Search Results

Search found 31410 results on 1257 pages for 'disk based'.

Page 230/1257 | < Previous Page | 226 227 228 229 230 231 232 233 234 235 236 237  | Next Page >

• Is putting swapfile & temp folder in ramdisk a good idea in Windows 7 64 bit with lots of ram?

  - by Tony_Henrich

  I want my Windows to run as fast as possible. If I have 12GB ram in Windows 7 64bit, quad core cpu, and all apps fit in memory, will the swap file ever be used for anything? The question is about if its a good idea to put the swap file in a ram disk. Would a ram disk help in any way or will Windows intelligently use all the available memory for all its work? I am also thinking of putting the temp folder in a ram disk. I know ram disk is volatile memory and I don't care about its content in it if it gets lost.

  Read the article

• Ubuntu 12.04 can't boot after installing with software RAID 1

  - by Bill

  I've been trying to install Ubuntu with software RAID on my server and there is obviously something that I don't understand about the process. This is the guide that I followed: https://help.ubuntu.com/11.04/serverguide/advanced-installation.html I have two identical 1 TB disks in my server. I went through the initial install process and manually set up my partitions. On each disk I set up: (1) 100 MB partition for EFI boot (I didn't originally have this but added it based on a forum post I found after my original install failed to boot, I ended up with EFIboot since that was what the 'guided partitioning' decided to do) (1) 970 MB partition for / (1) 30 MB partition for swap I then created new RAID 1 disks combining the two partitions, one from each disk, such that each partition is mirrored. I then configured their usage as stated above. After saving the configuration I said yes to boot in a degraded state. The rest of the setup went normally, no errors of any kind. I saw GRUB being installed and again no errors. However, after rebooting the server I get the dreaded 'Insert boot media' and nothing happens. I loaded up the recovery disk and the mdadm configuration looks correct. md0 is my EFIBoot partition md1 is my \ partition using ext4 md2 is my swap partition Running file -s /dev/md0 doesn't indicate that GRUB is there and so I attempted to reinstall GRUB using the recovery disk. I selected the md0 disk and it appeared to install just fine. Running file -s /dev/md1 shows the error needs journal recovery, I'm not sure if that's related or not or how to fix that. Rebooting gives me the same problem, no boot media found. I've searched around the internet but can't figure out what to do next or more importantly how to troubleshoot what exactly is going wrong. Thanks!

  Read the article

• Windows 8 Permissions

  - by Dane Balia

  I, 2 days ago, completed a standard Windows 8 installation. It was a fresh install, however Windows 7 was on the disk prior to which it migrated to Windows.old. But for some strange and weird reason, I am struggling to 'write' to my disk in regards to .NET Applications. It appears that none of my .NET (self-written) applications can write to their log files on disk, which are created on startup. I have disabled UAC, as well as set Full Control over Disk C: for my User, but no luck. I keep getting the error: A required privilege is not held by the client. I did google and try some online tuts - but no luck! Thanks

  Read the article

• Ubuntu server boot degraded raid

  - by beacon_bonanza

  I've installed Ubuntu 12.04.1 in a new server and set up the 4 hard drives with 3 RAID 1 devices, the configuration is such that the first two drives have md0 (swap space) and md1 (/) with the third and fourth drives having md2 (/var). I've been testing the operation under a drive failure and found that the system boots fine if I remove disk two but if I remove disk one then the system gets to grub and then just restarts. I'm confused as to why grub appears to be loading properly from disk two but then the boot fails.

