Search Results

Search found 13401 results on 537 pages for 'external monitor'.

Page 23/537 | < Previous Page | 19 20 21 22 23 24 25 26 27 28 29 30  | Next Page >

• external USB HD doesn't show up on 'sudo fdisk -l' on one Ubuntu, shows up on another (both 'precise')

  - by Menelaos

  I have a 1.5TB WD external USB HDD and two Ubuntu systems, both 'precise'. When I plug the disk on system A it doesn't show up on the output of sudo fdisk -l nor is it automatically mounted (note that that wasn't always the case - it used to appear in the past). When I plug it on system B (again Ubuntu precise) it shows up when I do a sudo fdisk -l (output appended at the end) and mounts automatically just fine. What does this discrepancy point to and what kind of diagnostics should I run / tools I should use to troubleshoot the problem? I followed the suggestion I received to do a sudo tail -f /var/log/syslog and the output is the following when I plug, unplug and replug the USB cable on System A: Sep 14 23:27:09 thorin mtp-probe: checking bus 2, device 3: "/sys/devices/pci0000:00/0000:00:13.2/usb2/2-2" Sep 14 23:27:09 thorin mtp-probe: bus: 2, device: 3 was not an MTP device Sep 14 23:28:01 thorin kernel: [ 338.994295] usb 2-2: USB disconnect, device number 3 Sep 14 23:28:04 thorin kernel: [ 341.808139] usb 2-2: new high-speed USB device number 4 using ehci_hcd Sep 14 23:28:04 thorin mtp-probe: checking bus 2, device 4: "/sys/devices/pci0000:00/0000:00:13.2/usb2/2-2" Sep 14 23:28:04 thorin mtp-probe: bus: 2, device: 4 was not an MTP device Sep 14 23:29:54 thorin AptDaemon: INFO: Quitting due to inactivity Sep 14 23:29:54 thorin AptDaemon: INFO: Quitting was requested (I guess the last two message are irrelevant). Output of sudo fdisk -l on System B $ sudo fdisk -l Disk /dev/sda: 1500.3 GB, 1500301910016 bytes 255 heads, 63 sectors/track, 182401 cylinders, total 2930277168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00070db4 Device Boot Start End Blocks Id System /dev/sda1 * 2048 2905114623 1452556288 83 Linux /dev/sda2 2905116670 2930276351 12579841 5 Extended /dev/sda5 2905116672 2930276351 12579840 82 Linux swap / Solaris Disk /dev/sdb: 250.1 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders, total 488397168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x9c849c84 Device Boot Start End Blocks Id System /dev/sdb1 * 63 488375999 244187968+ 7 HPFS/NTFS/exFAT Disk /dev/sdg: 1500.3 GB, 1500299395072 bytes 255 heads, 63 sectors/track, 182401 cylinders, total 2930272256 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0003e17f Device Boot Start End Blocks Id System /dev/sdg1 2048 2930272255 1465135104 7 HPFS/NTFS/exFAT

  Read the article

• Dual monitor ATI hd 4350 (1GB PCI-e), ubuntu 12.04 (pear Linux) Do I need the ATI driver or open source?

  - by Geeve

  I think I covered it in the title, Right now both monitors are mirrored (both 19" at 1440x900). I guess what I need to know is do I need the ATI proprietary driver or will the open source driver from Ubuntu (additional drivers) work? I want to expand the desktop between the two monitors. Still finishing install and running updates now, I just wanted to gather all documentation and downloads prior to doing what is necessary. Thanks Geeve

  Read the article

• Do I need the ATI driver or open source for dual monitor setup (ATI HD 4350 - 1GB PCI-e) in Pear Linux 12.04?

  - by Geeve

  I think I covered my question in the title. Right now both monitors are mirrored (both 19" at 1440x900). I guess what I need to know is do I need the ATI proprietary driver or will the open source driver from Ubuntu (additional drivers) work? I want to expand the desktop between the two monitors. Still finishing install and running updates now, I just wanted to gather all documentation and downloads prior to doing what is necessary. Any help will be greatly appreciated.

