Search Results

Search found 9235 results on 370 pages for 'social networking'.

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

Page 23/370 | < Previous Page | 19 20 21 22 23 24 25 26 27 28 29 30  | Next Page >

  • Audio and video streaming using Network Simulator in Linux

    - by Parth_90
    I am working on a project which is to show the simulation of streaming of audio and video data in wireless networks. I want to show the simulation that involves a base station, with few wireless stations. The base station should start sending data once it computes a certain value . On receiving the data, each wireless must begin communicating with the base station. I have gone through basic NS-2 tutorials from over here but I am not getting how to go about integrating it with my project. Can anyone tell me how to do it using NS2 or any other network simulator?

    Read the article

  • Linux wireless disconnect every 20 minutes

    - by james
    My laptop uses CentOS 6.3 with kernel 2.6.32-279.el6.x86_64. My wireless adaptor is Intel Corporation Centrino Wireless-N 1000. My wireless connection always get off after about 20 minutes. The network applet shows the connection is still on with good signal strength, but I just cannot load any web pages even the configuration page of the wireless router. The problem will continue until I disable and reconnect the wireless. Other devices like my cell phone uses the same wireless network without the problem. Even yesterday I'm using the same laptop with Fedora 17 without this problem. I also searched the internet and someone said running services NetworkManager and network simultaneously may be a problem. But I cannot stop any one of them because: if I stop network and start NetworkManager, the network service will start automatically; if I stop NetworkManager and run network, it says "Device does not seem to be present, delaying initialization." when trying to bringing on the wireless. What shall I do to get rid of the problem? Thank you very much!

    Read the article

  • Setting up dual wireless routers

    - by JasCav
    I have two wireless routers (one is the router supplied by Verizon - MI424-WR ActionTek and the other is DD-WRT Buffalo router). I want to set them up so that I have the second router (Buffalo) on its own subnet and two SSIDs so I can put different devices on different routers and so I can put my web server on the first router and put most of my other computers behind the second router for a little extra protection in case of a compromise. From my understanding, I have to hook the two routers together so that the LAN from the Verizon router plugs into the WAN port of the Buffalo router. This is where I get stuck. What settings do I need to look for to setup the Buffalo on its own subnet? Do I need to do anything with the Verizon router, or are the configuration changes done to the Buffalo?

    Read the article

  • Wifi Snooping over phone

    - by pulsarjune
    I connect to the wifi acccess-point at work, but recently I suspect that data on my phone is being snooped-out from my phone connected to my office's Wifi network. [Phone Model: Sony Ericsson Xperia Neo V, Android v2.3; Wifi accespoint: Belkin G] How can i check my suspicion? Or What are the ways i could get over them? (obviously i want to stay connected to the wifi n/w) Any thoughts on these points?

    Read the article

  • What's the fastest way to store/access large files?

    - by philfreo
    I do a lot of video editing on my Mac and need a way to store very large (30 GB) files, and don't have room on my HD. A USB/Firewire external hard drive would work, but it seems way too slow for consistently working with such large files. I've also considered buying another computer, with a large hard drive, and putting it on the same network with a shared folder. What's the fastest / most efficient way to do this? Please consider USB 2.0 speeds, hard drive read times, ethernet speeds, etc. Are there other options I should consider?

    Read the article

  • pull bandwidth from wireless WAN into local LAN

    - by cortical
    We have a local network (A) of about 50 computers connected via gigabit ethernet. We get a connection to the internet using two broadband connections to a backbone and distribute the bandwidth across the 50 computers using a CISCO 1811 router, but the bandwidth is not enough for everybody. There is a campus wide wireless network(B) that has very high bandwidth, is there a device or way to setup multiple individual connections to network B and supply the bandwidth to our network A?

