Search Results

Search found 6438 results on 258 pages for 'layer groups'.

Page 233/258 | < Previous Page | 229 230 231 232 233 234 235 236 237 238 239 240  | Next Page >

  • dhcp-snooping option 82 drops valid dhcp requests on 2610 series Procurve switches

    - by kce
    We are slowly starting to implement dhcp-snooping on our HP ProCurve 2610 series switches, all running the R.11.72 firmware. I'm seeing some strange behavior where dhcp-request or dhcp-renew packets are dropped when originating from "downstream" switches due "untrusted relay information from client". The full error: Received untrusted relay information from client <mac-address> on port <port-number> In more detail we have a 48 port HP2610 (Switch A) and a 24 port HP2610 (Switch B). Switch B is "downstream" of Switch A by virtue of a DSL connection to one of Switch A ports. The dhcp server is connected to Switch A. The relevant bits are as follows: Switch A dhcp-snooping dhcp-snooping authorized-server 192.168.0.254 dhcp-snooping vlan 1 168 interface 25 name "Server" dhcp-snooping trust exit Switch B dhcp-snooping dhcp-snooping authorized-server 192.168.0.254 dhcp-snooping vlan 1 interface Trk1 dhcp-snooping trust exit The switches are set to trust BOTH the port the authorized dhcp server is attached to and its IP address. This is all well and good for the clients attached to Switch A, but the clients attached to Switch B get denied due to the "untrusted relay information" error. This is odd for a few reasons 1) dhcp-relay is not configured on either switch, 2) the Layer-3 network here is flat, same subnet. DHCP packets should not have a modified option 82 attribute. dhcp-relay does appear to be enabled by default however: SWITCH A# show dhcp-relay DHCP Relay Agent : Enabled Option 82 : Disabled Response validation : Disabled Option 82 handle policy : append Remote ID : mac Client Requests Server Responses Valid Dropped Valid Dropped ---------- ---------- ---------- ---------- 0 0 0 0 SWITCH B# show dhcp-relay DHCP Relay Agent : Enabled Option 82 : Disabled Response validation : Disabled Option 82 handle policy : append Remote ID : mac Client Requests Server Responses Valid Dropped Valid Dropped ---------- ---------- ---------- ---------- 40156 0 0 0 And interestingly enough the dhcp-relay agent seems very busy on Switch B, but why? As far as I can tell there is no reason why dhcp requests need a relay with this topology. And furthermore I can't tell why the upstream switch is dropping legitimate dhcp requests for untrusted relay information when the relay agent in question (on Switch B) isn't modifying the option 82 attributes anyway. Adding the no dhcp-snooping option 82 on Switch A allows the dhcp traffic from Switch B to be approved by Switch A, by virtue of just turning off that feature. What are the repercussions of not validating option 82 modified dhcp traffic? If I disable option 82 on all my "upstream" switches - will they pass dhcp traffic from any downstream switch regardless of that traffic's legitimacy? This behavior is client operating system agnostic. I see it with both Windows and Linux clients. Our DHCP servers are either Windows Server 2003 or Windows Server 2008 R2 machines. I see this behavior regardless of the DHCP servers' operating system. Can anyone shed some light on what's happening here and give me some recommendations on how I should proceed with configuring the option 82 setting? I feel like i just haven't completely grokked dhcp-relaying and option 82 attributes.

    Read the article

  • Problem Disabling Roaming Profiles on Grouped Users

    - by user43207
    I'm having some serious issues getting a group of users to stop using roaming profiles. As expected, I have roaming profiles enabled accross the domain. - But am doing GPO filtering, limiting the scope. I originally had it set to authenticated users for Roaming, but as the domain has branched out to multiple locations, I've limited the scope to only people that are near the central office. The GPO that I have linked filtered to a group I have created that include users that I don't want to have roaming profiles. This GPO is sitting at the root of the domain, with the "Forced" setting enabled, so it should override any setting below it. *On a side note, it is the ONLY GPO that I have set to "Forced" right now. I know the GPO is working, since I can see the original registy settings on a user that logged in under roaming profiles - and then that same user logging in after I made the Group Policy changes, the registry reflects a local profile. But unfortunately, even after making those settings - the user is given a roaming profile on one of the servers. A gpresult of that same user account (after the updated gpo) is listed in the code block below. You can see right at the top of that output, that it is infact dealing with a roaming profile. - And sure enough, on the server that's hosting the file share for roaming profiles, it creates a folder for the user once they log in. For testing purposes, I've deleted all copies of the user's profile, roaming and local. But the problem is still here. - So I'm aparently missing something in the group policy settings on a wider scale. Would anybody be able to point me in the direction of what I'm missing here? *gpresult /r*** Microsoft (R) Windows (R) Operating System Group Policy Result tool v2.0 Copyright (C) Microsoft Corp. 1981-2001 Created On 5/15/2010 at 8:59:00 AM RSOP data for ** on * : Logging Mode OS Configuration: Member Workstation OS Version: 6.1.7600 Site Name: N/A Roaming Profile: \\profiles$** Local Profile: C:\Users*** Connected over a slow link?: No USER SETTINGS CN=*****,OU=*****,OU=*****,OU=*****,DC=*****,DC=***** Last time Group Policy was applied: 5/15/2010 at 8:52:02 AM Group Policy was applied from: *****.*****.com Group Policy slow link threshold: 500 kbps Domain Name: USSLINDSTROM Domain Type: Windows 2000 Applied Group Policy Objects ----------------------------- ForceLocalProfilesOnly InternetExplorer_***** GlobalPasswordPolicy The following GPOs were not applied because they were filtered out ------------------------------------------------------------------- DAgentFirewallExceptions Filtering: Denied (Security) WSAdmin_***** Filtering: Denied (Security) NetlogonFirewallExceptions Filtering: Not Applied (Empty) NetLogon_***** Filtering: Denied (Security) WSUSUpdateScheduleManualInstall Filtering: Denied (Security) WSUSUpdateScheduleDaily_0300 Filtering: Denied (Security) WSUSUpdateScheduleThu_0100 Filtering: Denied (Security) AlternateSSLFirewallExceptions Filtering: Denied (Security) SNMPFirewallExceptions Filtering: Denied (Security) WSUSUpdateScheduleSun_0100 Filtering: Denied (Security) SQLServerFirewallExceptions Filtering: Denied (Security) WSUSUpdateScheduleTue_0100 Filtering: Denied (Security) WSUSUpdateScheduleSat_0100 Filtering: Denied (Security) DisableUAC Filtering: Denied (Security) ICMPFirewallExceptions Filtering: Denied (Security) AdminShareFirewallExceptions Filtering: Denied (Security) GPRefreshInterval Filtering: Denied (Security) ServeRAIDFirewallExceptions Filtering: Denied (Security) WSUSUpdateScheduleFri_0100 Filtering: Denied (Security) BlockFirewallExceptions(8400-8410) Filtering: Denied (Security) WSUSUpdateScheduleWed_0100 Filtering: Denied (Security) Local Group Policy Filtering: Not Applied (Empty) WSUS_***** Filtering: Denied (Security) LogonAsService_Idaho Filtering: Denied (Security) ReportServerFirewallExceptions Filtering: Denied (Security) WSUSUpdateScheduleMon_0100 Filtering: Denied (Security) TFSFirewallExceptions Filtering: Denied (Security) Default Domain Policy Filtering: Not Applied (Empty) DenyServerSideRoamingProfiles Filtering: Denied (Security) ShareConnectionsRemainAlive Filtering: Denied (Security) The user is a part of the following security groups --------------------------------------------------- Domain Users Everyone BUILTIN\Users BUILTIN\Administrators NT AUTHORITY\INTERACTIVE CONSOLE LOGON NT AUTHORITY\Authenticated Users This Organization LOCAL *****Users VPNAccess_***** NetAdmin_***** SiteAdmin_***** WSAdmin_***** VPNAccess_***** LocalProfileOnly_***** NetworkAdmin_***** LocalProfileOnly_***** VPNAccess_***** NetAdmin_***** Domain Admins WSAdmin_***** WSAdmin_***** ***** ***** Schema Admins ***** Enterprise Admins Denied RODC Password Replication Group High Mandatory Level

