Search Results

Search found 25718 results on 1029 pages for 'external hard drive'.

Page 226/1029 | < Previous Page | 222 223 224 225 226 227 228 229 230 231 232 233  | Next Page >

• Proliant RAID 1 Rebuild Questions

  - by Nicholas

  I have a HP Proliant ML350 G5 server that experienced a power supply failure overnight. The power supply was replaced but unfortunately it got restarted with only 1 disk in the RAID 1 set plugged in. (The raid controller is the build in E200i). The raid BIOS then said on start-up that it had entered Interim Recovery Mode. However I would have expected it to still start up with only the 1 drive. The bios however says that it cannot find a C: drive and enters a reboot loop polling the other boot devices. First question is, is this normal behaviour not to start up on 1 disk? The second drive was then plugged in (all drives are ok) and the raid bios started an automatic rebuild on that disk. This appears to be a background process as there is no progress shown. However based on the light flashing it looks like it is working. My second question is how long will this rebuild take? (36GB 15K SAS drive). I cannot see any error messages and it looks like it is rebuilding the drive ok, but the computer still will not start-up. It still says during the boot up process that the C: drive is not found. If I wait for the rebuild to finish, is it likely to fix itself and find the C: drive? Or is there some other problem here?

  Read the article

• Why does my dd backup of MacBook OS X fail to boot upon restore?

  - by James

  I created a backup of a MacBook hard drive (WD2500BEVS-88US) by hooking it up as a secondary drive on my linux system (Ubuntu 10.10). I used the following command: sudo dd if=/dev/sdc of=/home/backup.img bs=2M This appears to have completed with no errors. I noticed that the file is only 68 GB in size even though the drive is 250 GB in capacity. I restored the image to a spare drive (WD2500BEVS) with the following command: sudo dd if=/home/backup.img of=/dev/sdb bs=2M When I boot the spare drive in the Mac, it appears to start up for a few seconds and then shuts down. (It does not appear to load into the OS at all). When I open up the drive that won't boot in GParted, it looks like this: When looking at the information for the middle partition with the little red exclamation mark, it shows this: The original hard drive that boots ok shows up like this: Further info on both drives: sudo fdisk -l Disk /dev/sdb: 250.1 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdb1 1 30402 244198580 ee GPT WARNING: GPT (GUID Partition Table) detected on '/dev/sdc'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sdc: 250.1 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdc1 1 30402 244198580 ee GPT So why is my backup or restore failing? Why is dd not creating a byte for byte duplicate?

  Read the article

• Backup, Migrate or Clone Failing CentOS 4 (LVM)

  - by Hegelworm

  Hello there, I've been running a BlueQuartz CentOS 4 system (Nuonce.net distro) for a few years now and although the hard drive (Deskstar) has always been a bit noisy, on a few recent occasions I've heard it having trouble spinning up. Basically, I want to clone this drive to a similar sized one (80 Gig). I've spent many hours reading upon dd, dd_rescue, rsync, clonezilla and LVM mirroring yet the sheer number of options and nightmarish accounts has left me frozen - unable to make an informed decision as to how to start. I've made a few attempts. dd failed after about 2 hours, as, although the drives appeared to be identical on the surface (ATA Seagate Barracudas, Thai not Chinese), the destination drive is slightly smaller. My most recent attempt involved using a Debian CD to format the new drive and then rsync-ing everything over and editing the new drive's grub and fstab to reflect the changes. No joy here either as I hadn't chosen LVM when partitioning the destination drive and it wouldn't boot. As you can probably tell, I'm out of my depth here and a panic-invoking mixture of caution and frustration has prompted me to sign up here. The server itself, although not strictly a production environment, has a very specific installation of Festival, LAME and ffMpeg and provides the back-end for a Text-to-Speech jQuery plugin that I've built over the last 2 years. I'm also planning to rebuild the whole TTS system on Debian as the existing CentOS system still has PHP4 etc. For now though, I'd really like to just shift everything over to a new drive. As this is my first post, please feel free to lay any house rules on me that I might've overlooked; I've been hovering around StackOverflow for a while now but have only just signed up. Many thanks.

