Search Results

Search found 4878 results on 196 pages for 'sun cluster'.

Page 23/196 | < Previous Page | 19 20 21 22 23 24 25 26 27 28 29 30  | Next Page >

• Virtual machines interconnection inside Proxmox 2.1 Cluster

  - by Anton

  We have 3 physical servers (each with 1 NIC) in different datacentres, all of them are interconnected by openvpn bridged private network (10.x.x.x). Inside this network we have fully functional 3 nodes Proxmox 2.1 cluster. So, actually question is: Is there any "proper" way to make "global" local network (172.16.x.x) for all VMs inside cluster, so even if we move VM from one node to other we could reach it by static IP regardless of it's physical location? BTW, we can't add dedicated NIC to each server. Thanks in advance. EDIT: I have tried to make a separate openvpn bridge for 172.16.x.x, now I have at each server two interfaces: SRV1: openvpnbr1 - 172.16.13.1 vmbr0 - 172.16.1.1 SRV2: openvpnbr1 - 172.16.13.2 vmbr0 - 172.16.2.1 But now there is no connection between those ifaces: SRV1: ping 172.16.13.2 From 172.16.1.1 icmp_seq=2 Destination Host Unreachable SRV2: ping 172.16.13.1 From 172.16.2.1 icmp_seq=2 Destination Host Unreachable If I shut down vmbr0 interfaces, so there is connection between servers over openvpn, but vmbr0 is used by Proxmox... Where I am wrong?

  Read the article

• SBD killing both cluster nodes when there are even small SAN network problems

  - by Wieslaw Herr

  I am having problems with stonith SBD in a openais-based cluster. Some background: The active/passive cluster has two nodes, node1 and node2. They are configured to provide an NFS service to users. To avoid problems with split-brain, they are both configured to use SBD. SBD is using two 1MB disks available to the hosts via an multipath fibre-channel network. The problems start if something happens with the SAN network. For example, today one of the brocade switches got rebooted and both nodes lost 2 out of 4 paths to each disks, which resulted in both nodes committing suicide and rebooting. This, of course, was highly undesirable because a) there were paths left b) even if the switch would be out for 10-20 seconds a reboot cycle of both nodes would take 5-10 minutes and all NFS-locks would be lost. I tried increasing the SBD timeout values (to 10sec+ values, dump attached at the end), however a "WARN: Latency: No liveness for 4 s exceeds threshold of 3 s" hints that something isn't working as I would it expect to. Here is what I would like to know: a) Is SBD working as it should killing nodes when 2 paths are available? b) If not, is the multipath.conf file attached correct? The storage controller we use is an IBM SVC (IBM 2145), should there be any specific configuration for it? (as in multipath.conf.defaults) c) How should I go about increasing the timeouts in SBD attachements: Multipath.conf and sbd dump (http://hpaste.org/69537)

  Read the article

• using i7 "gamer" cpu in a HPC cluster

  - by user1219721

  I'm running WRF weather model. That's a ram intensive, highly parallel application. I need to build a HPC cluster for that. I use 10GB infiniband interconnect. WRF doesn't depends of core count, but on memory bandwidth. That's why a core i7 3820 or 3930K performs better than high-grade xeons E5-2600 or E7 Seems like universities uses xeon E5-2670 for WRF. It costs about $1500. Spec2006 fp_rates WRF bench shows $580 i7 3930K performs the same with 1600MHz RAM. What's interesting is that i7 can handle up to 2400MHz ram, doing a great performance increase for WRF. Then it really outperforms the xeon. Power comsumption is a bit higher, but still less than 20€ a year. Even including additional part I'll need (PSU, infiniband, case), the i7 way is still 700 €/cpu cheaper than Xeon. So, is it ok to use "gamer" hardware in a HPC cluster ? or should I do it pro with xeon ? (This is not a critical application. I can handle downtime. I think I don't need ECC?)

  Read the article

• Setting up a global MySQL Cluster in the cloud

  - by GregB

  I'm giving the question an overhaul to more specifically identify where I need help. I use two tools to manage a bunch of cloud server: Puppet and Rundeck. Both of these can be configured to use a mysql backend. I'd like to setup an instance of each application in both the U.S., and the U.K., treating the U.K. servers as hot stand-bys in case of failure in the U.S. I want to use a MySql cluster so that the data is automatically replicated from the U.S. to the U.K. Because these are hot standbys, high performance is not a goal. Redundancy and data integrity are most important. My question revolves around the setup of the mysql cluster. I want to run three servers, each one running a data node, a sql node, and a management node. Is this a valid configuration for mysql server? If so, could someone point me in the right direction for creating such a setup? I've downloaded the offical tarball, and the official debian, and the documentation for them contradicts many of the online tutorials. I'm installing on Ubuntu 10.04.

  Read the article

• What's In Storage?

  - by [email protected]

  Oracle Flies South for Storage Networking Event Storage Networking World (now simply called SNW) is the place you'll find the most-comprehensive education on storage, infrastructure, and the datacenter in the spring of 2010. It's also the place where you'll see Oracle. During the April 12-15 event in Orlando, Florida, the industry's premiere presentations on storage trends and best practices are combined with hands-on labs covering storage management and IP storage. You'll also have the opportunity to learn about Oracle's Sun storage solutions, from Flash and open storage to enterprise disk and tape. Plus, if you stop by booth 207 in the expo hall, you might walk away with a bookish prize: an Amazon Kindle, courtesy of Oracle. Proving, once again, that education can be quite rewarding.

  Read the article

• Oracle Desktop Virtualization Press Release

  - by [email protected]

  Even though Oracle has introduced new products (HW and SW) and pricing, and part numbers, modified licensing, and an EVP and an SVP have discussed openly where Oracle is going with Virtualization,  you may still have heard from "the other guys' that Oracle isn't going to be keeping the legacy Sun 'Desktop' portfolio.  I think that has soundly been addressed by the press release this morning.  Click here for the release.This is a great way to kick off Oracle's New (fiscal) Year.  As there are more announcements coming - I'll just say "Enjoy!, and "Stay Tuned".

  Read the article

• What's So Smart About Oracle Exadata Smart Flash Cache?

  - by kimberly.billings

  Want to know what's so "smart" about Oracle Exadata Smart Flash Cache? This three minute video explains how Oracle Exadata Smart Flash Cache helps solve the random I/O bottleneck challenge and delivers extreme performance for consolidated database applications. Exadata Smart Flash Cache is a feature of the Sun Oracle Database Machine. With it, you get ten times faster I/O response time and use ten times fewer disks for business applications from Oracle and third-party providers. Read the whitepaper for more information. var gaJsHost = (("https:" == document.location.protocol) ? "https://ssl." : "http://www."); document.write(unescape("%3Cscript src='" + gaJsHost + "google-analytics.com/ga.js' type='text/javascript'%3E%3C/script%3E")); try { var pageTracker = _gat._getTracker("UA-13185312-1"); pageTracker._trackPageview(); } catch(err) {}

  Read the article

• OPN SPECIALIZED Webcasts

  - by Claudia Costa

  OPN Specialized Webcast Series for Partners For the EMEA region the webcasts start at 11:00 CET/10:00GMT. Each training session will run for approximately one hour and include live Q&A. "How to become Specialized in the Applications products portfolio," 25th May 2010,11:00 CET/10:00GMT. Click here for more information& registration. "How to become an OPN Specialized Reseller of Oracle's Sun SPARC Servers, Storage, Software and Services," 1st June 2010,11:00 CET/10:00GMT. Click here for more information& registration.  

