Search Results

Search found 55308 results on 2213 pages for 'http max age'.

Page 220/2213 | < Previous Page | 216 217 218 219 220 221 222 223 224 225 226 227  | Next Page >

• Spanning-tree setup with incompatible switches

  - by wfaulk

  I have a set of eight HP ProCurve 2910al-48G Ethernet switches at my datacenter that are set up in a star topology with no physical loops. I want to partially mesh the switches for redundancy and manage the loops with a spanning-tree protocol. However, our connection to the datacenter is provided by two uplinks, each to a Cisco 3750. The datacenter's switches are handling the redundant connection using PVST spanning-tree, which is a Cisco-proprietary spanning-tree implementation that my HP switches do not support. It appears that my switches are not participating in the datacenter's spanning-tree domain, but are blindly passing the BPDUs between the two switchports on my side, which enables the datacenter's switches to recognize the loop and put one of the uplinks into the Blocking state. This is somewhat supposition, but I can confirm that, while my switches say that both of the uplink ports are forwarding, only one is passing any real quantity of data. (I am assuming that I cannot get the datacenter to move away from PVST. I don't know that I'd want them to make that significant of a change anyway.) The datacenter has also sent me this output from their switches (which I have expurgated of any identifiable info): 3750G-1#sh spanning-tree vlan nnn VLAN0nnn Spanning tree enabled protocol ieee Root ID Priority 10 Address 00d0.0114.xxxx Cost 4 Port 5 (GigabitEthernet1/0/5) Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Bridge ID Priority 32mmm (priority 32768 sys-id-ext nnn) Address 0018.73d3.yyyy Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Aging Time 300 sec Interface Role Sts Cost Prio.Nbr Type ------------------- ---- --- --------- -------- -------------------------------- Gi1/0/5 Root FWD 4 128.5 P2p Gi1/0/6 Altn BLK 4 128.6 P2p Gi1/0/8 Altn BLK 4 128.8 P2p and: 3750G-2#sh spanning-tree vlan nnn VLAN0nnn Spanning tree enabled protocol ieee Root ID Priority 10 Address 00d0.0114.xxxx Cost 4 Port 6 (GigabitEthernet1/0/6) Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Bridge ID Priority 32mmm (priority 32768 sys-id-ext nnn) Address 000f.f71e.zzzz Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Aging Time 300 sec Interface Role Sts Cost Prio.Nbr Type ------------------- ---- --- --------- -------- -------------------------------- Gi1/0/1 Desg FWD 4 128.1 P2p Gi1/0/5 Altn BLK 4 128.5 P2p Gi1/0/6 Root FWD 4 128.6 P2p Gi1/0/8 Desg FWD 4 128.8 P2p The uplinks to my switches are on Gi1/0/8 on both of their switches. The uplink ports are configured with a single tagged VLAN. I am also using a number of other tagged VLANs in my switch infrastructure. And, to be clear, I am passing the tagged VLAN I'm receiving from the datacenter to other ports on other switches in my infrastructure. My question is: how do I configure my switches so that I can use a spanning tree protocol inside my switch infrastructure without breaking the datacenter's spanning tree that I cannot participate in?

  Read the article

• LFTP when used with proxies doesn't work

  - by user2949465

  can't seem to use LFTP with proxies that require authentification correctly on my Ubuntu server. When I use it with proxy that doesn't require username/password everything seems fine: lftp lftp :~> set http:proxy http://HOST:PORT lftp :~> set ftp:proxy http://HOST:PORT lftp :~> open username:[email protected] lftp [email protected]:~> get file.ext file.ext 36352 bytes transferred in 10 seconds (3.5K/s) lftp [email protected]:~> exit but when I have to put username/password there is a problem: lftp lftp :~> set http:proxy http://proxylogin:proxypass@HOST:port lftp :~> set ftp:proxy http://proxylogin:proxypass@HOST:port lftp :~> open ftp://ftpuser:[email protected] answer: cd: Access failed: 401 Authentication Required (~) please someone help!

  Read the article

• Configure apache to reverse proxy for specific name

  - by Phrogz

  I have a working intranet server that: Properly serves some content from http://hqmktgwb01/ Is currently properly configured to reverse proxy from http://hqmktgwb01/dashstats to a round-robin of localhost:3000 - localhost:3003 Also has the DNS name dashstats (going to the same IP) The current working configuration file can be found here: http://pastie.org/1426082 I would like to modify the configuration so that:    4. http://dashstats/ performs the same reverse proxying http://hqmktgwb01/dashstats. I (naively) modified the config like this: http://pastie.org/1426047 (added lines 90-98) but this is not a valid Apache config. Please help me to modify the original config file to accomplish 1-4 above.

  Read the article

• Rework filename from mod_pagespeed back to normal files

  - by British Sea Turtle

  I am hoping someone can help me with this problem. I am moving to a new server and not using mod_pagespeed any more. However We not that we have lots of external links that link to images on our server using the strange mod_pagespeed filenames. This is not an issue but we do not want to have lots of 404 errors. So I have lots of links like the following : http://www.domain.com/images/150x150xlink.png.pagespeed.ic.pPXw45HSQm.png http://www.domain.com/images/paris_01.gif.pagespeed.ce.vfrkuKUaj0.gif http://www.doamin.com/images/1st2.gif.pagespeed.ce.OUg38q6VbZ.gif How can I redirect them to : http://www.domain.com/images/150x150xlink.png http://www.domain.com/images/paris_01.gif http://www.doamin.com/images/1st2.gif There are thousands of files like this so I am hoping for a simple solution with mod_rewrite, I tried this but it does not work. So any help would be appreciated. RewriteCond %{REQUEST_URI} \.gif\.pagespeed\. [NC] RewriteRule ^(.*?\.gif)\..*\.gif$ $1 [NC,L]

  Read the article

• 403 in Response to OPTIONS when updating working copy having full access

  - by user23419

  There is an SVN repository (single repository) http://example.net/svn The repository contains several projects (directories): http://example.net/svn/Project1 http://example.net/svn/Project2 User has full access to Project1 directory and has no access neither to root nor to Project2. Everything works fine for a while: user checks out http://example.net/svn/Project1, commits and updates it successfully. But sometimes trying to update leads to the following error: Command: Update Error: Server sent unexpected return value (403 Forbidden) in response to OPTIONS Error: request for 'http://example.net/svn' Finished! Why does TortoiseSVN request something in the root??? I have noticed that this happens after somebody else committed copy or move operation. Checking out http://example.net/svn/Project1 helps till next time... The main question: How to set up access rights for user to avoid these errors? Note, it's not an option to grant user any read or write access right on the root directory for security reasons.