  Read the article

• External 1TB WD USB 3.0 HDD is not detecting. Working perfectly find in Windows

  - by Yathi

  My 1TB USB 3.0 was working fine earlier in Ubuntu as well as Windows. But lately it is not at all being detected in Ubuntu. It still works fine in Windows. I did update my Ubuntu to 12.10 but I am not sure if that caused the issue. When I connect my HDD and run dmesg | tail: [ 47.804676] usb 4-3: >Device not responding to set address. [ 48.008575] usb 4-3: >Device not responding to set address. [ 48.212421] usb 4-3: >device not accepting address 9, error -71 [ 48.324451] usb 4-3: >Device not responding to set address. [ 48.528340] usb 4-3: >Device not responding to set address. [ 48.732165] usb 4-3: >device not accepting address 10, error -71 [ 48.844138] usb 4-3: >Device not responding to set address. [ 49.048179] usb 4-3: >Device not responding to set address. [ 49.251881] usb 4-3: >device not accepting address 11, error -71 [ 49.251907] hub 4-0:1.0: >unable to enumerate USB device on port 3 The output of sudo fdisk -l is : Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x00030cde Device Boot Start End Blocks Id System /dev/sda1 2048 1332981759 666489856 83 Linux /dev/sda2 1332981760 1953523711 310270976 5 Extended /dev/sda5 1332983808 1349365759 8190976 82 Linux swap / Solaris /dev/sda6 1349367808 1953523711 302077952 7 HPFS/NTFS/exFAT Disk /dev/sdb: 120.0 GB, 120034123776 bytes 255 heads, 63 sectors/track, 14593 cylinders, total 234441648 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000a2519 Device Boot Start End Blocks Id System /dev/sdb1 * 2048 103368703 51683328 7 HPFS/NTFS/exFAT /dev/sdb2 103368704 154568703 25600000 83 Linux /dev/sdb3 154568704 234440703 39936000 7 HPFS/NTFS/exFAT /dev/sda and /dev/sdb are my 2 internal HDDs. But the external one which should be /dev/sdc is not even being shown though it is connected and the LED on the HDD is glowing. Someone had suggested adding blacklist uas to /etc/modprobe.d/blacklist.conf. Tried that as well. But still not working. Can someone help me out.

  Read the article

• How to tell Windows 7 "sleep when laptop is closed, unless there's an external monitor connected; then use that"?

  - by Josh

  Most of the time, I would like my Windows 7 laptop to sleep when I close it. But sometimes, I like to connect an external monitor over DVI. I would like my laptop to use the external monitor when I close the lid, but only when a monitor is connected to the DVI port. Otherwise, sleep when closed. Is there any way I can do that, without manually changing the power settings every time I decide to use the monitor?

  Read the article

• Monitor multiple variable amounts of processes' start and exit

  - by ron975

  I need some code to monitor the start and exit of processes. For example, assume I have a config file with 3 processe names, lets say, foo.exe, bar.exe and abc.exe. How I imagine this be done would be to create 3 threads and somehow listen to each process individually with a timer in each thread, and then do something afterwards. However, I would need to dynamically create threads and timers, as the config file is meant to be modifiable. I can work with VB.NET or C# Code. Thanks.

  Read the article

• How to set resolution higher than maximum shown?

  - by Olivier Lalonde

  I just bought an external monitor for my laptop (Asus VH242H) but cannot set its resolution to anything higher than 1600x900. I tried both from System/Administration/Monitors and the ATI Catalyst Control Center. There was a CD that came with the monitor but it only contains a Windows installer. According to the monitor's specifications: 23.6” 16:9 widescreen with 1920×1080 resolution enables borderless Full HD 1080p full-screen video display. My graphic card is an ATI Mobility Radeon HD 4670 and the monitor is currently connected to my laptop with a VGA cable. How can I set my external monitor to its maximum resolution?

  Read the article

• USB external drive is not recognized by any OS, how to troubleshoot in Ubuntu?