    Read the article

  • After connecting wlan0 to bridge interface (and then removing it), can't connect to AP

    - by gmonk
    I'm on a laptop running Debian Jessie with kernel 3.13-1-amd64; lspci shows that my wireless NIC + driver is 04:00.0 Network controller: Intel Corporation Wireless 3160 (rev 83) Subsystem: Intel Corporation Dual Band Wireless-AC 3160 Kernel driver in use: iwlwifi This has been working without any problems, until I tried creating a bridge for lxc containers to use. I did the same thing as this person here: How-to set up a network bridge on a laptop for LXC use? -- and ended up having the same problem as this poster did, so I decided to "undo" my actions. This hasn't been successful. Actions taken so far: To configure the bridge: #> ip link add type veth #> iw dev wlan0 set 4addr on #> ifconfig veth0 up #> brctl addbr br0 #> brctl addif br0 wlan0 #> brctl addif br0 veth0 #> ifconfig br0 192.168.0.4/24 #> ifconfig wlan0 0.0.0.0 To "deconfigure": #> brctl delif br0 wlan0 #> brctl delif br0 veth0 #> iw dev wlan0 set 4addr off #> ifconfig veth0 down #> ifconfig wlan0 down #> ifconfig br0 down #> brctl delbr br0 Now, dmesg and /var/log/syslog show repeated attempts at connecting to the AP that was working before, which fail after authentication: May 27 09:16:01 myhostname kernel: [11350.757172] wlan0: authenticate with 00:18:f8:54:a3:d6 May 27 09:16:01 myhostname kernel: [11350.759036] wlan0: send auth to 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:01 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: scanning -> authenticating May 27 09:16:01 myhostname wpa_supplicant[8946]: wlan0: Trying to associate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:01 myhostname kernel: [11350.762615] wlan0: authenticated May 27 09:16:01 myhostname kernel: [11350.762753] iwlwifi 0000:04:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP May 27 09:16:01 myhostname kernel: [11350.762755] iwlwifi 0000:04:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP May 27 09:16:01 myhostname kernel: [11350.765080] wlan0: associate with 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:01 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: authenticating -> associating May 27 09:16:01 myhostname kernel: [11350.767474] wlan0: RX AssocResp from 00:18:f8:54:a3:d6 (capab=0x411 status=12 aid=0) May 27 09:16:01 myhostname kernel: [11350.767476] wlan0: 00:18:f8:54:a3:d6 denied association (code=12) May 27 09:16:01 myhostname wpa_supplicant[8946]: wlan0: CTRL-EVENT-ASSOC-REJECT bssid=00:18:f8:54:a3:d6 status_code=12 May 27 09:16:01 myhostname kernel: [11350.788475] wlan0: deauthenticating from 00:18:f8:54:a3:d6 by local choice (reason=3) May 27 09:16:01 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associating -> disconnected May 27 09:16:01 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: disconnected -> scanning May 27 09:16:02 myhostname dhclient: DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 14 May 27 09:16:04 myhostname wpa_supplicant[8946]: wlan0: SME: Trying to authenticate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:04 myhostname kernel: [11354.559579] wlan0: authenticate with 00:18:f8:54:a3:d6 May 27 09:16:04 myhostname kernel: [11354.561458] wlan0: send auth to 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:04 myhostname wpa_supplicant[8946]: wlan0: Trying to associate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:04 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: scanning -> associating May 27 09:16:04 myhostname kernel: [11354.563445] wlan0: authenticated May 27 09:16:04 myhostname kernel: [11354.563631] iwlwifi 0000:04:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP May 27 09:16:04 myhostname kernel: [11354.563633] iwlwifi 0000:04:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP May 27 09:16:04 myhostname kernel: [11354.565727] wlan0: associate with 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:04 myhostname wpa_supplicant[8946]: wlan0: Associated with 00:18:f8:54:a3:d6 May 27 09:16:04 myhostname kernel: [11354.568091] wlan0: RX AssocResp from 00:18:f8:54:a3:d6 (capab=0x411 status=0 aid=9) May 27 09:16:04 myhostname kernel: [11354.569030] wlan0: associated May 27 09:16:04 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associating -> associated May 27 09:16:05 myhostname kernel: [11354.978204] wlan0: deauthenticated from 00:18:f8:54:a3:d6 (Reason: 15) May 27 09:16:05 myhostname wpa_supplicant[8946]: wlan0: CTRL-EVENT-DISCONNECTED bssid=00:18:f8:54:a3:d6 reason=15 May 27 09:16:05 myhostname kernel: [11354.992729] cfg80211: Calling CRDA to update world regulatory domain May 27 09:16:05 myhostname kernel: [11354.995004] cfg80211: World regulatory domain updated: May 27 09:16:05 myhostname kernel: [11354.995005] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) May 27 09:16:05 myhostname kernel: [11354.995006] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm) May 27 09:16:05 myhostname kernel: [11354.995007] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm) May 27 09:16:05 myhostname kernel: [11354.995007] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm) May 27 09:16:05 myhostname kernel: [11354.995008] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm) May 27 09:16:05 myhostname kernel: [11354.995009] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm) May 27 09:16:05 myhostname kernel: [11354.995010] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm) May 27 09:16:05 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associated -> disconnected May 27 09:16:05 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: disconnected -> scanning May 27 09:16:09 myhostname wpa_supplicant[8946]: wlan0: SME: Trying to authenticate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:09 