Search Results

Search found 8190 results on 328 pages for 'switch'.

Page 22/328 | < Previous Page | 18 19 20 21 22 23 24 25 26 27 28 29  | Next Page >

• KVM network bridge and public static IP for both host and guests

  - by Javier Martinez

  I have a Debian Server with 4 public static addresses. There is a KVM guest (also Debian) installed and running. What I want is to give the guest an IP of the host, so that both machines have public IPs. IP 1: 188.165.A.B IP 2: 178.33.CCC.D IP 3: 178.33.CCC.E IP 4: 178.33.CCC.F What should I do to have connection for host and guest ? This is network conf: # ifconfig br0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:188.165.A.B Bcast:188.165.255.255 Mask:255.255.255.0 inet6 addr: fe80::ea40:f2ff:fe0a:cc28/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3618 errors:0 dropped:4 overruns:0 frame:0 TX packets:4853 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:599562 (585.5 KiB) TX bytes:1693443 (1.6 MiB) eth0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet6 addr: fe80::ea40:f2ff:fe0a:cc28/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4274 errors:0 dropped:0 overruns:0 frame:0 TX packets:4879 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:720045 (703.1 KiB) TX bytes:1715641 (1.6 MiB) Interrupt:20 Memory:fe500000-fe520000 eth0:0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.D Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 eth0:1 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.E Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 eth0:2 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.F Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:27932 errors:0 dropped:0 overruns:0 frame:0 TX packets:27932 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1820862 (1.7 MiB) TX bytes:1820862 (1.7 MiB) vnet0 Link encap:Ethernet HWaddr fe:54:00:87:40:ec inet6 addr: fe80::fc54:ff:fe87:40ec/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:18 errors:0 dropped:0 overruns:0 frame:0 TX packets:204 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:1452 (1.4 KiB) TX bytes:16958 (16.5 KiB) #route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default aa.bb.cc.eu 0.0.0.0 UG 0 0 0 br0 188.165.255.0 * 255.255.255.0 U 0 0 0 br0 # brctl show bridge name bridge id STP enabled interfaces br0 8000.e840f20acc28 no eth0 vnet0 There is no firewall enabled and DNS is configured properly. What I want to achieve: | | | +----+-------------------------+-+------+ | | Host | | | | | | | | | | +------------+------+ | | eth0 | eth0:0-1 | | | 188.165.A.B | | | | | | | | | br0 vnet0 | | | +------------+------+ | | | | | | | | +------------+------+ | | | | | | | | eth0:2-+ | | | | 178.33.CCC.F | | | | | | | | Guest | | | +-------------------+ | +---------------------------------------+ Thanks you