  Read the article

• Windows 7: moved system partition, need to update boot partition

  - by Actorclavilis

  So, I have a decently standard Windows7/Ubuntu dual-boot setup, and (since Ubuntu is my usual operating system) I found I needed to grow my Ubuntu partition and shrink my W7 partition. Originally, my system (500G) looked like this: W7 Boot Partition (1.5G) Ubuntu (around 240G) W7 (same as Ubuntu) (on an extended partition, all by itself) Swap (rest of disk, around 16G) Now I'm no stranger to partitioning and filesystem tools, especially GParted, which I used on a Linux boot disk. After my partition editing, the partitions are laid out the same, except the Ubuntu partition is now 407G and the W7 partition is smaller to compensate. I had supposed, based on http://www.gparted.org/faq.php, that I would be able to run the W7 install disk in recovery mode and have it deal with the rearrangement, then possibly reinstall GRUB or something. Well, now the W7 install disk doesn't even see my W7 installation. All my files are there, the NTFS is perfectly clean, no problems there, but the install disk won't notice it. (Of course, the GRUB entry works fine but the W7 boot partition (which I didn't change) refuses to boot it.) So, basically, any ideas on how to fix this? I don't especially want to rerun the entire install procedure because I'll have a bunch of programs to reinstall (never mind redoing GRUB), but I fear that might be the only option. Thanks.

  Read the article

• How to fix windows 7 boot process

  - by MasterCorban

  Ok so i used xp for years before i was able to get my hands on the Windows7 RC which i bought a new HDD for, and then followed the process to dual-boot. About a month ago xp started acting funny and i thought the disk might be dying. So i started using Windows7 all the time. Today i start the computer and it cant find the disk which xp was on anymore. I guess its dead. So i remove the xp HD and my computer cant start...insert bootable disk or something similar So how can i remove the primary(dead) xp disk and boot straight to Windows 7?

  Read the article

• Can I lvreduce after lvextend without losing the ext4 partition inside it?

  - by DrSAR

  In a botched attempt to move my root partition from one disk to another I have done the following: added new disk partitioned it with parted (part #3 is now almost totally filling the disk) initialized a physical volume $ pvcreate /dev/sdb3 Physical volume "/dev/sdb3" successfully created extended the volume group to include this new physical disk $ vgextend myvg /dev/sdb3 Volume group "myvg" successfully extended extended the logical volume (I think this is where I ballsed it up: I think I should have pvmove'ed stuff to the new pv in that group - can someone confirm?) $ lvextend /dev/mapper/myvg-root /dev/sdb3 I would now like to undo the lvextend and then proceed with the original plan of moving the content of the old physical volume over to the new physical volume. Can I reduce the logical volume (I have not yet touched the ext4 partition that sits in /dev/mapper/myvg-root with something like resizefs) without fear of damaging the ext4 filesystem? If so, how do I tell it to reduce by exactly the right amount? $ lvreduce --by-exactly-the-amount-occupied-by-PV /ev/sdb3 /dev/mapper/myvg-root

  Read the article

• My external HD turned to RAW - How to recover my data?

  - by Matan Eldan

  I have an external HD (WD MyBook Essentials) with all of my backups (1TB) for some unknown reason, when I try to connect the drive (Tried several interfaces: eSATA/plugged it into my PC/USB) I get this message: "You need to format the disk in drive M: before you can use it" I've looked in disk management at the drive, and its listed in there - with the same full capacity. The file system under disk management now says RAW and that its healthy

  Read the article

• SATA disks boot order?

  - by kire

  I have a computer with 4 SATA disks connected, 2 to the motherboard and 2 to a PCI-card. I've moved all the disks from other computers so 2 of them already has windows installed, the other 2 has just had data on them. I know one of the windows installations works and i want to use this install. If i only have this disk connected the computer boots fine. The problem is that when i boot with all 4 disks connected i get an error message about not being able to boot. This message is in swedish(the wrong windows installation is swedish) so it has to come from that installation. Ok, that means it is trying to boot from wrong disk, i try to pull out that disk but then i get the same error in english. I pull out the fourth disk instead I get another error about NTLDR not being able to load. If i disconnect all drives except the one with the correct windows installation, windows boots fine and i can also connect the other drives while windows is running and browse around in them without any problems. I have no clue what to do. In my BIOS setup i can only select SATA as boot-option, not the order of the disks. I also tried to remove what's left of windows on the other disk by simply deleting everything in explorer(got hidden- and sytstem-files visible). Both windows installations are XP btw. Edit: I switched the cables around and now it magically works. :)

  Read the article

• Why will multiple dvd/cd-rom drives stop reading?