myhostname kernel: [11358.763968] wlan0: authenticate with 00:18:f8:54:a3:d6 May 27 09:16:09 myhostname kernel: [11358.765796] wlan0: send auth to 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:09 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: scanning -> authenticating May 27 09:16:09 myhostname wpa_supplicant[8946]: wlan0: Trying to associate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:09 myhostname kernel: [11358.769957] wlan0: authenticated May 27 09:16:09 myhostname kernel: [11358.770102] iwlwifi 0000:04:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP May 27 09:16:09 myhostname kernel: [11358.770104] iwlwifi 0000:04:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP May 27 09:16:09 myhostname kernel: [11358.770846] wlan0: associate with 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:09 myhostname kernel: [11358.773358] wlan0: RX AssocResp from 00:18:f8:54:a3:d6 (capab=0x411 status=12 aid=0) May 27 09:16:09 myhostname kernel: [11358.773361] wlan0: 00:18:f8:54:a3:d6 denied association (code=12) May 27 09:16:09 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: authenticating -> associating May 27 09:16:09 myhostname wpa_supplicant[8946]: wlan0: CTRL-EVENT-ASSOC-REJECT bssid=00:18:f8:54:a3:d6 status_code=12 May 27 09:16:09 myhostname kernel: [11358.802187] wlan0: deauthenticating from 00:18:f8:54:a3:d6 by local choice (reason=3) May 27 09:16:09 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associating -> disconnected May 27 09:16:09 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: disconnected -> scanning May 27 09:16:12 myhostname wpa_supplicant[8946]: wlan0: SME: Trying to authenticate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:12 myhostname kernel: [11362.573442] wlan0: authenticate with 00:18:f8:54:a3:d6 May 27 09:16:12 myhostname kernel: [11362.575270] wlan0: send auth to 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:12 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: scanning -> authenticating May 27 09:16:12 myhostname wpa_supplicant[8946]: wlan0: Trying to associate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:12 myhostname kernel: [11362.580334] wlan0: authenticated May 27 09:16:12 myhostname kernel: [11362.580503] iwlwifi 0000:04:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP May 27 09:16:12 myhostname kernel: [11362.580516] iwlwifi 0000:04:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP May 27 09:16:12 myhostname kernel: [11362.583508] wlan0: associate with 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:12 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: authenticating -> associating May 27 09:16:12 myhostname wpa_supplicant[8946]: wlan0: Associated with 00:18:f8:54:a3:d6 May 27 09:16:12 myhostname kernel: [11362.585908] wlan0: RX AssocResp from 00:18:f8:54:a3:d6 (capab=0x411 status=0 aid=9) May 27 09:16:12 myhostname kernel: [11362.586781] wlan0: associated May 27 09:16:12 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associating -> associated May 27 09:16:13 myhostname kernel: [11362.947693] wlan0: deauthenticated from 00:18:f8:54:a3:d6 (Reason: 15) May 27 09:16:13 myhostname wpa_supplicant[8946]: wlan0: CTRL-EVENT-DISCONNECTED bssid=00:18:f8:54:a3:d6 reason=15 May 27 09:16:13 myhostname kernel: [11362.973461] cfg80211: Calling CRDA to update world regulatory domain May 27 09:16:13 myhostname kernel: [11362.975673] cfg80211: World regulatory domain updated: May 27 09:16:13 myhostname kernel: [11362.975675] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) May 27 09:16:13 myhostname kernel: [11362.975676] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm) May 27 09:16:13 myhostname kernel: [11362.975677] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm) May 27 09:16:13 myhostname kernel: [11362.975678] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm) May 27 09:16:13 myhostname kernel: [11362.975678] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm) May 27 09:16:13 myhostname kernel: [11362.975679] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm) May 27 09:16:13 myhostname kernel: [11362.975679] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm) May 27 09:16:13 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associated -> disconnected May 27 09:16:13 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: disconnected -> scanning May 27 09:16:14 myhostname NetworkManager[13992]: <warn> Activation (wlan0/wireless): association took too long. May 27 09:16:14 myhostname NetworkManager[13992]: <info> (wlan0): device state change: config -> failed (reason 'no-secrets') [50 120 7] May 27 09:16:14 myhostname NetworkManager[13992]: <info> Marking connection 'Auto myaccesspoint' invalid. May 27 09:16:14 myhostname NetworkManager[13992]: <warn> Activation (wlan0) failed for connection 'Auto myaccesspoint' May 27 09:16:14 myhostname NetworkManager[13992]: <info> (wlan0): device state change: failed -> disconnected (reason 'none') [120 30 0] May 27 09:16:14 myhostname NetworkManager[13992]: <info> (wlan0): deactivating device (reason 'none') [0] May 27 09:16:14 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: scanning -> disconnected The things that jump out at me are "deauthenticating ... by local choice( reason=3)" and the lines that contain "(reason=15)". I've tried various fixes: iwconfig wlan0 power off killing wpa_supplicant connecting with iwconfig + dhclient instead of gnome's network -manager explicitly configuring wlan0 in /etc/network/interfaces creating a /etc/wpa_supplicant.conf file ...but nothing seems to work. I'm not sure what I did wrong, or what step I've skipped in trying to get wlan0 back as a non-bridged device -- I removed it from the bridge and then deleted the bridge itself. Any ideas?

