Search Results

Search found 23082 results on 924 pages for 'address space'.

Page 227/924 | < Previous Page | 223 224 225 226 227 228 229 230 231 232 233 234  | Next Page >

• Ubuntu 12.04 suddenly cannot connect to WPA2/WPA Personal protected connection. Windows 7 can

  - by d4ryl3

  I have a laptop with Windows 7 and Ubuntu 12.04. I have a Cisco E1200 and when I set it up, it created 2 SSIDs. Let's name them: MyConnection (WPA/WPA2 personal), and MyConnection-Guest (no authentication, guest password entered via web browser). I had no problem connecting to MyConnection before, either in Windows 7 and Ubuntu. But now, I can't access MyConnection on Ubuntu. It just says "connecting..." then disconnects after a while. But I'm able to access the internet (on Ubuntu) when I connect to MyConnection-Guest. MAC filtering is off (even if it's on its MAC address is in the white list). Any idea why I'm unable to connect to MyConnection in Ubuntu? Thanks. Update: My Ubuntu installation can connect to ANY WiFi connection (WPA/WEP/no auth), except for MyConnection. Update2: This is what "The not so easy way" returned: Initializing interface 'eth1' conf '/etc/wpa_supplicant.conf' driver 'default' ctrl_interface 'N/A' bridge 'N/A' Configuration file '/etc/wpa_supplicant.conf' -> '/etc/wpa_supplicant.conf' Reading configuration file '/etc/wpa_supplicant.conf' Priority group 0 id=0 ssid='MyConnection' id=1 ssid='MyConnection' id=2 ssid='MyConnection' id=3 ssid='MyConnection' WEXT: cfg80211-based driver detected SIOCGIWRANGE: WE(compiled)=22 WE(source)=21 enc_capa=0xf capabilities: key_mgmt 0xf enc 0xf flags 0x0 netlink: Operstate: linkmode=1, operstate=5 Own MAC address: xx:xx:xx:xx:xx:xx wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0 wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0 wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0 wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0 wpa_driver_wext_set_key: alg=0 key_idx=4 set_tx=0 seq_len=0 key_len=0 ioctl[SIOCSIWENCODEEXT]: Invalid argument Driver did not support SIOCSIWENCODEEXT wpa_driver_wext_set_key: alg=0 key_idx=5 set_tx=0 seq_len=0 key_len=0 ioctl[SIOCSIWENCODEEXT]: Invalid argument Driver did not support SIOCSIWENCODEEXT wpa_driver_wext_set_countermeasures RSN: flushing PMKID list in the driver Setting scan request: 0 sec 100000 usec WPS: UUID based on MAC address - hexdump(len=16): 16 3b d8 47 9e 24 50 89 96 16 6d 66 35 f3 58 37 EAPOL: SUPP_PAE entering state DISCONNECTED EAPOL: Supplicant port status: Unauthorized EAPOL: KEY_RX entering state NO_KEY_RECEIVE EAPOL: SUPP_BE entering state INITIALIZE EAP: EAP entering state DISABLED EAPOL: Supplicant port status: Unauthorized EAPOL: Supplicant port status: Unauthorized Added interface eth1

  Read the article

• Installed over 4G RAM on 32-bit OS? [closed]

  - by kai

  Possible Duplicate: 32-bit Windows Server address > 4GB RAM - How? I know that for 32-bit OS, the addressable memory space for each process is "4G" (maybe just 3G in user space...). If I have a 8G RAM, is it correct that all of the processes can still utilize (shared) these 8G memory but each of them are limited to a maximum 4G? Or the whole system only can see and utilize 4G out of 8G and thus having 8G RAM on a 32-bit OS is the same as having 4G RAM on it?

  Read the article

• Way to auto resize photos before uploaded to cloud service?

