Search Results

Search found 8328 results on 334 pages for 'hope i helped'.

Page 228/334 | < Previous Page | 224 225 226 227 228 229 230 231 232 233 234 235  | Next Page >

• Replacing Failing RAID 1 Drive

  - by mrduclaw

  I hope this is a simple question, but I simply don't know anything about RAID. Some time ago I received a machine that, as I understand it, has two drives in it under RAID 1 (or so that one drive is mirrored on the other and appears as just 1 drive to the OS). Recently, one of these drives has started marking a clicking noise and I would like to replace it. I believe the machine has a hardware RAID controller on the motherboard that handles the RAID stuff, but if it matters the Operating System is Windows XP 32-bit. Is the solution to my problem as simple as buying another drive that is of the same capacity and plugging it in where the clicking drive is currently? Or could I possibly lose everything if the drive that's clicking is the one being mirrored on to the other drive? Is there some menu I need to find before unhooking things? Any best practices out there? I'm sure I'm leaving out some required information, so please just tell me what I'm missing. Thanks!

  Read the article

• How to fix UNMOUNTABLE_BOOT_VOLUME (0x000000ED) on my Windows XP DELL laptop?

  - by Neil

  I have a Dell Latitude D410. Running Windows XP. I am receiving the STOP: 0x000000ED (0X899CF030,0XC0000185,0X00000000,0X00000000) Blue screen. Initially, I tried everything specified with the Microsoft KB articles. At this time, I was able to boot into the general safemode. I pulled the hard drive and was able to run chkdsk on it- it noted that it had fixed some errors, but I was still unable to boot. I put a brand new hard drive in the laptop. Windows XP installation worked up until the reboot, at which time the exact same error message came back up. What I have tried (all since the new hard drive was installed): chkdsk /R All suggested solutions in Microsoft KB articles Reseating RAM Opened laptop, reseated all connectors, looked for signs of damage (saw none) Reset BIOS options to default Ran the basic Dell diagnostics I have looked at the current entry:How can I boot XP after receiving stop error 0x000000ED - I am currently in the process of downloading the Ultimate Boot CD to use as a test, but I am not holding out a lot of hope as I really doubt this brand new Hard Drive is bad. Can anyone think of other areas I am missing? Ran MEMTEST86+ V4.10 for 15 passes (overnight). 0 Errors EDIT: FORMATTING

  Read the article

• Install Peppermint OS three on Asus EeePC

  - by Kithoth

  I just had a new Asus EeePC R051CX. Out of the box, the installed OS is Ubuntu 12.04 LTS, but I am trying to install Peppermint OS three (as single boot). Problem. Once on live CD (well, live USB stick...), I'm in trouble in both following situations: Try Peppermint OS Live In this case, the first thing I get is a message reading The system is running in low-graphics mode Your screen, graphics card, and input device settings could not be detected correctly. You will need to configure these yourself. I can solely press "return" to accept, then I have a list of 4 options to answer the question "What would you like to do?". But I simply can't do anything at this moment, except switching to console mode or rebooting (keyboard / mouse controls don't allow me to do anything else). Install Peppermint OS Something I really don't understand... it launches the Ubuntu Recovery Media (which was already installed when I received the device)! Also, it says in the bottom ERROR: This recovery media only functions on Ubuntu systems. All I can do is quit (that is, reboot). One last important thing that comes to my mind: this stick worked just fine on the other computers I've tried it on. I really hope someone could bring me the light, a friend of mine told me how cool this OS is for EeePCs. Don't want to give up! Thanks. Edit I finally could install Peppermint, but not by understanding why I couldn't do it the logical way. Instead, I reinstalled Ubuntu myself (erasing the factory one). Then, I could simply boot on my live USB and perform a fresh install of Peppermint. So, I still don't know how and why the mentioned problem occurred.

  Read the article

• How to get Subversion repository from svn:// and https://?

  - by Hikari

  I know these are noob questions, but I never got my own Subversion running before and I'm kinda lost. I installed VisualSVN in Windows, but it doesn't support svn:// protocol by default, only HTTP or HTTPS. It is working fine over HTTP, and I'm able to manage it from its management tool, see its repositories and get their HTTP-based URL, and from that I'm able to use Tortoise to check out and check in. I'm able to check out from a repository URL using Tortoise: http://Main:90/svn/HikariKrumo/ But I need svn:// protocol for Redmine to access it. Redmine says to support http:// but it reports this error message: The entry or revision was not found in the repository.. And I need HTTPS to access it from Internet. If I can get Redmine to access it from svn:// I can just configure it to use HTTPS in place of HTTP, and I hope it all to works. I like VisualSVN because of its management tool, but I can use another Subversion distro if needed, as long as it supports svn:// and https://. I'm getting crazy on it because it should be simple but I can't get it to work.

