Search Results

Search found 772 results on 31 pages for 'opposite of you'.

Page 22/31 | < Previous Page | 18 19 20 21 22 23 24 25 26 27 28 29  | Next Page >

• pfSense router on a LAN with two gateways

  - by JohnCC

  I have a LAN with an ADSL modem/router on it. We have just gained an alternative high-speed internet connection at our location, and I want to connect the LAN to it, eventually dropping the ADSL. I've chosen to use a small PFSense box to connect the LAN to the new WAN connection. Two servers on the LAN run services accessible to the outside via NAT using the single ADSL WAN IP. We have DNS records which point to this IP. I want to do the same via the new connection, using the WAN IP there. That connection permits multiple IPs, so I have configured pfSense using virtual IP's, 1:1 NAT and appropriate firewall rules. When I change the servers' default gateway settings to the pfSense box, I can access the services via the new WAN IPs without a problem. However, I can no longer access them via the old WAN IP. If I set the servers' default gateway back to the ADSL router, then the opposite is true - I can access the services via the ADSL IP, but not via the new one. In the first case, I believe this is because an incoming SYN packet arrives at the ADSL WAN IP, and is NAT'd and sent to the internal IP of the server. The server responds with a SYN/ACK which it sends via its default gateway, the pfSense box. The pfSense box sees a SYN/ACK that it saw no SYN for and drops the packet. Is there any sensible way around this? I would like the services to be accessible via both IPs for a short period at least, since once I change the DNS it will take a while before everyone picks up the new address.

  Read the article

• Best shortcut in Total Commander

  - by life-warrior

  So, what's your favourite TC shortcut or shortcut combination ? Which one do you use and for what purpose ? Among my most often used: Ctrl-Left ( or Ctrl-Right ) - open archive or folder under cursor in opposite tab. Ctrl-Shift-Enter, Alt-F8, Ctrl-X - copy full file path to clipboard. Shift-F6, Shift-End(if needed), Ctrl-C - copy only file name w/o path. Select files, Ctrl-M - multi-rename, for example remove "DVDrip" from file names. Ctrl-\ - go to root directory. Ctrl-D, - go to directory with highlighted letter specified. For example, name a downloads directory "&Downloads" in favourites, and the letter after ampersand will be highlighted. Alt-F7, feed to listbox, Ctrl-A, Mark(menu)-Save selection to file - creates a file with all files and directories inside current, with full path. Ctrl-[3-6] - sort files by name(3), extension(4), date(5), size(6). For example, Sort by name, when you need movies and soundracks with the same name and different extension to group them together. Sort by extension, when you need to find EXEs in Windows directory. Sort by Date, when you need to find the latest file downloaded in your dir. Sort by size, when you need to delete the largest files for free space.

  Read the article

• Getting Dell E6320 with I7 to work with 3 monitors at 1920x1080p x 3

  - by MadBoy

  I want to buy Dell E6320 which comes with Intel Core I7-2620M (2.70GHz, 4MB cache, Dual Core) with Intel HD Graphics 3000. Laptop will come with docking station. I want to connect 3 monitors to that docking station so that working at home would give me some additional boost. Docking station will allow me to connect only 2 monitors so I'm looking at following other options: Matrox TRIPLEHEAD2GO DIGITAL Edition or TRIPLEHEAD2GO DP Edition. But reading Matrox Support Page intel GPU can't run the highest resolution with 3 monitors connected, it even gets worse since it seems monitors would have to be able to work at 50hz. Also I'm not sure but it seems that Matrox doesn't split the monitors as 3 separate monitors but simply as one big space (which is a bit opposite to what I need) Buy 2 or maybe just 1 USB based monitor but it would also mean having 1 or 2 different monitors then the main one, unless I buy 3 USB based monitors which would mean more money to spend. Also I found only couple of models and most of them require USB 3.0 and no other cables to plug in (nice but costly - couldn't find decent monitor with only USB for sending signal and having power connected normally) . But docking station has only one USB 3.0 port. Can I use hub and still get it to work? Find some converters from Digital to USB (I think DisplayLink does some?) Buy different laptop but what kind? I need it to be I7, small (13"), fast and lightweight. At same time it requires docking station that I can use at home to connect 3 external monitors. Some other suggested solution... Edit: I need 3 monitors for work in terms of coding in Visual Studio or having word/excel/outlook open. Nothing fancy. Maybe some movie once in a while.