  Read the article

• October 2012 Security "Critical Patch Update" (CPU) information and downloads released

  - by user12244672

  The October 2012 security "Critical Patch Update" information and downloads are now available from My Oracle Support (MOS). See http://www.oracle.com/technetwork/topics/security/alerts-086861.html and in particular Document 1475188.1 on My Oracle Support (MOS), http://support.oracle.com, which includes security CVE mappings for Oracle Sun products. For Solaris 11, Doc 1475188.1 points to the relevant SRUs containing the fixes for each issue.  SRU12.4 was released on the CPU date and contains the current cumulative security fixes for the Solaris 11 OS. For Solaris 10, we take a copy of the Recommended Solaris OS patchset containing the relevant security fixes and rename it as the October CPU patchset on MOS.  See link provided from Doc 1475188.1 Doc 1475188.1 also contains references for Firmware, etc., and links to other useful security documentation, including information on Userland/FOSS vulnerabilities and fixes in https://blogs.oracle.com/sunsecurity/

  Read the article

• Using Openfire for distributed XMPP-based video-chat

  - by Yitzhak

  I have been tasked with setting up a distributed video-chat system built on XMPP. Currently my setup looks like this: Openfire (XMPP server) + JingleNodes plugin for video chat OpenLDAP (LDAP server) for storing user information and allowing directory queries Kerberos server for authentication and passwords In testing with one set of machines (i.e. only three), everything works as expected: I can log in to Openfire and it looks up the user information in the OpenLDAP database, which in turn authenticates my user with Kerberos. Now, I want to have several clusters, so that there is a cluster on each continent. A typical cluster will probably contain 2-5 servers. Users logging in will be directed to the closest cluster based on geographical location. Something that concerns me particularly is the dynamic maintenance of contact lists. If a user is using a machine in Asia, for example, how would contact lists be updated around the world to reflect the current server he is using? How would that work with LDAP? Specific questions: How do I direct users based on geographical location? What is the best architecture for a cluster? -- would all traffic need to come into a load-balancer on each one, for example? How do I manage the update of contact lists across all these servers? In general, how do I go about setting this up? What are the pitfalls in doing this? I am inexperienced in this area, so any advice and suggestions would be appreciated.

  Read the article

• What is the optimum way to select the most dissimilar individuals from a population?

  - by Aaron D

  I have tried to use k-means clustering to select the most diverse markers in my population, for example, if we want to select 100 lines I cluster the whole population to 100 clusters then select the closest marker to the centroid from each cluster. The problem with my solution is it takes too much time (probably my function needs optimization), especially when the number of markers exceeds 100000. So, I will appreciate it so much if anyone can show me a new way to select markers that maximize diversity in my population and/or help me optimize my function to make it work faster. Thank you # example: library(BLR) data(wheat) dim(X) mdf<-mostdiff(t(X), 100,1,nstart=1000) Here is the mostdiff function that i used: mostdiff <- function(markers, nClust, nMrkPerClust, nstart=1000) { transposedMarkers <- as.array(markers) mrkClust <- kmeans(transposedMarkers, nClust, nstart=nstart) save(mrkClust, file="markerCluster.Rdata") # within clusters, pick the markers that are closest to the cluster centroid # turn the vector of which markers belong to which clusters into a list nClust long # each element of the list is a vector of the markers in that cluster clustersToList <- function(nClust, clusters) { vecOfCluster <- function(whichClust, clusters) { return(which(whichClust == clusters)) } return(apply(as.array(1:nClust), 1, vecOfCluster, clusters)) } pickCloseToCenter <- function(vecOfCluster, whichClust, transposedMarkers, centers, pickHowMany) { clustSize <- length(vecOfCluster) # if there are fewer than three markers, the center is equally distant from all so don't bother if (clustSize < 3) return(vecOfCluster[1:min(pickHowMany, clustSize)]) # figure out the distance (squared) between each marker in the cluster and the cluster center distToCenter <- function(marker, center){ diff <- center - marker return(sum(diff*diff)) } dists <- apply(transposedMarkers[vecOfCluster,], 1, distToCenter, center=centers[whichClust,]) return(vecOfCluster[order(dists)[1:min(pickHowMany, clustSize)]]) } }

