Search Results

Search found 5628 results on 226 pages for 'cpu hogging'.

Page 220/226 | < Previous Page | 216 217 218 219 220 221 222 223 224 225 226  | Next Page >

• FreeBSD high load loopback interface

  - by user1740915

  I have a problem with a FreeBSD server. There is a FreeBSD 9.0 amd64, two network cards em1 (internet), em0 (local network) configured firewall ipfw, natd, squid (not transparent), the server acts as a gateway for access to the Internet. Next problem: upload via squid is very low. At this moment I see next: natd, dhcpd load the cpu at that time when uploading through squid and there are a lot of traffic through the loopback interface. ipfw show output 0100 655389684 36707144666 allow ip from any to any via lo0 00200 0 0 deny ip from any to 127.0.0.0/8 00300 0 0 deny ip from 127.0.0.0/8 to any 00400 0 0 deny ip from any to ::1 00500 0 0 deny ip from ::1 to any 00600 4 292 allow ipv6-icmp from :: to ff02::/16 00700 0 0 allow ipv6-icmp from fe80::/10 to fe80::/10 00800 1 76 allow ipv6-icmp from fe80::/10 to ff02::/16 00900 0 0 allow ipv6-icmp from any to any ip6 icmp6types 1 01000 0 0 allow ipv6-icmp from any to any ip6 icmp6types 2,135,136 01100 1615 76160 deny ip from 192.168.1.1 to any in via em1 01200 0 0 deny ip from 199.69.99.11 to any in via em0 01300 46652 3705426 deny ip from any to 172.16.0.0/12 via em1 01400 3936404 345618870 deny ip from any to 192.168.0.0/16 via em1 01500 4 336 deny ip from any to 0.0.0.0/8 via em1 01600 4129 387621 deny ip from any to 169.254.0.0/16 via em1 01700 0 0 deny ip from any to 192.0.2.0/24 via em1 01800 917566 33777571 deny ip from any to 224.0.0.0/4 via em1 01900 147872 22029252 deny ip from any to 240.0.0.0/4 via em1 02000 1132194739 1190981955947 divert 8668 ip4 from any to any via em1 02100 3 248 deny ip from 172.16.0.0/12 to any via em1 02200 35925 2281289 deny ip from 192.168.0.0/16 to any via em1 02300 1808 122494 deny ip from 0.0.0.0/8 to any via em1 02400 3 174 deny ip from 169.254.0.0/16 to any via em1 02500 0 0 deny ip from 192.0.2.0/24 to any via em1 02600 0 0 deny ip from 224.0.0.0/4 to any via em1 02700 0 0 deny ip from 240.0.0.0/4 to any via em1 02800 960156249 1095316736582 allow tcp from any to any established 02900 64236062 8243196577 allow ip from any to any frag 03000 34 1756 allow tcp from any to me dst-port 25 setup 03100 193 11580 allow tcp from any to me dst-port 53 setup 03200 63 4222 allow udp from any to me dst-port 53 03300 64 8350 allow udp from me 53 to any 03400 417 24140 allow tcp from any to me dst-port 80 setup 03500 211 10472 allow ip from any to me dst-port 3389 setup 05300 77 4488 allow ip from any to me dst-port 1723 setup 05400 3 156 allow ip from any to me dst-port 8443 setup 05500 9882 590596 allow tcp from any to me dst-port 22 setup 05600 1 60 allow ip from any to me dst-port 2000 setup 05700 0 0 allow ip from any to me dst-port 2201 setup 07400 4241779 216690096 deny log logamount 1000 ip4 from any to any in via em1 setup proto tcp 07500 21135656 1048824936 allow tcp from any to any setup 07600 474447 35298081 allow udp from me to any dst-port 53 keep-state 07700 532 40612 allow udp from me to any dst-port 123 keep-state 65535 1990638432 1122305322718 allow ip from any to any systat -ifstat when uploading via squid Load Average ||| Interface Traffic Peak Total tun0 in 79.507 KB/s 232.479 KB/s 42.314 GB out 2.022 MB/s 2.424 MB/s 59.662 GB lo0 in 4.450 MB/s 4.450 MB/s 43.723 GB out 4.450 MB/s 4.450 MB/s 43.723 GB em1 in 2.629 MB/s 2.982 MB/s 464.533 GB out 2.493 MB/s 2.875 MB/s 484.673 GB em0 in 240.458 KB/s 296.941 KB/s 442.368 GB out 512.508 KB/s 850.857 KB/s 416.122 GB top output PID USERNAME THR PRI NICE SIZE RES STATE C TIME WCPU COMMAND 66885 root 1 92 0 26672K 2784K CPU3 3 528:43 65.48% natd 9160 dhcpd 1 45 0 31032K 9280K CPU1 1 7:40 32.96% dhcpd 66455 root 1 20 0 18344K 2856K select 1 119:27 1.37% openvpn 16043 squid 1 20 0 44404K 17884K kqread 2 0:22 0.29% squid squid.conf cat /usr/local/etc/squid/squid.conf # # Recommended minimum configuration: # acl manager proto cache_object acl localhost src 127.0.0.1/32 ::1 acl to_localhost dst 127.0.0.0/8 0.0.0.0/32 ::1 # Example rule allowing access from your local networks. # Adapt to list your (internal) IP networks from where browsing # should be allowed acl localnet src 10.0.0.0/8 # RFC1918 possible internal network acl localnet src 172.16.0.0/12 # RFC1918 possible internal network acl localnet src 192.168.0.0/16 # RFC1918 possible internal network acl localnet src fc00::/7 # RFC 4193 local private network range acl localnet src fe80::/10 # RFC 4291 link-local (directly plugged) machines acl SSL_ports port 443 acl Safe_ports port 80 # http acl Safe_ports port 21 # ftp acl Safe_ports port 443 # https acl Safe_ports port 70 # gopher acl Safe_ports port 210 # wais acl Safe_ports port 1025-65535 # unregistered ports acl Safe_ports port 280 # http-mgmt acl Safe_ports port 488 # gss-http acl Safe_ports port 591 # filemaker acl Safe_ports port 777 # multiling http acl CONNECT method CONNECT # # Recommended minimum Access Permission configuration: # # Only allow cachemgr access from localhost http_access allow manager localhost http_access deny manager # Deny requests to certain unsafe ports http_access deny !Safe_ports # Deny CONNECT to other than secure SSL ports http_access deny CONNECT !SSL_ports # We strongly recommend the following be uncommented to protect innocent # web applications running on the proxy server who think the only # one who can access services on "localhost" is a local user http_access deny to_localhost # # INSERT YOUR OWN RULE(S) HERE TO ALLOW ACCESS FROM YOUR CLIENTS # # Example rule allowing access from your local networks. # Adapt localnet in the ACL section to list your (internal) IP networks # from where browsing should be allowed http_access allow localnet http_access allow localhost # And finally deny all other access to this proxy http_access deny all # Squid normally listens to port 3128 http_port 192.168.1.1:3128 # Uncomment and adjust the following to add a disk cache directory. #cache_dir ufs /var/squid/cache 100 16 256 # Leave coredumps in the first cache dir coredump_dir /var/squid/cache I understand that the traffic passes through the SQUID several times. But can not find why.

  Read the article

• Win32 -- Object cleanup and global variables

  - by KaiserJohaan

  Hello, I've got a question about global variables and object cleanup in c++. For example, look at the code here; case WM_PAINT: paintText(&hWnd); break; void paintText(HWND* hWnd) { PAINTSTRUCT ps; HBRUSH hbruzh = CreateSolidBrush(RGB(0,0,0)); HDC hdz = BeginPaint(*hWnd,&ps); char s1[] = "Name"; char s2[] = "IP"; SelectBrush(hdz,hbruzh); SelectFont(hdz,hFont); SetBkMode(hdz,TRANSPARENT); TextOut(hdz,3,23,s1,sizeof(s1)); TextOut(hdz,10,53,s2,sizeof(s2)); EndPaint(*hWnd,&ps); DeleteObject(hdz); DeleteObject(hbruzh); // bad? DeleteObject(ps); // bad? } 1)First of all; which objects are good to delete and which ones are NOT good to delete and why? Not 100% sure of this. 2)Since WM_PAINT is called everytime the window is redrawn, would it be better to simply store ps, hdz and hbruzh as global variables instead of re-initializing them everytime? The downside I guess would be tons of global variables in the end _ but performance-wise would it not be less CPU-consuming? I know it won't matter prolly but I'm just aiming for minimalistic as possible for educational purposes. 3) What about libraries that are loaded in? For example: // // Main // int WINAPI WinMain(HINSTANCE hInstance, HINSTANCE hPrevInstance, LPSTR lpCmdLine, int nCmdShow) { // initialize vars HWND hWnd; WNDCLASSEX wc; HINSTANCE hlib = LoadLibrary("Riched20.dll"); ThishInstance = hInstance; ZeroMemory(&wc,sizeof(wc)); // set WNDCLASSEX props wc.cbSize = sizeof(WNDCLASSEX); wc.lpfnWndProc = WindowProc; wc.hInstance = ThishInstance; wc.hIcon = LoadIcon(hInstance,MAKEINTRESOURCE(IDI_MYICON)); wc.lpszMenuName = MAKEINTRESOURCE(IDR_MENU1); wc.hCursor = LoadCursor(NULL, IDC_ARROW); wc.hbrBackground = (HBRUSH)COLOR_WINDOW; wc.lpszClassName = TEXT("PimpClient"); RegisterClassEx(&wc); // create main window and display it hWnd = CreateWindowEx(NULL, wc.lpszClassName, TEXT("PimpClient"), 0, 300, 200, 450, 395, NULL, NULL, hInstance, NULL); createWindows(&hWnd); ShowWindow(hWnd,nCmdShow); // loop message queue MSG msg; while (GetMessage(&msg, NULL,0,0)) { TranslateMessage(&msg); DispatchMessage(&msg); } // cleanup? FreeLibrary(hlib); return msg.wParam; } 3cont) is there a reason to FreeLibrary at the end? I mean when the process terminates all resources are freed anyway? And since the library is used to paint text throughout the program, why would I want to free before that? Cheers

  Read the article

• My server app works strangely. What could be the reason(s)?

  - by Poni

  Hi! I've written a server app (two parts actually; proxy server and a game server) using C++ (board game). It uses IOCP as the sockets interface. For that app I've also written a "client simulator" (hereafter "client") app that spawns many client connections, where each of them plays, in very high speed, getting the CPU to be 100% utilized. So, that's how it goes in terms of topology: Game server - holds the game state. Real players do not connect it directly but through the proxy server. When a player joins a game, the proxy actually asks for it on behalf of that player, and the game server spawns a "player instance" for that player, and from now on, every notification between the game server and the player is being passed through the proxy. Proxy server - holds TCP connections with the real players. Players communicate with the game server through it only. Client simulator - connects to the proxy only. When running the server (again, it's actually two server apps) & client locally it all works just fine. I'm talking about 40k+ player instances in which all of them are active in a game. On the other hand, when running the server remotely with, say, 1000 clients who play things getting strange. For example, I run it as said above. Then with Task Manager I kill the client simulator app ("End Process Tree"). Then it seems like the buffer of the remote server got modified by another thread, or in other words, a memory corruption has been occurred. The server crashes because it got an unknown message id (it's a custom protocol where each message has it's own unique number). To make things clear, here is how I run the apps: PC1 - game server and clients simulator (because the clients will connect the proxy). PC2 - proxy server. The strangest thing is this: Only the remote side gets "corrupted". Remote in terms that it's not the PC I use to code the app (VC++ 2008). Let's call the PC I use to code the apps "PC1". Now for example, if this time I ran the game server on PC1 (it means that proxy server on PC2 and clients simulator on PC1), then the proxy server crashes with an "unknown message id" error. Another variation is when I run the proxy server on PC1 (again, the dev machine), the game server and the clients simulator on PC2, then the game server on PC2 gets crashed. As for the IOCP config: The servers' internal connections use the default receive/send buffer sizes. Tried even with setting them to 1MB, but no luck. I have three PCs in total; 2 x Vista 64bit <<-- one of those is the dev machine. The other is connected through WiFi. 1 x WinXP 32bit They're all connected in a "full duplex" manner. What could be the reason? Tried about everything; Stack tracing, recording some actions (like read/write logging).. I want to stress that only the PC I'm not using to code the apps crashes (actually the server app "role" which is running on it - sometimes the game server and sometimes the proxy server). At first I thought that maybe the wireless PC has problems (it's wireless..) but: TCP has it's own mechanisms to make sure the packet is delivered properly. Also, a crash also happens when trying it with the two PCs that are physically connected (Vista vs. XP). Another option is that the Windows DLLs versions might have problems, but then again, one of the tests is Vista vs. Vista, and the other is Vista vs. XP. Any idea?

  Read the article

• FFMPEG Segfault Solutions

  - by Brentley_11

  I'm trying to convert a bunch of movies into h.264 mp4's using FFMPEG. These movies are sourced from various portable camcorders such as the Flip Mino HD and the Kodak ZI8. One issue I'm having with video from the ZI8 is it seems to be causing FFMPEG to segfault. Here is my command: ffmpeg -i 'XmasSailor720p60fps.MOV' -threads 2 -acodec libfaac -ab 96kb -vcodec libx264 -vpre hq -b 500kb -s 484x272 XmasSailor.mp4 Here is the output: FFmpeg version SVN-r20668, Copyright (c) 2000-2009 Fabrice Bellard, et al. built on Dec 2 2009 18:37:34 with gcc 4.2.4 (Ubuntu 4.2.4-1ubuntu4) configuration: --enable-libfaac --enable-libfaad --enable-libmp3lame --enable-libx264 --enable-gpl --enable-nonfree --enable-postproc --enable-pthreads --enable-shared libavutil 50. 5. 1 / 50. 5. 1 libavcodec 52.42. 0 / 52.42. 0 libavformat 52.39. 2 / 52.39. 2 libavdevice 52. 2. 0 / 52. 2. 0 libswscale 0. 7. 2 / 0. 7. 2 libpostproc 51. 2. 0 / 51. 2. 0 Seems stream 0 codec frame rate differs from container frame rate: 59.94 (60000/1001) -> 29.97 (30000/1001) Input #0, mov,mp4,m4a,3gp,3g2,mj2, from 'XmasSailor720p60fps.MOV': Duration: 00:00:05.37, start: 0.000000, bitrate: 12021 kb/s Stream #0.0(eng): Video: h264, yuv420p, 1280x720 [PAR 1:1 DAR 16:9], 11994 kb/s, 29.97 tbr, 90k tbn, 59.94 tbc Stream #0.1(eng): Audio: aac, 48000 Hz, stereo, s16, 128 kb/s Metadata major_brand : qt minor_version : 0 compatible_brands: qt comment : KODAK Zi8 Pocket Video Camera comment-eng : KODAK Zi8 Pocket Video Camera [libx264 @ 0x99e1020]using SAR=1/1 [libx264 @ 0x99e1020]using cpu capabilities: MMX2 SSE2Fast SSSE3 FastShuffle SSE4.1 Cache64 [libx264 @ 0x99e1020]profile High, level 2.1 Output #0, mp4, to 'XmasSailor.mp4': Stream #0.0(eng): Video: libx264, yuv420p, 484x272 [PAR 1:1 DAR 121:68], q=10-51, 500 kb/s, 30k tbn, 29.97 tbc Stream #0.1(eng): Audio: aac, 48000 Hz, stereo, s16, 96 kb/s Metadata comment : Encoded with the Statusfirm Video Transcoder Stream mapping: Stream #0.0 -> #0.0 Stream #0.1 -> #0.1 Press [q] to stop encoding [h264 @ 0x99de950]B picture before any references, skipping [h264 @ 0x99de950]decode_slice_header error [h264 @ 0x99de950]no frame! Error while decoding stream #0.0 [h264 @ 0x99de950]B picture before any references, skipping [h264 @ 0x99de950]decode_slice_header error [h264 @ 0x99de950]no frame! Error while decoding stream #0.0 frame= 20 fps= 0 q=13797729.0 size= 0kB time=0.66 bitrate= 0.6kbits/s frame= 39 fps= 37 q=13797729.0 size= 0kB time=1.30 bitrate= 0.3kbits/s frame= 48 fps= 30 q=33.0 size= 11kB time=0.10 bitrate= 903.0kbits/s frame= 58 fps= 27 q=31.0 size= 22kB time=0.43 bitrate= 421.0kbits/s frame= 67 fps= 25 q=29.0 size= 41kB time=0.73 bitrate= 462.6kbits/s frame= 75 fps= 23 q=29.0 size= 59kB time=1.00 bitrate= 486.7kbits/s frame= 83 fps= 22 q=29.0 size= 81kB time=1.27 bitrate= 521.9kbits/s frame= 90 fps= 21 q=29.0 size= 97kB time=1.50 bitrate= 530.1kbits/s frame= 98 fps= 20 q=29.0 size= 114kB time=1.77 bitrate= 526.9kbits/s frame= 106 fps= 20 q=29.0 size= 134kB time=2.04 bitrate= 537.7kbits/s frame= 114 fps= 19 q=29.0 size= 150kB time=2.30 bitrate= 533.7kbits/s frame= 122 fps= 19 q=29.0 size= 172kB time=2.57 bitrate= 547.8kbits/s frame= 130 fps= 19 q=29.0 size= 193kB time=2.84 bitrate= 557.5kbits/s frame= 136 fps= 18 q=29.0 size= 211kB time=3.04 bitrate= 570.0kbits/s frame= 144 fps= 18 q=29.0 size= 242kB time=3.30 bitrate= 599.5kbits/s frame= 152 fps= 17 q=30.0 size= 261kB time=3.57 bitrate= 598.6kbits/s frame= 157 fps= 15 q=-1.0 Lsize= 368kB time=5.21 bitrate= 579.3kbits/s video:302kB audio:61kB global headers:0kB muxing overhead 1.416371% [libx264 @ 0x99e1020]frame I:1 Avg QP:27.22 size: 8720 [libx264 @ 0x99e1020]frame P:48 Avg QP:25.15 size: 3759 [libx264 @ 0x99e1020]frame B:108 Avg QP:30.10 size: 1105 [libx264 @ 0x99e1020]consecutive B-frames: 0.6% 11.5% 28.8% 59.0% [libx264 @ 0x99e1020]mb I I16..4: 28.5% 47.6% 23.9% [libx264 @ 0x99e1020]mb P I16..4: 0.8% 1.3% 0.5% P16..4: 50.6% 17.7% 13.1% 0.0% 0.0% skip:15.9% [libx264 @ 0x99e1020]mb B I16..4: 0.2% 0.3% 0.1% B16..8: 44.0% 1.2% 2.6% direct: 5.1% skip:46.5% L0:45.5% L1:51.0% BI: 3.5% [libx264 @ 0x99e1020]final ratefactor: 23.51 [libx264 @ 0x99e1020]8x8 transform intra:49.9% inter:67.9% [libx264 @ 0x99e1020]direct mvs spatial:98.1% temporal:1.9% [libx264 @ 0x99e1020]coded y,uvDC,uvAC intra: 54.7% 76.1% 41.4% inter: 17.1% 24.4% 7.8% [libx264 @ 0x99e1020]i16 v,h,dc,p: 18% 52% 5% 25% [libx264 @ 0x99e1020]i8 v,h,dc,ddl,ddr,vr,hd,vl,hu: 12% 22% 9% 7% 10% 10% 9% 8% 13% [libx264 @ 0x99e1020]i4 v,h,dc,ddl,ddr,vr,hd,vl,hu: 13% 18% 8% 8% 10% 13% 10% 9% 12% [libx264 @ 0x99e1020]Weighted P-Frames: Y:10.4% [libx264 @ 0x99e1020]ref P L0: 60.2% 15.3% 11.0% 7.6% 5.2% 0.7% [libx264 @ 0x99e1020]ref B L0: 72.6% 15.6% 11.8% [libx264 @ 0x99e1020]kb/s:471.17 Segmentation fault I'm wondering if anyone else has ran into similar issues. I wasn't able to find anything helpful via Google. Another question I have is if anyone knows of a company that offers paid support for FFMPEG. Thank you for your time.