  Read the article

• MySQL Memory usage

  - by Rob Stevenson-Leggett

  Our MySQL server seems to be using a lot of memory. I've tried looking for slow queries and queries with no index and have halved the peak CPU usage and Apache memory usage but the MySQL memory stays constantly at 2.2GB (~51% of available memory on the server). Here's the graph from Plesk. Running top in the SSH window shows the same figures. Does anyone have any ideas on why the memory usage is constant like this and not peaks and troughs with usage of the app? Here's the output of the MySQL Tuning Primer script: -- MYSQL PERFORMANCE TUNING PRIMER -- - By: Matthew Montgomery - MySQL Version 5.0.77-log x86_64 Uptime = 1 days 14 hrs 4 min 21 sec Avg. qps = 22 Total Questions = 3059456 Threads Connected = 13 Warning: Server has not been running for at least 48hrs. It may not be safe to use these recommendations To find out more information on how each of these runtime variables effects performance visit: http://dev.mysql.com/doc/refman/5.0/en/server-system-variables.html Visit http://www.mysql.com/products/enterprise/advisors.html for info about MySQL's Enterprise Monitoring and Advisory Service SLOW QUERIES The slow query log is enabled. Current long_query_time = 1 sec. You have 6 out of 3059477 that take longer than 1 sec. to complete Your long_query_time seems to be fine BINARY UPDATE LOG The binary update log is NOT enabled. You will not be able to do point in time recovery See http://dev.mysql.com/doc/refman/5.0/en/point-in-time-recovery.html WORKER THREADS Current thread_cache_size = 0 Current threads_cached = 0 Current threads_per_sec = 2 Historic threads_per_sec = 0 Threads created per/sec are overrunning threads cached You should raise thread_cache_size MAX CONNECTIONS Current max_connections = 100 Current threads_connected = 14 Historic max_used_connections = 20 The number of used connections is 20% of the configured maximum. Your max_connections variable seems to be fine. INNODB STATUS Current InnoDB index space = 6 M Current InnoDB data space = 18 M Current InnoDB buffer pool free = 0 % Current innodb_buffer_pool_size = 8 M Depending on how much space your innodb indexes take up it may be safe to increase this value to up to 2 / 3 of total system memory MEMORY USAGE Max Memory Ever Allocated : 2.07 G Configured Max Per-thread Buffers : 274 M Configured Max Global Buffers : 2.01 G Configured Max Memory Limit : 2.28 G Physical Memory : 3.84 G Max memory limit seem to be within acceptable norms KEY BUFFER Current MyISAM index space = 4 M Current key_buffer_size = 7 M Key cache miss rate is 1 : 40 Key buffer free ratio = 81 % Your key_buffer_size seems to be fine QUERY CACHE Query cache is supported but not enabled Perhaps you should set the query_cache_size SORT OPERATIONS Current sort_buffer_size = 2 M Current read_rnd_buffer_size = 256 K Sort buffer seems to be fine JOINS Current join_buffer_size = 132.00 K You have had 16 queries where a join could not use an index properly You should enable "log-queries-not-using-indexes" Then look for non indexed joins in the slow query log. If you are unable to optimize your queries you may want to increase your join_buffer_size to accommodate larger joins in one pass. Note! This script will still suggest raising the join_buffer_size when ANY joins not using indexes are found. OPEN FILES LIMIT Current open_files_limit = 1024 files The open_files_limit should typically be set to at least 2x-3x that of table_cache if you have heavy MyISAM usage. Your open_files_limit value seems to be fine TABLE CACHE Current table_cache value = 64 tables You have a total of 426 tables You have 64 open tables. Current table_cache hit rate is 1% , while 100% of your table cache is in use You should probably increase your table_cache TEMP TABLES Current max_heap_table_size = 16 M Current tmp_table_size = 32 M Of 15134 temp tables, 9% were created on disk Effective in-memory tmp_table_size is limited to max_heap_table_size. Created disk tmp tables ratio seems fine TABLE SCANS Current read_buffer_size = 128 K Current table scan ratio = 2915 : 1 read_buffer_size seems to be fine TABLE LOCKING Current Lock Wait ratio = 1 : 142213 Your table locking seems to be fine The app is a facebook game with about 50-100 concurrent users. Thanks, Rob

  Read the article

• Rewrite request URI based on Host header in HAProxy

  - by DorinC

  I would like to set up HAProxy to forward HTTP requests to some backend servers but I need it to also rewrite the URI part based on the Host. I've read through the doc but it seems that reqirep isn't suitable for this purpose. Any idea if this is even possible with HAProxy? Here are the details of what I'm trying to accomplish: Requests that come in on: http://www.original-domain.com/ would be balanced between: http://server1/domains/www.original-domain.com/ ... http://serverN/domains/www.original-domain.com/ The proxy should be able to handle this for any number of domains (original-domain.com can be anything, it's not limited to a fixed set of values). For this to work HAProxy would need to rewrite a request like this: GET /original-uri HTTP/1.1 Host: original-domain.com to: GET /domains/original-domain.com/original-uri HTTP/1.1 Host: serverN and forward that request to one of the internal servers.