  Read the article

• Hibernate Query Language Problem

  - by Sarang

  Well, I have implemented a distinct query in hibernate. It returns me result. But, while casting the fields are getting interchanged. So, it generates casting error. What should be the solution? As an example, I do have database, "ProjectAssignment" that has three fields, aid, pid & userName. I want all distinct userName data from this table. I have applied query : select distinct userName, aid, pid from ProjectAssignment Whereas the ProjectAssignment.java file has the fields in sequence aid, pid & userName. Now, here the userName is first field in output. So, Casting is not getting possible. Also, query : select aid, pid, distinct userName from ProjectAssignment is not working. What is the proper query for the same ? Or what else the solution ? The code is as below : System Utilization Service Bean Method where I have to retrieve data : public List<ProjectAssignment> getProjectAssignments() { projectAssignments = ProjectAssignmentHelper.getAllResources(); //Here comes the error return projectAssignments; } ProjectAssignmentHelper from where I fetch Data : package com.hibernate; import java.util.List; import org.hibernate.Query; import org.hibernate.Session; public class ProjectAssignmentHelper { public static List<ProjectAssignment> getAllResources() { List<ProjectAssignment> projectMasters; Session session = HibernateUtil.getSessionFactory().openSession(); Query query = session.createQuery("select distinct aid, pid, userName from ProjectAssignment"); projectMasters = (List<ProjectAssignment>) query.list(); session.close(); return projectMasters; } } Hibernate Data Bean : package com.hibernate; public class ProjectAssignment implements java.io.Serializable { private short aid; private String pid; private String userName; public ProjectAssignment() { } public ProjectAssignment(short aid) { this.aid = aid; } public ProjectAssignment(short aid, String pid, String userName) { this.aid = aid; this.pid = pid; this.userName = userName; } public short getAid() { return this.aid; } public void setAid(short aid) { this.aid = aid; } public String getPid() { return this.pid; } public void setPid(String pid) { this.pid = pid; } public String getUserName() { return this.userName; } public void setUserName(String userName) { this.userName = userName; } } Error : For input string: "userName" java.lang.NumberFormatException: For input string: "userName" at java.lang.NumberFormatException.forInputString(NumberFormatException.java:48) at java.lang.Integer.parseInt(Integer.java:447) at java.lang.Integer.parseInt(Integer.java:497) at javax.el.ArrayELResolver.toInteger(ArrayELResolver.java:375) at javax.el.ArrayELResolver.getValue(ArrayELResolver.java:195) at javax.el.CompositeELResolver.getValue(CompositeELResolver.java:175) at com.sun.faces.el.FacesCompositeELResolver.getValue(FacesCompositeELResolver.java:72) at com.sun.el.parser.AstValue.getValue(AstValue.java:116) at com.sun.el.parser.AstValue.getValue(AstValue.java:163) at com.sun.el.ValueExpressionImpl.getValue(ValueExpressionImpl.java:219) at com.sun.faces.facelets.el.TagValueExpression.getValue(TagValueExpression.java:102) at javax.faces.component.ComponentStateHelper.eval(ComponentStateHelper.java:190) at javax.faces.component.ComponentStateHelper.eval(ComponentStateHelper.java:178) at javax.faces.component.UICommand.getValue(UICommand.java:218) at org.primefaces.component.commandlink.CommandLinkRenderer.encodeMarkup(CommandLinkRenderer.java:113) at org.primefaces.component.commandlink.CommandLinkRenderer.encodeEnd(CommandLinkRenderer.java:54) at javax.faces.component.UIComponentBase.encodeEnd(UIComponentBase.java:878) at org.primefaces.renderkit.CoreRenderer.renderChild(CoreRenderer.java:70) at org.primefaces.renderkit.CoreRenderer.renderChildren(CoreRenderer.java:54) at org.primefaces.component.datatable.DataTableRenderer.encodeTable(DataTableRenderer.java:525) at org.primefaces.component.datatable.DataTableRenderer.encodeMarkup(DataTableRenderer.java:407) at org.primefaces.component.datatable.DataTableRenderer.encodeEnd(DataTableRenderer.java:193) at javax.faces.component.UIComponentBase.encodeEnd(UIComponentBase.java:878) at org.primefaces.renderkit.CoreRenderer.renderChild(CoreRenderer.java:70) at org.primefaces.renderkit.CoreRenderer.renderChildren(CoreRenderer.java:54) at org.primefaces.component.tabview.TabViewRenderer.encodeContents(TabViewRenderer.java:198) at org.primefaces.component.tabview.TabViewRenderer.encodeMarkup(TabViewRenderer.java:130) at org.primefaces.component.tabview.TabViewRenderer.encodeEnd(TabViewRenderer.java:48) at javax.faces.component.UIComponentBase.encodeEnd(UIComponentBase.java:878) at javax.faces.component.UIComponent.encodeAll(UIComponent.java:1620) at javax.faces.render.Renderer.encodeChildren(Renderer.java:168) at javax.faces.component.UIComponentBase.encodeChildren(UIComponentBase.java:848) at javax.faces.component.UIComponent.encodeAll(UIComponent.java:1613) at javax.faces.component.UIComponent.encodeAll(UIComponent.java:1616) at javax.faces.component.UIComponent.encodeAll(UIComponent.java:1616) at com.sun.faces.application.view.FaceletViewHandlingStrategy.renderView(FaceletViewHandlingStrategy.java:380) at com.sun.faces.application.view.MultiViewHandler.renderView(MultiViewHandler.java:126) at com.sun.faces.lifecycle.RenderResponsePhase.execute(RenderResponsePhase.java:127) at com.sun.faces.lifecycle.Phase.doPhase(Phase.java:101) at com.sun.faces.lifecycle.LifecycleImpl.render(LifecycleImpl.java:139) at javax.faces.webapp.FacesServlet.service(FacesServlet.java:313) at org.apache.catalina.core.StandardWrapper.service(StandardWrapper.java:1523) at org.apache.catalina.core.ApplicationDispatcher.doInvoke(ApplicationDispatcher.java:802) at org.apache.catalina.core.ApplicationDispatcher.invoke(ApplicationDispatcher.java:664) at org.apache.catalina.core.ApplicationDispatcher.processRequest(ApplicationDispatcher.java:497) at org.apache.catalina.core.ApplicationDispatcher.doDispatch(ApplicationDispatcher.java:468) at org.apache.catalina.core.ApplicationDispatcher.dispatch(ApplicationDispatcher.java:364) at org.apache.catalina.core.ApplicationDispatcher.forward(ApplicationDispatcher.java:314) at org.apache.jasper.runtime.PageContextImpl.forward(PageContextImpl.java:783) at org.apache.jsp.welcome_jsp._jspService(welcome_jsp.java from :59) at org.apache.jasper.runtime.HttpJspBase.service(HttpJspBase.java:109) at javax.servlet.http.HttpServlet.service(HttpServlet.java:847) at org.apache.jasper.servlet.JspServletWrapper.service(JspServletWrapper.java:406) at org.apache.jasper.servlet.JspServlet.serviceJspFile(JspServlet.java:483) at org.apache.jasper.servlet.JspServlet.service(JspServlet.java:373) at javax.servlet.http.HttpServlet.service(HttpServlet.java:847) at org.apache.catalina.core.StandardWrapper.service(StandardWrapper.java:1523) at org.apache.catalina.core.StandardWrapperValve.invoke(StandardWrapperValve.java:279) at org.apache.catalina.core.StandardContextValve.invoke(StandardContextValve.java:188) at org.apache.catalina.core.StandardPipeline.invoke(StandardPipeline.java:641) at com.sun.enterprise.web.WebPipeline.invoke(WebPipeline.java:97) at com.sun.enterprise.web.PESessionLockingStandardPipeline.invoke(PESessionLockingStandardPipeline.java:85) at org.apache.catalina.core.StandardHostValve.invoke(StandardHostValve.java:185) at org.apache.catalina.connector.CoyoteAdapter.doService(CoyoteAdapter.java:332) at org.apache.catalina.connector.CoyoteAdapter.service(CoyoteAdapter.java:233) at com.sun.enterprise.v3.services.impl.ContainerMapper.service(ContainerMapper.java:165) at com.sun.grizzly.http.ProcessorTask.invokeAdapter(ProcessorTask.java:791) at com.sun.grizzly.http.ProcessorTask.doProcess(ProcessorTask.java:693) at com.sun.grizzly.http.ProcessorTask.process(ProcessorTask.java:954) at com.sun.grizzly.http.DefaultProtocolFilter.execute(DefaultProtocolFilter.java:170) at com.sun.grizzly.DefaultProtocolChain.executeProtocolFilter(DefaultProtocolChain.java:135) at com.sun.grizzly.DefaultProtocolChain.execute(DefaultProtocolChain.java:102) at com.sun.grizzly.DefaultProtocolChain.execute(DefaultProtocolChain.java:88) at com.sun.grizzly.http.HttpProtocolChain.execute(HttpProtocolChain.java:76) at com.sun.grizzly.ProtocolChainContextTask.doCall(ProtocolChainContextTask.java:53) at com.sun.grizzly.SelectionKeyContextTask.call(SelectionKeyContextTask.java:57) at com.sun.grizzly.ContextTask.run(ContextTask.java:69) at com.sun.grizzly.util.AbstractThreadPool$Worker.doWork(AbstractThreadPool.java:330) at com.sun.grizzly.util.AbstractThreadPool$Worker.run(AbstractThreadPool.java:309) at java.lang.Thread.run(Thread.java:619)

  Read the article

• Avoid generating empty STDOUT and STDERR files with Sun Grid Engine (SGE) and array jobs

  - by vy32

  I am running array jobs with Sun Grid Engine (SGE). My carefully scripted array job workers generate no stdout and no stderr when they function properly. Unfortunately, SGE insists on creating an empty stdout and stderr file for each run. Sun's manual states: STDOUT and STDERR of array job tasks will be written into dif- ferent files with the default location .['e'|'o']'.' In order to change this default, the -e and -o options (see above) can be used together with the pseudo-environment-vari- ables $HOME, $USER, $JOB_ID, $JOB_NAME, $HOSTNAME, and $SGE_TASK_ID. Note, that you can use the output redirection to divert the out- put of all tasks into the same file, but the result of this is undefined. I would like to have the output files suppressed if they are empty. Is there any way to do this?