  Read the article

• Windows won't sleep after booting from grub

  - by mkasberg

  I recently added a second hard drive to my computer and I am using it do dual-boot Linux (Ubuntu 12.04) with Windows 7. Both hard drives are SATA. I am using the default grub bootloader on my second hard drive. The windows drive is unmodified. To get to grub, I changed the hard disk boot priority in my BIOS (P35-DS3L) to boot from the second drive. The problem I'm having is that when I boot to Windows 7 (on sda) from grub (on sdb), Windows 7 will not go to sleep (from the start menu). The display shuts off momentarily as if its going to sleep, then comes back on and displays the switch-user screen. Powercfg -lastwake does not show anything. I am sure that this is related to booting from grub on sdb because when I change the hard disk boot priority in the BIOS to boot from my (unmodified) Windows hard disk, the computer goes to sleep fine. It occurred to me that installing grub on sda might solve the problem, but I'd rather not since I like to have my windows hard disk unmodified so that booting to it from the BIOS boots directly to windows. A possible work around is to use the BIOS as a bootloader, by pressing F8 to select the boot device. Still, I'd like to know why the problem is happening in the first place.

  Read the article

• Why are folders disappearing in Windows XP?

  - by XenoFoxx

  I am researching a problem for a friend, and unfortunatly do not have direct access to his computer. I've tried to gather as much information as possible and I have researched it on various websites. I've not found anyone having the same problem my friend is having. So here goes: He has a media server in his home running Microsoft Windows XP. It has 3 drives, 1 for the OS and 2 for mass storage. Not long ago he went to access one of the mass storage media drives and it was empty, except for a single folder. His first assumption was that his roommate had deleted everything on the drive (excluding the remaining folder). He then checked the properties of the drive and it was still saying that the hard drive was nearly full. I told him to check the recycling bin, thinking that whoever deleted them didn't clear them from recycling and that they were still taking up space on the drive. My friend said the recycling bin was empty. So we have a drive that the Windows file management system says is empty (again except for the remaining folder), but the properties of the drive say it's mostly full. Now it gets weirder My friend tried to create a new folder on this drive and it auto-named itself "New Folder(1)" which means that it recognizes there is already a "New Folder" in that directory. He tried to rename it to a name that he KNEW was there previsouly, and Windows wouldn't allow it because it was a duplicate folder name. SO now it seems the folders are there, but not displaying in Windows Explorer. Both of us have no idea why this is occuring, why the folders vanished, why the one remaining folder didn't vanish, or how to make them visable again. Anyone else ever experience this? I can get more details if needed.

  Read the article

• how to initialize two logical drives on a HP P400i controller without reboot

  - by John

  What I am trying to do is initialize two logical drives on a HP P400i embedded controller without a reboot of the system here my current Array config: array A (SAS, Unused Space: 0 MB) logicaldrive 1 (17.9 GB, RAID 5, OK) logicaldrive 2 (17.9 GB, RAID 5, OK) logicaldrive 3 (75.9 GB, RAID 5, OK) logicaldrive 4 (25.0 GB, RAID 5, OK) physicaldrive 1I:1:1 (port 1I:box 1:bay 1, SAS, 72 GB, OK) physicaldrive 1I:1:2 (port 1I:box 1:bay 2, SAS, 72 GB, OK) physicaldrive 1I:1:3 (port 1I:box 1:bay 3, SAS, 72 GB, OK) array B (SAS, Unused Space: 0 MB) logicaldrive 5 (99 MB, RAID 0, OK) logicaldrive 6 (68.2 GB, RAID 0, OK) physicaldrive 1I:1:4 (port 1I:box 1:bay 4, SAS, 72 GB, OK) windows 2003 machine running the HpCISs2.sys driver version 6.20.0.32 . I have the ACU and ACU CLI tools installed version 8.28.13.0, P400i firmware version 2.74 . Now what I'd like to do is removes the physical drive 1I:1:4 and delete the two logical drives in array B. then insert a new drive in to bay 4 that contains two new logical drives and have them show up in array B again. So far after I remove the drive and delete the failed logical drives, I insert the new drive and run HPacucli rescan. I get the new drive to show up as unassinged physical drive but I cant figure out now to "for lack of a better word" mount the 2 logical drives on the new unassinged disk. If I reboot the system the array controller picks up the new fourth drive and creates Array B with the drives without problem but I'd really like to not have to reboot the server. Any ideas?