    Read the article

  • Windows 7 Samba issue

    - by abduls85
    We have a strange samba issue affecting only one user. Our samba setup is as follow : Red Hat Enterprise Linux Server release 5.4 (Tikanga) - Samba Server Samba version 3.0.33-3.14.el5 - Samba version Domain Controller WIN2008R2 Standard - Windows DC Windows 7 64 bit - Client PCs User mentioned that he faced this problem after he force shutdown his PC few weeks ago. By right, for all users when we access \\sambaservername in windows it will show all the shares in the samba server but for this user once he startup his PC he will not be able to access \\sambaservername, Error message Windows cannot access \\sambaservername Current workaround to solve the problem : Try to access one share in \\sambaservername for instance \\sambaservername\sharedfolder1. But even when doing so, it will first prompt an error in the beginning, error message is as follows Logon failure: unknown user name or bad password. user need to enter the credentials again and he can access the share. Thereafter, he will be able to access \\sambaservername without any issues. But once he reboots his computer the problem will persists. Troubleshooting done so far: Ensure the following settings: Go to: Control Panel → Administrative Tools → Local Security Policy Select: Local Policies → Security Options "Network security: LAN Manager authentication level" → Send LM & NTLM responses "Minimum session security for NTLM SSP" → uncheck: Require 128-bit encryption Advise user to reset his password and try again but problem still persists Tried my account on users' PC, there is no issues. Tried user account on serveral other Windows 7 PC including mine but problem still persists. Windows XP does not have this problem. Ensure that there is no stored crendentials on the windows 7 PC. Checked the credentials manager in Control Panel as well as typing this command rundll32.exe keymgr.dll, KRShowKeyMgr Restart winbindd daemon on samba server but to no avail. I suspect this is due to some caching issue but not sure where is the issue. Whenever the user has error accessing \\sambaservername, the following errors will be logged in the samba server : [2012/10/10 17:10:26, 1] smbd/sesssetup.c:reply_spnego_kerberos(316) Failed to verify incoming ticket with error NT_STATUS_LOGON_FAILURE! [2012/10/10 17:10:27, 1] smbd/sesssetup.c:reply_spnego_kerberos(316) Failed to verify incoming ticket with error NT_STATUS_LOGON_FAILURE! [2012/10/10 17:10:27, 1] smbd/sesssetup.c:reply_spnego_kerberos(316) Failed to verify incoming ticket with error NT_STATUS_LOGON_FAILURE! [2012/10/10 17:10:27, 1] smbd/sesssetup.c:reply_spnego_kerberos(316) Failed to verify incoming ticket with error NT_STATUS_LOGON_FAILURE! [2012/10/10 17:10:27, 1] smbd/sesssetup.c:reply_spnego_kerberos(316) Failed to verify incoming ticket with error NT_STATUS_LOGON_FAILURE! [2012/10/10 17:10:27, 1] smbd/sesssetup.c:reply_spnego_kerberos(316) Failed to verify incoming ticket with error NT_STATUS_LOGON_FAILURE! [2012/10/10 17:10:27, 1] smbd/sesssetup.c:reply_spnego_kerberos(316) Failed to verify incoming ticket with error NT_STATUS_LOGON_FAILURE! [2012/10/10 17:10:27, 1] smbd/sesssetup.c:reply_spnego_kerberos(316) Failed to verify incoming ticket with error NT_STATUS_LOGON_FAILURE! [2012/10/10 17:10:27, 1] smbd/sesssetup.c:reply_spnego_kerberos(316) Failed to verify incoming ticket with error NT_STATUS_LOGON_FAILURE! [2012/10/10 17:10:27, 1] smbd/sesssetup.c:reply_spnego_kerberos(316) Failed to verify incoming ticket with error NT_STATUS_LOGON_FAILURE! But after workaround, there will be no more errors. I suspect after reading the article listed below some amendments need to be made to the \var\samba\cache directory : http://www.linuxquestions.org/questions/linux-server-73/getent-passwd-dont-show-ad-groups-and-users-745829/ http://www.samba.org/samba/docs/man/Samba-HOWTO-Collection/tdb.html http://lists.samba.org/archive/samba/2010-May/155521.html http://lists.samba.org/archive/samba/2011-March/161912.html http://lzeit.blogspot.sg/2009/10/samba-shares-inaccessible-after-power.html There are several users using the samba server and i would like to solve this problem without any impacts. I saw the following article : http://www.samba.org/samba/docs/man/manpages-3/smb.conf.5.html#WINBINDCACHETIME "winbind offline logon (G) This parameter is designed to control whether Winbind should allow to login with the pam_winbind module using Cached Credentials. If enabled, winbindd will store user credentials from successful logins encrypted in a local cache. Default: winbind offline logon = false Example: winbind offline logon = true " Any idea on how to delete the entry for one user in the local cache ?

    Read the article

  • Does likewise-open > version 5.4 contain CIFS support?

    - by Ben Andken
    I'm trying to get the CIFS server working in likewise-open. I've found this set of instructions and everything seems to work until I try to connect ([url]http://www.likewise.com/resources/documentation_library/manuals/cifs/likewise-cifs-smb-file-server-guide.html#id2765992):[/url] 1.6. Build and Configure a Standalone Likewise-CIFS Server This section demonstrates how to build and configure a standalone instance of Likewise-CIFS from the command line. The following procedure assumes that you want to set up Likewise-CIFS on a Linux server to share files with Windows computers in a network without Active Directory. This procedure also assumes you know how to build Linux applications from their source code and then install them. Download Likewise-CIFS from its open source git location: $ git clone git://git.likewiseopen.org/ Download, build, and install the following tools. The tools listed are known to work, but earlier or later versions might work as well. Also, instead of downloading the tools, you might be able to install them on your platform with apt-get or some other means. http://ftp.gnu.org/gnu/autoconf/autoconf-2.65.tar.gz http://ftp.gnu.org/gnu/automake/automake-1.9.6.tar.gz http://ftp.gnu.org/gnu/libtool/libtool-2.2.6a.tar.gz http://pkgconfig.freedesktop.org/releases/pkg-config-0.23.tar.gz gcc --version 3.x or greater Build Likewise-CIFS: $ cd likewise-open $ build/mkcomp --debug all Install Likewise-CIFS: $ sudo su $ cd staging/install-root $ tar cf - . | (cd / && tar xvf -) Make sure Samba is not running: $ /etc/init.d/smb stop Make sure SELinux is either disabled or set to permissive. Make sure the ports required by Likewise are open. For a list of ports that Likewise uses, see the Likewise Open Installation and Administration Guide. Configure Likewise Open: $ /etc/init.d/lwsmd start $ for i in /etc/likewise/*.reg; do /opt/likewise/bin/lwregshell upgrade $i; done $ /etc/init.d/lwsmd stop $ /etc/init.d/lwsmd start $ /opt/likewise/bin/lwsm start srvsvc $ /opt/likewise/bin/domainjoin-cli configure --enable nsswitch Add a user account to the local Likewise provider database. In the following example, substitute the account name that you want for newuser. $ /opt/likewise/bin/lw-add-user --home /home/newuser --shell /bin/bash newuser Successfully added user newuser Enable the user and set the password: $ /opt/likewise/bin/lw-mod-user --enable-user --set-password newuser New Password: ********** Successfully modified user newuser Look up new user's identity as follows. Substitute the value from the command hostname -s for the hostname. Keep in mind that Likewise truncates a hostname longer than 15 characters to the first 15 characters of the string. % id hostname\\newuser uid=2000(HOSTNAME\newuser) gid=1800(HOSTNAME\Likewise Users) groups=1800(HOSTNAME\Likewise Users) context=system_u:system_r:unconfined_t:s0 Make a CIFS directory for the user: mkdir /lwcifs/newuser chown 2000:1800 /lwcifs/newuser From a Windows computer, map the Likewise-CIFS drive share: Computer->Map Network Drive... Folder: \\IP_hostname\c$ Click "Finish" Username: hostname\newuser Password: user_password The last step fails when I try to connect. I've tried with Windows XP Pro and Windows 7 Pro. The rest of the directions only appear to work for version 5.4 (the one that shipped with 10.04). For 12.04, version 6.1 is the only one available and it doesn't appear to have the srvsvc module mentioned in these instructions. Is CIFS support dropped in the 6.1 version of likewise-open?

    Read the article

  • AdPrep logs show an LDAP error

    - by Omar
    What I am trying to do is transition our domain from Server 2003 Enterprise x32 to Server 2008 R2 Enterprise x64. Here is what I have done thus far. The 2003 server is a physical machine, the 2008 server is a virtual machine Built a virtual machine that has Server 2008 R2 Enterprise x64 and joined it to the domain as a domain member On the 2003 DC, Raised Domain Functional Level and Forest Functional Level to Windows Server 2003 On the 2003 DC, went into the registry and navigated to HKLM\SYSTEM\CurrentControlSet\Services\NTDS\Parameters and verified that the Schema Version is 30 On the 2003 DC, inserted the Windows Server 2008 Enterprise x32 Edition to copy over the adprep folder. This version is the only one that seemed to work On the 2003 DC, opened command prompt and went to adprep directory and ran adprep /forestprep , adprep /domainprep , and adprep /domainprep /gpprep On the 2008 server, Installed the Active Directory Domain Services role from Server Manager On the 2003 DC, went into the registry and navigated to HKLM\SYSTEM\CurrentControlSet\Services\NTDS\Parameters and verified that the Schema Version is now 44 When I go to run dcpromo on the 2008 server, I get a message that says: "To install a domain controller into this Active Directory forest, you must first prepare using adprep /forestprep" I went back to the 2003 DC server and went through the adprep logs and I came across this: Adprep was unable to modify the security descriptor on object CN=DomainControllerAuthentication,CN=Certificate Templates,CN=Public Key Services,CN=Services,CN=Configuration,DC=xeroxtoledo,DC=com. [Status/Consequence] ADPREP was unable to merge the existing security descriptor with the new access control entry (ACE). [User Action] Check the log file ADPrep.log in the C:\WINDOWS\debug\adprep\logs\20100327143517 directory for more information. Adprep encountered an LDAP error. *Error code: 0x20. Server extended error code: 0x208d, Server error message: 0000208D: NameErr: DSID-031001CD, problem 2001 (NO_OBJECT), data 0, best match of: 'CN=Certificate Templates,CN=Public Key Services,CN=Services,CN=Configuration,DC=xeroxtoledo,DC=com* In fact, I got three of these errors. The LDAP error is consistent with all three, but the top part where it says "Adprep was unable to modify the security descriptor on object" are different. They are the following: CN=DomainControllerAuthentication,CN=Certificate Templates,CN=Public Key Services,CN=Services,CN=Configuration,DC=xeroxtoledo,DC=com. CN=DirectoryEmailReplication,CN=Certificate Templates,CN=Public Key Services,CN=Services,CN=Configuration,DC=xeroxtoledo,DC=com. CN=KerberosAuthentication,CN=Certificate Templates,CN=Public Key Services,CN=Services,CN=Configuration,DC=xeroxtoledo,DC=com. The credentials I am using on the 2008 server when running dcpromo is my domain account. My account is part of the domain and enterprise admin groups. I've tried various quick fixes that I've came across through Google searches that include: Disabling AntiVirus on current DCs Pointing DNS on PDC to point to itself Changing the Schema Update Allowed key to 1 and tried rerunning adprep - when rerunning adprep, told me that Forest-wide information has already been updated Disabled Windows Firewall on the Server 2008 box On the 2003 DC, went to Domain Controller Security Policy Local Policies User Rights Assignment and added Domain Admins to the Enable computer and user accounts to be trusted for delegation policy setting Both our PDC and BDC are Global Catalog Servers. Not sure if this matters or not I ran the command netdom query fsmo and verified that the FSMO role holder is the current 2003 PDC I ran dcdiag /v on the 2003 PDC and the only thing that failed was Services. Dnscache Service is stopped on the PDC I even went as far as deleting the virtual machine and recreating it from scratch - no avail... Help :(