  Read the article

• Bash-Scripting - Munin Plugin don't work

  - by FTV Admin

  i have written a munin-plugin to count the http-statuscodes of lighttpd. The script: #!/bin/bash ###################################### # Munin-Script: Lighttpd-Statuscodes # ###################################### ##Config # path to lighttpd access.log LIGHTTPD_ACCESS_LOG_PATH="/var/log/lighttpd/access.log" # rows to parse in logfile (higher value incrase time to run plugin. if value to low you may get bad counting) LOG_ROWS="200000" # #munin case $1 in autoconf) # check config AVAILABLE=`ls $LIGHTTPD_ACCESS_LOG_PATH` if [ "$AVAILABLE" = "$LIGHTTPD_ACCESS_LOG_PATH" ]; then echo "yes" else echo "No: "$AVAILABLE echo "Please check your config!" fi exit 0;; config) # graph config cat <<'EOM' graph_title Lighhtpd Statuscodes graph_vlabel http-statuscodes / min graph_category lighttpd 1xx.label 1xx 2xx.label 2xx 3xx.label 3xx 4xx.label 4xx 5xx.label 5xx EOM exit 0;; esac ## calculate AVAILABLE=`ls $LIGHTTPD_ACCESS_LOG_PATH` if [ "$AVAILABLE" = "$LIGHTTPD_ACCESS_LOG_PATH" ]; then TIME_NOW=`date` CODE_1xx="0" CODE_2xx="0" CODE_3xx="0" CODE_4xx="0" CODE_5xx="0" for i in 1 2 3 4 5; do TIME5=`date +%d/%b/%Y:%k:%M --date "$TIME_NOW -"$i"min"` CODE_1xx=$(( $CODE_1xx + `tail -n $LOG_ROWS $LIGHTTPD_ACCESS_LOG_PATH | grep "$TIME5" | grep 'HTTP/1.1" 1' | grep -c " "` )) CODE_2xx=$(( $CODE_2xx + `tail -n $LOG_ROWS $LIGHTTPD_ACCESS_LOG_PATH | grep "$TIME5" | grep 'HTTP/1.1" 2' | grep -c " "` )) CODE_3xx=$(( $CODE_3xx + `tail -n $LOG_ROWS $LIGHTTPD_ACCESS_LOG_PATH | grep "$TIME5" | grep 'HTTP/1.1" 3' | grep -c " "` )) CODE_4xx=$(( $CODE_4xx + `tail -n $LOG_ROWS $LIGHTTPD_ACCESS_LOG_PATH | grep "$TIME5" | grep 'HTTP/1.1" 4' | grep -c " "` )) CODE_5xx=$(( $CODE_5xx + `tail -n $LOG_ROWS $LIGHTTPD_ACCESS_LOG_PATH | grep "$TIME5" | grep 'HTTP/1.1" 5' | grep -c " "` )) done CODE_1xx=$(( $CODE_1xx / 5 )) CODE_2xx=$(( $CODE_2xx / 5 )) CODE_3xx=$(( $CODE_3xx / 5 )) CODE_4xx=$(( $CODE_4xx / 5 )) CODE_5xx=$(( $CODE_5xx / 5 )) echo "1xx.value "$CODE_1xx echo "2xx.value "$CODE_2xx echo "3xx.value "$CODE_3xx echo "4xx.value "$CODE_4xx echo "5xx.value "$CODE_5xx else echo "1xx.value U" echo "2xx.value U" echo "3xx.value U" echo "4xx.value U" echo "5xx.value U" fi If i run the script on local machine it runs perfectly: root@server1 /etc/munin/plugins # ll lrwxrwxrwx 1 root root 45 2011-12-19 15:23 lighttpd_statuscodes -> /usr/share/munin/plugins/lighttpd_statuscodes* root@server1 /etc/munin/plugins # ./lighttpd_statuscodes autoconf yes root@server1 /etc/munin/plugins # ./lighttpd_statuscodes config graph_title Lighhtpd Statuscodes graph_vlabel http-statuscodes / min graph_category lighttpd 1xx.label 1xx 2xx.label 2xx 3xx.label 3xx 4xx.label 4xx 5xx.label 5xx root@server1 /etc/munin/plugins #./lighttpd_statuscodes 1xx.value 0 2xx.value 5834 3xx.value 1892 4xx.value 0 5xx.value 0 But Munin shows no graph: http://s1.directupload.net/images/111219/3psgq3vb.jpg I have tested the Plugin from munin-server via telnet: root@munin-server /etc/munin/plugins/ # telnet 123.123.123.123 4949 Trying 123.123.123.123... Connected to 123.123.123.123. Escape character is '^]'. # munin node at server1.cluster1 fetch lighttpd_statuscodes 1xx.value U 2xx.value U 3xx.value U 4xx.value U 5xx.value U . Connection closed by foreign host. You can see in the script that value = U only printed, when the script can't check the lighttpd's access.log. But why can't script do it, when running via munin, and when running on local machine all is ok? Is there a bug in my bash-script? I have no Idea. Thanks for helping!

