Anybody out there had similar issues with their router? How can I fix it?

  Read the article

• VMware - Broadcom 1000Gbps NIC does not link at 100Mbps to a Cisco switch port

  - by Spirit

  Today we've stumbled on a very awkward situation with our VMWare Server. The server is with ESX 3.5 that has a 1Gbps NIC. We bought a brand new managed Cisco Linksys switch with 10/100Mbps interface ports but when we plugged the cable in one of the ports the link simply does not wanted to activate :S... Does anyone with more VMware experience have ever had similar problem? From what I know is that 1Gbps NICs are backwards compatible with 100Mbps switches. This is what we've tryed so far but with no success: Tryed: http://kb.vmware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalId=1004089 Tryed to modify the /etc/modules.conf folowing the guide from this article http://kb.vmware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalId=813 After the changes I have restarted the networking services using # service network restart, # service mgmt-vmware restart and # service vmware-vpxa restart It seems that no matter how many times, or whatever approach/method (GUI or Shell) we try to change the speed and duplex of the network adapter and to force it to 100mbps it only accepts 1Gbps .. I am starting to go nuts :@

  Read the article

• Tunnel is up but cannot ping directly connected network

  - by drmanalo

  We configured a site-to-site VPN and here is the topology. I control the network on the left but not the one on the right. All devices in our network has public IPs. Server---ASA5505---Cisco887======Internet=====ASA5510---devices I can see the tunnel is up and can do extended ping using a loopback interface. From the 10.175 and 10.165 networks, they can also ping my loopback address. I can also dial in using a Cisco VPN client, and can connect to the devices on the right. #show crypto session Crypto session current status Interface: Vlan3 Profile: xxx-profile Session status: UP-ACTIVE Peer: 213.121.x.x port 500 IKEv1 SA: local 77.245.x.x/500 remote 213.121.x.x/500 Active IPSEC FLOW: permit ip 10.0.20.0/255.255.255.240 10.175.0.0/255.255.128.0 Active SAs: 0, origin: crypto map IPSEC FLOW: permit ip 10.0.20.0/255.255.255.240 10.165.0.0/255.255.192.0 Active SAs: 2, origin: crypto map #ping 10.165.29.39 source loopback 2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.165.29.39, timeout is 2 seconds: Packet sent with a source address of 10.0.20.1 !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 16/17/20 ms My problem is the devices on the right cannot reach my server. They could only ping the loopback address and nothing else. I'm pasting some diagnostics related to routing thinking perhaps routing is my issue. I can paste all the running-config on my side of network if needed. #show ip int brief Interface IP-Address OK? Method Status Protocol ATM0 unassigned YES NVRAM administratively down down Ethernet0 unassigned YES NVRAM administratively down down FastEthernet0 unassigned YES unset up up connected to ASA FastEthernet1 unassigned YES unset administratively down down FastEthernet2 unassigned YES unset administratively down down FastEthernet3 unassigned YES unset up up Loopback1 10.0.20.65 YES NVRAM up up Loopback2 10.0.20.1 YES NVRAM up up Virtual-Template1 77.245.x.x YES unset up down Virtual-Template2 77.245.x.x YES unset up down Vlan1 unassigned YES unset down down Vlan3 77.245.x.x YES NVRAM up up connected to the Internet #show run | section ip route ip route 0.0.0.0 0.0.0.0 77.245.x.x ip route 213.121.240.36 255.255.255.255 Vlan3 #show access-list Extended IP access list 102 10 permit ip 10.0.20.0 0.0.0.15 10.175.0.0 0.0.127.255 (3332 matches) 20 permit ip 10.0.20.0 0.0.0.15 10.165.0.0 0.0.63.255 (3498 matches) #show vlan-switch VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active 3 VLAN0003 active Fa0, Fa1, Fa2, Fa3 1002 fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup #show ip route Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route, H - NHRP, l - LISP + - replicated route, % - next hop override Gateway of last resort is 77.245.x.x to network 0.0.0.0 S* 0.0.0.0/0 [1/0] via 77.245.x.x 10.0.0.0/8 is variably subnetted, 5 subnets, 3 masks C 10.0.20.0/28 is directly connected, Loopback2 L 10.0.20.1/32 is directly connected, Loopback2 C 10.0.20.64/28 is directly connected, Loopback1 L 10.0.20.65/32 is directly connected, Loopback1 S 10.165.0.0/18 [1/0] via 213.121.x.x 77.0.0.0/8 is variably subnetted, 3 subnets, 3 masks S 77.0.0.0/8 [1/0] via 77.245.x.x C 77.245.x.x/29 is directly connected, Vlan3 L 77.245.x.x/32 is directly connected, Vlan3 213.121.x.0/32 is subnetted, 1 subnets S 213.121.x.x is directly connected, Vlan3 I read some of the posts here which lead to NATing issue but I'not sure of my next step. Should I translate my public address to private and route it to the loopback address? (only guessing) CISCO VPN site to site Site-to-Site VPN between two ASA 5505s only working in one direction Hope someone could help. Thanks in advance!