  Read the article

• C++/msvc6 application crashes due to heap corruption, any hints?

  - by David Alfonso

  Hello all, let me say first that I'm writing this question after months of trying to find out the root of a crash happening in our application. I'll try to detail as much as possible what I've already found out about it. About the application It runs on Windows XP Professional SP2. It's built with Microsoft Visual C++ 6.0 with Service Pack 6. It's MFC based. It uses several external dlls (e.g. Xerces, ZLib or ACE). It has high performance requirements. It does a lot of network and hard disk I/O, but it's also cpu intensive. It has an exception handling mechanism which generates a minidump when an unhandled exception occurs. Facts about the crash It only happens on multiprocessor/multicore machines and under heavy loads of work. It happens at random (neither we nor our client have found a pattern yet). We cannot reproduce the crash on our testing lab. It only happens on some production systems (but always in multicore machines) It always ends up crashing at the same point, although the complete stack is not always the same. Let me add the stack of the crashing thread (obtained using WinDbg, sorry we don't have symbols) ChildEBP RetAddr Args to Child WARNING: Stack unwind information not available. Following frames may be wrong. 030af6c8 7c9206eb 77bfc3c9 01a80000 00224bc3 MyApplication+0x2a85b9 030af960 7c91e9c0 7c92901b 00000ab4 00000000 ntdll!RtlAllocateHeap+0xeac (FPO: [Non-Fpo]) 030af98c 7c9205c8 00000001 00000000 00000000 ntdll!ZwWaitForSingleObject+0xc (FPO: [3,0,0]) 030af9c0 7c920551 01a80898 7c92056d 313adfb0 ntdll!RtlpFreeToHeapLookaside+0x22 (FPO: [2,0,4]) 030afa8c 4ba3ae96 000307da 00130005 00040012 ntdll!RtlFreeHeap+0x1e9 (FPO: [Non-Fpo]) 030afacc 77bfc2e3 0214e384 3087c8d8 02151030 0x4ba3ae96 030afb00 7c91e306 7c80bfc1 00000948 00000001 msvcrt!free+0xc8 (FPO: [Non-Fpo]) 030afb20 0042965b 030afcc0 0214d780 02151218 ntdll!ZwReleaseSemaphore+0xc (FPO: [3,0,0]) 030afb7c 7c9206eb 02e6c471 02ea0000 00000008 MyApplication+0x2965b 030afe60 7c9205c8 02151248 030aff38 7c920551 ntdll!RtlAllocateHeap+0xeac (FPO: [Non-Fpo]) 030afe74 7c92056d 0210bfb8 02151250 02151250 ntdll!RtlpFreeToHeapLookaside+0x22 (FPO: [2,0,4]) 030aff38 77bfc2de 01a80000 00000000 77bfc2e3 ntdll!RtlFreeHeap+0x647 (FPO: [Non-Fpo]) 7c92056d c5ffffff ce7c94be ff7c94be 00ffffff msvcrt!free+0xc3 (FPO: [Non-Fpo]) 7c920575 ff7c94be 00ffffff 12000000 907c94be 0xc5ffffff 7c920579 00ffffff 12000000 907c94be 90909090 0xff7c94be *** WARNING: Unable to verify checksum for xerces-c_2_7.dll *** ERROR: Symbol file could not be found. Defaulted to export symbols for xerces-c_2_7.dll - 7c92057d 12000000 907c94be 90909090 8b55ff8b MyApplication+0xbfffff 7c920581 907c94be 90909090 8b55ff8b 08458bec xerces_c_2_7 7c920585 90909090 8b55ff8b 08458bec 04408b66 0x907c94be 7c920589 8b55ff8b 08458bec 04408b66 0004c25d 0x90909090 7c92058d 08458bec 04408b66 0004c25d 90909090 0x8b55ff8b The address MyApplication+0x2a85b9 corresponds to a call to erase() of a std::list. What I have tried so far Reviewing all the code related to the point where the crash ends happening. Trying to enable pageheap on our testing lab though nothing useful has been found by now. We have substituted the std::list for a C array and then it crashes in other part of the code (although it is related code, it's not in the code where the old list resided). Coincidentally, now it crashes in another erase, though this time of a std::multiset. Let me copy the stack contained in the dump: ntdll.dll!_RtlpCoalesceFreeBlocks@16() + 0x124e bytes ntdll.dll!_RtlFreeHeap@12() + 0x91f bytes msvcrt.dll!_free() + 0xc3 bytes MyApplication.exe!006a4fda() [Frames below may be incorrect and/or missing, no symbols loaded for MyApplication.exe] MyApplication.exe!0069f305() ntdll.dll!_NtFreeVirtualMemory@16() + 0xc bytes ntdll.dll!_RtlpSecMemFreeVirtualMemory@16() + 0x1b bytes ntdll.dll!_ZwWaitForSingleObject@12() + 0xc bytes ntdll.dll!_RtlpFreeToHeapLookaside@8() + 0x26 bytes ntdll.dll!_RtlFreeHeap@12() + 0x114 bytes msvcrt.dll!_free() + 0xc3 bytes c5ffffff() Possible solutions (that I'm aware of) which cannot be applied "Migrate the application to a newer compiler": We are working on this but It's not a solution at the moment. "Enable pageheap (normal or full)": We can't enable pageheap on production machines as this affects performance heavily. I think that's all I remember now, if I have forgotten something I'll add it asap. If you can give me some hint or propose some possible solution, don't hesitate to answer! Thank you in advance for your time and advice.

  Read the article

• Need help identiying a nasty rootkit in Windows

  - by goofrider

  I have a nasty rootkit that not tools seem to be able to idenity. I know for sure it's a rootkit, but I can figure out which rootkit it is. Here's what I gathered so far: It creates multiple copies of itself in %HOME%\Local Settings\Temp with names like Q.EXE, IAJARZ.exe, etc., and install them as hidden services. These EXE have SysInternals identifiers in them so they're definitely rootkits. It hooked very deep in the system, including file read/write, security policies, registry read/write, and possibly WinSock/TCP/IP. When going to Sophos.com to download their software, the rootkit inject something called Microsoft Ajax Tootkit into the page, which injects code into the email submission form in order to redirect it. (EDIT: I might have panicked. Looks like Sophos does use an AJAZ email form, their form is just broken on Chrome so it looked like a mail form injection attack, the link is http://www.sophos.com/en-us/products/free-tools/virus-removal-tool/download.aspx ) Super-Antispyware found a lot of spyware cookies, in the name of .kaspersky.2o7.net, etc. (just chedk 2o7.net, looks like it's a legit ad company) I tried comparing DNS lookup from the infected systems and from system in other physical locations, no DNS redirections it seems. I used dd to copy the MBR and compared it with the MBR provided by ms-sys package, no differences so it's not infecting MBR. No antivirus or rootkit scanner be able to identify it. Most of them can't even find it. I tried scanning, in-situ (normal mode), in safe mode, and boot to linux live CD. Scanners used: Avast, Sophos anti rootkit, Kasersky TDSSKiller, GMER, RootkitRevealer, and many others. Kaspersky reported some unsigned system files that ought to be signed (e.g. tcpip.sys), and reported a number of MD5 mismatches. But otherwise couldn't identify anything based on signature. When running Sysinternal RootkitRevealer and Sophos AntiRootkit, CPU usage goes up to 100% and gets stucked. The Rootkit is blocking them. When trying running/installing HiJackThis, RootkitRevealer and some other scanners, it tells me system security policy prevent running/installing it. The list of malicious acitivities go on and on. here's a sample of logs from all my scans. In particular, aswSnx.SYS, apnenfno.sys and PROCMON20.SYS has a huge number of hooks. It's hard to tell if the rootkit replaced legit program files like aswSnx.SYS (from Avast) and PROCMON20.SYS (from Sysinternal Process Monitor). I can't find whether apnenfno.sys is from a legit program. Help to identify it is appreciated. Trend Micro RootkitBuster ------ [HIDDEN_REGISTRY][Hidden Reg Value]: KeyPath : HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\sptd\Cfg Root : 586bfc0 SubKey : Cfg ValueName : g0 Data : 38 23 E8 D0 BF F2 2D 6F ... ValueType : 3 AccessType: 0 FullLength: 61 DataSize : 32 [HOOKED_SERVICE_API]: Service API : ZwCreateMutant Image Path : C:\WINDOWS\System32\Drivers\aswSnx.SYS OriginalHandler : 0x8061758e CurrentHandler : 0xaa66cce8 ServiceNumber : 0x2b ModuleName : aswSnx.SYS SDTType : 0x0 [HOOKED_SERVICE_API]: Service API : ZwCreateThread Image Path : c:\windows\system32\drivers\apnenfno.sys OriginalHandler : 0x805d1038 CurrentHandler : 0xaa5f118c ServiceNumber : 0x35 ModuleName : apnenfno.sys SDTType : 0x0 [HOOKED_SERVICE_API]: Service API : ZwDeleteKey Image Path : C:\WINDOWS\system32\Drivers\PROCMON20.SYS OriginalHandler : 0x80624472 CurrentHandler : 0xa709b0f8 ServiceNumber : 0x3f ModuleName : PROCMON20.SYS SDTType : 0x0 HiJackThis ------ O23 - Service: JWAHQAGZ - Sysinternals - www.sysinternals.com - C:\DOCUME~1\jeff\LOCALS~1\Temp\JWAHQAGZ.exe O23 - Service: LHIJ - Sysinternals - www.sysinternals.com - C:\DOCUME~1\jeff\LOCALS~1\Temp\LHIJ.exe Kaspersky TDSSKiller ------ 21:05:58.0375 3936 C:\WINDOWS\system32\ati2sgag.exe - copied to quarantine 21:05:59.0217 3936 ATI Smart ( UnsignedFile.Multi.Generic ) - User select action: Quarantine 21:05:59.0342 3936 C:\WINDOWS\system32\BUFADPT.SYS - copied to quarantine 21:05:59.0856 3936 BUFADPT ( UnsignedFile.Multi.Generic ) - User select action: Quarantine 21:05:59.0965 3936 C:\Program Files\CrashPlan\CrashPlanService.exe - copied to quarantine 21:06:00.0152 3936 CrashPlanService ( UnsignedFile.Multi.Generic ) - User select action: Quarantine 21:06:00.0246 3936 C:\WINDOWS\system32\epmntdrv.sys - copied to quarantine 21:06:00.0433 3936 epmntdrv ( UnsignedFile.Multi.Generic ) - User select action: Quarantine 21:06:00.0464 3936 C:\WINDOWS\system32\EuGdiDrv.sys - copied to quarantine 21:06:00.0526 3936 EuGdiDrv ( UnsignedFile.Multi.Generic ) - User select action: Quarantine 21:06:00.0604 3936 C:\Program Files\Common Files\Macrovision Shared\FLEXnet Publisher\FNPLicensingService.exe - copied to quarantine 21:06:01.0181 3936 FLEXnet Licensing Service ( UnsignedFile.Multi.Generic ) - User select action: Quarantine 21:06:01.0321 3936 C:\Program Files\AddinForUNCFAT\UNCFATDMS.exe - copied to quarantine 21:06:01.0430 3936 OTFSDMS ( UnsignedFile.Multi.Generic ) - User select action: Quarantine 21:06:01.0492 3936 C:\WINDOWS\system32\DRIVERS\tcpip.sys - copied to quarantine 21:06:01.0539 3936 Tcpip ( UnsignedFile.Multi.Generic ) - User select action: Quarantine 21:06:01.0601 3936 C:\DOCUME~1\jeff\LOCALS~1\Temp\TULPUWOX.exe - copied to quarantine 21:06:01.0664 3936 HKLM\SYSTEM\ControlSet003\services\TULPUWOX - will be deleted on reboot 21:06:01.0664 3936 C:\DOCUME~1\jeff\LOCALS~1\Temp\TULPUWOX.exe - will be deleted on reboot 21:06:01.0664 3936 TULPUWOX ( UnsignedFile.Multi.Generic ) - User select action: Delete 21:06:01.0757 3936 C:\WINDOWS\system32\Drivers\usbaapl.sys - copied to quarantine 21:06:01.0866 3936 USBAAPL ( UnsignedFile.Multi.Generic ) - User select action: Quarantine 21:06:01.0913 3936 C:\Program Files\VMware\VMware Player\vmware-authd.exe - copied to quarantine 21:06:02.0443 3936 VMAuthdService ( UnsignedFile.Multi.Generic ) - User select action: Quarantine 21:06:02.0443 3936 vmount2 ( UnsignedFile.Multi.Generic ) - skipped by user 21:06:02.0443 3936 vmount2 ( UnsignedFile.Multi.Generic ) - User select action: Skip 21:06:02.0459 3936 vstor2 ( UnsignedFile.Multi.Generic ) - skipped by user 21:06:02.0459 3936 vstor2 ( UnsignedFile.Multi.Generic ) - User select action: Skip

  Read the article

• Making nginx withstand flood attacks

  - by Tiffany Walker

  How can I make it stand stand against attacks better? Are their plugins. Looking for a way to RATE LIMIT and remain up and not slow down. My Setup: user nobody; # no need for more workers in the proxy mode worker_processes 4; worker_cpu_affinity 0001 0010 0100 1000; worker_priority -2; error_log /var/log/nginx/error.log info; worker_rlimit_nofile 40480; events { worker_connections 5120; # increase for busier servers use epoll; # you should use epoll here for Linux kernels 2.6.x } http { server_name_in_redirect off; server_names_hash_max_size 10240; server_names_hash_bucket_size 1024; include mime.types; default_type application/octet-stream; server_tokens off; disable_symlinks if_not_owner; sendfile on; tcp_nopush on; tcp_nodelay on; keepalive_timeout 5; gzip on; gzip_vary on; gzip_disable "MSIE [1-6]\."; gzip_proxied any; gzip_http_version 1.1; gzip_min_length 1000; gzip_comp_level 9; gzip_buffers 16 8k; # You can remove image/png image/x-icon image/gif image/jpeg if you have slow CPU gzip_types text/plain text/xml text/css application/x-javascript application/xml image/png image/x-icon image/gif image/jpeg application/xml+rss text/javascript application/atom+xml; ignore_invalid_headers on; client_header_timeout 3m; client_body_timeout 3m; send_timeout 3m; reset_timedout_connection on; connection_pool_size 256; client_header_buffer_size 256k; large_client_header_buffers 4 256k; client_max_body_size 200M; client_body_buffer_size 128k; request_pool_size 32k; output_buffers 4 32k; postpone_output 1460; proxy_temp_path /tmp/nginx_proxy/; client_body_in_file_only on; log_format bytes_log "$msec $bytes_sent ."; include "/etc/nginx/vhosts/*"; } vhost file: server { error_log /var/log/nginx/vhost-error_log warn; listen 194.145.208.19:80; server_name ipxnow.in www.ipxnow.in; access_log /usr/local/apache/domlogs/ipxnow.in-bytes_log bytes_log; access_log /usr/local/apache/domlogs/ipxnow.in combined; root /home/ipxnowin/public_html; location / { location ~.*\.(3gp|gif|jpg|jpeg|png|ico|wmv|avi|asf|asx|mpg|mpeg|mp4|pls|mp3|mid|wav|swf|flv|html|htm|txt|js|css|exe|zip|tar|rar|gz|tgz|bz2|uha|7z|doc|docx|xls|xlsx|pdf|iso)$ { expires 7d; try_files $uri @backend; } error_page 405 = @backend; add_header X-Cache "HIT from Backend"; proxy_pass http://194.145.208.19:8081; include proxy.inc; } location @backend { internal; proxy_pass http://194.145.208.19:8081; include proxy.inc; } location ~ .*\.(php|jsp|cgi|pl|py)?$ { proxy_pass http://194.145.208.19:8081; include proxy.inc; } location ~ /\.ht { deny all; } } and proxy.inc: proxy_connect_timeout 59s; proxy_send_timeout 600; proxy_read_timeout 600; proxy_buffer_size 64k; proxy_buffers 16 32k; proxy_busy_buffers_size 64k; proxy_temp_file_write_size 64k; proxy_pass_header Set-Cookie; proxy_redirect off; proxy_hide_header Vary; proxy_set_header Accept-Encoding ''; proxy_ignore_headers Cache-Control Expires; proxy_set_header Referer $http_referer; proxy_set_header Host $host; proxy_set_header Cookie $http_cookie; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-Host $host; proxy_set_header X-Forwarded-Server $host; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for;