  Read the article

• Ports do not open after rules appended in iptables

  - by user2699451

  I have a server that I am trying to setup for OpenVPN. I have followed all the steps, but I see that when I try to connect to it in Windows, it doesn't allow me, it just hangs on connecting, so I did a nmap scan and I see that port 1194 is not open so naturally I append the rule to open 1194 with: iptables -A INPUT -i eth0 -p tcp --dport 1194 -j ACCEPT followed by service iptables save and service iptables restart which all executed successfully. Then I try again, but it doesn't work and another nmap scan says that port 1194 is closed. Here is the iptables configuration: # Generated by iptables-save v1.4.7 on Thu Oct 31 09:47:38 2013 *nat :PREROUTING ACCEPT [27410:3091993] :POSTROUTING ACCEPT [0:0] :OUTPUT ACCEPT [5042:376160] -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE -A POSTROUTING -o eth0 -j MASQUERADE -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE -A POSTROUTING -j SNAT --to-source 41.185.26.238 -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE COMMIT # Completed on Thu Oct 31 09:47:38 2013 # Generated by iptables-save v1.4.7 on Thu Oct 31 09:47:38 2013 *filter :INPUT ACCEPT [23571:2869068] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [27558:3656524] :vl - [0:0] -A INPUT -p tcp -m tcp --dport 5252 -m comment --comment "SSH Secure" -j ACCEPT -A INPUT -p icmp -m icmp --icmp-type 8 -m state --state NEW,RELATED,ESTABLISHED -$ -A INPUT -i lo -j ACCEPT -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT -A INPUT -p tcp -m tcp --dport 22 -m comment --comment "SSH" -j ACCEPT -A INPUT -p tcp -m tcp --dport 80 -m comment --comment "HTTP" -j ACCEPT -A INPUT -p tcp -m tcp --dport 8080 -m comment --comment "HTTPS" -j ACCEPT -A INPUT -p tcp -m tcp --dport 443 -m comment --comment "HTTP Encrypted" -j ACCEP$ -A INPUT -i eth0 -p tcp -m tcp --dport 1723 -j ACCEPT -A INPUT -i eth0 -p gre -j ACCEPT -A INPUT -p udp -m udp --dport 1194 -j ACCEPT -A FORWARD -i ppp+ -o eth0 -j ACCEPT -A FORWARD -i eth0 -o ppp+ -j ACCEPT -A FORWARD -m state --state RELATED,ESTABLISHED -j ACCEPT -A FORWARD -s 10.8.0.0/24 -j ACCEPT -A FORWARD -j REJECT --reject-with icmp-port-unreachable -A OUTPUT -p icmp -m icmp --icmp-type 0 -m state --state RELATED,ESTABLISHED -j A$ COMMIT # Completed on Thu Oct 31 09:47:38 2013 and my nmap scan from: localhost: nmap localhost Starting Nmap 5.51 ( http://nmap.org ) at 2013-10-31 09:53 SAST Nmap scan report for localhost (127.0.0.1) Host is up (0.000011s latency). Other addresses for localhost (not scanned): 127.0.0.1 Not shown: 996 closed ports PORT STATE SERVICE 22/tcp open ssh 25/tcp open smtp 443/tcp open https 1723/tcp open pptp Nmap done: 1 IP address (1 host up) scanned in 0.06 seconds remote pc: nmap [server ip] Starting Nmap 6.00 ( http://nmap.org ) at 2013-10-31 09:53 SAST Nmap scan report for rla04-nix1.wadns.net (41.185.26.238) Host is up (0.025s latency). Not shown: 858 filtered ports, 139 closed ports PORT STATE SERVICE 22/tcp open ssh 443/tcp open https 8008/tcp open http Nmap done: 1 IP address (1 host up) scanned in 15.70 seconds So, I do not know what is causing this, any assistance will be appreciated! UPDATE AFTER FIRST ANSWER::: [root@RLA04-NIX1 ~]# iptables -A FORWARD -m state --state RELATED,ESTABLISHED -j ACCEPT [root@RLA04-NIX1 ~]# iptables -A FORWARD -s 10.8.0.0/24 -j ACCEPT [root@RLA04-NIX1 ~]# iptables -A FORWARD -j REJECT [root@RLA04-NIX1 ~]# iptables -t nat -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE [root@RLA04-NIX1 ~]# service iptables save iptables: Saving firewall rules to /etc/sysconfig/iptables:[ OK ] [root@RLA04-NIX1 ~]# service iptables restart iptables: Flushing firewall rules: [ OK ] iptables: Setting chains to policy ACCEPT: filter nat [ OK ] iptables: Unloading modules: [ OK ] iptables: Applying firewall rules: [ OK ] [root@RLA04-NIX1 ~]# lsof -i :1194 -bash: lsof: command not found iptables -L -n Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:5252 /* SSH Secure */ ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 8 state NEW,RELATED,ESTABLISHED ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:22 /* SSH */ ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:80 /* HTTP */ ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:8080 /* HTTPS */ ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:443 /* HTTP Encrypted */ ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:1723 ACCEPT 47 -- 0.0.0.0/0 0.0.0.0/0 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:1194 Chain FORWARD (policy ACCEPT) target prot opt source destination ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED ACCEPT all -- 10.8.0.0/24 0.0.0.0/0 REJECT all -- 0.0.0.0/0 0.0.0.0/0 reject-with icmp-port-unreachable ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED ACCEPT all -- 10.8.0.0/24 0.0.0.0/0 REJECT all -- 0.0.0.0/0 0.0.0.0/0 reject-with icmp-port-unreachable Chain OUTPUT (policy ACCEPT) target prot opt source destination ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 0 state RELATED,ESTABLISHED Chain vl (0 references) target prot opt source destination [root@RLA04-NIX1 ~]# nmap localhostt Starting Nmap 5.51 ( http://nmap.org ) at 2013-10-31 11:13 SAST remote pc nmap [server ip] Starting Nmap 6.00 ( http://nmap.org ) at 2013-10-31 11:11 SAST Nmap scan report for rla04-nix1.wadns.net (41.185.26.238) Host is up (0.020s latency). Not shown: 858 filtered ports, 139 closed ports PORT STATE SERVICE 22/tcp open ssh 443/tcp open https 8008/tcp open http Nmap done: 1 IP address (1 host up) scanned in 4.18 seconds localhost nmap localhost Starting Nmap 5.51 ( http://nmap.org ) at 2013-10-31 11:13 SAST Nmap scan report for localhost (127.0.0.1) Host is up (0.000011s latency). Other addresses for localhost (not scanned): 127.0.0.1 Not shown: 996 closed ports PORT STATE SERVICE 22/tcp open ssh 25/tcp open smtp 443/tcp open https 1723/tcp open pptp Nmap done: 1 IP address (1 host up) scanned in 0.06 seconds UPDATE AFTER SCANNING UDP PORTS Sorry, I am noob, I am still learning, but here is the output for: nmap -sU [server ip] Starting Nmap 6.00 ( http://nmap.org ) at 2013-10-31 11:33 SAST Nmap scan report for [server address] ([server ip]) Host is up (0.021s latency). Not shown: 997 open|filtered ports PORT STATE SERVICE 53/udp closed domain 123/udp closed ntp 33459/udp closed unknown Nmap done: 1 IP address (1 host up) scanned in 8.57 seconds btw, no changes have been made since post started (except for iptables changes)

  Read the article

• Nginx proxy cache (proxy_pass $request_uri;)

  - by imastar

  I need to create proxy web using nginx. If I access http://myweb.com/http://www.target.com/ the proxy_pass should be http://www.target.com/ Here is my configuration: location / { proxy_pass $request_uri; proxy_cache_methods GET; proxy_set_header Referer "$request_uri"; proxy_redirect off; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_ignore_headers Cache-Control; proxy_hide_header Pragma; proxy_hide_header Set-Cookie; proxy_set_header Cache-Control Public; proxy_cache cache; proxy_cache_valid 200 10h; proxy_cache_valid 301 302 1h; proxy_cache_valid any 1h; } Here is the log error 2013/02/05 12:58:51 [error] 2118#0: *8 invalid URL prefix in "/http://www.target.com/", client: 108.59.8.83, server: myweb.com, request: "HEAD /http://www.target.com/ HTTP/1.1", host: "myweb.com"

  Read the article

• HAProxy NGInx SSL setup

  - by Niclas

  I've been looking around different setups for a server cluster supporting SSL and I would like to benchmark my idea with you. Requirements: All servers in the cluster should be under the same full domain name. (http and https) Routing to subsystems is done on URI matching in HA proxy. All URIs have support for SSL support. Wish: Centralizing routing rules ---<----http-----<-- | | Inet -->HA--+---https--->NGInx_SSL_1..N | | +---http---> Apache_1..M | +---http---> NodeJS Idea: Configure HA to route all SSL traffic (mode=tcp,algorithm=Source) to an NGInx cluster turning https traffic into http. Re-pass the http traffic from NGInx to the HA for normal load-balancing which performs load balancing based on HA config. My question is simply: Is this the best way to to configure based on requirements above?

  Read the article

• In Exim, is RBL spam rejected prior to being scanned by SpamAssassin?

