Search Results

Search found 6942 results on 278 pages for 'enabled'.

Page 236/278 | < Previous Page | 232 233 234 235 236 237 238 239 240 241 242 243  | Next Page >

• No Internet connectivity to linux container on Debian

  - by kirankumar

  I have created a linux container with debian-wheezy template. I am not able to have internet connectivity from the container. Below is my network configuration. Could some one please help me in figuring out the issue ? I can ping to the eth0 ip address in the container from the host. Similarly, i can ping from container to br0 ip address on the host. /etc/network/interfaces on host =============================== # The loopback network interface auto lo iface lo inet loopback # The primary network interface #allow-hotplug eth0 auto eth0 iface eth0 inet dhcp # bridge configuration auto br0 iface br0 inet dhcp bridge_ports eth0 vethCE2 bridge_fd 0 bridge_stp off bridge_maxwait 0 ifconfig -a output on host ========================== ifconfig -a br0 Link encap:Ethernet HWaddr 08:00:27:bd:61:5e inet addr:10.0.0.11 Bcast:10.0.0.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:febd:615e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:422 errors:0 dropped:0 overruns:0 frame:0 TX packets:266 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:174110 (170.0 KiB) TX bytes:31582 (30.8 KiB) eth0 Link encap:Ethernet HWaddr 08:00:27:bd:61:5e UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:13017 errors:0 dropped:0 overruns:0 frame:0 TX packets:6210 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:7944745 (7.5 MiB) TX bytes:1368421 (1.3 MiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:835 errors:0 dropped:0 overruns:0 frame:0 TX packets:835 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:91148 (89.0 KiB) TX bytes:91148 (89.0 KiB) vethCE2 Link encap:Ethernet HWaddr fe:3a:43:52:14:49 inet6 addr: fe80::fc3a:43ff:fe52:1449/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:52 errors:0 dropped:0 overruns:0 frame:0 TX packets:205 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2660 (2.5 KiB) TX bytes:31133 (30.4 KiB) brctl show output on host ========================== bridge name bridge id STP enabled interfaces br0 8000.080027bd615e no eth0 vethCE2 /etc/network/interfaces on container ======================================= auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 10.0.0.99 netmask 255.255.255.0 network 10.0.0.0 ifconfig -a output on container =============================== root@CE2:~# ifconfig -a eth0 Link encap:Ethernet HWaddr 00:11:22:33:44:00 inet addr:10.0.0.99 Bcast:10.0.0.255 Mask:255.255.255.0 inet6 addr: fe80::211:22ff:fe33:4400/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:198 errors:0 dropped:0 overruns:0 frame:0 TX packets:52 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:30121 (29.4 KiB) TX bytes:2660 (2.5 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:26 errors:0 dropped:0 overruns:0 frame:0 TX packets:26 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2366 (2.3 KiB) TX bytes:2366 (2.3 KiB) Networking content of /var/lib/lxc/CE2/config ============================================== # networking lxc.network.type = veth lxc.network.flags = up lxc.network.link = br0 lxc.network.name = eth0 lxc.network.veth.pair = vethCE2 # It is fine to be commented out #lxc.network.ipv4 = 192.168.10.21/24 # Change this lxc.network.hwaddr = 00:11:22:33:44:00 Let me know if you need any other details. Thanks, Kiran Kumar

  Read the article

• How can Windows XP/7 users cleanly connect to Mac OS X Server 10.9.4 Mavericks with Active Directory integration?

  - by JakeGould

  I’m a Linux/Unix systems admin who also manages a Macintosh server infrastructure & there is a lone Mac Mini in the mix running 10.9.4 that I would like Windows XP & Windows 7 users to connect to with little or no hassle. The problem? Windows users can’t seem to even get to the point of a password prompt yet connect. Mind you this server replaced a Mac OS X 10.6.8 server that had issues, but never had issues with Windows users connected. The gist of this post is: The tons of different messages out there about Mac OS X 10.9.4 Samba support are mind-numbingly confusing. Can anyone share some solid specifics here? I’ve read pieces like this one here that suggest turning off file sharing & then adding a share with AFP/SMB enabled would work. But the suggestion seems to apply to 10.8. And from what I know a lot has changed in Samba support in 10.9 let alone the iterations to 10.9.4. Then I found this great tutorial here that explains things step-by-step. Which seems like it should work, but the problem is the example given applies to a local user created on the Mac when I would like users in an Active Directory group—which the Mac is bound to—access the Mac Mini shares. There are also tons of great tips here on MacWindows.com but nothing seems solid to the issue I am facing. So from what I am reading these are my options: Local User Versus Active Directory: Setup a common local user on the Mac OS X 10.9.4 server to be used for Samba sharing since Active Directory won’t work. Is this really the case? Because loss of AD integration is a major pain. Do Extended File Attributes Get Retained from Windows Users: If this were to work, how do extended attributes come into play? Loss of metadata & related info is not an option. How Fragile is Any of this to Updates: How does any of this shake out with Mac OS X updates as well as Windows updates? Installing Official, Open Source Samba: Would upgrading the Samba install on the server to the official open source Samba via a package like SMBUp or via the Hombrew method described here help or make the issue worse? I fully understand there have historically been issues in mixed environments, but nowadays Windows users connecting to a Mac seem to have a truly hellish road ahead of them. Unless I am missing something?

  Read the article

• Configuring Windows 2003 As A Router

  - by Sean M

  I am trying to configure a Windows 2003 server to act as a router, so that the two subnetworks that I'm dealing with can communicate with one another without NAT. I am mostly sure that I have configured Windows 2003 incorrectly, and I'm finding it very difficult to drill down through Google results to something helpful. I have a 192.168.1.0/24 network that is my "production" network (in the sense that I'm in trouble if I screw it up) and a 10.0.0.0/8 network that is my test network. The 192.168.1.0 network is ruled by a gateway whose routing table looks like this (my address redacted): The Windows 2003 server, "prime," is multihomed. Its network adapters are at 192.168.1.122, (as seen above), 10.0.0.1, and 10.0.0.2. I added the Routing and Remote Access role to it, and enabled LAN routing. I do not have it using RIP or other routing protocols. Its current routing table is shown below. To me, it looks like all of the right routes are there for traffic to pass between the 192.168.1.0 network and the 10.0.0.0 network. However, traffic does not pass. The 10.0.0.11 and .12 clients cannot be contacted from the 192.168.1.0 network. When I use traceroute to try to get to them, the trace gets to the Windows 2003 server's 192.168.1.122 address, then produces nothing but "* * *" timeouts. When I try to traceroute to 192.168.1.1 from a 10.0.0.0-network client, I get "destination host unreachable." However, I know that the routing is working at least a little, because from the 192.168.1.0 network, I can connect to the Windows server just fine by referring to it as 10.0.0.1. What static routes would allow me to contact 10.0.0.11 and .12 from the 192.168.1.0 network? Is it possible to tell the Windows server "since you are a DHCP/DNS server, you already know routes to get to machines that are getting IP addresses from you, please add those to your routing table" ? Will using RIP or OSPF on the Windows server actually be helpful in this situation?

