Search Results

Search found 3695 results on 148 pages for 'failure'.

Page 23/148 | < Previous Page | 19 20 21 22 23 24 25 26 27 28 29 30  | Next Page >

  • Windows 7 - "A disk read error occured. Press Ctrl + Alt + Del to restart"

    - by Senthil
    Problem: When I switch on my PC, after BIOS POST, a cursor is blinking for about 5 seconds and then I am getting this error message: A disk read error occurred. Press Ctrl + Alt + Del to restart. I am able to go into BIOS. But Windows loader doesn't even start. This message is shown after my motherboard logo comes and goes. Symptoms: I DID notice my system freezing for minutes at a time for past two days. Also, in the past two days, it stopped half way through the Window booting process. I had to do hard reset couple of times to get it working. But since today morning, I only get this error message. Configuration: Operating System: Windows 7 Ultimate 32-bit only. Hard disk: 1 Physical Disk - 80GB SATA Partitions: Two (2) - C: and D: File System: NTFS No drive encryption or compression is turned on. After I searched on the net, I have found people mentioning these possible causes: Hard Disk is physically failing Corrupt MBR Bad Sector I am planning to buy a new hard disk, install Windows on it and continue. But I need data from the old hard disk. The data I want is in D: drive, outside any Windows user folder, is not encrypted or compressed or protected in anyway. I think if someone/something can get the disk working again and knows NTFS, the data can be hopefully read. What steps should I follow to recover files from the defective disk? Update: I bought a new disk, installed windows on it and added the defective one as a slave. Then I was able to read the data from the defective hard disk. Though chkdsk found lots of errors, the files I wanted were not affected and I got them back :) I am not using that hard disk anymore though it seems to be working at the moment.

    Read the article

  • How can I get data off of a Corsair SSD?

    - by user1870398
    My Corsair SSD won't work and I have some critical data on it that I didn't back up (I needed to create a copy of my mechanical storage device, just forgot). The drive isn't detected by the OS or BIOS. I also tried it on another system, but all that happened was the OS failed to load (my guess was that it knew the drive was there, just couldn't read it). I tried powering it on without the data cable for a bit of time to see if it'd work again, but it didn't. Any ideas of how I can get the data off of this drive without having to send it in?

    Read the article

  • powerpoint make computer shut down on dell optiplex 760

    - by yael
    At my office we upgraded group of computers to windows 7 + office 2010, few of us have problem that when we work on powerpoint - once in a while the computer suddenly shut down (with out any message). Some of us - has no such problems. We checked and fount that the people who experience problems - use Dell Optiplex 760 PC, and everyone that have no problems use other models. We also found out that the processors of the 760's are not the same - some are Intel E7400 and one is Intel E8400, so I suspect that maybe the mother board is the problem Does any one no this problem? Does any one have an idea about it? Any help will be appreciated. Thanks, Yael

    Read the article

  • rm failing inside cron script

    - by Nicholas
    I have a cron job calling a bash script which runs fine, except for one line inside it that is suppose to remove all fines in a directory. The result of this line is always 'no such file or directory' even though I have verified (many times) that there are files in that directory. The line in question is as simply: rm /dir1/dir2/dir3/* The script works fine when run manually in the terminal, so it must be something about how the cron is run. I've tried giving 'dir3' and all the files inside it every permission possible, so it shouldn't be a permission problem. (The directory and files are also owned by the user). I've tried specifing 'SHELL=/bin/bash' inside 'crontab'. There is no sticky bit set and there is no alias on the rm command. Interestingly changing the 'rm' command to 'ls' gives the same negative result (unless you remove the trailing '*', and then that works). What am I missing here?