  Read the article

• Printer deployment via Group Policy not working on a single system

  - by Aron Rotteveel

  One of my coworkers just got a new laptop running Windows 7 Pro x64. We use a GPO to deploy the printers to every system, but for some reason it is not working on this system. I have been breaking my head over this for the past 3 hours now without any result. The strange thing is that gpresult /H seems to indicate that the GPO did run. The hardware: Laptop: Windows 7 Professional x64 Print server: Windows Server 2008 x64 R1 HP Color LaserJet 2605dn HP LaserJet P2015 Driver packages on server: HP universal printer driver PCL5, both X86 as X64 Oddities and other info: GPO working flawlessly on every other system, including my own Windows 7 Ultimate X64 laptop gpresult /H shows the GPO being ran Windows Firewall completely disabled on the new laptop Below is the output for gpresult /H (in Dutch sadly, but I think you'll recognize it): Beleidsregels Windows-instellingen Printerverbindingen Pad Dominerend groepsbeleidsobject \\Server2008\HP Color LaserJet 2605dn Printers \\Server2008\HP LaserJet P2015 Printers Beheersjablonen Beleidsdefinities (ADMX-bestanden) opgehaald van de lokale computer. Configuratiescherm/Printers Beleid Instelling Dominerend groepsbeleidsobject Beperkingen van point-and-print Uitgeschakeld Printers Like I said, I have been trying to figure this out for the past few hours or so without any result, so you are my last hope. Any help is appreciated.

  Read the article

• Windows 7 boot manager not localized on UEFI systems

  - by Massimo

  I originally posted this on SuperUser because I discovered this behaviour on my home computer, but this seems to be a general issue on UEFI systems, thus I'm posting here too; I also hope someone here can shed some light on what's going on. Italian version of Windows 7 x64 SP1, same installation media used for both situations. When running on BIOS systems, the boot manager is fully localized, both for the loading screen and for the F8 boot menu. When running on UEFI systems, the boot manager always runs in English, even if it's correctly configured to use the it-IT locale, as BCDEDIT clearly shows: Windows Boot Manager -------------------- identificatore {bootmgr} device partition=\Device\HarddiskVolume1 path \EFI\Microsoft\Boot\bootmgfw.efi description Windows Boot Manager locale it-IT inherit {globalsettings} default {current} resumeobject {9ef36aa6-4188-11e3-909d-d32f0c3871c8} displayorder {current} toolsdisplayorder {memdiag} timeout 30 Caricatore di avvio di Windows ------------------- identificatore {current} device partition=C: path \Windows\system32\winload.efi description Windows 7 locale it-IT inherit {bootloadersettings} recoverysequence {9ef36aa8-4188-11e3-909d-d32f0c3871c8} recoveryenabled Yes osdevice partition=C: systemroot \Windows resumeobject {9ef36aa6-4188-11e3-909d-d32f0c3871c8} nx OptIn I also noticed something strange here; the motherboard setup shows "Windows Boot Manager" as the main boot option, while the actual boot disk is listed as the second one. Looks like the Windows Boot Manager is actually being loaded from somewhere else than the first partition of the first disk... what's going on here? Update I've also checked the EFI boot manager using bcdedit /enum FIRMWARE. That one looks correctly localized, too: Boot Manager per firmware --------------------- identificatore {fwbootmgr} displayorder {bootmgr} {9ef36aa4-4188-11e3-909d-d32f0c3871c8} {a30e8550-47e4-11e3-9ad1-806e6f6e6963} timeout 1 Windows Boot Manager -------------------- identificatore {bootmgr} device partition=\Device\HarddiskVolume1 path \EFI\Microsoft\Boot\bootmgfw.efi description Windows Boot Manager locale it-IT inherit {globalsettings} default {current} resumeobject {9ef36aa6-4188-11e3-909d-d32f0c3871c8} displayorder {current} toolsdisplayorder {memdiag} timeout 30 Applicazione firmware (101fffff) ------------------------------- identificatore {9ef36aa4-4188-11e3-909d-d32f0c3871c8} description CD/DVD Drive Applicazione firmware (101fffff) ------------------------------- identificatore {a30e8550-47e4-11e3-9ad1-806e6f6e6963} description Hard Drive

