Search Results

Search found 1123 results on 45 pages for 'wayne lo'.

Page 22/45 | < Previous Page | 18 19 20 21 22 23 24 25 26 27 28 29  | Next Page >

• Trouble connecting a Ubuntu system to IPv6 tunnel over NAT

  - by John Millikin

  I'm trying to set up an IPv6 tunnel, via Hurricane Electric's tunnel-broker service. I've configured my system using their example commands: # $ipv4a = tunnel server's IPv4 IP # $ipv4b = user's IPv4 IP # $ipv6a = tunnel server's side of point-to-point /64 allocation # $ipv6b = user's side of point-to-point /64 allocation ip tunnel add he-ipv6 mode sit remote $ipv4a local $ipv4b ttl 255 ip link set he-ipv6 up ip addr add $ipv6b dev he-ipv6 ip route add ::/0 dev he-ipv6 And have configured my desktop to be in my NAT router's DMZ. The router is running Tomato firmware. But I can't ping any IPv6 services: $ ping6 -I he-ipv6 '2001:470:1f04:454::1' PING 2001:470:1f04:454::1(2001:470:1f04:454::1) from 2001:470:1f04:454::2 he-ipv6: 56 data bytes From 2001:470:1f04:454::2 icmp_seq=1 Destination unreachable: Address unreachable From 2001:470:1f04:454::2 icmp_seq=2 Destination unreachable: Address unreachable I can ping my local address: $ ping6 -I he-ipv6 '2001:470:1f04:454::2' PING 2001:470:1f04:454::2(2001:470:1f04:454::2) from 2001:470:1f04:454::2 he-ipv6: 56 data bytes 64 bytes from 2001:470:1f04:454::2: icmp_seq=1 ttl=64 time=0.037 ms 64 bytes from 2001:470:1f04:454::2: icmp_seq=2 ttl=64 time=0.039 ms I don't know much about routing, but results I found online suggested the output of ip -6 route and ip addr could be useful: $ ip -6 route 2001:470:1f04:454::/64 via :: dev he-ipv6 proto kernel metric 256 mtu 1480 advmss 1420 hoplimit 4294967295 fe80::/64 dev virbr0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev eth1 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 via :: dev he-ipv6 proto kernel metric 256 mtu 1480 advmss 1420 hoplimit 4294967295 default dev he-ipv6 metric 1024 mtu 1480 advmss 1420 hoplimit 4294967295 $ ip addr 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 100 link/ether 00:1c:c0:a1:98:b2 brd ff:ff:ff:ff:ff:ff inet 192.168.1.10/24 brd 192.168.1.255 scope global eth1 inet6 fe80::21c:c0ff:fea1:98b2/64 scope link valid_lft forever preferred_lft forever 3: virbr0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN link/ether 36:4c:33:ab:0d:c6 brd ff:ff:ff:ff:ff:ff inet 192.168.122.1/24 brd 192.168.122.255 scope global virbr0 inet6 fe80::344c:33ff:feab:dc6/64 scope link valid_lft forever preferred_lft forever 4: vboxnet0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000 link/ether 00:76:62:6e:65:74 brd ff:ff:ff:ff:ff:ff 5: pan0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN link/ether 7e:29:5e:7c:ba:93 brd ff:ff:ff:ff:ff:ff 6: sit0: <NOARP> mtu 1480 qdisc noop state DOWN link/sit 0.0.0.0 brd 0.0.0.0 7: he-ipv6@NONE: <POINTOPOINT,NOARP,UP,LOWER_UP> mtu 1480 qdisc noqueue state UNKNOWN link/sit 24.130.225.239 peer 72.52.104.74 inet6 2001:470:1f04:454::2/64 scope global valid_lft forever preferred_lft forever inet6 fe80::1882:e1ef/128 scope link valid_lft forever preferred_lft forever

  Read the article

• Two network adapters on Ubuntu Server 9.10 - Can't have both working at once?

  - by Rob

  I'm trying to set up two network adapters in Ubuntu (server edition) 9.10. One for the public internet, the other a private LAN. During the install, I was asked to pick a primary network adapter (eth0 or eth1). I chose eth0, gave the installer the details listed below in the contents of /etc/network/interfaces, and carried on. I've been using this adapter with these setting for the last few days, and every thing's been fine. Today, I decide it's time to set up the local adapter. I edit the /etc/network/interfaces to add the details for eth1 (see below), and restart networking with sudo /etc/init.d/networking restart. After this, attempting to ping the machine using it's external IP address fails, but I can ping it's local IP address. If I bring eth1 down using sudo ifdown eth1, I can successfully ping the machine via it's external IP address again (but obviously not it's internal IP address). Bringing eth1 back up returns us to the original problem state: external IP not working, internal IP working. Here's my /etc/network/interfaces (I've removed the external IP information, but these settings are unchanged from when it worked) rob@rhea:~$ cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary (public) network interface auto eth0 iface eth0 inet static address xxx.xxx.xxx.xxx netmask xxx.xxx.xxx.xxx network xxx.xxx.xxx.xxx broadcast xxx.xxx.xxx.xxx gateway xxx.xxx.xxx.xxx # The secondary (private) network interface auto eth1 iface eth1 inet static address 192.168.99.4 netmask 255.255.255.0 network 192.168.99.0 broadcast 192.168.99.255 gateway 192.168.99.254 I then do this: rob@rhea:~$ sudo /etc/init.d/networking restart * Reconfiguring network interfaces... [ OK ] rob@rhea:~$ sudo ifup eth0 ifup: interface eth0 already configured rob@rhea:~$ sudo ifup eth1 ifup: interface eth1 already configured Then, from another machine: C:\Documents and Settings\Rob>ping [external ip] Pinging [external ip] with 32 bytes of data: Request timed out. Request timed out. Request timed out. Request timed out. Ping statistics for [external ip]: Packets: Sent = 4, Received = 0, Lost = 4 (100% loss), Back on the Ubuntu server in question: rob@rhea:~$ sudo ifdown eth1 ... and again on the other machine: C:\Documents and Settings\Rob>ping [external ip] Pinging [external ip] with 32 bytes of data: Reply from [external ip]: bytes=32 time<1ms TTL=63 Reply from [external ip]: bytes=32 time<1ms TTL=63 Reply from [external ip]: bytes=32 time<1ms TTL=63 Reply from [external ip]: bytes=32 time<1ms TTL=63 Ping statistics for [external ip]: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms So... what am I doing wrong?