  Read the article

• MPLS basic configuration

  - by Vineet Menon

  I want to test out MPLS VPN in my lab. I have 3 routers. 2 PEs and 1P router, all cisco 2921. Something like this, ----- ---- ----- | PE1 |.1____192.168.1.0____.2| P |.2____192.168.2.0____.1| PE2 | | | | | | | ----- ---- ----- lo0:10.1.1.1 lo0:10.1.1.2 lo0:10.1.1.3 Here's the configuration file for each of them, PE1 router hostname PE1 ! no ipv6 cef ip source-route ip cef ! ! ! ip vrf cust1 rd 100:100 route-target export 100:100 route-target import 100:100 ! ! interface Loopback0 ip address 10.1.1.1 255.255.255.255 ! interface GigabitEthernet0/0 ip address 192.168.1.1 255.255.255.0 duplex auto speed auto ! interface GigabitEthernet0/1 ip vrf forwarding cust1 ip address 172.16.1.1 255.255.255.0 duplex auto speed auto ! router ospf 1 network 10.1.1.1 0.0.0.0 area 0 network 192.168.1.0 0.0.0.255 area 0 ! router bgp 100 bgp log-neighbor-changes neighbor 10.1.1.3 remote-as 100 neighbor 10.1.1.3 update-source Loopback0 neighbor 172.16.1.2 remote-as 65001 ! address-family vpnv4 neighbor 10.1.1.3 activate neighbor 10.1.1.3 send-community extended exit-address-family For P router: hostname P ! no ipv6 cef ip source-route ip cef ! interface Loopback0 ip address 10.1.1.2 255.255.255.255 ! interface GigabitEthernet0/1 ip address 192.168.1.2 255.255.255.0 duplex auto speed auto ! interface GigabitEthernet0/2 ip address 192.168.2.2 255.255.255.0 duplex auto speed auto ! router ospf 1 network 10.1.1.2 0.0.0.0 area 0 network 192.168.1.0 0.0.0.255 area 0 network 192.168.2.0 0.0.0.255 area 0 ! For PE2 router: ! hostname PE2 ! no ipv6 cef ip source-route ip cef ! ! ! ip vrf cust1 rd 100:100 route-target export 100:100 route-target import 100:100 ! ! ! interface Loopback0 ip address 10.1.1.3 255.255.255.0 ! interface GigabitEthernet0/0 ip address 192.168.2.1 255.255.255.0 duplex auto speed auto ! interface GigabitEthernet0/1 ip vrf forwarding cust1 ip address 172.16.2.1 255.255.255.0 duplex auto speed auto ! router ospf 1 network 10.1.1.3 0.0.0.0 area 0 network 192.168.2.0 0.0.0.255 area 0 ! router bgp 100 bgp log-neighbor-changes neighbor 10.1.1.1 remote-as 100 neighbor 10.1.1.1 update-source Loopback0 neighbor 172.16.2.2 remote-as 65001 ! address-family vpnv4 neighbor 10.1.1.1 activate neighbor 10.1.1.1 send-community extended exit-address-family ! I am following this article form cisco. But things are not working properly. Any help would be appreciated.