  Read the article

• Apache + PHP in paths with accented letters

  - by Álvaro G. Vicario

  I'm not able to run a PHP enabled web site under Apache on Windows XP if the path to DOCUMENT_ROOT contains accented letters. I'm not referring to the script file names themselves but to any folder in the path components. I have this virtual host definition: <VirtualHost *:80> ServerName foo.local DocumentRoot "E:/gonzález/sites/foo" ErrorLog logs/foo.local-error.log CustomLog logs/foo.local-access.log combined <Directory "E:/gonzález/sites/foo"> AllowOverride All Options Indexes FollowSymLinks Order allow,deny Allow from all </Directory> </VirtualHost> If I save the file in ANSI I get a syntax error: DocumentRoot must be a directory If I save the file in Unicode I get another syntax error: Invalid command '\xff\xfe#', perhaps misspelled or defined by a module not included in the server configuration (looks like it's complaining about the BOM) If I save the file in BOM-less UTF-8 Apache works fine and it serves static files with no apparent issue... ... however, PHP complaints when loading any *.php file (even an empty one): Warning: Unknown: failed to open stream: No such file or directory in Unknown on line 0 Fatal error: Unknown: Failed opening required 'E:/gonzález/sites/foo/vacio.php' (include_path='.;C:\Archivos de programa\PHP\pear') in Unknown on line 0 I decided to try the 8+3 short name of the directory (just a test, I don't want to use such a workaround): <VirtualHost *:80> ServerName foo.local DocumentRoot "E:/GONZLE~1/sites/foo" ErrorLog logs/foo.local-error.log CustomLog logs/foo.local-access.log combined <Directory "E:/GONZLE~1/sites/foo"> AllowOverride All Options Indexes FollowSymLinks Order allow,deny Allow from all </Directory> </VirtualHost> But I get the same behaviour: Warning: Unknown: failed to open stream: No such file or directory in Unknown on line 0 Fatal error: Unknown: Failed opening required 'E:/gonzález/sites/foo/vacio.php' (include_path='.;C:\Archivos de programa\PHP\pear') in Unknown on line 0 While there're obvious workarounds (use plain ASCII in all directory names or create NTFS junctions to hide actual names) I can't believe that this cannot be done. Do you have more information about the subject? My specs include 32 bit Windows XP Professional SP3, Apache/2.2.13 and PHP/5.2.11 running as Apache module (but I've noticed the same issue in another box with Windows Vista and PHP/5.3.1).

  Read the article

• Gigabyte GA-970A-UD3 mobo won't boot from USB flash drive

  - by user38586

  I am trying to boot BAMT a Debian flavor via USB on a brand new Gigabyte GA-970A-UD3 motherboard. I tried various flash drive and various OS. I never had this problem with ASUS and MSI. The problem is from Gigabyte hardware. I found that my BIOS is very strict about MBR compatibility. Now I can boot in DOS mode. The flash drive need to be formated as a Win98 Startup disk using HP USB disk storage format tool. Unetbootin menu is booting from USB but won't install BAMT. If I use Windows or Linux diskimager the working MBR is deleted. I tried converting BAMT .img to .iso and it is not booting with Unetbootin. Is it possible to boot BAMT(Debian Linux) from a Win98 DOS command prompt? Maybe there is a way to burn the image and keep the working MBR? If the working MBR is deleted, the flash drive is not recognized at all by the BIOS. This is the info I found that got me booting for the first time in DOS: GB's BIOS will only boot USBs formatted to FAT-32, conforming to normal MBR bootloader. I've seen this before, and surmised that the 'stick-maker' was formatting in ReiserFile, or one of the EXT 'flavors', but no one ever followed up to confirm or deny... Also, if it's putting the bootloader into its own partition - won't work! In the BIOS, on the "Integrated Peripherals" page, the "USB Storage Function" item must be enabled (which should be the default) to allow USB booting... I've put a little work into a 'GB USB booting tutorial', and frankly, I'd just go ahead and finish it up for you, but I really don't want to reboot the several times it will take me to 'firm up' procedural details, and take the BIOS/boot pictures for the post - just noticed VAIL finally went 'public beta', so will be downloading for likely twenty-six hours or so There's likely enough there to test a 'raw DOS boot', just to see if your hardware (especially the USB stick itself) will do it... Some post later: Fixed. Here is a brief summary. Since my ubuntu live usb sticks (2gb kingston and 8gb sandisk sd/usb reader - fat32, created in ubuntu 10.04) would not boot this board even though they would boot my ga-ep45-ud3p, I decided to try bilbat's suggestion with the HP usb boot program. I created the win98 boot disk on the kingston 2gb stick without reformatting. It booted right up. Next, I used windows version of unetbootin to write the ubuntu live cd to the kingston disk. This fired right up and completed the install. Everything seems to be in good order now. Unfortunately I can boot in DOS mode but can't boot BAMT.