  Read the article

• Confusion on networking service start/stop in Ubuntu

  - by Daniel Ball

  I'm preparing to move and took down two of my servers, leaving only one with some essential services running. What I neglected to consider was that one was the DHCP server(which I realized when somebody contacted me saying they couldn't connect. Whups). So because I only have a few hosts on this small network, I opted to just statically configure them for now. One of these is a new Ubuntu 11.04 server, where I have very little experience. I edited /etc/network/interfaces and /etc/hosts to reflect my changes. I ran $sudo /etc/init.d/networking stop *deconfiguring network interfaces ... So yay. Then I try to start, it gives me the mumbo jumbo about using services (why didn't it do that for the stop?) So instead I run ... $sudo service networking start networking stop/waiting Now, to me that says the status of the service is stopped. But when I ping another computer, I get a successful reply. So is it not actually stopped? More importantly, am I doing something wrong? Edit daniel@FOOBAR:~$ sudo service networking status networking stop/waiting daniel@FOOBAR:~$ sudo service networking stop stop: Unknown instance: daniel@FOOBAR:~$ sudo service networking status networking stop/waiting daniel@FOOBAR:~$ sudo service networking start networking stop/waiting daniel@FOOBAR:~$ sudo service networking status networking stop/waiting So you can see why I ran /etc/init.d/networking stop instead. For some reason upstart (that is what "services" is, right?) isn't working with stop. cat /etc/hosts 127.0.0.1 localhost 127.0.1.1 FOOBAR 198.3.9.2 FOOBAR #Added entry July 19 2011 # The following lines are desirable for IPv6 capable hosts ::1 ip6-localhost ip6-loopback fe00::0 ip6-localnet ff00::0 ip6-mcastprefix ff02::1 ip6-allnodes ff02::2 ip6-allrouters cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface #auto eth0 #iface eth0 inet dhcp # hostname FOOBAR auto eth0 iface eth0 inet static address 198.3.9.2 netmask 255.255.255.0 network 198.3.9.0 broadcast 198.3.9.255 gateway 198.3.9.15 No I didn't save backups, it was just a minor change so I just commented out the old DHCP setting. Edit I set everything back to original settings and set up a DHCP server. "starting" networking does the same thing. I can only assume this is normal, I just don't know WHY. It can't be anything to do with the configuration files, since they've been restored.

  Read the article

• Virtual Network Interface and NAT disables localhost access for MySQL and Apache

  - by Interarticle

  I'm running an Ubuntu Server 12.04, and recently I configured it to do NAT for my laptop. Since the server has only one NIC, I followed instructions online to create a virtual network device (eth0:0) that has a LAN IP address, then further configured iptables and UFW to allow internet sharing. However, just a few days ago, I discovered that one of the PHP pages hosted on the server failed for no apparent reason. A little digging revealed that the MySQL server started refusing connections from localhost. The same happened with a page (PhpMyAdmin) that was configured to be accessible only from localhost (in Apache2). The error, as shown by $mysql --protocol=tcp -u root -p looks like ERROR 1130 (HY000): Host '<host name of eth0>' is not allowed to connect to this MySQL server However, the funny thing is, I configured the mysql server to allow root access from localhost (only). Moreover, the mysql server listens only on 127.0.0.1:3306, as shown by: sudo netstat -npa | head Active Internet connections (servers and established) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 127.0.0.1:3306 0.0.0.0:* LISTEN 1029/mysqld which means that the connection could have only come from 127.0.0.1 (Note that MySQL is working because I can still connect to it via unix domain sockets) In effect, it seems that all tcp connections originating from 127.0.0.1 to 127.0.0.1 appear to any local daemon to come from the eth0 IP address. Indeed, apache2 allowed me to access PhpMyAdmin after I added allow <eth0 IP address>. The following are my network configurations (redacted): /etc/hosts: 127.0.0.1 localhost 211.x.x.x <host name of eth0> <server name> #IPv6 Defaults follows .... /etc/network/interfaces: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 211.x.x.x netmask 255.255.255.0 gateway 211.x.x.x dns-nameservers 8.8.8.8 # dns-* options are implemented by the resolvconf package, if installed dns-search xxxxxxx.com hwaddress ether xx:xx:xx:xx:xx:xx auto eth0:0 iface eth0:0 inet static address 192.168.57.254 netmask 255.255.254.0 broadcast 192.168.57.255 network 192.168.57.0 /etc/ufw/sysctl.conf: #Uncommented the following lines net/ipv4/ip_forward=1 net/ipv6/conf/default/forwarding=1 /etc/default/ufw: DEFAULT_FORWARD_POLICY="ACCEPT" #Changed DROP to ACCEPT /etc/init/internet-sharing.conf (upstart script I wrote), section pre-start script: iptables -A FORWARD -o eth0 -i eth0:0 -s 192.168.57.22 -m conntrack --ctstate NEW -j ACCEPT iptables -A FORWARD -m conntrack --ctstate ESTABLISHED,RELATED -j ACCEPT iptables -A POSTROUTING -t nat -j MASQUERADE Note again that my problem here is that programs cannot access localhost tcp services, from the server itself, and that access is blocked because the services have access control allowing only 127.0.0.1. I have no problem connecting (as in TCP connections) to services via tcp, even if the services listen only on 127.0.0.1. I do NOT want to connect to the services from another computer.

  Read the article

• Cliq Wireless questions

  - by Nathan Adams

  Heres the deal: I am by no means a Linux expert, even less when it comes to the Android OS but lets see if we can't solve this problem. The problem I am having is that on the Cliq we have a broadcom chip. In order to use the wireless card you must first insert the module into the kernel. Fine: # insmod /system/lib/dhd.ko insmod /system/lib/dhd.ko # lsmod lsmod dhd 164936 0 - Live 0xbf000000 # BUT netcfg (or ifconfig in busybox) does not recognize that there is a wireless adapter there: # netcfg netcfg lo UP 127.0.0.1 255.0.0.0 0x00000049 dummy0 DOWN 0.0.0.0 0.0.0.0 0x00000082 rmnet0 UP 14.67.164.2 255.255.255.252 0x00001043 rmnet1 DOWN 0.0.0.0 0.0.0.0 0x00001002 rmnet2 DOWN 0.0.0.0 0.0.0.0 0x00001002 usb0 DOWN 0.0.0.0 0.0.0.0 0x00001002 # busybox ifconfig busybox ifconfig lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:282 errors:0 dropped:0 overruns:0 frame:0 TX packets:282 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:18754 (18.3 KiB) TX bytes:18754 (18.3 KiB) rmnet0 Link encap:Ethernet HWaddr EE:83:E8:B4:4A:ED inet addr:14.x.x.x Bcast:14.67.164.3 Mask:255.255.255.252 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:7148 errors:0 dropped:0 overruns:0 frame:0 TX packets:7659 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2609236 (2.4 MiB) TX bytes:908575 (887.2 KiB) # For giggles if we attempt to launch wpa_supplicant anyways we get this: # wpa_supplicant -Dwext -ieth0 -c/data/misc/wifi/wpa_supplicant.conf wpa_supplicant -Dwext -ieth0 -c/data/misc/wifi/wpa_supplicant.conf ioctl[SIOCSIWPMKSA]: No such device ioctl[SIOCSIWMODE]: No such device Could not configure driver to use managed mode ioctl[SIOCGIFFLAGS]: No such device Could not set interface 'eth0' UP ioctl[SIOCGIWRANGE]: No such device ioctl[SIOCGIFINDEX]: No such device CTRL-EVENT-STATE-CHANGE id=-1 state=0 ioctl[SIOCSIWENCODEEXT]: No such device ioctl[SIOCSIWENCODE]: No such device ioctl[SIOCSIWENCODEEXT]: No such device ioctl[SIOCSIWENCODE]: No such device ioctl[SIOCSIWENCODEEXT]: No such device ioctl[SIOCSIWENCODE]: No such device ioctl[SIOCSIWENCODEEXT]: No such device ioctl[SIOCSIWENCODE]: No such device ioctl[SIOCSIWAUTH]: No such device WEXT auth param 7 value 0x0 - Failed to disable WPA in the driver. ioctl[SIOCSIWAUTH]: No such device WEXT auth param 5 value 0x0 - ioctl[SIOCSIWAUTH]: No such device WEXT auth param 4 value 0x0 - ioctl[SIOCSIWAP]: No such device ioctl[SIOCGIFFLAGS]: No such device # In dmesg we get: <4>[18300.494065] dhd_oob_enable_intr : enable <4>[18305.019976] dhd_net_start failed bus is not ready <4>[18305.020278] dhdsdio_probe: dhd_net_start failed! Do I need to specify the firmware with insmod? Why are we trying to control the interface manually instead of through the Android API? The Android API doesn't support ad-hoc connections as far as I can tell. The card, I am sure, most certainly can.