  Read the article

• FFmpeg creates emtpy (black) frames

  - by resamsel

  I have a set of images from a timelapse shot (172 JPG files) that I want to convert into a movie. I tried several parameters with FFmpeg, but all I get is a video with black frames (though it has the expected length). ffmpeg -f image2 -vcodec mjpeg -y -i img_%03d.jpg timelapse2.mpg The command above creates this video: http://sdm-net.org/data/timelapse2.mpg What I'm expecting is something like this (created with Time Lapse Assembler.app): https://vimeo.com/39038362 - This is my fallback option, but I'd really like to create timelapse movies from a script. I'm on OSX Lion (10.7.3) with FFmpeg version (0.10) installed via Homebrew. I also tried to find a proper version of mencoder for OSX, but this doesn't seem to be an easy task. Also, ImageMagick's convert doesn't seem to work nicely, it creates really bad output and it seems there's not much I can do about it... Edit: With libx264 and an mp4 container: ffmpeg -f image2 -y -i img_%03d.jpg -vcodec libx264 timelapse4.mp4 Output: ffmpeg version 0.10 Copyright (c) 2000-2012 the FFmpeg developers built on Mar 26 2012 13:47:02 with clang 3.0 (tags/Apple/clang-211.12) configuration: --prefix=/usr/local/Cellar/ffmpeg/0.10 --enable-shared --enable-gpl --enable-version3 --enable-nonfree --enable-hardcoded-tables --enable-libfreetype --cc=/usr/bin/clang --enable-libx264 --enable-libfaac --enable-libmp3lame --enable-librtmp --enable-libtheora --enable-libvorbis --enable-libvpx --enable-libxvid --enable-libopencore-amrnb --enable-libopencore-amrwb --enable-libass --disable-ffplay libavutil 51. 34.101 / 51. 34.101 libavcodec 53. 60.100 / 53. 60.100 libavformat 53. 31.100 / 53. 31.100 libavdevice 53. 4.100 / 53. 4.100 libavfilter 2. 60.100 / 2. 60.100 libswscale 2. 1.100 / 2. 1.100 libswresample 0. 6.100 / 0. 6.100 libpostproc 52. 0.100 / 52. 0.100 Input #0, image2, from 'img_%03d.jpg': Duration: 00:00:06.88, start: 0.000000, bitrate: N/A Stream #0:0: Video: mjpeg, yuvj420p, 3888x2592 [SAR 72:72 DAR 3:2], 25 fps, 25 tbr, 25 tbn, 25 tbc [buffer @ 0x7f8ec9415f20] w:3888 h:2592 pixfmt:yuvj420p tb:1/1000000 sar:72/72 sws_param: [libx264 @ 0x7f8ec981d800] using SAR=1/1 [libx264 @ 0x7f8ec981d800] frame MB size (243x162) > level limit (36864) [libx264 @ 0x7f8ec981d800] MB rate (984150) > level limit (983040) [libx264 @ 0x7f8ec981d800] using cpu capabilities: MMX2 SSE2Fast SSSE3 FastShuffle SSE4.2 AVX [libx264 @ 0x7f8ec981d800] profile High, level 5.1 [libx264 @ 0x7f8ec981d800] 264 - core 120 - H.264/MPEG-4 AVC codec - Copyleft 2003-2011 - http://www.videolan.org/x264.html - options: cabac=1 ref=3 deblock=1:0:0 analyse=0x3:0x113 me=hex subme=7 psy=1 psy_rd=1.00:0.00 mixed_ref=1 me_range=16 chroma_me=1 trellis=1 8x8dct=1 cqm=0 deadzone=21,11 fast_pskip=1 chroma_qp_offset=-2 threads=12 sliced_threads=0 nr=0 decimate=1 interlaced=0 bluray_compat=0 constrained_intra=0 bframes=3 b_pyramid=2 b_adapt=1 b_bias=0 direct=1 weightb=1 open_gop=0 weightp=2 keyint=250 keyint_min=25 scenecut=40 intra_refresh=0 rc_lookahead=40 rc=crf mbtree=1 crf=23.0 qcomp=0.60 qpmin=0 qpmax=69 qpstep=4 ip_ratio=1.40 aq=1:1.00 Output #0, mp4, to 'timelapse4.mp4': Metadata: encoder : Lavf53.31.100 Stream #0:0: Video: h264 (![0][0][0] / 0x0021), yuvj420p, 3888x2592 [SAR 72:72 DAR 3:2], q=-1--1, 25 tbn, 25 tbc Stream mapping: Stream #0:0 -> #0:0 (mjpeg -> libx264) Press [q] to stop, [?] for help frame= 172 fps= 18 q=-1.0 Lsize= 259kB time=00:00:06.80 bitrate= 312.3kbits/s video:256kB audio:0kB global headers:0kB muxing overhead 1.089647% [libx264 @ 0x7f8ec981d800] frame I:1 Avg QP: 9.60 size:212820 [libx264 @ 0x7f8ec981d800] frame P:43 Avg QP:30.50 size: 291 [libx264 @ 0x7f8ec981d800] frame B:128 Avg QP:31.00 size: 285 [libx264 @ 0x7f8ec981d800] consecutive B-frames: 0.6% 0.0% 1.7% 97.7% [libx264 @ 0x7f8ec981d800] mb I I16..4: 22.5% 77.2% 0.3% [libx264 @ 0x7f8ec981d800] mb P I16..4: 0.0% 0.0% 0.0% P16..4: 0.0% 0.0% 0.0% 0.0% 0.0% skip:100.0% [libx264 @ 0x7f8ec981d800] mb B I16..4: 0.0% 0.0% 0.0% B16..8: 0.0% 0.0% 0.0% direct: 0.0% skip:100.0% L0: 1.2% L1:98.8% BI: 0.0% [libx264 @ 0x7f8ec981d800] 8x8 transform intra:77.2% inter:100.0% [libx264 @ 0x7f8ec981d800] coded y,uvDC,uvAC intra: 41.2% 23.4% 0.6% inter: 0.0% 0.0% 0.0% [libx264 @ 0x7f8ec981d800] i16 v,h,dc,p: 40% 25% 35% 1% [libx264 @ 0x7f8ec981d800] i8 v,h,dc,ddl,ddr,vr,hd,vl,hu: 36% 32% 30% 1% 0% 0% 0% 0% 0% [libx264 @ 0x7f8ec981d800] i4 v,h,dc,ddl,ddr,vr,hd,vl,hu: 51% 40% 6% 1% 1% 0% 1% 0% 1% [libx264 @ 0x7f8ec981d800] i8c dc,h,v,p: 60% 21% 19% 0% [libx264 @ 0x7f8ec981d800] Weighted P-Frames: Y:0.0% UV:0.0% [libx264 @ 0x7f8ec981d800] ref P L0: 92.3% 0.0% 0.0% 7.7% [libx264 @ 0x7f8ec981d800] ref B L0: 50.0% 0.0% 50.0% [libx264 @ 0x7f8ec981d800] ref B L1: 99.4% 0.6% [libx264 @ 0x7f8ec981d800] kb/s:304.49 Output timelapse4.mp4 (beacause of spam protection I can only post two links with my reputation): http sdm-net.org/data/timelapse4.mp4

  Read the article

• ESXi v5.5 is having random crashes

  - by Darkmage

  HW: Type: HP Proliant ML350 G5 RAM 22GB CPU 1 x Intel Xenon E5405 2.00GHz OP: ESXi 5.5 just updated from 5.1 to try and fix the crashes occurring on ESXi 5.1 on same hardware. I'm trying to find the error on why one of our servers is crashing, it has had two lock ups in 24 hours now. The internal error light on the front is blinking red, on the inside only "#5 and #6 page 76 manual" the "Processor 2" light "amber" and the "Power" light "green" is shining. in the logs the only errors i can see in the relevant time frame is in log under. Is this the reason? or is there anything else i can do to try and log/locate the error. from zcat syslog.6.gz | less 2014-05-26T11:55:47Z sfcbd[35064]: Error opening socket pair for getProviderContext: Too many open files 2014-05-26T11:55:47Z sfcbd[35064]: Failed to set recv timeout (30) for socket -1. Errno = 9 2014-05-26T11:55:47Z sfcbd[35064]: Failed to set timeout for local socket (e.g. provider) 2014-05-26T11:55:47Z sfcbd[35064]: spGetMsg receiving from -1 35064-9 Bad file descriptor 2014-05-26T11:55:47Z sfcbd[35064]: rcvMsg receiving from -1 35064-9 Bad file descriptor 2014-05-26T11:55:47Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:55:47Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:55:47Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:55:47Z sfcbd[35064]: Error opening socket pair for getProviderContext: Too many open files 2014-05-26T11:55:47Z sfcbd[35064]: Failed to set recv timeout (30) for socket -1. Errno = 9 2014-05-26T11:55:47Z sfcbd[35064]: Failed to set timeout for local socket (e.g. provider) 2014-05-26T11:55:47Z sfcbd[35064]: spGetMsg receiving from -1 35064-9 Bad file descriptor 2014-05-26T11:55:47Z sfcbd[35064]: rcvMsg receiving from -1 35064-9 Bad file descriptor 2014-05-26T11:55:47Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:55:47Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:55:47Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:55:53Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:55:57Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:01Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:04Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:15Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:17Z sfcbd[35064]: Error opening socket pair for getProviderContext: Too many open files 2014-05-26T11:56:17Z sfcbd[35064]: Failed to set recv timeout (30) for socket -1. Errno = 9 2014-05-26T11:56:17Z sfcbd[35064]: Failed to set timeout for local socket (e.g. provider) 2014-05-26T11:56:17Z sfcbd[35064]: spGetMsg receiving from -1 35064-9 Bad file descriptor 2014-05-26T11:56:17Z sfcbd[35064]: rcvMsg receiving from -1 35064-9 Bad file descriptor 2014-05-26T11:56:17Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:17Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:17Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:17Z sfcbd[35064]: Error opening socket pair for getProviderContext: Too many open files 2014-05-26T11:56:17Z sfcbd[35064]: Failed to set recv timeout (30) for socket -1. Errno = 9 2014-05-26T11:56:17Z sfcbd[35064]: Failed to set timeout for local socket (e.g. provider) 2014-05-26T11:56:17Z sfcbd[35064]: spGetMsg receiving from -1 35064-9 Bad file descriptor 2014-05-26T11:56:17Z sfcbd[35064]: rcvMsg receiving from -1 35064-9 Bad file descriptor 2014-05-26T11:56:17Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:17Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:17Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:23Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:27Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:31Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:34Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:34Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:34Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:34Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:34Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:44Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:44Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:44Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:44Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:46Z sfcb-ProviderManager[34828]: SendMsg sending to 1 34828-9 Bad file descriptor 2014-05-26T11:56:48Z sfcbd[35064]: Error opening socket pair for getProviderContext: Too many open files -- manual

  Read the article

• Windows 8, NVIDIA graphics recognition fails

  - by Roy Grubb

  I just installed Windows 8 Pro OEM 64-bit (clean install) and it won't properly recognize my graphics adapter. When I installed Win8, it automatically installed the BasicDisplay.sys driver dated 6/21/2006. 6.2.9200.16384 (win8_rtm.120725-1247). Hardware - Mobo:MSi G41M-P33 Combo CPU:Intel CoreDuo 6600 Graphics:NVIDIA GeForce 9400GT *OS* - Windows 8 Pro 64-bit OEM The graphics adapter worked fine in Windows XP. The PC is a generic box, bought locally and its mobo failed recently, so I replaced it with the G41M. Microsoft wouldn't let me re-activate Windows XP with a different mobo, so I installed Win8, which appears to work except as described next. Win8 only partially recognizes the graphics adapter and won't allow NVIDIA latest driver installer to see that it's an NVIDIA card. As a result, OpenGL doesn't work, and this is needed by the software I most use. Other than that the graphics look OK. When I say 'partially recognizes', I mean that via the Control Panel, I can see that the adapter is described as NVIDIA, but the driver remains stuck at Microsoft Basic Display Adapter no matter what I try, including "Update driver..." in adapter properties. Display Screen Resolution Advanced Settings Adapter shows: Adapter Type: Microsoft Basic Display Adapter Chip Type: NVIDIA DAC Type: NVIDIA Corporation Bios Information: G27 Board - p381n17 Don't know what this means ... no mention of 9400GT Total Available Graphics Memory: 256 MB Dedicated Video Memory: 0 MB In fact the adapter has 512MB on-board video memory. System Video Memory: 0 MB Shared System Memory: 256 MB And Control Panel Device Manager Display adapters just shows Microsoft Basic Display Adapter. No other graphics adapter, and no unknown device or yellow question mark. What I have tried so far: 1. Cleared CMOS and reset. Updated BIOS and all mobo drivers as follows: 1st I used Driver Reviver to see if any driver updates were required. It found some but I didn't use that to get the drivers. Then I switched to MSi's own mobo driver utility Live Update 5. This also showed the board needed to update several so I used it to fetch the new drivers. After that it showed that everything was up to date and I checked with Driver Reviver again, which also reported no drivers now needed updating. Rebooted. Went to the NVIDIA site to get the latest graphics adapter driver. Their auto-detect "Option 2: Automatically find drivers for my NVIDIA products" said "The NVIDIA Smart Scan was unable to evaluate your system hardware. Please use Option 1 to manually find drivers for your NVIDIA products." So I downloaded 310.70-desktop-win8-win7-winvista-64bit-international-whql.exe, which lists 9400 GT under supported products, but when I run it, it says: "NVIDIA Installer cannot continue This graphics driver could not find compatible graphics hardware." Connected the display to the on-board Intel graphics (G41 Intel Express), removed the NVIDIA card and rebooted, changed to internal graphics in CMOS. Again it installs the MS Basic Display Adapter, and can't properly run my s/w that needs OpenGL. It runs on other machines with Intel Express graphics (WinXP and 7) Shut down and pulled out the power cord. Held start button to discharge all capacitors. Removed and re-inserted NVIDIA adapter in PCI-E slot and made sure properly seated. Connected the monitor to the card, screwed plug to socket. Reconnected power cord. Started and checked in BIOS that Primary Graphics Adapter was set to PCI-E. Started Windows. Uninstalled MS Basic Display Adapter in Device Manager. Screen blanks briefly, reappears. No Graphics adapter entry was then visible in Device Manager. Restarted PC. MS Basic Display Adapter Visible again in Device Manager. Clicked in Device Manager View Show hidden devices. No other graphics adapter appears, no unknown devices. Rebooted. Tried Scan for Hardware changes. None detected. Tried right-click on MS Basic Display Adapter Properties Driver Update Driver... Search automatically. It replied that it had determined driver was up to date. I checked that there were no graphic driver-related entries in Programs and Features that I could delete (none). Searched for any other drivers with nvidia in their name and deleted them, just keeping the 306.97 installer exe file. Did a Windows Update. Ran GPU-Z which shows (main items): Microsoft Basic Display Adapter GPU G72 BIOS 5.72.22.76.88 Device ID 10DE - 01D5 DDR2 Bus Width 32 Bit Memory size 64MB Driver Version nvlddmkm 6.2.9200.16384 (ForceWare 0.00) / Win8 64 NVIDIA SLI Unknown in the drop-down at the foot, "Microsoft Basic Display Adapter" is the only option If I swap hard disks in that machine to one with a Ubuntu 10.4 installation (originally installed on the same PC), lspci shows "VGA compatible controller as NVIDIA Corporation Device 01d5 (rev a1) (prog-if 00 [VGA controller])" and "kernel driver in use: nvidia" I'm out of ideas for new things to try and would be really grateful of suggestions. Thanks!

  Read the article

• Nginx reverse proxy IP issue

  - by Tiffany Walker

  For some reason Apache is still seeing my SERVERS ip. Is this an nginx problem? /etc/nginx.conf user nobody; # no need for more workers in the proxy mode worker_processes 4; error_log /var/log/nginx/error.log info; worker_rlimit_nofile 20480; events { worker_connections 5120; # increase for busier servers use epoll; # you should use epoll here for Linux kernels 2.6.x } http { server_name_in_redirect off; server_names_hash_max_size 10240; server_names_hash_bucket_size 1024; include mime.types; default_type application/octet-stream; server_tokens off; disable_symlinks if_not_owner; sendfile on; tcp_nopush on; tcp_nodelay on; keepalive_timeout 5; gzip on; gzip_vary on; gzip_disable "MSIE [1-6]\."; gzip_proxied any; gzip_http_version 1.1; gzip_min_length 1000; gzip_comp_level 6; gzip_buffers 16 8k; # You can remove image/png image/x-icon image/gif image/jpeg if you have slow CPU gzip_types text/plain text/xml text/css application/x-javascript application/xml image/png image/x-icon image/gif image/jpeg application/xml+rss text/javascript application/atom+xml; ignore_invalid_headers on; client_header_timeout 3m; client_body_timeout 3m; send_timeout 3m; reset_timedout_connection on; connection_pool_size 256; client_header_buffer_size 256k; large_client_header_buffers 4 256k; client_max_body_size 200M; client_body_buffer_size 128k; request_pool_size 32k; output_buffers 4 32k; postpone_output 1460; proxy_temp_path /tmp/nginx_proxy/; client_body_in_file_only on; log_format bytes_log "$msec $bytes_sent ."; include "/etc/nginx/vhosts/*"; } proxy.inc proxy_connect_timeout 59s; proxy_send_timeout 600; proxy_read_timeout 600; proxy_buffer_size 64k; proxy_buffers 16 32k; proxy_busy_buffers_size 64k; proxy_temp_file_write_size 64k; proxy_pass_header Set-Cookie; proxy_redirect off; proxy_hide_header Vary; proxy_set_header Accept-Encoding ''; proxy_ignore_headers Cache-Control Expires; proxy_set_header Referer $http_referer; proxy_set_header Host $host; proxy_set_header Cookie $http_cookie; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-Host $host; proxy_set_header X-Forwarded-Server $host; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; vhost file: server { error_log /var/log/nginx/vhost-error_log warn; listen 63.6.1.12:80; server_name photo-rolldomain.com www.domain.com; access_log /usr/local/apache/domlogs/domain.com-bytes_log bytes_log; access_log /usr/local/apache/domlogs/domain.com combined; root /home/mtech/public_html; location / { location ~.*\.(3gp|gif|jpg|jpeg|png|ico|wmv|avi|asf|asx|mpg|mpeg|mp4|pls|mp3|mid|wav|swf|flv|html|htm|txt|js|css|exe|zip|tar|rar|gz|tgz|bz2|uha|7z|doc|docx|xls|xlsx|pdf|iso)$ { expires 7d; try_files $uri @backend; } error_page 405 = @backend; add_header X-Cache "HIT from Backend"; proxy_pass http://63.6.1.12:8081; include proxy.inc; } location @backend { internal; proxy_pass http://63.6.1.12:8081; include proxy.inc; } location ~ .*\.(php|jsp|cgi|pl|py)?$ { proxy_pass http://63.6.1.12:8081; include proxy.inc; } location ~ /\.ht { deny all; } }