  Read the article

• Configuring a PIX 506e for Asterisk

  - by orthogonal3

  Hi all! I'm having problems configuring a old Cisco PIX running 6.3 and wondered if anyone can lend a hand? Simply put I have a PIX 506e that I want to put in my VoIP data path. I can't update it and getting a compat version of Java for that version of PIX is tough so I can't log onto the web interface. The PIX straddles two networks..... 192.168.5.0 on the inside, ...50.0 on the outside both net masks are 255.255.255.0 I have a local Asterisk server cluster with a single service IP (<local asterisk>) SIP is on UDP 5060 and RTP (for the voip data) is on UDP 18000-18999 I know thats a big range but hey may as well. I need the 192.168.5.0 net to have web and ftp access for updates and the like. DHCP, DNS and NTP is already provided on that network so I don't need external DNS access. So I think I want the following rules: SIP or RTP from <my itsp> arriving at <outside voip ip> NATed to <local asterisk> SIP or RTP able to do the reverse route (should be covered by high sec - low sec??) HTTP and FTP access outbound for software update for the servers etc I have the following config at the minute - and I think I'm almost there (I hope)... interface ethernet0 auto interface ethernet1 auto nameif ethernet0 outside security0 nameif ethernet1 inside security100 enable password wouldyouliketobeapeppertoo encrypted passwd wouldyouliketobeapeppertoo encrypted hostname afirewall domain-name adomain fixup protocol dns maximum-length 512 fixup protocol ftp 21 fixup protocol h323 h225 1720 fixup protocol h323 ras 1718-1719 fixup protocol http 80 fixup protocol rsh 514 fixup protocol rtsp 554 fixup protocol sip 5060 fixup protocol sip udp 5060 fixup protocol skinny 2000 fixup protocol smtp 25 fixup protocol sqlnet 1521 fixup protocol tftp 69 access-list acl_ping permit icmp any any access-list voip permit ip host <my itsp> host <local asterisk> mtu outside 1500 mtu inside 1500 ip address outside <outside pix ip> 255.255.255.0 ip address inside <inside pix ip> 255.255.255.0 arp timeout 14400 global (outside) 1 <outside generic ip> nat (inside) 1 192.168.5.0 255.255.255.0 0 0 static (inside,outside) <outside voip ip> <local asterisk> netmask 255.255.255.255 0 0 static (outside,inside) <local asterisk> <outside voip ip> netmask 255.255.255.255 0 0 access-group acl_ping in interface outside access-group acl_ping in interface inside route outside 0.0.0.0 0.0.0.0 <my next hop router> 1 route outside <my itsp> 255.255.255.255 <my next hop router> 1 I think I just need a hand with the access-lists and NAT/static rules. Would anyone be able to help as I've RTFM'd the Cisco docs a few times and they're heavy. Wishing I'd completed my CCNA now! Thanks all for any help, Phil

  Read the article

• I don't get any Internet when I connect connect Cisco DPC3825 DOCSIS 3.0 Gateway with DLink DIR-625 [on hold]

  - by Asif Akhtar

  I am using Cisco DPC3825 DOCSIS 3.0 Gateway as my modem and router right now and it works fine on a computer directly connected to Cisco DPC3825 DOCSIS 3.0 Gateway with wire but I am getting very low/poor signal strength on my wireless computer due to which I am looking to install DLink DIR-625 as my router but because when I connect Cisco DPC3825 DOCSIS 3.0 Gateway with DLink DIR-625 and connect my computer with wire to DIR-625 then I don’t get any Internet.(I get Internet when I connect my computer with wire with Cisco DPC3825 DOCSIS 3.0 and I know there is nothing wrong with DLink DIR-625).

  Read the article

• Can we configure windows 2008 DHCP server to not ignore the broadcast falg of DHCP requests?

  - by Mathieu Pagé

  We have a Cisco WAP4410N access point that does not relay broadcast packets from the wired network to the wireless clients when the network is secured by WPA2. This cause problem with Windows server's DHCP server that respond to DHCP request by broadcasting it's OFFER instead of Unicasting it like it's asked by Windows (and Android and iOS) clients. When we had a Windows 2003 server we configured the server not to ignore the broadcast flag (following these instructions) and it solved the problem. Now we upgraded our servers to Windows 2008 servers and the problem is back. Unfortunately, it seems Windows server 2008 ignore the IgnoreBroadcastFlag parameter. Is there any other way to make sure that Windows Server 2008 respond to DHCP requests using Unicast instead of broadcast? mp

  Read the article

• Install VPN client issue

  - by Andrey

  I'm trying to install the Shrew VPN client. In the process of installation an error occurs: Error 0x800f0203: Couldn't install the network component. It occurs when the installer tries to execute C:\Program Files\ShrewSoft\VPN Client\netcfg.exe -add service vflt C:\Program Files\ShrewSoft\VPN Client\drivers\vfilter.inf Antivirus, firewall, etc are disabled and I'm running as an administrator. I've installed vfilter.inf manually, but it leads nowhere. I have a similar situation with the Cisco VPN client. I need a VPN client supports group authorization, and imports the settings from pcf format. Windows Vista 32-bit, Shrew client 2.1.5, also try 2.0.0 for 32-bit.