  Read the article

• .apk signing fails even with Sun JDK (java.lang.NoClassDefFoundError: com.android.jarutils.DebugKeyP

  - by ianweller

  I'm having an interesting problem signing my Android application, whether or not I'm using a debug key. Regardless of the JDK I have installed to /usr/bin/{java,keytool,jarsigner} (OpenJDK or Sun's JDK) it will always give the following output after compiling successfully: -package-debug-sign: [apkbuilder] Creating RemoteNotify-debug-unaligned.apk and signing it with a debug key... BUILD FAILED /home/ianweller/AndroidSDK/platforms/android-7/templates/android_rules.xml:281: The following error occurred while executing this line: /home/ianweller/AndroidSDK/platforms/android-7/templates/android_rules.xml:152: java.lang.NoClassDefFoundError: com.android.jarutils.DebugKeyProvider The application was built and signed just fine by Eclipse with the ADT plugin (even without Sun's JDK installed). I'm on Fedora 12. I'm wanting to get my code out of Eclipse and move it into a git repository, but being unable to build it from ant will not allow this to happen.

  Read the article

• do not use com.sun.xml.internal.*?

  - by sarah xia

  Hi all, Is this statement true: com.sun.xml.internal package is an internal package as the name suggestes. Users should not write code that depends on internal JDK implementation classes. Such classes are internal implementation details of the JDK and subject to change without notice One of my colleagues used one of the classes in his code, which caused javac task in Ant fail to compile our project as the compiler couldn't find the class. Answer from Sun/Oracle says that this is expected behavior of the compiler as user shouldn't use the package. Question is why the classes in the package made public in the first place? Thanks, Sarah