  Read the article

• Unable to write DVD-R(Blank DVD's)

  - by FrozenKing

  I have a problem in dvd drive i.e. It can read CD/DVD and can write CD and all CD/DVD-RW but cannot write DVD DVD drive model is SH-S203B Samsung; I also have a log file created by nero burning rom 11. Actually the fact is no Blank DVD's are being read in my dvd drive only previously written dvd's can be read! Is this the problem of OS or should I try cleaning the dvd drive or my DVD drive is 4yrs old so is it going to spoil now, since it is showing this type of symptoms! OS = WinXP AV = KIS 2012 DVD Drive = Samsung SH-S203B (Also tried latest firmware and downgrade versions also) IA32 Nero Version: 11.2.4.100 Internal Version: 11,2,4,100 Recorder: <TSSTcorp CDDVDW SH-S203B>Version: SB04 - HA 1 TA 0 - 11.2.4.100 Adapter driver: <Serial ATA> HA 1 Drive buffer : 2048kB Bus Type : via Inquiry data CD-ROM: <TSSTcorp CDDVDW SH-S203B >Version: SB04 - HA 1 TA 0 - 11.2.4.100 Adapter driver: <Serial ATA> HA 1 18:58:10 #37 SPTI -1511 File SCSIPassThrough.cpp, Line 224 CdRom0: SCSIStatus(x02) WinError(0) NeroError(-1511) CDB Data: 0x28 00 00 00 00 00 00 00 10 00 Sense Key: 0x04 (KEY_HARDWARE_ERROR) Sense Code: 0x3E Sense Qual: 0x02 Sense Area: 0x70 00 04 00 00 00 00 0A 00 00 00 00 3E 02 Buffer x08047340: Len x8000 18:58:10 #38 SectorVerify 20 File Cdrdrv.cpp, Line 12057 Read errors from sector 0 to 14 <Padding> 18:58:19 #39 SPTI -1511 File SCSIPassThrough.cpp, Line 224 CdRom0: SCSIStatus(x02) WinError(0) NeroError(-1511) CDB Data: 0x28 00 00 00 00 10 00 00 10 00 Sense Key: 0x04 (KEY_HARDWARE_ERROR) Sense Code: 0x3E Sense Qual: 0x02 Sense Area: 0x70 00 04 00 00 00 00 0A 00 00 00 00 3E 02 Buffer x08047340: Len x8000 18:58:19 #40 SectorVerify 21 File Cdrdrv.cpp, Line 12057 Read error at sector 15 <Virtual Multisession Info> 18:58:19 #41 SectorVerify 20 File Cdrdrv.cpp, Line 12057 Read errors from sector 16 to 18 <Volume Structure Descriptor Sequence> 18:58:28 #42 SPTI -1511 File SCSIPassThrough.cpp, Line 224 CdRom0: SCSIStatus(x02) WinError(0) NeroError(-1511) CDB Data: 0x28 00 00 00 00 20 00 00 10 00 Sense Key: 0x04 (KEY_HARDWARE_ERROR) Sense Code: 0x3E Sense Qual: 0x02 Sense Area: 0x70 00 04 00 00 00 00 0A 00 00 00 00 3E 02 Buffer x08047340: Len x8000