  Read the article

• replacing buffalo lonkstations with FreeNAS, overall backup strategy, am I on the right path?

  - by Shreko

  We've been using 2 Buffalo LinkStations of 320Gb each for shared directory and employee's server storage (around 20 employees). So only documents (word, excel, cad drawings etc.) and database backup of the main application server (ERP, Accounting) 1 buffalo box serves as a main one, located at the server room, next to the main application server and the other buffalo box is located on the opposite side of the building (for fire protection) in a secure storage room and backs up the first one. We also have several external HDs that backs up everything from the buffalo box for an offsite backup. After 3.5 years of using these, capacity is a main limitation, I'm planning a replacement and would like to use FreeNAS (we already use monowall with great success). I would like to keep it simple and continue similar setup, building two low power boxes with 1 hd (2Tb) each. Is low power atom mobo OK? Not sure about HDs? I've read on this site somebody mentioning more seagate ES2 as more reliable and better performing. How would those eco/green drives compare. We've been pretty happy with speed of Buffalo boxes and I don't want my users to notice any slowdown. Any suggestion?

  Read the article

• Virtual Machine Network Services causes networking problems in Vista Enterprise 64 bit install

  - by Bill

  I have a Quad-core/8GB Vista Enterprise 64-bit (SP2) installation on which I installed Virtual PC 2007. I have a problem that is opposite of all that I found searching around the Internet--everybody has problems making network connections from their guest VM. When Virtual Machine Network Services is enabled in the protocol stack for my network card across a reboot, it causes access problems to the network. The amount of time to login in using a domain credentialed account is upwards of 3 minutes, then after reaching the desktop the network and sharing center shows that my connection to the domain is unauthenticated. Disabling and re-enabling the Virtual Machine Network Services (uncheck in network properties/apply/recheck/apply) fixes the problem. And as long as I have the VMNS disabled when I shutdown the restart runs smoothly. I just have to remember to enable after login and disable before shutdown. I have un-installed and re-installed Virtual PC 2007 multiple times with restarts between. The install consists of the SP1 + a KB patch for guest resolution fix. Any help would be greatly appreciated. Some additional information... At one point during my hairpulling and teethgnashing with this, I tried to ping my primary DC and observed some weird responses: (Our DC is 10.10.10.25, my dynamic IP was 10.10.10.203) Reply from 10.10.10.203, Destination host unreachable. Request timed out. Reply from 10.10.10.25: ... This is not consistently repeatable, but thought it might strike a chord with someone.

  Read the article

• Alfa AWUSO36H 1W dysfunctional driver

  - by BrainStorm

  I recently purchased an Alfa AWUSO36H 1W wireless USB adapter for my notebook, in order to improve signal strength and quality. I'm currently using Linux Mint 11, and the it uses the RTL8187 driver for this adapter, I'm also using a 4dbi antenna, though I have others. The problem is that this adapter does exactly the opposite of what it should, actually my internal Broadcom BCM4313 adapter works way better than the alfa. Browsing is slow, some network applications don't even work, pings against Google.com on the internal adapter runs smooth, while in the alfa it gets like 25% packets lost or more! I'm less them 50 feet from my AP, the internal adapter gets 44/70 link quality, and the alfa gets around 60/70 (iwconfig output). Also the system always sets alfa power to 20dbm(100mw), then I have to do sudo iw set reg B0 to make it 30dbm(1000mw), but apparently no significant change. I've installed wireless-compat drivers, no change either. And worst of all, in Windows 7 it works way more smoothly for browsing, though I couldn't test it properly there. I hope its a driver problem, even if it's a pain to find/compile Linux drivers for a starter, I prefer it to a hardware problem where I would need to buy another adapter, since I have no money left (except for the cantenna pieces).