  Read the article

• AWS EC2 instance not pingable or available in browser

  - by Slimmons

  I've seen this questions asked other places, but now I've run through every fix proposed in other questions so I'm re asking it here, in hopes that someone will have a different solution. Problem: I have a EC2 instance, and I can ssh into it and work on it, and I have a Elastic ip set to it. I am unable to ping this machine, or log in to it using my browser. Solutions mentioned and tried: service httpd start i. response I get is "unrecognized service" ii. when I run apache2ctl -k start, it shows "httpd already running", so I'm assuming httpd is not the problem, it's just possibly named something else because of apache2, or for whatever reason. I went into EC2-Security Group- Default (which is the one I used.)-inbound, and everything there is set up correctly (I'm assuming). There it shows 80(HTTP) 0.0.0.0/0. 443(HTTPS) 0.0.0.0/0, and various other servies with their ports and 0.0.0.0/0 next to them. I also enabled a rule for enabling ICMP Request All on 0.0.0.0/0 temporarily for testing purposes I've tried disabling the iptables with "service ufw stop" Just in case I'm doing something really stupid, because I'm not all that used to connecting to web servers that I've spun up, I'm typing in the address to the machine into the url like this (assuming my ip address was ip.address). i. http:/(slash)ip.address/ ii. ip.address iii. https:/(slash)ip.address/ iv. ip.address/webFolderName/ v. http:/(slash)ip.address/webFolderName/ None of the attempts worked, and the only thing I haven't tried that i've seen is to start wireshark on the machine, and see if the requests are reaching it, and it's just ignoring them. I'm not sure I want to do that yet, since A). I'm not 100% positive how to use wireshark without the gui, since it's the only way I've ever used it (I really should get used to it in terminal, but I didn't even know you could). B). It really seems like I'm missing something simple in getting this to work. Thanks in advance for any help.

  Read the article

• Resolving CloudFlare DNS related mail delivery problems

  - by Andy Castles

  I recently started using CloudFlare and am having a few teething problems. Our domain is netlanguages.com and while we have a lot of sub-domains listen, we are currently only trialling a few of the servers through the CloudFlare CDN (for example, www.netlanguages.com is enabled for CDN, netlanguages.com is not). The actual CDN service seems to be reliable, but the problem that we are having is with DNS, and specifically with mail delivery. The background is that we have contact forms on our web site which use PHP mail() to send the details to end-users' email addresses, with the "from" address of the messages being [email protected] which is a valid address on our mail server. Most of the mails are arriving correctly, but a few specific people are not receiving them. The webserver uses qmail to deliver the messages, and the qmail log files show us some of the errors that the receiving mail servers return when they reject the mail delivery attempt. Two examples: Connected to 94.100.176.20 but sender was rejected./Remote host said: 421 DNS problem (interdominios.netlanguages.com). Try again later Connected to 213.186.33.29 but sender was rejected./Remote host said: 451 DNS temporary failure (#4.3.0) From what I can tell, the receiving SMTP server is doing a DNS lookup of some description on either the host of the "from" email address (netlanguages.com) or the server name given in the EHLO command of the SMTP conversation (in the first example above, interdominios.netlanguages.com), both of which should resolve to non-CloudFlare IP addresses. I've read that the CloudFlare DNS service is very reliable and fast but both of the problems above seem to point to a problem with remote servers unable to do DNS lookups. I should also point out that we changed our DNS to CloudFlare on 6th Feb, and since then started experiencing these mail delivery problems. On 22nd Feb we moved our DNS away from CloudFlare to see if the issues were related to CloudFlare and after a few hours delivery began to work. Then on 26th Feb I moved the DNS back to CloudFlare again and delivery problems started again. The issues definitely seems to be related to DNS, but I don't know if it's a configuration issue, or something else. Finally, I should say that our two DNS MX records point to non-CDN A record IP addresses, interdominios.netlanguages.com (the web and qmail server) also points to a non-CDN A record IP address. Does anyone know what the problem could be here? Any light you can shed on this will be most appreciated. Many thanks, Andy

  Read the article

• Installing Phusion Passenger 4.0.20 on Ubuntu 13.10

  - by tempestfire2002

  So I'm trying to install Passenger on the newest version of KUbuntu (13.10). I installed Apache2 using the apache2-mpm-worker package using the Muon Package Manager. And these are the commands I ran. rvmsudo gem install passenger rvmsudo passenger-install-apache2-module But I keep getting the following errors: [Fri Oct 18 15:52:13.227790 2013] [core:warn] [pid 13095] AH00111: Config variable ${APACHE_LOCK_DIR} is not defined [Fri Oct 18 15:52:13.227933 2013] [core:warn] [pid 13095] AH00111: Config variable ${APACHE_PID_FILE} is not defined [Fri Oct 18 15:52:13.227969 2013] [core:warn] [pid 13095] AH00111: Config variable ${APACHE_RUN_USER} is not defined [Fri Oct 18 15:52:13.227991 2013] [core:warn] [pid 13095] AH00111: Config variable ${APACHE_RUN_GROUP} is not defined [Fri Oct 18 15:52:13.228026 2013] [core:warn] [pid 13095] AH00111: Config variable ${APACHE_LOG_DIR} is not defined [Fri Oct 18 15:52:13.231737 2013] [core:warn] [pid 13095:tid 3074562624] AH00111: Config variable ${APACHE_RUN_DIR} is not defined [Fri Oct 18 15:52:13.232760 2013] [core:warn] [pid 13095:tid 3074562624] AH00111: Config variable ${APACHE_LOG_DIR} is not defined [Fri Oct 18 15:52:13.233043 2013] [core:warn] [pid 13095:tid 3074562624] AH00111: Config variable ${APACHE_LOG_DIR} is not defined [Fri Oct 18 15:52:13.233078 2013] [core:warn] [pid 13095:tid 3074562624] AH00111: Config variable ${APACHE_LOG_DIR} is not defined AH00526: Syntax error on line 74 of /etc/apache2/apache2.conf: Invalid Mutex directory in argument file:${APACHE_LOCK_DIR} -------------------------------------------- WARNING: Apache doesn't seem to be compiled with the 'prefork', 'worker' or 'event' MPM Phusion Passenger has only been tested on Apache with the 'prefork', the 'worker' and the 'event' MPM. Your Apache installation is compiled with the '' MPM. We recommend you to abort this installer and to recompile Apache with either the 'prefork', the 'worker' or the 'event' MPM. Press Ctrl-C to abort this installer (recommended). Press Enter if you want to continue with installation anyway. The result of my running apache2ctl -V is: Server version: Apache/2.4.6 (Ubuntu) Server built: Aug 9 2013 14:31:04 Server's Module Magic Number: 20120211:23 Server loaded: APR 1.4.8, APR-UTIL 1.5.2 Compiled using: APR 1.4.8, APR-UTIL 1.5.2 Architecture: 32-bit Server MPM: worker threaded: yes (fixed thread count) forked: yes (variable process count) Server compiled with.... -D APR_HAS_SENDFILE -D APR_HAS_MMAP -D APR_HAVE_IPV6 (IPv4-mapped addresses enabled) -D APR_USE_SYSVSEM_SERIALIZE -D APR_USE_PTHREAD_SERIALIZE -D SINGLE_LISTEN_UNSERIALIZED_ACCEPT -D APR_HAS_OTHER_CHILD -D AP_HAVE_RELIABLE_PIPED_LOGS -D DYNAMIC_MODULE_LIMIT=256 -D HTTPD_ROOT="/etc/apache2" -D SUEXEC_BIN="/usr/lib/apache2/suexec" -D DEFAULT_PIDLOG="/var/run/apache2.pid" -D DEFAULT_SCOREBOARD="logs/apache_runtime_status" -D DEFAULT_ERRORLOG="logs/error_log" -D AP_TYPES_CONFIG_FILE="mime.types" -D SERVER_CONFIG_FILE="apache2.conf" As can be seen, the server is compiled with the worker MPM, so why is passenger complaining? And how do I solve the above errors (warnings, really, but to be safe, I'd like to not have any warnings)? Thanks.