  - by user955664

  I've recently been battling spam issues on our mail server. One account in particular was getting hammered with incoming spam. SpamAssassin's memory use is one of our concerns. What I've done is enable RBLs in Exim. I now see many rejection notices in the Exim log based on the various RBLs, which is good. However, when I run Eximstats, the numbers seem to be the same as they were prior to the enabling of the RBLs. I am assuming because the email is still logged in some way prior to the rejection. Is that what's happening, or am I missing something else? Does anyone know if these emails are rejected prior to being processed by SpamAssassin? Or does anyone know how I'd be able to find out? Is there a standard way to generate SpamAssassin stats, similar to Eximstats, so that I could compare the numbers? Thank you for your time and any advice. Edit: Here is the ACL section of my Exim configuration file ###################################################################### # ACLs # ###################################################################### begin acl # ACL that is used after the RCPT command check_recipient: # to block certain wellknown exploits, Deny for local domains if # local parts begin with a dot or contain @ % ! / | deny domains = +local_domains local_parts = ^[.] : ^.*[@%!/|] # to restrict port 587 to authenticated users only # see also daemon_smtp_ports above accept hosts = +auth_relay_hosts condition = ${if eq {$interface_port}{587} {yes}{no}} endpass message = relay not permitted, authentication required authenticated = * # allow local users to send outgoing messages using slashes # and vertical bars in their local parts. # Block outgoing local parts that begin with a dot, slash, or vertical # bar but allows them within the local part. # The sequence \..\ is barred. The usage of @ % and ! is barred as # before. The motivation is to prevent your users (or their virii) # from mounting certain kinds of attacks on remote sites. deny domains = !+local_domains local_parts = ^[./|] : ^.*[@%!] : ^.*/\\.\\./ # local source whitelist # accept if the source is local SMTP (i.e. not over TCP/IP). # Test for this by testing for an empty sending host field. accept hosts = : # sender domains whitelist # accept if sender domain is in whitelist accept sender_domains = +whitelist_domains # sender hosts whitelist # accept if sender host is in whitelist accept hosts = +whitelist_hosts accept hosts = +whitelist_hosts_ip # envelope senders whitelist # accept if envelope sender is in whitelist accept senders = +whitelist_senders # accept mail to postmaster in any local domain, regardless of source accept local_parts = postmaster domains = +local_domains # accept mail to abuse in any local domain, regardless of source accept local_parts = abuse domains = +local_domains # accept mail to hostmaster in any local domain, regardless of source accept local_parts = hostmaster domains =+local_domains # OPTIONAL MODIFICATIONS: # If the page you're using to notify senders of blocked email of how # to get their address unblocked will use a web form to send you email so # you'll know to unblock those senders, then you may leave these lines # commented out. However, if you'll be telling your senders of blocked # email to send an email to [email protected], then you should # replace "errors" with the left side of the email address you'll be # using, and "example.com" with the right side of the email address and # then uncomment the second two lines, leaving the first one commented. # Doing this will mean anyone can send email to this specific address, # even if they're at a blocked domain, and even if your domain is using # blocklists. # accept mail to [email protected], regardless of source # accept local_parts = errors # domains = example.com # deny so-called "legal" spammers" deny message = Email blocked by LBL - to unblock see http://www.example.com/ # only for domains that do want to be tested against RBLs domains = +use_rbl_domains sender_domains = +blacklist_domains # deny using hostname in bad_sender_hosts blacklist deny message = Email blocked by BSHL - to unblock see http://www.example.com/ # only for domains that do want to be tested against RBLs domains = +use_rbl_domains hosts = +bad_sender_hosts # deny using IP in bad_sender_hosts blacklist deny message = Email blocked by BSHL - to unblock see http://www.example.com/ # only for domains that do want to be tested against RBLs domains = +use_rbl_domains hosts = +bad_sender_hosts_ip # deny using email address in blacklist_senders deny message = Email blocked by BSAL - to unblock see http://www.example.com/ domains = +use_rbl_domains senders = +blacklist_senders # By default we do NOT require sender verification. # Sender verification denies unless sender address can be verified: # If you want to require sender verification, i.e., that the sending # address is routable and mail can be delivered to it, then # uncomment the next line. If you do not want to require sender # verification, leave the line commented out #require verify = sender # deny using .spamhaus deny message = Email blocked by SPAMHAUS - to unblock see http://www.example.com/ # only for domains that do want to be tested against RBLs domains = +use_rbl_domains dnslists = sbl.spamhaus.org # deny using ordb # deny message = Email blocked by ORDB - to unblock see http://www.example.com/ # # only for domains that do want to be tested against RBLs # domains = +use_rbl_domains # dnslists = relays.ordb.org # deny using sorbs smtp list deny message = Email blocked by SORBS - to unblock see http://www.example.com/ # only for domains that do want to be tested against RBLs domains = +use_rbl_domains dnslists = dnsbl.sorbs.net=127.0.0.5 # Next deny stuff from more "fuzzy" blacklists # but do bypass all checking for whitelisted host names # and for authenticated users # deny using spamcop deny message = Email blocked by SPAMCOP - to unblock see http://www.example.com/ hosts = !+relay_hosts domains = +use_rbl_domains !authenticated = * dnslists = bl.spamcop.net # deny using njabl deny message = Email blocked by NJABL - to unblock see http://www.example.com/ hosts = !+relay_hosts domains = +use_rbl_domains !authenticated = * dnslists = dnsbl.njabl.org # deny using cbl deny message = Email blocked by CBL - to unblock see http://www.example.com/ hosts = !+relay_hosts domains = +use_rbl_domains !authenticated = * dnslists = cbl.abuseat.org # deny using all other sorbs ip-based blocklist besides smtp list deny message = Email blocked by SORBS - to unblock see http://www.example.com/ hosts = !+relay_hosts domains = +use_rbl_domains !authenticated = * dnslists = dnsbl.sorbs.net!=127.0.0.6 # deny using sorbs name based list deny message = Email blocked by SORBS - to unblock see http://www.example.com/ domains =+use_rbl_domains # rhsbl list is name based dnslists = rhsbl.sorbs.net/$sender_address_domain # accept if address is in a local domain as long as recipient can be verified accept domains = +local_domains endpass message = "Unknown User" verify = recipient # accept if address is in a domain for which we relay as long as recipient # can be verified accept domains = +relay_domains endpass verify=recipient # accept if message comes for a host for which we are an outgoing relay # recipient verification is omitted because many MUA clients don't cope # well with SMTP error responses. If you are actually relaying from MTAs # then you should probably add recipient verify here accept hosts = +relay_hosts accept hosts = +auth_relay_hosts endpass message = authentication required authenticated = * deny message = relay not permitted # default at end of acl causes a "deny", but line below will give # an explicit error message: deny message = relay not permitted # ACL that is used after the DATA command check_message: accept

  Read the article

• Using Default Document with Forms Authentication

  - by John Rabotnik

  I have a site hosted on IIS7 with a default document specified as default.aspx. This works fine but my app uses Forms Authentication and I want to disable Anonymous Authentication completely. When I do disable anonymous authentication for everything except the login page, everything works fine but the default document setting stops working. With Anonymous authentication switched on if I visit http://mysite I get passed to http://mysite/default.aspx (which then redirects to the login page if the user hasn't already logged in) If I disable anonymous authentication (leaving only forms based auth enabled) and I visit http://mysite I get a permission denied page from IIS. Yet, if I visit http://mysite/default.aspx directly then the site works fine. I just want to disable anonymous authentication and have http://mysite go to http://mysite/default.aspx. Any ideas would be greatly appreciated.