    Read the article

  • Acer Aspire One (mini) mfgd 9/03 locks up also when plugged in

    - by LAURIE ANN
    My problem is almost the same as the Toshiba user (Toshiba A205-5804 freezes when plugged in): Well I have a Toshiba A205-5804 and the problem is that the screen freezes anytime I plug the pc into the external power supply, not as most of the computers having the same issue, my computer DOES freeze in safe mode, and I really can't bear this problem for much longer... It's not an overheat problem, the computer is not getting hot or anything related, I've tried already to change the AC adapter, to boot only with AC and no battery, and also all of these suggestions: The only difference in my case is: I can be using the battery and when it runs down, I can just close the lid and the system goes into hibernation mode. I then plug it in and let it charge. When I think it's finally charged, I can UNPLUG it, open the lid and all is running fine on the battery again. Note: the system was NOT shut down and it still runs as long as I remove the power plug before opening the lid. I have ALL the same issues as the other Toshiba user, also. I was a tech for 9 yrs in my own business and this one has not only stumped me, but anyone I have asked has never heard of this problem. Every repair center wants to charge me for diagnosis, even is they cannot fix it. I would really like to run this system along side of my new Acer Aspire 17" laptop as I need it to finish my grad school work. Any ideas would be GREATLY appreciated. Thanx, Laurie Ann

    Read the article

  • Reinserted a RAID disk. Defined as foreign. Is import or clear the correct choice?

    - by Petrus
    I have re-inserted a RAID disk, on a DELL server with Windows Server 2008. The drive-status indicator was changing between a green and amber light, and the monitor gave the following message: There are offline or missing virtual drives with preserved cache. Please check the cables and ensure that all drives are present. Press any key to enter the configuration utility. I pressed a key and the PERC 6/I Integrated BIOS Configuration Utility showed that the RAID Status for that disk was Offline. After reinsertion of the disk the monitor is giving the following message: Foreign configuration(s) found on adapter. Press any key to continue or ‘C’ load the configuration utility, or press ‘F’ to import foreign configuration(s) and continue. After checking around on the net I am uncertain if I should choose import or clear. I cannot find out if an import means importing information from the array/system to the now foreign disk or the other way, i.e. importing information from the foreign disk to the array/system that was actually working fine. Also; if clear is a necessary thing to do ahead of a rebuild of that disk, or if clear means to clear the system to somehow make it ready to import the information from the foreign disk to the array/system, which is not what I want. I imagine that making the wrong choice here might be fatal. Please help clearing this out by telling what to choose and why.

    Read the article

  • Windows 7 remains powered on when restarting

    - by BombDefused
    I'm running windows 7 x64 on an MSI P67A-GD53 motherboard, in an Antec P280 Super Midi Towercase with a Corsair 650w PSU. I've just installed a second instance of windows 7 x64 on a separate disk (this is to keep my games separate from my work OS). The problem is that it appears now that I cannot restart from either instance of Windows 7. The shut down command, and sleep commands work as expected. When I try to restart, the shutdown happens but the system never reboots. Everything remains powered on, until I hold down the power button to force the power off. Ithink (but am not 100% sure) this has only started since I installed the second OS, and am assuming this has something to do with the motherboard needing to know which OS to run up again? Some other forums I've read suggest that the PSU has a major role in restart and could be at fault. Changing the boot order of the disks in the BIOS does not change anything. Any suggestions greatfully recieved! Update: I now have a reproduceable issue: I think the secondary OS install may have been a red herring. It was when windows tried to reboot during the install that I noticed the issue. After playing around with installing drivers, and rebooting many many times, I have found that it is the OC genie setting on the MSI motherboard that seems to trigger the problem. This makes sense as I only started using the OC genie feature a couple of weeks ago, and probably hadn't used restart in that time. However... simply turning off OC genie does not make the issue go away. I have to turn off OC genie, shutdown, start enter bios, go to the "Save and Exit" menu "Restore Defaults" yes to "Load optimized defaults", which will reset to clear the problem. Now when the PC boots into windows, I can restart as normal (and from the OS on either HDD). I only know how to control the issue, and don't still know the root cause. I'd like to be able to use the OC genie function if anyone can suggest a why I'm seeing this problem. Could it be that I'm drawing too much power when using OC feature?

