Search Results

Search found 1164 results on 47 pages for 'broadcast'.

Page 23/47 | < Previous Page | 19 20 21 22 23 24 25 26 27 28 29 30  | Next Page >

• Atheros AR2413 wireless not working after shutdown

  - by Chandrasekhar

  I am using a Ubuntu 11.04 on an Acer aspire 3680 laptop and my wifi is not working. I followed the below commands to install the madwifi driver: sudo su apt-get install subversion cd /usr/src svn checkout http://madwifi-project.org/svn/madwifi/trunk madwifi tar cfvz madwifi.tgz cd madwifi make && make install echo "blacklist ath5k" /etc/modprobe.d/blacklist.conf echo "ath_pci" /etc/modules modprobe ath_pci sudo reboot After installation I am facing the same problem. My wifi wont work after I shutdown. Infact it didn't work after suspend but I rectified that problem by the following commands: Command 1: sudo rmmod -f ath_pci sudo rfkill unblock all sudo modprobe ath_pci along with the command SUSPEND_MODULES=ath_pci added to the /etc/pm/config.d/madwifi directory. So if I suspend and then on my laptop the wifi loads well and doesn't create a problem. But if I shutdown my laptop the wifi never loads again and eachtime I have to run a Ubuntu 9.04 live CD to load it. I did try adding the Command 1 to the /etc/rc.local directory but still it doesn't work. So my question is: What should I do in order to make my wireless work without having to run a live CD of ubuntu 9.04 everytime after shutdown? Thanks. Here are the outputs which one might need: Output 1 chandru@chandru-acer:~$ lspci 00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 1 (rev 02) 00:1c.1 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 2 (rev 02) 00:1c.2 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 3 (rev 02) 00:1d.0 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 (rev 02) 00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 02) 00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 02) 00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 02) 00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02) 00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE Controller (rev 02) 00:1f.3 SMBus: Intel Corporation N10/ICH 7 Family SMBus Controller (rev 02) 02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8038 PCI-E Fast Ethernet Controller (rev 14) 0a:03.0 Ethernet controller: Atheros Communications Inc. AR2413 802.11bg NIC (rev 01) 0a:09.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller 0a:09.2 Mass storage controller: Texas Instruments 5-in-1 Multimedia Card Reader (SD/MMC/MS/MS PRO/xD) Output 2: lsmod Module Size Used by wlan_tkip 17074 2 binfmt_misc 13213 1 parport_pc 32111 0 ppdev 12849 0 snd_hda_codec_si3054 12924 1 snd_hda_codec_realtek 255882 1 joydev 17322 0 snd_atiixp_modem 18624 0 snd_via82xx_modem 18305 0 snd_intel8x0m 18493 0 snd_ac97_codec 105614 3 snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m snd_hda_intel 24113 2 ac97_bus 12642 1 snd_ac97_codec snd_hda_codec 90901 3 snd_hda_codec_si3054,snd_hda_codec_realtek,snd_hda_intel i915 451053 3 snd_hwdep 13274 1 snd_hda_codec snd_pcm 80042 7 snd_hda_codec_si3054,snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m,snd_ac97_codec,snd_hda_intel,snd_hda_codec snd_seq_midi 13132 0 snd_rawmidi 25269 1 snd_seq_midi drm_kms_helper 40971 1 i915 snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51291 2 snd_seq_midi,snd_seq_midi_event pcmcia 39671 0 snd_timer 28659 2 snd_pcm,snd_seq snd_seq_device 14110 3 snd_seq_midi,snd_rawmidi,snd_seq drm 184164 4 i915,drm_kms_helper yenta_socket 27230 0 tifm_7xx1 12898 0 wlan_scan_sta 21945 1 ath_rate_sample 17279 1 pcmcia_rsrc 18292 1 yenta_socket psmouse 73312 0 tifm_core 15040 1 tifm_7xx1 snd 55295 18 snd_hda_codec_si3054,snd_hda_codec_realtek,snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m,snd_ac97_codec,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device serio_raw 12990 0 i2c_algo_bit 13184 1 i915 soundcore 12600 1 snd pcmcia_core 21505 3 pcmcia,yenta_socket,pcmcia_rsrc video 19112 1 i915 ath_pci 183044 0 snd_page_alloc 14073 5 snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m,snd_hda_intel,snd_pcm wlan 224640 5 wlan_tkip,wlan_scan_sta,ath_rate_sample,ath_pci ath_hal 398701 3 ath_rate_sample,ath_pci lp 13349 0 parport 36746 3 parport_pc,ppdev,lp usbhid 41704 0 hid 77084 1 usbhid sky2 49172 0 Output 3 root@chandru-acer:~# lshw -C network PCI (sysfs) *-network description: Ethernet interface product: 88E8038 PCI-E Fast Ethernet Controller vendor: Marvell Technology Group Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 14 serial: 00:16:36:fb:aa:64 capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=sky2 driverversion=1.28 firmware=N/A latency=0 link=no multicast=yes port=twisted pair resources: irq:43 memory:44000000-44003fff ioport:2000(size=256) *-network description: Wireless interface product: AR2413 802.11bg NIC vendor: Atheros Communications Inc. physical id: 3 bus info: pci@0000:0a:03.0 logical name: wifi0 version: 01 serial: 00:19:7d:d3:0c:fd width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list logical ethernet physical wireless configuration: broadcast=yes driver=ath_pci ip=192.168.1.6 latency=96 maxlatency=28 mingnt=10 multicast=yes wireless=IEEE 802.11g resources: irq:18 memory:d0000000-d000ffff Output 4 root@chandru-acer:~# lsmod | grep ath_pci ath_pci 183044 0 wlan 224640 5 wlan_tkip,wlan_scan_sta,ath_rate_sample,ath_pci ath_hal 398701 3 ath_rate_sample,ath_pci