  Read the article

• /proc/net/dev and /sys/class/net/ bogus network interface names

  - by sfink

  I am constructing a list of network interfaces to monitor based on the contents of /proc/net/dev. But I am getting some bogus interfaces in the list: __tmp1104705027 __tmp974528607 Where do those come from? They also show up in /sys/class/net/: # ls -1 /sys/class/net/ eth0 eth1 eth2 eth3 lo sit0 __tmp1104705027 __tmp974528607 For now, I think I'll just ignore anything starting with __tmp, but I'd like to know what they are and where they come from. This is on a recompiled CentOS 5.3 kernel: 2.6.18-128.7.1.el5.tvh.7PAE #1 SMP PREEMPT

  Read the article

• Virtual Machine with Bridged Adapter to Centos not accepting ssh from host machine [migrated]

  - by javadba

  I have a bridged connection on VirtualBox from os/x 10.8.5 host to Centos 5.8 client. But I suspect this is more of a general issue than specific to the host and precise version of linux. Shown below are the networking info from the VirtualBox and from within the guest sshd is running on port 22: [root@oracle-linux ~]# ps -ef | grep sshd | grep -v grep root 3103 1 0 20:22 ? 00:00:00 /usr/sbin/sshd root 14994 3103 0 21:23 ? 00:00:00 sshd: root@pts/1 Port 22 listening: [root@oracle-linux ~]# netstat -an | grep 22 | grep tcp | grep LIST tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:2207 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:2208 0.0.0.0:* LISTEN tcp 0 0 :::22 :::* LISTEN Here are ip addresses, still on the guest os: [root@oracle-linux ~]# ip addr 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast qlen 1000 link/ether 08:00:27:b9:e5:79 brd ff:ff:ff:ff:ff:ff inet 10.0.15.100/24 brd 10.0.15.255 scope global eth0 inet6 fe80::a00:27ff:feb9:e579/64 scope link valid_lft forever preferred_lft forever 3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast qlen 1000 link/ether 08:00:27:b4:86:8a brd ff:ff:ff:ff:ff:ff inet 10.0.3.15/24 brd 10.0.3.255 scope global eth1 inet6 fe80::a00:27ff:feb4:868a/64 scope link valid_lft forever preferred_lft forever [root@oracle-linux ~]# I can ssh to the guest from the guest: root@oracle-linux ~]# ssh 10.0.3.15 The authenticity of host '10.0.3.15 (10.0.3.15)' can't be established. RSA key fingerprint is ef:08:19:72:95:4d:e5:28:af:f3:6f:54:07:84:ba:04. Are you sure you want to continue connecting (yes/no)? yes Warning: Permanently added '10.0.3.15' (RSA) to the list of known hosts. [email protected]'s password: Last login: Mon Oct 21 21:24:12 2013 from 10.0.15.100 But can NOT ssh from the host to the guest: 18:27:04/shared:11 $ssh [email protected] ssh: connect to host 10.0.15.100 port 22: Operation timed out lost connection Here is bridged connection infO; BTW I looked into other answers, and one of them mentioned doing service iptables stop That did not help. Adapter 2 is a NAT, shown below In case NAT is causing any issues, i shut it down and restarted networking. [root@oracle-linux ~]# /etc/init.d/network restart Shutting down interface eth0: [ OK ] Shutting down interface eth1: Still No joy.. 18:27:04/shared:11 $ssh [email protected] ssh: connect to host 10.0.15.100 port 22: Operation timed out lost connection

  Read the article

• Virtual Machine with Bridged Adapter to Centos not accepting ssh from host machine

  - by javadba

  I have a bridged connection on VirtualBox from os/x 10.8.5 host to Centos 5.8 client. But I suspect this is more of a general issue than specific to the host and precise version of linux. Shown below are the networking info from the VirtualBox and from within the guest sshd is running on port 22: [root@oracle-linux ~]# ps -ef | grep sshd | grep -v grep root 3103 1 0 20:22 ? 00:00:00 /usr/sbin/sshd root 14994 3103 0 21:23 ? 00:00:00 sshd: root@pts/1 Port 22 listening: [root@oracle-linux ~]# netstat -an | grep 22 | grep tcp | grep LIST tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:2207 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:2208 0.0.0.0:* LISTEN tcp 0 0 :::22 :::* LISTEN Here are ip addresses, still on the guest os: [root@oracle-linux ~]# ip addr 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast qlen 1000 link/ether 08:00:27:b9:e5:79 brd ff:ff:ff:ff:ff:ff inet 10.0.15.100/24 brd 10.0.15.255 scope global eth0 inet6 fe80::a00:27ff:feb9:e579/64 scope link valid_lft forever preferred_lft forever 3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast qlen 1000 link/ether 08:00:27:b4:86:8a brd ff:ff:ff:ff:ff:ff inet 10.0.3.15/24 brd 10.0.3.255 scope global eth1 inet6 fe80::a00:27ff:feb4:868a/64 scope link valid_lft forever preferred_lft forever [root@oracle-linux ~]# I can ssh to the guest from the guest: root@oracle-linux ~]# ssh 10.0.3.15 The authenticity of host '10.0.3.15 (10.0.3.15)' can't be established. RSA key fingerprint is ef:08:19:72:95:4d:e5:28:af:f3:6f:54:07:84:ba:04. Are you sure you want to continue connecting (yes/no)? yes Warning: Permanently added '10.0.3.15' (RSA) to the list of known hosts. [email protected]'s password: Last login: Mon Oct 21 21:24:12 2013 from 10.0.15.100 But can NOT ssh from the host to the guest: 18:27:04/shared:11 $ssh [email protected] ssh: connect to host 10.0.15.100 port 22: Operation timed out lost connection Here is bridged connection infO; BTW I looked into other answers, and one of them mentioned doing service iptables stop That did not help. Adapter 2 is a NAT, shown below In case NAT is causing any issues, i shut it down and restarted networking. [root@oracle-linux ~]# /etc/init.d/network restart Shutting down interface eth0: [ OK ] Shutting down interface eth1: Still No joy.. 18:27:04/shared:11 $ssh [email protected] ssh: connect to host 10.0.15.100 port 22: Operation timed out lost connection