  - by ddc0660

  I'm having difficulty with two dvd/cd drives. When I updated from XP to Vista, I noticed they wouldn't work. I could add cds or dvds to the drives and they would attempt to read the disk, but never "found" a disk in the drive. Vista showed the drives existed without problems. I updated their drivers and nothing changed. I thought perhaps, oddly, both drives were going bad. Then I got Windows 7, and I figured I'd have to do some gymnastics in order to get it onto my system without a working disk drive. However, I can boot from the Windows 7 disk fine! I installed 7 hoping that it was a Vista problem and I'd reclaim my drives, but that is not the case. The same symptoms persist. Thoughts?

  Read the article

• 1TB HDD making strange noise (not a common one)

  - by Darkkurama

  I built a new PC some days ago, and everything seems perfect, except that the 1 TB HDD I cloned from my old 500 GB HDD is making a deep weird sound. First of all, every time I access the disk, I hear a deep sound, and when the PC is turning on, I hear some clicking (the rapid clicking is my mouse, I'm opening and closing folders to trigger the vibrating deep weird sound I'm describing). I'm using this 1TB disk for data mainly (I use a SSD as the OS). As background information, the disk is a seagate barracuda 7200 rpm which was RMAd and replaced with a refurbished one. Maybe the refurbished disks make these noises? should I worry about my data? (although the disk is working normal and passed a seagatetools short generic test? Thanks! PS: I recorded the sounds, just click on the links. Thanks

  Read the article

• SQL SERVER – Generate Report for Index Physical Statistics – SSMS

  - by pinaldave

  Few days ago, I wrote about SQL SERVER – Out of the Box – Activity and Performance Reports from SSSMS (Link). A user asked me a question regarding if we can use similar reports to get the detail about Indexes. Yes, it is possible to do the same. There are similar type of reports are available at Database level, just like those available at the Server Instance level. You can right click on Database name and click Reports. Under Standard Reports, you will find following reports. Disk Usage Disk Usage by Top Tables Disk Usage by Table Disk Usage by Partition Backup and Restore Events All Transactions All Blocking Transactions Top Transactions by Age Top Transactions by Blocked Transactions Count Top Transactions by Locks Count Resource Locking Statistics by Objects Object Execute Statistics Database Consistency history Index Usage Statistics Index Physical Statistics Schema Change history User Statistics Select the Reports with name Index Physical Statistics. Once click, a report containing all the index names along with other information related to index will be visible, e.g. Index Type and number of partitions. One column that caught my interest was Operation Recommended. In some place, it suggested that index needs to be rebuilt. It is also possible to click and expand the column of partitions and see additional details about index as well. DBA and Developers who just want to have idea about how your index is and its physical statistics can use this tool. Click to Enlarge Note: Please note that I will rebuild my indexes just because this report is recommending it. There are many other parameters you need to consider before rebuilding indexes. However, this tool gives you the accurate stats of your index and it can be right away exported to Excel or PDF writing by clicking on the report. Reference : Pinal Dave (http://blog.SQLAuthority.com) Filed under: Pinal Dave, SQL, SQL Authority, SQL Index, SQL Optimization, SQL Performance, SQL Query, SQL Server, SQL Server Management Studio, SQL Tips and Tricks, SQL Utility, T SQL, Technology

  Read the article

• Windows Embedded CE DiskPrep PowerToy

  - by Bruce Eitman

  Kurt Kennett from Microsoft has offered up a handy new tool. This tool is useful for creating a boot disk for x86 Windows CE systems that use the BIOSLoader. This is especially useful for creating disks with formats other than FAT16, which are fairly easy to create. I am letting you know about this new tool, but I have to be honest in telling you that I haven’t used it myself because it is for Windows Vista and Windows 7 – which I don’t have available right now. But you can bet that I will be setting up a virtual machine to give it a try. Here is what Kurt has to say about the tool: Download the DiskPrep Tool  DiskPrep can prepare any hard disk that can be attached to your development PC so that it can boot your X86-based Windows CE OS Design. USB disks (including disk "keys"), Compact Flash Cards, and SD cards all work if your system bios can boot from that type of media. FAT16, FAT32, and exFAT all supported. DOS is not used - the program prepares the bios loader on the disk and only uses that. If you use Windows Vista or Windows 7, you can use VHD files for VirtualPC. This allows for rapid prototyping of a self-booting system. Copyright © 2010 – Bruce Eitman All Rights Reserved

  Read the article

• How do I install GRUB on a RAID system installation?