    Read the article

  • Useful Command-line Commands on Windows

    - by Sung Meister
    The aim for this Wiki is to promote using a command to open up commonly used applications without having to go through many mouse clicks - thus saving time on monitoring and troubleshooting Windows machines. Answer entries need to specify Application name Commands Screenshot (Optional) Shortcut to commands && - Command Chaining %SYSTEMROOT%\System32\rcimlby.exe -LaunchRA - Remote Assistance (Windows XP) appwiz.cpl - Programs and Features (Formerly Known as "Add or Remove Programs") appwiz.cpl @,2 - Turn Windows Features On and Off (Add/Remove Windows Components pane) arp - Displays and modifies the IP-to-Physical address translation tables used by address resolution protocol (ARP) at - Schedule tasks either locally or remotely without using Scheduled Tasks bootsect.exe - Updates the master boot code for hard disk partitions to switch between BOOTMGR and NTLDR cacls - Change Access Control List (ACL) permissions on a directory, its subcontents, or files calc - Calculator chkdsk - Check/Fix the disk surface for physical errors or bad sectors cipher - Displays or alters the encryption of directories [files] on NTFS partitions cleanmgr.exe - Disk Cleanup clip - Redirects output of command line tools to the Windows clipboard cls - clear the command line screen cmd /k - Run command with command extensions enabled color - Sets the default console foreground and background colors in console command.com - Default Operating System Shell compmgmt.msc - Computer Management control.exe /name Microsoft.NetworkAndSharingCenter - Network and Sharing Center control keyboard - Keyboard Properties control mouse(or main.cpl) - Mouse Properties control sysdm.cpl,@0,3 - Advanced Tab of the System Properties dialog control userpasswords2 - Opens the classic User Accounts dialog desk.cpl - opens the display properties devmgmt.msc - Device Manager diskmgmt.msc - Disk Management diskpart - Disk management from the command line dsa.msc - Opens active directory users and computers dsquery - Finds any objects in the directory according to criteria dxdiag - DirectX Diagnostic Tool eventvwr - Windows Event Log (Event Viewer) explorer . - Open explorer with the current folder selected. explorer /e, . - Open explorer, with folder tree, with current folder selected. F7 - View command history find - Searches for a text string in a file or files findstr - Find a string in a file firewall.cpl - Opens the Windows Firewall settings fsmgmt.msc - Shared Folders fsutil - Perform tasks related to FAT and NTFS file systems ftp - Transfers files to and from a computer running an FTP server service getmac - Shows the mac address(es) of your network adapter(s) gpedit.msc - Group Policy Editor gpresult - Displays the Resultant Set of Policy (RSoP) information for a target user and computer httpcfg.exe - HTTP Configuration Utility iisreset - To restart IIS InetMgr.exe - Internet Information Services (IIS) Manager 7 InetMgr6.exe - Internet Information Services (IIS) Manager 6 intl.cpl - Regional and Language Options ipconfig - Internet protocol configuration lusrmgr.msc - Local Users and Groups Administrator msconfig - System Configuration notepad - Notepad? ;) mmsys.cpl - Sound/Recording/Playback properties mode - Configure system devices more - Displays one screen of output at a time mrt - Microsoft Windows Malicious Software Removal Tool mstsc.exe - Remote Desktop Connection nbstat - displays protocol statistics and current TCP/IP connections using NBT ncpa.cpl - Network Connections netsh - Display or modify the network configuration of a computer that is currently running netstat - Network Statistics net statistics - Check computer up time net stop - Stops a running service. net use - Connects a computer to or disconnects a computer from a shared resource, or displays information about computer connections odbcad32.exe - ODBC Data Source Administrator pathping - A traceroute that collects detailed packet loss stats perfmon - Opens Reliability and Performance Monitor ping - Determine whether a remote computer is accessible over the network powercfg.cpl - Power management control panel applet quser - Display information about user sessions on a terminal server qwinsta - See disconnected remote desktop sessions reg.exe - Console Registry Tool for Windows regedit - Registry Editor rasdial - Connects to a VPN or a dialup network robocopy - Backup/Restore/Copy large amounts of files reliably rsop.msc - Resultant Set of Policy (shows the combined effect of all group policies active on the current system/login) runas - Run specific tools and programs with different permissions than the user's current logon provides sc - Manage anything you want to do with services. schtasks - Enables an administrator to create, delete, query, change, run and end scheduled tasks on a local or remote system. secpol.msc - Local Security Settings services.msc - Services control panel set - Displays, sets, or removes cmd.exe environment variables. set DIRCMD - Preset dir parameter in cmd.exe start - Starts a separate window to run a specified program or command start. - opens the current directory in the Windows Explorer. shutdown.exe - Shutdown or Reboot a local/remote machine subst.exe - Associates a path with a drive letter, including local drives systeminfo -Displays a comprehensive information about the system taskkill - terminate tasks by process id (PID) or image name tasklist.exe - List Processes on local or a remote machine taskmgr.exe - Task Manager telephon.cpl - Telephone and Modem properties timedate.cpl - Date and Time title - Change the title of the CMD window you have open tracert - Trace route wmic - Windows Management Instrumentation Command-line winver.exe - Find Windows Version wscui.cpl - Windows Security Center wuauclt.exe - Windows Update AutoUpdate Client

    Read the article

  • Custom initrd init script: how to create /dev/initctl

    - by Posco Grubb
    I have a virtual machine (VMM is Xen 3.3) equipped with two IDE HDD's (/dev/hda and /dev/hdb). The root file system is in /dev/hda1, where Scientific Linux 5.4 is installed. /dev/hdb contains an empty ext2 file system. I want to protect the root file system from writes by the VM by using aufs (AnotherUnionFS) to layer a writable file system on top of the root file system. The changes to / will be written to the file system located on /dev/hdb. (Furthermore, outside the VM, the file backing the /dev/hda will also be set to read-only permissions, so the VMM should also prevent the VM from modifying at that level.) (The purpose of this setup: be able to corrupt a virtual machine using software-implemented fault injection but preserve the file system image in order to quickly reboot the VM to a fault-free state.) How do I get an initrd init script to do the necessary mounts to create the union file system? I've tried 2 approaches: I've tried modifying the nash script that mkinitrd creates, but I don't know what setuproot and switchroot do and how to make them use my aufs as the new root. Apparently, nobody else here knows either. (EDIT: I take that back.) I've tried building a LiveCD (using linux-live-6.3.0) and then modifying the Bash /linuxrc script from the generated initrd, and I got the mounts correct, but the final /sbin/init complains about /dev/initctl. Specifically, my /linuxrc mounts the aufs at /union. The last few lines of /linuxrc effectively do the following: cd /union mkdir -p mnt/live pivot_root . mnt/live exec sbin/chroot . sbin/init </dev/console >/dev/console 2>&1 When init starts, it outputs something like init: /dev/initctl: No such file or directory. What is supposed to create this FIFO? I found no such filename in the original linuxrc and liblinuxlive scripts. I tried creating it via "mkfifo /dev/initctl", but then init complained about a timeout opening or writing to the FIFO. Would appreciate any help or pointers. Thanks.

    Read the article

  • How to export computers from Active Directory to XML using Powershell?

    - by CoDeRs
    I am trying to create a powershell scripts for Remote Desktop Connection Manager using the active directory module. My first thought was get a list of computers in AD and parse them out into XML format similar to the OU structure that is in AD. I have no problem with that, the below code will work just but not how I wanted. EG # here is a the array $OUs Americas/Canada/Canada Computers/Desktops Americas/Canada/Canada Computers/Laptops Americas/Canada/Canada Computers/Virtual Computers Americas/USA/USA Computers/Laptops Computers Disabled Accounts Domain Controllers EMEA/UK/UK Computers/Desktops EMEA/UK/UK Computers/Laptops Outside Sales and Service/Laptops Servers I wanted to have the basic XML structured like this Americas Canada Canada Computers Desktops Laptops Virtual Computers USA USA Computers Laptops Computers Disabled Accounts Domain Controllers EMEA UK UK Computers Desktops Laptops Outside Sales and Service Laptops Servers However if you run the below it does not nest the next string in the array it only restarts the from the beginning and duplicating Americas Canada Canada Computers Desktops Americas Canada Canada Computers Laptops Americas Canada Canada Computers Virtual Computers Americas USA USA Computers Laptops RDCMGenerator.ps1 #Importing Microsoft`s PowerShell-module for administering ActiveDirectory Import-Module ActiveDirectory #Initial variables $OUs = @() $RDCMVer = "2.2" $userName = "domain\username" $password = "Hashed Password+" $Path = "$env:temp\test.xml" $allComputers = Get-ADComputer -LDAPFilter "(OperatingSystem=*)" -Properties Name,Description,CanonicalName | Sort-Object CanonicalName | select Name,Description,CanonicalName $allOUObjects = $allComputers | Foreach {"$($_.CanonicalName)"} Function Initialize-XML{ ##<RDCMan schemaVersion="1"> $xmlWriter.WriteStartElement('RDCMan') $XmlWriter.WriteAttributeString('schemaVersion', '1') $xmlWriter.WriteElementString('version',$RDCMVer) $xmlWriter.WriteStartElement('file') $xmlWriter.WriteStartElement('properties') $xmlWriter.WriteElementString('name',$env:userdomain) $xmlWriter.WriteElementString('expanded','true') $xmlWriter.WriteElementString('comment','') $xmlWriter.WriteStartElement('logonCredentials') $XmlWriter.WriteAttributeString('inherit', 'None') $xmlWriter.WriteElementString('userName',$userName) $xmlWriter.WriteElementString('domain',$env:userdomain) $xmlWriter.WriteStartElement('password') $XmlWriter.WriteAttributeString('storeAsClearText', 'false') $XmlWriter.WriteRaw($password) $xmlWriter.WriteEndElement() $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('connectionSettings') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('gatewaySettings') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('remoteDesktop') $XmlWriter.WriteAttributeString('inherit', 'None') $xmlWriter.WriteElementString('size','1024 x 768') $xmlWriter.WriteElementString('sameSizeAsClientArea','True') $xmlWriter.WriteElementString('fullScreen','False') $xmlWriter.WriteElementString('colorDepth','32') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('localResources') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('securitySettings') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('displaySettings') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteEndElement() } Function Create-Group ($groupName){ #Start Group $xmlWriter.WriteStartElement('properties') $xmlWriter.WriteElementString('name',$groupName) $xmlWriter.WriteElementString('expanded','true') $xmlWriter.WriteElementString('comment','') $xmlWriter.WriteStartElement('logonCredentials') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('connectionSettings') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('gatewaySettings') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('remoteDesktop') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('localResources') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('securitySettings') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('displaySettings') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteEndElement() } Function Create-Server ($computerName, $computerDescription) { #Start Server $xmlWriter.WriteStartElement('server') $xmlWriter.WriteElementString('name',$computerName) $xmlWriter.WriteElementString('displayName',$computerDescription) $xmlWriter.WriteElementString('comment','') $xmlWriter.WriteStartElement('logonCredentials') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('connectionSettings') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('gatewaySettings') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('remoteDesktop') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('localResources') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('securitySettings') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteStartElement('displaySettings') $XmlWriter.WriteAttributeString('inherit', 'FromParent') $xmlWriter.WriteEndElement() $xmlWriter.WriteEndElement() #Stop Server } Function Close-XML { $xmlWriter.WriteEndElement() $xmlWriter.WriteEndElement() # finalize the document: $xmlWriter.Flush() $xmlWriter.Close() notepad $path } #Strip out Domain and Computer Name from CanonicalName foreach($OU in $allOUObjects){ $newSplit = $OU.split("/") $rebildOU = "" for($i=1; $i -le ($newSplit.count - 2); $i++){ $rebildOU += $newSplit[$i] + "/" } $OUs += $rebildOU.substring(0,($rebildOU.length - 1)) } #Remove Duplicate OU's $OUs = $OUs | select -uniq #$OUs # get an XMLTextWriter to create the XML $XmlWriter = New-Object System.XMl.XmlTextWriter($Path,$UTF8) # choose a pretty formatting: $xmlWriter.Formatting = 'Indented' $xmlWriter.Indentation = 1 $XmlWriter.IndentChar = "`t" # write the header $xmlWriter.WriteStartDocument() # # 'encoding', 'utf-8' How? # # set XSL statements #Initialize Pre-Defined XML Initialize-XML ######################################################### # Start Loop for each OU-Path that has a computer in it ######################################################### foreach ($OU in $OUs){ $totalGroupName = "" #Create / Reset Total OU-Path Completed $OU.split("/") | foreach { #Split the OU-Path into individual OU's $groupName = "$_" #Current OU $totalGroupName += $groupName + "/" #Total OU-Path Completed $xmlWriter.WriteStartElement('group') #Start new XML Group Create-Group $groupName #Call function to create XML Group ################################################ # Start Loop for each Computer in $allComputers ################################################ foreach($computer in $allComputers){ $computerOU = $computer.CanonicalName #Set the computers OU-Path $OUSplit = $computerOU.split("/") #Create the Split for the OU-Path $rebiltOU = "" #Create / Reset the stripped OU-Path for($i=1; $i -le ($OUSplit.count - 2); $i++){ #Start Loop for OU-Path to strip out the Domain and Computer Name $rebiltOU += $OUSplit[$i] + "/" #Rebuild the stripped OU-Path } if ($rebiltOU -eq $totalGroupName){ #Compare the Current OU-Path with the computers stripped OU-Path $computerName = $computer.Name #Set the computer name $computerDescription = $computerName + " - " + $computer.Description #Set the computer Description Create-Server $computerName $computerDescription #Call function to create XML Server } } } ################################################### # Start Loop to close out XML Groups created above ################################################### $totalGroupName.split("/") | foreach { #Split the if ($_ -ne "" ){ $xmlWriter.WriteEndElement() #End Group } } } Close-XML