  Read the article

• How to run Fujitsu P27T-7 LED monitor in its not native resolution and have perfect fonts rendering

  - by Ilia Rostovtsev

  My problem is completely opposite to anything I could find as I need to run my monitor in its NOT native resolution and have perfect font rendering. I recently got myself Ultra HD 2560x1440 27 inch monitor (Fujitsu P27T-7 LED) and I have an issue with this. I would call it personal but I'm afraid it's not as few people already agreed with me. I do programming and the text on UHD is way to small for comfortable usage. I changed the resolution to regular Full HD (1920x1080), it became just right but the text is looking slightly blur now, in comparison to both its natural UHD resolution and/or to my old 23 inch NEC. I am pretty frustrated and not sure what to do and how to make fonts look just as sleek as they should? I can't work in UHD resolution (my vision is 100% perfect), simply if calculated, picture size with Ultra HD (2560x1440) on 27 inch is around 30% smaller than Full HD (1920x1080) on 23 inch. In order to have same font size, if compared with Full HD 23 inch, 27 inch Ultra HD monitor must be around 32 inches in size. If I set my new monitor to regular Full HD 1920x1080, then the fonts' size are just perfect but the quality is not as it's blurry? Could anyone please help me out with an advise of how to solve this problem? Spec: nVidia 560 Ti with DVI-D port on Fedora 20. EDIT 1: Changing fonts doesn't really help as everything else doesn't look the way it should. EDIT 2: The monitor is buzzing on 2560x1440 so badly in case there are lots of lines on the screen, like file listing. If I type ls /usr/bin it makes such nasty irritating sound. When resolution goes to 1920x1080 it's a bit better. Any idea why?

  Read the article

• Win 7 x64 explorer.exe stops responding on copy/paste

  - by Sourabh

  Few months ago I changed my Win7 orb using this software. But it changed only the explorer.exe in C:\Windows. To solve that, I copied explorer.exe from there to C:\Windows\system32 and C:\Windows\SysWOW64 (Probably a bad idea). Things were working fine until a few days ago, it started giving me problems while copying. Sometimes, when I copy/paste, It works fine but sometimes it stays on that dialog box which looks like it is doing pre-copying things like counting number of files/file size etc. But its not. It stays on that screen forever. Now if I try to close it, title changes to cancelling but rest stays the same. If I try to close it too many times, explorer.exe crashes. And its not related to file-size. It may crash for 4Mb file and work fine for 10Gb file but some other time, it'll do the opposite. Is there any way to reset my explorer.exe and Is this because of explorer.exe or something else PS: I forgot to take backup of explorer.exe. PS2: I didn't install any software or downloaded anything that could harm my computer. EDIT I tried System Restore and SFC /scannow but they didn't help.

  Read the article

• ConfigMgr 2012 - How to automatically make updates available to computers without forcing them to be installed?

  - by Massimo

  I'm using System Center Configuration Manager 2012 with the Software Update Point feature; however, in this environment patching has to be strictly manual, because server reboots need to be approved and scheduled by different people; thus, I need to use ConfigMgr's SUP like I would use a plain WSUS server with auto-approval but with manual installation. I created some Automatic Deployment Rules to automatically download and deploy critical updates, and to have an installation dealine of "as soon as possible"; but then, I've also configured those rules to not do anything when the deadline is reached, and to not perform system restarts even if needed (see image). Also, I've configured the device collection to where those rules deploy updates to not have any valid maintencance window. However, I'm experiencing quite the opposite as what I was expecting: as soon as the new updates are processed by the ADRs, they get automatically installed on all systems by the Software Center, and the computers are subsequently restarted. Why is this happening? Am I getting something wrong or is just ConfigMgr 2012 not behaving like it should?

