Search Results

Search found 13458 results on 539 pages for 'maintenance management'.

Page 235/539 | < Previous Page | 231 232 233 234 235 236 237 238 239 240 241 242  | Next Page >

• Why is my HDD not showing up?

  - by Mike

  I'm on Windows 7, got a new 2 TiB NON-external hard disk. When I plug it in it doesn't show up on the Disk Management list in the Computer Management window (that you get by right-clicking My Computer and selecting "Manage"). At first I thought it was broken, but I could see it using a friend's computer. I've run a full disk scan using the official tool from Western Digital, no problems. I've formatted it and partitioned it at another friends place, I've even encrypted the disk fully without any problems, then mounted it and placed a text file on it with the word "hello" inside and saved the file. When I boot my own computer the disk shows up in BIOS. So the disk is not broken. I've tried changing what SATA slot on the motherboard I stick it in. Makes no difference. After all this: Why won't my Windows 7 discover the disk???

  Read the article

• Wake on Lan/Wan won't work after some time has passsed

  - by Vian Esterhuizen

  I have the following set up: Gigabyte Z77X-UD5H Wake On Lan Enabled Asus N66U Port Forwarding Static IP assigned to my computer Windows 7 Advanced Power Management - PCI Express - Off Intel 82579V - All options under Power Management checked I'm trying to set this up for Wake on Wan capabilities. If I shut down my computer and immediately try to Wake on Wan (and Lan) it works and starts up. While the computer is on, I've used a few WOL specific packet sniffers and the packet comes through on the correct port. After any period of time over a few minutes, waking on Wan or Lan won't work. The back "activity" light is blinking on my ethernet port on my computer, as well as on the router, so I would assume the network card is on and able to receive a signal. Any ideas? Suggestions? What can I do to troubleshoot the problem?

  Read the article

• USB to IDE/SATA adapter

  - by unknown (google)

  I have an old IDE HDD that I am trying to pull files off of. I am using a USD to IDE/SATA adapter. I plug in the power and adapter plugs into the drive and it fires up. I plug the USB plug into my XP laptop and it installs the drivers. I can see USB Mass Storage Device under Device Manager. My problem is I can't see the drive in either Windows Explorer or under Disk Management under Computer Management. Not sure what I am doing wrong. Do I have to slave the old hdd? Do I have to make BIOS changes?

  Read the article

• ZFS and SAN -- best practices?

  - by chris

  Most discussions of ZFS suggest that the hardware RAID be turned off and that ZFS should directly talk to the disks and manage the RAID on the host (instead of the RAID controller). This makes sense on a computer with 2-16 or even more local disks, but what about in an environment with a large SAN? For example, the enterprise I work for has what I would consider to be a modest sized SAN with 2 full racks of disks, which is something like 400 spindles. I've seen SAN shelves that are way more dense than ours, and SAN deployments way larger than ours. Do people expose 100 disks directly to big ZFS servers? 300 disks? 3000 disks? Do the SAN management tools facilitate automated management of this sort of thing?

  Read the article

• Can i create a website blacklist with Group Policy?

  - by jimmygee

  Like i can create "whitelist" functionality for blocking all sites and allowing some via the GP setting: "User Configuration Windows Settings Internet Explorer Maintenance Connection/Proxy Settings Exceptions - Do not use proxy server for addresses beginning with" Can i create also a blacklist option like this (or similar) in Group Policy?

  Read the article

• Rhythmbox - put a playlist on my iPod

  - by GorillaSandwich

  I have an old iPod nano and currently use iTunes in Windows to management. However, I'm trying to switch to Ubuntu. So far, iPod management is one major holdup. Besides being unable to easily manage podcasts, I also don't see a way to create a playlist and put it on my iPod. I can create a playlist on the computer in Rhythmbox, but I can't drag and drop it onto the iPod. I can create a playlist on the iPod itself, put I can't drag and drop songs from my library into it. If I right-click the songs, I can add them to playlists on the computer, but not on the iPod. How can I create a playlist of music in Rhythmbox and sync it to my iPod?

  Read the article

• When a python process is killed on OSX, why doesn't it kill the child processes?

