Search Results

Search found 10963 results on 439 pages for 'documentation generation'.

Page 228/439 | < Previous Page | 224 225 226 227 228 229 230 231 232 233 234 235  | Next Page >

• Change Command Prompt width from the Command Line

  - by Starkers

  Don't really know what more I can say really. That window captured below will simply not get any larger. Are there some settings somewhere that will allow me to resize it? See, this limited window thing has left me in a bit of a pickle. Basically I've created an application with a command line GUI (With Ruby's Curses Library), and while everything works beautifully on OSX and Ubuntu Terminals, with Command Prompt, if the Curses Windows are larger than the Command Prompt window as shown below, the whole application crashes with a 'window already closed' error. So, is there a setting that allows users to resize their Command Prompt window, something that I'll have to put in the documentation. Here's what the holy grail answer would, be though: Is there a way to do this from the command line? Could my application detect if the Command Prompt it's running on is of fixed width, and actually programatically run the command to allow the Command Prompt window to be enlarged? Or at least give the user a helpful error message?

  Read the article

• smartctl or hddtemp for xvda [on hold]

  - by HST

  I'm trying to check the state of the drives on a remote server running Debian wheezy. I'm using a software RAID10 on top of, I guess, xen, since the entries in /dev are /dev/xvda and /dev/xvdb But it I try smartctl -a /dev/xvda I get /dev/xvda: Unable to detect device type Smartctl: please specify device type with the -d option. I've tried various device type guesses, none work Similar problem with hddtemp, which reports ERROR: /dev/xvda: can't determine bus type (or this bus type is unknown) I've searched the smartmontools documentation, but can't find any discussion of virtual disks. . . How do I get behind the virtualisation to something smart tools or hddtemp can work with?

  Read the article

• One-way forest trust between geographically distributed forests using Server 2008 R2

  - by bwerks

  Hi all, I'm planning out a joinder between two domains, as would take place with contracting companies. Forests A and B exist in distant sites, and there is to be a one-way forest trust so that domain users in Forest A can be authenticated on machines in Forest B. In order to facilitate this, each forest's domain controller must be able to contact each other in order to set up & confirm the trust, but my question is what underlying networking magic must take place beneath it. So far the prevailing approach has been to maintain a VPN connection between the two sites, but the technet documentation seems to indicate that DNS forwarding may be the way to go. Is this the case? Furthermore, if DNS will suffice, does that mean that there must be a server running DNS on boundary servers in each domain so that they can be reached from across the internet? How must they be configured? Thanks!

  Read the article

• Word 2013: Get the page number for the previous page

  - by Mike Anthony

  I'm trying to accomplish something very simple in Word 2013, but the feature does not seem to be available, nor can I work it out with field codes. I simply want to include, on multiple pages, "continued from page n". In terms of field codes, I have tried this: { = PAGE - 1 \* MERGEFORMAT } It just tells me that PAGE is not a defined bookmark. Is there any way that this can be done? Edit: Per documentation I found somewhere, I also tried this - but with no luck: { = { PAGE } - 1 } This just threw Syntax Error, { back, which leads me to assume that it's incompatible with newer versions of Word.

  Read the article

• How to avoid tilde ~ in Bash prompt?

  - by Jirka

  Hello! I have set my prompt in bash in a such way that I can use it directly in scp command: My current PS1 string: PS1="\h:\w\n$" And the prompt looks like this: lnx-hladky:/tmp/plugtmp $ What I don't like at all is the fact that $HOME directory is displayed as tilde. Can this be avoided? It's causing problems when switching between different users. Example: lnx-hladky:~/DOC $ Documentation says: \w : the current working directory, with $HOME abbreviated with a tilde \W: the basename of the current working directory, with $HOME abbreviated with a tilde Is there any possibility to avoid $HOME being abbreviated with a tilde? I have found one way around but I feel like it's overcomplicated: PROMPT_COMMAND='echo -ne "\e[4;35m$(date +%T)\e[24m$(whoami)@$(hostname):$(pwd)\e[m\n"' PS1=$ Can anyone propose a better solution? I have a feeling it's not quite OK to run so many commands just to get prompt. (date,whoami,hostname,pwd). Thanks a lot! Jirka