  Read the article

• CPU Utilization LAMP stack

  - by Max

  We've got an ec2 m2.4xlarge running Magento (centos 5.6, httpd 2.2, php 5.2.17 with eaccelerator 0.9.5.3, mysql 5.1.52). Right now we're getting a large traffic spike, and our top looks like this: top - 09:41:29 up 31 days, 1:12, 1 user, load average: 120.01, 129.03, 113.23 Tasks: 1190 total, 18 running, 1172 sleeping, 0 stopped, 0 zombie Cpu(s): 97.3%us, 1.8%sy, 0.0%ni, 0.5%id, 0.0%wa, 0.0%hi, 0.0%si, 0.4%st Mem: 71687720k total, 36898928k used, 34788792k free, 49692k buffers Swap: 880737784k total, 0k used, 880737784k free, 1586524k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 2433 mysql 15 0 23.6g 4.5g 7112 S 564.7 6.6 33607:34 mysqld 24046 apache 16 0 411m 65m 28m S 26.4 0.1 0:09.05 httpd 24360 apache 15 0 410m 60m 25m S 26.4 0.1 0:03.65 httpd 24993 apache 16 0 410m 57m 21m S 26.1 0.1 0:01.41 httpd 24838 apache 16 0 428m 74m 20m S 24.8 0.1 0:02.37 httpd 24359 apache 16 0 411m 62m 26m R 22.3 0.1 0:08.12 httpd 23850 apache 15 0 411m 64m 27m S 16.8 0.1 0:14.54 httpd 25229 apache 16 0 404m 46m 17m R 10.2 0.1 0:00.71 httpd 14594 apache 15 0 404m 63m 34m S 8.4 0.1 1:10.26 httpd 24955 apache 16 0 404m 50m 21m R 8.4 0.1 0:01.66 httpd 24313 apache 16 0 399m 46m 22m R 8.1 0.1 0:02.30 httpd 25119 apache 16 0 411m 59m 23m S 6.8 0.1 0:01.45 httpd Questions: Would giving msyqld more memory help it cache queries and react faster? If so, how? Other than splitting mysql and php to separate servers (which we're about to do) is there anything else we could/should be doing? Thanks! UPDATE: Here's our my.cnf along with the output of mysqltuner. It looks like a cache problem. Thanks again! # cat /etc/my.cnf [client] port = **** socket = /var/lib/mysql/mysql.sock [mysqld] datadir=/mnt/persistent/mysql port=**** socket=/var/lib/mysql/mysql.sock key_buffer = 512M max_allowed_packet = 64M table_cache = 1024 sort_buffer_size = 8M read_buffer_size = 4M read_rnd_buffer_size = 2M myisam_sort_buffer_size = 64M thread_cache_size = 128M tmp_table_size = 128M join_buffer_size = 1M query_cache_limit = 2M query_cache_size= 64M query_cache_type = 1 max_connections = 1000 thread_stack = 128K thread_concurrency = 48 log-bin=mysql-bin server-id = 1 wait_timeout = 300 innodb_data_home_dir = /mnt/persistent/mysql/ innodb_data_file_path = ibdata1:10M:autoextend innodb_buffer_pool_size = 20G innodb_additional_mem_pool_size = 20M innodb_log_file_size = 64M innodb_log_buffer_size = 8M innodb_flush_log_at_trx_commit = 1 innodb_lock_wait_timeout = 50 innodb_thread_concurrency = 48 ft_min_word_len=3 [myisamchk] ft_min_word_len=3 key_buffer = 128M sort_buffer_size = 128M read_buffer = 2M write_buffer = 2M # ./mysqltuner.pl >> MySQLTuner 1.2.0 - Major Hayden <[email protected]> >> Bug reports, feature requests, and downloads at http://mysqltuner.com/ >> Run with '--help' for additional options and output filtering -------- General Statistics -------------------------------------------------- [--] Skipped version check for MySQLTuner script [OK] Currently running supported MySQL version 5.1.52-log [OK] Operating on 64-bit architecture -------- Storage Engine Statistics ------------------------------------------- [--] Status: +Archive -BDB +Federated +InnoDB -ISAM -NDBCluster [--] Data in MyISAM tables: 2G (Tables: 26) [--] Data in InnoDB tables: 749M (Tables: 250) [!!] Total fragmented tables: 262 -------- Security Recommendations ------------------------------------------- -------- Performance Metrics ------------------------------------------------- [--] Up for: 31d 2h 30m 38s (680M q [253.371 qps], 2M conn, TX: 4825B, RX: 236B) [--] Reads / Writes: 89% / 11% [--] Total buffers: 20.6G global + 15.1M per thread (1000 max threads) [OK] Maximum possible memory usage: 35.4G (51% of installed RAM) [OK] Slow queries: 0% (35K/680M) [OK] Highest usage of available connections: 53% (537/1000) [OK] Key buffer size / total MyISAM indexes: 512.0M/457.2M [OK] Key buffer hit rate: 100.0% (9B cached / 264K reads) [OK] Query cache efficiency: 42.3% (260M cached / 615M selects) [!!] Query cache prunes per day: 4384652 [OK] Sorts requiring temporary tables: 0% (1K temp sorts / 38M sorts) [!!] Joins performed without indexes: 100404 [OK] Temporary tables created on disk: 17% (7M on disk / 45M total) [OK] Thread cache hit rate: 99% (537 created / 2M connections) [!!] Table cache hit rate: 0% (1K open / 946K opened) [OK] Open file limit used: 9% (453/5K) [OK] Table locks acquired immediately: 99% (758M immediate / 758M locks) [OK] InnoDB data size / buffer pool: 749.3M/20.0G -------- Recommendations ----------------------------------------------------- General recommendations: Run OPTIMIZE TABLE to defragment tables for better performance Enable the slow query log to troubleshoot bad queries Adjust your join queries to always utilize indexes Increase table_cache gradually to avoid file descriptor limits Variables to adjust: query_cache_size (> 64M) join_buffer_size (> 1.0M, or always use indexes with joins) table_cache (> 1024)