  - by Hugh

  I found myself getting very confused a while back by some changes that I found when moving Python scripts from Linux over to OSX... On Linux, if a python script has called os.system(), and the calling process is killed, the called process will be killed at the same time. On OSX, however, if the main process is killed, anything that it launched is left behind. Is there something somewhere in OSX/Python where I can change this behaviour? This is causing problems on our render farm, where the processes can be killed from the management GUI, but the top level process is really just a wrapper, so, while the render farm management might think that the process has gone and the machine is freed up for another task, the actual processor-intensive task is still running, which can lead to huge blockages. I know that I could write more logic to catch the kill signal and pass it on to the child processes, but I was hoping that it might be something that could be enabled at a lower level.

  Read the article

• Windows 8 will not load color profiles - why?

  - by Fusilli Jerry

  I have a Spyder3Express color calibration device. Under Windows 7 the utility that came with it would happily load the custom profile I created with it without any hassles. Under Windows 8 (have just upgraded) there is no visible color shift when it says it has loaded the profile. I have gone into the Windows color management settings and when I select any profile and hit 'Set as Default' nothing happens. They all look the same. So Windows doesn't throw an error, but none of the profiles cause any color shifts at all. I have tried a large number of things, such as changing the global color settings for all user accounts and installing other color management software to see if it will load the profiles. The only way I can get a color shift is if I create a profile using Windows built in utility. Profiles created this way change the appearance of the screen, but any downloaded or created profiles make no difference. I am out of ideas. Please help :)

  Read the article

• Unable to delete all partitions on flash drive using Windows 7 OS??

  - by irrational John

  Recently I purchased an ADATA C802 8GB flash drive. Since the drive was new I decided to run some of the HD Tune Pro (v4.50) performance tests on it, mostly just for the heck of it. To avoid accidently destroying data HD Tune refuses to write to a drive unless there are no partitions on the drive. If you do attempt to write to a drive with partitions, it posts the message "Writing is disabled. To enable writing please remove all partitions." As you would expect, the ADATA came formatted with a single primary FAT32 partition in the Master Boot Record. But a number of unexpected things happened when I attempted to delete that partition. The first thing I tried was to use the Windows 7 (64-bit) Disk Management tool (diskmgmt.msc) to delete the partition. It would not let me. The context menu choice to delete that volume was not available. Next I opened up a command prompt window with Admin authority and ran diskpart. Diskpart deleted the volume for me. However, when I attempted to run an HD Tune write test on the drive I still got the "Writing is disabled" message. Huh??? So I fired up a utility I have which allows viewing drives at the sector level and verified that the partition table in the Master Boot Record was empty. No partitions. Yet HD Tune still thought there were partitions on the drive? So why was I still getting the "Writing is disabled" message from HD Tune Pro? And why wouldn't the Windows 7 Disk Management tool let me change the partitions on this drive. After doing the above, I plugged the ADATA into my MacBook. I was then able to format it as either a GPT or MBR partitioned drive with no problems. I am not looking for suggestions on how to format this drive. I can do that. What I do not understand and was hoping I might get insight into is why this drive behaves so strangely under Windows 7? And BTW, what's up with HD Tune Pro? BTW, if I plug the drive I formatted on my MacBook back into my Windows 7 64-bit system I still run into road blocks with the Disk Management tool. For example, I cannot delete all the GPT partitions on the ADATA so I can convert it into an MBR drive. I following Microsoft's instructions, the instructions just do not work with this ADATA flash drive. Anyone know what's up with this? It makes no sense to me. Has something changed in Windows 7 (Vista)??

  Read the article

• Installing Solaris with Window. Disk partitioning problem.

  - by RishiPatel

  I am running windows and want to install the solaris but having hard time while using installer. I have 1 primary partition of 40GB and one extended partition. Extended partition have 4 logical drive. Solaris disk management window show only two partition one is of 40GB(Primary) and second is Extended partition. Can i convert a logical drive into primary partition( I have one free of 25 GB). Please look at the screenshot of disk management utitlity of window. http://img195.imageshack.us/img195/2005/20726948.jpg Is there any way to install solaris without reformatting the and repartitioning whole drive? In case it is not possible how should i partition and using which utility ?

