Search Results

Search found 2840 results on 114 pages for 'ports'.

Page 23/114 | < Previous Page | 19 20 21 22 23 24 25 26 27 28 29 30  | Next Page >

• Configure firewall (Shorewall/UFW) to allow traffic for services on an Ubuntu Server

  - by Niklas

  I have an Ubuntu Server 11.04 x64 which I want to secure. The server will be open to Internet and I want to be able to SSH/SFTP into the machine and the SSH-server runs on a custom set port. I also want a web server accessible from the Internet. These tasks seems not to hard to perform but I also want SAMBA-shares to be accessible from within the local network and this seems to be a bit trickier. If possible I also want to be able to "stealth" the ports necessary to protect the server further but also allow the SAMBA-shares to be automatically found within the local network. I've never configured firewalls before except for a router and I always bump into a bunch of problem when doing it all by myself so I was hoping for some tips or preferably a guide on how to this. Thank you! Update: On second thought I'd could just as likely go with UFW if the same settings are achievable ("stealth" ports).

  Read the article

• How can I determine which GPU card is running at PCI Express 2.0 x16 & which is using x8?

  - by M. Tibbits

  Is there a way to determine the speed of the PCI Express connection to a specific card? I have three cards plugged in: two Nvidia GTX 480's (one at x16 & and one at x8) one Nvidia GTX 460 running at x8 Is there some way, either by a function call in C or an option to lspci that I can determine the bus speed of the graphics cards? When I only use one of the cards for my CUDA program, I'd like to use the one which is running at x16. Thanks! Note: lspci -vvv dumps out For the two GTX 480s. I don't see any differences that pertain to bus speed. 03:00.0 VGA compatible controller: nVidia Corporation Device 06c0 (rev a3) Subsystem: eVga.com. Corp. Device 1480 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at d4000000 (32-bit, non-prefetchable) [size=32M] Region 1: Memory at b0000000 (64-bit, prefetchable) [size=128M] Region 3: Memory at bc000000 (64-bit, prefetchable) [size=64M] Region 5: I/O ports at df00 [disabled] [size=128] [virtual] Expansion ROM at b8000000 [disabled] [size=512K] Capabilities: <access denied> Kernel driver in use: nvidia Kernel modules: nvidia, nvidiafb, nouveau 03:00.1 Audio device: nVidia Corporation Device 0be5 (rev a1) Subsystem: eVga.com. Corp. Device 1480 Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin B routed to IRQ 5 Region 0: [virtual] Memory at d7ffc000 (32-bit, non-prefetchable) [disabled] [size=16K] Capabilities: <access denied> 04:00.0 VGA compatible controller: nVidia Corporation Device 06c0 (rev a3) Subsystem: eVga.com. Corp. Device 1480 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at dc000000 (32-bit, non-prefetchable) [size=32M] Region 1: Memory at c0000000 (64-bit, prefetchable) [size=128M] Region 3: Memory at cc000000 (64-bit, prefetchable) [size=64M] Region 5: I/O ports at cf00 [size=128] [virtual] Expansion ROM at c8000000 [disabled] [size=512K] Capabilities: <access denied> Kernel driver in use: nvidia Kernel modules: nvidia, nvidiafb, nouveau 04:00.1 Audio device: nVidia Corporation Device 0be5 (rev a1) Subsystem: eVga.com. Corp. Device 1480 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin B routed to IRQ 5 Region 0: Memory at dfffc000 (32-bit, non-prefetchable) [size=16K] Capabilities: <access denied> And the only differences I see relate specifically to the memory mapping: myComputer:~> diff card1 card2 3c3 < Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- --- > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- 7,11c7,11 < Region 0: Memory at d4000000 (32-bit, non-prefetchable) [size=32M] < Region 1: Memory at b0000000 (64-bit, prefetchable) [size=128M] < Region 3: Memory at bc000000 (64-bit, prefetchable) [size=64M] < Region 5: I/O ports at df00 [disabled] [size=128] < [virtual] Expansion ROM at b8000000 [disabled] [size=512K] --- > Region 0: Memory at dc000000 (32-bit, non-prefetchable) [size=32M] > Region 1: Memory at c0000000 (64-bit, prefetchable) [size=128M] > Region 3: Memory at cc000000 (64-bit, prefetchable) [size=64M] > Region 5: I/O ports at cf00 [size=128] > [virtual] Expansion ROM at c8000000 [disabled] [size=512K] 18c18 < Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- --- > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- 19a20 > Latency: 0, Cache Line Size: 64 bytes 21c22 < Region 0: [virtual] Memory at d7ffc000 (32-bit, non-prefetchable) [disabled] [size=16K] --- > Region 0: Memory at dfffc000 (32-bit, non-prefetchable) [size=16K]