  Read the article

• Simple electric DC question. Currency consumption

  - by Bobb

  Suppose you have DC power supply and a consumer connected to it (i.e. computer PSU and a hard drive). Suppose PSU which was supplied with the consumer has output 5V 1A. So I assume that the consumer should not consume more than 1A. Suppose the original PSU is broken now and I want to replace it with the one I have which is 5V 10A. My guess is that current is something which depends on the consumer. So if the consumer consumes normally 1A then it will not consume more than that even if it is connected to 10A PSU. In other word - am I right assuming that the consumer will not burn out being connected to a power supply with higher current output? P.S. my understanding is that voltage is something independent from the consumer. If you give it higher voltage it will burn (voltage is from PSU to the consumer). However current must be in opposite - consumer sucks as much current as it need not as much as PSU can provide (of course given that max PSU current is greater than the consumer needs)

  Read the article

• Outlook 2007 panes keep moving when changing resolution

  - by SilverbackNet

  This problem is really bugging one of our users ever since he got a larger monitor. Now that the monitor has a different resolution than his laptop, every time he unplugs it to go home, the three Outlook panes get all jumbled up. The navigation is huge, the list is shoved over, and the reading pane is almost smushed out of existence, the the opposite when he comes back in and the reading pane fills the screen. He's sick of adjusting it every day. He always runs it maximized, for maximum reading area. Keeping the application within a 1024x768 window wouldn't really be an option for him. Is there any way built into Outlook to automatically adjust pane sizes when the resolution changes? If not, is there a third-party app that can help, or a way to script the changes into the registry somehow? (I can do running the script whenever the screen state changes.) If this is fixed in 2010 I might be able to convince the other admin that this is a good enough reason to allow it (which will require a new beta version of our archiving software).

  Read the article

• Computer does not boot, often

  - by tam

  I've ran into a issue with my computer that it does no longer reach POST, but simply powers on for a fraction of a second and powers off. But this is not always, some times it boots just normally and it works as it should, no issues with not enough power or anything. But as soon as I turn it of, I can not turn it back on, but then again at some random point it just powers up again, and resumes normal operation. If I disconnect the 8pin ATX connector from the motherboard, it powers up, fans and disks spinning normally until I power it off again. So this problem only happens when ATX is connected, which seems odd, I normally always saw this kind of an error if ATX was not connected, but here it's the exact opposite. It also does not emit any sound on the buzzer, except the normal beep, when it powers up normally. I have already tried: Remove graphics card Remove one and/or all RAM sticks Disconnect everything non-essential, even hard drives Clear CMOS I have not yet tried to remove all components and tried to boot everything outside of the case, because I did not have the time to disassemble and bleed the water loop. However, I can confirm that nothing is stuck underneath the motherboard, not is any of those brass raisers touching the board where it should not. Specs: Gigabyte GA-970A-UD3 AMD FX6300 ATI HD7850 I think this should be enough for this issue.

  Read the article

• Why does my microwave kill the Wi-Fi?

  - by Ohlin

  Every time I start the microwave in the kitchen, our home Wi-Fi stops working and all devices lose connection with our router! The kitchen and the Wi-Fi router are in opposite ends of the apartment but devices are being used a little here and there. We've been annoyed by the instability of the Wi-Fi for some time and it wasn't until recently we realized it was correlated to microwave usage. After some testing with having the microwave on and off we could narrow down the problem to only occurring when the router is in b/g/n mode and uses a set channel. If I change to b/g mode or set channel to auto then there is no problem any more...but still! The router is a Zyxel P-661HNU ("802.11n Wireless ADSL2+ 4-port Security Gateway" with latest firmware) and the microwave is made by Neff with an effect of 1000W (if this information might be useful to anyone). There is an "internet connection" light on the router and it doesn't go out when the interruption occurs so I think this is only an internal Wi-Fi issue. Now to my questions: What parts of the Wi-Fi can possibly be affected by the microwave usage? Frequency? Disturbances in the electrical system? How can setting Auto on channels make a difference? I thought the different channels were just some kind of separation system within the same frequency spectrum? Could this be a sign that the microwave is malfunctioning and slowly roasting us all at home? Is there any need to be worried? Since we were able to find router settings that cooperate well with our microwave's demand for attention, this question is mainly out of curiosity. But as most people out there...I just can't help the fact that I need to know how it's possible :-)