  - by AndroidHustle

  I love using auto syncing services to have my photos taken with my smartphone stored on a cloud storage service. One problem though is that the photos are uploaded in high resolution and takes up a lot of space on the drive. I wonder if any one knows of a service/strategy to have the auto uploaded photo resized to have it occupy less space when auto stored? That is, without me having to take the photos with lesser quality, I still want photos taken with the highest quality since I may take a photo I really like.

  Read the article

• Connecting to my home router web interface from work

  - by Joe

  Hi, I'm trying to connect to my home router web interface from work. I use dyndns, because I don't have a static IP at home, and it works perfectly from any other place except my workplace (update: I made a mistake, see edit below). When trying to access the web interface from work I get a "500 Server Error" with the code: SERVER_RESPONSE_RESET. I'm not trying to use any protocols such as remote desktop, I'm only trying to access the web interface. I can access any other web page from my workplace with no problems, and I think my router web interface is like any other web page, isn't it? I thought maybe my work place proxy blocks addresses of services like dyndns, so I also applied another trick. Since I have a web page on my own domain (say www.mydomain.com) which I can access from work, I tried adding a CNAME to my domain which is linked to the dyndns address (router.mydomain.com). This way if anyone enters the address router.mydomain.com from anywhere, they reach my home router web interface, and there's no way of knowing it's a dyndns address (or is there?). However, it still doesn't work from my workplace (I get the same error message). Any ides? Edit: I'm sorry to say I made a mistake earlier. I used to be able to access my home router web interface from my old workplace, and I thought it was still possible since I don't recall making any configuration changes. However, after reading the replies, I went over to my old workplace and checked, and it doesn't work from there either. I'm very sorry for giving out wrong and misleading information about my problem. So to summarize: my problem is that I can't access my home router web interface from anywhere.

  Read the article

• Extending C drive not possible

  - by gokul

  This is my computer partition list. You can see my C drive is running very low on disk space. I wanted to extend my disk space, so I used mmc Disk managment to shrink a volume, but I can't extend it to the C drive because the extended volume in dropdown list of C is not clickable. I've tried many packages, but none were able to do it. My C drive is simple, basic, NTFS, healthy (boot, crash dump, primary partition). The MMC Windows: What should I do?

  Read the article

• Windows 7 can't make back up

  - by J. Pablo Fernández

  I've been trying to get Windows 7 to make a backup for a week or so. I'm backing up to a local NAS and I'm getting this error: Windows Backup: Troubleshooting Options Check your backup Windows Backup could not create a zip file. This could be because the drive that Windows is installed on does not have enough space or it could be a temporary error. Make sure you have at least 400 MB of free space and try again. Backup time: 2009-09-07 14:48 Backup location: \VANGELIS\Shared\Backup\lennon\ Error code: 0x81000015 My local hard disk has 290GB free and my NAS has 200GB free. Any ideas what might be wrong?

  Read the article

• Provision storage in SAN encironment

  - by wildchild

  hi,.. Can somebody help in understanding how Lun Provisioning is done in clariion based on client requirement. Say, a client needs one 50 GB space on the host( for application) ,two -350 GBs ( for DB and stuff) on the same host and i have 4 raid groups with space of 200 GB in one 50 GB in second and 400 GB and 400GB in rest two all having 5 disks. And , I 'm using Raid 5 only. How do i provision keeping performance in mind( so that performance hit is not there)?..And i need to understand the concept of meta head as well. Please help me by elaborating the above scenario..I am learning to provision storage in non productive environment( b'fore going ahead and working on client prod server) and i have been learning a lot from SF ...I request the seniors here to help me understand it better. Thanks for reading