    Read the article

  • Linksys WAP54G v3.1 no access, power and link LED solid

    - by user142113
    I'm managing the Network of a small enterprise. A Linksys WAP54G v3.1 used to provide the WiFi network. I was called, because the device did not provide a WiFi network anymore. I first of all tried to ping the device via LAN, but there was no reaction. I've frequently reconnected the AP to the mains and always the POWER and the LINK LED keep solid, even if no network cable is connected. What I've done yet: Reset as documented: Pressed the RESET button for 10 seconds. After that I have tried to access the AP with a direct cable connection to my computer, that I've set to a static ip of 192.168.1.240, but i got no ping response on the default IP 192.168.1.245. Furthermore ipconfig reports "media disconnected". More complex reset method as described here http://bruceshankle.blogspot.de/2005/12/how-to-reset-linksys-wap54g.html as well had no effect. also tried to ping 192.168.1.1 without success Tried this method: http://www.daniweb.com/hardware-and-software/networking/threads/142437/linksys-wireless-access-point-problem#post680245 but there was no ping response when powering up. As well the tftp transfer timed out Finally tried to short pin 15 and 16 of the flash chip on the bottom side of the AP mainboard while booting to provoke a Checksum error. This should lead to the possibility to upload a firmware with tftp, as the AP stops booting and waits for a tftp connection on 192.168.1.1. But I've had no success. As well i've put pin 15 and 16 to ground while booting, also without an effect. After all that I still can't ping the AP, ipconfig still tells me "media disconnected". The POWER and LINK LED are solid. I would appreciate your answers

    Read the article

  • Recover an HP recovery partition

    - by eric.chartier
    I have a (semi)-dead hard drive with an HP recovery partition on it. My goal is to Buy a new hard drive Copy the recovery partition to a drive ( dd if=/dev/sdb1 of=~/recovery.bak ) Make a new partition of 12000 mb with Windows 7 Copy back recovery partition to the new drive ( dd if=~/recovery.bak of=/dev/sdb1 ) Then press F11 when the laptop boots. However, this doesn't work. Any idea why? Edit: I suspect the F11 doesn't work because the laptop tries to boot the laptop, because my partition is the primary partition of the drive. Does anyone have any experience dealing with stuff like this?

    Read the article

  • USB wiped itself but still showing that its full?

    - by Brian Takan
    My Data saved from laptop to usb, and then I pulled it out, then something popped up on the screen saying that it was full and that I needed to delete stuff, so I put the USB back in and went to computer and all to go into it and when I did it isn't showing anything on the usb but when I go to computer it still shows that the usb is full. Does anybody know what is going on ? How can I get my data again?

    Read the article

  • Problem adding second domain controller to SBS 2008

    - by Quango
    Have an SBS 2008 server in one location, and want to add a backup domain controller at a different site. The two sites are linked by a VPN. New server is running Server 2008 R2, fully patched. At present it is a member server and the DNS is pointing at the SBS DNS. When I try running DCPROMO to connect the server, the wizard runs fine up to the point where the wizard is 'configuring Active Directory Domain Services' and 'examining forest': "The operation failed because: The wizard could not read operational attributes from the remote Active Directory Domain Controller SERVER.DOMAIN.LOCAL using LDAP. "The specified server cannot perform the requested operation." This error can occur if you have not been granted necessary permissions to read data in the directory. For more information, please see article 936241 in the Microsoft Knowledge Base (http://go.microsoft.com/fwlink/?LinkId=88420)." I was logged on as domain administrator. Interestingly the link is invalid and the KB article does not exist..! Settings: Configure this server as an additional Active Directory domain controller for the domain "[domain]". Site: [site] Additional Options: Read-only domain controller: "No" Global catalog: Yes DNS Server: Yes Update DNS Delegation: No Source domain controller: any writable domain controller Database folder: C:\Windows\NTDS Log file folder: C:\Windows\NTDS SYSVOL folder: C:\Windows\SYSVOL The DNS Server service will be configured on this computer. This computer will be configured to use this DNS server as its preferred DNS server.

    Read the article

  • No space left on device with encrypted disk that takes all space

    - by Yosef
    I use Ubuntu 11.04. There's no space left on device. I have encrypted the disk that takes up space (maybe it's good to disable it, but I don't know how). In shell, I get this message: No space left on device I run df -I: Filesystem Inodes IUsed IFree IUse% Mounted on /dev/sda1 3055616 602499 2453117 20% / none 210161 890 209271 1% /dev none 214789 8 214781 1% /dev/shm none 214789 53 214736 1% /var/run none 214789 3 214786 1% /var/lock /home/myuser/.Private 3055616 602499 2453117 20% /home/myuser df -I Edit: When I run only df: Filesystem 1K-blocks Used Available Use% Mounted on /dev/sda1 48060296 45618928 0 100% / none 1538340 684 1537656 1% /dev none 1547596 808 1546788 1% /dev/shm none 1547596 104 1547492 1% /var/run none 1547596 0 1547596 0% /var/lock /home/myuser/.Private 48060296 45618928 0 100% /home/myuser Edit: I thinking about few solution but I don't know which better and how exactly to do them: to enlarge partition size (I cant install gparted - no more disk space) remove encryption of partition - I really not need that