  Read the article

• Windows XP - Repairing Corrupt System32\Config\System File

  - by SimonTewsi

  My apologies for this long post. I would like to describe the mess I'm in then ask some questions about how to fix it: Starting up my Windows XP SP1 machine I got the following message: Windows could not start because the following file is missing or corrupt: \WINDOWS\SYSTEM32\CONFIG\SYSTEM Tried restarting several times with same results then Googled the problem. Tried the fix described here: http://icrontic.com/articles/repair%5Fwindows%5Fxp (since my CPU does not have XD buffer overflow protection I did not set /NOEXECUTE=OPTIN as OS Load Option). This did not work. I then found another fix for the problem on hardwareanalysis.com: Basically, boot to dos prompt (or recovery console if available) and make backups of the following files:- c:\windows\system32\config\system (to c:\windows\tmp\system.bak) c:\windows\system32\config\software (to c:\windows\tmp\software.bak) c:\windows\system32\config\sam (to c:\windows\tmp\sam.bak) c:\windows\system32\config\security (to c:\windows\tmp\security.bak) c:\windows\system32\config\default (to c:\windows\tmp\default.bak) then delete the above files (not the backups!) then copy the above files in c:\windows\repair to the c:\windows\system32\config directory restart your computer This did work (and I wish I'd done it first, since it was completely reversible, unlike the first method). However, afterwards I found that all the user accounts on the PC were gone. I resurrected them by copying the backed up security file back into the system32\config folder (I may have copied the SAM file from backup as well, I cannot remember clearly now). Now the PC boots up and I can log in. However things are still not right. I tried to alter one of the user accounts and found I could not access the User Accounts in the Control Panel. Microsoft KB 919292 had a fix for the problem. However, the fix failed with a Windows Installer error: The Windows Installer Service could not be accessed. This can occur if you are running Windows in safe mode, or if Windows Installer is not correctly installed. Contact your support personnel for assistance. Windows Installer 3.1 was already installed. I reinstalled it but continued to get the Windows Installer error whenever I tried to run the fix in KB 919292. I have since noticed another three problems: 1) Several applications on the PC no longer run, eg Microsoft Word. Shortcuts no longer seem to do anything and if I run the executables directly (eg for Word by running C:\Program Files\Microsoft Office\Office10\Winword.exe) I get a message similar to: "Microsoft Word has not been installed for the current user. Please run setup to install the application." even though the executable is clearly visible in Windows Explorer (and even though Word actually opens - the error dialog appears after Word has opened. Clicking OK to the error dialog closes Word). 2) One or the other of the two fixes I tried for the original problem caused new user profiles to be created. eg My old user profile under the Documents and Settings folder was Simon. The old one still exists but there is now a new one called Simon.DBQ2515. Obviously the new one is being used because Opera (my browser that still works) no longer sees the bookmarks file under my old profile. 3) Probably as a result of fooling around with the Security file, when I try to boot off the Windows XP CD and run the Recovery Console I am now asked for the administrator password. The only problem is there is no administrator account on the PC. There is one account, LocalAdmin, that has administrative rights but when I entered the password for that account it did not work. It is so long since I originally set up the PC that I cannot remember if the original administrator account ever had a password and, if so, what it was. So, my question is: How can I fix this mess? In particular: 1) Having tried the two fixes linked to above, have I irrepairably damaged the Windows instance, requiring a clean reinstallation of Windows + all applications, or should it be possible to get the machine working correctly again without such drastic measures? 2) Is there any way to get around the administrator password so I can use the Recovery Console again, given that there is no account called "administrator" and the password for the one account with admin privileges does not work (and that, before I started the second fix, I was not asked for an administrator password)? 3) Is there any easy way to fix the problem with the applications that think they are not installed? 4) Is there any easy way to fix the problem of the Windows Installer that does not work, even if reinstalled? Cheers Simon

  Read the article

• Strange performance behaviour for 64 bit modulo operation

  - by codymanix

  The last three of these method calls take approx. double the time than the first four. The only difference is that their arguments doesn't fit in integer anymore. But should this matter? The parameter is declared to be long, so it should use long for calculation anyway. Does the modulo operation use another algorithm for numbersmaxint? I am using amd athlon64 3200+, winxp sp3 and vs2008. Stopwatch sw = new Stopwatch(); TestLong(sw, int.MaxValue - 3l); TestLong(sw, int.MaxValue - 2l); TestLong(sw, int.MaxValue - 1l); TestLong(sw, int.MaxValue); TestLong(sw, int.MaxValue + 1l); TestLong(sw, int.MaxValue + 2l); TestLong(sw, int.MaxValue + 3l); Console.ReadLine(); static void TestLong(Stopwatch sw, long num) { long n = 0; sw.Reset(); sw.Start(); for (long i = 3; i < 20000000; i++) { n += num % i; } sw.Stop(); Console.WriteLine(sw.Elapsed); } EDIT: I now tried the same with C and the issue does not occur here, all modulo operations take the same time, in release and in debug mode with and without optimizations turned on: #include "stdafx.h" #include "time.h" #include "limits.h" static void TestLong(long long num) { long long n = 0; clock_t t = clock(); for (long long i = 3; i < 20000000LL*100; i++) { n += num % i; } printf("%d - %lld\n", clock()-t, n); } int main() { printf("%i %i %i %i\n\n", sizeof (int), sizeof(long), sizeof(long long), sizeof(void*)); TestLong(3); TestLong(10); TestLong(131); TestLong(INT_MAX - 1L); TestLong(UINT_MAX +1LL); TestLong(INT_MAX + 1LL); TestLong(LLONG_MAX-1LL); getchar(); return 0; } EDIT2: Thanks for the great suggestions. I found that both .net and c (in debug as well as in release mode) does't not use atomically cpu instructions to calculate the remainder but they call a function that does. In the c program I could get the name of it which is "_allrem". It also displayed full source comments for this file so I found the information that this algorithm special cases the 32bit divisors instead of dividends which was the case in the .net application. I also found out that the performance of the c program really is only affected by the value of the divisor but not the dividend. Another test showed that the performance of the remainder function in the .net program depends on both the dividend and divisor. BTW: Even simple additions of long long values are calculated by a consecutive add and adc instructions. So even if my processor calls itself 64bit, it really isn't :( EDIT3: I now ran the c app on a windows 7 x64 edition, compiled with visual studio 2010. The funny thing is, the performance behavior stays the same, although now (I checked the assembly source) true 64 bit instructions are used.

  Read the article

• Screen Casting using ffmpeg (too fast)

  - by rowman

  I can use ffmpeg to make screen casts: ffmpeg -f x11grab -s 1280x800 -i :0.0 -c:v libx264 -framerate 30 -r 30 -crf 18 out.mkv However the output comes out to be too fast paced. It also happens with GTK RecordMyDesktop if I enable the encode on the fly. So, the questions is how to get a normal video pace. Also in order to capture the sound with ffmpeg what option should be used? FFmpeg Output: ffmpeg -f x11grab -s 1280x800 -r 30 -i :0.0 -c:v libx264 -framerate 30 -r 30 -crf 18 out.mkv ffmpeg version N-35162-g87244c8 Copyright (c) 2000-2012 the FFmpeg developers built on Oct 7 2012 15:56:19 with gcc 4.6 (Ubuntu/Linaro 4.6.3-1ubuntu5) configuration: --enable-gpl --enable-libfaac --enable-libfdk-aac --enable-libmp3lame --enable-libopencore-amrnb --enable-libopencore-amrwb --enable-librtmp --enable-libtheora --enable-libvorbis --enable-libvpx --enable-x11grab --enable-libx264 --enable-nonfree --enable-version3 libavutil 51. 73.102 / 51. 73.102 libavcodec 54. 64.100 / 54. 64.100 libavformat 54. 29.105 / 54. 29.105 libavdevice 54. 3.100 / 54. 3.100 libavfilter 3. 19.102 / 3. 19.102 libswscale 2. 1.101 / 2. 1.101 libswresample 0. 16.100 / 0. 16.100 libpostproc 52. 1.100 / 52. 1.100 [x11grab @ 0xab896a0] device: :0.0 -> display: :0.0 x: 0 y: 0 width: 1280 height: 800 [x11grab @ 0xab896a0] shared memory extension found [x11grab @ 0xab896a0] Estimating duration from bitrate, this may be inaccurate Input #0, x11grab, from ':0.0': Duration: N/A, start: 1350136942.608988, bitrate: 983040 kb/s Stream #0:0: Video: rawvideo (BGR[0] / 0x524742), bgr0, 1280x800, 983040 kb/s, 30 tbr, 1000k tbn, 30 tbc [libx264 @ 0xab87320] using cpu capabilities: MMX2 SSE2Fast SSSE3 Cache64 SlowCTZ SlowAtom [libx264 @ 0xab87320] profile High 4:4:4 Predictive, level 3.2, 4:4:4 8-bit [libx264 @ 0xab87320] 264 - core 128 r2 198a7ea - H.264/MPEG-4 AVC codec - Copyleft 2003-2012 - http://www.videolan.org/x264.html - options: cabac=1 ref=3 deblock=1:0:0 analyse=0x3:0x113 me=hex subme=7 psy=1 psy_rd=1.00:0.00 mixed_ref=1 me_range=16 chroma_me=1 trellis=1 8x8dct=1 cqm=0 deadzone=21,11 fast_pskip=1 chroma_qp_offset=4 threads=6 lookahead_threads=1 sliced_threads=0 nr=0 decimate=1 interlaced=0 bluray_compat=0 constrained_intra=0 bframes=3 b_pyramid=2 b_adapt=1 b_bias=0 direct=1 weightb=1 open_gop=0 weightp=2 keyint=250 keyint_min=25 scenecut=40 intra_refresh=0 rc_lookahead=40 rc=crf mbtree=1 crf=18.0 qcomp=0.60 qpmin=0 qpmax=69 qpstep=4 ip_ratio=1.40 aq=1:1.00 Output #0, matroska, to 'out.mkv': Metadata: encoder : Lavf54.29.105 Stream #0:0: Video: h264, yuv444p, 1280x800, q=-1--1, 1k tbn, 30 tbc Stream mapping: Stream #0:0 -> #0:0 (rawvideo -> libx264) Press [q] to stop, [?] for help frame= 10 fps=0.0 q=0.0 size= 1kB time=00:00:00.00 bitrate= 0.0kbits/sframe= 19 fps= 17 q=0.0 size= 1kB time=00:00:00.00 bitrate= 0.0kbits/sframe= 28 fps= 17 q=0.0 size= 1kB time=00:00:00.00 bitrate= 0.0kbits/sframe= 37 fps= 17 q=0.0 size= 1kB time=00:00:00.00 bitrate= 0.0kbits/sframe= 45 fps= 16 q=0.0 size= 1kB time=00:00:00.00 bitrate= 0.0kbits/sframe= 47 fps= 14 q=0.0 size= 1kB time=00:00:00.00 bitrate= 0.0kbits/sframe= 52 fps= 13 q=24.0 size= 257kB time=00:00:00.00 bitrate=2101632.0kbiframe= 55 fps= 12 q=24.0 size= 257kB time=00:00:00.10 bitrate=20808.2kbitsframe= 59 fps= 11 q=24.0 size= 289kB time=00:00:00.23 bitrate=10145.0kbitsframe= 64 fps= 11 q=24.0 size= 289kB time=00:00:00.40 bitrate=5894.7kbits/frame= 70 fps= 11 q=24.0 size= 289kB time=00:00:00.60 bitrate=3933.1kbits/frame= 72 fps= 10 q=24.0 size= 289kB time=00:00:00.66 bitrate=3549.2kbits/frame= 77 fps=9.8 q=24.0 size= 289kB time=00:00:00.83 bitrate=2837.7kbits/frame= 80 fps=9.6 q=24.0 size= 289kB time=00:00:00.93 bitrate=2533.5kbits/frame= 85 fps=9.3 q=24.0 size= 289kB time=00:00:01.10 bitrate=2146.9kbits/frame= 89 fps=9.3 q=24.0 size= 289kB time=00:00:01.23 bitrate=1917.1kbits/frame= 92 fps=9.1 q=24.0 size= 289kB time=00:00:01.33 bitrate=1773.3kbits/frame= 96 fps=9.0 q=24.0 size= 289kB time=00:00:01.46 bitrate=1612.4kbits/frame= 99 fps=8.8 q=24.0 size= 321kB time=00:00:01.56 bitrate=1676.8kbits/frame= 104 fps=8.7 q=24.0 size= 321kB time=00:00:01.73 bitrate=1515.2kbits/frame= 109 fps=5.3 q=24.0 Lsize= 1093kB time=00:00:03.56 bitrate=2511.5kbits/s video:1092kB audio:0kB subtitle:0 global headers:0kB muxing overhead 0.120198% [libx264 @ 0xab87320] frame I:3 Avg QP:18.93 size:142610 [libx264 @ 0xab87320] frame P:43 Avg QP:20.79 size: 15751 [libx264 @ 0xab87320] frame B:63 Avg QP:23.75 size: 195 [libx264 @ 0xab87320] consecutive B-frames: 21.1% 1.8% 11.0% 66.1% [libx264 @ 0xab87320] mb I I16..4: 50.0% 21.1% 28.9% [libx264 @ 0xab87320] mb P I16..4: 6.1% 0.9% 3.2% P16..4: 5.5% 1.2% 0.6% 0.0% 0.0% skip:82.5% [libx264 @ 0xab87320] mb B I16..4: 0.4% 0.1% 0.0% B16..8: 2.9% 0.1% 0.0% direct: 0.0% skip:96.5% L0:40.7% L1:57.0% BI: 2.3% [libx264 @ 0xab87320] 8x8 transform intra:14.5% inter:46.1% [libx264 @ 0xab87320] coded y,u,v intra: 33.5% 24.1% 25.4% inter: 0.9% 0.4% 0.4% [libx264 @ 0xab87320] i16 v,h,dc,p: 70% 26% 1% 3% [libx264 @ 0xab87320] i8 v,h,dc,ddl,ddr,vr,hd,vl,hu: 11% 21% 30% 5% 7% 5% 7% 4% 10% [libx264 @ 0xab87320] i4 v,h,dc,ddl,ddr,vr,hd,vl,hu: 32% 35% 12% 2% 4% 3% 4% 3% 5% [libx264 @ 0xab87320] Weighted P-Frames: Y:0.0% UV:0.0% [libx264 @ 0xab87320] ref P L0: 57.0% 5.6% 26.8% 10.6% [libx264 @ 0xab87320] ref B L0: 69.4% 22.6% 8.0% [libx264 @ 0xab87320] ref B L1: 93.7% 6.3% [libx264 @ 0xab87320] kb/s:2460.40

  Read the article

• Server HTTP Load times slow?

  - by cdog5000

  Hello, My server @ codemeh.com (HTTP Server) seems to be randomly loading slowly, I cannot tell if it just my forums (http://www.codemeh.com/forums/) that are loading slowly or if the WHOLE site is just loading slowly since my forums are the largest thing on the site right now. load average: 0.02, 0.17, 0.20 That is super low to my knowledge. I have tried Google Page Analytic plug-in for FireFox to solve the problem but nothing comes up that is VERY bad. If someone could investigate this for me since I am very new at apache and server configurations. Thanks! (top): PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 7493 www-data 15 0 98.2m 16m 9092 S 3 0.8 0:27.24 apache2 26429 www-data 15 0 98.2m 15m 7392 S 3 0.7 0:03.45 apache2 26477 www-data 17 0 98.2m 15m 7396 S 3 0.7 0:03.16 apache2 1 root 15 0 2468 1384 1156 S 0 0.1 0:00.49 init 1367 root 25 0 2564 816 660 S 0 0.0 0:00.00 xinetd 1526 root 15 0 29576 5420 1976 S 0 0.3 1:02.69 fail2ban-server 3703 root 15 0 13512 9312 1696 S 0 0.4 0:11.59 miniserv.pl 3915 postfix 15 0 6056 1652 1320 S 0 0.1 0:00.00 pickup 4010 root 15 0 4548 1296 972 S 0 0.1 0:37.36 ntpd 7448 root 15 0 98528 26m 20m S 0 1.3 0:00.27 apache2 7454 www-data 18 0 33580 2616 368 S 0 0.1 0:00.04 apache2 7528 www-data 18 0 108m 24m 15m S 0 1.2 0:27.60 apache2 7974 root 16 0 8700 2728 2164 S 0 0.1 0:00.08 sshd 8123 cdog5000 15 0 8832 1596 896 S 0 0.1 0:00.00 sshd 8126 cdog5000 18 0 4484 1716 1384 S 0 0.1 0:00.00 bash 8141 cdog5000 15 0 2344 980 796 R 0 0.0 0:00.11 top 13461 root 15 0 8700 2728 2164 S 0 0.1 0:00.07 sshd 13567 cdog5000 18 0 8832 1492 896 S 0 0.1 0:00.33 sshd 13569 cdog5000 18 0 4484 1728 1388 S 0 0.1 0:00.09 bash 17983 root 15 0 4392 1268 988 S 0 0.1 0:00.00 su 17987 root 15 0 4516 1752 1380 S 0 0.1 0:00.09 bash 18081 www-data 15 0 98.2m 14m 6588 S 0 0.7 0:04.91 apache2 20000 www-data 15 0 98.3m 15m 8040 S 0 0.8 0:02.45 apache2 20019 www-data 15 0 98.2m 14m 6808 S 0 0.7 0:04.97 apache2 30343 root 15 0 3964 1012 764 S 0 0.0 0:00.03 vsftpd 30382 root 15 0 2304 908 716 S 0 0.0 0:00.62 cron 30401 mysql 17 0 141m 17m 5416 S 0 0.9 1:02.20 mysqld 30424 root 15 0 5472 912 504 S 0 0.0 0:00.04 sshd 30473 syslog 15 0 1916 676 536 S 0 0.0 0:01.02 syslogd 30611 amavis 15 0 33872 25m 2292 S 0 1.2 0:03.11 amavisd-new 31890 amavis 18 0 34888 24m 1792 S 0 1.2 0:00.00 amavisd-new 31891 amavis 18 0 34888 24m 1784 S 0 1.2 0:00.00 amavisd-new 32397 clamav 18 0 104m 84m 1272 S 0 4.1 1:06.46 clamd 32563 clamav 15 0 12832 5716 4440 S 0 0.3 0:01.29 freshclam 32573 root 23 0 1892 456 372 S 0 0.0 0:00.00 courierlogger 32575 root 18 0 2096 684 544 S 0 0.0 0:00.01 authdaemond 32583 root 23 0 1892 360 284 S 0 0.0 0:00.00 courierlogger 32584 root 24 0 2000 612 516 S 0 0.0 0:00.00 couriertcpd 32598 root 23 0 1892 360 284 S 0 0.0 0:00.00 courierlogger 32599 root 25 0 2000 612 516 S 0 0.0 0:00.00 couriertcpd 32604 root 18 0 1892 460 372 S 0 0.0 0:00.00 courierlogger 32605 root 18 0 2000 624 532 S 0 0.0 0:00.00 couriertcpd 32607 root 18 0 2308 404 256 S 0 0.0 0:00.02 authdaemond 32608 root 18 0 2096 260 116 S 0 0.0 0:00.03 authdaemond 32609 root 15 0 2308 404 256 S 0 0.0 0:00.03 authdaemond 32610 root 18 0 2096 260 116 S 0 0.0 0:00.02 authdaemond 32612 root 18 0 2308 404 256 S 0 0.0 0:00.02 authdaemond 32621 root 24 0 1892 364 284 S 0 0.0 0:00.00 courierlogger 32622 root 25 0 2000 608 516 S 0 0.0 0:00.00 couriertcpd 32633 root 15 0 105m 936 716 S 0 0.0 0:02.26 nscd 32719 root 16 0 6252 1680 1344 S 0 0.1 0:01.24 master 32738 postfix 15 0 6188 1776 1400 S 0 0.1 0:00.44 qmgr 32758 postfix 15 0 6492 2564 1788 S 0 0.1 0:00.14 tlsmgr (/etc/apache2/sites-available/default): NameVirtualHost * <VirtualHost *> ServerAdmin webmaster@localhost DocumentRoot /var/www/web1/web/ <Directory /var/www/web1/web/> Options Indexes MultiViews AllowOverride None Order allow,deny allow from all </Directory> </VirtualHost> I have fail2ban server and I dont have any firewall at this point and time that I know of. SMF is 2.0 RC4 and apache version is 2.2.14. I run a MySQL server on another box in the same DC (Persistent Connection). I installed eAccelerator today and it didnt help.