    Read the article

  • How to use a different Ethernet connection

    - by SteveC
    I'm running a virtual machine at home which has a VPN connection to our main office, but I also want to connect to a share on another machine at home. When I check with IPCONFIG I can see two ethernet connections ... my work VPN ... Ethernet adapter Local Area Connection* 11: Connection-specific DNS Suffix . : Link-local IPv6 Address . . . . . : xxxx::xxxx:xxxx:xxxx:xxxxxxx IPv4 Address. . . . . . . . . . . : XXX.XXX.XXX.XXX Subnet Mask . . . . . . . . . . . : 255.255.254.0 Default Gateway . . . . . . . . . : XXX.XXX.XXX.XXX and home local ... Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : lan Link-local IPv6 Address . . . . . : xxxx::xxxx:xxxx:xxxx:xxxxxxx IPv4 Address. . . . . . . . . . . : 192.168.1.70 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : What's weird is when I've been working before with a plugged-in ethernet cable I've not had any problem getting to the share? I can PING the other machine, but I can't access the share at ... \\othermachine\c$ I tried 'TRACERT` but that disappears off to the work network and eventually gets back to the local other machine after a few time-outs Is there anyway to "force" the connection to stay local ? UPDATE: the VPN is AEP SSL Tunnel

    Read the article

  • How to tell if you are connected to Wireless B, G or N?

    - by Raheel Khan
    I am using Windows 7 on all wired desktops and wireless laptops in my home network. I recently upgraded my Ethernet switch to Gigabit and instantly noticed an increase in throughput in wired devices. I also bought a Wireless-N WAP but with degredation in wireless file transfer speeds. I have been told that a number of reasons could affect wireless speeds including which WAP is used, how many wireless devices are connected, which security mode is used, etc. However, that remains irrelevant to my question. Each of my laptops claim to support Wireless-N but I cannot seem to figure out how to determine if the laptops are truly running Wireless-N or are connected to the WAP through some sort of mixed-mode. I do not have control of the WAP device so cannot tell what mode it is running in. Is there a way to tell which mode is being used and what the throughput is for each connected device without having access to the WAP interface?