  Read the article

• How to find source of 301/302 redirect loop? Heroku GoDaddy Zerigo

  - by user179288

  this should be a relatively simple problem but I'm having trouble.I hope this is the right forum to post on as I've seen people get booted off stack-overflow for this sort of thing. I've setup a web app on heroku (cedar stack) at my-web-app.herokuapp.com and I'm trying to direct my-domain.com and www.my-domain.com to it. As per instructions on the heroku documentation, I've set my-domain.com to redirect (forwarding) to www.my-domain.com and then set a C-Name from www.my-domain.com to my-web-app.herokuapp.com. But the C-Name doesn't seem to be working right and is sending back to my-domain.com, causing a loop and I can't work out why. I first configured these setting at GoDaddy.com where I registered the domain but then tried to avoid the problem by using Heroku's Zerigo DNS add-on, setting the nameservers on GoDaddy to the ones given for Zerigo. However the problem remains. Here is the output from dig for my-domain.com ("drop-circles.com"): ; <<>> DiG 9.3.2 <<>> any drop-circles.com ;; global options: printcmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 671 ;; flags: qr rd ra; QUERY: 1, ANSWER: 8, AUTHORITY: 0, ADDITIONAL: 5 ;; QUESTION SECTION: ;drop-circles.com. IN ANY ;; ANSWER SECTION: drop-circles.com. 433 IN NS b.ns.zerigo.net. drop-circles.com. 433 IN NS d.ns.zerigo.net. drop-circles.com. 433 IN NS e.ns.zerigo.net. drop-circles.com. 433 IN NS a.ns.zerigo.net. drop-circles.com. 433 IN NS c.ns.zerigo.net. drop-circles.com. 433 IN SOA a.ns.zerigo.net. hostmaster.zerigo.com. 1372250760 10800 3600 604800 900 drop-circles.com. 433 IN A 64.27.57.29 drop-circles.com. 433 IN A 64.27.57.24 ;; ADDITIONAL SECTION: d.ns.zerigo.net. 68935 IN A 174.36.24.250 e.ns.zerigo.net. 69015 IN A 72.26.219.150 a.ns.zerigo.net. 72602 IN A 64.27.57.11 c.ns.zerigo.net. 69204 IN A 109.74.192.232 b.ns.zerigo.net. 70549 IN A 174.37.229.229 ;; Query time: 15 msec ;; SERVER: 194.168.4.100#53(194.168.4.100) ;; WHEN: Wed Jun 26 14:29:07 2013 ;; MSG SIZE rcvd: 293 Here is the output from dig for www.my-domain.com ("www.drop-circles.com"): ; <<>> DiG 9.3.2 <<>> any www.drop-circles.com ;; global options: printcmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 1608 ;; flags: qr rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;www.drop-circles.com. IN ANY ;; ANSWER SECTION: www.drop-circles.com. 407 IN CNAME drop-circles-website.herokuapp.com. ;; Query time: 19 msec ;; SERVER: 194.168.4.100#53(194.168.4.100) ;; WHEN: Wed Jun 26 14:29:15 2013 ;; MSG SIZE rcvd: 83 And from Fiddler if I use the inspector when I try either address I get a series of requests, with the my-domain.com ("drop-circles.com") looking like this: Request: GET http://drop-circles.com/ HTTP/1.1 Accept: text/html, application/xhtml+xml, */* Accept-Language: en-gb User-Agent: Opera/9.80 (Windows NT 5.1; U; Edition IBIS; Trident/5.0) Accept-Encoding: gzip, deflate Connection: Keep-Alive Host: drop-circles.com Response: HTTP/1.1 302 Found Server: nginx/0.8.54 Date: Wed, 26 Jun 2013 13:26:55 GMT Content-Type: text/html;charset=utf-8 Connection: keep-alive Status: 302 Found Location: http://www.drop-circles.com/ Content-Length: 113 <html><body>Redirecting to <a href="http://www.drop-circles.com/">http://www.drop-circles.com/</a></body></html> And the www.my-domain.com ("www.drop-circles.com") looking like this: Request: GET http://www.drop-circles.com/ HTTP/1.1 Accept: text/html, application/xhtml+xml, */* Accept-Language: en-gb User-Agent: Opera/9.80 (Windows NT 5.1; U; Edition IBIS; Trident/5.0) Accept-Encoding: gzip, deflate Connection: Keep-Alive Host: www.drop-circles.com Response: HTTP/1.1 301 Moved Permanently Content-Type: text/html Date: Wed, 26 Jun 2013 13:26:56 GMT Location: http://drop-circles.com/ Vary: Accept X-Powered-By: Express Content-Length: 104 Connection: keep-alive <p>Moved Permanently. Redirecting to <a href="http://drop-circles.com/">http://drop-circles.com/</a></p> Any and all help would be greatly appreciated. If it is not at all obvious from these readouts what it might be could someone at least tell me which company GoDaddy, Zerigo or Heroku should I go to for support since I don't really know enough to be able to say where the problem lies. Thank you.

  Read the article

• Creating IIS Rewrite Rules

  - by Tom Bell

  I'm having a hard time converting old .htaccess rewrite rules to new IIS ones so I was wondering if anyone could point me in the right direction. Below are some example URLs I would like rewriting. http://example.org.uk/about/ Rewrites to http://example.org.uk/about/about.html ----------- http://example.org.uk/blog/events/ Rewrites to http://example.org.uk/blog/events.html ----------- http://example.org.uk/blog/2010/11/foo-bar Rewrites to http://example.org.uk/blog/2010/11/foo-bar.html The directories and file names are generic and could be anything. Any help would be greatly appreciated.

  Read the article

• show php error message on IIS 7

  - by Max

  I am using IIS as a webserver on my development machine for PHP webdevelopment. Or at least, I am trying to. When there is a syntax error in a PHP script and I open that file in my webbrowser, I just get an 503 "internal server error" and the default IIS error page for this error. Some browsers dont open that file at all, possibly because of the 503 HTTP Response Header. I would like IIS to act in that case just like the apache webserver: display the PHP file with the error anyway, so that the error message gets printed out. How can this be done? EDIT: PHP settings: display_errors is on and error_reporting is set to E_ALL

  Read the article

• Three apps going through apache. How to configure apache httpd?

  - by Chris F.

  I have a quick question but I've been struggling to find the best solution: I have two java webapps and wordpress (php) that I need to serve through my Prod website: App #1 should be accessed when pointing to www.example.com/ (this would have other url too such as "www.example.com/book") App #2 should be accessed when pointing to www.example.com/manage Finally WordPress would be accessed at www.example.com/info How can I configure apache to serve all these three instances at the same time? So far I have and it's not quite working right. Any suggestions would be much appreciated! Listen 8081 <VirtualHost *:8081> DocumentRoot /var/www/html </VirtualHost> ProxyPass /manage http://127.0.0.1:8080/manage ProxyPassReverse /manage http://127.0.0.1:8080/manage ProxyPass /info http://127.0.0.1:8081/info ProxyPassReverse /info http://127.0.0.1:8081/info ProxyPass / http://127.0.0.1:9000/ ProxyPassReverse / http://127.0.0.1:9000/

  Read the article

• Restrict SMB user from changing password

  - by Canadian Luke

  On a server running Debian Wheezy and Samba ver 3 with a tdb backend, how do I restrict a single user from changing the password? This account is one of 2 generic accounts, one for students and one for Teachers on Call (TOC). The users are created, but I'm not deploying the server yet. When looking through Google, I came across setting the maximum password age, but not setting the minumum password age (I'd be happy with a 5 year password...)