  - by root45

  I'm trying to setup and install Ubuntu on a RAID 1 setup. I have two disks, sdb and sdc. I've been following this guide https://help.ubuntu.com/community/Installation/SoftwareRAID which more or less works for getting everything set up and Ubuntu installed. The problem is at the end of the installation, it tries to install GRUB. By default it tries my "first disk", which gives a "fatal error". I've tried installing it on a specific partion, e.g. sdb1 as well as RAID devices, e.g. md0, md1, etc.. Nothing seems to work. Edit: The actual error is "Unable to install GRUB in /dev/sdb Executing 'grub-install '/dev/sdb' failed. This is a fatal error." Then I'm taken back to the main install menu. If I choose "Install the GRUB boot loader on a hard disk" option, I can pick the partition, but entering sdb2 or md1 gives the same error. So I went ahead an just didn't install GRUB, which means now I presumably have a working Ubuntu installation, but I can't boot it. I've tried booting from the LiveCD to install GRUB, but I can't chroot into my system because it doesn't seem to recognize that my disk is a Linux disk. There's an error about it being a RAID partition. So basically I would really like to know how you know to which device to install GRUB at installation, or at the very least, how to install it on to my system now. I suppose I should also mention that sda is a Windows 7 installation that I would like to keep around and be able to access at boot. Thanks for any help.

  Read the article

• Persistence problem when installing USB Ubuntu variant using Windows

  - by Derek Redfern

  I'm part of a project called One2One2Go - we're developing a Live USB Ubuntu variant for use in schools in Somerville, MA. We have the project files compiled into an iso, and when installed using the native Ubuntu Startup Disk Creator, the USB works fine. When installed using a tool on a Windows machine (LiLi at linuxliveusb.com or liveusb-creator at fedorahosted.org/liveusb-creator), the USB works, but does not have persistence. This happens even if the creator is specifically set to allocate an area for persistent files. When comparing files on sticks created in Windows or Ubuntu, the one file that is different is syslinux/syslinux.cfg. I have printed the contents of the file below: Installed on Windows: DEFAULT nomodset LABEL debug menu label ^debug kernel /casper/vmlinuz append boot=casper xforcevesa initrd=/casper/initrd.gz -- LABEL nomodset menu label ^nomodset kernel /casper/vmlinuz append boot=casper quiet splash nomodset initrd=/casper/initrd.gz -- LABEL memtest menu label ^Memory test kernel /install/memtest append - LABEL hd menu label ^Boot from first hard disk localboot 0x80 append - PROMPT 0 TIMEOUT 1 Installed on Ubuntu: DEFAULT nomodset LABEL debug menu label ^debug kernel /casper/vmlinuz append noprompt cdrom-detect/try-usb=true persistent boot=casper xforcevesa initrd=/casper/initrd.gz -- LABEL nomodset menu label ^nomodset kernel /casper/vmlinuz append noprompt cdrom-detect/try-usb=true persistent boot=casper quiet splash nomodset initrd=/casper/initrd.gz -- LABEL memtest menu label ^Memory test kernel /install/memtest append - LABEL hd menu label ^Boot from first hard disk localboot 0x80 append - PROMPT 0 TIMEOUT 1 For troubleshooting reasons, I changed the Windows-created syslinux.cfg to match the one created by Ubuntu and persistence worked on it. I think the problem is that on the stick created by Windows, there is no "persistent" flag, but I don't know why. Is this a problem with our disk image or with the creator? How would I go about fixing this problem? Thanks in advance for your help. Derek Redfern

  Read the article

• How to start a task before networking?