  Read the article

• Find out which task is generating a lot of context switches on linux

  - by Gaks

  According to vmstat, my Linux server (2xCore2 Duo 2.5 GHz) is constantly doing around 20k context switches per second. # vmstat 3 procs -----------memory---------- ---swap-- -----io---- -system-- ----cpu---- r b swpd free buff cache si so bi bo in cs us sy id wa 2 0 7292 249472 82340 2291972 0 0 0 0 0 0 7 13 79 0 0 0 7292 251808 82344 2291968 0 0 0 184 24 20090 1 1 99 0 0 0 7292 251876 82344 2291968 0 0 0 83 17 20157 1 0 99 0 0 0 7292 251876 82344 2291968 0 0 0 73 12 20116 1 0 99 0 ... but uptime shows small load: load average: 0.01, 0.02, 0.01 and top doesn't show any process with high %CPU usage. How do I find out what exactly is generating those context switches? Which process/thread? I tried to analyze pidstat output: # pidstat -w 10 1 12:39:13 PID cswch/s nvcswch/s Command 12:39:23 1 0.20 0.00 init 12:39:23 4 0.20 0.00 ksoftirqd/0 12:39:23 7 1.60 0.00 events/0 12:39:23 8 1.50 0.00 events/1 12:39:23 89 0.50 0.00 kblockd/0 12:39:23 90 0.30 0.00 kblockd/1 12:39:23 995 0.40 0.00 kirqd 12:39:23 997 0.60 0.00 kjournald 12:39:23 1146 0.20 0.00 svscan 12:39:23 2162 5.00 0.00 kjournald 12:39:23 2526 0.20 2.00 postgres 12:39:23 2530 1.00 0.30 postgres 12:39:23 2534 5.00 3.20 postgres 12:39:23 2536 1.40 1.70 postgres 12:39:23 12061 10.59 0.90 postgres 12:39:23 14442 1.50 2.20 postgres 12:39:23 15416 0.20 0.00 monitor 12:39:23 17289 0.10 0.00 syslogd 12:39:23 21776 0.40 0.30 postgres 12:39:23 23638 0.10 0.00 screen 12:39:23 25153 1.00 0.00 sshd 12:39:23 25185 86.61 0.00 daemon1 12:39:23 25190 12.19 35.86 postgres 12:39:23 25295 2.00 0.00 screen 12:39:23 25743 9.99 0.00 daemon2 12:39:23 25747 1.10 3.00 postgres 12:39:23 26968 5.09 0.80 postgres 12:39:23 26969 5.00 0.00 postgres 12:39:23 26970 1.10 0.20 postgres 12:39:23 26971 17.98 1.80 postgres 12:39:23 27607 0.90 0.40 postgres 12:39:23 29338 4.30 0.00 screen 12:39:23 31247 4.10 23.58 postgres 12:39:23 31249 82.92 34.77 postgres 12:39:23 31484 0.20 0.00 pdflush 12:39:23 32097 0.10 0.00 pidstat Looks like some postgresql tasks are doing 10 context swiches per second, but it doesn't all sum up to 20k anyway. Any idea how to dig a little deeper for an answer?

  Read the article

• What's Switched LAN Topology ?

  - by mgpyone

  If somebody can tell me clearly what "Switched LAN Topology"is, it'll be great. I can't even understand what it's due to the following picture . Any answers are most welcome.

  Read the article

• Network Bridging for WiFi-to-Ethernet in linux

  - by shakaran

  It is possible Network Bridging for WiFi-to-Ethernet in linux instead of Ethernet-to-Ethernet? I have a CentOS 6.3 machine. I am using KVM and I want perform a brigde for virtualize more machines. This machine is connected only via wireless connection and it doesn't have a ethernet connection. So, I did a bridge over the WiFi interface like: # cat /etc/sysconfig/network-scripts/ifcfg-br0 DEVICE="br0" NM_CONTROLLED="yes" ONBOOT=yes TYPE=Bridge BOOTPROTO=none IPADDR=192.168.1.50 PREFIX=24 GATEWAY=192.168.1.1 DNS1=8.8.8.8 DNS2=8.8.4.4 DEFROUTE=yes IPV4_FAILURE_FATAL=yes IPV6INIT=no NAME="System br0" Then I edit my wireless conection like: # cat /etc/sysconfig/network-scripts/ifcfg-mywireless ESSID="mywireless" MODE=Managed KEY_MGMT=WPA-PSK WPA_ALLOW_WPA2=yes CIPHER_PAIRWISE=CCMP CIPHER_GROUP=CCMP TYPE=Wireless #BOOTPROTO=none #IPADDR=192.168.1.50 #PREFIX=24 #GATEWAY=192.168.1.1 #DNS1=8.8.8.8 #DNS2=8.8.4.4 DEFROUTE=yes IPV4_FAILURE_FATAL=yes IPV6INIT=no NAME="Auto mywireless" UUID=874***** ONBOOT=yes LAST_CONNECT=1355923469 BRIDGE=br0 After, I restart the network: # /etc/init.d/network restart Shutting down loopback interface: [ OK ] Bringing up loopback interface: [ OK ] Bringing up interface Auto_mywireless: Error: Unknown connection: 874***** [FAILED] Bringing up interface br0: [ OK ] But as you can see, it show a error. My ifconfig output shows now: # ifconfig br0 Link encap:Ethernet HWaddr 6E:20:AD:CE:D8:AB inet addr:192.168.1.50 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::6c20:adff:fece:d8ab/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:67 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:6393 (6.2 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:432 errors:0 dropped:0 overruns:0 frame:0 TX packets:432 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:62433 (60.9 KiB) TX bytes:62433 (60.9 KiB) ra0 Link encap:Ethernet HWaddr 00:22:F7:2B:87:E5 inet addr:192.168.1.42 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::222:f7ff:fe2b:87e5/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:46 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:487894880 (465.2 MiB) TX bytes:148136473 (141.2 MiB) virbr0 Link encap:Ethernet HWaddr 52:54:00:5B:30:9A inet addr:192.168.122.1 Bcast:192.168.122.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:70 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:5838 (5.7 KiB) But this doesn't give internet connection and I loss access to 192.168.1.50. So, it is possible setup this networking bridge WiFi-to-Ethernet?