  Read the article

• SPARC T5-4 LDoms for RAC and WebLogic Clusters

  - by Jeff Taylor-Oracle

  I wanted to use two Oracle SPARC T5-4 servers to simultaneously host both Oracle RAC and a WebLogic Server Cluster. I chose to use Oracle VM Server for SPARC to create a cluster like this: There are plenty of trade offs and decisions that need to be made, for example: Rather than configuring the system by hand, you might want to use an Oracle SuperCluster T5-8 My configuration is similar to jsavit's: Availability Best Practices - Example configuring a T5-8 but I chose to ignore some of the advice. Maybe I should have included an  alternate service domain, but I decided that I already had enough redundancy Both Oracle SPARC T5-4 servers were to be configured like this: Cntl 0.25  4  64GB                     App LDom                    2.75 CPU's                                        44 cores                                          704 GB              DB LDom      One CPU         16 cores         256 GB   The systems started with everything in the primary domain: # ldm list NAME             STATE      FLAGS   CONS    VCPU  MEMORY   UTIL  NORM  UPTIME primary          active     -n-c--  UART    512   1023G    0.0%  0.0%  11m # ldm list-spconfig factory-default [current] primary # ldm list -o core,memory,physio NAME              primary           CORE     CID    CPUSET     0      (0, 1, 2, 3, 4, 5, 6, 7)     1      (8, 9, 10, 11, 12, 13, 14, 15)     2      (16, 17, 18, 19, 20, 21, 22, 23) -- SNIP     62     (496, 497, 498, 499, 500, 501, 502, 503)     63     (504, 505, 506, 507, 508, 509, 510, 511) MEMORY     RA               PA               SIZE                 0x30000000       0x30000000       255G     0x80000000000    0x80000000000    256G     0x100000000000   0x100000000000   256G     0x180000000000   0x180000000000   256G # Give this memory block to the DB LDom IO     DEVICE                           PSEUDONYM        OPTIONS     pci@300                          pci_0                pci@340                          pci_1                pci@380                          pci_2                pci@3c0                          pci_3                pci@400                          pci_4                pci@440                          pci_5                pci@480                          pci_6                pci@4c0                          pci_7                pci@300/pci@1/pci@0/pci@6        /SYS/RCSA/PCIE1     pci@300/pci@1/pci@0/pci@c        /SYS/RCSA/PCIE2     pci@300/pci@1/pci@0/pci@4/pci@0/pci@c /SYS/MB/SASHBA0     pci@300/pci@1/pci@0/pci@4/pci@0/pci@8 /SYS/RIO/NET0        pci@340/pci@1/pci@0/pci@6        /SYS/RCSA/PCIE3     pci@340/pci@1/pci@0/pci@c        /SYS/RCSA/PCIE4     pci@380/pci@1/pci@0/pci@a        /SYS/RCSA/PCIE9     pci@380/pci@1/pci@0/pci@4        /SYS/RCSA/PCIE10     pci@3c0/pci@1/pci@0/pci@e        /SYS/RCSA/PCIE11     pci@3c0/pci@1/pci@0/pci@8        /SYS/RCSA/PCIE12     pci@400/pci@1/pci@0/pci@e        /SYS/RCSA/PCIE5     pci@400/pci@1/pci@0/pci@8        /SYS/RCSA/PCIE6     pci@440/pci@1/pci@0/pci@e        /SYS/RCSA/PCIE7     pci@440/pci@1/pci@0/pci@8        /SYS/RCSA/PCIE8     pci@480/pci@1/pci@0/pci@a        /SYS/RCSA/PCIE13     pci@480/pci@1/pci@0/pci@4        /SYS/RCSA/PCIE14     pci@4c0/pci@1/pci@0/pci@8        /SYS/RCSA/PCIE15     pci@4c0/pci@1/pci@0/pci@4        /SYS/RCSA/PCIE16     pci@4c0/pci@1/pci@0/pci@c/pci@0/pci@c /SYS/MB/SASHBA1     pci@4c0/pci@1/pci@0/pci@c/pci@0/pci@4 /SYS/RIO/NET2    Added an additional service processor configuration: # ldm add-spconfig split # ldm list-spconfig factory-default primary split [current] And removed many of the resources from the primary domain: # ldm start-reconf primary # ldm set-core 4 primary # ldm set-memory 32G primary # ldm rm-io pci@340 primary # ldm rm-io pci@380 primary # ldm rm-io pci@3c0 primary # ldm rm-io pci@400 primary # ldm rm-io pci@440 primary # ldm rm-io pci@480 primary # ldm rm-io pci@4c0 primary # init 6 Needed to add resources to the guest domains: # ldm add-domain db # ldm set-core cid=`seq -s"," 48 63` db # ldm add-memory mblock=0x180000000000:256G db # ldm add-io pci@480 db # ldm add-io pci@4c0 db # ldm add-domain app # ldm set-core 44 app # ldm set-memory 704G  app # ldm add-io pci@340 app # ldm add-io pci@380 app # ldm add-io pci@3c0 app # ldm add-io pci@400 app # ldm add-io pci@440 app Needed to set up services: # ldm add-vds primary-vds0 primary # ldm add-vcc port-range=5000-5100 primary-vcc0 primary Needed to add a virtual network port for the WebLogic application domain: # ipadm NAME              CLASS/TYPE STATE        UNDER      ADDR lo0               loopback   ok           --         --    lo0/v4         static     ok           --         ...    lo0/v6         static     ok           --         ... net0              ip         ok           --         ...    net0/v4        static     ok           --         xxx.xxx.xxx.xxx/24    net0/v6        addrconf   ok           --         ....    net0/v6        addrconf   ok           --         ... net8              ip         ok           --         --    net8/v4        static     ok           --         ... # dladm show-phys LINK              MEDIA                STATE      SPEED  DUPLEX    DEVICE net1              Ethernet             unknown    0      unknown   ixgbe1 net0              Ethernet             up         1000   full      ixgbe0 net8              Ethernet             up         10     full      usbecm2 # ldm add-vsw net-dev=net0 primary-vsw0 primary # ldm add-vnet vnet1 primary-vsw0 app Needed to add a virtual disk to the WebLogic application domain: # format Searching for disks...done AVAILABLE DISK SELECTIONS:        0. c0t5000CCA02505F874d0 <HITACHI-H106060SDSUN600G-A2B0-558.91GB>           /scsi_vhci/disk@g5000cca02505f874           /dev/chassis/SPARC_T5-4.AK00084038/SYS/SASBP0/HDD0/disk        1. c0t5000CCA02506C468d0 <HITACHI-H106060SDSUN600G-A2B0-558.91GB>           /scsi_vhci/disk@g5000cca02506c468           /dev/chassis/SPARC_T5-4.AK00084038/SYS/SASBP0/HDD1/disk        2. c0t5000CCA025067E5Cd0 <HITACHI-H106060SDSUN600G-A2B0-558.91GB>           /scsi_vhci/disk@g5000cca025067e5c           /dev/chassis/SPARC_T5-4.AK00084038/SYS/SASBP0/HDD2/disk        3. c0t5000CCA02506C258d0 <HITACHI-H106060SDSUN600G-A2B0-558.91GB>           /scsi_vhci/disk@g5000cca02506c258           /dev/chassis/SPARC_T5-4.AK00084038/SYS/SASBP0/HDD3/disk Specify disk (enter its number): ^C # ldm add-vdsdev /dev/dsk/c0t5000CCA02506C468d0s2 HDD1@primary-vds0 # ldm add-vdisk HDD1 HDD1@primary-vds0 app Add some additional spice to the pot: # ldm set-variable auto-boot\\?=false db # ldm set-variable auto-boot\\?