  Read the article

• Video adapter problem on new motherboard

  - by Dmitriy Matveev

  Something bad happened to my PC several days ago. I wasn't near my PC, so I have no idea about what happened it was just halted. When I tried to boot it was entering infinite loops of a few seconds power up (cpu, hdds, etc) and then power down. I've tried to boot the system with no additional components (that includes hdd, video, network adapters and even memory) connected and that didn't solved the problem, so I've made a decision that most likely it's either some a problem with power unit or with motherboard. I've tried to replace my power unit by another one (which was expected to be working) and the problem didn't resolved again. I've bought a new MB (ASUS P5KPL-AM SE) and tried to get it running with my old CPU and memory (I hope it's still alive). Since this MB include on-board video I've tried to run the PC without installation of mine video. The PC wasn't running and the BIOS was beeping one long signal following by two short (Does it means a video problem?). After that I've installed my video adapter to PCI-E slot and tried to boot the system again and the BIOS was beeping the same. I don't get it. I may expect some problem with CPU and/or memory since I don't know what happened to my PC (maybe some power failure or something different), but not with video and not with on-board video on newly bought MB. How can I understand what's wrong with my system now?

  Read the article

• How can I tell if my UPS is functioning properly or not for my PC?

  - by prabha

  For the last two days, my Uninterruptable Power Supply (UPS) has failed to produce the actual back up. So, I charged it for 24hrs and again checked that when the power failed my PC was automatically shut down. But in the time of power no supply from ups bt .......is my ups is working properly or not else there is direct power. It will cause any harm to my pc. my questions are..... Is the UPS functioning properly or not? If not, then will it harm my pc? If it is functioning, will it regulate direct power to pc without any cause? Is my UPS battery not working? What should I do to make my UPS batteries last for at least a year? I am using FRONTECH UPS 600va (Warranty for both ups and battery is expired) I already changed the battery 8 months previously. Note from editor: Tried to make as much sense of this question as I could. I hope I didn't alter the meaning in any way.

  Read the article

• Does OS X support linux-like features?

  - by Xeoncross

  I have been using XP for almost a decade. Contrary to popular belief, it has served me well. In the last 4 years I don't remember ever having it crash on me. It has the most stable GUI I have ever used. However, an OS is only as good as it's GUI AND command line combined. Windows command line is awful and totally useless. So I have been using Ubuntu for a couple years and Debian on my servers. The only problem is that Gnome applications (ubuntu 6-10) constantly crash on me (Ubuntu Studio was the most unstable OS I ever used). I have high quality Gigabyte, MSI, and Asus motherboards and CPU's from old Semprons/Athlons to Celerons/Core 2 Quads. What are the odds that every PC I have ever owned can't remain stable with a linux GUI? Not to mention that Adobe CSx Suite doesn't work on linux. Anyway, I am now looking at moving to a MAC in the hope of finding a stable GUI and a feature-packed command line. Does Mac OS have an integrated command line where I can do linux-like-awesomeness like rsync, ssh, wget, crong jobs, package updates, and git without having an unstable GUI? Basically, until the linux GUI applications get a little better, is OS X what I need?

  Read the article

• A server which uses 2 IPs and is needed to give service (under NAT)

  - by user6004

  I have an internal server, which uses a certain service. This service listens on a port, and speaks on a different port. The problem with the service is that it can't listen and speak on the same IP address, so I have configured 2 IP addresses for that NIC, and so I "solved" the problem with the listening and speaking. I have a problem though... I need that server to be NATed, with a public IP address, and that server needs to be available from the outside (and as only one IP)... The question is, how do I solve the situation here? If I do a NAT for one IP address (the listening port), then he will be able to get requests from the outside, but won't be able to send out traffic (because the other IP won't have NAT). If I do NAT on both of the IPs, then when traffic comes in for the listening port, it won't necessarily arrive to the listening IP, but rather to the speaking one. I hope I made myself clear and that there is a sensible solution here that I am missing.