  Read the article

• Solaris 10 invalid ARP requests from 0.0.0.0? Link up/down every hour or 2

  - by JWD

  The guys at the data center where I'm hosting a server running Solaris 10 are telling me that my server is making a lot of invalid arp requests. This is an example of a portion of what was sent to me from the logs (with Mac addresses and IP addresses changed). [mymacaddress]/0.0.0.0/0000.0000.0000/[myipaddress]/[Datestamp]) It's being logged every hour. I don't see anything in the arp tables (arp -a) or routing tables (netstat -r) and I don't see anything relating to 0.0.0.0 when snoping the arp requests. The only place I see any reference to 0.0.0.0 is if I do netstat -a for the SCTP SCTP: Local Address Remote Address Swind Send-Q Rwind Recv-Q StrsI/O State ------------------------------- ------------------------------- ------ ------ ------ ------ ------- ----------- 0.0.0.0 0.0.0.0 0 0 102400 0 32/32 CLOSED But not really sure what that means. Doesn't seem like I can disable SCTP. There are some tunable SCTP parameters but it's not something I'm familiar with. Do I have to add changes to /etc/system? Looks like sctp_heartbeat_interval might be what I need to change? If it makes any difference, I have a few solaris zones running on this server, each with their own IP address on a virtual interface. eth0:0, eth0:1, etc. Does anyone have any idea what might be causing this and how to stop it? I think the switch I'm connected to doesn't like it and momentarily drops the connection. Is there anyway to at least block those requests using ipfilter or something else? Update: This was happening more frequently but now it seems to be happening roughly every hour or every two hours. It's not consistent. I tried setting setting the link speed and duplex to match the switch port and that seemed to make it stop happening for a few hours but then it started again.

  Read the article

• Temporary file storage - script for webserver

  - by Chris

  I'm looking for a script (preferably php) which I can use for to temporarily exchange files. I had such a script before (it was written in flash), but - damn - just can't find it anymore. Here the features I'm looking for: I have a logon, which allows me to create "upload spaces". for these "upload spaces" I define a time how long the space will be available for (until the files are deleted), and who can access it - in the means of typing in an email, and that user gets a link with the "online space", user ID and password. the other user then clicks on the link and uploads the file, and I get (preferably) an email should there be any file changes I get an email before the content gets deleted Now, 3 additional things: - it should be open- source - run on linux (preferably lamp) - no, I dont wanna use dropbox or similar :p Thanks in advance everybody, Cheers Chris

  Read the article

• starting oracle 10g on ubuntu, Listener failed to start.

  - by tsegay

  I have installed oracle 10g on a ubuntu 10.x, This is my first time installation. After installing I tried to start it with the command below. tsegay@server-name:/u01/app/oracle/product/10.2.0/db_1/bin$ lsnrctl LSNRCTL for Linux: Version 10.2.0.1.0 - Production on 29-DEC-2010 22:46:51 Copyright (c) 1991, 2005, Oracle. All rights reserved. Welcome to LSNRCTL, type "help" for information. LSNRCTL> start Starting /u01/app/oracle/product/10.2.0/db_1/bin/tnslsnr: please wait... TNSLSNR for Linux: Version 10.2.0.1.0 - Production System parameter file is /u01/app/oracle/product/10.2.0/db_1/network/admin/listener.ora Log messages written to /u01/app/oracle/product/10.2.0/db_1/network/log/listener.log Error listening on: (DESCRIPTION=(ADDRESS=(PROTOCOL=IPC)(KEY=EXTPROC1))) TNS-12555: TNS:permission denied TNS-12560: TNS:protocol adapter error TNS-00525: Insufficient privilege for operation Linux Error: 1: Operation not permitted Listener failed to start. See the error message(s) above... my listener.ora file looks like this: # listener.ora Network Configuration File: /u01/app/oracle/product/10.2.0/db_1/network/admin/listener.ora # Generated by Oracle configuration tools. SID_LIST_LISTENER = (SID_LIST = (SID_DESC = (SID_NAME = PLSExtProc) (ORACLE_HOME = /u01/app/oracle/product/10.2.0/db_1) (PROGRAM = extproc) ) ) LISTENER = (DESCRIPTION_LIST = (DESCRIPTION = (ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC1)) (ADDRESS = (PROTOCOL = TCP)(HOST = acct-vmserver)(PORT = 1521)) ) ) I can guess the problem is with permission issue, But i dont know where I have to do the change on permission. Any help is appreciated ... EDIT## When i run with the command sudo, i got this tsegay@server-name:/u01/app/oracle/product/10.2.0/db_1$ sudo ./bin/lsnrctl start LSNRCTL for Linux: Version 10.2.0.1.0 - Production on 30-DEC-2010 01:01:03 Copyright (c) 1991, 2005, Oracle. All rights reserved. Starting ./bin/tnslsnr: please wait... ./bin/tnslsnr: error while loading shared libraries: libclntsh.so.10.1: cannot open shared object file: No such file or directory TNS-12547: TNS:lost contact TNS-12560: TNS:protocol adapter error TNS-00517: Lost contact Linux Error: 32: Broken pipe

