Search Results

Search found 12705 results on 509 pages for 'ip routing'.

Page 235/509 | < Previous Page | 231 232 233 234 235 236 237 238 239 240 241 242  | Next Page >

• Remote location looses connectivity

  - by user24559

  I have a remote location that has constant internet access using DSL. The remote location only has three Linksys cameras that use the internet access with a router. There is no computer on the network. The router is configured to use the DYN.org service to keep the IP address updated if the internet provider assigns a new ip address. The problem I am having is the router after a period of time stops responding to incoming ping requests and the cameras are shown offline. However, if I keep one of the cameras constantly streaming data then the connection to all the cameras works just fine all the time. How can I keep the router from appearing to be sleeping and not responding to incoming requests? The router is the Linksys WRT300N.

  Read the article

• Remote Desktop over SSH SOCKS proxy to bypass firewall

  - by scrumpyjack

  Hi folks, I'm trying to connect to a Windows server from my Mac using RDC2.1 for Mac. The problem is the server I need to connect to is guarded by the evil dragon - IP-based access control on a completely separate network. I have an IP I can get in on, but it's at my office (i.e. a completely separate network). Because that network isn't set up for VPN, I've set up a SOCKS proxy through an SSH tunnel (which is all working fine). (SSH proxy) Me (on my Mac) ----------> Office Linux box ----> Windows server (home network) (office network) (other network) From my Linux server in my office (the SSH server) I can telnet to port 3389 on the Windows server, no problem. But from my Mac I can't get so much as a squeak out of it. Any ideas?

  Read the article

• When connected through a router, a new gateway appears, and I lose my internet connection.

  - by idan315

  I have two computers connected to a router, connected to my ADSL modem by PPPoE. One of those computrs use Windows XP, the other uses Windows 7. The computer using Windows 7 keeps getting limited or no connectivity, and I can't use it to connect to the internet. Connecting the computer to the modem without the router 'in the way' worked, and I was able to use the internet - which led me to believe that the problem is with my router. However, I have changed my router, and the problem persists. (Just to be clear: the computer using Windows XP can connect to the internet without any problem). This entire question is about the PC using Windows 7. The only symptom of this problem is that when I see my network devices, in addition to my router (which appears as "Network 4", or something of the sort), I also see an "Unidentified Network". When using ipconfig to check the problem, I see a second gateway, with the IP 0.0.0.0, in addition to the IP of my router.