=false app # ldm set-var boot-device=HDD1 app Bind the logical domains: # ldm bind db # ldm bind app At the end of the process, the system is set up like this: # ldm list -o core,memory,physio NAME             primary          CORE     CID    CPUSET     0      (0, 1, 2, 3, 4, 5, 6, 7)     1      (8, 9, 10, 11, 12, 13, 14, 15)     2      (16, 17, 18, 19, 20, 21, 22, 23)     3      (24, 25, 26, 27, 28, 29, 30, 31) MEMORY     RA               PA               SIZE                0x30000000       0x30000000       32G IO     DEVICE                           PSEUDONYM        OPTIONS     pci@300                          pci_0               pci@300/pci@1/pci@0/pci@6        /SYS/RCSA/PCIE1     pci@300/pci@1/pci@0/pci@c        /SYS/RCSA/PCIE2     pci@300/pci@1/pci@0/pci@4/pci@0/pci@c /SYS/MB/SASHBA0     pci@300/pci@1/pci@0/pci@4/pci@0/pci@8 /SYS/RIO/NET0   ------------------------------------------------------------------------------ NAME             app              CORE     CID    CPUSET     4      (32, 33, 34, 35, 36, 37, 38, 39)     5      (40, 41, 42, 43, 44, 45, 46, 47)     6      (48, 49, 50, 51, 52, 53, 54, 55)     7      (56, 57, 58, 59, 60, 61, 62, 63)     8      (64, 65, 66, 67, 68, 69, 70, 71)     9      (72, 73, 74, 75, 76, 77, 78, 79)     10     (80, 81, 82, 83, 84, 85, 86, 87)     11     (88, 89, 90, 91, 92, 93, 94, 95)     12     (96, 97, 98, 99, 100, 101, 102, 103)     13     (104, 105, 106, 107, 108, 109, 110, 111)     14     (112, 113, 114, 115, 116, 117, 118, 119)     15     (120, 121, 122, 123, 124, 125, 126, 127)     16     (128, 129, 130, 131, 132, 133, 134, 135)     17     (136, 137, 138, 139, 140, 141, 142, 143)     18     (144, 145, 146, 147, 148, 149, 150, 151)     19     (152, 153, 154, 155, 156, 157, 158, 159)     20     (160, 161, 162, 163, 164, 165, 166, 167)     21     (168, 169, 170, 171, 172, 173, 174, 175)     22     (176, 177, 178, 179, 180, 181, 182, 183)     23     (184, 185, 186, 187, 188, 189, 190, 191)     24     (192, 193, 194, 195, 196, 197, 198, 199)     25     (200, 201, 202, 203, 204, 205, 206, 207)     26     (208, 209, 210, 211, 212, 213, 214, 215)     27     (216, 217, 218, 219, 220, 221, 222, 223)     28     (224, 225, 226, 227, 228, 229, 230, 231)     29     (232, 233, 234, 235, 236, 237, 238, 239)     30     (240, 241, 242, 243, 244, 245, 246, 247)     31     (248, 249, 250, 251, 252, 253, 254, 255)     32     (256, 257, 258, 259, 260, 261, 262, 263)     33     (264, 265, 266, 267, 268, 269, 270, 271)     34     (272, 273, 274, 275, 276, 277, 278, 279)     35     (280, 281, 282, 283, 284, 285, 286, 287)     36     (288, 289, 290, 291, 292, 293, 294, 295)     37     (296, 297, 298, 299, 300, 301, 302, 303)     38     (304, 305, 306, 307, 308, 309, 310, 311)     39     (312, 313, 314, 315, 316, 317, 318, 319)     40     (320, 321, 322, 323, 324, 325, 326, 327)     41     (328, 329, 330, 331, 332, 333, 334, 335)     42     (336, 337, 338, 339, 340, 341, 342, 343)     43     (344, 345, 346, 347, 348, 349, 350, 351)     44     (352, 353, 354, 355, 356, 357, 358, 359)     45     (360, 361, 362, 363, 364, 365, 366, 367)     46     (368, 369, 370, 371, 372, 373, 374, 375)     47     (376, 377, 378, 379, 380, 381, 382, 383) MEMORY     RA               PA               SIZE                0x30000000       0x830000000      192G     0x4000000000     0x80000000000    256G     0x8080000000     0x100000000000   256G IO     DEVICE                           PSEUDONYM        OPTIONS     pci@340                          pci_1               pci@380                          pci_2               pci@3c0                          pci_3               pci@400                          pci_4               pci@440                          pci_5               pci@340/pci@1/pci@0/pci@6        /SYS/RCSA/PCIE3     pci@340/pci@1/pci@0/pci@c        /SYS/RCSA/PCIE4     pci@380/pci@1/pci@0/pci@a        /SYS/RCSA/PCIE9     pci@380/pci@1/pci@0/pci@4        /SYS/RCSA/PCIE10     pci@3c0/pci@1/pci@0/pci@e        /SYS/RCSA/PCIE11     pci@3c0/pci@1/pci@0/pci@8        /SYS/RCSA/PCIE12     pci@400/pci@1/pci@0/pci@e        /SYS/RCSA/PCIE5     pci@400/pci@1/pci@0/pci@8        /SYS/RCSA/PCIE6     pci@440/pci@1/pci@0/pci@e        /SYS/RCSA/PCIE7     pci@440/pci@1/pci@0/pci@8        /SYS/RCSA/PCIE8 ------------------------------------------------------------------------------ NAME             db               CORE     CID    CPUSET     48     (384, 385, 386, 387, 388, 389, 390, 391)     49     (392, 393, 394, 395, 396, 397, 398, 399)     50     (400, 401, 402, 403, 404, 405, 406, 407)     51     (408, 409, 410, 411, 412, 413, 414, 415)     52     (416, 417, 418, 419, 420, 421, 422, 423)     53     (424, 425, 426, 427, 428, 429, 430, 431)     54     (432, 433, 434, 435, 436, 437, 438, 439)     55     (440, 441, 442, 443, 444, 445, 446, 447)     56     (448, 449, 450, 451, 452, 453, 454, 455)     57     (456, 457, 458, 459, 460, 461, 462, 463)     58     (464, 465, 466, 467, 468, 469, 470, 471)     59     (472, 473, 474, 475, 476, 477, 478, 479)     60     (480, 481, 482, 483, 484, 485, 486, 487)     61     (488, 489, 490, 491, 492, 493, 494, 495)     62     (496, 497, 498, 499, 500, 501, 502, 503)     63     (504, 505, 506, 507, 508, 509, 510, 511) MEMORY     RA               PA               SIZE                0x80000000       0x180000000000   256G IO     DEVICE                           PSEUDONYM        OPTIONS     pci@480                          pci_6               pci@4c0                          pci_7               pci@480/pci@1/pci@0/pci@a        /SYS/RCSA/PCIE13     pci@480/pci@1/pci@0/pci@4        /SYS/RCSA/PCIE14     pci@4c0/pci@1/pci@0/pci@8        /SYS/RCSA/PCIE15     pci@4c0/pci@1/pci@0/pci@4        /SYS/RCSA/PCIE16     pci@4c0/pci@1/pci@0/pci@c/pci@0/pci@c /SYS/MB/SASHBA1     pci@4c0/pci@1/pci@0/pci@c/pci@0/pci@4 /SYS/RIO/NET2   Start the domains: # ldm start app LDom app started # ldm start db LDom db started Make sure to start the vntsd service that was created, above. # svcs -a | grep ldo disabled        8:38:38 svc:/ldoms/vntsd:default online          8:38:58 svc:/ldoms/agents:default online          8:39:25 svc:/ldoms/ldmd:default # svcadm enable vntsd Now use the MAC address to configure the Solaris 11 Automated Installation. Database Logical Domain # telnet localhost 5000 {0} ok devalias screen                   /pci@4c0/pci@1/pci@0/pci@c/pci@0/pci@7/display@0 disk7                    /pci@4c0/pci@1/pci@0/pci@c/pci@0/pci@c/scsi@0/disk@p3 disk6                    /pci@4c0/pci@1/pci@0/pci@c/pci@0/pci@c/scsi@0/disk@p2 disk5                    /pci@4c0/pci@1/pci@0/pci@c/pci@0/pci@c/scsi@0/disk@p1 disk4                    /pci@4c0/pci@1/pci@0/pci@c/pci@0/pci@c/scsi@0/disk@p0 scsi1                    /pci@4c0/pci@1/pci@0/pci@c/pci@0/pci@c/scsi@0 net3                     /pci@4c0/pci@1/pci@0/pci@c/pci@0/pci@4/network@0,1 net2                     /pci@4c0/pci@1/pci@0/pci@c/pci@0/pci@4/network@0 virtual-console          /virtual-devices/console@1 name                     aliases {0} ok boot net2 Boot device: /pci@4c0/pci@1/pci@0/pci@c/pci@0/pci@4/network@0  File and args: 1000 Mbps full duplex Link up Requesting Internet Address for xx:xx:xx:xx:xx:xx Requesting Internet Address for xx:xx:xx:xx:xx:xx WLS Logical Domain # telnet localhost 5001 {0} ok devalias hdd1                     /virtual-devices@100/channel-devices@200/disk@0 vnet1                    /virtual-devices@100/channel-devices@200/network@0 net                      /virtual-devices@100/channel-devices@200/network@0 disk                     /virtual-devices@100/channel-devices@200/disk@0 virtual-console          /virtual-devices/console@1 name                     aliases {0} ok boot net Boot device: /virtual-devices@100/channel-devices@200/network@0  File and args: Requesting Internet Address for xx:xx:xx:xx:xx:xx Requesting Internet Address for xx:xx:xx:xx:xx:xx Repeat the process for the second SPARC T5-4, install Solaris, RAC and WebLogic Cluster, and you are ready to go. Maybe buying a SuperCluster would have been easier.