  Read the article

• ec2 spot instance for daily processing task

  - by chaft

  I don't have much experience as a sysadmin or with amazon aws, so I hope someone can explain in simple terms or refer me to a good guide on how to achieve the below. I have a system running on ec2 and amazon rds getting data in and saving it to the db. I need to run a script once a day (at the end of the day) to process all that data and prepare a daily report. This process will take approximately an hour to run. It needs to run on a high memory instance.. From what i've read so far, I guess the best way to do it is to have a high memory spot instance run every day, set it up to execute the script on startup and and shut down when done. Is that the right way to do it? If so, how to do it? how to tell the spot instance to run every day? through a cron job on the other server or is there a better way? How to set it up to run the script on startup? through cloudinit? Any help would be appreciated. One last thing, the job is not very time sensitive as long as it runs every day.. thanks

  Read the article

• can't change wallpaper real time regedit commands

  - by itagomo

  i'm a first time 'SuperUser' poster .. what i want is to programatically change Desktop Wallpaper every few hours .. i'm using a batch file (.bat) and don't want to use other languages or programs, just the pre-installed stuffs with Windows XP .. i've already made my script that will modify values in the Registry reg add "HKCU\Control Panel\Desktop" /v Wallpaper /d "C:\Pictures\picture1.jpg" but it's not taking effect real time even with this command: RUNDLL32.EXE USER32.DLL,UpdatePerUserSystemParameters ,1 ,True need to reboot first to take effect. if i'm going to use Display Properties, it'll show at once. what i've noticed is that changes will take effect real time if it's a .bmp file and not for .jpg images. Second option is to convert JPG to 24-bit BMP files (to look exactly the same, but will triple the file size), but i'm hoping a better way .. i've already googled things but no avail.. i hope you (the helpful reader) can post any .bat or even vbs script to change Desktop Wallpaper instantly with JPG pictures .. hoping there's an answer without installing other apps or scripts ..

  Read the article

• How to "open" existing VMs in Hyper-V without importing them?

  - by Borek

  I had a PC with two physical disks: C: containing the host operating system D: containing a folder D:\VMs where all my virtual machines were stored Now, the C: disk died. I bought a new one, reinstalled Windows on it, enabled Hyper-V feature and now I just need to open the VMs from the D:\VMs folder. However, I don't seem to be able to find a menu item or anything that would allow me to do that - the only thing I see is the "import" command which unfortunately requires the VMs to be explicitly exported (my machines weren't). I firmly believe that when I have all the files constituting a VM (the VHD file, some XML files describing the settings etc.) it must be somehow possible to just "open" these existing VMs in Hyper-V, right? What command am I missing? Edit: I know I can create a blank virtual machines and then just point them to use existing VHDs. However, I am not sure about all the different settings I've made to those VMs so I hope there's a way to simply open those existing VMs instead of recreating them.

  Read the article

• Why host and vmware guests fail to get MAC of each other?

  - by Georgiy Nemtsov

  I have Windows 7 64bit host running VmWare Workstation 8 with two CentOS 6.3 guests. All guests adaptors are bridged with statically assigned ip's. Connectivity bitween host and guests was fine for many days running this setup. And today while I was working suddenly host and guests became unreachable for each other. While both host and guests could connect to internet and connect to other mashines in my networks. On guests arp -a showed for host ip address: ? (192.168.1.3) <incomlete> on eth0 On host arp -a showed for guests ip 192.168.1.19 00-00-00-00-00-00 192.168.1.20 00-00-00-00-00-00 All other arp records was OK. Deleting arp-caches didn't help neither on guests nor on host. After that I disabled and reenabled network adaptor on my Windows 7 host. And the problem was gone. arp -a now shows correct MACs on all instances. As I suppose the issue was about expiry of arp cache. For some reason host and guests couldn't get their MACs. Hope somebody knows what it is all about? I am preparing guests to work in production and don't want to face such problems in future! Also I was supprised while investigating this issue from another mashine that could connect both on guests and host. On that mashine arp -a showed same MAC for host and two guests.