  Read the article

• Nginx & Apache Cannot get try_files to work with permalinks

  - by tcherokee

  I have been working on this for the past two weeks not and for some reason I cannot seem to get nginx's try_files to work with my wordpress permalinks. I am hoping someone will be able to tell me where I am going wrong and also hopefully tell me if I made any major errors with my configurations as well (I am an nginx newbie... but learning :) ). Here are my Configuration files nginx.conf user www-data; worker_processes 4; pid /var/run/nginx.pid; events { worker_connections 768; # multi_accept on; } http { ## # Basic Settings ## sendfile on; tcp_nopush on; tcp_nodelay on; keepalive_timeout 65; types_hash_max_size 2048; # server_tokens off; # server_names_hash_bucket_size 64; # server_name_in_redirect off; include /etc/nginx/mime.types; default_type application/octet-stream; ## # Logging Settings ## # Defines the cache log format, cache log location # and the main access log location. log_format cache '***$time_local ' '$upstream_cache_status ' 'Cache-Control: $upstream_http_cache_control ' 'Expires: $upstream_http_expires ' '$host ' '"$request" ($status) ' '"$http_user_agent" ' ; access_log /var/log/nginx/access.log; error_log /var/log/nginx/error.log; include /etc/nginx/conf.d/*.conf; include /etc/nginx/sites-enabled/*; } mydomain.com.conf server { listen 123.456.78.901:80; # IP goes here. server_name www.mydomain.com mydomain.com; #root /var/www/mydomain.com/prod; index index.php; ## mydomain.com -> www.mydomain.com (301 - Permanent) if ($host !~* ^(www|dev)) { rewrite ^/(.*)$ $scheme://www.$host/$1 permanent; } # Add trailing slash to */wp-admin requests. rewrite /wp-admin$ $scheme://$host$uri/ permanent; # All media (including uploaded) is under wp-content/ so # instead of caching the response from apache, we're just # going to use nginx to serve directly from there. location ~* ^/(wp-content|wp-includes)/(.*)\.(jpg|png|gif|jpeg|css|js|m$ root /var/www/mydomain.com/prod; } # Don't cache these pages. location ~* ^/(wp-admin|wp-login.php) { proxy_pass http://backend; } location / { if ($http_cookie ~* "wordpress_logged_in_[^=]*=([^%]+)%7C") { set $do_not_cache 1; } proxy_cache_key "$scheme://$host$request_uri $do_not_cache"; proxy_cache main; proxy_pass http://backend; proxy_cache_valid 30m; # 200, 301 and 302 will be cached. # Fallback to stale cache on certain errors. # 503 is deliberately missing, if we're down for maintenance # we want the page to display. #try_files $uri $uri/ /index.php?q=$uri$args; #try_files $uri =404; proxy_cache_use_stale error timeout invalid_header http_500 http_502 http_504 http_404; } # Cache purge URL - works in tandem with WP plugin. # location ~ /purge(/.*) { # proxy_cache_purge main "$scheme://$host$1"; # } # No access to .htaccess files. location ~ /\.ht { deny all; } } # End server gzip.conf # Gzip Configuration. gzip on; gzip_disable msie6; gzip_static on; gzip_comp_level 4; gzip_proxied any; gzip_types text/plain text/css application/x-javascript text/xml application/xml application/xml+rss text/javascript; proxy.conf # Set proxy headers for the passthrough proxy_redirect off; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_max_temp_file_size 0; client_max_body_size 10m; client_body_buffer_size 128k; proxy_connect_timeout 90; proxy_send_timeout 90; proxy_read_timeout 90; proxy_buffer_size 4k; proxy_buffers 4 32k; proxy_busy_buffers_size 64k; proxy_temp_file_write_size 64k; add_header X-Cache-Status $upstream_cache_status; backend.conf upstream backend { # Defines backends. # Extracting here makes it easier to load balance # in the future. Needs to be specific IP as Plesk # doesn't have Apache listening on localhost. ip_hash; server 127.0.0.1:8001; # IP goes here. } cache.conf # Proxy cache and temp configuration. proxy_cache_path /var/www/nginx_cache levels=1:2 keys_zone=main:10m max_size=1g inactive=30m; proxy_temp_path /var/www/nginx_temp; proxy_cache_key "$scheme://$host$request_uri"; proxy_redirect off; # Cache different return codes for different lengths of time # We cached normal pages for 10 minutes proxy_cache_valid 200 302 10m; proxy_cache_valid 404 1m; The two commented out try_files in location \ of the mydomain config files are the ones I tried. This error I found in the error log can be found below. ...rewrite or internal redirection cycle while internally redirecting to "/index.php" Thanks in advance

  Read the article

• Mac | Port Forwarding for Remote Desktop

  - by Vaibhav Bajpai

  I have two Mac notebooks at home, I have assigned them static private IPs. I have also set my router to a DynDNS address, which updates everytime my router gets a new public IP. I have enabled Screen Sharing on both notebooks. I can successfully goto my router webpage using the DynDNS address. I understand I need to port-forward to get Screen Sharing to work from outside. Lets assume, notebooks have private IP 192.168.1.2 and 192.168.1.3 I am kind of lost here, would appreciate some help (I need to be able remote desktop to both notebooks)

  Read the article

• why udp client work when wirshark capture?

  - by herzl shemuelian

  I have two machine A,B windows 7 os .I connect them end to end and try run a performance test by using tcpreplay. step 1) I check conectivity between to point by netcat In A i run nc -lvup 5432 when I run on B nc -u 1.2.3.4 5432 I can send data from B to A step 2) when in I run tcpreplay in B tcpreplay -i %0 myudp.pcap in A I don't recevice any data . when I open wireshark in A then my nc can read data why? I check dst mac and dst ip in pcap file they are correct. is importan udp src mac or src ip for udp how that I open udp server ?