  Read the article

• Why is it a bad idea to use a customer email as the from address

  - by Crab Bucket

  I've got an application that emails users once they have filled in a form. It uses a [email protected] as a from address. The customer wants it to use the email from the form as the from address which could be anything. I have been told that this is a bad idea due to spoofing/blacklisting and spam. I feel really vague about the exact reason about why this is a bad idea particularly as i've got to try to counsel the client out of this. Can someone explain to me why this is a bad idea. Interestingly the client has used a gmail account as the from address as a demo which not only works fine but has enabled the application to start sending emails (it wouldn't do it before with an email which was [email protected]). Erm - what is going on. I'm told one thing and the opposite works. Sorry - i know this is basic but I could find anything on a google search. Largely I think because I'm having trouble even framing the question. EDIT Thank you everyone - great answers. Interestingly the server sending the email and the mail box that it is going to are both behind the same firewall so the client says they are unconcerned about spam. Oh well.

  Read the article

• Simple electric DC question. Current consumption

  - by Bobb

  Suppose you have DC power supply and a consumer connected to it (i.e. computer PSU and a hard drive). Suppose PSU which was supplied with the consumer has output 5V 1A. So I assume that the consumer should not consume more than 1A. Suppose the original PSU is broken now and I want to replace it with the one I have which is 5V 10A. My guess is that current is something which depends on the consumer. So if the consumer consumes normally 1A then it will not consume more than that even if it is connected to 10A PSU. In other word - am I right assuming that the consumer will not burn out being connected to a power supply with higher current output? P.S. my understanding is that voltage is something independent from the consumer. If you give it higher voltage it will burn (voltage is from PSU to the consumer). However current must be in opposite - consumer sucks as much current as it need not as much as PSU can provide (of course given that max PSU current is greater than the consumer needs)

  Read the article

• Can't open shared drive after disconnecting vpn

  - by Matt McMinn

  I use a VPN to connect to my office network. On my local network I have another WinXP machine that shares a printer and a few shared folders. While I'm connected to my work VPN, I can access the shared printer and folders on the other machine just fine, and vice versa. Once I disconnect the VPN, I can't access the local machine any more, and the other machine can't access my machine. The network itself seems ok - I can ping the other machine, get to the internet, and get on to a web server shared by the other machine, but I can't get to the shared folders or printer. If I reconnect to the VPN, my access is restored. I'm guessing this is some sort of authentication thing, but I don't know what. Any ideas? Update This problem is bothering me again, so here's an update. Depending on when I first access the WinXP machine, I either have this problem, or the opposite problem. After a reboot, if I (for example) print, then connect to the VPN, I can't access the machine while on the VPN. If after a reboot I connect to the VPN, then print, I can't access the machine off the VPN. In both cases, if I enable/disable the VPN again, I can access the machine again. Thanks

  Read the article

• Stack Managed Switches over a distance

  - by Joel Coel

  We have several buildings with stacked switches, where the distance between the stacked units is considerable... separate floors, or at opposite ends of a hallway. They are 3Com switches that stack using cat6 cabling. These switches are coming up on 12 years old now, and as I look around at replacements it seems no one supports this scenario any more. Stacking switches want to use fiber links (it more for me to run and terminate the fiber stacking cables than to purchase the switch) or other custom cables that seem only intended to jump up to the next unit in a rack. What have others done to support stacking over a distance? I'm considering breaking up the stacked switches into separate managed entities and just bridging from the root switch in the buildings, but I'd really like to avoid that for what I hope are obvious reason. The closest thing I've found are from netgear that use hdmi cables for the stacking connection... I could try to support that by running an additional cat6 line and re-terminating both links into a single hdmi port, but I have concerns over that approach as well.

  Read the article

• proxy pass domain FROM default apache port 80 TO nginx on another port

  - by user10580

  Im still learning server things so hope the title is descriptive enough. Basically i have sub.domain.com that i want to run on nginx at port 8090. I want to leave apache alone and have it catch all default traffic at port 80. so i am trying something with a virtual name host to proxy pass to sub.domain.com:8090, nothing working yet and go no idea what the right syntax could be. any ideas? most of what i found was to pass TO apache FROM nginx, but i want to the do the opposite. LoadModule proxy_module modules/mod_proxy.so LoadModule proxy_http_module modules/mod_proxy_http.so <VirtualHost sub.domain.com:80> ProxyPreserveHost On ProxyRequests Off ServerName sub.domain.com DocumentRoot /home/app/public ServerAlias sub.domain.com proxyPass / http://appname:8090/ (also tried localhost and sub.domain.com) ProxyPassReverse / http://appname:8090/ </VirtualHost> when i do this i get [warn] module proxy_module is already loaded, skippin [warn] module proxy_http_module is already loaded, skipping [error] (EAI 2)Name or service not known: Could not resolve host name sub.domain.com -- ignoring! and yes, the app is working (i have it running on port 80 with another subdomain) and it works at sub.domain.com:8090