  Read the article

• AutoVue 20.2.1 for Agile Released

  - by Angus Graham

  Oracle's AutoVue 20.2.1 for Agile PLM is now available on Oracle's Software Delivery Cloud.  This latest release allows Agile PLM customers to take advantage of new AutoVue 20.2.1 features in the following Agile PLM environments:  9.3.x, 9.2.2.x, 9.2.1.x. AutoVue 20.2.1 delivers improvements in the following areas: New Format Support: AutoVue 20.2 adds support for the latest versions of popular file formats including: 2D CAD: AutoCAD 2013 MCAD: Inventor 2013, AutoCAD Mechanical 2013, Unigraphics NX8, JT 9.2 through 9.5, CATIA v5-6 R2012, Creo Parametric 2.0 ECAD: Altium Designer New Platform Support:  Client and server support has been extended to the following platforms: Java 7 JVM Google Chrome Browser Oracle VM 2 virtualization environment Installer Improvements: Ensures ports used by AutoVue are not in use - if they are, the admin will be prompted to select alternate ports. Click here to access the latest AutoVue Format Support Sheet.

  Read the article

• Plugging two external screens to laptop via VGA and HDMI

  - by avilella

  I have an Asus U30JC laptop with a VGA and HDMI ports. I can connect my external screen (1920x1200) to either of those ports but I wonder if I would be able to use two screens at the same time, one plugged to the VGA and the other to the HDMI socket. Any ideas? Where should I find out? Doing xrandr, I get: Screen 0: minimum 320 x 200, current 1366 x 768, maximum 8192 x 8192 LVDS1 connected 1366x768+0+0 (normal left inverted right x axis y axis) 293mm x 164mm 1366x768 60.0*+ 1360x768 59.8 60.0 1024x768 60.0 800x600 60.3 56.2 640x480 59.9 VGA1 disconnected (normal left inverted right x axis y axis) HDMI1 disconnected (normal left inverted right x axis y axis) DP1 disconnected (normal left inverted right x axis y axis)

  Read the article

• iptables allow dyndns domain name and auto update rules

  - by user3215

  I have registered with dyndns domain for my dynamically changing public ip address to use with iptable rules. On a server I've allowed some ports for this domain in the iptables configuration like the below entries: -A INPUT -s mycompany.dyndns.com -p tcp -m tcp --dport 22 -j ACCEPT -A INPUT -s mycompany.dyndns.com -p tcp -m tcp --dport 3306 -j ACCEPT -A INPUT -s mycompany.dyndns.com -p tcp -m tcp --dport 21 -j ACCEPT But when ever my modem restarts, I couldn't connect to these allowed ports as public ip changes with modem restart and are not updated in the iptables on the server. Is there any option to automatically update iptable rules on server.

  Read the article

• DVC101 Video Capture Device on USB hub - Ubuntu Server 12.04

  - by John

  I have a Dell Inspiron 8600 laptop I use as a media server/video capture system. It only has 2 USB ports and I have a total of 3 devices I need to connect. The DVC101 works perfectly while plugged directly into the USB port in back of the laptop. Unfortunately it does not get recognized when plugged into a passive or powered USB hub. Questions: Is there something I am missing on the Ubuntu side? Something I need to do that will allow the device to be recognized through the hub? If not, will the extra USB ports on a dell laptop dock (port replicator) act the same as the aftermarket hubs? I know this one is off topic of Ubuntu but any input appreciated.