  Read the article

• Troubleshoot telnet connection from Windows 7 to UNIX

  - by Sujay Ghosh

  I am trying to connect to an Asterisk server in USA. I am using telnet < IP Address 5038 from India to USA. The person in USA is able to telnet to the IP address and port from USA , but I am not able to do it from India. We are on different networks. I am using Windows 7 Ultimate, and have enabled the Telnet client. I have also used Putty without any success. Can someone suggest me what can be the problem and how can this be resolved.

  Read the article

• set tap0 using virt-manager for bridged wireless

  - by DaveO

  After 3 days I finally have kvm guests working on the network via wireless (link below - thanks!): My network is 192.168.1.0/24 on the host: sudo sh -c "echo 1 > /proc/sys/net/ipv4/ip_forward" sudo tunctl -t tap0 sudo ip link set tap0 up sudo ip addr add 192.168.1.25/24 dev tap0 sudo route add -host 192.168.1.30 dev tap0 sudo parprouted wlan0 tap0 on the guest: auto eth0 iface eth0 inet static address 192.168.1.30 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 gateway 192.168.1.25 and start the guest: sudo kvm /path/to/guest.img -net nic,macaddr=DE:AD:BE:EF:90:26 -net tap,ifname=tap0,script=no This works great and I can ping the local network and the internet back and forth between the guest. But how do I add these settings to the guest's xml config so I can start the guest via virt-manager with the same nic settings? ref: http://www.linuxquestions.org/questions/debian-26/kvm-wireless-bridge-network-691953/

  Read the article

• forwardfor information is missing

  - by FAFA

  I use following configuration to load balance https connections, using haproxy 1.4.8. SSL offloading is done by apache. listen ssl_to_waf 192.168.101.54:443 mode tcp balance roundrobin option ssl-hello-chk server wafA 192.168.101.61:444 check listen ssl_from_waf 192.168.101.61:445 balance roundrobin option forwardfor server webA 192.168.101.46:80 check For HTTP requests this works great, requests are distributed to my Apache servers just fine. But for HTTPS request, I lose the "forwardfor" information. I need to save the client IP address. How can I use HAproxy to load balance across a number of SSL servers, allowing those servers to know the client's IP address?

  Read the article

• Sharing Internet Connection in Windows 7 is so much more frustrated than Windows XP

  - by Phuong Nguyen

  Back to the time of Windows XP, from Properties dialog of my Wireless Connection, I can enable sharing and then select LAN network from the Drop Down List and boom, I can share it with my friend. We just need a LAN cable (either cross or not-cross is OK) and his Laptop will get an auto IP to gain access to internet. But now with the new Windows 7, everything starts to suck. I cannot see the Drop Down List any more in the sharing panel and my friends Laptop cannot get an automatic IP anymore. Am I doing anything wrong over there? How can I gain back the peace I used to have with Windows XP?

  Read the article

• Configuring Linux Network

  - by Reiler

  Hi I'm working on some software, that runs on a Centos 5.xx installation. I'ts not allowed for our customers to log in to Linux, everything is done from Windows applications, developed by us. So we have build a frontend for the user to configure network setup: Static/DHCP, ip-address, gateway, DNS, Hostname. Right now I let the user enter the information in the Windows app, and then write it on the Linux server like this: Write to /etc/resolv.conf: Nameserver Write to /etc/sysconfig/network: Gateway and Hostname Write to /etc/sysconfig/network-scripts/ifcfg-eth0: Ipaddress, Netmask, Bootproto(DHCP or Static) I also (after some time) found out that I was unable to send mail, unless I wrote in /etc/hosts: 127.0.0.1 Hostname All this seems to work, but is there a better/easier way to do this? Also, I read the network configuration nearly the same way, but if I use DHCP, I miss som information, for instance the Ip-address. I know that I can get some information from the commandline (ifconfig), but I dont get for instance Hostname, Gateway and DNS. Is there a commandline tool that will display this?