    Read the article

  • Machine only responds to network requests from machines it is pinging

    - by ILikeFood
    I have two machines. WOPR: Ubuntu server edition 10.10 LTS 32 bit Adam Selene: Windows 7 home premium 64 bit / Ubuntu Desktop 10.10 LTS 64 bit I want to be able to SSH from Adam Selene to WOPR, so I connect them to the same network. Here's where things get weird. I cannot connect to WOPR in any way under normal circumstances. But, if WOPR is pinging Adam, then it starts responding to ping requests, HTTP gets, and SSH tunnels. I'm an amateur, and brand new to Ubuntu server, so I suspect there's a misconfiguration somewhere, but there's an off chance it's a bug in the OS. Does anyone know what might cause this behavior? Thanks a lot!

    Read the article

  • TCP connection between PCs in home wi-fi network

    - by Nordvind
    I want to establish a connection between 2 PCs. Point is to practice in writing client-server applications and similar stuff. I've heard around, that I can access another PC in network by address like "Router IP:port number". Am I right or i got it wrong? So how do I configure router to let connections to certain ports? And what would address look like, if I'm, say, connecting to 80 port on my home server? P.S. Will be grateful for links to some tutorials on this matter, if any.

    Read the article

  • Windows 8 doesn't automatically join Wi-Fi network if Ethernet connection is active

    - by Herb Caudill
    In Windows 7, my laptop would automatically join both an Ethernet network and the Wi-Fi network in my house (both going through the same router). In Windows 8, if the Ethernet connection is present, it doesn't join the Wi-Fi network at all. The reason I noticed this is that if Wi-Fi isn't active, I don't see my AirPlay speakers. My wireless printer is also unavailable until I manually connect to Wi-Fi. To recap: When I turn on my computer and it's connected to Ethernet, this is what my Network Connections control panel looks like: After I manually join my Wi-Fi network, it looks like this: I would prefer for it to join both networks automatically on startup, the way it did in Windows 7. Is there a way to make this happen?

    Read the article

  • Why can't I connect to my router's config page with Windows 7?

    - by user17940
    I've got a Belkin wireless router, and just bought a new Dell computer with Windows 7 pre-installed. I can connect to the Internet and my home network just fine, but when I try to visit my router's configuration page at http://192.168.2.1, I get a "Connection was reset" error. Nothing I do will make the router's configuration page come up in my web browser. More background information: I could always get to the router's config page from my Windows XP machine. I never had any trouble prior to getting this Windows 7 computer. I can ping 192.168.2.1 successfully from my Windows 7 computer. My PC is connected to the router by a physical CAT5 cable, not via wireless. Every device connected to my router, including the new computer, can get to the Internet with no problem. Here are some things that did not solve the problem: I tried turning off IPV6 in Windows. I tried turning off my firewall and antivirus software I tried using https instead of http I tried disabling and then enabling the network connection in Windows I tried reverting my network card driver back to an older version I have tried both Firefox and Internet Explorer web browsers. Has anyone experienced something like this before, and solved it? Thanks a lot for your help!

    Read the article

  • How can I connect my Xbox to my Mac on my network

    - by codecowboy
    I have a wireless router/modem (Router 1) in my living room. This is connected to the internet (cable). Wireless is disabled as the router has a terrible wireless range. My Xbox is connected via ethernet to Router 1. Another LAN output from Router 1 connects to a powerline adapter. Router 1 acts as a DHCP server on 192.168.0.x and has the IP 192.168.0.1 In a second room I have Router 2. This has the powerline feed from Router 1 going into the WAN socket. This router runs the Tomato Firmware and acts as a wireless router for the rest of the house using the IP range 192.168.1.x. Router 2 IP is 192.168.1.1. My Mac is connected to Router 2 using a LAN cable and has the IP 192.168.0.133. Several mobile devices need wireless access. I want an ethernet connection to my Mac, not wireless. I should be able to use software like Connect360 to share media from my Mac to the XBox but the XBox does not see my Mac. I can ping 192.168.0.1 from the Mac. Is this possible using my current setup? If so, how?