  Read the article

• Windows XP VM on VMWare ESXi 4.1 "pausing" / blocked occasionally

  - by FelixD

  We have an issue with Windows XP SP3 VMs on VMWare ESXi 4.1.0 (the free version): They sometimes seem to "pause" for several minutes. This happens rarely (maybe once a month per VM, at least noticed only that often), but still is an issue for us. It happens for three different but similar VMs on three pretty different hosts (different hardware). I have the feeling that the "pausing" is not actually the CPU blocking, but probably the harddisks, but not 100% sure. The servers have one IDE disk (C:) and one SCSI (D:) and it might be either of the two. I have seen scheduled tasks simply not starting for up to 9 minutes and then running normally again with normal speed. They were totally blocked. This is not a load issue, the VMWare hosts have average load and the VMs in question already have reserved CPU resources plus high priorities for CPU and disk. The Windows boxes run mainly MySQL, Tomcat, FileZilla server, Cygwin stuff, Java + R applications, VMWare client, Elusiva Terminal Server pro, Nagios client. Not sure if this might be related with any of that software (e.g. Elusiva). Trying to debug this, there was nothing visible in Windows Event log, other logs in C:\Windows, VMWare events etc. Unfortunately the vmware.log file ends with "Log throttled". We found that we ran into 2 VMWare bugs there: The VMWare client writes lots on bogus messages in the vmware.log, which we now disabled (log level error setting) plus the bug that VMWare does not unthrottle the log (at least so far despite VM reboots). I know there is not much guidance and that may also be the reason why I so far didn't find anything related on the web or on ServerFault, but maybe some of this rings a bell with someone? Or please direct me to what more info to post. I hope that the vmware.logs get unthrottled eventually (can't easily restart the hosts at the moment). Thanks for any input!

  Read the article

• RDP with multiple monitors, display preferences get reset?

  - by Martijn Kooij

  Problem: When I connect to my pc at the office via RDP all the application windows I had previously carefully placed on either monitor 1 or 2 will be "scrambled". Either all applications show on monitor 1 and monitor 2 is empty, or they have switched 1 <- 2. Expected behaviour: When I connect I see all the application windows on exactly the same position and in the exact same size as I left them the night before. I have the exact same monitors at home as I have at work: Primary 2560x1440, Secondary 900x1440. Yesterday I tried switching the physical cables on the host machine hoping that the hardware order of the monitors was the difference. But this morning my secondary monitor was completely blank, not even the taskbar (which I had set to ONLY show on the secondary). Somewhere there must be something to help Windows understand which physical monitor is which virtual RDP monitor is which RDP "server" monitor... Are there more options than switching the cables? This one has been bothering me for a long long time now, I hope someone has a solution or workaround for me. Edit I want to use both monitors, so I have checked the "Use all monitors" setting in the RDP client. For example I leave my mail and total commander on the right monitor, and visual studio and Firefox on the left monitor. When I connect to RDP I want to see those applications on the same positions and sizes.

  Read the article

• IPTables Reroute SSH based on Connection string?

  - by senrabdet

  We are using a cloud server (Debian Squeeze) where public ports on a public IP route traffic to internal servers. We are looking for a way to use IPTables and ssh where based on some part of the ssh connection string (or something along these lines) iptables will reroute the ssh connection to the "right" internal server. This would allow us to use one common public port, and then re-route ssh connections to individual servers. So, for example we hope to do something like the following: user issues ssh connection (public key encryption) such as ssh -X -v -p xxx [email protected] but maybe adds something into the string for iptables to use iptables uses some part of that string or some means to re-route the connection to an internal server using something like iptables -t nat -A PREROUTING ! -s xxx.xxx.xxx.0/24 -m tcp -p tcp --dport $EXTPORT -j DNAT --to-destination $HOST:$INTPORT ....where $HOST is the internal ip of a server, $EXTPORT is the common public facing port and $INTPORT is the internal server port. It appears that the "string" aspect of iptables does not do what we want. We can currently route based on the IP table syntax we're using, but rely on having a separate public port for each server and are hoping to use one common public port and then re-route to specific internal servers based on some part of the ssh connection string or some other means. Any suggestions? Thanks!

  Read the article

• IIS Web Farm Framework servers are automatically set to "unavailable" even when they are healthy... And they never return to the available state!