  Read the article

• Sporadic unspecific kernel panic

  - by koma

  I'm experiencing seldom (so far about once a month) hard crashes on our ubuntu server 10.04 LTS box. The box itself is quite old (Dell PowerEdge 750 from 2004, Pentium4 2.8 GHz). I set up netconsole after it crashed twice last thursday and was able to extract the following output: [ 9354.062473] invalid opcode: 0000 [#1] SMP [ 9354.062516] last sysfs file: /sys/devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.0/uevent [ 9354.062555] Modules linked in: ppdev adm1026 hwmon_vid i2c_i801 bridge stp dcdbas psmouse serio_raw netconsole configfs shpchp lp parport usbhid hid e1000 [ 9354.062685] [ 9354.062704] Pid: 3988, comm: rsync Not tainted 2.6.38-12-generic-pae #51~lucid1-Ubuntu Dell Computer Corporation PowerEdge 750 /0R1479 [ 9354.062773] EIP: 0060:[<c104fef1>] EFLAGS: 00010046 CPU: 1 [ 9354.062802] EIP is at check_preempt_wakeup+0x181/0x250 [ 9354.062826] EAX: 00000002 EBX: f2a10ccc ECX: 00000000 EDX: 00000002 [ 9354.062850] ESI: f1db71cc EDI: f1db71a0 EBP: f1dbdea8 ESP: f1dbde8c [ 9354.062875] DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068 [ 9354.062900] Process rsync (pid: 3988, ti=f1dbc000 task=f1db71a0 task.ti=f1dbc000) [ 9354.062933] Stack: [ 9354.062951] 0053ea60 f7907680 f28da840 f2a10ca0 c153ea60 f7907680 c153ea60 f1dbdebc [ 9354.063019] c103f98a f2a10ca0 f7907680 00000001 f1dbdef8 c104f97f 00000000 f2f0bacc [ 9354.063088] f7904338 00000001 00000003 00000000 f2f0bacc 00000001 00000001 00000086 [ 9354.063157] Call Trace: [ 9354.063183] [<c103f98a>] check_preempt_curr+0x6a/0x80 [ 9354.063210] [<c104f97f>] try_to_wake_up+0x5f/0x3f0 [ 9354.063236] [<c1077a00>] ? hrtimer_wakeup+0x0/0x30 [ 9354.063261] [<c104fd64>] wake_up_process+0x14/0x20 [ 9354.063286] [<c1077a1d>] hrtimer_wakeup+0x1d/0x30 [ 9354.063310] [<c1077f4a>] __run_hrtimer+0x7a/0x1c0 [ 9354.063336] [<c107dbad>] ? ktime_get+0x6d/0x110 [ 9354.063360] [<c1078310>] hrtimer_interrupt+0x120/0x2b0 [ 9354.063390] [<c1535c36>] smp_apic_timer_interrupt+0x56/0x8a [ 9354.063418] [<c152f459>] apic_timer_interrupt+0x31/0x38 [ 9354.063446] [<c1520000>] ? mca_attach_bus+0x5/0xc0 [ 9354.063469] Code: 8b 9b 20 01 00 00 8b 86 24 01 00 00 3b 83 24 01 00 00 75 e6 85 db 0f 84 a3 00 00 00 89 da 89 f0 e8 75 f6 fe ff 83 f8 01 0f 85 00 <fe> ff ff 89 f8 e8 95 f9 fe ff 8b 5e 1c 85 db 0f 84 e4 fe ff ff [ 9354.063804] EIP: [<c104fef1>] check_preempt_wakeup+0x181/0x250 SS:ESP 0068:f1dbde8c [ 9354.064231] ---[ end trace 290689cea65aea7f ]--- [ 9354.064290] Kernel panic - not syncing: Fatal exception in interrupt [ 9354.064352] Pid: 3988, comm: rsync Tainted: G D 2.6.38-12-generic-pae #51~lucid1-Ubuntu [ 9354.064424] Call Trace: [ 9354.064481] [<c152c057>] ? panic+0x5c/0x15b [ 9354.064539] [<c15302bd>] ? oops_end+0xcd/0xd0 [ 9354.064539] [<c100d9e4>] ? die+0x54/0x80 [ 9354.064539] [<c152f926>] ? do_trap+0x96/0xc0 [ 9354.064539] [<c100ba00>] ? do_invalid_op+0x0/0xa0 [ 9354.064539] [<c100ba8b>] ? do_invalid_op+0x8b/0xa0 [ 9354.064539] [<c104fef1>] ? check_preempt_wakeup+0x181/0x250 [ 9354.064539] [<c144884d>] ? __kfree_skb+0x3d/0x90 [ 9354.064539] [<c1042ae7>] ? update_curr+0x247/0x2a0 [ 9354.064539] [<c10447bb>] ? update_cfs_load+0x11b/0x2d0 [ 9354.064539] [<c1042a25>] ? update_curr+0x185/0x2a0 [ 9354.064539] [<c152f6bf>] ? error_code+0x67/0x6c [ 9354.064539] [<c104fef1>] ? check_preempt_wakeup+0x181/0x250 [ 9354.064539] [<c103f98a>] ? check_preempt_curr+0x6a/0x80 [ 9354.064539] [<c104f97f>] ? try_to_wake_up+0x5f/0x3f0 [ 9354.064539] [<c1077a00>] ? hrtimer_wakeup+0x0/0x30 [ 9354.064539] [<c104fd64>] ? wake_up_process+0x14/0x20 [ 9354.064539] [<c1077a1d>] ? hrtimer_wakeup+0x1d/0x30 [ 9354.064539] [<c1077f4a>] ? __run_hrtimer+0x7a/0x1c0 [ 9354.064539] [<c107dbad>] ? ktime_get+0x6d/0x110 [ 9354.064539] [<c1078310>] ? hrtimer_interrupt+0x120/0x2b0 [ 9354.064539] [<c1535c36>] ? smp_apic_timer_interrupt+0x56/0x8a [ 9354.064539] [<c152f459>] ? apic_timer_interrupt+0x31/0x38 [ 9354.064539] [<c1520000>] ? mca_attach_bus+0x5/0xc0 Googling for this issue didn't really turn up anything useful (most stuff I found was related to btrfs, but I don't use that, although the module exists and is sometimes loaded). From experience it might have to do with relatively heavy I/O, as two of the panics happened during a backup procedure. Kernel is 2.6.38-12-generic-pae, but I'm pretty sure I also saw panics on 2.6.32. I meanwhile upgraded to 3.0.0-17-generic-pae and am waiting for the next crash ;-) I'm at a loss here, so any pointers where to look for the cause or what it could be would be great :-) Thanks !

  Read the article

• LXC Container Networking

  - by digitaladdictions

  I just started to experiment with LXC containers. I was able to create a container and start it up but I cannot get dhcp to assign the container an IP address. If I assign a static address the container can ping the host IP but not outside the host IP. The host is CentOS 6.5 and the guest is Ubuntu 14.04LTS. I used the template downloaded by lxc-create -t download -n cn-01 command. If I am trying to get an IP address on the same subnet as the host I don't believe I should need the IP tables rule for masquerading but I added it anyways. Same with IP forwarding. I compiled LXC by hand from the following source https://linuxcontainers.org/downloads/lxc-1.0.4.tar.gz Host Operating System Version #> cat /etc/redhat-release CentOS release 6.5 (Final) #> uname -a Linux localhost.localdomain 2.6.32-431.20.3.el6.x86_64 #1 SMP Thu Jun 19 21:14:45 UTC 2014 x86_64 x86_64 x86_64 GNU/Linux Container Config #> cat /usr/local/var/lib/lxc/cn-01/config # Template used to create this container: /usr/local/share/lxc/templates/lxc-download # Parameters passed to the template: # For additional config options, please look at lxc.container.conf(5) # Distribution configuration lxc.include = /usr/local/share/lxc/config/ubuntu.common.conf lxc.arch = x86_64 # Container specific configuration lxc.rootfs = /usr/local/var/lib/lxc/cn-01/rootfs lxc.utsname = cn-01 # Network configuration lxc.network.type = veth lxc.network.flags = up lxc.network.link = br0 LXC default.confu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:0c:29:12:30:f2 brd ff:ff:ff:ff:f #> cat /usr/local/etc/lxc/default.conf lxc.network.type = veth lxc.network.link = br0 lxc.network.flags = up #> lxc-checkconfig Kernel configuration not found at /proc/config.gz; searching... Kernel configuration found at /boot/config-2.6.32-431.20.3.el6.x86_64 --- Namespaces --- Namespaces: enabled Utsname namespace: enabled Ipc namespace: enabled Pid namespace: enabled User namespace: enabled Network namespace: enabled Multiple /dev/pts instances: enabled --- Control groups --- Cgroup: enabled Cgroup namespace: enabled Cgroup device: enabled Cgroup sched: enabled Cgroup cpu account: enabled Cgroup memory controller: /usr/local/bin/lxc-checkconfig: line 103: [: too many arguments enabled Cgroup cpuset: enabled --- Misc --- Veth pair device: enabled Macvlan: enabled Vlan: enabled File capabilities: /usr/local/bin/lxc-checkconfig: line 118: [: -gt: unary operator expected Note : Before booting a new kernel, you can check its configuration usage : CONFIG=/path/to/config /usr/local/bin/lxc-checkconfig Network Config (HOST) #> cat /etc/sysconfig/network-scripts/ifcfg-br0 DEVICE=br0 TYPE=Bridge BOOTPROTO=dhcp ONBOOT=yes #> cat /etc/sysconfig/network-scripts/ifcfg-eth0 DEVICE=eth0 ONBOOT=yes TYPE=Ethernet IPV6INIT=no USERCTL=no BRIDGE=br0 #> cat /etc/networks default 0.0.0.0 loopback 127.0.0.0 link-local 169.254.0.0 #> ip a s 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:0c:29:12:30:f2 brd ff:ff:ff:ff:ff:ff inet6 fe80::20c:29ff:fe12:30f2/64 scope link valid_lft forever preferred_lft forever 3: pan0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN link/ether 42:7e:43:b3:61:c5 brd ff:ff:ff:ff:ff:ff 4: br0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN link/ether 00:0c:29:12:30:f2 brd ff:ff:ff:ff:ff:ff inet 10.60.70.121/24 brd 10.60.70.255 scope global br0 inet6 fe80::20c:29ff:fe12:30f2/64 scope link valid_lft forever preferred_lft forever 12: vethT6BGL2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether fe:a1:69:af:50:17 brd ff:ff:ff:ff:ff:ff inet6 fe80::fca1:69ff:feaf:5017/64 scope link valid_lft forever preferred_lft forever #> brctl show bridge name bridge id STP enabled interfaces br0 8000.000c291230f2 no eth0 vethT6BGL2 pan0 8000.000000000000 no #> cat /proc/sys/net/ipv4/ip_forward 1 # Generated by iptables-save v1.4.7 on Fri Jul 11 15:11:36 2014 *nat :PREROUTING ACCEPT [34:6287] :POSTROUTING ACCEPT [0:0] :OUTPUT ACCEPT [0:0] -A POSTROUTING -o eth0 -j MASQUERADE COMMIT # Completed on Fri Jul 11 15:11:36 2014 Network Config (Container) #> cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback auto eth0 iface eth0 inet dhcp #> ip a s 11: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 02:69:fb:42:ee:d7 brd ff:ff:ff:ff:ff:ff inet6 fe80::69:fbff:fe42:eed7/64 scope link valid_lft forever preferred_lft forever 13: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever

  Read the article

• Linux/Apache performance very slow even on local network

  - by klausch

  I have an Ubuntu server machine running Apache and MYSQL. System and version info is as follows: Linux kernel 3.0.0.-12 Apache/2.2.20 MySQL Ver 14.14.Distrib 5.1.58 I am running a few websites on this server, some HTML only, some PHP/MySQL. THe [problem is that response time is very slow, both on static as well as the dynamic sites. Sometimes it takes more than 10 seconds before a response is given, this makes the sites very slow and almost unusable. The problem occurs even when requesting from the local network. I have added the involved subdomains to my /etc/hosts file, and abolve all the problem is not solved by using IP numbers instead of URL's. So there is no DNS lookup issue. I have modified the log format by showing the response times and sometimes a files takes 12 seconds to be served, see the jquery~.js file in the example screenshot. I have no explanation for this extremely long response time, but is is not even the only issue here, some other files takes a long time to be served too, but do not show a long response time in the log file. So probably different tissues are involved here. I cannot find a solution until now, any suggestions??? THanx in advance, Klaas link to screenshot picture from access logfile Some extra configuration info: apache2.conf (comment is removed) LockFile ${APACHE_LOCK_DIR}/accept.lock PidFile ${APACHE_PID_FILE} Timeout 300 KeepAlive On MaxKeepAliveRequests 100 KeepAliveTimeout 5 <IfModule mpm_prefork_module> StartServers 5 MinSpareServers 5 MaxSpareServers 10 MaxClients 150 MaxRequestsPerChild 0 </IfModule> <IfModule mpm_worker_module> StartServers 2 MinSpareThreads 25 MaxSpareThreads 75 ThreadLimit 64 ThreadsPerChild 25 MaxClients 150 MaxRequestsPerChild 0 </IfModule> <IfModule mpm_event_module> StartServers 2 MinSpareThreads 25 MaxSpareThreads 75 ThreadLimit 64 ThreadsPerChild 25 MaxClients 150 MaxRequestsPerChild 0 </IfModule> User ${APACHE_RUN_USER} Group ${APACHE_RUN_GROUP} AccessFileName .htaccess <Files ~ "^\.ht"> Order allow,deny Deny from all Satisfy all </Files> DefaultType text/plain HostnameLookups Off ErrorLog ${APACHE_LOG_DIR}/error.log LogLevel warn Include mods-enabled/*.load Include mods-enabled/*.conf Include httpd.conf Include ports.conf LogFormat "%v:%p %h %l %u %t \"%r\" %>s %O \"%{Referer}i\" \"%{User-Agent}i\"" vhost_combined LogFormat "%h %l %u %t \"%r\" %>s %O \"%{Referer}i\" \"%{User-Agent}i\" %T/%D" combined LogFormat "%h %l %u %t \"%r\" %>s %O" common LogFormat "%{Referer}i -> %U" referer LogFormat "%{User-agent}i" agent Include conf.d/ Include sites-enabled/ And the virtual hostfile for one of the slow sites, in fact it is pretty straightforward... <VirtualHost *:80> ServerAdmin [email protected] ServerSignature EMail ServerName toenjoy.drsklaus.nl DocumentRoot /var/www/toenjoy.drsklaus.nl <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/toenjoy.drsklaus.nl/> Options Indexes FollowSymLinks MultiViews AllowOverride AuthConfig AuthType Basic AuthName "To Enjoy" AuthUserFile /etc/.htpasswd Require user petraaa Order allow,deny allow from all </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog /var/log/apache2/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> </VirtualHost> And the output of free -m: klaas@ubuntu-server:/etc/apache2$ free -m total used free shared buffers cached Mem: 1997 1401 595 0 144 1017 -/+ buffers/cache: 238 1758 Swap: 2035 0 2035 and I have no indication that swapping occurs on the moments the site is slow. I have runned top and it does not appear to be a CPU issue. I have the impression that the spawning of a apache thread could maybe be the bottleneck but it is just a suggestion. Maybe this gives some extra information! EDIT: The problem seemed to be gone for some time but occurs again! And not only with Apache, also connecting using SSH takes a tremendous time, sometimes it takes up to 15 seconds before the keyphrase is asked for. Also scp works very slowly. The behavious is really unpredoctable and makes the server very hard to use. Any ideas...?