  - by Breno

  First of all I would like to inform you that I saw a question similar to mine but the error was different, so here's my problem... I have an external HD samsung s2 model of 500GB and a day to day just stopped working, tried in other systems (windows and mac) however are not recognized. In the windows device manager when I insert the usb it states that the device in question are not working properly. Well, in the logs of my ubuntu 4.12 I see the following message when I insert my usb device in: [ 2967.560216] usb 7-2: new full-speed USB device number 2 using uhci_hcd [ 2967.680182] usb 7-2: device descriptor read/64, error -71 [ 2967.904176] usb 7-2: device descriptor read/64, error -71 [ 2968.120227] usb 7-2: new full-speed USB device number 3 using uhci_hcd [ 2968.240207] usb 7-2: device descriptor read/64, error -71 [ 2968.464063] usb 7-2: device descriptor read/64, error -71 [ 2968.680087] usb 7-2: new full-speed USB device number 4 using uhci_hcd [ 2969.092085] usb 7-2: device not accepting address 4, error -71 [ 2969.208155] usb 7-2: new full-speed USB device number 5 using uhci_hcd [ 2969.624076] usb 7-2: device not accepting address 5, error -71 [ 2969.624118] hub 7-0:1.0: unable to enumerate USB device on port 2 [ 4520.240340] usb 7-1: new full-speed USB device number 6 using uhci_hcd [ 4520.364079] usb 7-1: device descriptor read/64, error -71 [ 4520.588109] usb 7-1: device descriptor read/64, error -71 [ 4520.804140] usb 7-1: new full-speed USB device number 7 using uhci_hcd [ 4520.924136] usb 7-1: device descriptor read/64, error -71 [ 4521.148083] usb 7-1: device descriptor read/64, error -71 [ 4521.364105] usb 7-1: new full-speed USB device number 8 using uhci_hcd [ 4521.776237] usb 7-1: device not accepting address 8, error -71 [ 4521.888206] usb 7-1: new full-speed USB device number 9 using uhci_hcd [ 4522.296102] usb 7-1: device not accepting address 9, error -71 [ 4522.296150] hub 7-0:1.0: unable to enumerate USB device on port 1 [ 4749.036104] usb 7-2: new full-speed USB device number 10 using uhci_hcd [ 4749.156209] usb 7-2: device descriptor read/64, error -71 [ 4749.380215] usb 7-2: device descriptor read/64, error -71 [ 4749.596206] usb 7-2: new full-speed USB device number 11 using uhci_hcd [ 4749.716409] usb 7-2: device descriptor read/64, error -71 [ 4749.940110] usb 7-2: device descriptor read/64, error -71 [ 4750.156257] usb 7-2: new full-speed USB device number 12 using uhci_hcd [ 4750.572150] usb 7-2: device not accepting address 12, error -71 [ 4750.684215] usb 7-2: new full-speed USB device number 13 using uhci_hcd [ 4751.100182] usb 7-2: device not accepting address 13, error -71 [ 4751.100224] hub 7-0:1.0: unable to enumerate USB device on port 2 Here is my system: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 002: ID 08ff:2810 AuthenTec, Inc. AES2810 00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07) 00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) 00:02.1 Display controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) 00:1a.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 02) 00:1a.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 02) 00:1a.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 02) 00:1a.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 02) 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 02) 00:1c.1 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 (rev 02) 00:1c.4 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 (rev 02) 00:1d.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 02) 00:1d.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 02) 00:1d.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 02) 00:1d.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 92) 00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev 02) 00:1f.2 IDE interface: Intel Corporation 82801IBM/IEM (ICH9M/ICH9M-E) 2 port SATA Controller [IDE mode] (rev 02) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 02) 00:1f.5 IDE interface: Intel Corporation 82801IBM/IEM (ICH9M/ICH9M-E) 2 port SATA Controller [IDE mode] (rev 02) 02:01.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev ba) 02:01.1 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller (rev 04) 02:01.2 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 21) 09:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5756ME Gigabit Ethernet PCI Express 0c:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01) Does anyone have any clue what would be the problem?

  Read the article

• Can't call animated png script from external js file

  - by Tomas

  Hello, I'm trying to put an animated PNG dinamicaly from external .js file. First I found a simple animated png solution, which draws an animation wherever you put the code within tags, but now it looks like I don't know how to call the function properly from external file. The script is from www.squaregoldfish.co.uk/software/animatedpng, and it looks something like this: <script type="text/javascript" src="animatedpng.js"></script> <div id="pnganim" align="center"> <script> fishAnim = new AnimatedPNG('fish', 't01.png', 3, 100); fishAnim.draw(false); </script> </div> Now, I'm trying to call this from external.js file and jquery: function addFish(){ $('#pnganim').html('<script type="text/javascript" src="animatedpng.js" />'); fishAnim = new AnimatedPNG('fish', 'fish01.png', 3, 100); myFish = fishAnim.draw(false); $('#pnganim').append(myFish); } ... and it's not working. After I click a button that calls the addFish function, it opens only the first frame on a blank page. What am I doing wrong here? Thanks