  Read the article

• Server 2008/Windows 7/Samba Unspecified error 80004005

  - by ancillary

  I have a Samba share on a LAN with 2008 PDC/DNS. Smb authenticates with AD and I have several Win7 Machines that can connect fine. I recently added a couple of new computers to the LAN which were imaged the same way (same software, etc.; different hardware so different drivers) as the other machines and they have the same policies set. I can not get the new machines to connect to the samba share no matter what. I am always met with either Unspecified Error 0x80004005 or Network Path not found. I've turned off the firewall; set LANMAN auth to respond to NTLM only/send LM & NTLM responses/use NTLM session security if negotiated in Local Sec Policy SEcurity Options; tried both ip and hostname to connect. SMB log shows that authentication succeeds; but then connection is immediately killed by the client. tcpdump shows nothing remarkable except that when trying to connect from the client via hostname there is an unknown packet type error: ack 201 win 255 NBT Session Packet: Unknown packet type 0xABData: (41 bytes) Here's a couple of lines from that error: 11:18:37.964991 IP 001-client.domain.local.49372 > smb.domain.local.netbios-ssn: P 1670:2146(476) ack 201 win 255 NBT Session Packet: Unknown packet type 0xABData: (41 bytes) [000] AA 46 96 FA D5 99 33 75 0C C4 20 CE 26 42 F3 61 \252F\226\372\325\2313u \014\304 \316&B\363a [010] F0 8C FB 65 18 17 40 A5 DB 42 BB 94 37 53 92 EC \360\214\373e\030\027@\245 \333B\273\2247S\222\354 [020] 55 98 7F C4 AE 3D 6B 10 C4 U\230\177\304\256=k\020 \304 11:18:37.964998 IP smb.domain.local.netbios-ssn > 001-client.domain.local.49372: . ack 2146 win 100 Here's smb.conf just in case (though don't see how if other machines are working fine): [global] workgroup = MYDOMAIN realm = MYDOMAIN.LOCAL server string = domain|smb share interfaces = eth1 security = ADS password server = 192.168.1.3 log level = 2 log file = /var/log/samba/%m.log smb ports = 139 strict locking = no load printers = No local master = No domain master = No wins server = 192.168.1.3 wins support = Yes idmap uid = 500-10000000 idmap gid = 500-10000000 winbind separator = + winbind enum users = Yes winbind enum groups = Yes winbind use default domain = Yes [samba-share1] comment = SMB Share path = /home/share/smb/ valid users = @"MYDOMAIN+Domain Users" admin users = @"MYDOMAIN+Domain Admins" guest ok = no read only = No create mask = 0765 force directory mode = 0777 Any ideas what else I could try or look for? Or what might be the problem? Thanks.

  Read the article

• Cannot access SWITCH thru VPN

  - by MadBoy

  I've VPN connection set up that i connect to company with. I can connect to all devices (other switches, routers, servers from same subnet with same settings just diffrent ip) but I can't connect to NetGear Router GS748Tv3. Settings on switch: IP address 192.168.1.8 Subnet mask 255.255.255.0 Default gateway 192.168.1.1 Management VLAN ID: 0 (1 - 4094 or 0) (0 means all VLANs) Switch has 2 VLAN's configured 1 and 2. I can access this switch thru VPN if i log in to server and from server to switch but this is a little bit slower then normal way. Anything I'm missing?

  Read the article

• set tap0 using virt-manager for bridged wireless

  - by DaveO

  After 3 days I finally have kvm guests working on the network via wireless (link below - thanks!): My network is 192.168.1.0/24 on the host: sudo sh -c "echo 1 > /proc/sys/net/ipv4/ip_forward" sudo tunctl -t tap0 sudo ip link set tap0 up sudo ip addr add 192.168.1.25/24 dev tap0 sudo route add -host 192.168.1.30 dev tap0 sudo parprouted wlan0 tap0 on the guest: auto eth0 iface eth0 inet static address 192.168.1.30 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 gateway 192.168.1.25 and start the guest: sudo kvm /path/to/guest.img -net nic,macaddr=DE:AD:BE:EF:90:26 -net tap,ifname=tap0,script=no This works great and I can ping the local network and the internet back and forth between the guest. But how do I add these settings to the guest's xml config so I can start the guest via virt-manager with the same nic settings? ref: http://www.linuxquestions.org/questions/debian-26/kvm-wireless-bridge-network-691953/