  Read the article

• NTPD issue - syncs then slowly loses ground

  - by ethrbunny

  RHEL 5 workstation. Has been running smoothly for years. I did a 'pup' recently and followed with a nice, cleansing reboot. Afterwards the system had some startup issues: namely MySQL refused to start. It just went "...." for 5-10 minutes before I did another boot and skipped that step (using 'interactive'). This was the only service that didn't wan't to start normally. So now that the system is booted I've found that it doesn't want to stay in sync with the NTP master and after 48 hours is refusing any SSH other than root. NTPD: this service starts normally and gets a lock on 4 servers. Almost immediately it starts to lose ground and now (after 3 days) is almost 40 hours behind. If I stop/start the service it gets the lock, resets the system clock and starts losing ground again. The 'hwclock' is set properly and maintains its time. Login: when I (re)start the ntp server I am able to login normally. I assume this problem is due to losing sync with LDAP. This appears to be verified by LDAP errors in /var/log/messages. Suggestions on where to look? ADDENDA: Tried deleting the 'drift' file. After a bit it gets recreated with 0.000. from /var/log/messages: Jan 17 06:54:01 aeolus ntpdate[5084]: step time server 129.95.96.10 offset 30.139216 sec Jan 17 06:54:01 aeolus ntpd[5086]: ntpd [email protected] Tue Oct 25 12:54:17 UTC 2011 (1) Jan 17 06:54:01 aeolus ntpd[5087]: precision = 1.000 usec Jan 17 06:54:01 aeolus ntpd[5087]: Listening on interface wildcard, 0.0.0.0#123 Disabled Jan 17 06:54:01 aeolus ntpd[5087]: Listening on interface wildcard, ::#123 Disabled Jan 17 06:54:01 aeolus ntpd[5087]: Listening on interface lo, ::1#123 Enabled Jan 17 06:54:01 aeolus ntpd[5087]: Listening on interface eth0, fe80::213:72ff:fe20:4080#123 Enabled Jan 17 06:54:01 aeolus ntpd[5087]: Listening on interface lo, 127.0.0.1#123 Enabled Jan 17 06:54:01 aeolus ntpd[5087]: Listening on interface eth0, 10.127.24.81#123 Enabled Jan 17 06:54:01 aeolus ntpd[5087]: kernel time sync status 0040 Jan 17 06:54:02 aeolus ntpd[5087]: frequency initialized 0.000 PPM from /var/lib/ntp/drift Jan 17 06:54:02 aeolus ntpd[5087]: system event 'event_restart' (0x01) status 'sync_alarm, sync_unspec, 1 event, event_unspec' (0xc010) You can see the 30 second offset. This was after about one minute of operation.

  Read the article

• DHCP server with multiple interfaces on ubuntu, destroys default gateway

  - by Henrik Kjus Alstad

  I use Ubuntu, and I have many interfaces. eth0, which is my internet connection, and it gets its info from a DHCP-server totally outisde of my control. I then have eth1,eth2,eth3 and eth4 which I have created a DHCP-server for.(ISC DHCP-Server) It seems to work, and I even get an IP-address from the foreign DHCP-server on the internet facing interface. However, for some reason it seems my gateway for eth0 became screwed after I installed my local DHCP-server for eth1-eth4. (I think so because I got an IP for eth0, and I can ping other stuff on the local network, but I cannot get access to the internet). My eth0-specific info in /etc/network/interfaces: auto lo iface lo inet loopback auto eth0 iface eth0 inet dhcp auto eth1 iface eth1 inet static address 10.0.1.1 netmask 255.255.255.0 network 10.0.1.0 broadcast 10.0.1.255 gateway 10.0.1.1 mtu 8192 auto eth2 iface eth2 inet static address 10.0.2.1 netmask 255.255.255.0 network 10.0.2.0 broadcast 10.0.2.255 gateway 10.0.2.1 mtu 8192 My /etc/default/isc-dhcp-server: INTERFACES="eth1 eth2 eth3 eth4" So why does my local DHCP-server fuck up the gateway for eth0, when I tell it not to listen to eth0? Anyone see the problem or what I can do to fix it? The problem seems indeed to be the gateways. "netstat -nr" gives: 0.0.0.0 --- 10.X.X.X ---- 0.0.0.0 --- UG 0 0 0 eth3 It should have been 0.0.0.0 129.2XX.X.X 0.0.0.0 UG 0 0 0 eth0 So for some reason, my local DHCP-server overrides the gateway I get from the network DHCP. Edit: dhcp.conf looks like this(I included info only for eth1 subnet): ddns-update-style none; not authoritative; subnet 10.0.1.0 netmask 255.255.255.0 { interface eth1; option domain-name "example.org"; option domain-name-servers ns1.example.org, ns2.example.org; default-lease-time 600; max-lease-time 7200; range 10.0.1.10 10.0.1.100; host camera1_1 { hardware ethernet 00:30:53:11:24:6E; fixed-address 10.0.1.10; } host camera2_1 { hardware ethernet 00:30:53:10:16:70; fixed-address 10.0.1.11; } } Also, it seems that the gateway is correctly set if I run "/etc/init.d/networking restart" in a terminal, but that's not helpful for me, I need the correct gateway to be set during startup, and i'd rather find the source of the problem

  Read the article

• Accessing guests on virtual network when connected to host via PPTP

  - by Viktor Elofsson

  I'm setting up a development machine which runs Ubuntu 12.04 and KVM for virtualization. I have a guest running Ubuntu 12.04 which can be accessed from the host via its IP address which is assigned by libvirt. The guest can also access the internet, no problem there. However, now I want to setup PPTP so I can connect to the host (from my workstation running Windows 7) and directly access guests without relying on SSH port forwarding. I can connect from my W7-machine to the host (PPTP), but I cannot access any virtual machines (which are accessable from the host directly). Relevant configuration files cat /etc/network/interfaces auto lo iface lo inet loopback # device: eth0 auto eth0 iface eth0 inet static address x.x.x.x broadcast x.x.x.x netmask x.x.x.x gateway x.x.x.x # default route to access subnet up route add -net x.x.x.x netmask x.x.x.x gw x.x.x.x eth0 virsh net-edit default <network> <name>default</name> <uuid>xxxxxxxx-72ce-3c20-af0f-d3a010f1bef0</uuid> <forward mode='nat'/> <bridge name='virbr0' stp='on' delay='0' /> <mac address='52:54:00:xx:xx:xx'/> <ip address='192.168.122.1' netmask='255.255.255.0'> <dhcp> <range start='192.168.122.2' end='192.168.122.254' /> <host mac='52:54:00:yy:yy:yy' name='web1' ip='192.168.122.11' /> </dhcp> </ip> </network> cat /etc/pptpd.conf (commented lines removed) # TAG: option # Specifies the location of the PPP options file. # By default PPP looks in '/etc/ppp/options' # option /etc/ppp/pptpd-options # TAG: logwtmp # Use wtmp(5) to record client connections and disconnections. # logwtmp #(Recommended) localip 192.168.122.1 remoteip 192.168.122.234-238,192.168.122.245 cat /etc/ppp/chap-secrets* # Secrets for authentication using CHAP # client server secret IP addresses xxxxx * yyyyyyyyyy 192.168.122.100 I get the correct IP address when connecting my W7-machine, but when I try to ping the virtual machine at 192.168.122.11 I get Reply from 192.168.122.1: Destination port unreachable. It's probably something trivial I'm missing but I can't for the life of me figure out what it is. So I'm turning to you, serverfault.

  Read the article

• Links won't open in Outlook

  - by Scott Mitchell

  About a week ago Chrome (my default browser) stopped working and I ended up reinstalling. After that, however, links in Outlook 2007, when clicked, no longer open. Instead, I get a warning that reads: General failure. The URL was: URL. Application not found. I presume that there is some MIME or file type association that needs to be configured at the OS level, but I've not had any luck so far. My operating system is Windows 7. Any ideas? EDIT #1 Wayne Johnston suggested I set Chrome as my default browser, but when I go to the Set Default Programs screen in Windows 7 (via Control Panel) I do not see Chrome in the list of programs. How do I get it to show up there?