  Read the article

• Hostapd to connect laptop to Android

  - by Kmegamind

  i am trying to set up my laptop as an access point for my Android to use WiFi, so i knew that ubuntu sets the network as Ad-Hoc which is not discoverable by android, So i tried the method explained here -which i found on many other websites- but when i run hostapd.conf this error appears : nl80211: Failed to set interface wlan0 into AP mode nl80211 driver initialization failed. ELOOP: remaining socket: sock=4 eloop_data=0x8e488f8 user_data=0x8e48ea0 handler=0x807c5e0 ELOOP: remaining socket: sock=6 eloop_data=0x8e4aca8 user_data=(nil) handler=0x8086770 this is how my hostapd.conf looks like : interface=wlan0 driver=nl80211 ssid=Any_SSID_name hw_mode=g channel=1 macaddr_acl=0 auth_algs=1 ignore_broadcast_ssid=0 wpa=2 wpa_passphrase=Any_password wpa_key_mgmt=WPA-PSK wpa_pairwise=TKIP rsn_pairwise=CCMP and this is my wireless card info : description: Wireless interface product: BCM43225 802.11b/g/n vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:05:00.0 logical name: wlan0 version: 01 serial: 78:e4:00:73:51:f1 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=brcmsmac driverversion=3.2.0-31-generic-pae firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:f0300000-f0303fff

  Read the article

• setup dhcp server - "Job failed to start"

  - by jdicarreira

  I have an eth0 and eth1, eth0 has dynamic ip and on eth1 i setup static ip: auto lo iface lo inet loopback auto eth0 iface eth0 inet dhcp auto eth1 iface eth1 inet static address 10.10.0.1 netmask 255.0.0.0 gateway 10.10.0.1 ` and then i setup the "isc-dhcp-server" with the fowling command: INTERFACES="eth1" Finally... I went to this one "dhcpd.conf", with the fowling comand: default-lease-time 650; max-lease-time 79520; option subnet-mask 255.0.0.0; option broadcast-address 10.10.0.255; option routers 10.10.0.2; subnet 10.10.0.0 netmask 255.0.0.0 { range 10.10.0.10 10.10.0.250; } When I try to "sudo /etc/init.d/isc-dhcp-server start", I get "start: Job failed to start" Anyone knows whats wrong? :/

  Read the article

• Silverlight Rough Cut Editor Real Time Highlights

  The NAB Show is an annual trade show produced by the National Association of Broadcasters. It is taking place in Las Vegas this week and you can check out Microsoft at the NAB Show 2010. It is interesting to watch the broadcast and web industry collide converge head on. With the launch of Silverlight 4 this morning one could say this week is a perfect storm. The media press releases from Microsoft are coming thick and fast. REDMOND, Wash. April 8, 2010 Microsoft Corp. today announced that...Did you know that DotNetSlackers also publishes .net articles written by top known .net Authors? We already have over 80 articles in several categories including Silverlight. Take a look: here.