  Read the article

• Debugging IO limitation

  - by Martin F

  I have a Fedora box with some severe IO limitations which I have no idea how to debug. The server has a Areca Technology Corp. ARC-1130 12-Port PCI-X to SATA RAID Controller with 12 7200 RPM 1.5 TB disks and a Marvell Technology Group Ltd. 88E8050 PCI-E ASF Gigabit Ethernet Controller. uname -a output: 2.6.32.11-99.fc12.x86_64 #1 SMP Mon Apr 5 19:59:38 UTC 2010 x86_64 x86_64 x86_64 GNU/Linux The server is a file server running Nginx with the stub status module enabled, so I can see the current amount of connections. The problem present itself when I have a high number of simultaneous connections in a writing state. Usually around 350, at this very moment it's at 590 and the server is almost unusable and stuck at 230mbit/s. If I run stop and hit 1 to see CPU core usages I have all 4 cores with around 99% io wait, if I run iotop the nginx workers are the only processes producing any read load, currently at around 25MB/s. I have each of the workers bound to their own core. Initially I figured it was just the disks being bugged. But I've run fscheck and smartmontools checks and found no errors. I also ran an iozone test which you can see the result of here: http://www.pastie.org/951667.txt?key=fimcvljulnuqy2dcdxa Additionally, when the amount of connections are low I have no problem getting a good speed. If I wget over the local network it easily hits 60MB/sec. Right now I just tried putting a file in /dev/shm, then I symlinked a file from the public dir to it and used wget over the local network and only got 50KB/s. Also, if I try to cp /dev/shm/test /root/test it quickly copies around 740MB and then slows down HEAVILY. Again with iotop reporting 99% iowait. I'm not really sure how to go about figuring out what the problems are. It could be a natural disk limitation but then the file from /dev/shm ought to transfer so it seems there's a network limit, but that's fine when there's not many connections. Perhaps it's a TCP stack problem but I really have no idea how to check that. Any suggestions on how to proceed with debugging would be very welcome. If additional information is required then let me know and I'll try to get it. Thanks.

  Read the article

• Link aggregation with freebsd8 and a cicso 3550, what am i doing wrong?

  - by Flamewires

  Hey, I am trying to setup Link Aggrigation with LACP (well, anything that provides increased bandwidth and failover using my setup will work). I'm running FreeBSD 8.0 on 3 machines. M1 is running 2 10/100 ethernetcards setup for link aggrigation using lagg. for reference: ifconfig em0 up ifconfig tx0 up ifconfig create lagg0 ifconfig lagg0 laggproto lacp laggport tx0 laggport em0 192.168.1.16 netmask 255.255.255.0 I plugged them into ports 1 and 2 of a Cicso 3550. then ran: configure terminal interface range Fa0/1 - 2 switchport mode access switchport access vlan 1 channel-group 1 mode active (everythings in vlan 1) Now Im able to connect the other computers to other ports on the switch and failover works great, i can unplug cables in the middle of a transfer and the traffic gets rerouted. However, im not noticing any speed increase. My test setup: load balancing: i tried dst and src on the switch, neither seemed to give me a speed increase. I am SCPing 2 500 meg files from the lagg computer to other computers (one each) which are also running 10/100 full duplex cards. I get transfer speeds of about 11.2-11.4 Mbps to a single host, and about half that (5.9-6.2) Mbps when transferring to both at the same time. From what I understood with destination load balancing the router was suppose to balance traffic headed for 1 computer over 1 port and traffic headed for another over a diff(in this case) the other port. With destination-MAC address forwarding, when packets are forwarded to an EtherChannel, the packets are distributed across the ports in the channel based on the destination host MAC address of the incoming packet. Therefore, packets to the same destination are forwarded over the same port, and packets to a different destination are sent on a different port in the channel. For the 3550 series switch, when source-MAC address forwarding is used, load distribution based on the source and destination IP address is also enabled for routed IP traffic. All routed IP traffic chooses a port based on the source and destination IP address. Packets between two IP hosts always use the same port in the channel, and traffic between any other pair of hosts can use a different port in the channel. (Link) What am i doing wrong/what would i need to do to see a speed increase beyond what i could do with just a single card?