  Read the article

• Setup IIS 7 as FTP Server that is connectable outside of my local network

  - by Usta

  I was able to setup an FTP site that I was able to access via ftp://127.0.0.1/ or my local(static) ip. To do this I followed these instructions (with the exception that I did not bind to 127.0.0.1 as suggested) http://learn.iis.net/page.aspx/301/creating-a-new-ftp-site-in-iis-7/ I have created a firewall exception for port 20 and 21, and setup port-forwarding on my wireless router. But I can only access the site via local-host, and I need to have a friend have read access to it. So how do I enable remote access to it? (I'd rather not purchase a domain-name) My setup: IIS 7.5 Windows 7 Professional Wireless Network Norton Internet Security 2012 An Internal Static IP Address

  Read the article

• Share internet with my phone?

  - by Kenneth Cochran

  Most people want to use their cellphone as a modem for their computer, commonly referred to as 'tethering'. I'm actually interested in doing the opposite: Sharing my landline internet connection(which is much faster than any 3G service) with by cellphone. My phone is a Verizon BlackBerry Curve 8330 and it has USB and bluetooth connections. I know both USB and Bluetooth are capable of supporting tcp/ip traffic what's not so clear is: Is IP over USB or Bluetooth standardized? Is it supported on my phone? Has my cellphone company crippled my phone to prevent me from using it?

  Read the article

• How to test DNS glue record?

  - by Sunnz

  Hello I have just set up a DNS server for my domain example.org with 2 name servers ns1.example.org and ns2.example.org. I have attempted to set up a glue record for ns1 and ns2 at my registrar. It seems to work for now when I do a dig example.org but when I do a whois example.org it lists ns1.example.org and ns2.example.org but not their IP address which should be set up as a glue record. So I am wondering how do I check for the existence of a glue record? Do I do it with whois? I have seen .com and .net whois records that have both the domain name as well as the IP address for the name servers, is .org different? What's the proper way to test this? Thanks.

  Read the article

• Port forwarding not working?

  - by rphello101

  I'm trying to set up an Apache Server to be accessed publicly. I'm using a Netgear R4500 router hooked up to a Motorola SB6121 modem. I can access my server on my computer by typing in my IP address. After following the instructions to forward port 80 so I can access the server from other computers, it does not work (see image). I get "This webpage is not available". I am forwarding to the IP address of my computer. Using this Network Port Scanner Tool, it says "80/tcp filtered http", which, as I understand it, means forwarding did not work correctly. In my Apache httpd file, I have: ServerName 192.168.1.13:80 and Listen 192.168.1.13:80 Anyone know what's wrong or have something I can try? click to enlarge

  Read the article

• How to do complex port forwarding (sort of)

  - by adnan kamili

  I have a very different situation. My laptop named A, another machine B(ip-172.16.28.3) with ssh server installed and i have an account on that machine, the third machine C(ip-172.16.24.3) is a proxy server. All the machines are within a LAN, but 1- Machine B can connect to A as well as C 2- Machine A i.e.my pc, it can only connect to B and not C Now to use internet, i do the following: ssh -X [email protected] Then i type firefox and i use the firefox of machine B with proxy setings as 172.16.24.3:3128 Instead of using firefox of B, i want to use my local firefox. Is there a way through which i can connect to C via B and use my local firefox for browsing

  Read the article

• Slow Starting DHCP Client Service - HP Thin Clients

  - by Ryan

  We have recently began adding XPe thin clients to our domain in preperation for a new citrix environment. One thing that has been picked up on in testing is that they appear slow to boot. The issue manifest's it's self as the classic "Applying Computer Settings..." screen we are all used to seeing. After digging into the issue it appears the DHCP Client service is taking some time to load on boot, this varies but I would estimate it can take around 1 minute in some cases. I've eliminated the classic issues, DHCP is responding correctly and in quick time. DNS is not the cause and GPO's are applying promptly. A simple workaround is to assign the client a static IP which work's great so the TCP/IP servies are obviously firing up quickly, just not DHCP Client. Does anyone have any idea's on how I may be able to improve the service start time? Keen to find a better solution before I get my arm twisted into setting up 250 thin clients with static addressing!