  Read the article

• Monitor files similar to System Internal's/Microsoft's FileMon/Process Monitor

  - by Tom1952

  I need to generate an event when a file is closed by another app. Unfortunately, ReadDirectoryChangesW doesn't report the close event. It would be possible for me to poll (with a TTimer) any file that reported by ReadDirectoryChangesW as modified, waiting for it to be closed (using CreateFile to detect this). However, what I'd prefer is a completely event driven solution. Is there a way to hook system calls and detect all file closing events? I simply want to know the path & name of any file that has just been closed.

  Read the article

• Windows Screensaver Multi Monitor Problem

  - by Bryan

  I have a simple screensaver that I've written, which has been deployed to all of our company's client PCs. As most of our PCs have dual monitors, I took care to ensure that the screensaver ran on both displays. This works fine, however on some systems, where the primary screen has been swapped (to the left monitor), the screensaver only works on the left (primary) screen. The offending code is below. Can anyone see anything I've done wrong, or a better way of handling this? For info, the context of "this", is the screensaver form itself. // Make form full screen and on top of all other forms int minY = 0; int maxY = 0; int maxX = 0; int minX = 0; foreach (Screen screen in Screen.AllScreens) { // Find the bounds of all screens attached to the system if (screen.Bounds.Left < minX) minX = screen.Bounds.Left; if (screen.Bounds.Width > maxX) maxX = screen.Bounds.Width; if (screen.Bounds.Bottom < minY) minY = screen.Bounds.Bottom; if (screen.Bounds.Height > maxY) maxY = screen.Bounds.Height; } // Set the location and size of the form, so that it // fills the bounds of all screens attached to the system Location = new Point(minX, minY); Height = maxY - minY; Width = maxX - minX; Cursor.Hide(); TopMost = true;

  Read the article

• How to disable monitor auto detection in Windows 7?

  - by Jay Yother

  I am currently running Windows 7 Ultimate 64-bit with a dual monitor setup with an NVIDIA 7950 GT graphics card. One monitor is dedicated to this machine and the other monitor is connected to a DVI KVM switch. When I switch to my other computer, Windows 7 disables the monitor. However, when I switch back it does not re-enable the monitor. The only circumstance that automatically re-enables the second monitor is when I switch back after Windows has put the monitors into power save mode. I am continually having to bring up the NVIDIA control panel to have it re-enable the monitor. Under Windows XP I would just disable the NVIDIA service to prevent it from auto-detecting the monitor (which doesn't solve the problem under Win7), and in Vista there was a registry hack that would prevent this. It looks as though that has been removed in Windows 7. I have found similar questions posted on this site, but nothing that matches my problem exactly. The following link is the question that comes the closest, but does not provide a solution to the problem. http://superuser.com/questions/96683/how-to-fix-monitor-detection-on-windows-7 Is there a way in Windows 7 to disable monitor auto-detection? Update: I just added a second graphics card to my Windows 7 64-bit machine. I plugged one monitor into each graphics card. Now, when I use the KVM switch to switch back and forth it will re-enable the second monitor like it should. There are however, a few quirks with this. If I have a program maximized on the second monitor and it has focus, when I switch it will move to monitor 1. If I have a program maximized on the second monitor and it does not have focus, when I switch it will behave like it is minimized and when I bring it back up it will show up maximized on monitor 1. Definitely better than it was, but still looking for a way to disable the auto-detection.

  Read the article

• xgamma -display parameter for dual monitor setup

  - by Shiplu

  I want to change gamma for my first monitor. Every time I invoke xgamma with different -display parameters it somehow points to my second monitor. But I want to modify first one. I tried these commands. The parameters I have used for -display are :0, :0.0, :0.1, :1.0, :1.1, :1. Only the first 2 works. But it points to my second monitor. Not the first one. Here is a shell script to test it. shiplu@KubuntuD:~$ xgamma -display :0 -> Red 1.000, Green 1.000, Blue 1.000 shiplu@KubuntuD:~$ xgamma -display :0.0 -> Red 1.000, Green 1.000, Blue 1.000 shiplu@KubuntuD:~$ xgamma -display :0.1 xgamma: unable to open display ':0.1' shiplu@KubuntuD:~$ xgamma -display :1.0 xgamma: unable to open display ':1.0' shiplu@KubuntuD:~$ xgamma -display :1.1 xgamma: unable to open display ':1.1' shiplu@KubuntuD:~$ xgamma -display :1 xgamma: unable to open display ':1' How can I change the gamma for the first/primary monitor?