  Read the article

• SSH login to Cisco switch using Rancid times out

  - by Lars

  I have a 3560 switch that I have configured to accept SSH logins, and this works fine. However I cannot get Rancid to complete the login process to any of my switches using SSH. I get a timeout error after a minute or so. Telnet logins work fine with the same username and password. Here is my rancid setup in .cloginrc: add user * {myuser} add password * {strongAccessPassword} {strongEnablePassword} add method * ssh telnet Then, when I run bin/clogin 10.10.1.10 I get: # bin/clogin 10.10.1.10 10.10.1.10 spawn ssh -c 3des -x -l myuser 10.10.1.10 ############################################### Please authenticate. ############################################### Password: Error: TIMEOUT reached Again, when I do this using telnet as my preferred mothod in .cloginrc, it works without issue.

  Read the article

• If fiber runs 1gig fine, are there any concerns when considering upgrading to 10gig transceivers?

  - by Eric

  We had fiber installed (connecting ~10 buildings) around 5 years ago and it has been working great. The initial setup involved Procurve 2848 and 2824 switches w/ 1gig transceivers. However, lately we have been considering upgrading our network both to increase bandwidth and possibly add VOIP. However, a lot of this is assuming that we can just use pop the existing fiber into 10gig XFP transceivers in better switches and call it a day. If the fiber works fine at 1G does that mean it should be fine for 10gig? If not, how can we confirm that our existing fiber trunks will work, preferably in an affordable fashion?

  Read the article

• How do you keep track of what's connected to your switches?

  - by Kamil Kisiel

  Currently we manually document the connections to the ports of our switches. Of course, maintenance is a chore, and the documentation is out of date as soon as you save it. Are there any tools for querying switches, preferably via SNMP, that can tell you what is connected on the other end? For the record, we use primarily HP ProCurve switches.

  Read the article

• Share Keyboard/Mouse between PC (windows?) and Android

  - by kashiko

  Has anyone come across software that can do this successfully/reliably? I would like to set up my Nexus 7 tablet on a stand under my monitor and use it with the mouse/KB hooked up to my desktop so I can continue to use it while using my desktop without having to pick it up. I was able to find one application which claims to do this (PC Loves Android), but reviews on the Google Play store do not seem to favor it.

  Read the article

• How to switch users without entering password

  - by torbengb

  I'm a newbie running Ubuntu 9.10. I have two users (wife and me), and each user's screensaver is set to lock so that on wakeup, we get to choose which user's desktop to go to. However, Ubuntu requires a password, so this is pretty tedious. I'd like to switch users without entering any password. I know about this trick that works for the boot login, but it doesn't deal with multiple users. Is it possible to set empty passwords for users in Ubuntu, or skip the password in other ways? (I'm expecting real Linux users to suggest that passwordless users must not get any rights and there be an admin user with a strong password. Yes, you're right. But that's not what this question is about. Thanks.)