  Read the article

• Starting with administering a linux box

  - by Josh K

  I'm rather new to this, and I'd like to play with administering a linux box. Things I need to know how to do: Setup subdomains Setup FTP accounts Setup full domains / add domains MySQL setup / install / management LAMP setup / install / management This is probably going on a CentOS distro. I'd like links or a break down on how I can learn to do this. I am comfortable with a command line, but I'm trying to move from shared hosting to a VPS and would like to have some idea on how deep the water is before I do.

  Read the article

• SQL Server Installer Closes Silently Without Errors

  - by ashes999

  When I run the SQL Server 2008 R2 Express installer (32-bit or 64-bit), nothing happens. It will get to the screen where it asks me to accept the terms of license and send anonymous feedback; I check off both boxes and click Next, and it automatically starts installing the Support Files. And then the window disappears. I tried looking through the log files, but didn't see any errors. I've tried: x64 SQL Server R2 express x86 SQL Server R2 express X64 SQL Server R2 (full) X64 SQL Server Management Studio Of these, only management studio installed correctly; the two express editions failed silently, and the full version gave me different errors. I also tried running in Administrator mode (despite being logged in as an administrator user), but again, no difference.

  Read the article

• Problem with intel chipset 4 serie and centos dealing with dual head

  - by Antoine

  I've a fujitsu lifebook S7220, it's been a while since i try to configure it to use a dual head with centos 5.4 x86_64. Everytime I try, the xserver crash... I've got an intel chipset mobile 4 serie (GMA 4500MHD, if I recall good!) When I do an lspci -v i've got these : 00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) (prog-if 00 [VGA controller]) Subsystem: Fujitsu Limited. Unknown device 1451 Flags: bus master, fast devsel, latency 0, IRQ 177 Memory at f2000000 (64-bit, non-prefetchable) [size=4M] Memory at d0000000 (64-bit, prefetchable) [size=256M] I/O ports at 1800 [size=8] Capabilities: [90] Message Signalled Interrupts: 64bit- Queue=0/0 Enable- Capabilities: [d0] Power Management version 3 00:02.1 Display controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) Subsystem: Fujitsu Limited. Unknown device 1451 Flags: bus master, fast devsel, latency 0 Memory at f2400000 (64-bit, non-prefetchable) [size=1M] Capabilities: [d0] Power Management version 3 My question is, anyone already got this problem and how did you fix it? Thank you for your answer!

  Read the article

• data recovery from unallocated harddisk partition

  - by user36007

  Hi, I accidentally deleted a partition which mainly served as space I put my data, labeled D: drive. The partition wasn't subsequently formatted though, following the delete incident. Obviously the D: drive doesn't show up as it usually does when I run Windows 7. In the "Computer Management", on clicking the Disk Management I clearly see the space is now labled as unallocated. question: How do I go about recovering my data. Perhaps what the effective data recovery software I can use to resolve this issue. Thanks

  Read the article

• data recovery from unallocated harddisk partition

  - by user42151

  Hi I accidentally deleted a partition which mainly served as space I put my data, labeled D: drive. The partition wasn't subsequently formatted though, following the delete incident. Obviously the D: drive doesn't show up as it usually does when I run Windows 7. In the "Computer Management", on clicking the Disk Management I clearly see the space is now labled as unallocated. question: How do I go about recovering my data. Perhaps what the effective data recovery software I can use to resolve this issue. Thanks

  Read the article

• data recovery from unallocated harddisk partition

  - by user36007

  Hi, I accidentally deleted a partition which mainly served as space I put my data, labeled D: drive. The partition wasn't subsequently formatted though, following the delete incident. Obviously the D: drive doesn't show up as it usually does when I run Windows 7. In the "Computer Management", on clicking the Disk Management I clearly see the space is now labled as unallocated. question: How do I go about recovering my data. Perhaps what the effective data recovery software I can use to resolve this issue. Thanks

  Read the article

• How do I resolve the error "The file exists" when restoring a cube backup?