  Read the article

• LVM and cloning HDs

  - by jcea

  Using Linux, I have several backup levels. One of them is a periodical sector by sector copy (using dd) of my laptop harddisk to an external USB disk. Yes, I have other backups too, like remote rsync. This approach (the disk dd) is OK when cloning a HDD with no LVM volumes, since I can plug the external disk anytime and mount the partitions simply mounting /dev/sdb* instead of /dev/sda*. Trivial and handy. Today I moved ALL my harddisk (including the /boot) to LVM. Everything works fine. I will stress it for a couple of days, and then I will do a sector by sector copy to my external harddisk. Now I have a problem, I guess. If in the future I plug the external USB HDD to recover any file, the OS will detect a duplicate LVM configuration, with the same name and the same UUID. Even doing a vgrename (which LVM would be renamed, the internal HDD or the external HDD?), the cloned UUID will not change. Is there any command to change name and UUID? Ideally I would clone the HDD and then change the LVM group name and its UUID, but I don't know how to do it. Another related issue would be... In the past I have booted my laptop using the external disk, using the BIOS boot menu and changing GRUB entries manually to boot from /dev/sdb instead of /dev/sda. But now my current GRUB configuration boots directly from a LVM logical volume, something like: set root='(LVM-root)' in my grub.cfg. So... What is going to happen with duplicated volumes? Any suggestion? I guess I could repartition my external harddisk and change backup strategy from dd to rsync, but this disk has windows installed too, and I really would like to have a physical "real" copy.

  Read the article

• Recover data from a Thecus N4100 NAS jbod partition

  - by TimothyP

  I have a Thecus N4100 NAS wich had a 2TB drive in it configured as jbod partition. Later I tried adding a second drive to expand the available space. I added it to the jbod configuration but I did not get any extra space. Then I tried removing the second drive but then the NAS system indicated the jbod configuration was damaged. After a reboot it told me there is no configuration and I need to create a new RAID/jbod configuration and that I would lose all data on the drive. Of course I did not do this, I took the 2TB drive and checked with Linux if the partition was still there and it is... completely intact. I found that linux recognizes it as a /dev/mdX device and that I should be able to mount it but I don't know the file system type. Anyway.... is there a way to recover the data? Since everything has always been on a single drive it should all be there right? I can connect the drive to Windows , Linux or MacOS so whatever gets the job done.

  Read the article

• WS2008 subst in Logon script does not "stick"

  - by Frans

  I have a terminal server environment exclusively with Windows Server 2008. My problem is that I need to "map" a drive letter to each users Temp folder. This is due to a legacy app that requries a separate Temp folder for each user but which does not understand %temp%. So, just add "subst t: %temp%" to the logon script, right? The problem is that, even though the command runs, the subst doesn't "stick" and the user doesn't get a T: drive. Here is what I have tried; The simplest version: 'Mapping a temp drive Set WinShell = WScript.CreateObject("WScript.Shell") WinShell.Run "subst T: %temp%", 2, True That didn't work, so tried this for more debug information: 'Mapping a temp drive Set WinShell = WScript.CreateObject("WScript.Shell") Set procEnv = WinShell.Environment("Process") wscript.echo(procEnv("TEMP")) tempDir = procEnv("TEMP") WinShell.Run "subst T: " & tempDir, 3, True This shows me the correct temp path when the user logs in - but still no T: Drive. Decided to resort to brute force and put this in my login script: 'Mapping a temp drive Set WinShell = WScript.CreateObject("WScript.Shell") WinShell.Run "\\domain\sysvol\esl.hosted\scripts\tempdir.cmd", 3, True where \domain\sysvol\esl.hosted\scripts\tempdir.cmd has this content: echo on subst t: %temp% pause When I log in with the above then the command window opens up and I can see the subst command being executed correctly, with the correct path. But still no T: drive. I have tried running all of the above scripts outside of a login script and they always work perfectly - this problem only occurs when doing it from inside a login script. I found a passing reference on an MSFN forum about a similar problem when the user is already logged on to another machine - but I have this problem even without being logged on to another machine. Any suggestion on how to overcome this will be much appreciated.

  Read the article

• How to access previous VHD versions of system backup?