  Read the article

• Install VPN client problem

  - by Andrey

  I'm trying to install VPN client Shrew, in the process of installation an error occurs. Error 0x800f0203: Couldn't install the network component. It occurs when the installer tries to execute C:\Program Files\ShrewSoft\VPN Client\netcfg.exe -add service vflt C:\Program Files\ShrewSoft\VPN Client\drivers\vfilter.inf Anti-virus, firewall, etc. - are disabled. Run from administrator. Installing vfilter.inf in manual mode, but it's nowhere leads. A similar situation with the Cisco VPN client. Need a VPN client supports a group authorization, and import the settings from pcf format. I'll be glad to any advice!

  Read the article

• Hardware firewall vs VMWare firewall appliance

  - by Luke

  We have a debate in our office going on whether it's necessary to get a hardware firewall or set up a virtual one on our VMWare cluster. Our environment consists of 3 server nodes (16 cores w/ 64 GB RAM each) over 2x 1 GB switches w/ an iSCSI shared storage array. Assuming that we would be dedicating resources to the VMWare appliances, would we have any benefit of choosing a hardware firewall over a virtual one? If we choose to use a hardware firewall, how would a dedicated server firewall w/ something like ClearOS compare to a Cisco firewall?

  Read the article

• Cisco Spam Blocker, Iron Port, Lotus Domino, Integration Help

  - by NickToyota

  Hi serverfault universe, I work for a medium sized (roughly 200 user) company. We are attempting to intagrate our new Cisco Spam Video Blocker (ironport) device into our network so that it acts as an incoming filter then passes it off to our Lotus domino mail server. And also vise versa. The way our network is setup currently has an mx record pointing to our Domino mail SMTP incoming server which is currently setup to be an inbound gateway and filter (using symantec domino mail software). We want to replace the inbound gateway with the ironport. Our company has also invested in a pool of external IP addresses which I believe has been currently assigned to our web, email, servers. What would the proper course of action be to successfully integrate the device be? Mx record change? Replace the domino gateway completely with the ironport? We attempted to set the ironport device to the external IP of what our mx record is pointing to without much success. Any help on proper setup would be greatly appreciated.