  - by Ant

  I'm trying to restore a cube backup (a .abf file) using SQL Server Management Studio, but I'm getting the error message: The following system error occurred: The file exists. . (Microsoft SQL Server 2005 Analysis Services) (yes, there really are two dots) Does anyone know how to resolve this so I can restore the backup? Here are the steps I'm using: Open Microsoft SQL Server Management Studio Make the connection to the AS server Right-click on the Databases node on the server tree view Choose Restore... Type in a new database name in Restore database Select the backup file in From backup file Enter the correct password Optionally tick Allow database overwrite (it happens both ways) Press OK -- get the above error message

  Read the article

• cannot add a user to sysadmin role in SQL Server

  - by George2

  Hello everyone, I am using SQL Server 2008 Management Studio. The current logon account belongs to machine local administrator group. I am using Windows Integrated Security mode in SQL Server 2008. My issue is, after log into SQL Server Management Studio, I select my login name under Security/Logins, then select Server Roles Tab, then select the last item -- sysadmin to make myself belong to this group/role, but it says I do not have enough permission. Any ideas what is wrong? I think local administrator should be able to do anything. :-) thanks in advance, George

  Read the article

• Biztalk 2009 install help

  - by _pemex99_

  Hi, I try to install Biztalk2009, with SQL 2008R2CTPNov, on Win Server 2008. I'm blocked at the configuration step "groups" : [19:22:18 Info Configuration Framework]Configuring feature: WMI [19:22:18 Info BtsCfg] Entering function: CBtsCfg::ConfigureFeature [19:22:18 Info BtsCfg] Configuring feature: WMI [19:22:18 Info BtsCfg] Entering function: CBtsCfg::IsSelectedAnswer [19:22:18 Info BtsCfg] Leaving function: CBtsCfg::IsSelectedAnswer [19:22:18 Info BtsCfg] Entering function: CWMI::Connect [19:22:18 Info BtsCfg] WMI is already connected [19:22:18 Info BtsCfg] Leaving function: CWMI::Connect [19:22:18 Info ConfigHelper] NT group BizTalk Server Operators was not created because it already exists [19:22:18 Info ConfigHelper NetAPI Info: ] Le groupe local spécifié existe déjà. [19:22:18 Info ConfigHelper] NT group BizTalk Server Administrators was not created because it already exists [19:22:18 Info ConfigHelper NetAPI Info: ] Le groupe local spécifié existe déjà. [19:22:18 Info BtsCfg] Entering function: CWMI::CreateGroup 2010-01-14 19:22:18:0527 [INFO] WMI CWMIInstProv::PutInstance() try to acquire lock 2010-01-14 19:22:18:0539 [INFO] WMI CWMIInstProv::PutInstance() lock acquired successfully 2010-01-14 19:22:18:0546 [INFO] WMI CWMIInstProv::VerifyMgmtDbCompatibility(CInstance) started 2010-01-14 19:22:18:0553 [INFO] WMI CWMIInstProv::VerifyMgmtDbCompatibility(CInstance) finished successfully 2010-01-14 19:22:18:0564 [INFO] WMI CWMIInstProv::PutInstance(MSBTS_GroupSetting.MgmtDbName="BizTalkMgmtDb",MgmtDbServerName="ECTXEVLBZTK") started 2010-01-14 19:22:18:0572 [INFO] WMI CAdapter::ConvertWMI2Admin() started 2010-01-14 19:22:18:0581 [INFO] WMI CDataContainer::SetWCHAR() - Possible problem: item value is overwritten 2010-01-14 19:22:18:0591 [INFO] WMI CAdapter::ConvertWMI2Admin() finished with HR=0 2010-01-14 19:22:18:0611 [INFO] WMI QueryStringValue query regkey 'MgmtDBServer' 2010-01-14 19:22:18:0620 [INFO] WMI CAdmCoreGroupInst::TryCreateNewGroup() started 2010-01-14 19:22:18:0632 [INFO] WMI Creating Mgmt database... 2010-01-14 19:22:18:0641 [INFO] WMI Calling CDataSource.Open() against ECTXEVLBZTK\master 2010-01-14 19:22:18:0792 [INFO] WMI CDataSource.Open() returned 2010-01-14 19:22:18:0810 [WARN] AdminLib GetBTSMessage: hrErr=80040e1d; Msg=Error "0x80040E1D" occurred.; 2010-01-14 19:22:18:0824 [WARN] AdminLib GetBTSMessage: hrErr=c0c02524; Msg=Failed to create Management database "BizTalkMgmtDb" on server "ECTXEVLBZTK". Error "0x80040E1D" occurred.; 2010-01-14 19:22:18:0835 [ERR] WMI Failed in pAdmInst->Create() in CWMIInstProv::PutInstance(). HR=c0c02524 2010-01-14 19:22:18:0846 [ERR] WMI WMI error description is generated: Failed to create Management database "BizTalkMgmtDb" on server "ECTXEVLBZTK". Error "0x80040E1D" occurred. 2010-01-14 19:22:18:0860 [INFO] WMI CWMIInstProv::PutInstance() finished. HR=c0c02524 [19:22:18 Error BtsCfg] f:\bt\890\private\source\setup\prod\btssetup\btscfg\btswmi.cpp(358): FAILED hr = c0c02524 [19:22:18 Error BtsCfg] Failed to create Management database "BizTalkMgmtDb" on server "ECTXEVLBZTK". Error "0x80040E1D" occurred. It seems that the install can't create Managment database, But the SSO database is created OK... Has someone a clue ?