  - by feklee

  Quote from the 31 Oct 2009 TechNet article "Learn more about system image backup": During the first backup, the backup engine scans the source drive and copies only blocks that contain data into a .vhd file stored on the target, creating a compact view of the source drive. The next time a system image is created, only new and changed data is written to the .vhd file, and old data on the same block is moved out of the VHD and into the shadow copy storage area. Volume Shadow Copy Service is used to compute the changed data between backups, as well as to handle the process of moving the old data out to the shadow copy area on the target. This approach makes the backup fast (since only changed blocks are backed up) and efficient (since data is stored in a compact manner). When restoring the image, blocks will be restored to their original locations on the source disk. If you want to restore from an older backup, the engine reads from the shadow copy area and restores the appropriate blocks. For the last days, a daily system backup of drive C: to drive E: has been scheduled and run by Windows 7 Backup and Restore. Drive C: currently holds 233 GB of data, which fits comfortably on drive E:, a 1 TB drive, with 727 GB of free space remaining. How do I access the previous version of a VHD? I right clicked on files and folders in E:\WindowsImageBackup, and I looked for Previous Versions but always: There are no previous versions available

  Read the article

• How to migrate Outlook Express mail rules?

  - by ronwest

  I have a home computer that only had a 15Gb C: drive, and ran out of space with all the Microsoft Updates, etc, that keep coming down. So I fitted a 160Gb drive as a C: drive and altered the drive jumpers to make the old C: drive into a slave D: drive, to save migrating documents, etc. I've installed a clean copy of Windows XP SP3 and reassigned the new Outlook Express' mailstore path to point to the old mailstore folder that now has a D: drive letter - and it all works OK. However, my extensive list of mail rules have not been transferred to the new OE and I have not been able to identify how they are stored. To find it I added a new rule to the new OE, exited OE, then searched on the whole computer (including hidden/system files) for files altered around the time I added the rule. I hoped I could just overwrite a new empty file with an old one. But the only files that seem to be changed are Windows system-level files and some bits and pieces in the Windows\PreFetch sub-folder. None of them can be opened as XP has them locked, and none of them have names that are anything to do with email or rules. Does anyone know of any way of migrating OE rules, or do I have to re-enter them by hand? Thanks!

  Read the article

• Windows XP Disappearing Folders

  - by XenoFoxx

  I am researching a problem for a friend, and unfortunatly do not have direct access to his computer. I've tried to gather as much information as possible and I have researched it on various websites. I've not found anyone having the same problem my friend is having. So here goes: He has a media server in his home running Microsoft Windows XP. It has 3 drives, 1 for the OS and 2 for mass storage. Not long ago he went to access one of the mass storage media drives and it was empty, except for a single folder. His first assumption was that his roommate had deleted everything on the drive (excluding the remaining folder). He then checked the properties of the drive and it was still saying that the hard drive was nearly full. I told him to check the recycling bin, thinking that whoever deleted them didn't clear them from recycling and that they were still taking up space on the drive. My friend said the recycling bin was empty. So we have a drive that the windows file management system says is empty (again except for the remaining folder), but the properties of the drive say it's mostly full. Now it gets weirder My friend tried to create a new folder on this drive and it auto-named itself "New Folder(1)" which means that it recognizes there is already a "New Folder" in that directory. He tried to rename it to a name that he KNEW was there previsouly, and windows wouldn't allow it because it was a duplicate folder name. SO now it seems the folders are there, but not displaying in Windows Explorer. Both of us have no idea why this is occuring, why the folders vanished, why the one remaining folder didn't vanish, or how to make them visable again. Anyone else ever experience this? I can get more details if needed.