  Read the article

• Set up Trendnet TEW-638APB Access point on Ubuntu 14.04

  - by Mr. Smileys

  I have a computer running Ubuntu 14.04, it has 2 Ethernet ports. I would like to set up this computer so that the internet comes in on one of the ports and is then shared through the other port with the Trendnet wireless access point that my other devices would connect to and use the internet. I have looked online for information on setting this up but have not been able to find anything. If someone could point me to a guide that would help me or just tell me how to do this in an answer I would really appreciate it. please help me to solve this problem

  Read the article

• Configuring SQL Server Express Edition for remote access

  - by rohancragg

  Originally posted on: http://geekswithblogs.net/rohancragg/archive/2013/07/24/configuring-sql-server-express-edition-for-remote-access.aspxI wanted to access SQL Express on my local machine from within a Client Hyper=V virtual machine on the same Domain. This article got me most of the way there: http://akawn.com/blog/2012/01/configuring-sql-server-2008-r2-express-edition-for-remote-access/ But it was a bit out of date. My steps were: Enable TCP/IP Protocol in SNAC Restart SQL Server Configure (Windows 8) Firewall to allow all Inbound for sqlservr.exe Footnote: I thought this might be relevant (nice to be able to script it): http://support.microsoft.com/kb/968872/en-us But the problem is that this is for fixed ports and not compatible with the (default) Dynamic Ports settings above.

  Read the article

• SSH not working from outside network

  - by alexander7567

  Ok.. First off my ISP does not block ports. I run web server just fine from another machine. I have port forwarded port 22. I can access within network but not out of.. I.E. my android. I get "The Operation Timed Out" on ConnectBot. Oh and I have allowed 22 on UFW. To answer what exactly happened was my ISP blocks port 22, even though a while back they told me they do not block any ports.. I changed it to port 27 and it worked without a problem.

  Read the article

• Unable to connect with IIS7 Manager to remote site

  - by saifkhan

  I was unable to connect with IIS7 manager to a remote site. I got on the phone with the hosting provider and they started troubleshooting. After a few minutes they went over all my settings, username, password...the whole shebang and I still couldn't. I then asked the support tech if any ports needed to be opened on my side and she said "ONLY PORT 80 NEEDS TO BE OPENED"... after a few more mins I decided to hop over to the IIS7 website but still couldn't find anything incicating specific ports, but I did came across a doc mentioning 8172 as a port IIS7 uses so I went to my firewall did the following OPEN PORT 8172 OUTBOUND That did the trick!...and the support tech updated her document accordingly.

  Read the article

• How to open a server port outside of an OpenVPN tunnel with a pf firewall on OSX (BSD)