  Read the article

• Trying to understand why VLANs need to be created on intermediate switches

  - by Jon Reeves

  I'm currently studying for the Cisco switching exam and having trouble understanding exactly how 802.1q tagging works. Given three daisy chained switches (A,B, and C) with trunk ports between them and VLAN 101 defined on both end switches (A and C), I'm not sure why the VLAN also needs to be defined on the middle one (B)? Note that I am not disputing that it does need to be configured, I'm just trying to understand why exactly. As I understand it, traffic from VLAN 101 on switch A will be tagged as it goes through the trunk to switch B. According to the documentation I have read, trunks will pass all VLANs by default, and the .1q tag is only removed when the frame leaves through an access port on the relevant VLAN. From this I would expect switch B to simply forward the tagged frame unchanged through the trunk to switch C. Can anyone shed some light on how switch B processes this frame and why it does not get forwarded through the other trunk ?

  Read the article

• How do you confirm network adapter is gigabit capable?

  - by StrandedPirate

  Upgrading my network to gigabit speeds and don't know how to determine if the NIC in one of the systems is capable of gigabit speed. The documentation from the manufacturer states this: Network adapter 10/100/1000 Ethernet LAN on system board However when I go to the properties of the NIC under Speed & Duplex my only options are: 10 Mb Full 10 Mb Half 100 Mb Full 100 Mb Half Auto Is there a command line I can run that will give me more detail about the NIC? Windows 7 x64 OS New Info: The new switch I just bought has a light to indicate 1000Mbps. I can tell from the light that this NIC is indeed negotiating at 1000Mbps but I'd still like to know how to determine this from the console in windows.

  Read the article

• Monitoring IIS with SNMP

  - by Shtong

  Hello, I'm trying to monitor IIS using the Windows integrated SNMP service (for versions 2000, 2003 ans 2008 of Windows Server, but i'm doing my experiments on a 2008 R2 box). So far I was able to install the SNMP service, and query mib-2 values without problems. Now, I'm having trouble to monitor IIS informations, as the SNMP service does not seem to know about the .iso.org.dod.internet.private.enterprises.microsoft.software.internetServer OIDs. Walking the entire SNMP tree only gets the mib-2 stuff as well as the names of some services, but that's it. I did't find anything interesting in the service configuration panel. So how do I configure this service to get IIS information, or other WMI data for that matter (I installed the SNMP WMI Provider) ? I can't find any documentation about that !

  Read the article

• What happens when Oracle's Enterprise Single-Sign-On database goes down? [migrated]

  - by Unai

  We're working on setting up Oracle's Enterprise Single-Sign-On with High Availability. At the moment every component provides HA except our database backend (i.e. we have just one instance). While conducting some kick-the-plug tests we learnt that the ESSO system works even with the database turned OFF. This was a nice surprise but now we need to understand what are the implications of a database failure; sure the sessions might be handled on the application servers and the policies might have been cached but... for how long? how big is this cache? what is the role of the database? I would appreciate if anyone shares her/his experience and/or points out to documentation that covers this. Thank you so much.

  Read the article

• Windows 2008 R2 Server Core Disk Space Requirements/Recomendations

  - by Richard West

  I'm in the preparation stage to roll out a few Windows 2008 R2 Server Core in my VMware ESX environment. In looking over the documentation it looks like Server Core can operate in a little as 6.5 GB of hard drive space. Less disk space required. A Server Core installation requires only about 3.5 gigabytes (GB) of disk space to install and approximately 3 GB for operations after the installation. I am curious as to anyone’s real world experience and recommendations with regard to this requirement. Is it realistic? A little bit about our environment: Less than 25 users, and around 75 computers/servers in our current AD system. These systems will be responsible for normal AD operations and print servers for 5 printers - nothing to big here.

  Read the article

• How does syslog-ng handles flush_lines(0) ?

  - by Luke404

  I wanted to make sure my syslog-ng was doing async logging. Reading through the documentation I see the flush_lines() option for file() destinations, if unspecified, will use the global default. Then I see that the global setting defaults to 0 but it doesn't explain what that means. Is it going to do synchronous logging when set to 0? is it going to buffer an unlimited number of lines (flushing just every flush_timeout() number of seconds)? is it going to bite me?