  Read the article

• /etc/network/interfaces doesn't always take affect

  - by user1221444

  For some reason my eth0 does not have internet on reboot sometimes. I am using a static ip. I can ping my gateway, but I am unable to ping dns servers, or anything out of my network. It seems that when my internet does work(Usually but just restarting enough times), my /etc/resolv.conf has a nameserver in it. It is empty when I have no internet access. I believe something is overwriting my interfaces settings sometimes on boot. Any help would be appreciated. I am running Ubuntu Server 12.04 64bit /etc/network/interfaces: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 173.213.192.234 netmask 255.255.255.248 network 173.213.192.232 broadcast 173.213.192.239 gateway 173.213.192.233 dns-nameservers 8.8.8.8 auto eth1 iface eth1 inet static address 10.0.0.106 netmask 255.255.255.0 gateway 10.0.0.1

  Read the article

• Extremely slow transfer speed ubuntu -> Windows

  - by Hailwood

  I have two laptops, One is running Ubuntu 12.04 (EXT4) the other is running Windows 7 (NTFS). I am copying over 40gb of data (one file) from the Ubuntu laptop to the Windows Laptop. (Browse the shared folder on Ubuntu using Windows copy/paste) But I am getting transfer speeds topping out at ~700kb/s Surely this is not right. I am transferring via wifi on both laptops. My download speeds can reach 7-8mb/s on both laptops, so I know it is not the wifi cards or the router topping out. wlan0 Link encap:Ethernet HWaddr 84:4b:f5:db:b4:85 inet addr:192.168.1.66 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::864b:f5ff:fedb:b485/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:11941185 errors:0 dropped:0 overruns:0 frame:0 TX packets:11306693 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:10087111370 (10.0 GB) TX bytes:7843524888 (7.8 GB)

  Read the article

• Two Wifi Icons in Panel

  - by Alex

  I have the exact problem in 13.10 as this user Two Wifi indicators in panel. Here are some screenshots: Here are some screenshots from another user: http://ubuntuforums.org/showthread.php?t=2183020&p=12825563 ifconfig and iwconfig outputs $ ifconfig lo Link encap:Local Loopback inet addr:XXXXXX Mask:XXXXXXX inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:2243 errors:0 dropped:0 overruns:0 frame:0 TX packets:2243 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:209889 (209.8 KB) TX bytes:209889 (209.8 KB) wlan0 Link encap:Ethernet HWaddr XXXXXXXXX inet addr:XXXXXX Bcast:XXXXXXXX Mask:XXXXXXX inet6 addr: XXXXXXX Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5925 errors:0 dropped:0 overruns:0 frame:0 TX packets:3361 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2951818 (2.9 MB) TX bytes:630579 (630.5 KB) $ iwconfig lo no wireless extensions. wlan0 IEEE 802.11abgn ESSID:"XXXXX" Mode:Managed Frequency:2.437 GHz Access Point: XXXXXXXX Bit Rate=72.2 Mb/s Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on Link Quality=49/70 Signal level=-61 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:153 Invalid misc:472 Missed beacon:0

  Read the article

• Why do the interfaces show ipv6 address along with ipv4

  - by nixnotwin

  I have manually specified only ipv4 address for my interfaces. But all the interfaces automatically show inet6 address as well. Does it mean that ubuntu starts an ipv6 tunnel by default. If it does, isn't it dangerous, as ipv6 assigns public ips for all LAN clients. I only have a firewall on my NAT router, and my clients, who's interfaces show ipv6 address, do not have firewalls. Here is a screenshot: eth0 Link encap:Ethernet HWaddr 34:dc:47:2e:ad:13 inet6 addr: fe80::28cf:38ff:fb7b:da19/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5783 errors:0 dropped:0 overruns:0 frame:0 TX packets:6098 errors:0 dropped:0 overruns:0 carrier:1 collisions:0 txqueuelen:1000 RX bytes:2961324 (2.9 MB) TX bytes:1573757 (1.5 MB) Interrupt:46 Note: For privacy reasons I have modified the HWaddr and inet6 addr values.

  Read the article

• Mobile Multiplayer games and coping with high latency

  - by spaceOwl

  I'm currently researching regarding a design for an online (realtime) mobile multiplayer game. As such, i'm taking into consideration that latencies (lag) is going to be high (perhaps higher than PC/consoles). I'd like to know if there are ways to overcome this or minimize the issues of high latency? The model i'll be using is peer-to-peer (using Photon cloud to broadcast messages to all other players). How do i deal with a scenario where a message about a local object's state at time t will only get to other players at *t + HUGE_LAG* ?