  Read the article

• C# performance varying due to memory

  - by user1107474

  Hope this is a valid post here, its a combination of C# issues and hardware. I am benchmarking our server because we have found problems with the performance of our quant library (written in C#). I have simulated the same performance issues with some simple C# code- performing very heavy memory-usage. The code below is in a function which is spawned from a threadpool, up to a maximum of 32 threads (because our server has 4x CPUs x 8 cores each). This is all on .Net 3.5 The problem is that we are getting wildly differing performance. I run the below function 1000 times. The average time taken for the code to run could be, say, 3.5s, but the fastest will only be 1.2s and the slowest will be 7s- for the exact same function! I have graphed the memory usage against the timings and there doesnt appear to be any correlation with the GC kicking in. One thing I did notice is that when running in a single thread the timings are identical and there is no wild deviation. I have also tested CPU-bound algorithms and the timings are identical too. This has made us wonder if the memory bus just cannot cope. I was wondering could this be another .net or C# problem, or is it something related to our hardware? Would this be the same experience if I had used C++, or Java?? We are using 4x Intel x7550 with 32GB ram. Is there any way around this problem in general? Stopwatch watch = new Stopwatch(); watch.Start(); List<byte> list1 = new List<byte>(); List<byte> list2 = new List<byte>(); List<byte> list3 = new List<byte>(); int Size1 = 10000000; int Size2 = 2 * Size1; int Size3 = Size1; for (int i = 0; i < Size1; i++) { list1.Add(57); } for (int i = 0; i < Size2; i = i + 2) { list2.Add(56); } for (int i = 0; i < Size3; i++) { byte temp = list1.ElementAt(i); byte temp2 = list2.ElementAt(i); list3.Add(temp); list2[i] = temp; list1[i] = temp2; } watch.Stop(); (the code is just meant to stress out the memory) I would include the threadpool code, but we used a non-standard threadpool library. EDIT: I have reduced "size1" to 100000, which basically doesn't use much memory and I still get a lot of jitter. This suggests it's not the amount of memory being transferred, but the frequency of memory grabs?

  Read the article

• How to make MySQL utilize available system resources, or find "the real problem"?

  - by anonymous coward

  This is a MySQL 5.0.26 server, running on SuSE Enterprise 10. This may be a Serverfault question. The web user interface that uses these particular queries (below) is showing sometimes 30+, even up to 120+ seconds at the worst, to generate the pages involved. On development, when the queries are run alone, they take up to 20 seconds on the first run (with no query cache enabled) but anywhere from 2 to 7 seconds after that - I assume because the tables and indexes involved have been placed into ram. From what I can tell, the longest load times are caused by Read/Update Locking. These are MyISAM tables. So it looks like a long update comes in, followed by a couple 7 second queries, and they're just adding up. And I'm fine with that explanation. What I'm not fine with is that MySQL doesn't appear to be utilizing the hardware it's on, and while the bottleneck seems to be the database, I can't understand why. I would say "throw more hardware at it", but we did and it doesn't appear to have changed the situation. Viewing a 'top' during the slowest times never shows much cpu or memory utilization by mysqld, as if the server is having no trouble at all - but then, why are the queries taking so long? How can I make MySQL use the crap out of this hardware, or find out what I'm doing wrong? Extra Details: On the "Memory Health" tab in the MySQL Administrator (for Windows), the Key Buffer is less than 1/8th used - so all the indexes should be in RAM. I can provide a screen shot of any graphs that might help. So desperate to fix this issue. Suffice it to say, there is legacy code "generating" these queries, and they're pretty much stuck the way they are. I have tried every combination of Indexes on the tables involved, but any suggestions are welcome. Here's the current Create Table statement from development (the 'experimental' key I have added, seems to help a little, for the example query only): CREATE TABLE `registration_task` ( `id` varchar(36) NOT NULL default '', `date_entered` datetime NOT NULL default '0000-00-00 00:00:00', `date_modified` datetime NOT NULL default '0000-00-00 00:00:00', `assigned_user_id` varchar(36) default NULL, `modified_user_id` varchar(36) default NULL, `created_by` varchar(36) default NULL, `name` varchar(80) NOT NULL default '', `status` varchar(255) default NULL, `date_due` date default NULL, `time_due` time default NULL, `date_start` date default NULL, `time_start` time default NULL, `parent_id` varchar(36) NOT NULL default '', `priority` varchar(255) NOT NULL default '9', `description` text, `order_number` int(11) default '1', `task_number` int(11) default NULL, `depends_on_id` varchar(36) default NULL, `milestone_flag` varchar(255) default NULL, `estimated_effort` int(11) default NULL, `actual_effort` int(11) default NULL, `utilization` int(11) default '100', `percent_complete` int(11) default '0', `deleted` tinyint(1) NOT NULL default '0', `wf_task_id` varchar(36) default '0', `reg_field` varchar(8) default '', `date_offset` int(11) default '0', `date_source` varchar(10) default '', `date_completed` date default '0000-00-00', `completed_id` varchar(36) default NULL, `original_name` varchar(80) default NULL, PRIMARY KEY (`id`), KEY `idx_reg_task_p` (`deleted`,`parent_id`), KEY `By_Assignee` (`assigned_user_id`,`deleted`), KEY `status_assignee` (`status`,`deleted`), KEY `experimental` (`deleted`,`status`,`assigned_user_id`,`parent_id`,`date_due`) ) ENGINE=MyISAM DEFAULT CHARSET=latin1 And one of the ridiculous queries in question: SELECT users.user_name assigned_user_name, registration.FIELD001 parent_name, registration_task.status status, registration_task.date_modified date_modified, registration_task.date_due date_due, registration.FIELD240 assigned_wf, if(LENGTH(registration_task.description)>0,1,0) has_description, registration_task.* FROM registration_task LEFT JOIN users ON registration_task.assigned_user_id=users.id LEFT JOIN registration ON registration_task.parent_id=registration.id where (registration_task.status != 'Completed' AND registration.FIELD001 LIKE '%' AND registration_task.name LIKE '%' AND registration.FIELD060 LIKE 'GN001472%') AND registration_task.deleted=0 ORDER BY date_due asc LIMIT 0,20; my.cnf - '[mysqld]' section. [mysqld] port = 3306 socket = /var/lib/mysql/mysql.sock skip-locking key_buffer = 384M max_allowed_packet = 100M table_cache = 2048 sort_buffer_size = 2M net_buffer_length = 100M read_buffer_size = 2M read_rnd_buffer_size = 160M myisam_sort_buffer_size = 128M query_cache_size = 16M query_cache_limit = 1M EXPLAIN above query, without additional index: +----+-------------+-------------------+--------+--------------------------------+----------------+---------+------------------------------------------------+---------+-----------------------------+ | id | select_type | table | type | possible_keys | key | key_len | ref | rows | Extra | +----+-------------+-------------------+--------+--------------------------------+----------------+---------+------------------------------------------------+---------+-----------------------------+ | 1 | SIMPLE | registration_task | ref | idx_reg_task_p,status_assignee | idx_reg_task_p | 1 | const | 1067354 | Using where; Using filesort | | 1 | SIMPLE | registration | eq_ref | PRIMARY,gbl | PRIMARY | 8 | sugarcrm401.registration_task.parent_id | 1 | Using where | | 1 | SIMPLE | users | ref | PRIMARY | PRIMARY | 38 | sugarcrm401.registration_task.assigned_user_id | 1 | | +----+-------------+-------------------+--------+--------------------------------+----------------+---------+------------------------------------------------+---------+-----------------------------+ EXPLAIN above query, with 'experimental' index: +----+-------------+-------------------+--------+-----------------------------------------------------------+------------------+---------+------------------------------------------------+--------+-----------------------------+ | id | select_type | table | type | possible_keys | key | key_len | ref | rows | Extra | +----+-------------+-------------------+--------+-----------------------------------------------------------+------------------+---------+------------------------------------------------+--------+-----------------------------+ | 1 | SIMPLE | registration_task | range | idx_reg_task_p,status_assignee,NewIndex1,tcg_experimental | tcg_experimental | 259 | NULL | 103345 | Using where; Using filesort | | 1 | SIMPLE | registration | eq_ref | PRIMARY,gbl | PRIMARY | 8 | sugarcrm401.registration_task.parent_id | 1 | Using where | | 1 | SIMPLE | users | ref | PRIMARY | PRIMARY | 38 | sugarcrm401.registration_task.assigned_user_id | 1 | | +----+-------------+-------------------+--------+-----------------------------------------------------------+------------------+---------+------------------------------------------------+--------+-----------------------------+

  Read the article

• What language/framework (technology) to use for website (flash games portal)

  - by cripox

  Hello, I know there are a lot of similar questions on the net, but because I am a newbie in web development I didn't find the solution for my specific problem. I am planing on creating a flash games portal from scratch. It is a big chance that there will be big traffic from the beginning (millions of pageviews). I want to reduce the server costs as much as possible but in the same time to not be tide to an expensive contract as there is a chance that the project will not be as successfully as I want and in that case the money would be very little. The question is : what technology to use? I don't know any web dev technology yet so it doesn't matter what I will learn. My web dev experience is a little php 8 years ago, and from then I programmed in C++ / Java- game and mobile development. I like Java and C syntax and language very much and I tend to dislike dynamic typing or non robust scripting (like php)- but I can get along if these are the best choices. The candidates are now: - Grails (my best for now) Ruby on Rails Cake PHP Other technologies (Google App Engine, Python/Django etc...) I was considering at first using pure C and compiling the web app in the server- just to squeeze more from the servers, but soon I understand that this is overkill. Next my eyes came on Ruby - as there is a lot of buzz for it's easiness of use. Next I discovered Grails and looked at Java because it is said that it is "faster". But I don't know what this "Faster" really means on my needs, so here comes the first question: 1) What will be my biggest consumption on the server, other than bandwidth, for a lot of flash content requests? Is it memory? I heard that Java needs a lot of memory, but is faster. Is it CPU? I am planning to take some daily VPS.NET nodes at first, to see if there is a demand, and if the "spike" is permanent to move to a dedicated server (serverloft.com has some good offers), else to remain with less nodes. I was also considering developing in Google App Engine- cheap or free hosting to use at first - so I can test my assumption- and also very easy to use (no need for sys administration) but the costs became high if used more ( 3 million games played / month .. x mb/ each). And the issue with Google is that it looks me in this technology. My other concern is scalability (not only for traffic/users, but as adding functionality) My plans are to release a functional site in just 4 weeks (just the basics frontend and some quick basic backend - so I can be able to modify some things and add games manually) - but then to raise it and add more things to it. I am planning to take a little different approach than other portals so I need to write it from scratch (a script will not do). 2) Will Grails take much more resources than RoR or Php server wise? I heard that making it on Java stack will be hardware expensive and is overkill if you don't make a bank application. My application will not be very complex (I hope and i will try to) but will have a lot of traffic. I also took in account using CDN for files, but the cheapest CDN found was 5c/GB (vps.net) and the cost per gb on serverloft (http://www.serverloft.com/dedizierte-server/server-details.php?products=4) is only 1.79 cents/GB and comes with the other resources either. I am new to this domain (web). I am learning the ropes and searching on the web for ~half of year but don't have any really practical experience, so I know that I must have some naive thinking and other issues that i don't know from now, so please give me any advice you want regarding anything, not just the specific questions asked. And thank you so much for such great community!

  Read the article

• CodePlex Daily Summary for Thursday, February 25, 2010

  CodePlex Daily Summary for Thursday, February 25, 2010New ProjectsAptusSoftware.Threading: AptusSoftware.Threading is a class library designed primarily to assist in the development of multi-threaded WinForm applications, although there i...AxiomGameDesigner: It is going to be a universal scene editor for Axiom 3D game engine. It is in pure C# and will be kept portable to MONO for compatibility with linu...Badger - Unity Productivity Extensions: A set of Microsoft Unity Extensions. Why Badger? Because I love badgers.Business & System Analysis Templates and Best Practices for Russian: http://saway.codeplex.com/Conectayas: Conectayas is an open source "Connect Four" alike game but transformable to "Tic-Tac-Toe" and to a lot of similar games that uses mouse. Written in...FastCode: .NET 3.5 Extensions set to increase coding speed.Hundiyas: Hundiyas is an open source "Battleship" alike game totally written in DHTML (JavaScript, CSS and HTML) that uses mouse. This cross-platform and cro...Icelandic Online Banking: Icelandic Online Banking is project defining a web service interface for online banking.IE8 AddOns XML Creator: Application that helps on creating the xml files for IE8 Accelerators, Search Providers and the markup for Web Slices.iKnowledge: a asp.net mvc demoLearn ASP.NET MVC: Learn ASP.NET MVC is a project for the members of the Peer Learning group in Silicon Valley. It contains the SportsStore solution from the Pro ASP...Live at Education Meta Web-Service: Live at Education Meta Web-Service is intended to abstract from several technologies that are included in Live@edu set of services. This web-ser...Low level wave sound output for VB.NET: Low level sound output class for VB.NET using platform invocation services to call winmm.dllMailQ: MailQ makes it easier for developers to send mail messages from an application. The system sends mails based on a database queue system (store, se...Managed DXGI: Managed DXGI library is Fully managed wrapper writen on C# for DXGI 1.0 and 1.1 technology. It makes easier to support DXGI in managed application....Multivalue AutoComplete WinForms TextBox in C#: This project is a sample application that demonstrates how to create a multivalue WinForms textbox in C# using .NET Framework 3.5.Nifty CSharp Tools: Nifty CSharp Tools, will contain various tools and snippets. IRCBot, splashscreens, linq, world of warcraft log parsing, screenshot uploaders, twi...PHP MPQ: A port of StormLib to PHP for handling Blizzard MPQ files.RedDevils strategy - Project Hoshimi Programming Battle: Source Code of RedDevils strategy. Imagine Cup 2008 - Project Hoshimi Programming Battle.RNUNIT: rNunit is a distributed Nunit project. Many application these days are client-server application, distributed application and regular unit testing ...Samar Solution: Samar Solutions is a business system for office automation.Silverlight OOMRPG Game Engine: Silverlight OOMRPG Game EngineSimulator: GPSSimulatorSLARToolkit - Silverlight Augmented Reality Toolkit: SLARToolkit is a flexible Augmented Reality library for Silverlight with the aim to make real time Augmented Reality applications with Silverlight ...Spiral Architecture Driven Development (SADD) for Russian: Это русская версия сайта sadd.codeplex.comSQLSnapshotManager: Easily manage SQL Server database snapshots in a easy to use visual interface.Twilio with VB.NET MVC: Twilio with VB.NET MVC is a sample application for developing with Twilio's REST based telephony API. It includes an XML Schema of the TwiML respon...Ultra Speed Dial: UltraSpeedDial.com - Online Speed Dial Page.Visual HTML Editor justHTML: justHTML - is simle windows-application WYSIWYG editor that allow everyone - without any knowledge of HTML - to create and edit web-pages. It supp...WinMTR.NET: .NET Clone of the popular Windows clone of the popular Linux Matt's TracerouteWPF Dialogs: "WPF Dialogs" is a library for different Dialogs in WPF (e.g. FolderBrowseDialog, SaveFileDialog, OpenFileDialog etc.). These Dialogs are written i...WPFLogin: A small Login window in WPF and C#XNA PerformanceTimers: CPU Timers for Windows and Xbox360. Can track multiple threads, and presents output as a log on-screen.New ReleasesAptusSoftware.Threading: 2.0.0: First public release. This release is in production as part of several commercial applications and is stable. The source code download includes a...BizTalk Software Factory: BizTalk Software Factory v2.1: This is a service release for the BizTalk Software Factory for BizTalk Server 2009, containing so far: Fix for x64: the SN.EXE tool is now locate...Business & System Analysis Templates and Best Practices for Russian: R00 The Place reserver: Just to reserve the place Will be filled out soonChronos WPF: Chronos v1.0 Beta 2: Added a new SplashScreen Added a new Login View and implemented Log Off Added a new PasswordBoxHelper (http://www.codeproject.com/Articles/371...dotNetTips: dotNetTips.Utility 3.5 R2: This is a new release (version 3.5.0.3) compatible with .NET 3.5. Lots of new classes/features!! Requires SP1 if using the Entity Framework extensi...fleXdoc: template-based server-side document generator (docx): fleXdoc 1.0 beta 3: The third and final beta of fleXdoc. fleXdoc consists of a webservice and a (test)client for the service. Make sure you also download the testclien...FluentPS: FluentPS v1.0: - FluentPS is moved from ASMX to WCF interface of the Project Server Interface (PSI) - Impersonation changes to work in compliance with WCF interfa...FolderSize: FolderSize.Win32.1.0.4.0: FolderSize.Win32.1.0.3.0 A simple utility intended to be used to scan harddrives for the folders that take most place and display this to the user...iTuner - The iTunes Companion: iTuner 1.1.3707 Beta 3: As promised, the iTuner Automated Librarian is now available. This automatically cleans an entire album of dead tracks and duplicates as tracks ar...Live at Education Meta Web-Service: LAEMWS v 1.0 beta: Release Candidate for LAEMWS.Macaw Reusable Code Library: LanguageConfigurationSolution: This Solution helps developing a multi language publishing web siteManaged DXGI: Initial Release.: Base declaration of interfaces, most of them untested yet.Math.NET Numerics: 2010.2.24.667 Build: Latest alpha buildMiniTwitter: 1.08.1: MiniTwitter 1.08.1 更新内容 変更 インクリメンタル検索時には大文字小文字の区別をしないように変更 クライアント名の表示を本家にあわせて from から via に変更 修正 公式 RT 時にステータスが上に表示されたり二重に表示されるバグを修正 自分が自分へ返信...Multivalue AutoComplete WinForms TextBox in C#: 1.0 First public release: Multivalue autocomplete textbox control and host application in this release are released in a single Visual Studio 2008 projects. See my related b...NMock3: NMock3 - Beta3, .NET 3.5: This release has some exciting new features. Please start providing feedback on the tutorials. The first several are complete and the rest are no...nxAjax - an asp.net ajax library using jQuery: nxAjax v3 codeplex 7: nxAjax v3 codeplex 7 binary and test website. Bug Fixed: ajax:Form control Add: Drag and drop Rewritten: DragnDropManager DragPanel DropPan...Office Apps: 0.8.7: whats new? Document.Editor and Document.Viewer now supports FlowDocument (.xaml) files bug fix'sPDF Rider: PDF Rider 0.3: Application PrerequisitesMicrosoft Windows Operating Systems (XP (tested) - Vista - 7) Microsoft .NET Framework 3.5 runtime A PDF rendering sof...ShellLight: ShellLight 0.1.0.1 Src: Codeplex project released. This is only a preview of the product. Until the first final release there will be many improvements.Silverlight OOMRPG Game Engine: SilverlightGameTutorialSolution v1.01: Please visit my blog for Silverlight OOMROG Game Tutorial: http://www.cnblogs.com/Jax/archive/2010/02/24/1673053.html.Simple Savant: Simple Savant v0.4: Added support for full-text indexing (See Full-Text Indexing) Added support for attribute spanning and compression for property values larger tha...Spiral Architecture Driven Development (SADD) for Russian: R00: R00 to reserve site nameTeamReview - TFS Code Review: Release 1.1.3: Release Features New expanded product positioning for capturing any targeted coding work as a trackable, assignable, reportable Work Item for any r...Text Designer Outline Text Library: 10th minor release: Version 0.3.1 (10th minor release)Fixed the gradient brush being too big for the text, resulting in not much gradient shown in the text. Gradient...TFS Workflow Control: TeamExplorer and TSWA control 1.0 for TFS 2010 RC: This is a special version for TFS 2010 RC. Use the RC version of the power tools to modify the layout of your work items (http://visualstudiogaller...thinktecture WSCF.blue: WSCF.blue V1 Update (1.0.7) - VS2010 RC Support: This update adds support for Visual Studio 2010 RC in addition to Visual Studio 2008. Please note that Visual Studio 2010 Beta 2 is NOT supported a...Tumblen3: tumblen3 Version 25Feb2010: ready for Twitter's xAuthUMD文本编辑器: UMDEditor文本编辑器V2.1.0: 2.1.0 (2010-02-24) 增加查找章节内指定文本内容的功能 2.0.4 (2010-02-06) 章节内容框增加右键菜单，包含编辑文本的基本操作 ------------------------------------------------------- 执行 reg.bat ...VCC: Latest build, v2.1.30224.0: Automatic drop of latest buildVisual HTML Editor justHTML: Latest binary: Latest buid here. Executable and mshtml.dll included in this archive. Ready to use ;)Visual HTML Editor justHTML: Source code for version 2.5: Visual studio 2008 project with full source code.VOB2MKV: vob2mkv-1.0.2: The release vob2mkv-1.0.2 is a feature update of the VOB2MKV project. It now includes a DirectShow source filter, MKVSOURCE. A source filter allo...WinMTR.NET: V 1.0: V 1.0WPF Dialogs: Version 0.1.0: Version 0.1.0 FolderBrowseDialog is implementet for more information look here Version 0.1.0 (german: Version 0.1.0 - Deutsch).WPF Dialogs: Version 0.1.1: Version 0.1.1 Features FolderBrowseDialog was extended / FolderBrowseDialog - Deutsch wurde erweitertXNA PerformanceTimers: XNA PerformanceTimers 0.1: Initial release.Zeta Resource Editor: Release 2010-02-24: Added HTTP proxy server support.Most Popular ProjectsASP.NET Ajax LibraryManaged Extensibility FrameworkWindows 7 USB/DVD Download ToolDotNetZip LibraryMDownloaderVirtual Router - Wifi Hot Spot for Windows 7 / 2008 R2MFCMAPIDroid ExplorerUseful Sharepoint Designer Custom Workflow ActivitiesOxiteMost Active ProjectsDinnerNow.netBlogEngine.NETRawrInfoServiceSLARToolkit - Silverlight Augmented Reality ToolkitNB_Store - Free DotNetNuke Ecommerce Catalog ModuleSharpMap - Geospatial Application Framework for the CLRjQuery Library for SharePoint Web ServicesRapid Entity Framework. (ORM). CTP 2Common Context Adapters