  Read the article

• Abnormally high amount of Transmit discards reported by Solarwinds for multiple switches

  - by Jared

  I have several 3750X Cisco switches that, according to our Solarwinds NPM, are producing billions of transmit discards per day. I'm not sure why it's reporting these discards. Many of the ports on the 3750X's have 2960's connected to them and are hardcoded as trunk ports. Solarwinds NPM version 10.3 Cisco IOS version 12.2(58)SE2 Total output drops: 29139431: GigabitEthernet1/0/43 is up, line protocol is up (connected) Hardware is Gigabit Ethernet, address is XXXX (bia XXXX) Description: XXXX MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, media type is 10/100/1000BaseTX input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:47, output 00:00:50, output hang never Last clearing of "show interface" counters 1w4d Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 29139431 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 35000 bits/sec, 56 packets/sec 51376 packets input, 9967594 bytes, 0 no buffer Received 51376 broadcasts (51376 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 51376 multicast, 0 pause input 0 input packets with dribble condition detected 115672302 packets output, 8673778028 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 unknown protocol drops 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 pause output 0 output buffer failures, 0 output buffers swapped out sh controllers gigabitEthernet 1/0/43 utilization: Receive Bandwidth Percentage Utilization : 0 Transmit Bandwidth Percentage Utilization : 0

  Read the article

• Who moved this PC here aka Locate which port on switch a PC is plugged into

  - by ggonsalv

  The catch is you have no SNMP access, not even public. The end vision is locate a PC in building easily even if PC's are moved around. The MAC address of the PC is known and the software would run as client on each desktop, reporting back which port the PC was plugged into. Well from a programmer perspective, my network skills are not the best. Yes I could use SNMP, download the MAC port table, load it into SQL, match it to the PC name. Seems alot of work. Lets say I ping a single point from the PC. Would the echo have some thing unique for each device on the same switch? All I need to identify some thing unique for each PC plugged into each port. If the PC was moved from location A to a different location then the unique response would change.

  Read the article

• Force10 layer 3 switches

  - by ALQ

  We've been running Cisco and dell layer 3 switches. The former are expensive and reliable, the latter a lot cheaper and fraught with issues. Anyone has positive experience with the core Force10 switches (and edge switches as well)?

  Read the article

• IOGEAR KVM cannot reset admin account

  - by George Horlacher

  According to the manual you can do a cold reset by holding the reset button in for 3 seconds. This does seem to reset it but the username and password are not reset... I've tried the keyboard hotkeys - Num-Lock and minus sign (-) to get into hotkey mode and then use the "r" and "" to reset to factory defaults but that doesnt seem to do anything either. It just reverts to User1. I'm not sure what the default admin username should be but admin doesnt seem to work I need to get to the admin menu to name the ports but cannot get access. Any ideas? Using GCS1758 manual with no luck.

  Read the article

• Boot linux off hard drive and then switch to run from usb flash disk

  - by Jesse

  I have an older laptop that I want to use as a simple media server on my home network. I would like to avoid using the internal hard drive except for booting (BIOS does NOT support booting from USB). My thought was to mirror the hard drive (currently has current install of Arch Linux) onto the flash drive and then after booting switch over to run everything from the flash drive. I read the following article about using a RAM disk (HOW-TO: Boot OS into RAM for speed and silence) but ran into problem because the USB subsystem does not seem to be initialized soon enough (I create root and home paritions on the flash disk and modified fstab to pick those - didn't work). Any thoughts?

  Read the article

• How to switch off Outlook Synchronization Manager

  - by mr.nothing

  I have one strange thing which is happening to my outlook. It tries to synchronize something (seems it do this every time send/recieve triggers). Does anybody know how to switch this manager off? Here is the icon of the sync manager in the task bar (left one) https://www.sugarsync.com/pf/D9085558_69411843_95701 Thanks in advance! p.s. it's also annoying me that something gone wrong and sync failed. Also every time it tries to sync something internet explorer says me that there are too many temporary internet files and asking me to expand space for its storing. https://www.sugarsync.com/pf/D9085558_69411843_95781 Please, help! This makes me crazy.