  Read the article

• A minimal Linux distribution for my ASUS EEE PC

  - by Andrioid

  I recently bought myself a ASUS EEE 1000HE and I intend to use it for note-taking and light browsing at the University. The machine has a 10" screen so the interface needs to be very compact. I've already tried: EEEbuntu: Very nice driver support and out of the box experience. But I feel that it is too slow booting and the general experience is too heavy in my opinion. Moblin 2: Looks very cool, boots just fine but is way too unstable to use. Also find it annoying that I can't find hotkey documentation anywhere. Any Netbook OS recommendation welcome (although those specific to my model would be great). There is an entire jungle of distributions out there, so if you've been on a safari, please share your experience.

  Read the article

• CloudFormation - How to start a Windows Service with cfn-init

  - by Edwin

  I'm creating a CloudFormation Stack that will install and start a service on a Windows Instance. I've figured out how to install the service, but how do I start the service using cfn-init? The examples seem to all use linux, as there is a reference to "sysvinit" How do I structure AWS::CloudFormation::Init so that cfn-init will start windows services after installing them? Do I leave in the sysvinit, replace it with something else, take it out? ps: I'm referring to how to start services by providing information to AWS::CloudFormation::Init.services. Also, It would be nice to know how "packages" work for windows. AWS's announcemnet says that packages are supported on Windows but there is no Windows specific documentation

  Read the article

• Overlapping appointments in Outlook 2003

  - by iansinke

  I'm using Microsoft Outlook 2003 (Home and Student, if that makes any difference, which I doubt) as my calendar, and I have one minor gripe: it can't really handle appointments that don't begin and end right on the half-hour mark. For instance, if I have a class that ends at 9:22 AM and another class that begins at 9:27 AM, they will appear to overlap in the day view. Not a big deal, but it bugs me nonetheless. Anybody know of a hack or patch that will fix this issue? I've searched the Outlook documentation as well as Google to no avail.

  Read the article

• Directly editing IIS 7 applicationHost.config configuration file

  - by lunadesign

  I know that IIS 7+ now uses XML config files instead of the metabase. I also know that if I edit a web.config file for a given site, IIS automagically detects the changes and implements any corresponding config changes. However, does this also apply to the server-level applicationHost.config settings file? (Its usually located in C:\windows\system32\inetsrv\config.) Specifically, is it safe to carefully edit this file instead of using IIS Manager or the appcmd command line utility? I couldn't find anything in the documentation that said it was okay or not okay to do this. I'm curious because I have to change the bindings for numerous sites from one IP to another. It would be much faster to simply do a global search and replace for the IP address in the config file instead of manually editing a few dozen sites in the GUI.

  Read the article

• Mac OSX Server: svn via ssh command line and encrypted passwords.

  - by Ben Clayton

  Hi all. When I log into our mac mini server running OSX 10.6 via ssh and use svn I get the message: ATTENTION! Your password for authentication realm: can only be stored to disk unencrypted! You are advised to configure your system so that Subversion can store passwords encrypted, if possible. See the documentation for details. You can avoid future appearances of this warning by setting the value of the 'store-plaintext-passwords' option to either 'yes' or 'no' in '/Users/xxxxxxxx/.subversion/servers'. I dont' want to store the password unencrypted though. I've found some details on how to use GNOME keychain in linux to sort this, but nothing on how to use macosx's keychain. Anyone got any ideas? Thanks a lot!

  Read the article

• MongoDB ReplicaSet Elections when some nodes are down

  - by SecondThought

  I'm trying to get into ReplicaSet concept, and found something weird in mongoDB Documentation: For a node to be elected primary, it must receive a majority of votes. This is a majority of all votes in the set: if you have a 5-member set and 4 members are down, a majority of the set is still 3 members (floor(5/2)+1). Each member of the set receives a single vote and knows the total number of available votes. If no node can reach a majority, then no primary can be elected and no data can be written to that replica set (although reads to secondaries are still possible). (taken from here) So, If I got that right, in the 5-member case mentioned there the one node that's still standing WILL NOT be chosen as primary and the whole set will not get any writes? and that's even if this single node was the last primary before the elections? If it's true there can be many less-radical cases which will end up with a degenerated set. How can we avoid this?