  - by JohannesH

  I have 2 web farm configurations, one with 2 member servers and one with 3 member servers. I have health monitoring set up on both farms and the monitoring tool reports all servers as being healthy. However after a while all the servers are marked as being "Unavailable" and "Healthy" in the "Monitoring and Management" screen (in the "Servers" screen they are all listed with "Yes" in the "Ready for Load Balancing" column). Viewing the event log on both the web farm controller or any of farm servers doesn't reveal anything interesting. there are no warnings or errors in the period where the servers became unavailable. There are a couple of informational events about the worker process getting shut down due to inactivity but I don't hope this is the cause since that would mean that the farms will die during the night when the load is low. Am I missing something? EDIT: Btw, I think its very odd that the application pool shuts down on the servers since the health monitoring system is polling an aspx page on each server. Shouldn't that keep them going? EDIT2: Now I've also experienced this problem with the RTW version of Web Farm Framework 2.

  Read the article

• VMworkstation Windows 7 vm from physical partition?

  - by rich

  Hi All, i have a machine with 2 disks. my secondary drive has two partitions, one of which is a windows 7 64 boot partition. I have VM workstation and i would like to make a VM from the physical partition (described above). Ideally this would boot from the live disk, but if i can make a vmdk from the two partitions on the secondary drive that would be fine. 1 issue is the drive is 140gig raptor of which the two partitions i want are 40g and 30g partitions. the rest of the space is unallocated. So if i make a vmdk i really need it to be fixed at say 80 gig. I have converter but i don't understand how i can make the vmdk using this... specs Drive 1: this drive is a 120 SSD, running the host OS (Windows 7 64bit) - i've got 95 gigs free on this Drive 2: 140 gig raptor, partition 1 40g is also a windows 7 64bit install, partition 2 is 35 gig with program files folder on it.. sorta of needed to get the vm to work. There is 65gig unallocated on this disk. Drive 1 will host drive 2 as a VM.. my hope.

  Read the article

• Computer Turns on Briefly then right back off again.

  - by goddamnyouryan

  So yesterday I came home from work and went to turn my computer on....it turned on for about 5 seconds then promptly turned right back off again...before I ever saw anything on the screen. I tried again, same result. After several attempts, I've found that the length at which it turns on differs. After trying multiple times in a row, it only stays on for about 3 seconds. If I let it rest for a bit it sometimes will stay on for up to a minute (though it never boots, the screen stays black the whole time). I'm not sure what is causing this issue...I built this computer a little more than 2 years ago and this is the first issue I have ever had with it. I did all the usual checks: -It's not the power switch -The capacitors on the motherboard all seem to be in working order -The PSU seems to be fine as it lights up, fan spins, and will sometimes stay on for about a minute period My hope is that the thermal paste on the cpu has degraded and just needs to be re-applied. Does that seem like a reasonable assumption? I'm going to tear the thing apart and do a minimum system build when I get home, but any heads up as to what I should be looking for would be much appreciated. Any thoughts?

  Read the article

• What could cause random files being uploaded without permission?

  - by Dustin

  I have been having issues lately with a certain directory. It seems someone is placing files into it, or something of that sort, and any attempt to delete them is successful, HOWEVER they reappear over time (maybe not the exact same ones, but random files). I will provide you the information I can and several pictures of my problem: sandbox.mys4l.com/visual/files/b1.jpg Files like this have been appearing in my /visual/ folder, and I have no clue where they are coming from. sandbox.mys4l.com/visual/files/b2.jpg This is what is inside on of those weird files, it appears to be nothing problematic. sandbox.mys4l.com/visual/files/b4.jpg As you can see, in the time it took me to take the first picture, more odd files showed up. These log files are also being uploaded to this directory, and I know I didn't put them there. sandbox.mys4l.com/visual/files/b7.jpg This inside one of these mysterious .log files, I'm not sure what it's all about. These files only appear to be going into this specific area, and I'm not sure of their origin, only that they will not go away. I have done a full system scan at least twice with an up-to-date virus scan, and have looked for an unknown script which may be writing them there. Nothing has come up, so I come to you guys as I hear this is the best place to find answers. Hope this problem has a solution!

  Read the article

• Friendly Intranet Addresses

  - by Jmyster

  Relativly new to IIS. I'm attempting to set up multiple sites in my Intranet on one server. The server already has SharePoint Installed on it and has a binding *:80. So when I type //ServerName I get the home page of SharePoint. I get how that works. I set up a new site in IIS and set the Binding to *:30015. On a remote machine if I type //ServerName:30015 in a web browser, I get the new site. Awesome, working as intended. My Questions: Can/How do i set it up so that I can type //DivisionAppName or //Division.AppName and have it resolve itself to //ServerName:30015? Is this something I have to register with my Company's DNS server? I hope not, getting my corprate IT to assist is a nightmare. What I tried: I have added Bindings with the Host Name filled in with both DivisionAppName or Division.AppName and port 30015 but that doesn't seem to work.