  Read the article

• Windows 7 Bootcamp to see data doubler SATA SSD in Optical Bay Connector

  - by bumble_bee_tuna

  Hi I purchased a OWC data doubler http://eshop.macsales.com/item/OWC/DDAMBS0GB/ ... Long story short it lets you add a second HD to your macbook pro in place of the cd/dvd drive (which is useless anyway, impossible to get stuff out when stuck). My current setup is 600gb intel SSD bootdrive 100gb partition for OSX / 500gb for Windows 7 Prof from Bootcamp (use 99 % of time). My desire is to have a second 300gb SSD to run disk intensive VM's off of. So I added a second 300gb intel SSD (again, NO desire to boot off of) on the sata optical port. I can see the drive no problem if I boot in to OSX, however, can't see it in disk management on Win7 ??? Any ideas similar experience ... Funny thing is I can see it in "Device Manager Disk Drivers" but not Disk Management ??? Also no I don't want to use Fusion/Parallels this is a waste of resources for me.

  Read the article

• Is there anything wrong with disabling Teredo?

  - by Wayne Hartman

  Today while doing some routine maintenance I discovered that my internet-connected network adapter was using a 6to4 tunnel to connect to my ISP. Some self-eduction on Teredo seemed to indicate quite a few potential security vulnerabilities with using the protocol. I have disabled my network adapter from using Teredo and it doesn't seem to impact my gateway in any way. Is there anything I am missing that should encourage me to turn it back on?

  Read the article

• Dell Powervault MD3000 - Not sharing Files between servers

  - by Kevin

  I'm a developer who has to set up a Dell Powervault MD3000 due to lack of resources. I have connected the Powervault to 2 Dell 2950 servers via the SAS cables. I performed the setup using Dell's MD Storage Manager software (4 disks, RAID 5 with hot spare). Then I added the disks using Windows 2003 disk management (Basic, not dynamic disk and formatted with NTFS). When I add files to the array from one server, they are not visible on the other server (and vice-versa). Is the error in the windows disk management configuration?

  Read the article

• How can I create a copy of a vm in vSphere Client running on ESXi 4.0?

  - by user37860

  I'd like to create copies of the VMs located on my datastore that I can put up temporarily on a different server while I perform some maintenance on our main virtualization server. Aside from using the Converter utility (which I don't believe I can use with the Linux machines) is there a way to make copies of these machines? It would make my life a lot easier. Thanks!

  Read the article

• How can I return a 503 status in apache without invoking external scripts

  - by dan mackinlay

  I need to return a 503 status code from one of my sites while it's down for maintenance, in the time-honoured SE_firendly fashion. I can't seem to work out how to do this without invoking external scripts, which I'd rather avoid. Is there an apache directive which will allow me to return an arbitrary HTTP status code without resorting to hacks like invoking a php script which sets the status header?

  Read the article

• SQL 2008 managing 2 Instances on single Physical server

  - by Rajeev

  Hi, I need some calrification about managing SQL server 2008. The scenario is as follows: I have One Windows Physical server at Primary site, I want to have Two different applications database on it, so shall I create two Instances on same server or shall have diffenrent server for another database. First Database is for management purpose while second would be used for Reporting purpose. There is a second database at the secondary site, which will be in Passive mode and I intend to connect them through MSCS. Now, can I have both Instances on Single server and both will work fine? The management database will be used more. Please reply soon. Can both Instances have dedicated reources allocated to them?

  Read the article

< Previous Page | 231 232 233 234 235 236 237 238 239 240 241 242  | Next Page >