    Read the article

  • Ubuntu Natty 11.04, Turning the wireless switch off; switches it off permanently!

    - by ZiGi
    i'm using an hp pavilion dv2000 i turned the wifi switch off by mistake, the LED turned orange and the wifi got disconnected. and now when i turn the switch on, it remains orange and the wifi still isn't functional. this happened before; i found a fix that worked searching google. it was done via terminal commands and i didn't have to download anything but i can't find the solution anymore! wlan0 shows up when i use: :~$iwconfig #BLA BLA BLA #... wlan0 IEEE 802.11abg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off more results: :~$ sudo ifconfig wlan0 up SIOCSIFFLAGS: Operation not possible due to RF-kill :~$ rfkill list all 1: phy0: WirelessLAN Soft blocked: yes Hard blocked: yes :~$ sudo rfkill unblock all :~$ rfkill list all 1: phy0: WirelessLAN Soft blocked: no Hard blocked: yes :~$ sudo ifconfig wlan0 up SIOCSIFFLAGS: Operation not possible due to RF-kill it's still hard blocked! even though the switch is turned on; gives the same result eitherways a direction to a page with a working solution is a much appreciated answer!

    Read the article

  • 802.11g -> wired ethernet bridging not working

    - by Malachi
    Usually people want to go the other direction, but I want to take our relatively fast and stable house 802.11g signal and bridge it to ethernet. I have tried using an Airport Express (the b/g flavor) and my i7 MacBook pro, both to no avail. Word is that the b/g flavor of This flavor of Airport Express maxes at firmware 6.3 which doesn't support this kind of bridging properly. However, I expected my MacBook pro to do the job with its "Internet Sharing" feature. Alas, although my wired PC does sort of see it, it doesn't work out. Strangely, using DHCP the PC receives the same IP address as my MBP uses on the network. Less strangely, but still surprisingly, the wired ethernet port on my mac registers as the IP address of the gateway when queried with IFCONFIG. It sort of makes sense that the mac would "pretend" to be the gateway, but the whole thing just isn't working and seems configured wrong - but all the docs I see say basically "OS X Internet Sharing: click it and go". What do I do? Do i really have to buy more hardware, even though I have plenty of would-be candidates for bridging? Incidentally, the host router originating the 802.11g signal is a belkin 802.11g router, and is documented to support WDS.

    Read the article

  • Is it possible to combine two internet connections to increase performance?

    - by cornjuliox
    I've got a small home network, 3 PCs plus a laptop or two when the relatives come to visit, connected to a single cable internet connection. Now, as soon as everyone starts using the 'net the performance starts to suffer and if the load is heavy enough nobody can get anything done and everyone complains. At one point it was so bad that only one of us could use it at a time. I was researching possible solutions to this problem and I heard that internet cafes that utilize 2 internet connections, possibly from different providers, and have some sort of router that allows them to split the traffic between the both of them, with online games going through one and web traffic going through another. Is this possible? What is the technical term for it, and can/should it be applied to a home network setup or is there another solution to this problem?

    Read the article

  • Connecting multiple access points

    - by mohsen farahanipoor
    I'm working on a big project. We want to create a wireless network throughout the building with 15 floors. My idea is that we should set up one unified wireless access point at least in each floor...in case of signal attenuate, we use Access point extender/repeater. I selected DWL-6600AP from among D-Link industrial access points. I want to implement a single wireless LAN throughout the building. Is it possible to combines multiple DWL-6600 access points to achieving just a single WLAN? Can a wireless switch controller do this task? Can these Access Points interfere with each other? What is the solution? I read D-Link website's learning materials, but I am still confused. My other question is around the connecting these APs to Wireless Switch Controller - Is it possible to use power line for connecting DWL-6600 to Wireless Switch Controller device? My main goal is that clients with portable devices such as laptops should be easily connected to the network to share & have communication without any more manual configuration as they are already connected to a single network.