  - by Timbo

  I have a Mac mini that I use as a media server running XBMC and serves media from my NAS to my stereo and TV (which has been color calibrated with a Spyder3Express, happy). The Mac runs OSX 10.8.2 and the internet connection is tunneled for general privacy over OpenVPN through Tunnelblick. I believe my anonymous VPN provider pushes "redirect_gateway" to OpenVPN/Tunnelblick because when on it effectively tunnels all non-LAN traffic in- and outbound. As an unwanted side effect that also opens the boxes server ports unprotected to the outside world and bypasses my firewall-router (Netgear SRX5308). I have run nmap from outside the LAN on the VPN IP and the server ports on the mini are clearly visible and connectable. The mini has the following ports open: ssh/22, ARD/5900 and 8080+9090 for the XBMC iOS client Constellation. I also have Synology NAS which apart from LAN file serving over AFP and WebDAV only serves up an OpenVPN/1194 and a PPTP/1732 server. When outside of the LAN I connect to this from my laptop over OpenVPN and over PPTP from my iPhone. I only want to connect through AFP/548 from the mini to the NAS. The border firewall (SRX5308) just works excellently, stable and with a very high throughput when streaming from various VOD services. My connection is a 100/10 with a close to theoretical max throughput. The ruleset is as follows Inbound: PPTP/1723 Allow always to 10.0.0.40 (NAS/VPN server) from a restricted IP range >corresponding to possible cell provider range OpenVPN/1194 Allow always to 10.0.0.40 (NAS/VPN server) from any Outbound: Default outbound policy: Allow Always OpenVPN/1194 TCP Allow always from 10.0.0.40 (NAS) to a.b.8.1-a.b.8.254 (VPN provider) OpenVPN/1194 UDP Allow always to 10.0.0.40 (NAS) to a.b.8.1-a.b.8.254 (VPN provider) Block always from NAS to any On the Mini I have disabled the OSX Application Level Firewall because it throws popups which don't remember my choices from one time to another and that's annoying on a media server. Instead I run Little Snitch which controls outgoing connections nicely on an application level. I have configured the excellent OSX builtin firewall pf (from BSD) as follows pf.conf (Apple App firewall tie-ins removed) (# replaced with % to avoid formatting errors) ### macro name for external interface. eth_if = "en0" vpn_if = "tap0" ### wifi_if = "en1" ### %usb_if = "en3" ext_if = $eth_if LAN="{10.0.0.0/24}" ### General housekeeping rules ### ### Drop all blocked packets silently set block-policy drop ### all incoming traffic on external interface is normalized and fragmented ### packets are reassembled. scrub in on $ext_if all fragment reassemble scrub in on $vpn_if all fragment reassemble scrub out all ### exercise antispoofing on the external interface, but add the local ### loopback interface as an exception, to prevent services utilizing the ### local loop from being blocked accidentally. ### set skip on lo0 antispoof for $ext_if inet antispoof for $vpn_if inet ### spoofing protection for all interfaces block in quick from urpf-failed ############################# block all ### Access to the mini server over ssh/22 and remote desktop/5900 from LAN/en0 only pass in on $eth_if proto tcp from $LAN to any port {22, 5900, 8080, 9090} ### Allow all udp and icmp also, necessary for Constellation. Could be tightened. pass on $eth_if proto {udp, icmp} from $LAN to any ### Allow AFP to 10.0.0.40 (NAS) pass out on $eth_if proto tcp from any to 10.0.0.40 port 548 ### Allow OpenVPN tunnel setup over unprotected link (en0) only to VPN provider IPs ### and port ranges pass on $eth_if proto tcp from any to a.b.8.0/24 port 1194:1201 ### OpenVPN Tunnel rules. All traffic allowed out, only in to ports 4100-4110 ### Outgoing pings ok pass in on $vpn_if proto {tcp, udp} from any to any port 4100:4110 pass out on $vpn_if proto {tcp, udp, icmp} from any to any So what are my goals and what does the above setup achieve? (until you tell me otherwise :) 1) Full LAN access to the above ports on the mini/media server (including through my own VPN server) 2) All internet traffic from the mini/media server is anonymized and tunneled over VPN 3) If OpenVPN/Tunnelblick on the mini drops the connection, nothing is leaked both because of pf and the router outgoing ruleset. It can't even do a DNS lookup through the router. So what do I have to hide with all this? Nothing much really, I just got carried away trying to stop port scans through the VPN tunnel :) In any case this setup works perfectly and it is very stable. The Problem at last! I want to run a minecraft server and I installed that on a separate user account on the mini server (user=mc) to keep things partitioned. I don't want this server accessible through the anonymized VPN tunnel because there are lots more port scans and hacking attempts through that than over my regular IP and I don't trust java in general. So I added the following pf rule on the mini: ### Allow Minecraft public through user mc pass in on $eth_if proto {tcp,udp} from any to any port 24983 user mc pass out on $eth_if proto {tcp, udp} from any to any user mc And these additions on the border firewall: Inbound: Allow always TCP/UDP from any to 10.0.0.40 (NAS) Outbound: Allow always TCP port 80 from 10.0.0.40 to any (needed for online account checkups) This works fine but only when the OpenVPN/Tunnelblick tunnel is down. When up no connection is possbile to the minecraft server from outside of LAN. inside LAN is always OK. Everything else functions as intended. I believe the redirect_gateway push is close to the root of the problem, but I want to keep that specific VPN provider because of the fantastic throughput, price and service. The Solution? How can I open up the minecraft server port outside of the tunnel so it's only available over en0 not the VPN tunnel? Should I a static route? But I don't know which IPs will be connecting...stumbles How secure would to estimate this setup to be and do you have other improvements to share? I've searched extensively in the last few days to no avail...If you've read this far I bet you know the answer :)

  Read the article

• Setting Default Ubuntu eth port

  - by No1_Melman

  Background: I have a desktop computer running Ubuntu 12.04. I have installed DRBL to handle DHCP server and Clonezilla Server. I have a network card in my desktop with 2 ports in it. These 2 ports are bonded together and are used by DRBL. There is a 3rd port integrated in the motherboard. I want to use this 3rd port for internet. DRBL knows that this is set for internet. Ubuntu Network-Manager has stopped recognising the connections (device not managed). It use to say that eth1 was default (first port in the network card) I want eth0 to be default as that is the Internet port. Question: How do I make network-manager see eth0 as the defualt port?