  Read the article

• StrongSwan + xl2tpd client timeout between 2-5 minutes

  - by Howard Guo

  I run CentOS 6.4 on Amazon EC2, using xl2tpd-1.3.1 from EPEL repository together with StrongSwan 5.0.4. I setup a simple IPSec connection: conn l2tp type=transport keyexchange=ikev1 rekey=no authby=psk leftsubnet=0.0.0.0/0 rightsubnet=0.0.0.0/0 compress=yes auto=add And here is xl2tpd.conf: [global] ipsec saref = yes [lns default] ip range = 192.168.0.2-192.168.0.250 local ip = 192.168.0.1 ppp debug = yes pppoptfile = /etc/ppp/options.xl2tpd length bit = yes Here is options.xl2tpd: ms-dns 8.8.4.4 auth lock debug proxyarp There is only one client - Android 4.2 Android connects successfully: Oct 27 19:45:02 ip-172-31-17-30 xl2tpd[2706]: Connection established to x.x.x.x, 59578. Local: 18934, Remote: 29291 (ref=0/0). LNS session is 'default' Oct 27 19:45:02 ip-172-31-17-30 xl2tpd[2706]: Call established with x.x.x.x, Local: 36452, Remote: 29845, Serial: -1369754322 Oct 27 19:45:02 ip-172-31-17-30 pppd[2709]: pppd 2.4.5 started by howard, uid 0 Oct 27 19:45:02 ip-172-31-17-30 pppd[2709]: Using interface ppp0 Oct 27 19:45:02 ip-172-31-17-30 pppd[2709]: Connect: ppp0 <--> /dev/pts/0 Oct 27 19:45:02 ip-172-31-17-30 pppd[2709]: peer from calling number x.x.x.x authorized Oct 27 19:45:02 ip-172-31-17-30 pppd[2709]: Deflate (15) compression enabled Oct 27 19:45:03 ip-172-31-17-30 pppd[2709]: Cannot determine ethernet address for proxy ARP Oct 27 19:45:03 ip-172-31-17-30 pppd[2709]: local IP address 192.168.0.1 Oct 27 19:45:03 ip-172-31-17-30 pppd[2709]: remote IP address 192.168.0.2 Oct 27 19:45:03 ip-172-31-17-30 charon: 06[KNL] 192.168.0.1 appeared on ppp0 Oct 27 19:45:03 ip-172-31-17-30 charon: 06[KNL] 192.168.0.1 disappeared from ppp0 Oct 27 19:45:03 ip-172-31-17-30 charon: 06[KNL] 192.168.0.1 appeared on ppp0 Oct 27 19:45:03 ip-172-31-17-30 charon: 06[KNL] interface ppp0 activated In the meanwhile, Internet works perfectly on the Android client, the VPN connection is stable and fast. However, it always happens that within 2-5 minutes after the connection is established: Oct 27 19:47:07 ip-172-31-17-30 xl2tpd[2706]: Maximum retries exceeded for tunnel 18934. Closing. Oct 27 19:47:07 ip-172-31-17-30 xl2tpd[2706]: Connection 29291 closed to 95.91.227.224, port 59578 (Timeout) Oct 27 19:47:07 ip-172-31-17-30 charon: 06[KNL] interface ppp0 deactivated Oct 27 19:47:07 ip-172-31-17-30 charon: 06[KNL] interface ppp0 deleted Then the VPN connection is broken. So what might have gone wrong? The same L2TP service works flawlessly on iOS 7, MacOS 10.8, and Windows 7, there is no disconnection issue on those OSes. Thank you!

  Read the article

• Vagrant - Failed login, ssh not set up

  - by motleydev

  This question is two fold because somewhere in my attempts to solve the problem, I created a new one. First: I was trying to vagrant up using a Vagranfile based on the standard hashicorp/precise32 box. Everything worked up until default: SSH auth method: private key where it would eventually time out. Enabling gui in the Vagrantfile showed that the machine never actually logs in. I can use the standard user/pass and log in from that point but the vagrant up process still remains at that prior status. Here's where my understanding might be a little dim. I've tried setting auth method from the insecure_pass_key to my root ~/.ssh/id_rsa or whichever one I wanted to use. I'm not entirely sure where to put a copy of the public key or my authorized keys file. I've got a .vagrant.d folder in my user dir (I'm on OSX) which seems to contain the box images. I've got a .vagrant folder in my directory with the Vagrantfile which seems to contain the specific machine I am building off of. I've tried pouring over the docs and forums but I seem to be missing a key concept here. And Now: After a host of tips/tricks such as rolling back by VirtualBox install, uninstalling/reinstalling Vagrant and VritualBox several times, when I try to run vagrant ssh-config with a Vagrantfile based on the same hashicorp/precise32 it says that the box is not enabled for SSH. Specifically, this error: The provider for this Vagrant-managed machine is reporting that it is not yet ready for SSH. Depending on your provider this can carry different meanings. Make sure your machine is created and running and try again. Additionally, check the output of `vagrant status` to verify that the machine is in the state that you expect. If you continue to get this error message, please view the documentation for the provider you're using. So now I am slightly up a creek. Any help would be appreciated if not just clarifying a concept. Some pertinent info: I'm on OSX Maverics Due to the fact I'm running a dual HD system with system files on one HD and user files on another, my permissions are a little wonky and VBoxManage will only let me run commands via Sudo - not sure if it's pertinent - but maybe. I have no idea what I'm doing. That part is perhaps more important.

  Read the article

• Intermittent Disconnection of Client Computers from Domain Server

  - by dilip nagle

  The Background: I have Windows 2008 server Enterprise Version with 25 user cal licences. It has a domain and all users and a network shared HP printer in it. The Server has two network cards and both these cards as well as all client machines are on IP addressing scheme of 192.168.1.* with subnetmask 255.255.255.0. Of the two network cards viz. 192.168.1.231 and 192.168.1.233, only 192.168.1.231 is registered with DNS. In 192.168.1.233(i.e. 2nd network card) has default getway as 192.168.1.231 and dns address as 192.168.1.231. The Server has three hard disks with capacities as 500gb, 500gb and 1TB and are partitioned as (C,D,E), (F,G) and (K) with partition K having all user data into various Shared Folders. Each of these folders(On Partition K), are mapped onto each user's computer as per the right of access given to them. The Problem: The Server was installed about 6 months ago and till date not even once, the Server has Hung or has given any problem. All the Clients computers are able to run the web based software from their computers via ip address, e.g. http://192.168.1.231/webERP/default.aspx. However, occassionally, when any client computer tries to browse network mappings, it hangs. Again, there is no fixed pattern. This may happen after running smoothly for say 3 days. On each Client's machine, the network settings are as follows: IP Address: 192.168.1.* where * is 1,2,3 .... Sunnetmask: 255.255.255.0 defauly getway: 192.168.1.231 Which is a server card and DNS address. preferred DNS Server: 192.168.1.231 In Advanced Tab under Wins: LMHostLookup is Unticked and default is radio buttoned. Ideally, I would have loved to have Disabled NETBIOS over TCP/IP but some network printers do not get accessed if this option is enabled(ie. Radio Buttoned). Bacause Disabling Netbios will drastically reduce traffic of NETBIOS broadcasting to all the computers on the net to do naming resolution. On Server, I have WINs Running which I have Scavanged Records, verified Database Integrity etc, removed Tombstoned Records etc. The Critical Errors shown only once a day when the server is statred are 4224(WINS) and 12923 - Server Licencing failed to Update DNS Record. I fail to understand as why do client machines HANG when they try to browse mapped network shared folders on K Drive. Kindly Advice

  Read the article

• Any reason not to disable the Windows pagefile given enough physical RAM?