  Read the article

• Poor home office network performance and cannot figure out where the issue is

  - by Jeff Willener

  This is the most bizarre issue. I have worked with small to mid size networks for quite a long time and can say I'm comfortable connecting hardware. Where you will start to lose me is with managed switches and firewalls. To start, let me describe my network (sigh, shouldn't but I MUST solve this). 1) Comcast Cable Internet 2) Motorola SURFboard eXtreme Cable Modem. a) Model: SB6120 b) DOCSIS 3.0 and 2.0 support c) IPv4 and IPv6 support 3-A) Cisco Small Business RV220W Wireless N Firewall a) Latest firmware b) Model: RV220W-A-K9-NA c) WAN Port to Modem (2) d) vlan 1: work e) vlan 2: everything else. 3-B) D-Link DIR-615 Draft 802.11 N Wireless Router a) Latest firmware b) WAN Port to Modem (2) 4) Servers connected directly to firewall a) If firewall 3-A, then vlan 1 b) CAT5e patch cables c) Dell PowerEdge 1400SC w/ 10/100 integrated NIC (Domain Controller, DNS, former DHCP) d) Dell PowerEdge 400SC w/ 10/100/1000 integrated NIC (VMWare Server) 4) Linksys EZXS88W unmanaged Workgroup 10/100 Switch a) If firewall 3-A, then vlan 2 b) 25' CAT5e patch cable to firewall (3-A or 3-B) c) Connects xBox 360, Blu-Ray player, PC at TV 5) Office equipment connected directly to firewall a) If firewall 3-A, then vlan 1 b) ~80' CAT6 or CAT5e patch cable to firewall (3-A or 3-B) c) Connects 1) Dell Latitude laptop 10/100/1000 2) Dell Inspiron laptop 10/100 3) Dell Workstation 10/100/1000 (Pristine host, VMWare Workstation 7.x with many bridged VM's) 4) Brother Laser Printer 10/100 5) Epson All-In-One Workforce 310 10/100 5-A) NetGear FS116 unmanaged 10/100 switch a) I've had this switch for a long time and never had issues. 5-B) NetGear GS108 unmanaged 10/100/1000 switch a) Bought new for this issue and returned. 5-C) Linksys SE2500 unmanaged 10/100/1000 switch a) Bought new for this issue and returned. 5-D) TP-Link TL-SG10008D unmanaged 10/100/1000 a) Bought new for this issue and still have. 6) VLan 1 Wireless Connections (on same subnet if 3-B) a) Any of those at 5c b) HP Laptop 7) VLan 2 Wireless Connection (on same subnet if 3-B) a) IPad, IPod b) Compaq Laptop c) Epson Wireless Printer Shew, without hosting a diagram I hope that paints a good picture. The Issue The breakdown here is at item 5. No matter what I do I cannot have a switch at 5 and have to run everything wireless regardless of router. Issues related to using a switch (point 5 above) SpeedTest is good. Poor throughput to other devices if can communicate at all. Usually cannot ping other devices even on the same switch although, when able, ping times are good. Eventual lose of connectivity and can "sometimes" be restored by unplugging everything for several days, not minutes or hours but we're talking a week if at all. Directly connect to computer gives good internet connection however throughput to other devices connected to firewall is at best horrible. Yet printing doesn't seem to be an issue as long as they are connected via wireless. I have to force the RV220W to 1000Mb on the respective port if using a Gig Switch Issues related to using wireless in place of a switch (point 5 above) Poor throughput to other devices if can communicate. SpeedTest is good. Bottom line Internet speeds are awesome. By the way, Comcast went WAY above and beyond to make sure it was not them. They rewired EVERYTHING which did solve internet drops. Computer to computer connections are garbage Cannot get switch at 5 to work, yet other at 4 has never had an issue. Direct connection, bypass switch, is good for DHCP and internet. DNS must be on server, not firewall. Cisco insists its my switches but as you can see I have used four and two different cables with the same result. My gut feeling is something is happening with routing. But I'm not smart enough to know that answer. I run a lot of VM's at 5-c-3, could that cause it? What's different compared to my previous house is I have introduced Gigabit hardware (firewall/switches/computers). Some of my computers might have IPv6 turned on if I haven't turned it off already. I'm truly at a loss and hope anyone has some crazy idea how to solve this. Bottom line, I need a switch in my office behind the firewall. I've changed everything. The real crux is I will find a working solution and, again, after days it will stop working. So this means I cannot isolate if its a computer since I have to use them. Oh and a solution is not throwing more money at this. I'm well into $1k already. Yah, lame.

  Read the article

• Is bonding mode=5 a solution against MAC flapping?

  - by Yuri

  There is two are interconnected Cisco WS-2950T. By the one GBIC port on first switch connected a first NIC of bonding interface, and by the one GBIC port on second switch connected a second NIC of bonding interface. Of course the both switches sees the bonding MAC-address only on one interface (eg it is GBIC on first switch) and all incoming traffic for bonding interface passes through this GBIC. But in "mode=5" all outgoing traffic are distributed between the all interfaces that make bond. In this case, the packets will be dropped from the second switch and anyway will going through the first switch? Or the division will be working?

  Read the article

• share one vpn connection through windows rras with other clients

  - by KTYP

  I'm having a Cisco VPN connection to access our branch office. Since several people using the VPN I'm planing to install the VPN client on one of our server and share it through RRAS to save the licenses (like site - to - site). I install RRAS on a windows 2008 R2 (svrw2k8r2) and made the static routes on client computers. I could able to ping to the VPN's IP on svrw2k8r2 server but they can't seems to connect to the servers in other branch through this setup. Below is my setup My Branch Server: svrw2k8r2 - Windows 2008 R2 IP: 192.168.40.100/24 VPN IP: 10.0.100.12/8 Clients Win7 IP: 192.168.40.101 - 110 / 24 Other Branch Servers IP:10.10.0.10-20/24