  Read the article

• Ethernet not working on a Dell Inspiron 14z

  - by Izabela

  When I plug in a network cable, it is not recognized. The WI-FI is working properly, though. ifconfig output: lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1645 errors:0 dropped:0 overruns:0 frame:0 TX packets:1645 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:206840 (206.8 KB) TX bytes:206840 (206.8 KB) wlan0 Link encap:Ethernet HWaddr e0:06:e6:de:57:e7 inet addr:150.164.201.145 Bcast:150.164.201.255 Mask:255.255.255.0 inet6 addr: 2001:12f0:601:a921:98a2:3dd:3be8:c483/64 Scope:Global inet6 addr: 2001:12f0:601:a921:e206:e6ff:fede:57e7/64 Scope:Global inet6 addr: fe80::e206:e6ff:fede:57e7/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:23892 errors:0 dropped:0 overruns:0 frame:0 TX packets:14676 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:30123226 (30.1 MB) TX bytes:2189050 (2.1 MB)

  Read the article

• ifconfig not showing all IPs bound to the machine

  - by pankaj sharma

  I have configured multiple IP addresses on a ubuntu box, but when I run ifconfig it shows just one of them. I am able, however, to ping all other adresses assigned to this machine. /etc/network/interface contents: # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address 192.168.202.11 netmask 255.255.255.0 network 192.168.202.0 broadcast 192.168.202.255 gateway 192.168.202.1 # dns-* options are implemented by the resolvconf package, if installed dns-search idil.dz1.da auto eth0:1 iface eth0:1 inet static address 192.168.202.12 netmask 255.255.255.0 auto eth0:2 iface eth0:2 inet static address 192.168.202.13 netmask 255.255.255.0 auto eth0:3 iface eth0:3 inet static address 192.168.202.14 netmask 255.255.255.0 auto eth0:4 iface eth0:4 inet static address 192.168.202.15 netmask 255.255.255.0 auto eth0:5 iface eth0:5 inet static address 192.168.202.16 netmask 255.255.255.0 but the output of the ifconfig is only: 192.168.202.11

  Read the article

• How can a Cisco Aironet wireless card connect to a WPA encrypted network?

  - by Aibara Iduas

  I have a Thinkpad T40 running Ubuntu 10.10. I want to connect to wireless networks with WPA encryption; they appear in the network list, but are grayed out. The card does support WPA, since it works in Windows. In 10.10 the wireless works just fine with unprotected and WEP networks, but cannot connect to any WPA networks. The card is a Cisco Aironet Wireless 802.11b. I've been reading a lot of forum posts trying to find a solution, but either encounter threads where no solution was found or answers longer apply (most date from 2007, since this isn't the newest of computers). Here is the output of sudo lshw -c network: *-network:1 DISABLED description: Wireless Interface product: Cisco Aironet Wireless 802.11b vendor: AIRONET Wireless Communications physical id: 2 bus info: pci@000:02:02.0 logical name: eth1 version: 00 serial: 00:02:8a:78:6a:44 width: 32 bits clock: 33MHz capabilities: pm vpd bus_master cap_list rom ethernet physical wireless logical configuration: broadcast=yes driver=airo latency=64 maxlatency=4 mingnt=4 multicast=yes wireless=IEEE 802.11-DS Thanks, any help would be greatly appreciated!

  Read the article

• Application to organize / manage installed networks

  - by vicmp3

  I was wondering if there is a Application where you can organize networks. I mean if you have installed some networks you have to note every pc's name, his ip-address and so on. Is there a Application where you can manage it? I saw the monitoring tools but that is not exactly what I'm looking for. Maybe I didnt explain me well, after all my englis his not so good :) For example if I install many different networks I write in a book how I configured them. I write pc-name ip-address ip-gateway ip-broadcast and so on for each network. It will be great if I can do it in a program to organize it well, and for example it gives me a node view of the network.

  Read the article

• How to make audio and video streaming servers work?