    Read the article

  • The Koyal Group Info Mag News¦Charged building material could make the renewable grid a reality

    - by Chyler Tilton
    What if your cell phone didn’t come with a battery? Imagine, instead, if the material from which your phone was built was a battery. The promise of strong load-bearing materials that can also work as batteries represents something of a holy grail for engineers. And in a letter published online in Nano Letters last week, a team of researchers from Vanderbilt University describes what it says is a breakthrough in turning that dream into an electrocharged reality. The researchers etched nanopores into silicon layers, which were infused with a polyethylene oxide-ionic liquid composite and coated with an atomically thin layer of carbon. In doing so, they created small but strong supercapacitor battery systems, which stored electricity in a solid electrolyte, instead of using corrosive chemical liquids found in traditional batteries. These supercapacitors could store and release about 98 percent of the energy that was used to charge them, and they held onto their charges even as they were squashed and stretched at pressures up to 44 pounds per square inch. Small pieces of them were even strong enough to hang a laptop from—a big, fat Dell, no less. Although the supercapacitors resemble small charcoal wafers, they could theoretically be molded into just about any shape, including a cell phone’s casing or the chassis of a sedan. They could also be charged—and evacuated of their charge—in less time than is the case for traditional batteries. “We’ve demonstrated, for the first time, the simple proof-of-concept that this can be done,” says Cary Pint, an assistant professor in the university’s mechanical engineering department and one of the authors of the new paper. “Now we can extend this to all kinds of different materials systems to make practical composites with materials specifically tailored to a host of different types of applications. We see this as being just the tip of a very massive iceberg.” Pint says potential applications for such materials would go well beyond “neat tech gadgets,” eventually becoming a “transformational technology” in everything from rocket ships to sedans to home building materials. “These types of systems could range in size from electric powered aircraft all the way down to little tiny flying robots, where adding an extra on-board battery inhibits the potential capability of the system,” Pint says. And they could help the world shift to the intermittencies of renewable energy power grids, where powerful batteries are needed to help keep the lights on when the sun is down or when the wind is not blowing. “Using the materials that make up a home as the native platform for energy storage to complement intermittent resources could also open the door to improve the prospects for solar energy on the U.S. grid,” Pint says. “I personally believe that these types of multifunctional materials are critical to a sustainable electric grid system that integrates solar energy as a key power source.”

    Read the article

  • Tying down a cloud by virtualizing everything and then locking VMs to real hardware as necessary

    - by tudor
    I'm looking for a cloud software solution that: Can run on both server and desktop machines; Virtualizes hardware and has the option of exposing each real machine to the cloud; Allows a VM to be "locked" to a set of real hardware capabilities and stay there until moved (e.g. a user's "real" desktop); Allows a VM to link to some types of devices elsewhere (e.g. USB/serial via ethernet); and Is geography-aware to control movement of VMs between real networks. I'm aware that this may be the holy grail of virtualization, and I've searched alot. Some solutions appear to meet some criteria but not others. Most cloud implementations appear to ignore real hardware, for example. I realise that this may be solved by using three different implementations in combination: A standard cloud server farm. A bare-metal network backup utility with PXEBoot. VNC and/or VDI. (VNC obviously would require the real hardware to be running.) This combination, however, has some serious drawbacks that I'd like to solve by treating it as one system. My explanation follows... I have a network of real servers and desktops in multiple locations. I've virtualized servers before using Virtualbox and that's worked quite well. I've even connected USB devices to VMs on servers. I would like to virtualize the desktops in all my offices to facilitate movement of desktops, remote access (e.g. VDI) and bare-metal backups. However, I know that there are problems with this. For example, some desktops have specific hardware (e.g. 3D graphics cards, USB devices, etc) that limit their mobility. Geographic constraints also limit movement in that VMs can be moved easily within offices, but transferring between offices is not always preferable. What I would like to find is a system that can virtualize everything from bare-metal easily by maintaining an abstraction layer on each client and server machine that exposes the hardware available and runs as a cloud. Then certain VMs would be "locked" to specific hardware (so that, e.g. the VM runs only on their own desktop.) This would be required for situations where speed is important (e.g. 3D graphics pass-through). In addition, abstracted low-speed devices (e.g. USB) could be piped from real hardware to a VM in the cloud. This is important since if a VM is taken down, another VM can connect to the real hardware for minimum downtime.

    Read the article

  • Install Intel USB 3.0 eXtensible Host Controller Driver for Windows Server 2008 R2 x64

    - by ffrugone
    According to Intel and Dell, by board is technically a 'desktop' board and they therefore do not support Intel USB 3.0 eXtensible Host Controller drivers for Windows Server 2008 (R2 x64). I'm trying to find a workaround. I found an entry on someone who tried to tackle this, but I can't make his fix work for me. Below, I have copied both his entry, and my reply. I'm a loyal stackoverflow user, and hopefully the people here at serverfault can help me: anyforumuser Re: GA-Z77X-UD5H USB3 Drivers not installing? « Reply #6 on: July 05, 2012, 04:12:59 am » Thanks to JoeMiner , his process for the network drivers gave me the clues to figure out to get the USB3 drivers working. I have got the intel USB3 drivers working at full speed in win server 2008r2 you have to edit the following file : 1. mup.xml in change the "Windows7" to "W2K8" 2. in setup.if2 under [groups] line starting with "HSCSDRIVER " change the "IsOS( ... )" entry to "IsOS(WIN2008_R2,WIN2008_R2_MAXSP)" inf files for all copy the content of the [Intel.NTAMD64.6.1] group to the [Intel.NTAMD64.6.2] group driver folders. here i am not entirely sure which is correct so there are some double up's. in the drivers folder copy the "Win7" folder to "win2008" , "win2008_r2" and "x64" ie your drivers folder should now contain the "win2008" , "win2008_r2" and "x64" folders and they contain contents of the win7 folder (the inf files should of already been fixed) Run install , It should install properly and work now. You will have to reboot If it doesn't work remove the intel usb3 controllers from device manager and get it to "scan for hardware changes" Good luck !!! benevida Re: GA-Z77X-UD5H Intel Network Drivers not installing? « Reply #7 on: August 13, 2012, 02:21:14 pm » Thank you anyforumuser! A process for getting this driver installed was exactly what I needed. However, I've hit a snag. I believe I've followed every step exactly as written, but I'm getting an error during installation. I get the message "One or more files that are required for installation are either missing or corrupted. Setup will exit." Behind the error, the 'Setup Progress' shows the current step as "Copying File: C:\Program Files (x86)\Intel\Intel(R) USB 3.0 eXtensible Host Controller Driver\Drivers\iusb3xhc.man". I've checked the installation files, and iusb3xhc.man seems to be a viable file in all of the Windows 2008 sub-directories of the Drivers folder. Therefore I don't see how the file could be missing and I doubt that it is corrupted, (although it does NOT exist in the \Drivers\HCSwitch folder). I opened 'Setup.if2', and there are two aspects to the step of copying iusb3xhc.man that caught my eye. First, the steps immediately preceding are set to 'error=ignore'. If they hadn't completed successfully, this is the first step where we'd hear about it. Second, this is the first step where the relative path '%source%\drivers\%_os%\%_ia%\' is used. If I haven't named the Windows 2008 sub-directories correctly, I could see where things are fouling up. In any event, if someone could take a look and make suggestions I'd appreciate it. Thank you.