  Read the article

• Windows cannot access my external harddisk partition but all partition managers can

  - by Ashish

  Some weird problem happened to my Maxtor 500GB external harddisk, it all started when it once freezed during some operation. Now when I insert the drive in a USB slot, Windows asks me to format it, and if I try to open the drive from my computer it says, "not accessible".. I tried most of the major partition managers and partition recovery software. All of these can see and access my partition normally. It showing the free space and used space correctly. But Windows can't. Please help me out. Including a screenshot: On the left side, the partition manager can access and see my data in the corrupted partition, and on the right side Windows can't

  Read the article

• Video Hosting External or Internal?

  - by user69334

  I have a client who wants to offer videos for downloading or streaming on his website. Now we have hosting for him, which is wonderful: it's reliable and fast, offers unlimited space and databases BUT it only offers 10GB in bandwidth. The videos could easily be placed on his server (unlimited space) but the bandwidth is a real problem. Now I am wondering if he would purchase external hosting for his videos, and people would want to download them, woould this still eat up all his available bandwidth in no time, because the download request would go via his site, or is there a way to circumvent this?

  Read the article

• Customize side panel in Internet Explorer 9/Windows 7

  - by Kari

  I use Internet Explorer 9 with all the horizontal toolbars except the tab bar invisible to maximize vertical space. I have plenty of room at the side so I have the Favorites/Feeds/History panel open, usually on Favorites to replace the Favorites bar. I'd like to customize the shortcuts in this panel to display as large icons, similar to when you set the display in Windows Explorer to Large Icons and, long shot... change the backround color. The side panel does appear to be just a Windows Explorer window but it seems immune to any kind of tampering or customization, mainly because right clicking is disabled on the empty space. Changing browsers is not going to happen but can someone help out here?

  Read the article

• data recovery from unallocated harddisk partition

  - by user42151

  Hi I accidentally deleted a partition which mainly served as space I put my data, labeled D: drive. The partition wasn't subsequently formatted though, following the delete incident. Obviously the D: drive doesn't show up as it usually does when I run Windows 7. In the "Computer Management", on clicking the Disk Management I clearly see the space is now labled as unallocated. question: How do I go about recovering my data. Perhaps what the effective data recovery software I can use to resolve this issue. Thanks

  Read the article

• data recovery from unallocated harddisk partition

  - by user36007

  Hi, I accidentally deleted a partition which mainly served as space I put my data, labeled D: drive. The partition wasn't subsequently formatted though, following the delete incident. Obviously the D: drive doesn't show up as it usually does when I run Windows 7. In the "Computer Management", on clicking the Disk Management I clearly see the space is now labled as unallocated. question: How do I go about recovering my data. Perhaps what the effective data recovery software I can use to resolve this issue. Thanks

  Read the article

• data recovery from unallocated harddisk partition

  - by user36007

  Hi, I accidentally deleted a partition which mainly served as space I put my data, labeled D: drive. The partition wasn't subsequently formatted though, following the delete incident. Obviously the D: drive doesn't show up as it usually does when I run Windows 7. In the "Computer Management", on clicking the Disk Management I clearly see the space is now labled as unallocated. question: How do I go about recovering my data. Perhaps what the effective data recovery software I can use to resolve this issue. Thanks