  Read the article

• [openVPN] server & client on same machine . And multiple VPN servers

  - by HiWorld

  Hello everyone, im stucked configuring openvpn to build a multi vpn connection. like this: CLIENT - VPN1 - VPN2 - INTERNET Well, i already have and know how to done a normal sigle vpn but want to use a chain of vpns, so i explain what i have done and how i did it. ON VPN1. i have 1 openvpn instance running as server( where client connect to) and another as client connecting to VPN2 running as server. { Here comes the problem } when i connect VPN1 as client of VPN2 i cant connect to VPN1 from CLIENT, my question is HOW TO procced with this... Also have another third instance working as server to use VPN1 without chains. ON VPN2. 1 openvpn instance as server where VPN1 will connect and then forward to the NET. Im using TUN interface on configs. And iptables are on this way: VPN1 - openvpn ip server1 : 192.168.6.0 / ip as client of VPN2: 192.168.5.70 iptables -t nat -A POSTROUTING -s 192.168.6.0 -j SNAT --to-source 192.168.5.70 VPN2 - openvpn ip server2 : 192.168.5.0 iptables -t nat -A POSTROUTING -s 192.168.5.0/24 -j SNAT --to-source EXTERNAL_IP_TO_INTERNET Hope someone help me with this. thanks in advance

  Read the article

• When buying hardware, what sites do you trust for information? [closed]

  - by Matt Dawdy

  I won't ask "what laptop should I buy" since the information is likely to change very quickly. However, I am about to buy a laptop, and I honestly don't know where to begin researching this based on my needs. I am hoping that asking about specific sites that do reviews/recommendations that this will still be on topic. I read the 6 guidelines for subjective questions and believe that this question scores favorably. I'm starting a new job in a few weeks, and they want to know what specific laptop to purchase. I'd like to get the most for their money and get a machine that will not need to be replaced in a year. When looking at a site like Dell, it's hard to get a full picture of the performance of a laptop. Does it work with a docking station, and if so, what kinds of video outs are on it? Will it work well when compiling several large projects in .Net? Has anyone had any issues with the machine getting flaky when dragging it from work to home and back all the time? etc. So, if people would enter in their preferred sites they use when researching hardware, and why they prefer that site (x is great for laptop comparisons, y is great for gaming machine reviews, etc) the I hope that this can be a question with valuable answers to others than just myself.

  Read the article

• How to copy a large LVM volume (14TB) from one server to another?

  - by bruce

  I have to copy a very large LVM volume from server A to server B. Below is the filesystem of server A and server B Server A [root@AVDVD-Filer ~]# df -h Filesystem Size Used Avail Use% Mounted on /dev/mapper/vg_avdvdfiler-lv_root 16T 14T 1.5T 91% / tmpfs 3.0G 0 3.0G 0% /dev/shm /dev/cciss/c0d0p1 194M 23M 162M 13% /boot /dev/mapper/vg_avdvdfiler-test 2.3T 201M 2.1T 1% /test /dev/sr0 3.3G 3.3G 0 100% /mnt server B [root@localhost ~]# df -h Filesystem Size Used Avail Use% Mounted on /dev/mapper/VolGroup-LogVol00 20G 2.5G 16G 14% / tmpfs 3.0G 0 3.0G 0% /dev/shm /dev/cciss/c0d0p1 194M 23M 162M 13% /boot /dev/mapper/VolGroup00-LogVol00 16T 133M 15T 1% /xiangao/lv1 /dev/mapper/VolGroup00-LogVol01 4.7T 190M 4.5T 1% /xiangao/lv2 I want to copy the LVM volume /dev/mapper/vg_avdvdfiler-lv_root on server A to LVM volume /dev/mapper/VolGroup00-LogVol00 on server B. Server A and server B are in the same IP segment. In the LVM volume on server A, there is all average 500M avi wmv mp4 etc. I tried mounting /dev/mapper/vg_avdvdfiler-lv_root on server A to server B through NFS, then use cp to copy. It is clear I failed. Because the LVM volume is too big, I do not have good idea why. I hope a good solution here.

  Read the article

< Previous Page | 224 225 226 227 228 229 230 231 232 233 234 235  | Next Page >