  Read the article

• SQLServerCentral Webinar Series #6: Gathering and Interpreting Server Metrics including SQL Monitor

  In this webinar, MVP and noted author, Grant Fritchey shows you how to better keep track of what is happening on your instances by gathering information on performance from SQL Monitor and then using that to interpret the impact on your databases. Dec 14, 2010. NEW! SQL Monitor 2.0Monitor SQL Server Central's servers withRed Gate's new SQL Monitor.No installation required. Find out more.

  Read the article

• SQL Monitor Alerts in Outlook Without Configuring Email Settings

  - by Fatherjack

  SQL Monitor is a Red Gate tool that I have a long history with and I have worked closely with the development team from a time before it was called SQL Monitor. It is with that history in mind I am a little disappointed in myself that I have only just found out about a pretty cool feature. Out of the box SQL Monitor keeps itself to itself, it busily goes about watching over your servers, noting down when things look suspicious, change drastically or are just out and out wrong. You have to go into the settings and provide email details (SMTP server, account details etc.) before it starts getting at all intrusive with warning and alerts on the condition of your servers. However, it was after installing the most recent version that I was going through the application screen by screen looking for new and interesting changes that I noticed something that had avoided my attention. On the Alerts tab there is an option in the left hand menu. I don’t know how long ago it appeared or why I have never explored it previously but it appears that you can see your Alerts in the format of an RSS feed. Now when you click that link you are taken to a page that is the raw RSS XML – not too interesting but clearly you can use this in an RSS aggregator. Such as Outlook. Note the URL in the newly opened page take it with you into Outlook. For me it is in the form of http://SQLMonitorServerName/Alerts/Inbox/Feed. Again, this is something that I have only recently noticed – Outlook can aggregate RSS feeds. Down below the Inbox, Drafts folders etc, one up from the bottom is RSS Feeds. If you right click that and choose to Add a feed then you can supply the URL for SQL Monitor Alerts: And there you have it, your SQL Monitor Alerts available in Outlook where you can keep an eye on the number of unread items and pick them off at your convenience.

  Read the article

• SQL SERVER – 2011 – Multi-Monitor SSMS Windows

  - by pinaldave

  I have a dual screen arrangement at my home system. I love it because it’s very convenient. When I am working with SQL Server 2008 R2 or any earlier versions, I would want to use both of the Monitor so I open two separate SQL Server Management Studio and work along with it. I have no complaints with my system, at all. I am totally fine with it. However, sometimes I face small issues, like when I just want a small code open in a separate window but I do not want the windows to take over the whole of another window. But then again, I am already used to this current system. Recently when I was working with SQL Server 2011 ‘Denali’ CTP1, I dragged one of the windows by accident, and suddenly it magically appeared out of its ‘Shell’ of SSMS and was appearing on a separate monitor. I played around a bit and figured out that SSMS now supports multi-monitor (or multi screen) support with single SSMS instance. We can now drag out and drag in any window and resize them at any size. Fantastic! If you are multi-monitor user, I am sure you will like this feature. This leads me to ask you question? Do you use multi-monitor system while working with SQL Server? Leave a quick comment. Reference: Pinal Dave (http://blog.SQLAuthority.com) Filed under: Pinal Dave, PostADay, SQL, SQL Authority, SQL Query, SQL Scripts, SQL Server, SQL Server Management Studio, SQL Tips and Tricks, T SQL, Technology

  Read the article

• Laptop monitor stopped working and can't be re-enabled on a Dell Latitude E6410