  Read the article

• MSDTC failed in windows cluster any idea???

  - by Cute

  Hi I have created a windows2003 cluster and then try to configure MSDTC by following the link http://support.microsoft.com/kb/301600/#appliesto after follow this i have enable network DTC access in Windows Server 2003 by following http://support.microsoft.com/kb/817064/ But the group i have created MSDTC( as said in first link from 7th point onwards ) for the resourse Distribution Transaction Coordinator failed and all are in online after done this. But i dont know why it is failing.. I dont know how to post the screen shot here.....

  Read the article

• Application to test a cluster/grid

  - by Mystic

  Is anyone aware of any application (computation + data) that I can download to test an in-house grid middleware that will run on a local cluster. I hope to compare the performance with other available grid systems.

  Read the article

• MSDTC failed in windows cluster any idea?

  - by Cute

  I have created a windows2003 cluster and then try to configure MSDTC by following the link http://support.microsoft.com/kb/301600/#appliesto after follow this i have enable network DTC access in Windows Server 2003 by following http://support.microsoft.com/kb/817064/ But the group i have created MSDTC( as said in first link from 7th point onwards ) for the resourse Distribution Transaction Coordinator failed and all are in online after done this. But i dont know why it is failing.. I dont know how to post the screen shot here.....

  Read the article

• Change block/cluster size in unattend.xml

  - by ANervousTwitch

  Is there a way to change the block/cluster size when formatting a disk using unattend.xml & Windows Deployment Services? It keeps defaulting to 1024k, and I need something smaller.

  Read the article

• Utilizing 5 physical servers in 1 cluster

  - by Vijay Gharge

  Hi, I have 5 physical servers with low end memory & cpu resources. I want to create 1 cluster using all these servers and want to run mysql db on the same such that mysql db would utilize 5 server's CPU power to execute db queries & same for memory. Could you please help me understanding how to achieve this? Regards,

  Read the article

• Blocking IP addresses Load Balanced Cluster

  - by Dom

  Hi We're using HAproxy as a front end load balancer / proxy and are looking for solutions to block random IP addresses from jamming the cluster. Is anyone familiar with a conf for HAProxy that can block requests if they exceed a certain threshold from a single IP within a defined period of time. Or can anyone suggest a software solution which could be placed in front of HAProxy to handle this kind of blocking. Thanks Dom--

  Read the article

• EL FUTURO DEL CLOUD, A DEBATE EN EL XX CONGRESO NACIONAL DE USUARIOS ORACLE

  - by comunicacion-es_es(at)oracle.com

  Normal 0 21 false false false ES X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin-top:0cm; mso-para-margin-right:0cm; mso-para-margin-bottom:10.0pt; mso-para-margin-left:0cm; line-height:115%; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin;} ¡Vuelta a un mini Oracle OpenWorld! La Comunidad de Usuarios de Oracle celebrará en Madrid los próximos 16 y 17 de marzo su XX Congreso Nacional, donde estarán representadas TODAS las áreas de Oracle (aplicaciones, tecnología, hardware y canal). Bajo el lema "Agilidad, innovación y optimización del negocio", contaremos con prestigiosos ponentes internacionales como Massimo Pezzini, vicepresidente de Gartner; Rex Wang, experto en Cloud Computing y vicepresidente de marketing de producto de Oracle; y Janny Ekelson, director de aplicaciones y arquitectura FedEx Express Europa. A parte de los más de 15 casos de éxito, en las más de 40 presentaciones programadas, el Cloud Computing será uno de los temas estrella junto a la estrategia en hardware de Oracle tras la adquisición de Sun. ¡Os esperamos!

  Read the article

• Oracle Solaris Zones Physical to virtual (P2V)