  Read the article

• HD working with IDE USB adapter but not recognised by bios

  - by Rajeeva

  I have a Windows XP Pentium III desktop with two hard drives. The first one has the OS and is luckily working. The second drive on the secondary master IDE channel few days back was unable to read some files and since then for some time it was failing and reviving intermittently and now it is always showing as failed on the IDE channel When the HD was intermittenly failing, I was able to copy some data from it to the other drive - also during that time if the system was running and the hard disk failed at that time, the system froze and then i had to reboot. then I got a new 80 gb hdd similar (same make - seagate barracuda) to the earlier failing one, a new data cable for the drive and an IDE to USB adapter. the new hard drive i installed in the previous drive's place (secondary master), formatted it and it worked for 1 day and then it also failed - simultaneously i connected the old hd to the IDE/USB adapter and i could view all the data - some of that data i was able to back up from the old hd to the new hd before the new hd failed the new hd i have tried connecting on the primary channel as the slave disk but when i do that then the bios does not detect either the OS drive or the new drive and the system does not boot surprisingly, the older (previously failed) hd and the new hd are both working fine on the usb channel with the IDE/USB adapter. i have ruled out any problem with the secondary channel since the dvd rom i was earlier using as primary slave have now connected to secondary master and it works fine. i am really confused by this behavior on my system. please can anybody try to solve this for me. thanks.

  Read the article

• Un-do Windows disk convert HFS+

  - by BLAKE

  Last night, a friend asked my to give him a copy of a word document. He handed me an external hard drive and left. I plugged the hard drive into my file server running Windows Server 2003, opened disk management and clicked OK. (I know that in Windows 2003 you need to manually assign a drive letter to external drives.) I then looked at the drive in disk management and it said that it was unallocated space. I called my friend and he said that there was data on the drive, but he used it with his Mac Book. Aperantly when I clicked OK in disk management I converted the from HFS+ file system to something else. Is there any way to undo the disk convert? I immediately removed the drive, so there was no writing to it. Windows did not format the drive, it just converted it. Is the data still there? All the data recovery programs I have are for windows, can they read the Mac file system? I need to get the data back, what can I do?

  Read the article

• Computer will not boot - disk read error - cannot boot from HD or DVD

  - by Grant Palin

  This is a 3 year-old system: HP a1640n. There have been no issues with it in the past. I added a video card 2 years ago, and more memory 1 year ago, both without issues. There haven't been any recent hardware changes. I did install Win7 in Oct., but there were no issues with that either. I used the computer fine two nights ago, and turned it off. Yesterday, I tried to turn it on, and got the error: "A Disk Read Error Occurred. Press CTRL ALT DEL to restart" So I restart, see the initial start screen (HP) and enter the BIOS. The hard drive and dvd drive appear to be listed, but the names are gibberish text. I tried putting a Windows disk in the dvd drive, and continued with the boot, but the disk did not get recognized. Even though the BIOS was set to check for optical media before the hard drive. Back to the error screen. If the computer would boot from a cd or dvd, I would just figure the hard drive needed replacing. But both being problematic worries me. Is this a matter of replacing both the hard drive and dvd drive, or might it be an indication of a bigger problem? Thanks for any advice.

  Read the article

• Can a non-redundant RAID5 cause any serious problems (compared to RAID0)?

  - by leemes

  I used to have a three-disc RAID5 (mdadm) in my computer for personal media storage (music, videos, photos, programs, games, ...). It had three discs with 750 GB each, resulting in an array capacity of 1.5 TB. One day (one year ago), I needed one of those discs to install another operating system. I thought, I don't need the redundancy anymore since I backup the most important stuff (personal photos e.g.) on an external disc anyway. So I decided to remove one of the three discs without converting the RAID to RAID0 or even two separate discs, because I had no temporary storage (since one cannot simply convert the RAID5 to RAID0 AFAIK). So now, for about one year, I have a non-redundant RAID5 with 2 of 3 discs running. Sometimes, one of the discs has a defective contact at the power cable or something similar causing the drive to stop working temporarily (I don't know exactly what it is). Since it still works when rebooting the computer and in most cases by calling some mdadm commands, it wasn't that problematic. Note that the data is not very critical, since I still have a backup of the most important stuff. But in the last few weeks, one of the drives fails very frequently (every few hours), so it gets really annoying to manage this. My questions are: Is there any disadvantage (apart from the annoying management) of a non-redundant RAID5 (with one drive less than typical) over a RAID0? If I understand it correctly, both have no redundancy and the same capacity. On a temporary drive failure, I can restart the array in both cases, assuming that the drive itself still works after the failure. Can it happen that the drive contents alter on a drive failure, making the array inconsistent? If so, can I tell mdadm to check the array for failures (without a file system level checking tool)? Since the drive most probably only has a defective contact causing it to fail for a second only, can I tell mdadm to automatically restart the array, so I will not even notice the failure if no application wanted to access the file system during the failure?