  Read the article

• BizTalk Orchestration & Port Tutorial Part 2

  - by bosuch

  In Part 1 I showed how to create and publish a simple Orchestration demo. Now we’ll finish configuring it in the admin console and test it. Open the BizTalk Server 2009 Administration Console, and expand BizTalk Server 2009 Administration, then Applications. You should have an entry for OrchestrationPortDemo – expand it as well. First, we’ll add the Receive Port – the place that we’ll drop the test file. Right-click on Receive Ports and select New One-way Receive Port. On the General tab, name it InputPort, then click over to Receive Locations.   Click New to add a new location. Your receive location can be FTP, SQL, WCF, SharePoint, or many other choices, but for this demo we’ll add a File location. Click the Configure button and set a receive folder (something like “C:\PortDemo\”) and a file mask (stick with “*.xml” for now) and click OK three times to create your Receive Port.   Next we’ll create the Send port – the location where BizTalk will drop the file. Right-click on Send Ports and choose New Static One-way Send Port. Give it an appropriate name, and configure the FILE Transport Properties as shown:   Click OK twice and your Send Port will be created. Now we’ll configure the Orchestration Bindings. Click on Orchestrations, then right-click the orchestration itself and select Properties. Select the Bindings tab. Choose BizTalkServerApplication as the host, and select the Send and Receive ports you previously created, as shown:   Now it’s time to fire everything up. Right-click on the send port you created and click Start. Once the Status column displays “Started”, click on Receive Locations and Enable the Receive Location previously created. Finally, start the Orchestration. Now, time to test! Create a simple xml file like: <root>    <Node1>Test</Node1>    <Node2>Test</Node2> </root> And drop it into the C:\PortDemo folder. After a couple of seconds the file should disappear – this indicates BizTalk has picked it up for processing. Look in the C:\PortDemo\Output folder and you should see an xml file with a GUID for a name, like {7C50104F-FC3E-4A49-B2FA-4F560A37636D}.xml. Open it to verify that it matches your input file. Practically, this demo doesn’t do a whole heck of a lot, but it shows you the basics for building, publishing and running an orchestration.

  Read the article

• Ubuntu Server - Virtual Box?

  - by user186144

  So I got VirtualBox just for Ubuntu Server, I'm currently Running Ubuntu 12.04 as my main OS. But when I got everything set up in Ubuntu Server 12.04, including my ports forwarded and a test Minecraft server up... I realized that nobody could join my public IP I sent out, not even me! I can connect to the ipv4 address. It acts like I didn't forward my ports. But I forwarded 25565 to Input and Output and they're both TCP and UDP. Is this just a virtual box issue or am I doing something wrong? * Using Eth0 wired connection

  Read the article

• Basic serial port listening application

  Scans for installed serial ports, queries the supported baud rates and start listening to the port in a separate thread.

  Read the article

• Qt 5.2 Beta propose un support complet d'Android et iOS, ainsi que des modules pour l'accès à des fonctionnalités natives

  La version beta de Qt 5.2 est désormais disponible. Beaucoup de choses se sont passées depuis Qt 5.1. En plus des nouvelles plates-formes supportées, beaucoup de nouvelles fonctionnalités ont été ajoutées et de gros changements ont été réalisés sur les rouages internes. Qt partoutQt 5.2 introduit deux ports, prêts pour un usage industriel, pour Android et iOS. Ces deux nouvelles plates-formes ont été au coeur des efforts récents ; ces deux nouveaux ports étendent la promesse de Qt, à savoir viser...