  - by Evgeny

  The question of disabling the Windows pagefile has already been discussed quite a bit, for example here and here and here. People continue to upvote answers that say "you should not disable your pagefile even if you have plenty of RAM", but I have yet to see any concrete, verifiable reasons being given for this advice. As far as I can see, if you never need to read from the pagefile (because you have enough RAM) then performance could only be worse with it enabled due to Windows pre-emptively writing to it. At best, performance would be the same. I can't see how it could possibly be improved by writing data you never need to read. So my question is: Assuming that I have enough physical RAM for everything I do, is there any reason I should not disable the pagefile? Let's say the version of Windows is Windows XP x64 SP2 or Windows Server 2003 x64 SP2 (same thing). If it's different for Windows Server 2008 x64 I'd be interested to hear an answer for that as well. I'm looking for specific, objective reasons from good sources, not just opinions. Something like "here are the benchmarks done with and without a pagefile and the results were better with a pagefile, even with enough RAM" or "according to this MS KB article problem X occurs if you disable the pagefile". So far the only reasons I've seen mentioned are: Even if you think you have enough RAM you might run out. OK, but for the purposes of this question, let's just take it as a given that I have enough. Maybe I only ever read my email and I have 16GB RAM. Or 128GB. Or 1TB. Or whatever - but it's enough for 100% of what I do, 100% of the time. Another way to think of it is: if I have x MB physical RAM and y MB pagefile and I never run out of RAM in that configuration, would I not be better off, performance-wise, with x+y MB physical RAM and no pagefile? Windows is "used to" having a paging file and it might not function as reliably (from Understanding the Impact of RAM on Overall System Performance That's rather vague and I find it hard to believe, given that MS has provided the option to disable the pagefile. Windows knows what it's doing better than you. No - it doesn't know that I won't run more programs or load more data, but I do.

  Read the article

• Interop.Outlook.UserProperties.Add causing problem during connection time

  - by aanataliya

  Hi All, I have created a plug-in for outlook. Plug-in has only below code. private void OnNewOutlookInspector(Outlook.Inspector OutlookInsptr) { Outlook.MailItem MlItem = (Outlook.MailItem)OutlookInsptr.CurrentItem; //if I remove below line. Everything is working fine. MlItem.UserProperties.Add("INSPINIT", Outlook.OlUserPropertyType.olText , true , true ).Value = "1"; } public void OnConnection(object application, Extensibility.ext_ConnectMode connectMode, object addInInst, ref System.Array custom) { applicationObject = application; addInInstance = addInInst; MessageBox.Show("in connection new 2"); OutlkApp = (Outlook.Application)application; OutlkInsptrs = OutlkApp.Inspectors; OutlkInsptrs.NewInspector += new Outlook.InspectorsEvents_NewInspectorEventHandler(OnNewOutlookInspector); } Problem I am facing is, When I send HTML mail while plug-in is enabled, receiving end it is being received as a plain text. Below is the mail content along with the header and body at recieving end. x-sender: [email protected] x-receiver: [email protected] Received: from blr-s-07.pointcrossblr.com ([192.168.1.107]) by blr-ws-134.pointcrossblr.com with Microsoft SMTPSVC(6.0.2600.5949); Wed, 22 Dec 2010 17:11:02 +0530 Received: from blrws134 ([192.168.1.175]) by blr-s-07.pointcrossblr.com with Microsoft SMTPSVC(6.0.3790.4675); Wed, 22 Dec 2010 17:11:02 +0530 From: "Ashif Nataliya" <[email protected]> To: <[email protected]> Cc: <[email protected]> Subject: RTF FRM blr to pc.com cc blr-ws-134 Date: Wed, 22 Dec 2010 17:11:02 +0530 Message-ID: <[email protected]> MIME-Version: 1.0 Content-Type: multipart/mixed; boundary="----=_NextPart_000_00F7_01CBA1FB.36115580" X-Mailer: Microsoft Outlook 14.0 Content-Language: en-us X-MS-TNEF-Correlator: 00000000DCB2344DE8F50F4FBC91085BB5C06D55A4172000 thread-index: AcuhzRuTOBkvHPUnS1aLi9+cHNAWhA== Return-Path: [email protected] X-OriginalArrivalTime: 22 Dec 2010 11:41:02.0822 (UTC) FILETIME=[1C788860:01CBA1CD] This is a multipart message in MIME format. ------=_NextPart_000_00F7_01CBA1FB.36115580 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit HTML Test Test Mail ------=_NextPart_000_00F7_01CBA1FB.36115580 Content-Type: application/ms-tnef; name="winmail.dat" Content-Transfer-Encoding: base64 Content-Disposition: attachment; filename="winmail.dat" // and some other code..... Any help is appreciated. Thanks.

  Read the article

• Certain Programs cannot access internet

  - by Cindy

  Operating System: Windows 7 (x64) Problem: Certain Programs are unable to access the internet. They claim that there is no connection when you already are connected. Hello, before we start. Just letting you know I'm new here, and I'm very new to Windows 7. I installed it two days ago. I just installed Windows 7 on my laptop and I have a few problems. I play World of Warcraft, as well as a variety of games. And when I first attempt to log into the game, I get a windows error message, but it doesn't stop there. I thought World of Warcraft got corrupted during the upgrade. It seems that I am unable to access the internet from other online games as well. Most say in along the lines of "Cannot connect to patch server, try again later." I cannot use a downloader Also, I have internet explorer. The x32 version of the browser cannot connect to the internet, and when I try to enter "google.com", it says the same thing. I'm only accessing this site through Internet Explorer x64, which I would have been fine with is it's compatible with Adobe Flash. The only thing that seems to connect to the internet are Internet Explorer x64 and Windows Live Messenger. Here are the steps I have taken, but none worked. 1.) Disable Windows Firewall 2.) Have Windows Firewall Enabled, but allow the specific programs to access internet. And allowed all incoming access. 3.) Disabled UAC, Ran the programs as an admin, and set compatibility to Vista. 4.) Uninstalled an anti-virus program. (McAffee Security Suite 2010) 5.) Reinstalled the programs 6.) Reinstalled Windows 7 7.) Retaken the steps on the Administrator account. Please assist me in this problem. I need to get back into the game. Thanks so much in advance.