  Read the article

• Windows 7 remote desktop connection does not respond to mouse or keyboard

  - by Daniel Jette

  Pretty much every time I connect to my work PC from home (both running Windows 7), I can see the screen refresh and signs of life (clock changes, notifications pop up), but I cannot interact with the remote machine at all. Mouse and keyboard input are both ignored. If I repeatedly reconnect, I will eventually get a connection that works. I think either a setting on my host machine, VPN client or work network is configured wrong. My home PC is running Windows 7 Professional. My work PC is running Windows 7 Enterprise. My VPN client is Cisco AnyConnect. Is this a problem anyone else has run in to? Any suggestions for settings to tweak?

  Read the article

• Setting up Splunk/IronPort WSA

  - by Ciddan

  Hello everyone! I recently stumbled across Splunk 4 (by way of an advert on this very site...) and found that it had an "App" that's designed to work with Cisco IronPort WebSecurity and E-Mail Appliances! That's really awesome, because good IronPort reporting is something our IT-dept. is looking for. Anyways - I'm totally lost on how to configure this thing. I've googled like a mad-man to find a guide or such like - but I haven't found anything. Has anyone here set up IP / Splunk? Any tips/pointers? Regards, Mikael Selander

  Read the article

• Setting up Splunk/IronPort WSA

  - by Ciddan

  I recently stumbled across Splunk 4 (by way of an advert on this very site...) and found that it had an "App" that's designed to work with Cisco IronPort WebSecurity and E-Mail Appliances! That's really awesome, because good IronPort reporting is something our IT-dept. is looking for. Anyways - I'm totally lost on how to configure this thing. I've googled like a mad-man to find a guide or such like - but I haven't found anything. Has anyone here set up IP / Splunk? Any tips/pointers?

  Read the article

• Problem linking two Cisco routers with a static route

  - by Chris Kaczor

  I'm trying to link two Cisco routers with a static route and I haven't been able to get it working as expected. Here is the basic setup: Router 1 - WRV210 - 192.168.1.1 - connected to cable modem Router 2 - RV120W - 192.168.2.1 I already have several machines on Router 1 that are working and I want to setup Router 2 with a few other machines on the different subnet. Here is what I've configured: Connected the WAN port on Router 2 to a LAN port on Router 1 Configured Router 1 to give 192.168.1.2 to Router 2 via DHCP Configured Router 1 with a static route (192.168.2.0 mask 255.255.255.0) to 192.168.1.2 using the LAN & Wireless interface Disabled the firewall on Router 2 (since it is covered by Router 1) Configured Router 2 to "Router" mode instead of "NAT" mode Configured Router 2 with a static route (192.168.1.0 mask 255.255.255.0) to 192.168.1.1 using the WAN interface From the research I've done I think that should be enough but things aren't working exactly as expected: Router 2 can ping 192.168.1.1 and 192.168.1.101 (a machine on router 1) A machine on Router 2 can ping 192.168.1.1 and 192.168.1.101 (a machine on router 1) ping 192.168.1.1 and 192.168.1.101 (a machine on router 1) Router 1 can NOT ping 192.168.2.1 or 192.168.2.101 (a machine on router 2) A machine on Router 1 can NOT ping 192.168.2.1 or 192.168.2.101 (a machine on router 2) can NOT ping 192.168.2.1 or 192.168.2.101 (a machine on router 2) Router 1 and a machine on Router 1 can ping 192.168.1.2 (Router 2 itself) I'm confused as to why Router 1 cannot talk to the 192.168.2.0/255.255.255.0 subnet. Any help would be greatly appreciated.