  Read the article

• E-mail duplication problem

  - by Gavin Osborn

  I have taken out a hosting agreement with a well respected hosting provider for a couple of internet facing servers. We have deployed several applications to these servers which send various e-mails back to us for reporting purposes. Context: Each server runs Windows Server 2003 R2 with the IIS 6.0 SMTP service installed. Each application is configured to use the local instance of IIS to send e-mails. The external IP address of each server is mapped to a particular domain eg: server1.mydomain.com server2.mydomain.com These e-mails are sent from a company domain name and not the domain name of the hosted servers (eg: [email protected]) Symptoms: A small number (<1%) of e-mails sent from these applications appear to be duplicated. These are exact duplicate in terms of both content and message headers. The Fix: I contacted my hosting provider and they told me this was a common problem & instructed me to: Change the HELO response of your mail server service to a FQDN (server1.mydomain.com && server2.mydomain.com) Create a DNS A record that resolves the FQDN of your mail server to the primary IP address of your sending mail server. Create a PTR record that resolves your primary IP address back to your mail server's FQDN In the sending domain's (mycompanydomain.com) DNS zone file, add the appropriate SPF record for your hosted servers. eg: v=spf1 a mx include:mydomain -all The Problem Continues: I made all of the changes as prescribed above, I was a little hesitant because these steps seemed to suggest they were more for stopping your messages getting blocked than they were for stopping them from being duplicated - but I am certainly no expert in these matters. It has been 5 days since I applied this fix and the problem still persists. I am certain that these problems are not a bug in the software because they are 4 different applications installed on 2 different servers, all of whom are exhibiting this strange behaviour. This behaviour has also not been seen in our UAT environment. Were my hosts correct to suggest this fix? If not, does anyone know what could be the cause of this problem? Many Thanks

  Read the article

• Unable to access network resources through VPN

  - by fbueckert

  I'm currently attempting to connect one of our computers in the office to a client VPN. My development machine is running Windows 7, and can connect and see resources just fine. The problem computer is running Windows XP. They're both within the same network. Using the same credentials at both computers, the VPN connection (using the built in Windows network connections) works just fine. So far, so good. An IP address is assigned, and comparing both machines shows they're still in the same subnet. The problem is that the XP machine cannot see ANY of the computers in the client network. I tried a tracert to a target machine on the Windows 7 box, and the first item that comes up is the .0 address. Pinging it gives responses. Trying it on the Windows XP machine, however, comes up with just timeouts. Trying to trace to www.google.com allows the address to resolve (probably part of the cached resolutions), but results in just timeouts. I double-checked to make sure that the Windows firewall was not on, and trying to open the settings brings up a notification that the firewall service wasn't running, which leads me to believe that it's definitely not on. From my best guess, I've managed to connect the XP machine to a black hole of some sort. There's obviously something strange going on, but I'm not sure where I should be looking.

  Read the article

• Windows 8 Pro Hyper-V guest with no internet

  - by Perplexed

  Trying to get this working on my Windows 8 Pro machine. I created an External Switch Assigned the newly available adapter to a Guest machine with Win 2008 os. My host has internet connection. Host can ping Guest, Guest cannot ping Host. Guest has no internet connection. Pasting the ip of both host and guest. Your help appreciated. HOST ========================== Ethernet adapter vEthernet (EXTSW01): Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Hyper-V Virtual Ethernet Adapter #2 Physical Address. . . . . . . . . : 9C-B7-0F-0F-D7-D0 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::5434:a9fd:8611:d207%54(Preferred) IPv4 Address. . . . . . . . . . . : 192.168.0.15(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : Saturday, September 8, 2012 12:34:44 PM Lease Expires . . . . . . . . . . : Saturday, September 15, 2012 12:34:44 PM Default Gateway . . . . . . . . . : 192.168.0.1 DHCP Server . . . . . . . . . . . : 192.168.0.1 DHCPv6 IAID . . . . . . . . . . . : 916240141 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-17-DC-C9-2C-9C-B7-0D-0D-D7-D0 DNS Servers . . . . . . . . . . . : 64.71.255.999 NetBIOS over Tcpip. . . . . . . . : Enabled GUEST ========================== Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Microsoft Virtual Machine Bus Network Adapter Physical Address. . . . . . . . . : 00-15-5D-3F-0F-00 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::953f:ec5c:5d84:1b50%11(Preferred) IPv4 Address. . . . . . . . . . . : 192.168.0.20(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 0.0.0.0 DHCPv6 IAID . . . . . . . . . . . : 234886493 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-17-DD-2F-29-0F-15-5E-00-0F-00 DNS Servers . . . . . . . . . . . : ::1 127.0.0.1 NetBIOS over Tcpip. . . . . . . . : Enabled