  Read the article

• Why can't I connect to remote Microsoft SQL Server through SSH tunnel?

  - by Alexander

  I have at home a D-Link DIR-615 C1 router with DD-WRT. I set up the SSH server on the router, and log on through an SSH2-RSA passphrase-protected key. That router is the gateway between the local network and the internet. One of the computers on that network has Microsoft SQL Server 2008 installed, with TCP/IP protocol enabled through port 1433. I've set up port forwarding on the router, so that remote connections are possible and are, in fact, working (some developers log on remotely without problems). I am part of another network, that has internet access through a proxy server, which only has ports 80 and 443 opened. I can't connect to that MSSQL server on that remote server because 1433 port is closed on this network. I connected (using Putty) through 443 port to my router's SSH server, and set up 2 tunnels. One is for RDP (3389), and it's working. The other is for 1433 port, to connect to the server. I can't connect through the SSH tunnel to the MS SQL Server, neither through telnet, or through GUI clients. Am I missing something? Additional details: on connect, I get this error from SQL Server Management Studio: TITLE: Connect to Server Cannot connect to localhost:14330. ADDITIONAL INFORMATION: A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: Named Pipes Provider, error: 40 - Could not open a connection to SQL Server) (Microsoft SQL Server, Error: 3) For help, click: http://go.microsoft.com/fwlink?ProdName=Microsoft+SQL+Server&EvtSrc=MSSQLServer&EvtID=3&LinkId=20476 BUTTONS: OK The tunnel is configured like this: L14330 192.168.0.103:1433 192.168.0.103 is the permanent address of the SQL Server on the LAN. I also successfully forwarded TCP traffic of 3389 port to that IP, so tunneling is working to that IP address. When connecting without tunnel, through Microsoft SQL Server Management Studio, using the same method the connection establishes. Too bad my proxy doesn't allow 1433 port traffic, I wouldn't have this headache.

  Read the article

• BIND DNS server (Windows) - Unable to access my local domain from other computers on LAN

  - by Ricardo Saraiva

  I have a BIND DNS server running on my Windows 7 development machine and I'm serving pages with WAMPSERVER. My ideia is to develop some tools (in PHP) for my intranet at work and I want them to be accessible via LAN in this format: http://tools.mycompany.com I've already placed BIND and I can access http://tools.mycompany.com on the machine that holds BIND server, but I cannot access it from other LAN computers. I've done the following on my router: defined static IP's for all LAN computers set Port Forwarding to my server (remember: it serves DNS and Web pages) set DNS server configuration to point to my LAN server On LAN computers, I went to Local Area Network properties and also changed the DNS server IP in order to point to my local DNS server. If it helps, here is my named.conf file: options { directory "c:\windows\SysWOW64\dns\etc"; forwarders {127.0.0.1; 8.8.8.8; 8.8.4.4;}; pid-file "run\named.pid"; allow-transfer { none; }; recursion no; }; logging{ channel my_log{ file "log\named.log" versions 3 size 2m; severity info; print-time yes; print-severity yes; print-category yes; }; category default{ my_log; }; }; zone "mycompany.com" IN { type master; file "zones\db.mycompany.com.txt"; allow-transfer { none; }; }; key "rndc-key" { algorithm hmac-md5; secret "qfApxn0NxXiaacFHpI86Rg=="; }; controls { inet 127.0.0.1 port 953 allow { 127.0.0.1; } keys { "rndc-key"; }; }; ...and a single zone I've defined - file db.mycompany.com.txt: $TTL 6h @ IN SOA tools.mycompany.com. hostmaster.mycompany.com. ( 2014042601 10800 3600 604800 86400 ) @ NS tools.mycompany.com. tools IN A 192.168.1.4 www IN A 192.168.1.4 On the file above 192.168.1.4 is the IP of the local machine inside my LAN. Can someone help me here? I need my web pages to be accessible from other computers inside my LAN using my custom domain name. I've tried on other computers and they can access my server via http://192.168.1.4/, but no able when using http://tools.mycompany.com . Please, consider the following: I'm completely new to BIND I have basic knowledge in Apache configuration Thanks a lot for your help.