  Read the article

• sniffing on a switched LAN

  - by shodanex

  Hi, I often find myself in the position of having to sniff on a connection between for example an arm board I am developing on, and another computer on the network, or out of the network. The easy situation is when I can install a sniffer on the computer talking to the embedded device. When it is not possible, I currently install an old 10Mb/s HUB. However I am afraid my HUB might stop working, and I would like to know some alternative. Here are the alternatives I could think of : Buy another HUB. Is that still possible ? Have some sort of ethernet sniffing bridge, like what they do for USB. I am afraid this kind of device is expensive. use ARP poisoning.

  Read the article

• Dell powerconnect 6224 vlan routing

  - by user1007727

  I have a small network and I need help with routing .. . My VLANs VLAN 1010 SALES VLAN 1020 HR I have assigned the above vlans to a tagged port and I have added a default route to send the traffic of to my firewall. ip route 0.0.0.0 0.0.0.0 10.10.10.10 I have added a new vlan VLAN 1030 Services and I would like its traffic to go to a different interface on the firewall, 10.10.10.20 how can I go about doing that? can someone give me an example? your help is highly appreciated. Thank you

  Read the article

• Using a KVM with a Sun Ultra 45

  - by Kit Peters

  I have a friend with two machines: a Mac and a Sun Ultra45. He wants to use a single monitor (connected via DVI) and USB keyboard / mouse with both machines. Try as I might, the Sun box will not bring up a console if the KVM is connected. However, if I connect a monitor, keyboard, and mouse directly to the Sun box, it will bring up a console that I can then (IIRC) connect to the KVM. Is there any way I can make the Sun box always bring up a console, regardless of whether it "sees" a monitor, keyboard, and mouse?

  Read the article

• switch's mgmt-ip is not remotely reachable.

  - by RainDoctor

  Switch model: Netgear FSM7352PS mgmt-ip: 192.168.1.100/24 Vlan id: 1 (default) There are couple of hosts in this Vlan: 192.168.1.2 (esxi console), for instance. 192.168.1.1 is the firewall/router interface. I can ping 192.168.1.1 and 192.168.1.2 from other vlans, say, 172.31.0.0/24 I can ssh to 192.168.1.2 from 172.31.0.0/24 I can't ping 192.168.1.100 from 172.31.0.0/24 However, I can ping 192.168.1.100 from 192.168.1.2 or from my laptop connected to that vlan (192.168.1.11). I can connect to the web GUI from my laptop when I am in that Vlan. Can anyone shed some light on why I am not able to connect from other vlans?

  Read the article

• Switch user from locked screensaver?

  - by desert69

  I'm having the same problem as this, but the answer from there doesn't work for me. Neither in my iMac upgraded from Lion to Mountain Lion (currently at 10.8), nor from a Mac Mini with Lion Server (10.7.4). I have "Show fast user switching menu as" enabled at "Users & Groups" Login Options, but when I have to login from screensaver, there's no option to switch user. How can I enable such an option? EDIT: I think I forgot to mention that we believe (just guessing) that it has to do with network accounts. We use network accounts here, and have that issue. My boss says he could solve this issue at his house's Mac, which don't use network accounts. Does it make a difference?

  Read the article

• kvm:vga driver vbempg cause blue screen in guest os Windows XP

  - by hellolwq

  I don't know if the problem was well know,I searched the google,but didn't get anything useful. I configed the KVM guest vga mode as vga std and got a yellow exclamation sign with the vga in the XP guest OS. so I found the vbempg.zip in the follow address: http://forum.ubuntu.org.cn/download/file.php?id=45928&sid=b394b9ca338fdca59a4174c5ee4dee26 Some often,I could get a blue screen crash.Any one could give some further information?