  Read the article

• DrayTek 2820 configuration using public IP addresses

  - by Kev

  I have a /29 range of public IP addresses assigned to me by my ISP. I'm trying to configure a SIP VOIP handset to register with my VOIP provider who recommend using public IP addresses rather than NAT. I have a DrayTek 2820 router flashed with the latest firmware and have configured my router as per DrayTek's FAQ at: How do I use a public subnet on the LAN (non-NAT operation ) ? My IP range is: xx.xx.94.16 -> xx.xx.94.23 This gives a usable range of: xx.xx.94.17 -> xx.xx.94.22 My router's public IP address is: xx.xx.94.17, the SIP VOIP handset is allocated xx.xx.94.18. I have a second internet connection and via that I can ping the handset. However for some reason I can't seem to get it to register with the provider. I tried adding a new Firewall filter to pass through from WAN to LAN: Source: ANY, Destination: xx.xx.94.18, UDP - Ports 1024 -> 65535 Out of interest I also tried opening port 80 to see if I could browse to the phone's admin web interface but no joy. I know that my ISP aren't blocking inbound service ports because I NAT Port Forwarded port 80 to one of my internal web servers and it rendered a test page I had set up. All the NAT settings are reset to factory defaults, i.e. there are no Port Redirection, DMZ Host, Open Ports or Address Mappings configured. The handset I'm using is a GrandStream GXP-2000. Is there anything else I should be doing?

  Read the article

• Why does my Belkin wireless router has eMule port open?

  - by Jeremy Powell

  I have a Belkin F6D4230-4 v1 router. When I port scan it with nmap I get the following: $ sudo nmap -sS -A -T5 192.168.2.1 -p- Starting Nmap 5.00 ( http://nmap.org ) at 2010-04-17 11:40 CDT Interesting ports on 192.168.2.1: Not shown: 65532 closed ports PORT STATE SERVICE VERSION 80/tcp open http Belkin 2307 wifi router http config (IP_SHARER httpd 1.0) |_ html-title: '+i1+' 4661/tcp filtered unknown 4662/tcp filtered edonkey MAC Address: 00:22:75:5D:52:D8 (Belkin International) Device type: WAP|broadband router|firewall|printer|specialized|webcam Running (JUST GUESSING) : Linksys embedded (95%), TRENDnet embedded (95%), Netgear embedded (92%), Canon embedded (89%), On Time RTOS (89%), Symantec embedded (89%), D-Link embedded (86%), Polycom embedded (85%) Aggressive OS guesses: Linksys WRT54GC or TRENDnet TEW-431BRP wireless broadband router (95%), TRENDnet TW100-BRF114 broadband router (95%), Netgear FR114P ProSafe VPN firewall (92%), Canon PIXMA MX850 printer (89%), On Time RTOS (89%), Symantec Firewall/VPN 100 (89%), D-Link DI-714P+ wireless broadband router (86%), Polycom ViewStation video conferencing system (85%) No exact OS matches for host (test conditions non-ideal). Network Distance: 1 hop Service Info: Device: WAP OS and Service detection performed. Please report any incorrect results at http://nmap.org/submit/ . Nmap done: 1 IP address (1 host up) scanned in 21.57 seconds Why are the 4461 and 4462 ports open? This is a basic, out-of-the-box installation.

  Read the article

• Cassandra Remote Connection

  - by Lyuben Todorov

  I'm not managing to connect to cassandra from outside machines. The database is hosted on a windows machine and im trying to connect through a mac (but this shouldn't cause problems) Local connection works: C:\cassandra\bin>cassandra-cli Starting Cassandra Client Connected to: "Test Cluster" on 127.0.0.1/9160 Welcome to Cassandra CLI version 1.1.6 But fails from other machines on the same network bin/cassandra-cli --host 192.168.0.10 --port 9160 org.apache.thrift.transport.TTransportException: java.net.ConnectException: Operation timed out at org.apache.thrift.transport.TSocket.open(TSocket.java:183) at org.apache.thrift.transport.TFramedTransport.open(TFramedTransport.java:81) at org.apache.cassandra.cli.CliMain.connect(CliMain.java:70) at org.apache.cassandra.cli.CliMain.main(CliMain.java:246) Exception connecting to 192.168.0.10/9160. Reason: Operation timed out. Welcome to Cassandra CLI version 1.2.0-beta3 Type 'help;' or '?' for help. Type 'quit;' or 'exit;' to quit. There is a router on the network but these ports have been triggred Ports: 1024, 7000, 7001, 7199, 9160 And the same ports were forwarded to 192.168.0.10 (where Cassandra is hosted) Cassandra version is 1.0.7 And the settings I think i need to change in cassandra.yaml listen_address: 192.168.0.10 rpc_address: I'm not really sure if I've missed any steps. Any help would be appreciated.