  Read the article

• SQL SERVER – Guest Post – Jonathan Kehayias – Wait Type – Day 16 of 28

  - by pinaldave

  Jonathan Kehayias (Blog | Twitter) is a MCITP Database Administrator and Developer, who got started in SQL Server in 2004 as a database developer and report writer in the natural gas industry. After spending two and a half years working in TSQL, in late 2006, he transitioned to the role of SQL Database Administrator. His primary passion is performance tuning, where he frequently rewrites queries for better performance and performs in depth analysis of index implementation and usage. Jonathan blogs regularly on SQLBlog, and was a coauthor of Professional SQL Server 2008 Internals and Troubleshooting. On a personal note, I think Jonathan is extremely positive person. In every conversation with him I have found that he is always eager to help and encourage. Every time he finds something needs to be approved, he has contacted me without hesitation and guided me to improve, change and learn. During all the time, he has not lost his focus to help larger community. I am honored that he has accepted to provide his views on complex subject of Wait Types and Queues. Currently I am reading his series on Extended Events. Here is the guest blog post by Jonathan: SQL Server troubleshooting is all about correlating related pieces of information together to indentify where exactly the root cause of a problem lies. In my daily work as a DBA, I generally get phone calls like, “So and so application is slow, what’s wrong with the SQL Server.” One of the funny things about the letters DBA is that they go so well with Default Blame Acceptor, and I really wish that I knew exactly who the first person was that pointed that out to me, because it really fits at times. A lot of times when I get this call, the problem isn’t related to SQL Server at all, but every now and then in my initial quick checks, something pops up that makes me start looking at things further. The SQL Server is slow, we see a number of tasks waiting on ASYNC_IO_COMPLETION, IO_COMPLETION, or PAGEIOLATCH_* waits in sys.dm_exec_requests and sys.dm_exec_waiting_tasks. These are also some of the highest wait types in sys.dm_os_wait_stats for the server, so it would appear that we have a disk I/O bottleneck on the machine. A quick check of sys.dm_io_virtual_file_stats() and tempdb shows a high write stall rate, while our user databases show high read stall rates on the data files. A quick check of some performance counters and Page Life Expectancy on the server is bouncing up and down in the 50-150 range, the Free Page counter consistently hits zero, and the Free List Stalls/sec counter keeps jumping over 10, but Buffer Cache Hit Ratio is 98-99%. Where exactly is the problem? In this case, which happens to be based on a real scenario I faced a few years back, the problem may not be a disk bottleneck at all; it may very well be a memory pressure issue on the server. A quick check of the system spec’s and it is a dual duo core server with 8GB RAM running SQL Server 2005 SP1 x64 on Windows Server 2003 R2 x64. Max Server memory is configured at 6GB and we think that this should be enough to handle the workload; or is it? This is a unique scenario because there are a couple of things happening inside of this system, and they all relate to what the root cause of the performance problem is on the system. If we were to query sys.dm_exec_query_stats for the TOP 10 queries, by max_physical_reads, max_logical_reads, and max_worker_time, we may be able to find some queries that were using excessive I/O and possibly CPU against the system in their worst single execution. We can also CROSS APPLY to sys.dm_exec_sql_text() and see the statement text, and also CROSS APPLY sys.dm_exec_query_plan() to get the execution plan stored in cache. Ok, quick check, the plans are pretty big, I see some large index seeks, that estimate 2.8GB of data movement between operators, but everything looks like it is optimized the best it can be. Nothing really stands out in the code, and the indexing looks correct, and I should have enough memory to handle this in cache, so it must be a disk I/O problem right? Not exactly! If we were to look at how much memory the plan cache is taking by querying sys.dm_os_memory_clerks for the CACHESTORE_SQLCP and CACHESTORE_OBJCP clerks we might be surprised at what we find. In SQL Server 2005 RTM and SP1, the plan cache was allowed to take up to 75% of the memory under 8GB. I’ll give you a second to go back and read that again. Yes, you read it correctly, it says 75% of the memory under 8GB, but you don’t have to take my word for it, you can validate this by reading Changes in Caching Behavior between SQL Server 2000, SQL Server 2005 RTM and SQL Server 2005 SP2. In this scenario the application uses an entirely adhoc workload against SQL Server and this leads to plan cache bloat, and up to 4.5GB of our 6GB of memory for SQL can be consumed by the plan cache in SQL Server 2005 SP1. This in turn reduces the size of the buffer cache to just 1.5GB, causing our 2.8GB of data movement in this expensive plan to cause complete flushing of the buffer cache, not just once initially, but then another time during the queries execution, resulting in excessive physical I/O from disk. Keep in mind that this is not the only query executing at the time this occurs. Remember the output of sys.dm_io_virtual_file_stats() showed high read stalls on the data files for our user databases versus higher write stalls for tempdb? The memory pressure is also forcing heavier use of tempdb to handle sorting and hashing in the environment as well. The real clue here is the Memory counters for the instance; Page Life Expectancy, Free List Pages, and Free List Stalls/sec. The fact that Page Life Expectancy is fluctuating between 50 and 150 constantly is a sign that the buffer cache is experiencing constant churn of data, once every minute to two and a half minutes. If you add to the Page Life Expectancy counter, the consistent bottoming out of Free List Pages along with Free List Stalls/sec consistently spiking over 10, and you have the perfect memory pressure scenario. All of sudden it may not be that our disk subsystem is the problem, but is instead an innocent bystander and victim. Side Note: The Page Life Expectancy counter dropping briefly and then returning to normal operating values intermittently is not necessarily a sign that the server is under memory pressure. The Books Online and a number of other references will tell you that this counter should remain on average above 300 which is the time in seconds a page will remain in cache before being flushed or aged out. This number, which equates to just five minutes, is incredibly low for modern systems and most published documents pre-date the predominance of 64 bit computing and easy availability to larger amounts of memory in SQL Servers. As food for thought, consider that my personal laptop has more memory in it than most SQL Servers did at the time those numbers were posted. I would argue that today, a system churning the buffer cache every five minutes is in need of some serious tuning or a hardware upgrade. Back to our problem and its investigation: There are two things really wrong with this server; first the plan cache is excessively consuming memory and bloated in size and we need to look at that and second we need to evaluate upgrading the memory to accommodate the workload being performed. In the case of the server I was working on there were a lot of single use plans found in sys.dm_exec_cached_plans (where usecounts=1). Single use plans waste space in the plan cache, especially when they are adhoc plans for statements that had concatenated filter criteria that is not likely to reoccur with any frequency.  SQL Server 2005 doesn’t natively have a way to evict a single plan from cache like SQL Server 2008 does, but MVP Kalen Delaney, showed a hack to evict a single plan by creating a plan guide for the statement and then dropping that plan guide in her blog post Geek City: Clearing a Single Plan from Cache. We could put that hack in place in a job to automate cleaning out all the single use plans periodically, minimizing the size of the plan cache, but a better solution would be to fix the application so that it uses proper parameterized calls to the database. You didn’t write the app, and you can’t change its design? Ok, well you could try to force parameterization to occur by creating and keeping plan guides in place, or we can try forcing parameterization at the database level by using ALTER DATABASE <dbname> SET PARAMETERIZATION FORCED and that might help. If neither of these help, we could periodically dump the plan cache for that database, as discussed as being a problem in Kalen’s blog post referenced above; not an ideal scenario. The other option is to increase the memory on the server to 16GB or 32GB, if the hardware allows it, which will increase the size of the plan cache as well as the buffer cache. In SQL Server 2005 SP1, on a system with 16GB of memory, if we set max server memory to 14GB the plan cache could use at most 9GB  [(8GB*.75)+(6GB*.5)=(6+3)=9GB], leaving 5GB for the buffer cache.  If we went to 32GB of memory and set max server memory to 28GB, the plan cache could use at most 16GB [(8*.75)+(20*.5)=(6+10)=16GB], leaving 12GB for the buffer cache. Thankfully we have SQL Server 2005 Service Pack 2, 3, and 4 these days which include the changes in plan cache sizing discussed in the Changes to Caching Behavior between SQL Server 2000, SQL Server 2005 RTM and SQL Server 2005 SP2 blog post. In real life, when I was troubleshooting this problem, I spent a week trying to chase down the cause of the disk I/O bottleneck with our Server Admin and SAN Admin, and there wasn’t much that could be done immediately there, so I finally asked if we could increase the memory on the server to 16GB, which did fix the problem. It wasn’t until I had this same problem occur on another system that I actually figured out how to really troubleshoot this down to the root cause.  I couldn’t believe the size of the plan cache on the server with 16GB of memory when I actually learned about this and went back to look at it. SQL Server is constantly telling a story to anyone that will listen. As the DBA, you have to sit back and listen to all that it’s telling you and then evaluate the big picture and how all the data you can gather from SQL about performance relate to each other. One of the greatest tools out there is actually a free in the form of Diagnostic Scripts for SQL Server 2005 and 2008, created by MVP Glenn Alan Berry. Glenn’s scripts collect a majority of the information that SQL has to offer for rapid troubleshooting of problems, and he includes a lot of notes about what the outputs of each individual query might be telling you. When I read Pinal’s blog post SQL SERVER – ASYNC_IO_COMPLETION – Wait Type – Day 11 of 28, I noticed that he referenced Checking Memory Related Performance Counters in his post, but there was no real explanation about why checking memory counters is so important when looking at an I/O related wait type. I thought I’d chat with him briefly on Google Talk/Twitter DM and point this out, and offer a couple of other points I noted, so that he could add the information to his blog post if he found it useful.  Instead he asked that I write a guest blog for this. I am honored to be a guest blogger, and to be able to share this kind of information with the community. The information contained in this blog post is a glimpse at how I do troubleshooting almost every day of the week in my own environment. SQL Server provides us with a lot of information about how it is running, and where it may be having problems, it is up to us to play detective and find out how all that information comes together to tell us what’s really the problem. This blog post is written by Jonathan Kehayias (Blog | Twitter). Reference: Pinal Dave (http://blog.SQLAuthority.com) Filed under: MVP, Pinal Dave, PostADay, Readers Contribution, SQL, SQL Authority, SQL Query, SQL Server, SQL Tips and Tricks, SQL Wait Stats, SQL Wait Types, T SQL, Technology

  Read the article

• Queued Loadtest to remove Concurrency issues using Shared Data Service in OpenScript