  Read the article

• Bandwidth Control on our Internet Connection

  - by AlamedaDad

  Hi all, I have Covad dual/bonded T1 service in our office coming through a Cisco 1841 and then through a Sonicwall 3060Pro/Enhanced SW firewall. The problem I'm looking for some input on is how to limit the amount of bandwidth any single user/PC can user for downloading a file from the Internet. It's become an issue that when one person happens to download let's say an ~300MB file, normal internet access for the other employees slows to a crawl. I've seen through MRTG that in fact usage of the circuit jumps to the full 3mb for the duration of the download and then drops. Is it possible to control this? I'm not familiar with QOS or the like so I'm not sure. Any help on this would be appreciated. Thanks...Michael

  Read the article

• ASA 5510 Need to filter traffic log events to my iPhone

  - by drpcken

  For some reason I cannot update apps or download apps to any ios devices on my network (tried both iphone and ipads). When I'm at home on my own network everything works fine. This started about a week ago. I've configured my iphone with a static IP address and even used 4.2.2.2 as my dns to rule out that the issue is with my DNS Server. I'm looking at the SYSLOG in ASDM (Cisco ASA 5510) but Im not sure it is providing me enough info. It seems to be showing ACL blocks on my public ip address, but not individual client IP's, so I can't see whats going on. How can I setup a way to filter any incoming/outgoing traffic to my iPhone's static IP and try and troubleshoot this?

  Read the article

• Connecting a network drive only when the VPN is connected?

  - by leeand00

  I have a thumb drive that I want to be able to connect to the same place over the network at one location as it is locally. Sometimes I leave it at the other location, but usually if I'm going to back it up, I back it up locally for network traffic. Is there a way to automatically connect the thumb drive when I connect to the VPN? (Always to the same drive letter...and obviously skip connecting it if it's already plugged in locally and the VPN is connected...) I'm using a Cisco VPN Client 5.x

  Read the article

• How can I configure a Linksys EA4500 + usb printer for network printing (without connect cloud)

  - by Larry Kyrala

  The documentation and classic firmware (2.0.37) for Cisco's Linksys EA4500 is a bit sparse on setup details. It says I can connect a USB-printer, but then goes on to try to sell "Connect Cloud" remote management software. I don't want that. I just want to know how to set this up with the existing advanced firmware. Is it possible? AFAIK, to setup a IPP or LDP printer, there is usually some kind of queue configuration on the server (i.e. the ea4500 in this case), but I can't find it in the firmware. I also have been unable to find any existing protocols from win7 or mac osx. (windows network share, IPP/LDP etc.) I'm curious if I need to have the "Storage" accounts active and connect to my router either via the local IP or router name. There's a lot of unknowns here; it would help to know how this particular router actually works.

  Read the article

• Packet logging on PIX firewall

  - by georged.id.auindex.htm

  We have a Cisco PIX 515 firewall and I would like to set up a simple logging that would give us a traffic breakdown for billing by: source destination protocol port size time PIX is plugged into Catalyst 2970 and I was told that the best thing since sliced bread for logging is to get Netflow and get Catalyst to log. My concern, however, (besides the Netflow cost) is that I really don't want to "listen" to the internal noise and all I'm interested in are the external traffic stats above for billing and analysis purposes. What would be the simplest and the easiest solution? Cheers George

  Read the article

• Trying to understand why VLANs need to be created on intermediate switches

  - by Jon Reeves

  I'm currently studying for the Cisco switching exam and having trouble understanding exactly how 802.1q tagging works. Given three daisy chained switches (A,B, and C) with trunk ports between them and VLAN 101 defined on both end switches (A and C), I'm not sure why the VLAN also needs to be defined on the middle one (B)? Note that I am not disputing that it does need to be configured, I'm just trying to understand why exactly. As I understand it, traffic from VLAN 101 on switch A will be tagged as it goes through the trunk to switch B. According to the documentation I have read, trunks will pass all VLANs by default, and the .1q tag is only removed when the frame leaves through an access port on the relevant VLAN. From this I would expect switch B to simply forward the tagged frame unchanged through the trunk to switch C. Can anyone shed some light on how switch B processes this frame and why it does not get forwarded through the other trunk ?

  Read the article

• Need to setup a RADIUS server to authenticate a Windows client to a Windows server

  - by drosenblatt

  I have a server that I have technicians who need to be able to access using shared credentials. However, doing that violates our security policy (!). I need each user to be able to authenticate using their own credentials, but the server in question has to be logged in with a certain login (these two requirements are clearly diametrically opposed). I thought that this would be a great application for a RADIUS server. I know how to setup RADIUS to go from Windows -- Cisco, but I have no idea how to use RADIUS to authenticate Windows -- Windows. Can this be done? If so, how?

  Read the article

< Previous Page | 18 19 20 21 22 23 24 25 26 27 28 29  | Next Page >