  Read the article

• Windows cannot find the host name "download.microsoft.com" using DNS

  - by joedotnot

  When trying to download a file found on the Microsoft downloads center that starts with, for example, http://download.microsoft.com/download/6/8/7/(some_GUID)/(some_file_name.ext) i get a timeout with "Internet Explorer cannot display the webpage". More information says: Internet connectivity has been lost. The website is temporarily unavailable. The Domain Name Server (DNS) is not reachable. The Domain Name Server (DNS) does not have a listing for the website's domain. If this is an HTTPS (secure) address, click Tools, click Internet Options, click Advanced, and check to be sure the SSL and TLS protocols are enabled under the security section. Diagnose Connection problems says: Windows cannot find the host name "download.microsoft.com" using DNS Bear with me while i expand on the problem: It all started when i tried to download Windows XP mode for my Windows 7 machine. I went to the virtual PC site, then thru the motions of Windows Genuine Advantage which validated ok, but when it redirects to grab the file just times out with above error. (NB: i also tried with the latest Chrome and Firefox but no use due to the Genuine Advantage stuff, so i decided to stick with IE). I am behind an ADSL2+ modem router connecting via wireless (Win 7 Pro laptop); so i hop over to the desktop connected via ethernet (Vista Business), and same result; begin to think site download.microsoft.com site is down. So i give it a break an read up on EDNS, flushing the cache, hosts file, etc... Try again an hour later on the Win 7 machine, still no go; so i turn off the Win 7 (software) firewall, and lo and behold, i can connect and grab any files from download.microsoft.com; (...nice, so we have a Micro$0ft firewall preventing access to a Micro$0ft website, no wonder my auto-updates kept failing but that's another story). But i still am not happy that the desktop connected via ethernet still cannot get to download.microsoft.com, even though i turned off all firewalls, defenders, anti-virus, etc. What is so special / specific about the url download.microsoft.com, any other site is ok, including www.microsoft.com. Any networking guru know what's REALLY going on, and how can i get the desktop to connect? Ping download.microsoft.com - Ping request could not find host download.microsoft.com. Please check the name and try again. Ping google.com or even www.microsoft.com works gives me an IP address. NB: On the wireless laptop ping download.microsoft.com works, i get xxxx.ms.akamai.net [202.7.177.33].

  Read the article

• "No route to host" with ssl but not with telnet

  - by Clemens Bergmann

  I have a strange problem with connecting to a https site from one of my servers. When I type: telnet puppet 8140 I am presented with a standard telnet console and can talk to the Server as always: Connected to athena.hidden.tld. Escape character is '^]'. GET / HTTP/1.1 <!DOCTYPE HTML PUBLIC "-//IETF//DTD HTML 2.0//EN"> <html><head> <title>400 Bad Request</title> </head><body> <h1>Bad Request</h1> <p>Your browser sent a request that this server could not understand.<br /> Reason: You're speaking plain HTTP to an SSL-enabled server port.<br /> Instead use the HTTPS scheme to access this URL, please.<br /> <blockquote>Hint: <a href="https://athena.hidden.tld:8140/"><b>https://athena.hidden.tld:8140/</b></a></blockquote></p> <hr> <address>Apache/2.2.16 (Debian) Server at athena.hidden.tld Port 8140</address> </body></html> Connection closed by foreign host. But when I try to connect to the same host and port with ssl: openssl s_client -connect puppet:8140 It is not working connect: No route to host connect:errno=113 I am confused. At first it sounded like a firewall problem but this could not be, could it? Because this would also prevent the telnet connection. As Firewall I am using ferm on both servers. The systems are debian squeeze vm-boxes. [edit 1] Even when I try to connect directly with the IP address: openssl s_client -connect 198.51.100.1:8140 #address exchanged connect: No route to host connect:errno=113 Bringing down the firewalls on both hosts with service ferm stop is also not helping. But when I do openssl s_client -connect localhost:8140 on the server machine it is connecting fine. [edit 2] if I connect to the IP with telnet it also is not working. telnet 198.51.100.1 8140 Trying 198.51.100.1... telnet: Unable to connect to remote host: No route to host The confusion might come from IPv6. I have IPv6 on all my hosts. It seems that telnet uses IPv6 by default and this works. For example: telnet -6 puppet 8140 works but telnet -4 puppet 8140 does not work. So there seems to be a problem with the IPv4 route. openssl seems to only (or by default) use IPv4 and therefore fails but telnet uses IPv6 and succeeds.

  Read the article

• SQL 2008 R2 Named Instance Client Connectivity Issues?

  - by Jerry Dodge

  We're upgrading our software from using SQL 2000 to 2008 R2. Our customers will be installing an update which uninstalls 2000 and installs 2008 R2 under the same instance. So if no instance existed, then no instance name will be set (default). However, the problem starts with the customers which have a named SQL instance. Starting in 2008 R2 (not sure of ones before), for some reason, a client connecting to the server by its instance name is unsuccessful. I'm testing from the Management Studio - if I can't connect this, then nothing can connect. I browse network servers, and find the specific server\instance in the list. But, upon trying to connect to an instance name like MyServer\INST, I get: A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: SQL Network Interfaces, error: 26 - Error Locating Server/Instance Specified) (Microsoft SQL Server, Error: -1) I do in fact have TCP/IP and Named Pipes protocols enabled, this is the first thing I did. When I connect to the server using a comma (,) and port number like MyServer, 49195, it works just fine. So it appears that client computers are just unable to identify the instance names. This has happened on all our installations of SQL 2008 R2 and from all client computers, including Win 7, XP, Vista, Server 2008, and Server 2003. We never experienced such issues on earlier versions of SQL. The problem even persists if the firewalls and antiviruses are all disabled. Now, this is a large update which we will be distributing soon to all our customers, and we want to minimize the interaction they need with us to get this installed. We absolutely hate the idea of using a port number, because it will always be different, and we would have to modify each client to point to this server/port. Some of our customers may have hundreds of client computers. How do I make client connections to a named SQL instance work again? After all, this is the whole purpose of named instances, and if a client can't connect to this instance by its name, then what is it even named for? EDIT It was mentioned to make sure SQL Browser is running, so I checked, and it is running. The server is also able to connect to its self (locally) - just external connections are refused. UPDATE After more careful checking, I learned the firewall wasn't completely disabled when testing, and upon disabling it completely, this works. So it appears that SQL Browser is being blocked by the firewall from external clients from accessing.