  Read the article

• wireless to wired internet

  - by Mark T

  My wife uses an old computer which doesn't really like having an internet connection via a USB wireless adapter. I've tried several, and none have been satisfactory. The connection gets dropped often and it is frustrating for her. A wireless card also had the same trouble. Repositioning the computer made no difference. (Two laptops, nearby, connect just fine and stay up, so it isn't the router.) However, the computer always worked well when I had an Ethernet cable connected to it. I know there is a box which will connect to my wireless network and provide an Ethernet cable connection. But the terminology used is so complex, I can't tell what it is I really need. In case that wasn't clear, here it is in different words: What I need is just the opposite of a wireless router. My wireless router takes my cable modem's Ethernet connection and makes it available to wireless clients. What I want is a box which is a wireless client to my wireless router and provides an Ethernet cable connection that I can connect to any device. I need to know the right name for a box with such capabilities. If you know of some inexpensive examples, that would also be helpful. I'm running a wireless G network with a Linksys Router.

  Read the article

• Nginx redirect all request that does not match a file to a php file

  - by cyrbil

  I'm trying to get all request to: http://mydomain.com/downloads/* redirect to http://mydomain.com/downloads/index.php except if the requested file exist in /downloads/ ex: http://mydomain.com/downloads = /downloads/index.php http://mydomain.com/downloads/unknowfile = /downloads/index.php http://mydomain.com/downloads/existingfile = /downloads/existingfile My current problem is I have either the redirection to php working but static files not served or the opposite. Here is my current vhost conf: (which redirect fine but static files are send to php and fail) server { listen 80; ## listen for ipv4; this line is default and implied server_name domain.com; root /data/www; index index.php index.html; location / { try_files $uri $uri/ /index.html; } error_page 404 /404.html; # redirect server error pages to the static page /50x.html error_page 500 502 503 504 /50x.html; location = /50x.html { root /usr/share/nginx/www; } location ^~ /downloads { fastcgi_pass unix:/var/run/php5-fpm.sock; fastcgi_split_path_info ^(.+\.php)(/.+)$; fastcgi_index index.php; include fastcgi_params; try_files $uri @downloads; } location @downloads { rewrite ^ /downloads/index.php; } # pass the PHP scripts to FastCGI server # location ~ \.php$ { try_files $uri =404; fastcgi_split_path_info ^(.+\.php)(/.+)$; fastcgi_pass unix:/var/run/php5-fpm.sock; fastcgi_index index.php; include fastcgi_params; } } Precision: static files are symlinks created by /downloads/index.php Thank you for your help.

  Read the article

• DNAT from localhost (127.0.0.1)

  - by pts

  I'd like to set up a TCP DNAT from 127.0.0.1, port 4242 to 11.22.33.44, port 5353 on Linux 3.x (currently 3.2.52, but I can upgrade if needed). It looks like the simple DNAT rule setup doesn't work, telnet 127.0.0.1 4242 hangs for a minute in Trying 127.0.0.1..., and then it times out. Maybe it's because the kernel is discarding the returning packets (e.g. SYN+ACK), because it considers them Martian. I don't need an explanation why the simple solution doesn't work, I need a solution, even if it's complicated (e.g. it involves creating may rules). I could set up a usual DNAT from another local IP address, outside the 127.0.0.0/8 network, but now I need 127.0.0.1 as the destination address. I know that I can set up a user-level port forwarding process, but now I need a solution which can be set up using iptables and doesn't need helper processes. I was googling for this for an hour. It was asked multiple times, but I couldn't find any working solutions. Also there are many questions about DNAT to 127.0.0.1, but I don't need that, I need the opposite.