  Read the article

• Icinga/Nagios to ping different machine on local network

  - by feronovak

  I have 3 machines, all remote IPs and all of them running nsclient++ with remote and local IP addresses: 46.*.*.1/192.168.1.1 46.*.*.2/192.168.1.2 46.*.*.3/192.168.1.3 I want nagios/icinga to remotely ping other local machines to see whether VLAN is working correctly. Is there a way to tell nagios/icinga to use machine 192.168.1.1 and to ping 192.168.1.2 and 192.168.1.3 ? check_ping is pinging only machine defined in host_name from icinga server. Icinga is on completely different ip range 92.*.*.* Is there a way to do this to see VLAN workes fine?

  Read the article

• Is SYN flooding still a threat?

  - by Rob

  Well recently I've been reading about different Denial of Service methods. One method that kind of stuck out was SYN flooding. I'm a member of some not-so-nice forums, and someone was selling a python script that would DoS a server using SYN packets with a spoofed IP address. However, if you sent a SYN packet to a server, with a spoofed IP address, the target server would return the SYN/ACK packet to the host that was spoofed. In which case, wouldn't the spoofed host return an RST packet, thus negating the 75 second long-wait, and ultimately failing in its attempt to DoS the server?

  Read the article

• Virtual Private Hosting DNS configuration

  - by Ciel

  I did a great deal of reading here before posting this because I didn't want to post a duplicate - but I'm on a bit of a deadline and getting frustrated, so here goes... I very, very, very sincerely apologize if this is long winded or hard to read. Please - please just ask for any information or clarification and I will give it as quickly as I possibly can. This has become very frustrating to me and this is the last place I know to turn. I have no experience with setting up DNS, no experience with nameservers, and no peers to go to for help. So this is kind of my last ditch effort. The task of setting up a private server has, through circumstances beyond my control, fallen into my lap. I own a domain (hereafter referred to as yyy.com) and have always used shared hosting - I buy a package and just point it to the domain nameservers they give me. It's always been simple. yyy.com is registered with network solutions Now I have purchased a Virtual Private Hosting package from GoDaddy.com - and it comes with Plesk 11. I have no earthly idea how to begin to get the right nameserver for yyy.com. I have gone through the instructions and have wound up exceedingly frustrated. I have 2 IP addresses from GoDaddy for the server. This is what I have so far, and I cannot tell if it is working (Since propogation takes so long, it is extremely hard to test for me) IP 1 : XX.XX.XX.XX IP 2 : YY.YY.YY.YY (obviously hidden for privacy) Now after going through the documentation setup and waiting a few days, this is the setup I have - and so far it does not appear to be working. Host Record type Value XX.XX.XX.XX / 24 PTR yyy.com. yyy.com. NS ns1.yyy.com. yyy.com. A XX.XX.XX.XX yyy.com. MX (10) mail.yyy.com. ftp.yyy.com. CNAME yyy.com. ipv4.yyy.com. A XX.XX.XX.XX mail.yyy.com. A XX.XX.XX.XX mssql.yyy.com. A XX.XX.XX.XX ns1.yyy.com. A XX.XX.XX.XX ns2.yyy.com. A YY.YY.YY.YY webmail.yyy.com. A XX.XX.XX.XX www.yyy.com. CNAME yyy.com. yyy.com is pointing to both ns1.yyy.com and ns2.yyy.com Can anyone give me some assistance here? This is a learning experience for me and days of documentation have left me very confused.

  Read the article

< Previous Page | 231 232 233 234 235 236 237 238 239 240 241 242  | Next Page >