  Read the article

• Ubuntu: Multiple NICs, one used only for Wake-On-LAN

  - by jcwx86

  This is similar to some other questions, but I have a specific need which is not covered in the other questions. I have an Ubuntu server (11.10) with two NICs. One is built into the motherboard and the other is a PCI express card. I want to have my server connected to the internet via my NAT router and also have it able to wake from suspend using a Magic Packet (henceforth referred to as Wake-On-LAN, WOL). I can't do this with just one of the NICs because each has an issue - the built-in NIC will crash the system if it is placed under heavy load (typically downloading data), whilst the PCI express NIC will crash the system if it is used for WOL. I have spent some time investigating these individual problems, to no avail. My plan is thus: use the built-in NIC solely for WOL, and use the PCI express card for all other network communication except WOL. Since I send the WOL Magic Packet to a specific MAC address, there is no danger of hitting the wrong NIC, but there is a danger of using the built-in NIC for general network access, overloading it and crashing the system. Both NICs are wired to the same LAN with address space 192.168.0.0/24. The built-in ethernet card is set to have interface name eth1 and the PCI express card is eth0 in Ubuntu's udev persistent rules (so they stay the same upon reboot). I have been trying to set this up with the /etc/network/interfaces file. Here is where I am currently: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 192.168.0.3 netmask 255.255.255.0 network 192.168.0.0 broadcast 192.168.0.255 gateway 192.168.0.1 auto eth1 iface eth1 inet static address 192.168.0.254 netmask 255.255.255.0 I think by not specifying a gateway for eth1, I prevent it being used for outgoing requests. I don't mind if it can be reached on 192.168.0.254 on the LAN, i.e. via SSH -- it's IP is irrelevant to WOL, which is based on MAC addresses -- I just don't want it to be used to access internet resources. My kernel routing table (from route -n) is Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.0.1 0.0.0.0 UG 100 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 eth0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 My question is this: Is this sufficient for what I want to achieve? My research has thrown up the idea of using static routing to specify that eth1 should only be used for WOL on the local network, but I'm not sure this is necessary. I have been monitoring the activity of the interfaces using iptraf and it seems like eth0 takes the vast majority of the packets, though I am not sure that this will be consistent based on my configuration. Given that if I mess up the configuration, my system will likely crash, it is important to me to have this set up correctly!

  Read the article

• iptables & allowed port refusing connection

  - by marfarma

  Can you see what I'm doing wrong? On Ubuntu Server 9.1, I'm attempting to allow traffic on port 1143 for a non-privileged IMAP host. Connection is refused when testing with telnet example.com 1143 but connection is allowed testing with telnet example.com 80 from my pc to remote internet hosted server. Both rules appear identical and are located near each other with no rules rejecting connections intervening in the rules file. I can't figure it out. iptables -L returns this: Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere REJECT all -- anywhere 127.0.0.0/8 reject-with icmp-port-unreachable ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED ACCEPT tcp -- anywhere anywhere tcp dpt:www ACCEPT tcp -- anywhere anywhere tcp dpt:https ACCEPT tcp -- anywhere anywhere tcp dpt:http-alt ACCEPT tcp -- anywhere anywhere tcp dpt:7070 ACCEPT tcp -- anywhere anywhere tcp dpt:1143 ACCEPT tcp -- anywhere anywhere state NEW tcp dpt:ssh ACCEPT icmp -- anywhere anywhere icmp echo-request LOG all -- anywhere anywhere limit: avg 5/min burst 5 LOG level debug prefix `iptables denied: ' REJECT all -- anywhere anywhere reject-with icmp-port-unreachable Chain FORWARD (policy ACCEPT) target prot opt source destination REJECT all -- anywhere anywhere reject-with icmp-port-unreachable Chain OUTPUT (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere and my rules file contains this: # Generated by iptables-save v1.4.4 on Wed May 26 19:08:34 2010 *nat :PREROUTING ACCEPT [3556:217296] :POSTROUTING ACCEPT [6909:414847] :OUTPUT ACCEPT [6909:414847] -A PREROUTING -p tcp -m tcp --dport 80 -j REDIRECT --to-ports 8080 -A PREROUTING -p tcp -m tcp --dport 80 -j REDIRECT --to-ports 8080 COMMIT # Completed on Wed May 26 19:08:34 2010 # Generated by iptables-save v1.4.4 on Wed May 26 19:08:34 2010 *filter :INPUT ACCEPT [1:52] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [1:212] -A INPUT -i lo -j ACCEPT -A INPUT -d 127.0.0.0/8 ! -i lo -j REJECT --reject-with icmp-port-unreachable -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT -A INPUT -p tcp -m tcp --dport 80 -j ACCEPT -A INPUT -p tcp -m tcp --dport 443 -j ACCEPT -A INPUT -p tcp -m tcp --dport 8080 -j ACCEPT -A INPUT -p tcp -m tcp --dport 7070 -j ACCEPT -A INPUT -p tcp -m tcp --dport 1143 -j ACCEPT -A INPUT -p tcp -m state --state NEW -m tcp --dport 22 -j ACCEPT -A INPUT -p icmp -m icmp --icmp-type 8 -j ACCEPT -A INPUT -m limit --limit 5/min -j LOG --log-prefix "iptables denied: " --log-level 7 -A INPUT -j REJECT --reject-with icmp-port-unreachable -A FORWARD -j REJECT --reject-with icmp-port-unreachable -A OUTPUT -j ACCEPT COMMIT # Completed on Wed May 26 19:08:34 2010

  Read the article

• FTP not listing files behind firewall (setsockopt (ignored): Permission denied)

  - by KennyDs

  We are developing a Magento application that has a module that works with FTP. Today we deployed this on the testing environment which is setup in the following way: Gateway server which has the following iptables rules: # iptables -L -n -v Chain INPUT (policy ACCEPT 2 packets, 130 bytes) pkts bytes target prot opt in out source destination 0 0 ACCEPT all -- lo * 0.0.0.0/0 0.0.0.0/0 165 13720 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED Chain FORWARD (policy ACCEPT 7 packets, 606 bytes) pkts bytes target prot opt in out source destination 0 0 ACCEPT all -- eth1 eth0 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 15 965 ACCEPT all -- eth0 eth1 0.0.0.0/0 0.0.0.0/0 0 0 REJECT all -- eth1 eth1 0.0.0.0/0 0.0.0.0/0 reject-with icmp-port-unreachable Chain OUTPUT (policy ACCEPT 126 packets, 31690 bytes) pkts bytes target prot opt in out source destination These are set at runtime via the following bash script: #!/bin/sh PATH=/usr/sbin:/sbin:/bin:/usr/bin # # delete all existing rules. # iptables -F iptables -t nat -F iptables -t mangle -F iptables -X # Always accept loopback traffic iptables -A INPUT -i lo -j ACCEPT # Allow established connections, and those not coming from the outside iptables -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A FORWARD -i eth1 -o eth0 -m state --state ESTABLISHED,RELATED -j ACCEPT # Allow outgoing connections from the LAN side. iptables -A FORWARD -i eth0 -o eth1 -j ACCEPT # Masquerade. iptables -t nat -A POSTROUTING -o eth1 -j MASQUERADE # Don't forward from the outside to the inside. iptables -A FORWARD -i eth1 -o eth1 -j REJECT # Enable routing. echo 1 > /proc/sys/net/ipv4/ip_forward The gateway server is connected to the WAN via eth1 and is connected to the internal network via eth0. One of the servers from eth1 has the following problem when trying to list files over ftp: $ ftp -vd myftpserver.com Connected to myftpserver.com 220 Welcome to MY FTP Server ftp: setsockopt: Bad file descriptor Name (myftpserver.com:magento): XXXXXXXX ---> USER XXXXXXXX 331 User XXXXXXXX, password please Password: ---> PASS XXXX 230 Password Ok, User logged in ---> SYST 215 UNIX Type: L8 Remote system type is UNIX. Using binary mode to transfer files. ftp> ls ftp: setsockopt (ignored): Permission denied ---> PORT 192,168,19,15,135,75 421 Service not available, remote server has closed connection When I try listing the files in passive mode, same result. When I run the same command on the gateway server, everything works fine so I believe that the issue is happening because of the iptables rules not forwarding properly. Does anyone have an idea which rule I need to add to make this work?