  Read the article

• Best Performing Remote Desktop Software for WAN

  - by Dave

  I've been tasked with connecting a computer in one of our branches in the midlands to one in south wales. We have been using windows remote desktop but find it too slow. The ADSL on the computer were connecting to is about 6Mb Download and 470Kb Upload so not majorly fast. That connection is also shared with about 10 other internet users. I'm trying to find out if the is any remote desktopn connecting software that performs better than the microsoft remote desktop software. Or, would i be better using a KVM over IP? I've looked into connecting the offices through BT's fiber optic but at £21k a year rental were trying to find a cheaper solution! Any help would be great. Thanks, Dave,

  Read the article

• My linux server "Number of processes created" and "Context switches" are growing incredibly fast

  - by Jorge Fuentes González

  I have a strange behaviour in my server :-/. Is a OpenVZ VPS (I think is OpenVZ, because /proc/user_beancounters exists and df -h returns /dev/simfs drive. Also ifconfig returns venet0). When I do cat /proc/stat, I can see how each second about 50-100 processes are created and happens about 800k-1200k context switches! All that info is with the server completely idle, no traffic nor programs running. Top shows 0 load average and 100% idle CPU. I've closed all non-needed services (httpd, mysqld, sendmail, nagios, named...) and the problem still happens. I do ps -ALf each second too and I don't see any changes, only a new ps process is created each time and the PID is just the same as before + 1, so new processes are not created, so I thought that process growing in cat /proc/stat must be threads (Yes, seems that processes in /proc/stat counts threads creation too as this states: http://webcache.googleusercontent.com/search?q=cache:8NLgzKEzHQQJ:www.linuxhowtos.org/System/procstat.htm&hl=es&tbo=d&gl=es&strip=1). I've changed to /proc dir and done cat [PID]\status with all PIDs listed with ls (Including kernel ones) and in any process voluntary_ctxt_switches nor nonvoluntary_ctxt_switches are growing at the same speed as cat /proc/stat does (just a few tens/second), Threads keeps the same also. I've done strace -p PID to all process too so I can see if any process is crating threads or something but the only process that has a bit of movement is ssh and that movement is read/write operations because of the data is sending to my terminal. After that, I've done vmstat -s and saw that forks is growing at the same speed processes in /proc/stat does. As http://linux.die.net/man/2/fork says, each fork() creates a new PID but my server PID is not growing! The last thing I can think of is that all process data that proc/stat and vmstat -s show is shared with all the other VPS stored in the same machine, but I don't know if that is correct... If someone can throw some light on this I would be really grateful.

  Read the article

• Can I uninstall Qmail when I switch to Gmail Apps

  - by Saif Bechan

  I am not going to run a mail server anymore on my system. I am going to switch to Gmail. Can I then just uninstall Qmail or my previous mail server programm. I want to be able to send email from PHP. And I also want to get the email that Logwatch sends me from within the system. Basically, to have your server send email do you need an email server? Or will Gmail cover all of this.

  Read the article

• Need help connecting to SRW2024 Linksys Switch from CentOS 5.4

  - by sxanness

  I am configured a Linksys SRW2024, I accidently changed the management VLAN before changing the VLAN configuration thus I can no longer access it with the net. The only way I have read to get into it now is via a console cable, my laptop with me is a MacBook Pro with no Serial port connection, apart from driving around a town that I am unfamilar with to find an adapter I thought I would try on a Linux box. I have a CentOS 5.4 server here (PowerEdge R300) that I am trying to use to talk to the switch. I tried minicom first but I do not see the console. Another site suggested the screen command. I tried "screen /dev/ttyS0 38400" but all I get is blinking curser, I do not see the configuration. I don't know if anyone here as any tips but I hope someone does. Thank You,

  Read the article

< Previous Page | 18 19 20 21 22 23 24 25 26 27 28 29  | Next Page >