  Read the article

• Un-do Windows disk convert HFS+

  - by BLAKE

  Last night, a friend asked my to give him a copy of a word document. He handed me an external hard drive and left. I plugged the hard drive into my file server running Windows Server 2003, opened disk management and clicked OK. (I know that in Windows 2003 you need to manually assign a drive letter to external drives.) I then looked at the drive in disk management and it said that it was unallocated space. I called my friend and he said that there was data on the drive, but he used it with his Mac Book. Aperantly when I clicked OK in disk management I converted the from HFS+ file system to something else. Is there any way to undo the disk convert? I immediately removed the drive, so there was no writing to it. Windows did not format the drive, it just converted it. Is the data still there? All the data recovery programs I have are for windows, can they read the Mac file system? I need to get the data back, what can I do?

  Read the article

• FLTK Images (Using Cmake)

  - by Cenoc

  I'm trying to load and manipulate a jpeg file using FLTK compiled using cmake... but I get the following errors: 2LINK : warning LNK4098: defaultlib 'MSVCRT' conflicts with use of other libs; use /NODEFAULTLIB:library 2fltkimages.lib(Fl_JPEG_Image.obj) : error LNK2019: unresolved external symbol _jpeg_read_scanlines referenced in function "public: __thiscall Fl_JPEG_Image::Fl_JPEG_Image(char const *)" (??0Fl_JPEG_Image@@QAE@PBD@Z) 2fltkimages.lib(Fl_JPEG_Image.obj) : error LNK2019: unresolved external symbol _jpeg_start_decompress referenced in function "public: __thiscall Fl_JPEG_Image::Fl_JPEG_Image(char const *)" (??0Fl_JPEG_Image@@QAE@PBD@Z) 2fltkimages.lib(Fl_JPEG_Image.obj) : error LNK2019: unresolved external symbol _jpeg_calc_output_dimensions referenced in function "public: __thiscall Fl_JPEG_Image::Fl_JPEG_Image(char const *)" (??0Fl_JPEG_Image@@QAE@PBD@Z) 2fltkimages.lib(Fl_JPEG_Image.obj) : error LNK2019: unresolved external symbol _jpeg_read_header referenced in function "public: __thiscall Fl_JPEG_Image::Fl_JPEG_Image(char const *)" (??0Fl_JPEG_Image@@QAE@PBD@Z) 2fltkimages.lib(Fl_JPEG_Image.obj) : error LNK2019: unresolved external symbol _jpeg_stdio_src referenced in function "public: __thiscall Fl_JPEG_Image::Fl_JPEG_Image(char const *)" (??0Fl_JPEG_Image@@QAE@PBD@Z) 2fltkimages.lib(Fl_JPEG_Image.obj) : error LNK2019: unresolved external symbol _jpeg_CreateDecompress referenced in function "public: __thiscall Fl_JPEG_Image::Fl_JPEG_Image(char const *)" (??0Fl_JPEG_Image@@QAE@PBD@Z) 2fltkimages.lib(Fl_JPEG_Image.obj) : error LNK2019: unresolved external symbol _jpeg_destroy_decompress referenced in function "public: __thiscall Fl_JPEG_Image::Fl_JPEG_Image(char const *)" (??0Fl_JPEG_Image@@QAE@PBD@Z) 2fltkimages.lib(Fl_JPEG_Image.obj) : error LNK2019: unresolved external symbol _jpeg_finish_decompress referenced in function "public: __thiscall Fl_JPEG_Image::Fl_JPEG_Image(char const *)" (??0Fl_JPEG_Image@@QAE@PBD@Z) I hate these linking errors..... can anyone help? Thank you in advance.

  Read the article

• How to get markers after calling drive directions in Google Maps API?