    Read the article

  • How to recover data files from xampp-windows to xampp-linux after crash?

    - by David Buehler
    My Windows box died after I developed a database in xampp on it; fortunately I have a backup of the entire F:/TestWeb/Xampp partition. Unfortunately, I did not do an Export (nor dump) of the "Lws2" database before the crash. I have replaced the defunct machine with one running Mint7 (based on Ubuntu 9.04 "Jaunty Jackalope") and installed xampp-linux into the /opt partition, so the new xampp now runs fine in /opt/lampp, and says all the elements are secured by passwords (which I just assigned during this installation.) I assumed that Xamp-Windows installed in November would migrate easily to xampp-linux installed iin February -- a bad assumption. It apparently would have been simple if I had known enough to do an Export or a Dump before the crash, but.... The backup was done to a Network Attached Storage drive, which is formatted as "vfat" so the backup does not carry with it any valid ownership permissions from MySql on NTFS. I now see from my backup that the old data resided in \TestWeb\Xampp\Mysql\Data\Lws2\ and consists of 7 ".frm" files which define my tables. The actual data -- I suppose a ".sql" file or files -- has disappeared, and I am resigning myself to two days of retyping it. But I do not wish to do the table layouts all over again. So I copied Data tree to /opt/lampp/Data -- PhpMyAdmin does not see it. So I copied Lws2 tree to /opt/lampp/Lws2 -- PhpMyAdmin does not see it. So I copied Data tree to /opt/lampp/var/mysql/Data -- PhpMyAdmin does not see it. So I copied Lws2 tree to /opt/lampp/var/mysql/Lws2 -- PhpMyAdmin does not see it. So I adjusted all the permissions to stop saying owner "nobody" to owner "root" and gave full permissions to all groups and to all others, with permissions percolating down, in all 4 trees. You guessed it -- PhpMyAdmin does not see any database named Lws2, only its 4 default ones. I double-checked the permissions and rebooted Linux and repeated the tests. At some point in that process I did see PhpMyAdmin showing "lws2(7)" but when I clicked on it I saw a "no table found" message. I have not been able to recreate that experience. Apparently there are some setup files for MySql and for PhpMyAdmin which need to be set up by running a wizard or two or by editing the files directly. I grepped the TestWeb tree and found an old "ldir = "C:TestWeb\Xampp\MySql\" and a "DataDir = C:TestWeb\Xampp\MySql\" in a .php file and in a .bat file, but I cannot find the corresponding config file names on the /opt partition/ -- so it looks as if these wizards have not been run to create them. What config files files does Linux use to setup MySql config files for PhpMyAdmin? What wizards do I need to run to point the MySql engine and the PhpMyAdmin at the folder /opt/lampp/data/ with its lws2 folder inside it? Or which files do I need to edit, with a sample of what it normally says under Linux? Incidentally, I remember I converted from MyISAM with its .MYD and .MYI files to InnoDB after entering only a small amount of the data -- and I do not know what file types to look for -- perhaps my data is still there but under another guise or in another place? Is it something as simple as linux needing to see "/data/" instead of /Data? I will check that out while waiting for a response. If anyone can point me to documentation that discusses this level of detail -- I will read it avidly! In any case, thanks for any clarification you can give on this thorny problem. wizdum

    Read the article

  • Failed Administrator login on WSO2 IS with external OpenLDAP

    - by Marco Rivadeneyra
    I have an installation of WSO2 Identity Server and I'm trying to make it work with an external OpenLDAP instance I have followed this guide: http://wso2.org/project/solutions/identity/3.2.3/docs/user-core/admin_guide.html#LDAP For the read-only mode. But when I try to log-in I get a failed login and the following error on the console: TID: [0] [WSO2 Identity Server] [2012-08-10 17:10:25,493] WARN {org.wso2.carbon.core.services.util.CarbonAuthenticationUtil} - Failed Administrator login attempt 'john[0]' at [2012-08-10 17:10:25,0493] from IP address 127.0.0.1 {org.wso2.carbon.core.services.util.CarbonAuthenticationUtil} Full log: http://pastebin.com/pHUGXBqv My configuration file looks as follows: <UserManager> <Realm> <Configuration> <AdminRole>admin</AdminRole> <AdminUser> <UserName>john</UserName> <Password>johnldap</Password> </AdminUser> <EveryOneRoleName>everyone</EveryOneRoleName> <!-- By default users in this role sees the registry root --> <ReadOnly>true</ReadOnly> <MaxUserNameListLength>500</MaxUserNameListLength> <Property name="url">jdbc:h2:repository/database/WSO2CARBON_DB</Property> <Property name="userName">wso2carbon</Property> <Property name="password">wso2carbon</Property> <Property name="driverName">org.h2.Driver</Property> <Property name="maxActive">50</Property> <Property name="maxWait">60000</Property> <Property name="minIdle">5</Property> </Configuration> <UserStoreManager class="org.wso2.carbon.user.core.ldap.LDAPUserStoreManager"> <Property name="ReadOnly">true</Property> <Property name="MaxUserNameListLength">100</Property> <Property name="ConnectionURL">ldap://192.168.81.144:389</Property> <Property name="ConnectionName">cn=admin,dc=example,dc=com</Property> <Property name="ConnectionPassword">admin</Property> <Property name="UserSearchBase">ou=People,dc=example,dc=com</Property> <Property name="UserNameListFilter">(objectClass=inetOrgPerson)</Property> <Property name="UserNameAttribute">uid</Property> <Property name="ReadLDAPGroups">false</Property> <Property name="GroupSearchBase">ou=Groups,dc=example,dc=com</Property> <Property name="GroupSearchFilter">(objectClass=groupOfNames)</Property> <Property name="GroupNameAttribute">uid</Property> <Property name="MembershipAttribute">member</Property> </UserStoreManager> <AuthorizationManager class="org.wso2.carbon.user.core.authorization.JDBCAuthorizationManager"></AuthorizationManager> </Realm> I followed this guide to configure my LDAP server up to Loggging: https://help.ubuntu.com/12.04/serverguide/openldap-server.html Could you suggest what might be wrong? The LDAP log is available at: http://pastebin.com/T9rFYEAW

    Read the article

  • Samba with remote LDAP authentication doesn`t see users properly

    - by LucasBr
    I'm trying to setup a samba server authenticated by a remote LDAP server, and I'm having some problems that I can't figure how to solve. I was able to make an getent passwd at samba server and I could see all users at ldapserver, but when I tried to access \\SAMBASERVER at my windows box I had this at the /var/log/samba/log.mywindowsbox: <...snip...> [2012/10/19 13:05:22.449684, 2] smbd/sesssetup.c:1413(setup_new_vc_session) setup_new_vc_session: New VC == 0, if NT4.x compatible we would close all old resources. [2012/10/19 13:05:22.449692, 3] smbd/sesssetup.c:1212(reply_sesssetup_and_X_spnego) Doing spnego session setup [2012/10/19 13:05:22.449701, 3] smbd/sesssetup.c:1254(reply_sesssetup_and_X_spnego) NativeOS=[] NativeLanMan=[] PrimaryDomain=[] [2012/10/19 13:05:22.449717, 3] libsmb/ntlmssp.c:747(ntlmssp_server_auth) Got user=[lucas] domain=[BUSINESS] workstation=[MYWINDOWSBOX] len1=24 len2=24 [2012/10/19 13:05:22.449747, 3] auth/auth.c:216(check_ntlm_password) check_ntlm_password: Checking password for unmapped user [BUSINESS]\[lucas]@[MYWINDOWSBOX] with the new password interface [2012/10/19 13:05:22.449759, 3] auth/auth.c:219(check_ntlm_password) check_ntlm_password: mapped user is: [SAMBASERVER]\[lucas]@[MYWINDOWSBOX] [2012/10/19 13:05:22.449773, 3] smbd/sec_ctx.c:210(push_sec_ctx) push_sec_ctx(0, 0) : sec_ctx_stack_ndx = 1 [2012/10/19 13:05:22.449783, 3] smbd/uid.c:429(push_conn_ctx) push_conn_ctx(0) : conn_ctx_stack_ndx = 0 [2012/10/19 13:05:22.449791, 3] smbd/sec_ctx.c:310(set_sec_ctx) setting sec ctx (0, 0) - sec_ctx_stack_ndx = 1 [2012/10/19 13:05:22.449922, 2] lib/smbldap.c:950(smbldap_open_connection) smbldap_open_connection: connection opened [2012/10/19 13:05:23.001517, 3] lib/smbldap.c:1166(smbldap_connect_system) ldap_connect_system: successful connection to the LDAP server [2012/10/19 13:05:23.007713, 3] smbd/sec_ctx.c:418(pop_sec_ctx) pop_sec_ctx (0, 0) - sec_ctx_stack_ndx = 0 [2012/10/19 13:05:23.007733, 3] auth/auth_sam.c:399(check_sam_security) check_sam_security: Couldn't find user 'lucas' in passdb. [2012/10/19 13:05:23.007743, 2] auth/auth.c:314(check_ntlm_password) check_ntlm_password: Authentication for user [lucas] -> [lucas] FAILED with error NT_STATUS_NO_SUCH_USER [2012/10/19 13:05:23.007760, 3] smbd/error.c:80(error_packet_set) error packet at smbd/sesssetup.c(111) cmd=115 (SMBsesssetupX) NT_STATUS_LOGON_FAILURE [2012/10/19 13:05:23.010469, 3] smbd/process.c:1489(process_smb) Transaction 3 of length 142 (0 toread) <...snip...> /etc/samba/smb.conf file follows: [global] dos charset = 850 unix charset = LOCALE workgroup = BUSINESS netbios name = SAMBASERVER bind interfaces only = true interfaces = lo eth0 eth1 smb ports = 139 hosts deny = All hosts allow = 192.168.78. 192.168.255. 127.0.0.1 10.149.122. 192.168.0. name resolve order = wins bcast hosts log level = 3 syslog = 0 log file = /var/log/samba/log.%m max log size = 100000 domain logons = No wins support = Yes wins proxy = No client ntlmv2 auth = Yes lanman auth = Yes ntlm auth = Yes dns proxy = Yes time server = Yes security = user encrypt passwords = Yes obey pam restrictions = Yes ldap password sync = Yes unix password sync = Yes passdb backend = ldapsam:"ldap://192.168.78.206" ldap ssl = off ldap admin dn = uid=root,ou=Users,dc=business,dc=intranet ldap suffix = ldap group suffix = ou=Groups ldap user suffix = ou=Users ldap machine suffix = ou=Computers ldap idmap suffix = ou=Idmap ldap delete dn = Yes add user script = /usr/sbin/smbldap-useradd -m "%u" delete user script = /usr/sbin/smbldap-userdel "%u" add group script = /usr/sbin/smbldap-groupadd -p "%g" delete group script = /usr/sbin/smbldap-groupdel "%g" add user to group script = /usr/sbin/smbldap-groupmod -m "%u" "%g" delete user from group script = /usr/sbin/smbldap-groupmod -x "%u" "%g" set primary group script = /usr/sbin/smbldap-usermod -g "%g" "%u" add machine script = /usr/sbin/smbldap-useradd -W -t5 "%u" idmap backend = ldap:"ldap://192.168.78.206" idmap uid = 16777216-33554431 idmap gid = 16777216-33554431 load printers = No printcap name = /dev/null map acl inherit = Yes map untrusted to domain = Yes enable privileges = Yes veto files = /lost+found/ /publicftp/ So, \\SAMBASERVER says he couldn't find my user, but I can see it by getent passwd . What I can do in order to SAMBASERVER see and authenticate my user? Thanks in advance!