  Read the article

• Losing partitions after every reboot

  - by Winston Smith

  I have an Acer laptop with one hard disk, which up until yesterday had 4 partitions: Recovery Partition (13GB) C: (140GB) D: (130GB) OEM Partition (10GB) I read that the OEM partition has all the stuff needed to restore the laptop to the factory settings, but since I'd already created restore disks and I needed the space, I wanted to get rid of it. Yesterday, I used diskpart to do that. In diskpart, I selected the OEM partition and issued the delete partition override command which removed it. Then I extended the D: partition into the unused space using windows disk management. Everything worked fine, until I rebooted my laptop, at which point the D: drive vanished. Looking in windows disk management again, I can see that there's an OEM partition of 140GB, which is obviously my D: drive. So I used EASEUS Partition Master and assigned a drive letter to the 'OEM' partition and I was able to access my files again. However, every time I reboot, it reverts back. How do I fix this permanently?

  Read the article

• Internet Explorer changes brightness

  - by Sale

  I have a very annoying problem with IE8 on Vista: My screen brightness changes when I view a page with IE. It slowly dimms brightness some 20% - enough to be noticeable. This seems to be dependent on the OVERALL brightness of the page viewed or of the amount of bright space on the page... sometimes it dimms down if the page is bright, sometimes the complete different, it dimms when lot of dark space is on the page. I know this sounds weird, I cannot describe it better. It takes about one,two seconds from on brightness level to the other. This ONLY occurs in IE - not in Word or any other application. Please help! This dimming is very stressfull for my eyes.

  Read the article

• Large temp files created in Windows Server 2003 temp folder

  - by BlueGene

  I'm managing a Windows Server 2003 with around 30 GB space in primary partition. A couple of times the server has crashed with error message saying that the C: drive is full. After searching folders to free up space, I found that lot of temp files being created in C:\WINNT\Temp and some of them of enormous size with more than 2GB. The temp files have common name, Efs###.tmp. Since we encrypt files frequently using Windows's EFS, I initially suspected Windows encryption. But after reading the documentation, I found that Efs###.tmp are in fact created by EFS but they are created only under the folder which you're currently encrypting, not in Temp folder. This looks very strange since Efs##.tmp files shouldn't be created under C:\WINNT\Temp unless someone tried to encrypt that Temp folder itself. The server has Tivoli Backup client. Could that be messing with windows Encryption? Can anyone shed some light on what could be causing the issue?