  Read the article

• Keep source IP after NAT

  - by John Miller

  Until today I used a cheapy router so I can share my internet connection and keep a webserver online too, while using NAT. Users IP ($_SERVER['REMOTE_ADDR']) was fine, I was seeing class A IPs of users. But as traffic grown up everyday, I had to install a Linux Server (Debian) to share my Internet Connection, because my old router couldn't keep the traffic anymore. I shared the internet via IPTABLES using NAT, but now, after forwarding port 80 to my webserver, now instead of seeing real users IP, I see my Gateway IP (Linux Internal IP) as any user IP Address. How to solve this issue? I edited my post, so I can paste the rules I'm currently using. #!/bin/sh #I made a script to set the rules #I flush everything here. iptables --flush iptables --table nat --flush iptables --delete-chain iptables --table nat --delete-chain iptables -F iptables -X # I drop everything as a general rule, but this is disabled under testing # iptables -P INPUT DROP # iptables -P OUTPUT DROP # these are the loopback rules iptables -A INPUT -i lo -j ACCEPT iptables -A OUTPUT -o lo -j ACCEPT # here I set the SSH port rules, so I can connect to my server iptables -A INPUT -p tcp --sport 513:65535 --dport 22 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -p tcp --sport 22 --dport 513:65535 -m state --state ESTABLISHED -j ACCEPT # These are the forwards for 80 port iptables -t nat -A PREROUTING -p tcp -s 0/0 -d xx.xx.xx.xx --dport 80 -j DNAT --to 192.168.42.3:80 iptables -t nat -A POSTROUTING -o eth0 -d xx.xx.xx.xx -j SNAT --to-source 192.168.42.3 iptables -A FORWARD -p tcp -s 192.168.42.3 --sport 80 -j ACCEPT # These are the forwards for bind/dns iptables -t nat -A PREROUTING -p udp -s 0/0 -d xx.xx.xx.xx --dport 53 -j DNAT --to 192.168.42.3:53 iptables -t nat -A POSTROUTING -o eth0 -d xx.xx.xx.xx -j SNAT --to-source 192.168.42.3 iptables -A FORWARD -p udp -s 192.168.42.3 --sport 53 -j ACCEPT # And these are the rules so I can share my internet connection iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE iptables -A FORWARD -i eth0:1 -j ACCEPT If I delete the MASQUERADE part, I see my real IP while echoing it with PHP, but I don't have internet. How to do, to have internet and see my real IP while ports are forwarded too? ** xx.xx.xx.xx - is my public IP. I hid it for security reasons.

  Read the article

• Routing all data through an VPN tunnel with ppp

  - by Oliver

  I'm trying to create a VPN tunnel that forwards all data from the local machine to the VPN server. I'm using ppp-2.4.5 for this with the following configuration: pty "pptp <VPNServer> --nolaunchpppd" name <my login name> remotename PPTP usepeerdns require-mppe-128 file /etc/ppp/options.pptp persist maxfail 0 holdoff 5 I have a script in if-up.d with the following content: route del default eth0 route add default dev ppp0 Before starting the VPN tunnel my routing looks like: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.0.1 0.0.0.0 UG 2 0 0 eth0 127.0.0.0 127.0.0.1 255.0.0.0 UG 0 0 0 lo 192.168.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 After starting the tunnel (via pon) it looks like: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 0.0.0.0 0.0.0.0 U 0 0 0 ppp0 12.34.56.1 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 127.0.0.0 127.0.0.1 255.0.0.0 UG 0 0 0 lo 192.168.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 Now the problem is, that the VPN tunnel seems to be looped into itself. If I run ifconfig after a few seconds without any traffic: eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet 192.168.0.10 netmask 255.255.0.0 broadcast 192.168.255.255 ether 00:01:2e:2f:ff:35 txqueuelen 1000 (Ethernet) RX packets 39931 bytes 6784614 (6.4 MiB) RX errors 0 dropped 90 overruns 0 frame 0 TX packets 34980 bytes 7633181 (7.2 MiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 device interrupt 20 memory 0xfbdc0000-fbde0000 ppp0: flags=4305<UP,POINTOPOINT,RUNNING,NOARP,MULTICAST> mtu 1496 inet 12.34.56.78 netmask 255.255.255.255 destination 12.34.56.1 ppp txqueuelen 3 (Point-to-Point Protocol) RX packets 7 bytes 94 (94.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 782863 bytes 349257986 (333.0 MiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 It states that already over 300 MiB have been send, ppp0 is only online since a few seconds and the connection isn't working anyway. Can someone please help me to fix the routing table, so that the traffic from ppp0 is not send again through ppp0 but instead goes to the remote server?