  - by user1252434

  I've written an upstart task that modifies /etc/network/interfaces. (Actually a file sourced into it.) Which start on condition do I need to declare to let my task run before any networking jobs? I've tried start on starting networking, but that's apparently too late. When I log in after booting I can see that the changes were written, but obviously they are not used: the new config states a static IP, but the boot process waits for a non-existing DHCP server (old config) to time out. I've also tried start on starting network-interface INTERFACE=eth0, which didn't work either. IIRC there was an error in the log that the change couldn't be written. Background: I need a VM template that can be cloned and the clones configured through a script. Among other settings, I need to give them a static IP address to access them from the host. I use guestfish to write a config file to one of the virtual disks and let a script apply these settings to the system. I don't want that disk to contain an actual system settings file. I can't modify /etc directly, because that disk is shared (copy-on-write/diff) among the clones and guestfish apparently doesn't support that type of image. I could also let them use DHCP and setup a server that assigns IP by MAC, but I'm afraid of the complexity. I could also add just another virtual disk for configuration files, but if possible I'd prefer to store settings directly on the system disk image. Used software: Ubuntu Server 12.04, VirtualBox. The configuration modifier is a self written ruby script.

  Read the article

• Permission denied on /dev/xvdf despite sudo?

  - by Sid

  I'm trying to get a stream off port 9999 and write to /dev/xvdf. I'm using Amazon EC2 with the Ubuntu 11.10 server image. By default I log in as 'ubuntu' which has sudo privileges. However, when I run the following netcat command, I get this error ubuntu@ip-10-252-35-122:~$ ls -al /dev/xv* brw-rw---- 1 root disk 202, 1 2011-11-30 22:22 /dev/xvda1 brw-rw---- 1 root disk 202, 80 2011-11-30 22:27 /dev/xvdf ubuntu@ip-10-252-35-122:~$ sudo netcat -p 9999 -l > /dev/xvdf bash: /dev/xvdf: Permission denied ubuntu@ip-10-252-35-122:~$ Any idea why I get the permission denied error and how I can work around it? Update: Something mysterious is running in the background that resets the permissions? Check the snippet below and the permission flags seem to automatically reset when I try using /dev/xvdf !?! ubuntu@ip-10-252-35-122:~$ sudo chmod 777 /dev/xvdf ubuntu@ip-10-252-35-122:~$ ls -al /dev/xvdf brwxrwxrwx 1 root disk 202, 80 2011-11-30 22:43 /dev/xvdf ubuntu@ip-10-252-35-122:~$ sudo nc -p 9999 -l > /dev/xvdf This is nc from the netcat-openbsd package. An alternative nc is available in the netcat-traditional package. usage: nc [-46DdhklnrStUuvzC] [-i interval] [-P proxy_username] [-p source_port] [-s source_ip_address] [-T ToS] [-w timeout] [-X proxy_protocol] [-x proxy_address[:port]] [hostname] [port[s]] ubuntu@ip-10-252-35-122:~$ ls -al /dev/xvdf brw-rw---- 1 root disk 202, 80 2011-11-30 22:43 /dev/xvdf ubuntu@ip-10-252-35-122:~$ I'm using stock Ubuntu Amazon EC2 images from http://alestic.com/ (links to images at the top)

  Read the article

• SD-CARD reader does not show in ubuntu

  - by shantanu

  I bought Acer asipre 4250. It have built-in SD card reader. But it is not working. Nothing show in /media or fdisk but something in dmesg. dmesg: new high-speed USB device number 3 using ehci_hcd [ 127.396733] scsi5 : usb-storage 2-2:1.0 [ 128.526562] scsi 5:0:0:0: Direct-Access Multiple Card Reader 1.00 PQ: 0 ANSI: 0 [ 128.532512] sd 5:0:0:0: Attached scsi generic sg2 type 0 [ 129.008110] ohci_hcd 0000:00:12.0: PCI INT A disabled [ 129.032083] ohci_hcd 0000:00:13.0: PCI INT A disabled [ 129.056411] ohci_hcd 0000:00:16.0: PCI INT A disabled [ 129.338026] sd 5:0:0:0: [sdb] Attached SCSI removable disk [ 129.808328] ohci_hcd 0000:00:14.5: PCI INT C disabled [ 167.728616] usb 2-2: USB disconnect, device number 3 [ 169.872284] ehci_hcd 0000:00:13.2: PCI INT B disabled [ 169.872340] ehci_hcd 0000:00:13.2: PME# enabled fdisk -l: Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x0006bc6d Device Boot Start End Blocks Id System /dev/sda1 * 2048 48828415 24413184 7 HPFS/NTFS/exFAT /dev/sda2 48828416 50829311 1000448 82 Linux swap / Solaris /dev/sda3 50829312 99657727 24414208 83 Linux /dev/sda4 99659774 625141759 262740993 5 Extended Partition 4 does not start on physical sector boundary. /dev/sda5 99659776 275439615 87889920 7 HPFS/NTFS/exFAT /dev/sda6 275441664 451221503 87889920 7 HPFS/NTFS/exFAT /dev/sda7 451223552 625141759 86959104 7 HPFS/NTFS/exFAT I found another problem just right now. I format last three drives as EXT4 with disk utility. But they are showing as NTFS/exFAT in fdisk. :-(