  Read the article

• 'Unsaved Theme' is not appearing when I make a change to a theme in Windows 7

  - by Bernard

  According to personal experience and Microsoft documentation, when an aspect of a theme (wallpaper, border colour, etc) is changed in the 'Personalization' screen of Windows 7, a theme called Unsaved Theme is supposed to be created/exist under the 'My Themes' heading. However, my 'My Themes' section is always empty, and if I change the background by clicking on the Background link at the bottom of the Personalization page, the background changes, but it still shows 'Harmony' as the selected background, and no 'Unsaved Theme' is created. I have no idea how long this has been happening, but I would like to create some themes, but it never acknowledges my changes as it is supposed to.

  Read the article

• How to keep haproxy log messages out of /var/log/syslog

  - by itsadok

  I set up haproxy logging via rsyslogd using the tips from this article, and everything seems to be working fine. The log files get the log messages. However, every log message from haproxy also shows up at /var/log/syslog. This means that once the server goes live, the syslog will be quite useless, as it will be run over with haproxy log messages. I would like to filter out those messages from /var/log/syslog. After going over the rsyslogd documentation, I tried to change the file /etc/rsyslog.d/50-default.conf thus: *.*;auth,authpriv.none;haproxy.none -/var/log/syslog I simply added the ;haproxy.nonepart. After restarting rsyslogd it stopped working completely until I reverted my changes. What am I doing wrong?

  Read the article

• Is there a way to set access to WMI using GroupPolicy?

  - by Greg Domjan

  From various documentation it appears that to change WMI access you need to use WMI to access the running service and modify specific parts of the tree. Its kind of annoying changing 150,000 hosts using the UI. And then having to include such changes in the process of adding new hosts. Could write a script to do the same, but that needs to either connect to all those machines live, or be distributed for later update say in an startup/install script. And then you have to mess around with copying binary SD data from an example access control. I've also found you can change the wbem/*.mof file to include an SDDL but I'm really vague on how that all works at the moment. Am I just missing some point of simple administration?

  Read the article

• How can I convert an OpenOffice document to PDF from the Linux command line?

  - by Norman Ramsey

  I have students who, when asked for PDF, sometimes hand me an OpenOffice document or spreadsheet. file(1) can identify these documents, but I've been unable to discover how to convert them to PDF using the command line. (The man page for ooffice(1) lists an option to print a document but not to convert to PDF.) Google is unhelpful, except for giving me the uneasy feeling that this can't be done without a nifty script in a language I don't know against an API whose documentation I can't find. Can anyone help me solve the problem of converting an OpenDocument to PDF using only the Unix command line?

  Read the article

• Decrypting Windows XP encrypted files from an old disk

  - by Uri Cohen

  I had an old Windows XP machine with an encrypted directory. When moving to a new Win7 machine I connected the old disk as a slave in the new machine, and hence cannot access the encrypted files. Chances don't seem good as documentation warns you: "Do not Delete or Rename a User's account from which will want to Recover the Encrypted Files. You will not be able to de-crypt the files using the steps outlined above." On the other hand, I have full access to the machine, so maybe there's a utility which can extract the keys and use the to decrypt the files... BTW, I didn't have a password in the old machine, if it's relevant. Ideas, anyone? Thanks!

  Read the article

• Unable to access internal network through PfSense WAN port

  - by Sean

  Our branch office is unable to connect to our internal network for some reason. However we can connect to the branch office domain controller from behind PfSense. The following is our setup: |Branch DC - 192.168.0.101 | |Branch Firewall - 192.168.0.2 | |(Internet) | |Local Firewall - 192.168.3.1 | |PFSense WAN port - 192.168.3.100 |PFSense LAN port - 192.168.1.1 | | DC1 - 192.168.1.2|DC2 - 192.168.1.4 Branch DC can ping and connect to PFSense WebGUI on the WAN port successfully (we set this up using the PfSense documentation). DC1 and DC2 can connect outbound to the Branch DC. There seems to be a rule that prevents internal access on the WAN port. However our rules are set to allow all traffic on the LAN and WAN ports. It would be ideal to just disable the firewall altogether since we already have a firewall but when we do this, PfSense doesn't allow any internal traffic at all. I look forward to any assistance and thank you ahead of time.

  Read the article

• Can I use PLink and Pageant with Cygwin's ssh?