  Read the article

• Cisco SG 300-28P PoE switch appears to have damaged my domain server's network IF

  - by cdonner

  I just replaced the old HP ProCurve switch with a new Cisco SG 300-28P managed switch. It has PoE on all ports. Everything works, except for my domain server that went offline and the network interface appears to be dead. Windows says the network cable is disconnected, and no lights blink on the switch. Tried different cables and different ports on the switch. The Cisco PoE ports are supposed to be auto-sensing, i.e. not to send power to a device that cannot handle it. Is this technique not 100% reliable? The server is a SHUTTLE XS35V2 with an onboard network chip, so it is probably fried. My questions: is this plausible? who's fault is it - Shuttle or Cisco (i.e. which support line should I try first)? UPDATE: I did go back and tried another switch between the server and the Cisco switch, and indeed, the connection came back to live. When everything is powered down and I start fresh, with the server connected to the Cisco switch, the port light will blink for a while and the connection status is "No Internet connection" at first until it goes off after about 20 seconds and the connection status changes to "Network cable disconnected". On the other switch it works. Clearly not a PoE issue now. I will start looking into the Cisco's onboard diagnostic functions, but so far I have not noticed anything unusual in the log.

  Read the article

• Ubuntu 12.04 cloud edition on Amazon - Apache2 - /etc

  - by jdog

  I have setup a web server on Amazon with 3 Virtual hosts. For some reason I can't get any of the sites going on it, they all show a 404 error. /var/log/apache2/error.log shows "File does not exist: /etc/apache2/htdocs" I have checked: a2ensite all my virtual hosts actually checked softlinks in sites-enabled access rights in /var/www to 777, in case user is not www-data grep -r htdocs /etc/apache2 (returns nothing) ports.conf has NameVirtualHost directive exactly matching Virtual Hosts What else could this be? ports.conf # If you just change the port or add more ports here, you will likely also # have to change the VirtualHost statement in # /etc/apache2/sites-enabled/000-default # This is also true if you have upgraded from before 2.2.9-3 (i.e. from # Debian etch). See /usr/share/doc/apache2.2-common/NEWS.Debian.gz and # README.Debian.gz NameVirtualHost 107.20.169.163:80 Listen 80 <IfModule mod_ssl.c> # If you add NameVirtualHost *:443 here, you will also have to change # the VirtualHost statement in /etc/apache2/sites-available/default-ssl # to <VirtualHost *:443> # Server Name Indication for SSL named virtual hosts is currently not # supported by MSIE on Windows XP. Listen 443 </IfModule> <IfModule mod_gnutls.c> Listen 443 </IfModule> sites-available/www.seleconlight.com <VirtualHost 107.20.169.163:80> ServerName www.seleconlight.com DocumentRoot /var/www/www.seleconlight.com CustomLog /var/log/apache2/www.seleconlight.com-access.log combined ErrorLog /var/log/apache2/www.seleconlight.com-error.log </VirtualHost>

  Read the article

• Port forwarding for samba

  - by EternallyGreen

  Alright, here's the setup: Internet - Modem - WRT54G - hubs - winxp workstations & linux smb server. Its basically a home-style distributed internet connection setup, except its at a school. What I want is remote, offsite smb access. I figured I'd need to find out which ports need forwarding and then forward them to the server on the router. I'm told in another question on SF that multiple ports will need forwarding, and it gets somewhat complicated. One of the things I need to know is which ports require forwarding for this, and what complications or vulnerabilities could arise from this. Any additional information you think I should have before doing this would be great. I'm told SMB doesn't support encryption, which is fine. Given I set up authentication/access control, all this means is that once one of my users authenticates and starts downloading data, the unencrypted traffic could be intercepted and read by a MITM, correct? Given that that's the only problem arising from lack of encryption, this is of no concern to me. I suppose that it could also mean a MITM injecting false data into the data stream, eg: user requests file A, MITM intercepts and replaces the contents of file A with some false data. This isn't really an issue either, because my users would know that something was wrong, and its not likely anyone would have incentive to do this anyway. Another thing I've been informed of is Microsoft's poor implementation of SMB, and its crap track record for security. Does this apply if only the client-end is MS? My server is linux.