    Read the article

  • Mainboard shuts itself off after half a second or so

    - by heishe
    Here's the problem: When I start the PC, the mainboard powers up, then stays that way maybe 0.2-0.5 seconds, and then shuts off again. I say mainboard, and not PC, because I removed all the parts from the system and disconnected everything but the mainboard power supply (the broad 12 pin thingy). When I have the other parts (cpu, graphics card, ram, etc.) installed and connected, the basic behaviour stays the same, but now the mainboard runs for about 6 or 7 seconds (this is a guess) before shutting off. This all started when my monitor wouldn't receive a video signal today, without giving POSTs, so I took the graphics card and the RAM out to see if it changes anything. It didn't, except that from that point on the mainboard would start to have this behavior where it just stays on for a very short time and then shuts off again. I already tested it with a backup PSU - same behavior. What could this be? I'm thinking it can't be on a physical level (transistors burned through or something like that), since then the mainboard either shouldn't start at all or it should detect hardware failures in non-essential parts of the syste and start beeping. Sorry, I forgot to mention. It's an MSI P67A-C43. I already checked the capacitors if someone popped, but I can't find anything. I also tried resetting the cmos, but that didn't change anything.

    Read the article

  • "Reboot and select proper boot device"?

    - by overtherainbow
    Hello I didn't find the answer in Clonezilla's site/mailing list archives. Maybe someone has already seen this issue and knows how to recover from it: On a test host, using www.partedmagic.com, I created two partitions: One to hold an OS I wish to use for testing (/sda1), and a second partition to hold images (/sda2) After trying out Windows7, I used CloneZilla to restore an XPSP3 image, but I get the following error message when rebooting: "Reboot and select proper boot device" Could it be that Clonezilla didn't save/restore the MBR? Gparted didn't let me set a partition as "active", so it could also be this, but I have no idea. Thank you for any help.

    Read the article

  • System shuts down immediately after few sconds

    - by Anil
    I have a computer with following specification and was working fine after re-installing the system and refitting sink fan unit. Recently it shuts down automatically after a few seconds. I checked PSU by shorting pin no.s 13 & 14 as well as 14 & 15. It worked well means the PSU fan moves. But I never checked the voltages at different wires. I refitted the heat sink fan by applying thermal paste. but it behaved the same. Again I refitted the Heat Sink Fan, then it worked for 2 minutes and again shut down. Now it shuts down immediately after switching on. Mother board : M26GTM-3VP CPU : AMD athlon PSU : 450 watt Can anyone help?

    Read the article

  • XFS and loss of data when power goes down

    - by culebrón
    Each time electricity goes down, my desktop (without UPS) loses some temporary information. Opera can lose settings, history, cache, or mail accounts (Thanks heavens I was wise to use IMAP). Partially or all together. a whole file (complete and save) in Geany appeared empty (and I didn't commit it to Git) rhythmbox lost all podcasts subscription data I'm afraid there are other losses I just didn't see. What's the reason? A memory files cache, a mem-disk? Or non-atomic file writes in xfs? I have Ubuntu 9.10 and XFS on both / and /home partitions. Is ext4 safer in such circumstances? I've seen ext3 is faster. Is it as safe as *4? Given that the apartment I rent is connected to a common bus and 1 safety switch for several apartments, and the neighbors - alone or together - overload it at least once every week, the lights go down often enough for this to be an issue.