    Read the article

  • Planning trunk capacity for multiple GbE switches

    - by wuckachucka
    Without measuring throughput (it's at the top of the list; this is just theoretical), I want to know the most standard method for trunking VLANs on multiple Gigabit (GbE) switches to a core Layer 3 GbE switch. Say you have three VLANs: VLAN10 (10.0.0.0/24) Servers: your typical Windows DC/file server, Exchange, and an Accounting/SQL server. VLAN20: (10.0.1.0/24) Sales: needs access to everything on VLAN10; doesn't need access to VLAN30 and vice-versa. VLAN20: (10.0.1.0/24) Support: needs access to everything on VLAN10; doesn't need access to VLAN20 and vice-versa. Here's how I think this should work in my head: Switch #1: Ports 2-20 are assigned to VLAN20; all the Sales workstations and printers are connected here. Optional 10GbE combo port #1 is trunked to L3 switch's 10 GbE combo port #1. Switch #2: Ports 2-20 are assigned to VLAN30; all the Support workstations and printers are connected here. Optional 10GbE combo port #1 is trunked to L3 switch's 10 GbE combo port #2. Core L3 switch: Ports 2-10 are assigned to VLAN10; all three servers are connected here. With a standard 10/100 x 24 switch, it'll usually come with one or two 1 GbE uplink ports; carrying over this logic to a 10/100/1000 x 24, the "optional" 10 GbE combo ports that most higher-end switches can get shouldn't really be an option. Keep in mind I haven't tested anything yet, I'm primarily moving in this direction for growth (don't want to buy 10/100 switches and have to replace those within a couple of years) and security (being able to control access between VLANs with L3 routing/packet filtering ACLs). Does this sound right? Do I really need the 10 GbE ports? It seems very non-standard and expensive, but it "feels" right when you think about 40 or 50 workstations trunking up to the L3 switch over 1 GbE standard ports. If say 20 workstations want to download a 10 GB image from the servers concurrently, wouldn't the trunk be the bottleneck? At least if the trunk was 10 GbE, you'd have 10x1GbE nodes being able to reach their theoretical max. What about switch stacking? Some of the D-Links I've been looking at have HDMI interfaces for stacking. As far as I know, stacking two switches creates one logical switch, but is this just for management I/O or does the switches use the (assuming it's HDMI 1.3) 10.2 Gbps for carrying data back and forth?

    Read the article

  • IMAPSync Migration to Exchange 2010 SP1: Exchange drops connections while checking for existence of folders

    - by Benjamin Priestman
    I'm migrating from ZImbra Collaboration Suite to Exchange 2010 SP1. I'm testing IMAPSync as a possible migration tool and have hit a problem with the IMAP server in Exchange 2010. For each account it migrates, IMAPSync loops through the list of folders in the source mailbox and tests for the existence of each one in the destination mailbox. It then goes on to create those folders that do not exist and copy over the messages. It's the intial testing for the existence of the folders that is giving me a problem. The response given by the Exchange server when the folder does not yet exist is given as an error: "R=""16 NO IMAPSyncTest/8 doesn't exist."" After ten of these errors have been issued in succession, the Exchange server appears to stop responding to the IMAP session. Enabling protocol logging for IMAP confirms that the 10th request for a non-existant folder is the last request to be logged on the server. IMAPSync carries on merrily without seeming to realise its connection has gone and thus fails to create any folders. I've logged this with the tool's creator. Does anyone have any idea why Exchange is stopping responding to the connections though? The behaviour looks rather like throttling, although the 'ten strikes and you're out' trigger does not seem to correspond to any of the triggers on the ThrottlingPolicies. Just to check, I've tried creating a new ThrottlingPolicy, turned everything that I think might be relevant up to 11 and applied it to the my test mailbox. Policy settings are listed below, along with IMAP settings. Everything else should be pretty much as default. Throttling Policy RunspaceId : afa3159c-32a6-4906-986f-8adfbe50868b IsDefault : False AnonymousMaxConcurrency : 1 AnonymousPercentTimeInAD : AnonymousPercentTimeInCAS : AnonymousPercentTimeInMailboxRPC : EASMaxConcurrency : 10 EASPercentTimeInAD : EASPercentTimeInCAS : EASPercentTimeInMailboxRPC : EASMaxDevices : 10 EASMaxDeviceDeletesPerMonth : EWSMaxConcurrency : 10 EWSPercentTimeInAD : 50 EWSPercentTimeInCAS : 90 EWSPercentTimeInMailboxRPC : 60 EWSMaxSubscriptions : 5000 EWSFastSearchTimeoutInSeconds : 60 EWSFindCountLimit : 1000 IMAPMaxConcurrency : 1000 IMAPPercentTimeInAD : 400 IMAPPercentTimeInCAS : 400 IMAPPercentTimeInMailboxRPC : 400 OWAMaxConcurrency : 5 OWAPercentTimeInAD : 30 OWAPercentTimeInCAS : 150 OWAPercentTimeInMailboxRPC : 150 POPMaxConcurrency : 20 POPPercentTimeInAD : POPPercentTimeInCAS : POPPercentTimeInMailboxRPC : PowerShellMaxConcurrency : 18 PowerShellMaxTenantConcurrency : PowerShellMaxCmdlets : PowerShellMaxCmdletsTimePeriod : ExchangeMaxCmdlets : PowerShellMaxCmdletQueueDepth : PowerShellMaxDestructiveCmdlets : PowerShellMaxDestructiveCmdletsTimePeriod : RCAMaxConcurrency : 1000 RCAPercentTimeInAD : 400 RCAPercentTimeInCAS : 400 RCAPercentTimeInMailboxRPC : 400 CPAMaxConcurrency : 20 CPAPercentTimeInCAS : 205 CPAPercentTimeInMailboxRPC : 200 MessageRateLimit : RecipientRateLimit : ForwardeeLimit : CPUStartPercent : 75 AdminDisplayName : ExchangeVersion : 0.10 (14.0.100.0) Name : TestMigrationThrottling DistinguishedName : CN=TestMigrationThrottling,CN=Global Settings,CN=Our Company,CN=Microsoft Exchange,CN=Services,CN=Configuration,DC=cimex,DC=com Identity : TestMigrationThrottling Guid : 240049b3-2023-4df1-8edc-fbfc1fc80b87 ObjectCategory : domain.com/Configuration/Schema/ms-Exch-Throttling-Policy ObjectClass : {top, msExchGenericPolicy, msExchThrottlingPolicy} WhenChanged : 21/04/2011 18:48:19 WhenCreated : 21/04/2011 18:07:20 WhenChangedUTC : 21/04/2011 17:48:19 WhenCreatedUTC : 21/04/2011 17:07:20 OrganizationId : OriginatingServer : a-domain-controller IsValid : True IMAPSettings RunspaceId : afa3159c-32a6-4906-986f-8adfbe50868b ProtocolName : IMAP4 Name : 1 MaxCommandSize : 10240 ShowHiddenFoldersEnabled : False UnencryptedOrTLSBindings : {192.168.x.x:143} SSLBindings : {192.168.x.x:993} InternalConnectionSettings : {mail.office.domain.com:143:TLS, mail.office.domain.com:993:SSL} ExternalConnectionSettings : {mail.office.domain.com:143:TLS, mail.office.domain.com:993:SSL} X509CertificateName : mail.domain.com Banner : The Microsoft Exchange IMAP4 service is ready. LoginType : SecureLogin AuthenticatedConnectionTimeout : 00:30:00 PreAuthenticatedConnectionTimeout : 00:01:00 MaxConnections : 2147483647 MaxConnectionFromSingleIP : 2147483647 MaxConnectionsPerUser : 16 MessageRetrievalMimeFormat : BestBodyFormat ProxyTargetPort : 143 CalendarItemRetrievalOption : iCalendar OwaServerUrl : EnableExactRFC822Size : False LiveIdBasicAuthReplacement : False SuppressReadReceipt : False ProtocolLogEnabled : True EnforceCertificateErrors : False LogFileLocation : C:\Program Files\Microsoft\Exchange Server\V14\Logging\Imap4 LogFileRollOverSettings : Daily LogPerFileSizeQuota : 0 B (0 bytes) ExtendedProtectionPolicy : None EnableGSSAPIAndNTLMAuth : True Server : CMX-OFFICE-EX01 AdminDisplayName : ExchangeVersion : 0.10 (14.0.100.0) DistinguishedName : CN=1,CN=IMAP4,CN=Protocols,CN=EXCHANGE01,CN=Servers,CN=Exchange Administrative Group (FYDIBOHF23SPDLT),CN=Administrative Groups,CN=Our COmpany,CN=Microsoft Exchange,CN=Services,CN=Configuration,DC=domain,DC=com Identity : EXCHANGE01\1 Guid : 48f9dc37-74c2-4fb0-a042-641f863f45f2 ObjectCategory : domain.com/Configuration/Schema/ms-Exch-Protocol-Cfg-IMAP-Server ObjectClass : {top, protocolCfg, protocolCfgIMAP, protocolCfgIMAPServer} WhenChanged : 21/04/2011 17:03:39 WhenCreated : 15/04/2011 13:51:58 WhenChangedUTC : 21/04/2011 16:03:39 WhenCreatedUTC : 15/04/2011 12:51:58 OrganizationId : OriginatingServer : a-domain-server IsValid : True