  - by Ivan Rocha

  Hi all, I just started working using Google Maps API yesterday, and trying to set up drive directions to my map. My problem is: when I call the function load, [...] gdir = new GDirections(map, directionsPanel); [...] gdir.load("from: " + fromAddress + " to: " + toAddress); it returns a map whose markers are not draggable. So, I need to make them draggable in order to recalculate the directions, but I can't get the markers objects. Someone knows how can I do it? Thanks, Ivan.

  Read the article

• How do I get a full Magento session in an external script? (Specifically, Catalog Rules)

  - by Laizer

  I'm running an external script that loads up a Magento session. Within that script, I'm loading products and grabbing a bunch of properties. The one issue is that getFinalPrice() does not apply the catalog rules that apply to the product. I'm doing everything I know to set the session, even a bunch of stuff that I think is superfluous. Nothing seems to get these rules applied. Here's a test script: require_once "app/Mage.php"; umask(0); $app = Mage::app("default"); $app->getTranslator()->init('frontend'); //Probably not needed Mage::getSingleton('core/session', array('name'=>'frontend')); $session = Mage::getSingleton("customer/session"); $session->start(); //Probably not needed $session->loginById(122); $product = Mage::getModel('catalog/product')->load(1429); echo $product->getFinalPrice(); Any insight is appreciated.

  Read the article

• how to load external xml using air application for flash programmer ?

  - by Ayman

  hi, i have faced this problem couple of days ago, while trying to import an external xml file into an AIR application. import flash.net.URLRequest; var ldr:Loader = new Loader(); var url:String = "http://willperone.net/rss.php"; var urlReq:URLRequest = new URLRequest(url); ldr.load(urlReq); ldr.addEventListener(Event.COMPLETE , function(e) { trace('Wow, completed ...'); }); ldr.contentLoaderInfo.addEventListener(IOErrorEvent.IO_ERROR, function(e) { trace('IO_ERROR'); }); and always the IO_ERROR shows up. may i do it wrong or something needs a little of configuration, so please help

  Read the article

• Can I use "Online Backup" to backup my DVS instead of pushing to an external repo?

  - by Matt Brailsford

  Hi Guys, I'm currently signed up with a third party service that hosts my mercurial repositories as a central hub to push my changes to as a sort of backup. Now, I'm looking at a system to backup my laptop and am concidering Mozy. I'm a loan developer, and work on a laptop and am usualy connected to my internet via wifi with my laptop only really being on when I'm working, so feel something like Mozy is my best option. My question is, if I'm the only developer, could I get away with just using local mercurial repos and using Mozy to backup everything up? Rather than pushing to an external repo? Many thanks Matt

  Read the article

• Sample source code for processing messages of a window created by an external program?

  - by David

  I know I have to use SetWindowLongPtr with GWLP_WNDPROC and create my own WndProc that handles the message I want (such as WM_GETMINMAXINFO and modify the MINMAXINFO structure). However, because I want to do this for a window created by another program (like notepad.exe), I can't do this from my C#/WinForms program, I have to create a native C/C++ DLL that I have to inject in the the process that created the window. Can you provide a link or the sample code to do this (the native C++ DLL and the way to call it from C# and inject it into the external process)? Thank you

  Read the article

• Eclipse hangs when rebuilding after the addition of an external JAR file.

  - by celestialorb

  I'm fairly new to Eclipse so if this is something simple I apologize, however when I attempt to add an external JAR file to my build path (specifically the "rt.jar" file which contains certain tools that I require) and then rebuild my project, Eclipse will hang at the end of the Build process. It'll get to 100% then just hang there using 100% of one of my CPU cores. At first I thought it may have been due to the relatively large size of the rt.jar file, but I tried using smaller JAR files and it still hung at 100%. Any help would be greatly appreciated! If there is something wrong with using the rt.jar file does anyone know of another JAR file that contains both tools for dealing with SOAP requests as well as XML/DOM manipulation? Thanks again!

  Read the article

< Previous Page | 222 223 224 225 226 227 228 229 230 231 232 233  | Next Page >