  - by Santosh Linkha

  I am PHP MySQL developer and I am interested in the way television and radio are broadcasted over Internet live. I want to know how it works and and what are its requirements (which package of which programming language offers the best). And please clarify me: Websites are stored in servers. From my desktop, if I want to broadcast some video, then I need to connect to webserver (to upstream the video). Is there an application to do that (or do I have to code that or embed in my web application and which programming language would be suitable (does Python support that))? And I also need a script to handle the upstreamed video or audio (can I do that with PHP)?

  Read the article

• When Ubuntu Server restarts eth0 Doesn't come back up

  - by JoelGsus

  Every time I restart my Ubuntu Server 11.10 I can't ssh into it because ETH0 doesn't come up automatically. I never had this problem before upgrading to 11.10. I have to login to the server and start the ETH0 manually. I would appreciate it any help. Thanks. Here is my /etc/networks/interfaces file: #The loopback network interface auto lo eth0 iface lo inet loopback # The primary network interface iface eth0 inet static address 192.168.1.102 netmask 255.255.255.0 broadcast 192.168.1.255 network 192.168.1.0 gateway 192.168.1.1

  Read the article

• Ethernet not working in 12.04 (Dell Inspiron 14z)

  - by Izabela

  When I plug in a network cable, it is not recognized. The WI-FI is working properly, though. ifconfig output: lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1645 errors:0 dropped:0 overruns:0 frame:0 TX packets:1645 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:206840 (206.8 KB) TX bytes:206840 (206.8 KB) wlan0 Link encap:Ethernet HWaddr e0:06:e6:de:57:e7 inet addr:150.164.201.145 Bcast:150.164.201.255 Mask:255.255.255.0 inet6 addr: 2001:12f0:601:a921:98a2:3dd:3be8:c483/64 Scope:Global inet6 addr: 2001:12f0:601:a921:e206:e6ff:fede:57e7/64 Scope:Global inet6 addr: fe80::e206:e6ff:fede:57e7/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:23892 errors:0 dropped:0 overruns:0 frame:0 TX packets:14676 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:30123226 (30.1 MB) TX bytes:2189050 (2.1 MB)

  Read the article

• Cannot connect to ethernet port

  - by Jnir

  I'm running Ubuntu 12.04 LTE. I'm trying to connect via ethernet for the first time but have had no success. Ifconfig eth0 returns: eth0 Link encap:Ethernet HWaddr: 00:01:2e:3f:f1:a0 inet6 addr: fe80::201:2eff:fe3f:f1a0 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:68 errors:0 dropped:0 overruns:0 frame:0 TX packets:183 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:8374 (8.3 KB) TX bytes:42944 (42.9KB) Interrupt:16 Base address:0x6c00 /etc/network/interfaces has auto lo iface lo inef loopback auto eth0 iface eth0 inet dhcp sudo /etc/init.d/networking prints: * Running /etc/init.d/networking restart is deprecated because it may not enable again some interfaces * Reconfiguring network interfaces... Failed to bring up eth0 [OK]

  Read the article

• The Best Websites for Listening to Podcasts and Learning How to Create Your Own

  - by Lori Kaufman

  Podcasts, or webcasts, are shows about many different topics that are broadcast over the web and broken up into parts, or episodes.  You subscribe to podcasts and new episodes are automatically delivered to you as they are released. We’ve collected the best websites for finding many different types of webcasts and for finding resources to help you in creating and producing your own podcasts. In the coming weeks, we will be publishing other articles about the best websites for educating and entertaining yourself online, such as sites for eBooks, audiobooks, movies and TV shows, documentaries, user-made videos, free online courses, news and information, and music (downloads, streaming, and radio). How to Make Your Laptop Choose a Wired Connection Instead of Wireless HTG Explains: What Is Two-Factor Authentication and Should I Be Using It? HTG Explains: What Is Windows RT and What Does It Mean To Me?

  Read the article

• Broadcasting webinars to and from Ubuntu

  - by Chris Wilson

  I've recently attended an online workshop using Citrix GoToWebinar, a service that allows someone to broadcast their desktop and audio out to all members connected to the presentation as well as receive audio and screencasts from those attendees , and the experience was unbelievable, and I was wondering if there was any such service/software available on Ubuntu. Points to consider include, but are not limited to: Web services or local applications. Free (as in beer) or paid. Free (as in speech) or proprietary. Ease of use Ease of setup Any other point that anyone can thing of