    Read the article

  • How to diagnose computer lockup/freezing problem

    - by Scott Mitchell
    I built a desktop computer a couple years back with the following specs: CPU: Intel Core 2 Quad Q9300 Yorkfield 2.5GHz 6MB L2 Cache LGA 775 95W Quad-Core Processor BX80580Q9300 Motherboard: EVGA 122-CK-NF68-T1 LGA 775 NVIDIA nForce 680i SLI ATX Intel Motherboard Video Card: Two EVGA 256-P2-N758-TR GeForce 8600GT SCC 256MB 128-bit GDDR3 PCI Express x16 SLI Supported Video Card PSU: SeaSonic S12 Energy Plus SS-550HT 550W ATX12V V2.3 / EPS12V V2.91 SLI Certified CrossFire Ready 80 PLUS Certified Active PFC Power Supply Memory: Two G.SKILL 4GB (2 x 2GB) 240-Pin DDR2 SDRAM DDR2 800 (PC2 6400) Dual Channel Kit Desktop Memory Model F2-6400CL5D-4GBPQ Since its inception, the machine has periodically locked up, the regularlity having varied over the years from once a day to once a month. Typically, lockups happen once every few days. By "lockup" I mean my computer just freezes. The screen locks up, I can't move the mouse. Hitting keys on my keyboard that normally turn LEDs on or off on the keyboard (such as Caps Lock) no longer turn the LEDs on or off. If there was music playing at the time of the lockup, noise keeps coming out of the speakers, but it's just the current frequency/note that plays indefinitely. There is no BSOD. When such a lockup occurs I have to do a hard reboot by either turning off the computer or hitting the reset button. I have the most recent version of the NVIDIA hardware drivers, and update them semi-regularly, but that hasn't seemed to help. I am currently using Windows 7 x64, but was previously using Windows Server 2003 x64 and having the same lockup issues. My guess is that it's somehow video driver or motherboard related, but I don't know how to go about diagnosing this problem to narrow down which of the two is the culprit. Additional information re: cooling Regarding cooling... I've not installed any after-market cooling systems aside from two regular fans I scavenged from an older computer. The fan atop the CPU is the one that shipped with it. One of the two scavenged fans I added it located at the bottom tower of the corner, in an attempt to create some airflow from front to back. The second fan is pointed directly at the two video cards. SpeedFan installation and readings Per studiohack's suggestion, I installed SpeedFan, which provided the following temperature readings: GPU: 63C GPU: 65C System: 76C CPU: 64C AUX: 36C Core 0: 78C Core 1: 76C Core 2: 79C Core 3: 79C Update #3: Another Lockup :-( Well, I had another lockup last night. :-( SpeedFan reported the CPU temp at 38 C when it happened, and there was no spike in temperature leading up to the freeze. One thing I notice is that the freeze seems more likely to happen if I am watching a video. In fact, of the last 5 freezes over the past month, 4 of them have been while watching a video on Flickr. Not necessarily the same video, but a video nevertheless. I don't know if this is just coincidence or if it means anything. (As an aside, each night before bedtime my 2 year old daughter sits on my lap and watches some home videos on Flickr and, in the last month, has learned the phrase, "Uh oh, computer broke.") Update #4: MemTest86 and 3DMark06 Test Results: Per suggestions in the comments, I ran the MemTest86 overnight and it cycled through the 8 GB of memory 5 times without error. I also ran the 3DMark06 test without a problem (see my scores at http://3dmark.com/3dm06/15163549). So... what now? :-) Any further suggestions on what to check? Is there some way to get a stack trace or something when the computer locks like that? Thanks

    Read the article

  • Mecer laptop gives me a white screen when I close the screen

    - by Dane Rossenrode
    I'm having a very strange hardware issue with my Mecer m770u laptop with intel i7 quad core, etc... I'm wondering if anyone has had this issue with any other brand/model of laptop, and what I should fix/replace to solve it...? Basically when I close the screen of the laptop, the screen often goes completely white. If I open it slowly and smoothly again, the screen returns to normal. But if I close the screen when the computer is off, and then switch it on, it boots with a white screen, and opening it slowly/smoothly doesn't help. I have to then switch it on and off a few times before it returns to normal. Makes travelling with my laptop really difficult! Any suggestions?

    Read the article

  • Freezing of computer while watching flash videos (contd)

    - by t3st
    I have asked this similar question Computer freezing while watching Flash videos from net two week before. As i mentioned in my previous problem my computer freezes while watching online videos showing 100% cpu usage. I have tried the suggestions given in that query and I have formated my whole computer and installed windows and other softwares (with latest updates) but the problem still presisting. If i watch a video online approximately after one hour my system shows very high cpu usage and when i close my browser cpu usage comes to normal(i tried to watch Cybergeddon but my computer is freezing from start,and also other youtube videos). Can you tell me whether its an hardware problem? if yes can you give any possible explanation( eg:motherboard problem,over heating etc) because i want to tell those reasons to my computer mechanic.