  - by stefan.thieme(at)oracle.com

  Queued Processing to remove Concurrency issues in Loadtest ScriptsSome scripts act on information returned by the server, e.g. act on first item in the returned list of pending tasks/actions. This may lead to concurrency issues if the virtual users simulated in a load test scenario are not synchronized in some way.As the load test cases should be carried out in a comparable and straight forward manner simply cancel a transaction in case a collision occurs is clearly not an option. In case you increase the number of virtual users this approach would lead to a high number of requests for the early steps in your transaction (e.g. login, retrieve list of action points, assign an action point to the virtual user) but later steps would be rarely visited successfully or at all, depending on the application logic.A way to tackle this problem is to enqueue the virtual users in a Shared Data Service queue. Only the first virtual user in this queue will be allowed to carry out the critical steps (retrieve list of action points, assign an action point to the virtual user) in your transaction at any one time.Once a virtual user has passed the critical path it will dequeue himself from the head of the queue and continue with his actions. This does theoretically allow virtual users to run in parallel all steps of the transaction which are not part of the critical path.In practice it has been seen this is rarely the case, though it does not allow adding more than N users to perform a transaction without causing delays due to virtual users waiting in the queue. N being the time of the total transaction divided by the sum of the time of all critical steps in this transaction.While this problem can be circumvented by allowing multiple queues to act on individual segments of the list of actions, e.g. per country filter, ends with 0..9 filter, etc.This would require additional handling of these additional queues of slots for the virtual users at the head of the queue in order to maintain the mutually exclusive access to the first element in the list returned by the server at any one time of the load test. Such an improved handling of multiple queues and/or multiple slots is above the subject of this paper.Shared Data Services Pre-RequisitesStart WebLogic Server to host Shared Data ServicesYou will have to make sure that your WebLogic server is installed and started. Shared Data Services may not work if you installed only the minimal installation package for OpenScript. If however you installed the default package including OLT and OTM, you may follow the instructions below to start and verify WebLogic installation.To start the WebLogic Server deployed underneath of Oracle Load Testing and/or Oracle Test Manager you can go to your Start menu, Oracle Application Testing Suite and select the Restart Oracle Application Testing Suite Application Service entry from the Tools submenu.To verify the service has been started you can run the Microsoft Management Console for Services by Selecting Run from the Start Menu and entering services.msc. Look for the entry that reads Oracle Application Testing Suite Application Service, once it has changed it status from Starting to Started you can proceed to verify the login. Please note that this may take several minutes, I would say up to 10 minutes depending on the strength of your CPU horse-power.Verify WebLogic Server user credentialsYou will have to make sure that your WebLogic Server is installed and started. Next open the Oracle WebLogic Server Adminstration Console on http://localhost:8088/console.It may take a while until the application is deployed and started. It may display the following until the Administration Console has been deployed on the fly.Afterwards you can login using the username oats and the password that you selected during install time for your Application Testing Suite administrative purposes.This will bring up the Home page of you WebLogic Server. You have actually verified that you are able to login with these credentials already. However if you want to check the details, navigate to Security Realms, myrealm, Users and Groups tab.Here you could add users to your WebLogic Server which could be used in the later steps. Details on the Groups required for such a custom user to work are exceeding this quick overview and have to be selected with the WebLogic Server Adminstration Guide in mind.Shared Data Services pre-requisites for Load testingOpenScript Preferences have to be set to enable Encryption and provide a default Shared Data Service Connection for Playback.These are pre-requisites you want to use for load testing with Shared Data Services.Please note that the usage of the Connection Parameters (individual directive in the script) for Shared Data Services did not playback reliably in the current version 9.20.0370 of Oracle Load Testing (OLT) and encryption of credentials still seemed to be mandatory as well.General Encryption settingsSelect OpenScript Preferences from the View menu and navigate to the General, Encryption entry in the tree on the left. Select the Encrypt script data option from the list and enter the same password that you used for securing your WebLogic Server Administration Console.Enable global shared data access credentialsSelect OpenScript Preferences from the View menu and navigate to the Playback, Shared Data entry in the tree on the left. Enable the global shared data access credentials and enter the Address, User name and Password determined for your WebLogic Server to host Shared Data Services.Please note, that you may want to replace the localhost in Address with the hosts realname in case you plan to run load tests with Loadtest Agents running on remote systems.Queued Processing of TransactionsEnable Shared Data Services Module in Script PropertiesThe Shared Data Services Module has to be enabled for each Script that wants to employ the Shared Data Service Queue functionality in OpenScript. It can be enabled under the Script menu selecting Script Properties. On the Script Properties Dialog select the Modules section and check Shared Data to enable Shared Data Service Module for your script. Checking the Shared Data Services option will effectively add a line to your script code that adds the sharedData ScriptService to your script class of IteratingVUserScript.@ScriptService oracle.oats.scripting.modules.sharedData.api.SharedDataService sharedData;Record your scriptRecord your script as usual and then add the following things for Queue handling in the Initialize code block, before the first step and after the last step of your critical path and in the Finalize code block.The java code to be added at individual locations is explained in the following sections in full detail.Create a Shared Data Queue in InitializeTo create a Shared Data Queue go to the Java view of your script and enter the following statements to the initialize() code block.info("Create queueA with life time of 120 minutes");sharedData.createQueue("queueA", 120);This will create an instantiation of the Shared Data Queue object named queueA which is maintained for upto 120 minutes.If you want to use the code for multiple scripts, make sure to use a different queue name for each one here and in the subsequent steps. You may even consider to use a dynamic queueName based on filters of your result list being concurrently accessed.Prepare a unique id for each IterationIn order to keep track of individual virtual users in our queue we need to create a unique identifier from the virtual user id and the used username right after retrieving the next record from our databank file.getDatabank("Usernames").getNextDatabankRecord();getVariables().set("usernameValue1","VU_{{@vuid}}_{{@iterationnum}}_{{db.Usernames.Username}}_{{@timestamp}}_{{@random(10000)}}");String usernameValue = getVariables().get("usernameValue1");info("Now running virtual user " + usernameValue);As you can see from the above code block, we have set the OpenScript variable usernameValue1 to VU_{{@vuid}}_{{@iterationnum}}_{{db.Usernames.Username}}_{{@timestamp}}_{{@random(10000)}} which is a concatenation of the virtual user id and the iterationnumber for general uniqueness; as well as the username from our databank, the timestamp and a random number for making it further unique and ease spotting of errors.Not all of these fields are actually required to make it really unique, but adding the queue name may also be considered to help troubleshoot multiple queues.The value is then retrieved with the getVariables.get() method call and assigned to the usernameValue String used throughout the script.Please note that moving the getDatabank("Usernames").getNextDatabankRecord(); call to the initialize block was later considered to remove concurrency of multiple virtual users running with the same userid and therefor accessing the same "My Inbox" in step 6. This will effectively give each virtual user a userid from the databank file. Make sure you have enough userids to remove this second hurdle.Enqueue and attend Queue before Critical PathTo maintain the right order of virtual users being allowed into the critical path of the transaction the following pseudo step has to be added in front of the first critical step. In the case of this example this is right in front of the step where we retrieve the list of actions from which we select the first to be assigned to us.beginStep("[0] Waiting in the Queue", 0);{info("Enqueued virtual user " + usernameValue + " at the end of queueA");sharedData.offerLast("queueA", usernameValue);info("Wait until the user is the first in queueA");String queueValue1 = null;do {// we wait for at least 0.7 seconds before we check the head of the// queue. This is the time it takes one user to move through the// critical path, i.e. pass steps [5] Enter country and [6] Assign// to meThread.sleep(700);queueValue1 = (String) sharedData.peekFirst("queueA");info("The first user in queueA is currently: '" + queueValue1 + "' " + queueValue1.getClass() + " length " + queueValue1.length() );info("The current user is '"+ usernameValue + "' " + usernameValue.getClass() + " length " + usernameValue.length() + ": indexOf " + usernameValue.indexOf(queueValue1) + " equals " + usernameValue.equals(queueValue1) );} while ( queueValue1.indexOf(usernameValue) < 0 );info("Now the user is the first in queueA");}endStep();This will enqueue the username to the tail of our Queue. It will will wait for at least 700 milliseconds, the time it takes for one user to exit the critical path and then compare the head of our queue with it's username. This last step will be repeated while the two are not equal (indexOf less than zero). If they are equal the indexOf will yield a value of zero or larger and we will perform the critical steps.Dequeue after Critical PathAfter the virtual user has left the critical path and complete its last step the following code block needs to dequeue the virtual user. In the case of our example this is right after the action has been actually assigned to the virtual user. This will allow the next virtual user to retrieve the list of actions still available and in turn let him make his selection/assignment.info("Get and remove the current user from the head of queueA");String pollValue1 = (String) sharedData.pollFirst("queueA");The current user is removed from the head of the queue. The next one will now be able to match his username against the head of the queue.Clear and Destroy Queue for FinishWhen the script has completed, it should clear and destroy the queue. This code block can be put in the finish block of your script and/or in a separate script in order to clear and remove the queue in case you have spotted an error or want to reset the queue for some reason.info("Clear queueA");sharedData.clearQueue("queueA");info("Destroy queueA");sharedData.destroyQueue("queueA");The users waiting in queueA are cleared and the queue is destroyed. If you have scripts still executing they will be caught in a loop.I found it better to maintain a separate Reset Queue script which contained only the following code in the initialize() block. I use to call this script to make sure the queue is cleared in between multiple Loadtest runs. This script could also even be added as the first in a larger scenario, which would execute it only once at very start of the Loadtest and make sure the queues do not contain any stale entries.info("Create queueA with life time of 120 minutes");sharedData.createQueue("queueA", 120);info("Clear queueA");sharedData.clearQueue("queueA");This will create a Shared Data Queue instance of queueA and clear all entries from this queue.Monitoring QueueWhile creating the scripts it was useful to monitor the contents, i.e. the current first user in the Queue. The following code block will make sure the Shared Data Queue is accessible in the initialize() block.info("Create queueA with life time of 120 minutes");sharedData.createQueue("queueA", 120);In the run() block the following code will continuously monitor the first element of the Queue and write an informational message with the current username Value to the Result window.info("Monitor the first users in queueA");String queueValue1 = null;do {queueValue1 = (String) sharedData.peekFirst("queueA");if (queueValue1 != null)info("The first user in queueA is currently: '" + queueValue1 + "' " + queueValue1.getClass() + " length " + queueValue1.length() );} while ( true );This script can be run from OpenScript parallel to a loadtest performed by the Oracle Load Test.However it is not recommend to run this in a production loadtest as the performance impact is unknown. Accessing the Queue's head with the peekFirst() method has been reported with about 2 seconds response time by both OpenScript and OTL. It is advised to log a Service Request to see if this could be lowered in future releases of Application Testing Suite, as the pollFirst() and even offerLast() writing to the tail of the Queue usually returned after an average 0.1 seconds.Debugging QueueWhile debugging the scripts the following was useful to remove single entries from its head, i.e. the current first user in the Queue. The following code block will make sure the Shared Data Queue is accessible in the initialize() block.info("Create queueA with life time of 120 minutes");sharedData.createQueue("queueA", 120);In the run() block the following code will remove the first element of the Queue and write an informational message with the current username Value to the Result window.info("Get and remove the current user from the head of queueA");String pollValue1 = (String) sharedData.pollFirst("queueA");info("The first user in queueA was currently: '" + pollValue1 + "' " + pollValue1.getClass() + " length " + pollValue1.length() );ReferencesOracle Functional Testing OpenScript User's Guide Version 9.20 [E15488-05]Chapter 17 Using the Shared Data Modulehttp://download.oracle.com/otn/nt/apptesting/oats-docs-9.21.0030.zipOracle Fusion Middleware Oracle WebLogic Server Administration Console Online Help 11g Release 1 (10.3.4) [E13952-04]Administration Console Online Help - Manage users and groupshttp://download.oracle.com/docs/cd/E17904_01/apirefs.1111/e13952/taskhelp/security/ManageUsersAndGroups.htm

  Read the article

• top tweets WebLogic Partner Community – October 2012

  - by JuergenKress

  Send your tweets @wlscommunity #WebLogicCommunity and follow us at http://twitter.com/wlscommunity WebLogic Community?@wlscommunity Real World Java EE Patterns by Adam Bien http://wp.me/p1LMIb-mp Markus Eisele?@myfear #JavaOne Content Available for Free https://blogs.oracle.com/java/entry/javaone_content_available_for_free … /via @java Adam Bien?@AdamBien Thought that 1h screencast is way too long to be popular. I was wrong. Lightweight Java EE is doing very well: http://www.adam-bien.com/roller/abien/entry/lightweight_java_ee_screencast … OracleBlogs?@OracleBlogs COLLABORATE 13 Call for Papers http://ow.ly/2szPuZ Oracle WebLogic?@OracleWebLogic New Blog Post: Data Source Security Part 1 http://ow.ly/2szFbv Markus Eisele?@myfear My Three Days at #JavaOne 2012 http://yakovfain.com/2012/10/04/my-three-days-at-javaone-2012/ … < nice writeup ;) Adam Bien?@AdamBien JavaOne 2012 Announcements And Surprises: NetBeans 7.3+ comes with HTML 5, JavaScript, CSS 3 support. JavaScript... http://bit.ly/Uy14eD Andrejus Baranovskis?@andrejusb OOW'12: Oracle ADF Implementations Around the Globe: Best Practices http://fb.me/1IVg6gzU0 gschmutz?@gschmutz Just published a blog with a wrap-up of my presentations at OOW 2012. https://guidoschmutz.wordpress.com/2012/10/07/my-presentations-at-oracle-open-world-2012/ … #oow2012 #trivadis Andrejus Baranovskis?@andrejusb OOW'12: Oracle Business Process Management/Oracle ADF Integration Best Practices http://fb.me/1GY3nz1lb WebLogic Community?@wlscommunity ExaLogic 2.01 ppt & training & Installation check-list & tips & Web tier roadmap http://wp.me/p1LMIb-mh Adam Bien?@AdamBien JavaOne 2012, First Feedback and The Strange Thing: NetBeans day was surprising well attended. A big room was fu... http://bit.ly/PwWwx8 OracleSupport_WLS?@weblogicsupport Free registration for our next webcast on setting up and using a #weblogic #cluster http://pub.vitrue.com/xWV8 WebLogic Community?@wlscommunity UKOUG Application Server & Middleware SIG Meeting http://wp.me/p1LMIb-mC Ronald Luttikhuizen?@rluttikhuizen Discussing future plans for Oracle Middleware Infrastructure Group with @simon_haslam @Jphjulstad and Rene van Wijk #oow @wlscommunity JAX London?@jaxlondon Be part of #JAXLondon- only 11 days to go! Still need a ticket? http://buff.ly/TUPKmL WebLogic Community?@wlscommunity ExaLogic X3-2 launched at OOW 2012 http://wp.me/p1LMIb-mM WebLogic Community?@wlscommunity @OracleEvents Dear Oracle Team thanks for promoting the WebLogic bootcamp, new schedules are online https://blogs.oracle.com/emeapartnerweblogic/resource/weblogic12c.htm … #weblogiccommunity OracleBlogs?@OracleBlogs Partner Webcast Introducing Oracle Business Activity Monitoring - 18 October 2012 http://ow.ly/2svzyz AMIS, Oracle & Java?@AMIS_Services Grant posted a nice little video on youtube about the #ADF EMG activities during Oracle Open World. http://youtu.be/qZhtBqnK-Zc GlassFish?@glassfish ADF Essentials - Available for free and certified on GlassFish!: If you are an Oracle customer, you are probably... http://bit.ly/UCtVwY OracleBlogs?@OracleBlogs WebLogic 12 hands-on bootcamps for partnersnew dates & locations http://ow.ly/2smOfs Pieter Kranenburg?@pskranenburg I'm EXA and I know IT! How about you? Go to http://bit.ly/OnSlDd and find out! (you might win an #iphone5 ;-) #OOW please RT Andrejus Baranovskis?@andrejusb Enabling WebLogic Administrator Group Inside Custom ADF Application http://fb.me/2d5SCeJ2g Michel Schildmeijer?@MNEMONIC01 I'm EXA and I know IT! How about you? Go to http://bit.ly/OnSlDd (you might win an #iphone5 ;-) #oow OracleSupport_WLS?@weblogicsupport Step-by-step instructions on how to configure mail Alerts in #OEM 11g for #WebLogic Servers up/down status http://pub.vitrue.com/KpZq Jeff West?@jeffreyawest Answer: Deliver JMS message to a single node in a Weblogic Cluster with a Distributed Topic http://stackoverflow.com/a/12396492/697114?stw=2 … Java?@java Bucharest Java User Group: Launched and Growing! #JUG http://ow.ly/dDnbN OracleSupport_WLS?@weblogicsupport Don't shoot the messenger! #Java source code analyzer @ http://pub.vitrue.com/Cy2J JAX London?@jaxlondon .@BrianGoetz gives in depth session on the details of how #Lambda expressions are implemented in the #Java language at #JAXLondon" ADF Community DE?@ADFCommunityDE Webcast ADFNewsSession: ADF as a basis of Fusion Apps - the biggest ADF project ever. Sep 14, 8:30 AM CET. Dial in https://blogs.oracle.com/jdevotnharvest/entry/adf_partner_community_news_session … OracleBlogs?@OracleBlogs WebLogic & Coherence & Cloud presentations for customer meetings http://ow.ly/1mqwrC Pieter Kranenburg?@pskranenburg Seminar: Oracle WebLogic 12c at Qualogy. You are invited! http://bit.ly/Ps9LDF Oracle WebLogic?@OracleWebLogic New Blog Post: Oracle OpenWorld Update -- General Session: Oracle Fusion Middleware Strategies Driving Business Inno... http://ow.ly/2stylf Oracle Cloud Zone?@OracleCloudZone New partner programs for Oracle Cloud Solutions http://bit.ly/PrVq5O #cloud #oow Lucas Jellema?@lucasjellema The strategy on Java - JEE, SE, ME, FX: http://technology.amis.nl/2012/10/02/javaone-2012-strategy-and-technical-keynote/ … #javaone #oow_amis WebLogic Community?@wlscommunity Send your #WebLogicCommunity #oow pictures and blog posts @wlscommunity or http://www.facebook.com/weblogiccommunity … Enjoy OOW ;-) WebLogic Community?@wlscommunity Become an WebLogic 12c expert, attend our partner bootcampshttps://blogs.oracle.com/emeapartnerweblogic/resource/weblogic12c.htm … #WebLogicCommunity #opn AMIS, Oracle & Java?@AMIS_Services Volgende #oracle #ADF training bij @AMIS_SERVICES is van 12 tot 16 november. Meer info of aanmelden? http://www.amis.nl/Trainingen/oracle-adf-11g-applicatieontwikkeling/ … Devoxx?@Devoxx ALL the Devoxx 2011 talks are now freely available on Parleys @ http://www.parleys.com/#st=4&id=102998 Pls RT! Adam Bien?@AdamBien Use the coupon code "PLUMA" and you will get 20% off for "Real World Java EE Patterns": http://realworldpatterns.com Lucas Jellema?@lucasjellema Very good summary of the #JavaOne Technical Keynote last night: http://java.dzone.com/articles/javaone-2012-javaone-technical … Arun Gupta?@arungupta Blogged: JavaOne 2012 Keynote and GlassFish Party Pictures: Some pictures from the keynote ... And som... http://bit.ly/ViH0ue Lucas Jellema?@lucasjellema Most recent promoted build for GassFish 4.0 (EE7) has WebSocket support: to play with: http://dlc.sun.com.edgesuite.net/glassfish/4.0/promoted/ … #javaone michael palmeter?@michaelpalmeter If you haven't seen the 5-minute Exalogic demo, you need to (do it now!) - http://lnkd.in/GRqy3x Lonneke Dikmans?@lonnekedikmans VENNSTER BLOG: Running EclipseLink DBWS 2.4.0 on GlassFish 3.1.2 http://blog.vennster.nl/2012/09/running-eclipselink-dbws-240-on.html?spref=tw … WebLogic Community?@wlscommunity WebLogic Partner Community Newsletter September 2012 http://wp.me/p1LMIb-mf WebLogic Community?@wlscommunity again again again&hellip;. it is Oracle Open World 2012 http://wp.me/p1LMIb-m6 Markus Eisele?@myfear #WebLogic and #JavaEE Roadmap and Strategy Session at OOW http://ow.ly/2slZEY /via @OracleWebLogic Adam Bien?@AdamBien An Article About Java EE Connector Architectures 1.6 (JCA 1.6): The free Java Magazine article: Java EE Connect... http://bit.ly/St6sxq Lucas Jellema?@lucasjellema ADF Essentials - free to develop and to deploy (I said: free!) - http://www.oracle.com/technetwork/developer-tools/adf/overview/adfessentials-1719844.html … AMIS, Oracle & Java?@AMIS_Services Blog by Lucas Jellema: "Develop and Deploy ADF applications – free of charge using the new ADF Essentials" http://bit.ly/StAhxY Andrejus Baranovskis?@andrejusb ADF Essentials - Quick Technical Review http://fb.me/2hKCXyF43 OracleBlogs?@OracleBlogs GlassFish Extension for Oracle JDeveloper http://ow.ly/2slIO8 Retweetet von WebLogic Community Oracle Eclipse?@OEPE New Tutorial: Using ADF Faces and ADF Controller with Oracle Enterprise Pack for Eclipse. #OEPE http://pub.vitrue.com/QoUg Simon Haslam?@simon_haslam As of the last day or two there's a new Java Products Media Pack on http://edelivery.oracle.com (rather than it being in FMW pack) WebLogic Community?@wlscommunity top tweets WebLogic Partner Community &ndash; September 2012 http://wp.me/p1LMIb-m2 Adam Bien?@AdamBien I was interviewed by OTN: http://www.oracle.com/technetwork/articles/java/jaxawards-1843595.html …See you at JavaOne! Oracle WebLogic?@OracleWebLogic DevOps Basics for #WebLogic: Track Down High CPU Thread with ps, top and the new JDK7 jcmd tool. Great blog @frankmuz. http://ow.ly/dOBM4 Simon Haslam?@simon_haslam Looking for "oak style"(!) advanced content but you're a middleware specialist? See #ukoug2012 #middlewaresunday http://2012.ukoug.org/default.asp?p=9355 … Julien Ponge ?@jponge Just finished Java EE 6 + AngularJS samples for my upcoming middleware lectures. Code at https://github.com/jponge/todoapp-javaee6-angularjs … and https://github.com/jponge/todoapp-bosswatch … Markus Eisele?@myfear #Oracle #WebLogic is now totally #FREE for #Developer - more than just OTN license to develop the 1st prototype! http://bit.ly/SWltsR Markus Eisele?@myfear #WebSockets on #WebLogic Server http://ow.ly/1mv4QP by @wlsteve < need to give this a testdrive ;) OracleEnterpriseMgr?@oracle_em EM Blog : Oracle Enterprise Manager Cloud Control 12c Release 2 (12.1.0.2) is Available Now ! #em12c http://pub.vitrue.com/mk7o OracleBlogs?@OracleBlogs ADF training material now on the iPad http://ow.ly/1mqz1Q GlassFish?@glassfish GlassFish grows by 50% in Software Stack Market Share Report for August 2012 by @Jelastic http://awe.sm/o4ZAp WebLogic Partner Community For regular information become a member in the WebLogic Partner Community please visit: http://www.oracle.com/partners/goto/wls-emea ( OPN account required). If you need support with your account please contact the Oracle Partner Business Center. Blog Twitter LinkedIn Mix Forum Wiki Technorati Tags: twitter,WebLogic,WebLogic Community,Oracle,OPN,Jürgen Kress

  Read the article

< Previous Page | 216 217 218 219 220 221 222 223 224 225 226  | Next Page >