    Read the article

  • Launchd item no longer firing in Snow Leopard

    - by ridogi
    A launchd item that was working in 10.5 is no longer working after my upgrade to 10.6. I am running 10.6.2 and I have recreated the launchd item and given it a new name and that one doesn't run either. I have found a link of people with the same problem on google groups but none of the advice in that link helps. My launchd item is not listed in /private/var/db/launchd.db/com.apple.launchd/overrides.plist or in any of the overrides.plist files in the subdirectories of /private/var/db/launchd.db/ I have also tried to set this up as both a user agent and a user daemon. My launchd item simply runs a shell script, which I have no problem launching manually. <?xml version="1.0" encoding="UTF-8"?> <!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd"> <plist version="1.0"> <dict> <key>Label</key> <string>com.eric.tmnotify.launchd</string> <key>ProgramArguments</key> <array> <string>/<path_to>/tmnotify.sh</string> </array> <key>StartInterval</key> <integer>3600</integer> </dict> </plist> I have tried to load it by overriding the disabled key (even though it is not disabled in any of the overrides.plist files) with both: sudo launchctl load -F /Users/eric/Library/LaunchAgents/com.eric.tmnotify.launchd.plist sudo launchctl load -w /Users/eric/Library/LaunchAgents/com.eric.tmnotify.launchd.plist and after running either of them I can see that it is running by using sudo launchctl list but the shell script never fires. Edit: I have also put this in the formerly blank file at /private/var/db/launchd.db/com.apple.launchd.peruser.501/overrides.plist : <?xml version="1.0" encoding="UTF-8"?> <!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd"> <plist version="1.0"> <dict> <key>com.eric.tmnotify.launchd</key> <dict> <key>Disabled</key> <false/> </dict> </dict> </plist> I also tried inserting this alphabetically: <key>com.eric.tmnotify.launchd</key> <dict> <key>Disabled</key> <false/> </dict> into the file /private/var/db/launchd.db/com.apple.launchd/overrides.plist but still no dice.

    Read the article

  • Automatic layout of manual network mapping

    - by Paul
    So I have a small business network mainly consisting of two routed layer-2 domains with a total of ca. 100 devices spread over ca. 2000m² production and office spaces. Typical problems to solve using the graph would be: Over what (cable) path is a PC connected to the server? Where to expect devices connected to a switch port? I want to generate a graph of the physical network topology: Nodes are endpoint devices, switch ports, wall outlets, patch panel ports etc. Edges are cable connections. Ideally, grouping edges (or segments) that pass through the same bundle could be grouped. Also I would like to augment the graph data with automatically gathered data (monitoring state, MAC address, Switch port <- MAC entries to build up parts of the map). At the moment I use graphviz for this inside a Confluence wiki like that: layout = "neato" overlap = scale subgraph { rankdir = "TB" subgraph cluster_r1pf1 { r1pf1 [label="{ Rack 1 PF 1 | { <p1>P1 | <p2>P2 | <p3>P3} }", shape=record] } subgraph cluster_switch1 { switch1 [label="{ Rack 1 Switch 1 | { <p1> P1 | <p1> P1 | <p3> P3} }", shape=record] } r1pf1:p1 -> switch1:p1 (obviously there are dozens of entries omitted here) Problem is: I have a hard time to influence graphviz to generate a bearable layout. Edges overlap so bad that you can't read the diagram anymore. The question is: What other tools (be it interactive like Visio, Omnigraffle or I/O-oriented like graphviz) exist that would allow an easily versionable (as in: Operates on a text file) documentation that is both machine and human readable and editable? Why not OmniGraffle or Visio? Well we don't have Macs and Visio is not available at the moment. To buy it I would need good arguments. Automation would be one of that. But last time I looked, versioning Visio files or even thinking about automatic handling was a nightmare. Related: Network Mapping Tools basically asks the same with a focus on generating the complete graph automatically (but without the need to document cabling connections) Recommendations for automatic computer inventory brings up links of "all-in-one" solutions

    Read the article

  • dd-wrt router firmware QoS troubleshooting

    - by Jeff Atwood
    I've been using the dd-wrt firmware on my router and I like it a lot! But -- I'm not sure the quality of service (QoS) is working on it. I have it set up as follows: http, port 80 -- Premium bittorrent, port 6969 -- Bulk https, port 443 -- Premium dns, port 53 -- Premium Per the QoS documentation, these levels are: bandwidth is allocated based on the following percentages of uplink and downlink values for each class: Exempt: 100mbps - ignores global limits. Premium: 75% - 100% Express: 15% - 100% Standard: 10% - 100% Bulk: 1.5% - 100% This doesn't entirely seem to work, though -- with busy torrents going I get major pauses in my web browsing which sucks! The QoS documentation gives some steps to check the QoS ... What you'll be interested to look at will be the first set of source and destination IP, including the port numbers. Next the presence of l7proto and the "mark" field. The entries indicate the current live connection QoS priority applied on them based on the "mark" field. The "mark" values correspond to the following Exempt: 100 Premium: 10 Express: 20 Standard: 30 Bulk: 40 (no QoS matched): 0 You may see "mark=0" for some l7proto service even though they are in configured in the list of QoS rules. This may mean that the layer 7 pattern matching system didn't match a new or changed header for that protocol. Custom service on port matches will usually take care of these. On port 6969 (bittorrent) I see a weird mixture of stuff with mark=0 and mark=40 like so cat /proc/net/ip_conntrack udp 17 105 src=98.162.182.42 dst=1.2.3.4 sport=64512 dport=6969 packets=3 bytes=290 src=10.0.0.2 dst=98.162.182.42 sport=6969 dport=64512 packets=4 bytes=202 [ASSURED] mark=0 secmark=0 use=1 tcp 6 117 TIME_WAIT src=98.248.173.174 dst=1.2.3.4 sport=51114 dport=6969 packets=12 bytes=704 src=10.0.0.2 dst=98.248.173.174 sport=6969 dport=51114 packets=10 bytes=440 [ASSURED] mark=40 secmark=0 use=1 tcp 6 598 ESTABLISHED src=165.132.128.201 dst=1.2.3.4 sport=57218 dport=6969 packets=8024 bytes=9919881 src=10.0.0.2 dst=165.132.128.201 sport=6969 dport=57218 packets=4211 bytes=239607 [ASSURED] mark=0 secmark=0 use=1 tcp 6 586 ESTABLISHED src=68.46.9.24 dst=1.2.3.4 sport=64688 dport=6969 packets=6 bytes=490 src=10.0.0.2 dst=68.46.9.24 sport=6969 dport=64688 packets=8 bytes=944 [ASSURED] mark=40 secmark=0 use=1 udp 17 45 src=222.254.228.38 dst=1.2.3.4 sport=25438 dport=6969 packets=5 bytes=454 src=10.0.0.2 dst=222.254.228.38 sport=6969 dport=25438 packets=3 bytes=154 [ASSURED] mark=0 secmark=0 use=1 ( full file visible at http://pastebin.com/AZE6EtWm ) I've been playing around with this log for a little while and I can't see any patterns! Why is some port 6969 bittorrent traffic tagged mark=0 (not matched) by dd-wrt's QoS while others are tagged mark=40 (Bulk) .. any ideas?

    Read the article

  • Real-time offline folder-to-folder backup application needed (Windows)

    - by niktech
    I recently started using Intel Matrix Storage RAID solution that allowed me to use my 5 1TB drives for two RAID volumes. First one a 1TB RAID 0 striped across all 5 drives and second one a RAID 5 across the rest of the free space on all drives (around 2.85TB usable space). The RAID 0 I use for OS, applications and games while the RAID 5 I use as a more-permanent type storage (photos, etc). Now I do realize that running the OS and applications on RAID 0 across 5 drives is very dangerous, which is what brings up the following question. Is there a reliable freeware realtime backup application that can backup a set of folders from one drive to another drive (no online backups needed)? I've already tried a few (Mozy, Yadis, Comodo Backup, GFI Backup, Idoo, Crash Plan) but none meet my requirements: Low CPU and RAM usage. Realtime Backups - as soon as a file is modified in the source folder, it is added to the backup queue which will be processed with the lowest priority when the CPU is idle. This backup queue should persist in cases of computer restarts (ie: the source and destination folders should always have the same set of files, except for the ones waiting in the backup queue). Incremental Backups - if only 10 bytes changed in a 1GB file, the app should only copy those 10 new bytes. Ability to back up locked and opened files (some apps, like Yadis, can't back up critical files like browser favorites). Ability to run as a service (no need for any user to log-in to have the app started). Optional requirements: Compression of the destination into a well-known format (RAR, Zip) that can be directly read without the use of the application. Preset source folders (such as Browser Favorites, Game Saves, Application Settings, etc). The idea is to use RAID 0 array as "semi-persistent RAM-like" storage which in case of a failure can be quickly rebuilt by reinstalling the OS, apps and games and copying over the settings, saves, favorites from the RAID 5. I'm also thinking of taking this RAID 0 as RAM idea to the extreme with SSDs (as soon as we get some nice 6Gb/s SATA III SSDs out there), where a couple of SSDs chained in RAID 0 will work as yet another semi-persistent cache layer sitting between the RAM and the HD. I'm just hoping there already exists an application that satisfies these requirements... otherwise I'll have to write one myself, which I would prefer not to do.