  - by xektrum

  I'm using Ubuntu 12.04 (upgraded from 11.10), everything seemed to work fine until today when my laptop monitor suddenly stopped working. Here are the facts: My laptop is a Dell Latitude E6410, Intel graphics. External Monitor is attached through a docking station. Everything worked fine for about 6-7 month, then upgraded to 12.04 Issue started today after a week of upgrade. I think the issue started after I ran CounterStrike 1.6, both monitors blinked and then only the attached monitor which is connected to a docking station continued to work I thought at first that was a transient issue but then I've rebooted, removed the battery but the same happens. Laptop Monitor and external monitor work fine up to login screen, but after I login it goes black Whenever I try to re-enable laptop monitor from Display Manager I get errors: The selected configuration for displays could not be applied could not set the configuration for CRTC 63 Not sure what technical details are required but here are some: $ xrandr Screen 0: minimum 320 x 200, current 3120 x 1050, maximum 8192 x 8192 eDP1 connected (normal left inverted right x axis y axis) 1440x900 60.0 + 40.0 VGA1 disconnected (normal left inverted right x axis y axis) HDMI1 connected 1680x1050+0+0 (normal left inverted right x axis y axis) 474mm x 296mm 1680x1050 60.0*+ 1280x1024 75.0 60.0 1152x864 75.0 1024x768 75.1 60.0 800x600 75.0 60.3 640x480 75.0 60.0 720x400 70.1 DP1 disconnected (normal left inverted right x axis y axis) HDMI2 disconnected (normal left inverted right x axis y axis) DP2 disconnected (normal left inverted right x axis y axis) $ tail /var/log/Xorg.0.log [ 8367.132] (WW) intel(0): flip queue failed: Device or resource busy [ 8367.132] (WW) intel(0): Page flip failed: Device or resource busy [ 8367.174] (WW) intel(0): flip queue failed: Device or resource busy [ 8367.174] (WW) intel(0): Page flip failed: Device or resource busy [ 8367.174] (WW) intel(0): flip queue failed: Device or resource busy [ 8367.174] (WW) intel(0): Page flip failed: Device or resource busy [ 8367.265] (WW) intel(0): flip queue failed: Device or resource busy [ 8367.265] (WW) intel(0): Page flip failed: Device or resource busy [ 8367.265] (WW) intel(0): flip queue failed: Device or resource busy [ 8367.265] (WW) intel(0): Page flip failed: Device or resource busy I'm using gnome-shell, and the only ways I've been able to get both display working have been: 1) Booting with laptop disconnected from docking and then re attach external with VGA instead of DVI, but only worked for a session. 2) Removing xserver-xorg-video-intel, but then I gnome-shell is gone as well as dri I would appreciate any suggestions. Regards, ============================= WORKAROUND FOUND ============================= So I have tried few things and here is what worked: I've installed a newer version of xserver-xorg-video-intel (2.19 vs 2.17) from ppa:xorg-edgers/ppa, it didn't work at first, it was only showing low graphics mode, so I tried with a different linux-image 3.0.0-19-generic-pae instead of 3.2.0-24-generic-pae, which I believe is 12.04 precise default, then everything started to work again, Now I've installed 3.4.0-1-generic-pae from same ppa and everything goes flawless so I believe the issue is either with linux-image 3.0.0-19-generic-pae or xserver-xorg-video-intel 2.17. Hope this helps someone in the future. PS: Now xrandr shows multiple modes for my laptop monitor $ xrandr Screen 0: minimum 320 x 200, current 3120 x 1050, maximum 8192 x 8192 eDP1 connected 1440x900+1680+0 (normal left inverted right x axis y axis) 303mm x 189mm 1440x900 60.0*+ 59.9 40.0 1360x768 59.8 60.0 1152x864 60.0 1024x768 60.0 800x600 60.3 56.2 640x480 59.9 VGA1 disconnected (normal left inverted right x axis y axis) HDMI1 connected 1680x1050+0+0 (normal left inverted right x axis y axis) 474mm x 296mm 1680x1050 60.0*+ 1280x1024 75.0 60.0 1152x864 75.0 1024x768 75.1 60.0 800x600 75.0 60.3 640x480 75.0 60.0 720x400 70.1 DP1 disconnected (normal left inverted right x axis y axis) HDMI2 disconnected (normal left inverted right x axis y axis) DP2 disconnected (normal left inverted right x axis y axis)

  Read the article

• Triple monitor setup with an ATI Radeon 4200?