  Read the article

• Broadcom bcm4313 Ubuntu 13.10 connection time out

  - by Wahtever

  After upgrading to Ubuntu 13.10 I keep getting connection timed out every few seconds at which point i have to disconnect and reconnect to the WiFi network. The WiFi card worked fine on 13.04 with the bcmwl-kernel-source installed but giving problems on 13.10: *-network description: Wireless interface product: BCM4313 802.11bgn Wireless Network Adapter vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth1 version: 01 serial: c0:14:3d:cc:c9:c7 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=6.30.223.141 (r415941) ip=192.168.1.4 latency=0 multicast=yes wireless=IEEE 802.11abg resources: irq:17 memory:f0500000-f0503fff How can i fix this? Thanks

  Read the article

• Writing Ubuntu shell scripts

  - by Lukesh

  Write a script that will shut down one of your server called “appsserver” every night in order to preserve power. But before the appsserver is brought down, your script should do the following: Check if there are any users logged into the appsserver Check the size of the directory /usr/tmp is bigger than 1G and delete all its content. If (a) is true, send a broadcast message to all user that the machine will shut down in 20 minutes and that they should log out of the appsserver All the output of the commands in your script should be sent to a log file with the script running date appended to the log file itself (e.g. shutdown_14_Nov_2011.log).

  Read the article

• 11.04 Wireless is disabled by hardware switch Hp Compaq nc6220

  - by user75711

  Here is some backstory if it is helpful: I had Windows Vista on my computer and I wanted to use wubi to install Ubuntu, everything was fine until I booted into the OS. It said my wireless was disabled by a Hardware Switch. So I booted back into Vista and it disabled there too. I have gotten rid of vista and installed 11.04 instead. It still has this error and as far as I know there is no switch anywhere and the fn keys do nothing. My lshw is: *-network DISABLED description: Wireless Interface product: PRO/Wireless 2915ABG [Calexico2] Network Connection vendor: Intel Corporation physical id: 4 bus info: pci@0000:02:04.0 logical name: eth1 version: 05 serial: 00:15:00:0c:5d:62 width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver-ipw2200 driverversion=1.2.2kmprq firmware=ABG:9.0.5.27 (Dec 12 2007) latency=64 link=no maxlatency=24 mingnt=3 multicast=yes wireless=IEEE 802.11abg resources: irq:21 memory:d0400000-d0400fff Thanks

  Read the article

• Forwarding data between two interfaces

  - by user84471

  I installed Ubuntu server 12.04 after that I installed dhcp3-server and configured it like this: At isc-dhcp-server INTERFACES="eth0" And in dhcpd.conf # A slightly different configuration for an internal subnet. subnet 192.168.1.0 netmask 255.255.255.0 { range 192.168.1.5 192.168.1.100; option domain-name-servers 192.168.1.1; option domain-name "nazwa.local"; option routers 192.168.1.1; option broadcast-address 192.168.1.255; default-lease-time 600; max-lease-time 7200; } Also I have two eth interfaces: # second netowrk interface auto eth0 iface eth0 inet static address 192.168.1.1 netmask 255.255.255.0 # The primary network interface auto eth1 iface eth1 inet dhcp When I plug computer to eth0 I get propertly ip adress but I can't visit any sites. I do even this: echo 1 > /proc/sys/net/ipv4/ip_forward

  Read the article

• Ubuntu 12.04 Ethernet works sporadically on lenovo x200 tablet

  - by user73100

  This is what I got from ifconfig eth0 Link encap:Ethernet HWaddr 00:1f:16:1a:0e:7e inet6 addr: fe80::21f:16ff:fe1a:e7e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:34 errors:0 dropped:0 overruns:0 frame:0 TX packets:387 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:16036 (16.0 KB) TX bytes:98315 (98.3 KB) Interrupt:20 Memory:f2700000-f2720000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:704 errors:0 dropped:0 overruns:0 frame:0 TX packets:704 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:55280 (55.2 KB) TX bytes:55280 (55.2 KB)

  Read the article

• Best video recording & mixing software for Ubuntu

  - by ???? No

  I'm searching for a quality software for recording video streams and mixing 3 cameras' streams and photos. I need it also for online streaming on a website. It could be a commercial software, doesn't have to be open source or free. I just don't have a clue if there is something like this. Thanks in advance. P.S. It's for Ubuntu 12.04 P.S.S. Maybe my definition is not correct or full, so I have to add - I need the program for live broadcast and recording on the computer at the same time.

  Read the article

< Previous Page | 19 20 21 22 23 24 25 26 27 28 29 30  | Next Page >