    Read the article

  • Very slow printing from print server

    - by evolvd
    Print server is a VM on Xen The VM is Windows 2003 32bit. During the issue the VM is not being taxed in anyway, cpu, memory, hd read/write, and network speed is all good. The problem that I see is the transfer of the print file from the print server to the printer. The 80Mb file is transferred from the client to the print server in about 2 minutes but then it takes about 2 hours for that file to be sent to the printer. I can't figure out why this would just start to happen. The printer is rebooted every evening and is just used for one large print job in the morning. The server has been rebooted with no effect I changed the spool option to send the entire spool to the server before printing starts and it had no effect. This printer problem did happen to come about after some changes to the Xen environment. The Xen servers changed from using HBA NIC cards to software iscsi and a new switch was put in. I don't think this is related to the problem since all the speeds on the VMs are better now. The changed happened on Saturday and the first print to this printer happened on Monday morning. I'm just putting that out there but like I said I don't think it is related but I don't want to rule it out. At this point I don't have many other options besides the physical layer. I can switch out network cable that goes to the printer and I might be able to print the same job to another printer. I wont be able to test those things out till this afternoon though. Any other ideas or test I could do to try to find the reason for the slow speed? I forgot to say that this is only happening when printing to this one printer. ===Update=== I found out that there are a few printers that currently have this issue, not just the one. There are over 30 printers on the server though so I know it's not happening to all of them. I printed a large pdf doc from the server and it was able to print at the normal speed. If the machine sends the large print request it gets to the server fine but then slow to get from the server to the printer. If sent directly from the printer it gets to the printer at the normal speed. The question now is why is there a speed difference when it comes from the machine and why would it start now?

    Read the article

  • Monitoring tools that can take high rate and high volume?

    - by Jon Watte
    We're using Cacti with RRDTool to monitor and graph about 100,000 counters spread across about 1,000 Linux-based nodes. However, our current setup generally only gives us 5-minute graphs (with some data being minute-based); we often make changes where seeing feedback in "near real time" would be of value. I'd like approximately a week of 5- or 10-second data, a year of 1-minute data, and 5 years of 10-minute data. I have SSD disks and a dual-hexa-core server to spare. I tried setting up a Graphite/carbon/whisper server, and had about 15 nodes pipe to it, but it only has "average" for the retention function when promoting to older buckets. This is almost useless -- I'd like min, max, average, standard deviation, and perhaps "total sum" and "number of samples" or perhaps "95th percentile" available. The developer claims there's a new back-end "in beta" that allows you to write your own function, but this appears to still only do 1:1 retention (when saving older data, you really want the statistics calculated into many streams from a single input. Also, "in beta" seems a little risky for this installation. If I'm wrong about this assumption, I'd be happy to be shown my error! I've heard Zabbix recommended, but it puts data into MySQL or some other SQL database. 100,000 counters on a 5 second interval means 20,000 tps, and while I have an SSD, I don't have an 8-way RAID-6 with battery backup cache, which I think I'd need for that to work out :-) Again, if that's actually something that's not a problem, I'd be happy to be shown the error of my ways. Also, can Zabbix do the single data stream - promote with statistics thing? Finally, Munin claims to have a new 2.0 coming out "in beta" right now, and it boasts custom retention plans. However, again, it's that "in beta" part -- has anyone used that for real, and at scale? How did it perform, if so? I'm almost thinking about using a graphing front-end (such as Graphite) and rolling my own retention backend with a simple layer on top of mmap() and some stats. That wouldn't be particularly hard, and would probably perform very well, letting the kernel figure out the balance between frequency of flushing to disk and process operations. Any other suggestions I should look into? Note: it has to have shown itself able to sustain the kinds of data loads I'm suggesting above; if you can point at the specific implementation you're referencing, so much the better!

    Read the article

  • How can I change how OS X's 'say' command pronounces a word?

    - by jwhitlock
    OS X's say command is useful for some tasks (such as Skype's 'notify me when a contact comes online), but it is pronouncing some names incorrectly. Is there a way to teach say to pronounce a word differently? For example, try: say "Hi, Joel Spolsky" The 'ol' sounds like 'ball' rather than 'old'. I'd like to add an exception that say "Pronounce Spolsky like this", rather than try to teach new linguistic rules. I bet there is a way since it can pronounce "iphone" as Apple wants. Update - After some research, here's what I've learned: Text-to-speech is split between turning the text to phonemes, and then the phonemes are turned into audio using a voice. Changing the voice doesn't effect the phonemes. The Speech Synthesis Manager has some functions for turning text to phonemes, and a method for registering a speech dictionary that will add new text-phoneme maps. However, Apple's speech dictionary must be in a binary form - I didn't find any plist XML. Using dtrace while running say, I found some interesting files opened in /System/Library/PrivateFrameworks/SpeechDictionary.framework/Resources. This is probably the speech dictionary, but they are all binary, except for Homophones, which is XML. Adding entries to Homophones does nothing - it is probably used in speech-to-text. They are also code signed by Apple - changing them may prevent some programs from working. PrefixDictionary CartNames CartLite SymbolDictionary Homophones There are ways to add text versions of application interface elements so VoiceOver works, a lot of which a developer gets for free, but there are tricky bits. The standard here appears to be to use a phonetic spelling as needed. My guesses are: say is a light layer of code on top of the Speech Synthesis Manager. It would be easy for the Apple devs to add a command line option to take the path to a speech dictionary plist for alternate phoneme mapping, but they didn't. It may be a useful open-source project to write a better say. Skype probably uses Speech Synthesis Manager directly, leaving no hooks to change the way my friend's names are pronounced, other than spelling them phonetically, which is silly. The easiest way to make a command line version of say is how JRobert suggested. Here's my quick implementation, using Doug Harris's spelling suggestion: #!/bin/sh echo $@ | tr '[A-Z]' '[a-z]' | sed "s/spolsky/spowlsky/g" | /usr/bin/say Finally, some fun command line stuff: # Apple is weird sqlite3 /System/Library/PrivateFrameworks/SpeechDictionary.framework/Resources/Tuples .dump # Get too much information about what files are being opened sudo dtrace -n 'syscall::open*:entry { printf("%s %s",execname,copyinstr(arg0)); }' # Just fun say -v bad "Joel Spolsky Spolsky Spolsky Spolsky Spolsky, Joel Spolsky Spolsky Spolsky Spolsky Spolsky" echo "scale=1000; 4*a(1)" | bc -l | say

    Read the article

  • Win-XP Browsers Hang on page load - (waiting for...)

    - by CHarmon
    Hello, I’m having problems with my browsers hanging on loading pages on my desktop machine. I’m using Windows XP Pro with SP3 and fully updated except for IE 8. All three of my browsers, IE 7, Chrome and Firefox are having the same problems. Pages are not being loaded and are hanging on “waiting for …”. The browsers are waiting for the page being loaded or ad servers. Sometimes a page will load but the loading graphic continues to be displayed as if the page were still loading when the page appears to be fully loaded. The problem is bad enough that I can’t really use any of my browsers. I can eventually get most pages to load by stopping and restarting the page load. I have DSL modem with a wireless router and I have been able to eliminate the modem and router from being the source of my problem. My laptop doesn’t have any problems even when hardwired to the router and with the wireless connection disabled. I deleted the NIC and let XP re-install. Also tried a different network cable. Tried the same router port used in the laptop test. One clue that may be important is that I can’t connect to my router using the desktop machine…the page hangs while trying to connect. I can ping the router and I can quickly connect to the router using the laptop. I also can’t use the Windows update process – the page never fully loads. The problem affects other user accounts and even happens in safe mode. I am convinced the problem is with part of the O/S…some layer able to affect all of the browsers. The purpose of this post is to see if anyone has some ideas before I do a XP repair. I have done quite a bit of trouble-shooting: Ran a full anti-virus scan with AVG – no problems. Ran full scans with Spybot, MalwareBytes and Sophos anti-rootkit – no problems. Ran Chkdsk with both options checked. Ran Disk Clean up Defragged RE-installed IE7 Cleared all the browser caches Ran Ccleaner (registry tool) Ran HijackThis – nothing unusual (problem happens in safe mode too) Ran Process Explorer – no unusual processes Used System Restore and fell back several days – no change in the problem Booted to last known good configuration – no change in the problem Ran MicrosoftFixit50199.msi – no change in the problem Any ideas or suggestions would be appreciated…I’m not looking forward to doing a repair on XP. Thanks in advance for any help.

    Read the article

  • PHP hits 100% CPU and eats RAM at the same time Monday to Friday

    - by Daniel Samuels
    We run a learning platform for primary schools here in the UK and it's all been running extremely well. However at around 4PM Monday to Friday we see the same issue arise -- 1-2 PHP threads will spike to 100% CPU and gradually start eating up RAM until the server(s) fall over. 98%+ of our requests are HTTPS, these come into our Layer 7 load balancer which then decrypts the SSL data, adds the X-HTTP-Forwarded-For header and forwards the data onto an application server (we have 2 of those at the moment) on port 80. Our application servers have Varnish on port 80 which takes in the request from the load balancer and passes the request through to Nginx on port 81. Nginx then works out which 'vhost' it needs to use and passes any PHP processing through to PHP-CGI which is listening on a socket (managed through spawn-fcgi). There's an instance of Memcached running too, MySQL runs on a separate server / slave setup. Throughout the day the load will typically go no higher than 0.8 on either of the application servers, however at around 4PM our problem arises. I've managed to run strace on a few of the actual threads when they cause the problem and I always see the same thing: stat("/usr/share/zoneinfo/Europe/London", {st_mode=S_IFREG|0644,st_size=3661, ...}) = 0 stat("/usr/share/zoneinfo/Europe/London", {st_mode=S_IFREG|0644,st_size=3661, ...}) = 0 This is repeated infinitely and never stops until you SEGKILL the process or oomkiller kills it. There are no cron jobs scheduled to run at that time and I don't have any way of seeing exactly what Nginx request is associated with the PHP process which is running. We are running PHP 5.3.14 which we upgraded to from 5.3.8 last week to rule out the older version being the problem. This issue has been going on a few months now and we have no idea what is causing it. We deploy our software very frequently, so it's difficult to track down a specific release which may have started the problem - especially as we do not know the date of the first occurrence of this issue. Varnish is version 3.0.1, Nginx is 1.0.6 (which I understand is about a year old now), our servers are running CentOS release 5.7 (Final) they have Intel i3 540s at 3.07Ghz and 8GB of RAM. There's a discussion on the Debian mailing list about something very similar, you can find that here. Has anyone seen anything like this in the past, does anyone have any ideas or suggestions? Are there a way of linking an Nginx request directly to a PHP thread? Is there a better way of seeing what the PHP process is doing? (I've seen GDB mentioned, though I'll have to recompile PHP) Thanks!

    Read the article

< Previous Page | 229 230 231 232 233 234 235 236 237 238 239 240  | Next Page >