  Read the article

• Kingston SD reader not working for USB3

  - by user1146334

  I have a Kingston 4-in-1 Multimedia reader. When my PC was formatted with Win7 it worked fine. I decided to change to Ubuntu 14.04 and now it doesn't work. If I plug it into one of the USB2 ports it works fine, but whenever I plug it into one of the USB3 ports, it thinks about it for a minute and then dies. Here's the output of dmesg when it dies [110262.148656] usb 4-1: new SuperSpeed USB device number 3 using xhci_hcd [110262.170330] usb 4-1: Parent hub missing LPM exit latency info. Power management will be impacted. [110262.266379] usb 4-1: New USB device found, idVendor=11b0, idProduct=6348 [110262.266386] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [110262.266390] usb 4-1: Product: USB3.0 Media Reader [110262.266394] usb 4-1: Manufacturer: Kingston [110262.266398] usb 4-1: SerialNumber: 08735314400198 [110262.272929] usb-storage 4-1:1.0: USB Mass Storage device detected [110262.273239] scsi15 : usb-storage 4-1:1.0 [110263.290056] scsi 15:0:0:0: Direct-Access FCR-HS3 -0 1.00 PQ: 0 ANSI: 4 [110263.306622] scsi 15:0:0:1: Direct-Access FCR-HS3 -1 1.00 PQ: 0 ANSI: 4 [110263.323292] scsi 15:0:0:2: Direct-Access FCR-HS3 -2 1.00 PQ: 0 ANSI: 4 [110263.339858] scsi 15:0:0:3: Direct-Access FCR-HS3 -3 1.00 PQ: 0 ANSI: 4 [110263.340332] sd 15:0:0:0: Attached scsi generic sg3 type 0 [110263.340706] sd 15:0:0:1: Attached scsi generic sg4 type 0 [110263.340850] sd 15:0:0:2: Attached scsi generic sg5 type 0 [110263.340975] sd 15:0:0:3: Attached scsi generic sg6 type 0 [110264.651847] sd 15:0:0:1: [sde] 31116288 512-byte logical blocks: (15.9 GB/14.8 GiB) [110264.667049] sd 15:0:0:1: [sde] Write Protect is off [110264.667055] sd 15:0:0:1: [sde] Mode Sense: 2f 00 00 00 [110264.682767] sd 15:0:0:1: [sde] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [110264.694975] sd 15:0:0:2: [sdf] Attached SCSI removable disk [110264.697933] sd 15:0:0:3: [sdg] Attached SCSI removable disk [110264.729918] sd 15:0:0:0: [sdd] Attached SCSI removable disk [110264.754189] sde: sde1 [110264.760114] sd 15:0:0:1: [sde] Attached SCSI removable disk [110275.377368] usb 4-1: reset SuperSpeed USB device number 3 using xhci_hcd [110275.398453] usb 4-1: Parent hub missing LPM exit latency info. Power management will be impacted. [110275.436592] xhci_hcd 0000:05:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff8802e4fb9980 [110275.436600] xhci_hcd 0000:05:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff8802e4fb99c0 [110277.263444] usb 4-1: USB disconnect, device number 3