  - by user939057

  IntroductionThis document describes the process of creating and installing a Solaris 10 image build from physical system and migrate it into a virtualized operating system environment using the Oracle Solaris 10 Zones Physical-to-Virtual (P2V) capability.Using an example and various scenarios, this paper describes how to take advantage of theOracle Solaris 10 Zones Physical-to-Virtual (P2V) capability with other Oracle Solaris features to optimize performance using the Solaris 10 resource management advanced storage management using Solaris ZFS plus improving operating system visibility with Solaris DTrace. The most common use for this tool is when performing consolidation of existing systems onto virtualization enabled platforms, in addition to that we can use the Physical-to-Virtual (P2V) capability  for other tasks for example backup your physical system and move them into virtualized operating system environment hosted on the Disaster Recovery (DR) site another option can be building an Oracle Solaris 10 image repository with various configuration and a different software packages in order to reduce provisioning time.Oracle Solaris ZonesOracle Solaris Zones is a virtualization and partitioning technology supported on Oracle Sun servers powered by SPARC and Intel processors.This technology provides an isolated and secure environment for running applications. A zone is a virtualized operating system environment created within a single instance of the Solaris 10 Operating System.Each virtual system is called a zone and runs a unique and distinct copy of the Solaris 10 operating system.Oracle Solaris Zones Physical-to-Virtual (P2V)A new feature for Solaris 10 9/10.This feature provides the ability to build a Solaris 10 images from physical system and migrate it into a virtualized operating system environmentThere are three main steps using this tool1. Image creation on the source system, this image includes the operating system and optionally the software in which we want to include within the image. 2. Preparing the target system by configuring a new zone that will host the new image.3. Image installation on the target system using the image we created on step 1. The host, where the image is built, is referred to as the source system and the host, where theimage is installed, is referred to as the target system. Benefits of Oracle Solaris Zones Physical-to-Virtual (P2V)Here are some benefits of this new feature:  Simple- easy build process using Oracle Solaris 10 built-in commands.  Robust- based on Oracle Solaris Zones a robust and well known virtualization technology.  Flexible- support migration between V series servers into T or -M-series systems.For the latest server information, refer to the Sun Servers web page. PrerequisitesThe target Oracle Solaris system should be running the latest version of the patching patch cluster. and the minimum Solaris version on the target system should be Solaris 10 9/10.Refer to the latest Administration Guide for Oracle Solaris for a complete procedure on how todownload and install Oracle Solaris. NOTE: If the source system that used to build the image is an older version then the targetsystem, then during the process, the operating system will be upgraded to Solaris 10 9/10(update on attach).Creating the Image Used to distribute the software.We will create an image on the source machine. We can create the image on the local file system and then transfer it to the target machine, or build it into a NFS shared storage andmount the NFS file system from the target machine.Optional  before creating the image we need to complete the software installation that we want to include with the Solaris 10 image.An image is created by using the flarcreate command:Source # flarcreate -S -n s10-system -L cpio /var/tmp/solaris_10_up9.flarThe command does the following:  -S specifies that we skip the disk space check and do not write archive size data to the archive (faster).  -n specifies the image name.  -L specifies the archive format (i.e cpio). Optionally, we can add descriptions to the archive identification section, which can help to identify the archive later.Source # flarcreate -S -n s10-system -e "Oracle Solaris with Oracle DB10.2.0.4" -a "oracle" -L cpio /var/tmp/solaris_10_up9.flarYou can see example of the archive identification section in Appendix A: archive identification section.We can compress the flar image using the gzip command or adding the -c option to the flarcreate commandSource # gzip /var/tmp/solaris_10_up9.flarAn md5 checksum can be created for the image in order to ensure no data tamperingSource # digest -v -a md5 /var/tmp/solaris_10_up9.flar Moving the image into the target system.If we created the image on the local file system, we need to transfer the flar archive from the source machine to the target machine.Source # scp /var/tmp/solaris_10_up9.flar target:/var/tmpConfiguring the Zone on the target systemAfter copying the software to the target machine, we need to configure a new zone in order to host the new image on that zone.To install the new zone on the target machine, first we need to configure the zone (for the full zone creation options see the following link: http://docs.oracle.com/cd/E18752_01/html/817-1592/index.html  )ZFS integrationA flash archive can be created on a system that is running a UFS or a ZFS root file system.NOTE: If you create a Solaris Flash archive of a Solaris 10 system that has a ZFS root, then bydefault, the flar will actually be a ZFS send stream, which can be used to recreate the root pool.This image cannot be used to install a zone. You must create the flar with an explicit cpio or paxarchive when the system has a ZFS root.Use the flarcreate command with the -L archiver option, specifying cpio or pax as themethod to archive the files. (For example, see Step 1 in the previous section).Optionally, on the target system you can create the zone root folder on a ZFS file system inorder to benefit from the ZFS features (clones, snapshots, etc...).Target # zpool create zones c2t2d0 Create the zone root folder:Target # chmod 700 /zones Target # zonecfg -z solaris10-up9-zonesolaris10-up9-zone: No such zone configuredUse 'create' to begin configuring a new zone.zonecfg:solaris10-up9-zone> createzonecfg:solaris10-up9-zone> set zonepath=/zoneszonecfg:solaris10-up9-zone> set autoboot=truezonecfg:solaris10-up9-zone> add netzonecfg:solaris10-up9-zone:net> set address=192.168.0.1zonecfg:solaris10-up9-zone:net> set physical=nxge0zonecfg:solaris10-up9-zone:net> endzonecfg:solaris10-up9-zone> verifyzonecfg:solaris10-up9-zone> commitzonecfg:solaris10-up9-zone> exit Installing the Zone on the target system using the imageInstall the configured zone solaris10-up9-zone by using the zoneadm command with the install -a option and the path to the archive.The following example shows how to create an Image and sys-unconfig the zone.Target # zoneadm -z solaris10-up9-zone install -u -a/var/tmp/solaris_10_up9.flarLog File: /var/tmp/solaris10-up9-zone.install_log.AJaGveInstalling: This may take several minutes...The following example shows how we can preserve system identity.Target # zoneadm -z solaris10-up9-zone install -p -a /var/tmp/solaris_10_up9.flar Resource management Some applications are sensitive to the number of CPUs on the target Zone. You need tomatch the number of CPUs on the Zone using the zonecfg command:zonecfg:solaris10-up9-zone>add dedicated-cpuzonecfg:solaris10-up9-zone> set ncpus=16DTrace integrationSome applications might need to be analyzing using DTrace on the target zone, you canadd DTrace support on the zone using the zonecfg command:zonecfg:solaris10-up9-zone>setlimitpriv="default,dtrace_proc,dtrace_user" Exclusive IP stack An Oracle Solaris Container running in Oracle Solaris 10 can have a shared IP stack with the global zone, or it can have an exclusive IP stack (which was released in Oracle Solaris 10 8/07). An exclusive IP stack provides a complete, tunable, manageable and independent networking stack to each zone. A zone with an exclusive IP stack can configure Scalable TCP (STCP), IP routing, IP multipathing, or IPsec. For an example of how to configure an Oracle Solaris zone with an exclusive IP stack, see the following example zonecfg:solaris10-up9-zone set ip-type=exclusivezonecfg:solaris10-up9-zone> add netzonecfg:solaris10-up9-zone> set physical=nxge0 When the installation completes, use the zoneadm list -i -v options to list the installedzones and verify the status.Target # zoneadm list -i -vSee that the new Zone status is installedID NAME STATUS PATH BRAND IP0 global running / native shared- solaris10-up9-zone installed /zones native sharedNow boot the ZoneTarget # zoneadm -z solaris10-up9-zone bootWe need to login into the Zone order to complete the zone set up or insert a sysidcfg file beforebooting the zone for the first time see example for sysidcfg file in Appendix B: sysidcfg filesectionTarget # zlogin -C solaris10-up9-zoneTroubleshootingIf an installation fails, review the log file. On success, the log file is in /var/log inside the zone. Onfailure, the log file is in /var/tmp in the global zone.If a zone installation is interrupted or fails, the zone is left in the incomplete state. Use uninstall -F to reset the zone to the configured state.Target # zoneadm -z solaris10-up9-zone uninstall -FTarget # zonecfg -z solaris10-up9-zone delete -FConclusionOracle Solaris Zones P2V tool provides the flexibility to build pre-configuredimages with different software configuration for faster deployment and server consolidation.In this document, I demonstrated how to build and install images and to integrate the images with other Oracle Solaris features like ZFS and DTrace.Appendix A: archive identification sectionWe can use the head -n 20 /var/tmp/solaris_10_up9.flar command in order to access theidentification section that contains the detailed description.Target # head -n 20 /var/tmp/solaris_10_up9.flarFlAsH-aRcHiVe-2.0section_begin=identificationarchive_id=e4469ee97c3f30699d608b20a36011befiles_archived_method=cpiocreation_date=20100901160827creation_master=mdet5140-1content_name=s10-systemcreation_node=mdet5140-1creation_hardware_class=sun4vcreation_platform=SUNW,T5140creation_processor=sparccreation_release=5.10creation_os_name=SunOScreation_os_version=Generic_142909-16files_compressed_method=nonecontent_architectures=sun4vtype=FULLsection_end=identificationsection_begin=predeploymentbegin 755 predeployment.cpio.ZAppendix B: sysidcfg file sectionTarget # cat sysidcfgsystem_locale=Ctimezone=US/Pacificterminal=xtermssecurity_policy=NONEroot_password=HsABA7Dt/0sXXtimeserver=localhostname_service=NONEnetwork_interface=primary {hostname= solaris10-up9-zonenetmask=255.255.255.0protocol_ipv6=nodefault_route=192.168.0.1}name_service=NONEnfs4_domain=dynamicWe need to copy this file before booting the zoneTarget # cp sysidcfg /zones/solaris10-up9-zone/root/etc/

  Read the article

• The Oracle EMEA Partner Event of the Year- FREE, LIVE & ONLINE!

  - by Claudia Costa

  New products. New specializations. New opportunities. Find out how you can use them to build your Oracle business even faster and more effectively in 2010/11. The date for your diary is the 29th of June 2010, at 11:00 GMT. And this summer's event is bigger and better than ever. You will learn: What Oracle's acquisition of Sun Microsystems means for your business and your customers How Oracle Specialization can help you grow faster and smarter, and how Oracle partners from across the region are already benefitting Why Oracle's latest technology, applications, middleware and hardware products and solutions offer you unbeatable new business opportunities How Oracle's partner program is evolving to help partners succeed with a live link to the Oracle FY11 Global Partner Kickoff How specialization has helped a former Microsoft executive become one of the world's most successful social entrepreneurs You'll also have the chance to network with Oracle experts and other partners, and download valuable collateral from specially constructed virtual information booths. Plus, at the end of the event, submit your feedback form for the chance to win two passes to Oracle OpenWorld in San Francisco this September! Don't miss out! REGISTER TODAY!  for this exciting, exclusive online event. Visit here for more information and to view the complete agenda We look forward to welcoming you on the 29th of June! Yours sincerely, Stein SurlienSenior Vice President, Alliances & Channels, Oracle EMEA PS. The Oracle PartnerNetwork Days Virtual Event will be followed by "Oracle PartnerNetwork Days Executive Forums", and "Oracle PartnerNetwork Days Satellite Events" in various countries. Please look out for further communications from your local Oracle team.

  Read the article

< Previous Page | 19 20 21 22 23 24 25 26 27 28 29 30  | Next Page >