  Read the article

• iptables port forwarding works only for localhost

  - by Venki

  Below is my iptables config. I used this for my accessing a node js website running in port 9000 through port 80. This works fine only if access the website through local host / loop back. When I try to use the ip of eth0, which is assigned by my router through dcp. this does not work, when I use ip like 192.168.0.103 to access the website. I am not able to figure what is wrong here, Already burnt a day in this, still not able to figure out :( Edit: ( more information) Earlier, I was using this configuration to develop the website, i had configured the domain name to point to 127.0.0.1 in the /etc/hosts file. It was working fine, but now I am trying to deploy the website in a vps with static ip, This configuration does not work with both static IP. # redirect port 80 to port 9000 *nat :PREROUTING ACCEPT [57:3896] :INPUT ACCEPT [0:0] :OUTPUT ACCEPT [4229:289686] :POSTROUTING ACCEPT [4239:290286] -A PREROUTING -p tcp -m tcp --dport 80 -j REDIRECT --to-ports 9000 -A OUTPUT -d 127.0.0.1/32 -p tcp -m tcp --dport 80 -j REDIRECT --to-ports 9000 COMMIT # Allow HTTP and HTTPS connections from anywhere (the normal ports for websites and SSL). -A INPUT -p tcp --dport 80 -j ACCEPT -A INPUT -p tcp --dport 443 -j ACCEPT -A INPUT -p tcp --dport 9000 -j ACCEPT -A INPUT -j REJECT

  Read the article

• Converting DisplayPort and/or HDMI to DVI-D?

  - by Jeff Atwood

  Newer Radeon video cards come with four ports standard: DVI (x2) HDMI DisplayPort If I want to run three 24" monitors, all of which are DVI only, from this video card -- is it possible to convert either the HDMI or DisplayPort to DVI? If so, how? And which one is easier/cheaper to convert? I did a little research and it looks like there isn't a simple "dongle" method. I found this DisplayPort to DVI-D Dual Link Adapter but it's $120; almost cheaper to buy a new monitor that supports HDMI or DisplayPort inputs at that point! There's also a HDMI to DVI-D adapter at Monoprice but I'm not sure it will work, either. AnandTech seems to imply that you do need the DisplayPort-to-DVI: The only catch to this specific port layout is that the card still only has enough TMDS transmitters for two ports. So you can use 2x DVI or 1x DVI + HDMI, but not 2x DVI + HDMI. For 3 DVI-derived ports, you will need an active DisplayPort-to-DVI adapter.

  Read the article

• tcp msl timeout

  - by iamrohitbanga

  The following is given in the book TCP IP Illustrated by Stevens Quiet Time Concept The 2MSL wait provides protection against delayed segments from an earlier incarnation of a connection from being interpreted as part of a new connection that uses the same local and foreign IP addresses and port numbers. But this works only if a host with connections in the 2MSL wait does not crash. What if a host with ports in the 2MSL wait crashes, reboots within MSL seconds, and immediately establishes new connections using the same local and foreign IP addresses and port numbers corresponding to the local ports that were in the 2MSL wait before the crash? In this scenario, delayed segments from the connections that existed before the crash can be misinterpreted as belonging to the new connections created after the reboot. This can happen regardless of how the initial sequence number is chosen after the reboot. To protect against this scenario, RFC 793 states that TCP should not create any connections for MSL seconds after rebooting. This is called the quiet time Few implementations abide by this since most hosts take longer than MSL seconds to reboot after a crash. Do operating systems wait for 2MSL seconds now after a reboot before initiating a TCP connection. The boot times are also less these days. Although the ports and sequence numbers are random but is this wait implemented in Linux?

  Read the article

< Previous Page | 19 20 21 22 23 24 25 26 27 28 29 30  | Next Page >