  Read the article

• 12.04 - How do I Fix Grub Error 15 on New Dual Boot Install

  - by Garth

  I just installed 12.04 to Dual Boot (separate partitions) with an existing Win 7. Upon reboot after install things freeze after Grub 1.5 with a Grub Error 15 message. Is there any easy way to fix this? (I am posting this from my second computer) UPDATE: I managed to boot into both 12.04 and Win7 using BIOS: Selected the disk with the Win7 'C' Partition: resulted in the same error message Rebooted, tried the disk with the Ubuntu Partitions: *Grub Menu loaded: Managed to boot 12.04, rebooted, used BIOS again: Managed to boot Win 7 So, I have access to my computer again (thru BIOS), but this has been a pretty crappy install experience. Garth I used the the Final release 12.04 Ubuntu install disk, reformatted all Linux partitions, and expected a simple clean install. Other than specifying the Ubuntu Partitions, I did a basic install of 12.04. No way I did do anything to get this crap error failure! I have no idea why my install resulted in a Grub-15 error. CLOSED - Answered my own Question: I burned a RescuTux Disk and used it to recover grub2 (simplest and easiest way for me. http://www.supergrubdisk.org/category/download/rescatuxdownloads/ Garth

  Read the article

• Cannot boot computer, help please :(

  - by Austin

  Ok so here is more descriptions, I REALLY NEED HELP! I installed Ubuntu on a disk (unsure of v. I can't check.. Computer is broke :/ ) I then burned the disk I restarted computer pressed f12 blah blah it came up, I pressed enter for English, I plugged an Ethernet card in for better connection, and then started the installation.... I did the basics, and I entered a host name, and a user name and pass all that, when it came to partition page, I presse enter for no and then it went back to the installation page, I pressed install again, and it brought me back, so I selected yes , it loaded an it asked what software to instal I selected sh ( it was first option and I didn't know which to do ) so after everything finished loading, my disk was ejected the process finish, I run my computer and it opens up in log in page on cmd script I didn't know it, so I ran disk again makin a user and pass to remember.... Going back to login thing I logged in, and all it did was say my username... I didn't know what to do from there, I looked online found nothing but grub stuff, so I went to "Advanced Ubuntu options" and then "(Recovery Mode) and went to update grub... In middle o loading it asked to continue (Y/n) I typed Y and it finished, it went back to the options located in (Recovery Mode) and I closed it, and it loaded... And then showed up in another script screen, saying a paragraph on top, and on left side ( where login: would be located etc. ) it says "Grub" and I don't know what to type, if I turn off computer and turn back on it just goes straight to that again... PLEASE HELP:(

  Read the article

• Stuck With grub rescue> console

  - by rej santos

  Here is the background of my issue: I just recently installed the latest version of Ubuntu along side with Windows 8 Enterprise. However upon checking the disk size, it seems that some of the portions of the hd memory were gone so I decided to check the disk partition and have seen that is was being used by another file system. Thinking that the Ubuntu takes it boots stuff from my drive C: , I deleted that partition and formated so I can use it to store some movies, music etc. Now, as I switch on my machine, I am stucked with: error: unknown filesystem grub rescue> I googled a lot and saw the following command which seems no to me like sudo, chainloader etc, all of these command only returns unknown command in the console. What I just wanted is to boot from my Windows 8 OS. Just to add, I can't open the BIOS menu so I could choose what media to boot. As I open my machine it automatically takes me to grub rescue console. Here are the thing I already have: Ubuntu Installation Disk Windows 8 System repair Disk I just don't know how to boot into these things. Let me know what to do.

  Read the article

• How can a usb be detected but not show up anywhere?