  - by Ben Clapp

  I have a relatively new Powerspec computer (i5 quad core processor, about a year or two old) and just grabbed a new relatively inexpensive ($40?) graphics card. It has 1 DVI, one VGA, and one HDMI output. I have two (different type) monitors plugged into the DVI and VGA slots, and they work great. However, I cannot seem to be able to get a third monitor in the HDMI slot to work. I can see the monitor (and monitor info) show up in display settings. However, if I try to switch the monitor to 'on' and click apply, nothing happens. Anyone have the slightest idea what the problem might be? (It's a Radeon graphics card FYI; if I remember right I think it was the Radeon 4200?)

  Read the article

• Connecting/Removing a Second Monitor with Multiple Workspaces

  - by Ben

  I am running 12.04 on a laptop. I use workspaces extensively to manage different projects. When I take my laptop home, I plug in an additional monitor. The problem I am having is that whenever I plug in the additional monitor, all of my windows, regardless of what workspace they were in before I connected the additional monitor, move to workspace 1. This forces me to go through all the windows and manually move the windows back to where I had them. I don't think adding a monitor to each workspace should cause windows to move around between workspaces. Any thoughts or ideas on how to fix this? Know of any workarounds? Thanks in advance!

  Read the article

• Force gdm login screen to the primary monitor

  - by Kirill

  I have two monitors attached to my video card. Primary monitor has a resolution equal to 1280x1024 and the second has 1920x1200. My gdm login screen always appears on the second monitor even if it is switched off. My question is how to force gdm to show the login screen always on the primary monitor with resolution 1280x1024? I use Nvidia GT9500 videcard in Twinview mode. I can't use Xinerama because vpdau doesn't work correclty in this mode.

  Read the article

• Change X settings to boot into laptop with non working screen using an external monitor

  - by dassouki

  My laptop committed suicide. Is there a way I can boot into my ubuntu using an external screen? Ubuntu 10.10 video: Nvidia 9500 gm i think I can get dual screen upto and until the ubuntu login screen at which point it goes back into laptop display only. Then I can just type and enter my password. The system (i assume boots into ubuntu) but I got no way of going onto the x or nvidia settings to change my display to external monitor EDIT well I booted into terminal using control shift F1 i think, and now I'm trying to reporgram x.org, but strangely it seems bland with not a lot of settings in it EDIT 2 xrandr returns "Can't open display" EDit 3 after some messing around with xrandr and xinit ... my x.org only displays one monitor instead of two in its settings although both, i.e. the laptop and external screens are both connected. EDIT 4 it seems that x.org now has a "screen" and "monitor" section, I can't seem to be able to boot linux into monitor. I get a "Monitor is not a valid keyword" in this subsection

  Read the article

• Automatically move Xubuntu panel to external monitor

  - by user1291235

  I am using xubuntu 13.04 with a dualmonitor setup. (external monitor as primary, laptop als secondary) I am using xandr to makeup my monitorsetup. However I recognized that the xubuntu panel on the top by default will always be placed on the laptop monitor. I know that i can move the panel via the panel preferences. This works. But i want to somehow either let it move automatically to the right monitor (the primary one) or to move it with a terminal command (so i can create a script which takes care of moving the panel to the primary monitor)... any ideas?

  Read the article

• Display resolution in duplicate monitor

  - by Taher

  I use duplicate one monitor laptop LCD and other monitor that monitor resolution is bigger than laptop LCD how can i set laptop LCD resolution for them? when i use mirror button it set 1024 * 768 but my laptop LCD resolution is 1366 * 768 how can i set this resolution for them? because when i set this resolution i get error. My laptop is hp dv6 6080 and vga is intel sandy bridge if i change to AMD vga can i resolve this problem?

  Read the article

• Crash on shutdown when using second monitor

  - by plua

  I have recently added a second monitor to my setup. Instead of one VGA monitor, I now have one VGA and one DVI monitor hooked up to the computer. The displays work just fine. However, ever since this monitor was added Ubuntu (10.10) does not shut down properly. I go to shutdown and it starts shutting down but just hangs and I need to manually shut it down. This has been like this for weeks and I feel not comfortable shutting it down this way over and over again. Has anybody any idea what this can be? Or, also useful, does anybody know how to get some info on why this crash occurs? Any logs that can be used for this? Thanks! Paul

  Read the article

• LCD Monitor Review: LG Flatron E2350V

  Ideal for small business computing, this wide-screen LCD monitor looks good and also does double duty as an HD video monitor.

  Read the article

< Previous Page | 19 20 21 22 23 24 25 26 27 28 29 30  | Next Page >