  Read the article

• How to stop split tunnelling over cisco VPN (OS X)?

  - by Notre

  I'm using OS X (Snow Leopard) and the built in Cisco IP Sec client to connect to my corporate VPN. Currently, everything works as designed, and desired for most people. However, I would like to be able to funnel all traffic (particularly all web browser traffic) through the VPN. (Note - I'm an end user here, not the network administrator). Is this possible? In searching around, most people are looking to do the opposite; break out the VPN and enable split tunnelling of data. I'd like to avoid the split tunnelling. Is there some setting I can make in my OS X client to make this happen? I ran across a post where routing table changes are made to force split tunnelling: how to force split tunnel routing on mac -> cisco vpn I'm thinking something similar to that might work, but I'm not a networking expert so I'm not sure where to start (or if it is even possible). Thank you! Notre

  Read the article

• Print over the internet from a remote linux session locally (on a Windows 7 machine) to the shared printers?

  - by obeliksz

  I'm trying to use a linux virtual machine as a file server for windows clients. I have successfully implemented remote file sharing (samba+ssh) with which I am able to print locally with a little program that I made for this purpose (jetforms style)... but I would like to hear about a somewhat more direct approach. How can I attach the printers to the server, so that I can for example open a file on the remote session and in the print dialogbox I would see my local printers (on the machine from which I have established a remote session)? I guess there should be some kind of putty tunneling, but dont know how. I have a windows 7 machine locally; there is a CentOS 6 VM over the internet. It has ssh, cups, and samba. I have found a question which asks the opposite: there is a windows based server to connect form linux but that windows has a domain, mine is just a simple windows workstation that is behind NAT and has a dynamic IP. That question is: Print from Linux to Windows networked printer.

  Read the article

• Windows user moving to Ubuntu 12.04. Where are the system tools, or equivalents?

  - by Big Endian

  I am a Windows user who has begun experimenting with Ubuntu. Ubuntu seems great, but for all the things it seems like I CAN'T do. How do I get to advanced administration stuff, like the list of drivers, all of the installed software, and something equivalent to Windows' Device Manager. I always heard that Linux was supposed to be very raw, and you had to have lots of computer experience to make it work. This seems just the opposite. Ubuntu seems very modern and user friendly, better in some regards than any operating system I have seen. Unfortunately, I can't find any of the guts of this system beneath all of the user friendly frosting... gunk... crap... stuff. I'm reminded more and more of an Apple computer (except Linux is more affordable :). So how do I peel back this layer and start using the computer? A solution other than installing Gnome 3 would be appreciated.

  Read the article

• WPF: Draw a grid on a Canvas?

  - by stefan.at.wpf

  Hello community, I'm currently trying to add gridlines to a canvas. I need an exact free space between them, where I'd like to place something for hit detection per cell, maybe simply a transparent border or such a thing. While I thought this would be an easy thing, I'm facing problems like antialiasing and that lines in WPF aren't very "calculate" / exact drawing friendly - e.g. if I draw a line on x=20 with a thickness of 10, the line's width goes from x=15 to x=25 (maybe not exactly, just some kind like that), so it takes the given position as middle point - if it would draw from 20 to 30 it would be easier in my case. Besides that making things more complex, how does WPF handle e.g. a thickness of 5? Draw thickness 3 left from the given point and the remaining 2 right from it? Or maybe just the opposite way? Well, just wanted to show you which problems I have, though this all maybe just seems simple to be done. Just wondering if anyone has ever done this before. Currently I find a Border without content and just 2 sites set to a thickness greater than 0 as line seems to work the best in my tests, seems like it's clear where they are drawn and they somehow don't seem to make any antialiasing problems. Just wondering if there's a more intuitive / better way of doing this? I don't want to lay a Canvas over a Grid, I think this maybe makes some things more complex in the end (by the way: how would I place a Canvas on top of a Grid?). Thanks for any hint!

  Read the article

< Previous Page | 18 19 20 21 22 23 24 25 26 27 28 29  | Next Page >