  - by George Mauer

  I started the morning by trying to create a bootable usb using a 2gb stick and the startup disk creator. It seemed to run through the whole process just fine until it got to a screen that read something like "Creating memory partion" and which sat on 100% for about 45 minutes before I hit cancel and removed the usb stick. Now the usb stick is not being detected as storage or...anything (even on my windows pc) though it does show up in the syslog. Allow me to demonstrate. We start with the usb not plugged in: [georgemauer@ubuntu:~]$ sudo fdisk -l (04-04 16:01) Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x994bdc0f Device Boot Start End Blocks Id System /dev/sda1 2048 27650047 13824000 27 Hidden NTFS WinRE /dev/sda2 * 27650048 27854847 102400 7 HPFS/NTFS/exFAT /dev/sda3 27854848 976771119 474458136 7 HPFS/NTFS/exFAT I plug in the usb: [georgemauer@ubuntu:~]$ tail -f /var/log/syslog ***Snip*** Apr 4 15:01:18 ubuntu wpa_supplicant[1136]: WPA: Group rekeying completed with 00:24:36:ad:e7:3f [GTK=TKIP] Apr 4 15:02:29 wpa_supplicant[1136]: last message repeated 3 times Apr 4 15:02:29 ubuntu kernel: [22122.788133] usb 2-1: new high speed USB device number 13 using ehci_hcd Apr 4 15:02:29 ubuntu kernel: [22122.923873] scsi10 : usb-storage 2-1:1.0 Apr 4 15:02:29 ubuntu mtp-probe: checking bus 2, device 13: "/sys/devices/pci0000:00/0000:00:13.2/usb2/2-1" Apr 4 15:02:30 ubuntu mtp-probe: bus: 2, device: 13 was not an MTP device Apr 4 15:02:30 ubuntu kernel: [22123.926154] scsi 10:0:0:0: Direct-Access GENERIC USB Mass Storage 1.00 PQ: 0 ANSI: 2 Apr 4 15:02:30 ubuntu kernel: [22124.105118] sd 10:0:0:0: Attached scsi generic sg1 type 0 Apr 4 15:02:30 ubuntu kernel: [22124.108212] sd 10:0:0:0: [sdb] Attached SCSI removable disk but then: [georgemauer@ubuntu:~]$ ls /mnt -alF (04-04 16:02) total 8 drwxr-xr-x 2 root root 4096 2011-04-21 12:51 ./ drwxr-xr-x 26 root root 4096 2012-03-31 13:16 ../ [georgemauer@ubuntu:~]$ ls /media -alF (04-04 16:03) total 8 drwxr-xr-x 2 root root 4096 2012-04-04 12:18 ./ drwxr-xr-x 26 root root 4096 2012-03-31 13:16 ../ What could be going on and how do I recover my usb key?

  Read the article

• Order in which passphrase is asked for encrypted volumes

  - by Lars Kotthoff

  I have installed 12.10 on a machine with two disks. The root partition is on one disk, the swap partition on the other. Both disks are encrypted and I have added the corresponding entries to /etc/crypttab. During boot, it asks for the passphrase for the disk with the root filesystem. Then it continues booting and gets to the login screen before I get a chance to enter the passphrase for the other disk. After logging in, I verified that it was actually waiting for me to enter the passphrase for that second partition (askpass process is running). But at that point, I have no way of entering the passphrase anymore. The manpage for crypttab suggests that the order in which the volumes are specified matters, so I changed it to have the swap disk first. I updated the initramfs and grub afterwards, but it didn't make any difference. How can I specify the order in which the encrypted partitions are unlocked? I'm looking for a solution that either asks for the swap passphrase first or tells the system to wait until all encrypted partitions are unlocked before displaying the login screen.

  Read the article

• Can't access external hard drives or thumb drives

  - by calden

  I am not a complete linux noob but I don't know a lot either and would greatly appreciate some help with this. I just installed Ubuntu 10.10 onto my laptop. Everything is working great however USB devices such as thumb drives and external hard drives wont show up. I have been looking around a bit and when I run sudo fdisk -l it displays this: Disk /dev/sda: 250.1 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00065684 Device Boot Start End Blocks Id System /dev/sda1 * 1 29255 234983424 83 Linux /dev/sda2 29255 30402 9212929 5 Extended /dev/sda5 29255 30402 9212928 82 Linux swap / Solaris Disk /dev/sdb: 16.0 GB, 16026435072 bytes 64 heads, 32 sectors/track, 15283 cylinders Units = cylinders of 2048 * 512 = 1048576 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000df90d Device Boot Start End Blocks Id System /dev/sdb1 * 1 15283 15649776 7 HPFS/NTFS It does seem to display my 16 gig thumb drive but other then seeing it here I cant access it to read and write files to it. It does the same with my external hard drive. I know those devices work as I have tried them on my other computer and they are working fine. Also this is what is in fstab if this will help anybody help me: proc /proc proc nodev,noexec,nosuid 0 0 /dev/sdb1 / ext4 errors=remount-ro 0 1 /dev/sdb5 none swap sw 0 0 Thank you very much for the help everyone.

  Read the article

< Previous Page | 226 227 228 229 230 231 232 233 234 235 236 237  | Next Page >