    Read the article

  • Laptop's wifi router is not emitting signals therefore my PC and Nokia cell are not connecting to internet

    - by umer sanny
    I have a USB internet connection which I plugged into my laptop. I converted my laptop's Wifi into a Wifi router so that I can attach my PC and cell to this network and enjoy internet, but it doesn't work. I have a Dell Inspiron N5110 i7 Windows 7 64-bit laptop, Dell D865 PC and Nokia C5. My PC and cell are showing that there is a new Wifi connection available, but when I connect to it, it won't load any web page. Reason is my laptop's Wifi is not emitting any internet signals or may be some other issue which i dont know.. laptop's adapter is 802.11b/g/n I don't know why. How can I enjoy Wifi internet on laptop, PC and cell at the same time?

    Read the article

  • IP camera's multicast/RTSP conflicting with 2.4GHz Wi-Fi?

    - by jayson
    Here at our business we have a Netgear R7000 running DD-WRT. I have been slowly adding IP cameras which I run using Blue Iris software. The last camera I bought (which is NOT a wireless camera), when I plug it into the network I start having really bad connection issues on the 2.4GHz Wi-Fi network. The 5GHz works fine, just the 2.4GHz all of the sudden has trouble connecting, as if it's conflicting. I've tried playing with the camera settings, different IP addresses, HTTP ports, etc, and discovered it to be a conflict with multicast. When multicast is checked, the Wi-Fi has issues but my video streams via Blue Iris. When unchecked, Wi-Fi works fine but the video won't stream through Blue Iris. The problem is there are no settings in the camera to change the RTSP port, which is set to 34567. Does anyone know something that could fix this issue? It all seems very strange to me but maybe someone has an idea?

    Read the article

  • Laptop connecting to Wifi but not to internet

    - by eddard stark
    My friends laptop is able to connect to the wifi router . Typing 192.168.1.1 in the browser shows the login page for the router . But he cannot connect to the internet. This is true on both windows and linux (dual booting setup) . There are 3 other laptops connecting to the internet via wifi just fine and his was fine too until this happened all of a sudden . I tried doing a tracert from windows to an external ip . The first hop to the modem is fine but then the packets seem to be getting dropped . If his wifi adapter is damaged how is it connecting to the modem via wifi . I havent asked a question here before but this is really weird . If anyone needs any more information I shall post it here.

    Read the article

  • Can't access LAN computers with SSH

    - by endolith
    I got a new Windows 7 machine, and was using VNC,SSH etc to connect to my Ubuntu machine, and it worked fine previously. Now it doesn't work if I use the machine's hostname or local IP, but if I use the DynDNS name, it works. I can also access it from my Android phone using the local hostname over SSH. If I try to connect with SSH to the hostname, it says "Host does not exist". VNC says "Failed to get server address". NX says "no address associated with name", and I don't see it in Windows' "Network" folder. I've rebooted everything. I've turned off Windows firewall. It was working fine a few days ago, but now it's not. How do I figure out what's blocking it?

    Read the article

  • Decreasing lagging on router, while gaming

    - by user2699451
    I had absolutely no idea where to post this question and get a professional answer for it but here goes... Okay, so I guess everyone whos is reading this had played online, and so I was playing LoL again tonight and my brother decided that now was a great time to go on youtube and start watching a movie, so my ping (connecting from South Africa to EU west server) is around 190-220 average, however it started spiking to 2000 and average was 600-800, so it arised the question, how ther hell can I "kick" him off for the time being I tried reasoning it out with him but its like playing chess with a pigeon, he's studying to be an engineer, and I just cant win an argument with him, so i need to step it up a level... I have in the past used the aireplay method by sending deauth packets but it only helped so much, is there another way of either kicking a peer of the local wifi or decreasing the lag spikes while in session or even splitting the bandwidth equally in 2 or 3,etc What do I do p.s. sorry if off topic, if it is not appropriate, just say which website will be able to help or assist me...

    Read the article

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

< Previous Page | 19 20 21 22 23 24 25 26 27 28 29 30  | Next Page >