  - by Jerph

  I'm now using msysgit because of the GUI tools, which use Putty's Pageant and PLink utilities, but I use Cygwin as a general SSH terminal. I had been using ssh-agent on Cygwin, but that means I have to enter my SSH key passphrases for both SSH key managers. Is it possible to configure all my Unix-port tools (msys, git, cygwin, Ruby Net:SSH, etc.) to use PLink/Pageant instead of ssh-agent? It seems that's the kind of thing PLink was made for, but I can't find documentation on how.

  Read the article

• Installing Windows on HP Proliant Servers without SmartStart

  - by Fitzroy

  I have a PXE server for deploying Windows XP and Windows 7 to workstations. The process is as follows: Boot the workstation from the NIC. Workstation sends a DHCP request. DHCP server responds with an IP address and the location of the PXE server. Workstation downloads WinPE image file from PXE server via TFTP Workstation stores WinPE image file in memory and executes it. Once booted into WinPE, I connect to a network share to gain access to either the Windows XP or Windows 7 installation files. A custom script is launched to guide you through the process of formatting and partitioning the hard drive(s) (using DISKPART and FORMAT). Another custom script asks for details such as the hostname to assign to the workstation. The answers provided are used to build an unattended answer file (SIF [Setup Information File] for WinXP and XML for Win7). The Windows setup EXE is launched, passing the unattended answer file to it as a parameter. The Windows XP and Windows 7 installation sources have been customised to include the drivers for our Dell workstations. They also run a number of scripts upon first booting up to install software packages. This process works very well for our workstations and I would now like to use it for building our servers too. The vast majority of our servers are HP Proliant DL360 G6, DL380 G5 and DL380 G6. They’re running Windows Server 2003 (various editions) or 2008 (various editions). To date, we have always built the HP Proliant servers using the SmartStart CD provided. SmartStart does three useful things for us: Setup RAID with HP Array Configuration Utility (ACU). Installs and configures SNMP Installs various HP Tools for Windows (HP Array Configuration Utility, HP Array Diagnostic Utility, HP Proliant Integrated Management Log Viewer, etc) Using SmartStart I have never had to manually download and install Windows drivers for network, sound, video, etc. I'm not sure if this is because SmartStart copies drivers from the CD during setup, or whether Windows just has the drivers natively in its driver CAB. If I abandon the SmartStart CD in favour of my PXE server I would have to do the following: As I wont have access to ACU, I'll configure the RAID (before booting to the PXE server) by pressing F8 (during the boot process) to access Option ROM Configuration for Arrays (ORCA). Installation of SNMP and the HP Tools will have to be installed once the Windows installation is complete using the Proliant Support Pack. Is this method OK? Is there anything that the SmartStart CD does that I'll be unable to do by other means? Are there any disadvantages to not using the SmartStart CD? Many thanks. UPDATE 05/01/12 I’ve been reading through the SmartStart Scripting Toolkit documentation. The scripting toolkit contains command line tools which work within WinPE and can such things as configure BIOS settings, configure an array and setup ILO. I’m personally not too bothered about configuring BIOS settings as I rarely deviate from the defaults (unless the server is to be a Hyper-V host). I’m not too fussed about being able to configure the array from within WinPE, as I’m happy to just press F8 and use Option ROM Configuration for Arrays (ORCA). Although, if it’s easy enough to do, I will explore this further, as it saves time if everything can be configured from within WinPE. One of the nice features all the tools possess is that you can pass input files to them. EG. Configure one server to your requirements, capture its configuration to a file (using the appropriate tool), you can then use the tool on other servers passing the input file with the captured configuration. Array controller drivers appear to be included with the toolkit along with example of how to incorporate them within a WinPE build. I suppose WinPE won’t be able to see logical volumes (I.E 2x physical disks in a RAID 1 configuration) without the array controller drivers? I mentioned in my post that SmartStart normally installs a bunch of Windows HP tools for you. I’ve had a look today, and if you run the SmartStart CD from within Windows all the tools can be installed. Therefore I can do this after the Windows installation is complete. The SmartStart CD appears to contain a lot Windows drivers. I can customise my Windows 2008 source to incorporate these drivers. However, I understand that incorporating an array controller driver is a little different to most drivers. I believe that you have to provide the driver during the very early stages of the Windows setup. I’m working through the Scripting Toolkit documentation to try and work this out...

  Read the article

< Previous Page | 224 225 226 227 228 229 230 231 232 233 234 235  | Next Page >