  Read the article

• mod_rewrite filename from mod_pagespeed back to normal files

  - by British Sea Turtle

  I am hoping someone can help me with this problem. I am moving to a new server and not using mod_pagespeed any more. However we have lots of external links to images on our site using the strange mod_pagespeed filenames. This is not an issue but we do not want to have lots of 404 errors. So I have lots of links like the following : http://www.domain.com/images/150x150xlink.png.pagespeed.ic.pPXw45HSQm.png http://www.domain.com/images/paris_01.gif.pagespeed.ce.vfrkuKUaj0.gif http://www.doamin.com/images/1st2.gif.pagespeed.ce.OUg38q6VbZ.gif How can I redirect them to : http://www.domain.com/images/150x150xlink.png http://www.domain.com/images/paris_01.gif http://www.doamin.com/images/1st2.gif There are thousands of files like this so I am hoping for a simple solution with mod_rewrite, I tried this but it does not work. So any help would be appreciated. RewriteCond %{REQUEST_URI} \.gif\.pagespeed\. [NC] RewriteRule ^(.*?\.gif)\..*\.gif$ $1 [NC,L]

  Read the article

• How to set up Apache 2 to serve only subdirectories

  - by Lynden Shields

  I have 3 sites which need to be hosted on a web server (apache2 from repo running on Ubuntu 12.04). They are each in their own subdirectory within /var/www/ I would like apache to serve files from the relevant directories only if the directory name is given in the URL, but not serve the /var/www/ directory itself. E.g: http://1.2.3.4/site1/ should work and serve the index from /var/www/site1/index.html, but http://1.2.3.4/ should not serve anything. Currently, I can't get the url to point to the directory. Either I can get http://1.2.3.4/ to serve everything within /var/www/ (including /var/www/site2/secretstuff/), or I can get the root http://1.2.3.4/ to serve one of the subdirectories (/var/www/site1/). This is unacceptable site 1 needs Indexes enabled but the others must not. I just want to make site1's config only respond to requests of the form http://1.2.3.4/site1/* and not handle requests of the form http://1.2.3.4/ I do not have a domain name set up so I can't use subdomains.

  Read the article

• Misbehavior in regular expression in VIM

  - by poissonbreaker

  I am having a problem with a regular expression on vim. I have a pattern as follows: http:\/\/\(\w\+\.\?\)\+ [matches http://(AS MANY WORDS FOLLOWED BY DOT OR NOT ENCOUNTERS) e.g. http://wd1.wd2.com] I have a text as follows: http://wd1.wd2.com/wd3 I am trying to make this substitution on it: s/\(http:\/\/\)\(\w\+\.\?\)\+/\1wd4.wd5.com and the result is http://wd4.wd5.com /wd3 (Notice the white space inserted at the end of the replacement) How can I avoid having this inserted space? I am afraid is a bug in the regexp engine but I am not sure.

  Read the article

• Can I proxy my no-ip domain using a .htaccess file on my hosted domain?

  - by Dean

  I have a domain http://www.example.com which has a hosting package and website on it. I also have a http://example.no-ip.org domain which contains some content I would like to appear under the same domain. Can I setup a .htaccess file at http://www.example.com/proxy/ which proxies the files at http://www.example.no-ip.org/files/ Similarly, could I host an entire domain in the same way?, e.g. http://www.example2.com/ proxying http://example.no-ip.org/files2/ Alternatively, if someone were to say "That's stupid, use this free (or super-cheap) dynamic DNS host:" I would probably accept that answer.

  Read the article

• CURL -I issue stop responding when contain "="

  - by user1512778

  i did this command : curl -I 'http://criminaljustice.state.ny.us/cgi/internet/nsor/fortecgi?serviceName=WebNSOR&templateName=detail.htm&requestingHandler=WebNSORDetailHandler&ID=368343543' but stuck but if i did this : curl -I 'http://criminaljustice.state.ny.us/cgi/internet/nsor/fortecgi' HTTP/1.1 200 OK Content-length: 207 Content-type: text/html Server: Sun-ONE-Web-Server/6.1 Date: Sat, 15 Dec 2012 08:49:14 GMT Via: 1.1 proxy-internet-revproxy Proxy-agent: Oracle-iPlanet-Proxy-Server/4.0 then i try shorten it : curl -I 'http://criminaljustice.state.ny.us/cgi/internet/nsor/fortecgi?serviceName=WebNSOR&templateName=detail.htm' stuck too i dont know why seems like if the url contain "=" it stop responding so tried this url removing the "=" (serviceName=WebNSOR to serviceNameWebNSOR) : curl -I 'http://criminaljustice.state.ny.us/cgi/internet/nsor/fortecgi?serviceNameWebNSOR' HTTP/1.1 200 OK Content-length: 207 Content-type: text/html Server: Sun-ONE-Web-Server/6.1 Date: Sat, 15 Dec 2012 08:50:38 GMT Via: 1.1 proxy-internet-revproxy Proxy-agent: Oracle-iPlanet-Proxy-Server/4.0 why i cant use = ? please assist me

  Read the article

• Apply rewrite rule for all but all the files (recursive) in a subdirectory?

  - by user784637

  I have an .htaccess file in the root of the website that looks like this RewriteRule ^some-blog-post-title/ http://website/read/flowers/a-new-title-for-this-post/ [R=301,L] RewriteRule ^some-blog-post-title2/ http://website/read/flowers/a-new-title-for-this-post2/ [R=301,L] <IfModule mod_rewrite.c> RewriteEngine On ## Redirects for all pages except for files in wp-content to website/read RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteCond %{REQUEST_URI} !/wp-content RewriteRule ^(.*)$ http://website/read/$1 [L,QSA] #RewriteRule ^http://website/read [R=301,L] RewriteBase / RewriteRule ^index\.php$ - [L] RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule . /index.php [L] </IfModule> My intent is to redirect people to the new blog post location if they propose one of those special blog posts. If that's not the case then they should be redirected to http://website.com/read. Nothing from http://website.com/wp-content/* should be redirected. So far conditions 1 and 3 are being met. How can I meet condition 2?

  Read the article

< Previous Page | 216 217 218 219 220 221 222 223 224 225 226 227  | Next Page >