  Read the article

• Exim: send every emails with a predefined sender

  - by Gregory MOUSSAT

  We use Exim on our servers to send emails only from local automated users, as root, cron, etc. We have to specify every possible users into /etc/email-addresses. For example: root: [email protected] cron: [email protected] backup: [email protected] This allow us te receive every email generated. The problem is when we add a user for whatever reason (for example when we add a package, some add a user), we can forget to add this user to /etc/email-addresses. Most of the time it's not a problem, but this is not clean. And the overall method is not clean. We'd like to configure Exim to send every emails with the same source address. i.e. every sent email comes from [email protected] One way could be to use a wildcard or a regular expression into /etc/email-addresses but this is not supported. I don't currently understand Exim enought to figure out how to modify this in a way or another. Ideally, Exim should look into /etc/email-addresses first, and if no match it use the predefined address. But this is very secondary. There are two places where this address is used: 1. when Exim send the FROM: command to the smtp server 2. inside the header edit: The rewrite section is the original one from Debian begin rewrite .ifndef NO_EAA_REWRITE_REWRITE *@+local_domains "${lookup{${local_part}}lsearch{/etc/email-addresses} \ {$value}fail}" Ffrs *@ETC_MAILNAME "${lookup{${local_part}}lsearch{/etc/email-addresses} \ {$value}fail}" Ffrs .endif (comments removed)

  Read the article

• Exchange 2010 sends out spam.

  - by Magnus Gladh

  Hi. I have an Exchange Server 2010, that uses a smart host to send out mails. A day ago the owner of smart host contact us and told us that we send out spam. I have try different open relay test on the net and all of them come back saying that this server is secured and can not be used as relay server. But I can see in my Exchange Queue Viewer that it keeps coming in new messages. Here is an example of how it looks. Identity: mailserver\3874\13128 Subject: Olevererbart:: [email protected] Pfizer -75% now Internet Message ID: <[email protected]> From Address: <> Status: Ready Size (KB): 6 Message Source Name: DSN Source IP: 255.255.255.255 SCL: -1 Date Received: 2010-12-09 21:46:22 Expiration Time: 2010-12-11 21:46:22 Last Error: Queue ID: mailserver\3874 Recipients: [email protected] How can I secure our exchange server more, to stop this from happening? Could I have got an virus that hooks up to our exchange server and send mail throw that? As I can see the From Address is always <, is there someway that I can stop sending mails that don't have a from address that I describe? Pleas help

  Read the article

• Linux VLAN Bridge

  - by raspi

  I have home network with VLANs, one for LAN, one for WLAN and one for internet. I'd like to use bridging so that instead of configuring these same VLANs to every machine, they had own VLAN ID and bridges were LAN, WLAN and internet. I've tried it but for some reason keep-alive/ttl seems to get broken because SSH sessions etc suddenly disconnects. We have this same setup working in workplace for 4+ years with 100+ customers but it's custom firewall/router hardware so accessing it is impossible. I know that it runs Linux. So what is Debian/Ubuntu default network settings doing wrong or is it just NIC driver/hw problem? I've tried to mess araund with ttl etc settings without any luck. The bad stuff is happening in the bridge because current VLAN-only setup works fine. interfaces: auto lo iface lo inet loopback # The primary network interface allow-hotplug eth0 allow-hotplug eth1 iface eth0 inet static iface eth1 inet static auto vlan111 auto vlan222 auto vlan333 auto vlan444 auto br0 auto br1 auto br2 # LAN iface vlan111 inet static vlan_raw_device eth0 # WLAN iface vlan222 inet static vlan_raw_device eth0 # ADSL Modem iface vlan333 inet static vlan_raw_device eth1 # Internet iface vlan444 inet static vlan_raw_device eth0 # LAN bridge iface br0 inet static address 192.168.0.1 netmask 255.255.255.0 bridge_ports eth0.111 bridge_stp on # Internet bridge iface br1 inet static address x.x.x.x netmask x.x.x.x gateway x.x.x.x bridge_ports eth1.333 eth0.444 bridge_stp on post-up iptables -t nat -A POSTROUTING -o br1 -j MASQUERADE pre-down iptables -t nat -D POSTROUTING -o br1 -j MASQUERADE # WLAN bridge iface br2 inet static address 192.168.1.1 netmask 255.255.255.0 bridge_ports eth0.222 bridge_stp on Sysctl: net.ipv4.conf.default.forwarding=1

  Read the article

< Previous Page | 223 224 225 226 227 228 229 230 231 232 233 234  | Next Page >