  Read the article

• SSH stops at "using username" with IPTables in effect

  - by Rautamiekka

  We used UFW but couldn't make the Source Dedicated ports open, which was weird, so we purged UFW and switched to IPTables, using Webmin to configure. If the inbound chain is on DENY and SSH port open [judged from Webmin], PuTTY will say using username "root" and stops at that instead of asking for public key pw. Inbound chain on ACCEPT the pw is asked. This problem didn't happen with UFW. Picture of IPTables configuration in Webmin: http://s284544448.onlinehome.us/public/PlusLINE%20Dedicated%20Server,%20Webmin,%20IPTables,%200.jpgThe address is to the previous rautamiekka.org. iptables-save when on INPUT DENY: # Generated by iptables-save v1.4.8 on Wed Apr 11 16:09:20 2012 *mangle :PREROUTING ACCEPT [1430:156843] :INPUT ACCEPT [1430:156843] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [1415:781598] :POSTROUTING ACCEPT [1415:781598] COMMIT # Completed on Wed Apr 11 16:09:20 2012 # Generated by iptables-save v1.4.8 on Wed Apr 11 16:09:20 2012 *nat :PREROUTING ACCEPT [2:104] :POSTROUTING ACCEPT [0:0] :OUTPUT ACCEPT [0:0] COMMIT # Completed on Wed Apr 11 16:09:20 2012 # Generated by iptables-save v1.4.8 on Wed Apr 11 16:09:20 2012 *filter :INPUT DROP [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [1247:708906] -A INPUT -i lo -m comment --comment "Machine-within traffic - always allowed" -j ACCEPT -A INPUT -p tcp -m comment --comment "Services - TCP" -m tcp -m multiport --dports 22,80,443,10000,20,21 -m state --state NEW,ESTABLISHED -j ACCEPT -A INPUT -p tcp -m comment --comment "Minecraft - TCP" -m tcp --dport 25565 -j ACCEPT -A INPUT -p udp -m comment --comment "Minecraft - UDP" -m udp --dport 25565 -j ACCEPT -A INPUT -p tcp -m comment --comment "Source Dedicated - TCP" -m tcp --dport 27015 -j ACCEPT -A INPUT -p udp -m comment --comment "Source Dedicated - UDP" -m udp -m multiport --dports 4380,27000:27030 -j ACCEPT -A INPUT -p udp -m comment --comment "TS3 - UDP - main port" -m udp --dport 9987 -j ACCEPT -A INPUT -p tcp -m comment --comment "TS3 - TCP - ServerQuery" -m tcp --dport 10011 -j ACCEPT -A OUTPUT -o lo -m comment --comment "Machine-within traffic - always allowed" -j ACCEPT COMMIT # Completed on Wed Apr 11 16:09:20 2012 iptables --list when on INPUT DENY: Chain INPUT (policy DROP) target prot opt source destination ACCEPT all -- anywhere anywhere /* Machine-within traffic - always allowed */ ACCEPT tcp -- anywhere anywhere /* Services - TCP */ tcp multiport dports ssh,www,https,webmin,ftp-data,ftp state NEW,ESTABLISHED ACCEPT tcp -- anywhere anywhere /* Minecraft - TCP */ tcp dpt:25565 ACCEPT udp -- anywhere anywhere /* Minecraft - UDP */ udp dpt:25565 ACCEPT tcp -- anywhere anywhere /* Source Dedicated - TCP */ tcp dpt:27015 ACCEPT udp -- anywhere anywhere /* Source Dedicated - UDP */ udp multiport dports 4380,27000:27030 ACCEPT udp -- anywhere anywhere /* TS3 - UDP - main port */ udp dpt:9987 ACCEPT tcp -- anywhere anywhere /* TS3 - TCP - ServerQuery */ tcp dpt:10011 Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere /* Machine-within traffic - always allowed */ The UFW rules prior to purging on INPUT DENY: 127.0.0.1 ALLOW IN 127.0.0.1 3306 DENY IN Anywhere 20,21/tcp ALLOW IN Anywhere 22/tcp (OpenSSH) ALLOW IN Anywhere 80/tcp ALLOW IN Anywhere 443/tcp ALLOW IN Anywhere 989 ALLOW IN Anywhere 990 ALLOW IN Anywhere 8075/tcp ALLOW IN Anywhere 9987/udp ALLOW IN Anywhere 10000/tcp ALLOW IN Anywhere 10011/tcp ALLOW IN Anywhere 25565/tcp ALLOW IN Anywhere 27000:27030/tcp ALLOW IN Anywhere 4380/udp ALLOW IN Anywhere 27014:27050/tcp ALLOW IN Anywhere 30033/tcp ALLOW IN Anywhere

  Read the article

• how to use iptables to block the IP of device connected to openwrt router

  - by scola

  I have two routers(A,B).the A connect to internet with IP:192.168.1.1 The openwrt router B connect the lan of A by bridge with static IP:192.168.1.111. I am learning to use iptables to control the devices connected to B(wlan) . I use my phone to connect wifi of B,the phone's IP is IP:192.168.1.100.it can surf the internet normally. I want to block the phone's IP to make the phone can not connect to internet. refer to http://bredsaal.dk/some-small-iptables-on-openwrt-tips iptables -A input_wan -s 192.168.1.100 --jump REJECT iptables -A forwarding_rule -d 192.168.1.100 --jump REJECT but it do not work.the phone still connect to internet normally. and I tried other chain(INPUT,OUTPUT,FORWARD).so many chains confused me. iptables -I OUTPUT -o br-lan -s 192.168.1.100 -j DROP and it do not work again. I'm sure that the iptables have no problem. root@OpenWrt:/etc# iptables -L|grep Chain Chain INPUT (policy ACCEPT) Chain FORWARD (policy DROP) Chain OUTPUT (policy ACCEPT) Chain forward (1 references) Chain forwarding_lan (1 references) Chain forwarding_rule (1 references) Chain forwarding_wan (1 references) Chain input (1 references) Chain input_lan (1 references) Chain input_rule (1 references) Chain input_wan (1 references) Chain output (1 references) root@OpenWrt:/etc# ifconfig br-lan Link encap:Ethernet HWaddr 0C:82:68:97:57:BA inet addr:192.168.1.111 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::e82:68ff:fe97:57ba/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:14976 errors:0 dropped:0 overruns:0 frame:0 TX packets:7656 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2851980 (2.7 MiB) TX bytes:1902785 (1.8 MiB) eth0 Link encap:Ethernet HWaddr 0C:82:68:97:57:BA UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:58201 errors:0 dropped:11 overruns:0 frame:0 TX packets:45012 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:54591348 (52.0 MiB) TX bytes:5711142 (5.4 MiB) Interrupt:4 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:312 errors:0 dropped:0 overruns:0 frame:0 TX packets:312 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:39961 (39.0 KiB) TX bytes:39961 (39.0 KiB) mon.wlan0 Link encap:UNSPEC HWaddr 0C-82-68-97-57-BA-00-48-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4900 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:1223807 (1.1 MiB) TX bytes:0 (0.0 B) wlan0 Link encap:Ethernet HWaddr 0C:82:68:97:57:BA UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:37346 errors:0 dropped:0 overruns:0 frame:0 TX packets:49662 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:3808021 (3.6 MiB) TX bytes:54486310 (51.9 MiB) root@OpenWrt:/etc/config# cat network config 'interface' 'loopback' option 'ifname' 'lo' option 'proto' 'static' option 'ipaddr' '127.0.0.1' option 'netmask' '255.0.0.0' config 'interface' 'lan' option 'ifname' 'eth0' option 'type' 'bridge' option 'proto' 'static' option 'ipaddr' '192.168.1.111' option 'netmask' '255.255.255.0' option 'gateway' '192.168.1.1' option dns 192.168.1.1 and how to use iptables to control the network of wlan? Thanks in advance and sorry for poor English.

  Read the article

• Delete files from directory: memory exhausted

  - by codeholic

  This question is a logical continuation of http://serverfault.com/questions/45245/how-can-i-delete-all-files-from-a-directory-when-it-reports-argument-list-too-lo I have drwxr-xr-x 2 doreshkin doreshkin 198291456 Apr 6 21:35 session_data I tried find session_data -type f -delete find session_data -type f | xargs rm -f find session_data -maxdepth 1 -type f -print0 | xargs -r0 rm -f The result is the same: find: memory exhausted What can I do to remove this directory?

  Read the article

• Do I need a hardware firewall for Win 2003?

  - by user531723

  We have had a Win 2003 server at a co-lo for a while. It is used as a web server and has a very cheap hardware firewall between it and the internet. Ports 3389 and 80 are the only ones forwarded to the server. I am doing some upgrading and wondering if I really need the firewall. Are there any drawbacks to just using the Win 2003 built in firewall to make sure only traffic on 3389 and 80 get through?