    Read the article

  • 2 SAN disks failing during the same overnight period

    - by Carl
    We have 2 HP Lefthand SAN servers in separate data rooms. Last week each of the SANs had 1 hard disk fail. They were in different positions on the SANs. Both data rooms are very well protected from power issues with UPS. Any ideas of what could have influenced this? Thanks, Carl

    Read the article

  • Can a virus corrupt a hard disk?

    - by sundar
    Shorter version: Hard disk corrupt, vendor claims warranty does not apply since it was "due to a virus" and "problems due to software are not covered under the warranty". Longer version: My Dell laptop recently refused to boot, and all attempts to 'repair' the Vista installation using the provided installation CD failed. I called up Dell support, and a representative took the laptop and after a day said the hard disk is corrupt. When I tried to ask for a replacement under the warranty, an official replied that the corruption was due to a virus, and "problems due to software are not covered under the warranty". Now, I get a doubt that he's trying to avoid having to provide it under the warranty. Is it possible for a hard disk to get corrupt due to a virus? If yes, is there any way we can detect it was due to a virus (as he claims to have detected)?

    Read the article

  • Webcam becomes "Unknown Device" after Windows Messenger 2011 is installed

    - by Boris
    I have Sony VAIO VGN-NS290J laptop. I installed Windows 7 Ultimate 64-bit. I was able to find drivers for all hardware without any problems. Recently, I installed Microsoft Windows Live Essentials 2011, i.e. Windows Live Messenger 2011. Ever since that application is running on my computer, my webcam is not recognized by the OS any more. It is listed as the "Unknown Device" and placed in the Universal Serial Bus controllers group in the Device Manager. There don't seem to be any drivers for this webcam. It's a standard Sony Motion Eye web camera and Sony does not offer any drivers for it. There is one application to download that utilizes the camera, but there are no drivers (and the system is showing the same behavior regardless of the presence of the application). It happens from time to time that the webcam becomes recognized by the OS again, after a couple of restarts; but not always. Then it becomes unknown again. I am absolutely positive that this issue is caused by the Windows Live Messenger 2011, because same symptoms caused the same effects before. I wish to be able to continue to use this software, but also to use my webcam. I was wondering if anyone had a similar issue and if there is a way to fix it. Thanks for all the help, I appreciate it. Update: I have discovered a pattern - if the camera goes astray, restarting the machine does not bring it back; but switching the computer off and turning it back on does. Every time! This is getting super complicated :)

    Read the article

  • Chipset fan on the frtiz - compressed air hasn't fixed anything - is there anything I can do?

    - by Anthony
    Yesterday, my computer started to make an annoying whining noise. Knowing that this is likely a fan issue, I opened the case and proceeded to determine which fan was causing the issue. I got some compressed air and tried cleaning out the dust around it (and the rest of the computer while I was at it). This hasn't seemed to fix the issue. Now, if it were just any fan, I would probably just replace the fan - they're relatively cheap after all. However, this is a special fan. Aside: For what its worth, I feel bad that the graphics card blocks part of the fan, but it is the only slot the graphics card fits, so I had no choice. After pulling out my motherboard user guide, it looks like this is a fan placed directly on top of the chipset. To be perfectly honest, I have no clue what the purpose of the chipset is - but it sounds important. After some quick research, I see that it is responsible for providing the bridge between my CPU, RAM and graphics, among other things. Just a quick search at Newegg tells me that chipset fans can be purchased at pretty reasonable prices (< 20 dollars). Is it practical to replace this fan? It is an old computer as computers go and I wouldn't be terribly upset to upgrade the motherboard and processor, so perhaps this is a sign. Hardware Specs: Motherboard: Asus A8N-E Chipset: NVIDIA nForce4 Ultra

    Read the article

  • How to Diagnose a Pre-Operating System Load or Hardware Issue

    - by soandos
    How can I find out if my problem is hardware based? If it is, how can I figure out what component is to blame How can I fix other pre-operating system issues? As an aside, what are all of these components responsible for, and if they break, what can go wrong? (This question comes up frequently, and the suggested solutions are usually the same. This community wiki is an attempt to serve as the definitive, most comprehensive answer possible. Feel free to add your contributions via edits.)

    Read the article

< Previous Page | 19 20 21 22 23 24 25 26 27 28 29 30  | Next Page >