  Read the article

• Can only bring up one of two interfaces

  - by mstaessen

  I'm having a bizarre issue with my HP Proliant DL 360 G4p server. It has two gigabit ethernet interfaces but I can bring up only one of them. This is starting to freak me out and that's why I turned here. I'm running the x64 ubuntu 11.10 server edition. lshw -c network shows that the second interface is disabled. I have no idea why ans how to enable it. $ sudo lshw -c network *-network:0 description: Ethernet interface product: NetXtreme BCM5704 Gigabit Ethernet vendor: Broadcom Corporation physical id: 2 bus info: pci@0000:02:02.0 logical name: eth0 version: 10 serial: 00:18:71:e3:6d:26 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 66MHz capabilities: pcix pm vpd msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.119 duplex=full firmware=5704-v3.27b, ASFIPMIc v2.36 ip=10.48.8.x latency=64 link=yes mingnt=64 multicast=yes port=twisted pair speed=100Mbit/s resources: irq:25 memory:fdf70000-fdf7ffff *-network:1 DISABLED description: Ethernet interface product: NetXtreme BCM5704 Gigabit Ethernet vendor: Broadcom Corporation physical id: 2.1 bus info: pci@0000:02:02.1 logical name: eth1 version: 10 serial: 00:18:71:e3:6d:25 capacity: 1Gbit/s width: 64 bits clock: 66MHz capabilities: pcix pm vpd msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.119 firmware=5704-v3.27b latency=64 link=no mingnt=64 multicast=yes port=twisted pair resources: irq:26 memory:fdf60000-fdf6ffff If I try to ifup eth1, then I get $ sudo ifup eth1 Ignoring unknown interface eth1=eth1. I figured that's what happens when there is no eth1 listed in /etc/network/interfaces. But when I add the configuration for eth1, I still can't ifup. $ sudo ifup eth1 RTNETLINK answers: File exists Failed to bring up eth1. I've also tried ifconfig eth1 up but without any result. For clarity, I have added a masked version of /etc/network/interfaces. I don't think it is the cause of the problem though. $ cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address 10.48.8.x netmask 255.255.255.y network 10.48.8.z broadcast 10.48.8.t gateway 10.48.8.u auto eth1 iface eth1 inet static address 193.190.253.x netmask 255.255.255.y network 193.190.253.z broadcast 193.190.253.t gateway 193.190.253.u I really need some help fixing this. It's driving me crazy. Thanks.

  Read the article

• arp "who-has tell" on cloned machine

  - by mcmorry

  I have a urgent problem to solve today, but I'm lost. Please help. I've cloned a Virtual Machine hosted on VM Ware ESXi 4.1 The OS is now Ubuntu Server 12.04 LTS, but at the time of cloning it was 10.04 LTS. I fixed the MAC address manually inside /etc/udev/rules.d/70-persistent-net.rules. It is a known problem on Ubuntu. I had to remove the old MAC address and set the new one as eth0. Everything seems to work fine, except ARP. My provider OVH sent me a warning to resolve it today (this is the second day) or they will block my IP! The log contains many lines like this: Tue Jun 5 01:04:29 2012 : arp who-has 178.32.136.212 tell 178.32.136.224 where .224 is the cloned server that is causing problems, and .212 is the cloned one. arp -na returns: ? (178.33.230.254) at 00:07:b4:00:00:02 [ether] on eth0 ? (178.32.136.212) at 00:50:56:09:8e:f1 [ether] on eth0 The first IP is the ESXi machine. The second one should not be there. I'm not an expert and I don't know what else to do to fix this problem. Any help will be very appreciated. Thanks. EDIT: ifcofig on .224: eth0 Link encap:Ethernet HWaddr 00:50:56:01:32:c6 inet addr:178.32.136.224 Bcast:178.32.136.255 Mask:255.255.255.0 inet6 addr: fe80::250:56ff:fe01:32c6/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:399924 errors:0 dropped:465 overruns:0 frame:0 TX packets:241884 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:58006071 (58.0 MB) TX bytes:663603166 (663.6 MB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:516216 errors:0 dropped:0 overruns:0 frame:0 TX packets:516216 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:236284275 (236.2 MB) TX bytes:236284275 (236.2 MB) ifconfig on .212: eth0 Link encap:Ethernet HWaddr 00:50:56:09:8e:f1 inet addr:178.32.136.212 Bcast:178.32.136.255 Mask:255.255.255.0 inet6 addr: fe80::250:56ff:fe09:8ef1/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:16014 errors:0 dropped:0 overruns:0 frame:0 TX packets:14511 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:15134444 (15.1 MB) TX bytes:2683025 (2.6 MB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:9944 errors:0 dropped:0 overruns:0 frame:0 TX packets:9944 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1139347 (1.1 MB) TX bytes:1139347 (1.1 MB)

  Read the article

• iptables: Allow only HTTP access for web browsing

  - by user1448260

  Have a linux box, want it locked down but just be able to surf internet on it. Why is this script blocking http too? #!/bin/sh # # iptables -F # #Set default policies for INPUT, FORWARD and OUTPUT chains # iptables -P INPUT DROP iptables -P FORWARD DROP iptables -P OUTPUT DROP # # Allow TCP connections on tcp port 80 # iptables -A INPUT -i eth0 -p tcp --dport 80 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -o eth0 -p tcp --sport 80 -m state --state ESTABLISHED -j ACCEPT # # Set access for localhost # iptables -A INPUT -i lo -j ACCEPT # # List rules # iptables -L -v

  Read the article

• Can't ping Ip over bridge

  - by tmn29a

  I'm unable to ping another host over a bridge I created, I can't see the error -.- It's a remote machine running debian stable with some backports for which I want to set up DHCP on the new Subnet 172.30.xxx.xxx to be used for KVM-Guests. ifconfig : bond0 Link encap:Ethernet HWaddr e4:11:5b:d4:94:30 inet addr:10.54.2.84 Bcast:10.54.2.127 Mask:255.255.255.192 inet6 addr: fe80::e611:5bff:fed4:9430/64 Scope:Link UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1 RX packets:34277 errors:0 dropped:0 overruns:0 frame:0 TX packets:18379 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2638709 (2.5 MiB) TX bytes:2887894 (2.7 MiB) br0 Link encap:Ethernet HWaddr f2:fc:4d:7f:15:f0 inet addr:172.30.254.66 Bcast:172.30.254.127 Mask:255.255.255.192 inet6 addr: fe80::f0fc:4dff:fe7f:15f0/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:252 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:10800 (10.5 KiB) Pings : ping -I br0 172.30.xxx.65 PING 172.30.xxx.65 (172.30.xxx.65) from 172.30.xxx.66 br0: 56(84) bytes of data. --- 172.30.xxx.65 ping statistics --- 3 packets transmitted, 0 received, 100% packet loss, time 2017ms ping -I bond0 172.30.254.65 PING 172.30.xxx.65 (172.30.xxx.65) from 10.54.2.84 bond0: 56(84) bytes of data. 64 bytes from 172.30.x.65: icmp_req=1 ttl=64 time=0.599 ms 64 bytes from 172.30.x.65: icmp_req=2 ttl=64 time=0.575 ms 64 bytes from 172.30.x.65: icmp_req=3 ttl=64 time=0.565 ms --- 172.30.x.65 ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 1999ms rtt min/avg/max/mdev = 0.565/0.579/0.599/0.031 ms Route : Destination Gateway Genmask Flags Metric Ref Use Iface 172.30.x.64 * 255.255.255.192 U 0 0 0 br0 10.54.x.64 * 255.255.255.192 U 0 0 0 bond0 default 10.54.x.65 0.0.0.0 UG 0 0 0 bond0 default 172.30.x.65 0.0.0.0 UG 0 0 0 br0 The Interface : cat /etc/network/interfaces auto lo br0 iface lo inet loopback # Bonding Interface auto bond0 iface bond0 inet static address 10.54.x.84 netmask 255.255.255.192 network 10.54.x.64 gateway 10.54.x.65 slaves eth0 eth1 bond_mode active-backup bond_miimon 100 bond_downdelay 200 bond_updelay 200 iface br0 inet static bridge_ports bond0 address 172.30.x.66 broadcast 172.30.x.127 netmask 255.255.x.192 gateway 172.30.x.65 bridge_maxwait 0 If you need more info please ask. Thanks for your help !

  Read the article

< Previous Page | 18 19 20 21 22 23 24 25 26 27 28 29  | Next Page >