  Read the article

• Secure openVPN using IPTABLES

  - by bob franklin smith harriet

  Hey, I setup an openVPN server and it works ok. The next step is to secure it, I opted to use IPTABLES to only allow certain connections through but so far it is not working. I want to enable access to the network behind my openVPN server, and allow other services (web access), when iptables is disabaled or set to allow all this works fine, when using my following rules it does not. also note, I already configured openVPN itself to do what i want and it works fine, its only failing when iptables is started. Any help to tell me why this isnt working will appreciated here. These are the lines that I added in accordance with openVPN's recommendations, unfortunately testing these commands shows that they are requiered, they seem incredibly insecure though, any way to get around using them? # Allow TUN interface connections to OpenVPN server -A INPUT -i tun+ -j ACCEPT #allow TUN interface connections to be forwarded through other interfaces -A FORWARD -i tun+ -j ACCEPT # Allow TAP interface connections to OpenVPN server -A INPUT -i tap+ -j ACCEPT # Allow TAP interface connections to be forwarded through other interfaces -A FORWARD -i tap+ -j ACCEPT These are the new chains and commands i added to restrict access as much as possible unfortunately with these enabled, all that happens is the openVPN connection establishes fine, and then there is no access to the rest of the network behind the openVPN server note I am configuring the main iptables file and I am paranoid so all ports and ip addresses are altered, and -N etc appears before this so ignore that they dont appear. and i added some explanations of what i 'intended' these rules to do, so you dont waste time figuring out where i went wrong : 4 #accepts the vpn over port 1192 -A INPUT -p udp -m udp --dport 1192 -j ACCEPT -A INPUT -j INPUT-FIREWALL -A OUTPUT -j ACCEPT #packets that are to be forwarded from 10.10.1.0 network (all open vpn clients) to the internal network (192.168.5.0) jump to [sic]foward-firewall chain -A FORWARD -s 10.10.1.0/24 -d 192.168.5.0/24 -j FOWARD-FIREWALL #same as above, except for a different internal network -A FORWARD -s 10.10.1.0/24 -d 10.100.5.0/24 -j FOWARD-FIREWALL # reject any not from either of those two ranges -A FORWARD -j REJECT -A INPUT-FIREWALL -m state --state RELATED,ESTABLISHED -j ACCEPT -A INPUT-FIREWALL -p tcp -m tcp --dport 22 -j ACCEPT -A INPUT-FIREWALL -j REJECT -A FOWARD-FIREWALL -m state --state RELATED,ESTABLISHED -j ACCEPT #80 443 and 53 are accepted -A FOWARD-FIREWALL -m tcp -p tcp --dport 80 -j ACCEPT -A FOWARD-FIREWALL -m tcp -p tcp --dport 443 -j ACCEPT #192.168.5.150 = openVPN sever -A FOWARD-FIREWALL -m tcp -p tcp -d 192.168.5.150 --dport 53 -j ACCEPT -A FOWARD-FIREWALL -m udp -p udp -d 192.168.5.150 --dport 53 -j ACCEPT -A FOWARD-FIREWALL -j REJECT COMMIT now I wait :D

  Read the article

• Core i7 c1e and speedstepping - BSOD on shutdown

  - by DeaconDesperado

  I'm having an interesting problem with my recent Core i7 Digital Audio workstation build that I am curious to see if others have encountered. First, here are the specs on the machine. ASUS P6TD Deluxe Intel X58 Socket LGA1366 MB Intel Core i7-950 3.06Ghz 8M LGA1366 CPU CORSAIR DOMINATOR 6GB (3 x 2GB) 240-Pin DDR3 SDRAM DDR3 1600 Western Digital Caviar Black WD5001AALS 500GB Plus a couple ASUS optical drives and a 750W Corsair PSU. Running Windows 7 x64. All this is connected to the nefarious Digi 002 firewire audio interface for use with Pro Tools. I following mostly the specs posted by many other I7 users in the digidesign community who pooled their collective knowledge in this thread. Now after completing my build, I fell victim to the "UD5 squeal" described at that forum thread. So taking the advice posted, I disabled c1e advanced halt state and Intel speed stepping (I would likely have done this anyway to maintain a stable clock, power consumption isn't really a relevant concern on this machine.) I enabled XMP to set the ram timings properly as well. What I am experiencing is a BSOD upon shutdown, but only immediately after windows fully exits and ends all processes. The error is a MACHINE_CHECK_EXCEPTION 0x000000. The funny thing is that it is extremely intermitent and only occurs if the shutdown immediately followed a period of relative idleness. It does not a generate a minidump, I suspect because windows monitoring has terminated by the time this error occurs. No damage is evident and one can simply turn off manually and the system will act as though a proper shutdown had occurred. If anything it is a annoyance, I just want to be certain it is not affecting my long term stability. I have read that the i7 950 does not like DRAM voltages past 1.65, but that they are acceptable if they are within .5 of the BLCK setting. I have tried disabling XMP and setting all timings to auto and the problem still manifests in an identical way. It is suspect that the cpu idleness preceding shutdown is the determining factor, as both c1e and speedstepping are both settings intended to modify handling of this state. Any suggestions or prior experiences would be greatly appreciated. EDIT: The behavior very closely resembles what's described in this thread: http://www.tomshardware.com/forum/12003-63-shut-problem-windows The benign nature of it of is identical. I can't seem to download the hotfix cited there however.

  Read the article

• Windows 8 with LiveID login authenticates as Guest to remote SQl Server

  - by Tim Long

  I have a network where several users are using Office Accounting 2009 in multi-user client/server mode. OA is built on SQL Server. One PC acts as the 'server' and has the SQl Server instance, the others have only the application installed and no SQL instance, all of the apps connect remotely to the SQL instance on the 'server'. I'm using the term 'server' loosely here, it is just a normal workstation that happens to be designated as the server and runs the SQL instance. There is no NT domain, all user accounts are local accounts. The way that OA works in multi-user mode is that each user is required to have a local account with the same username and password on both the client and 'server' PCs. This has been working well, no along comes Windows 8. I use my 'Microsoft Account' aka LiveID to log into Windows 8. Office Accounting runs fine and attempts to connect to the database, but fails, 'you do not have permission to perform this operation'. In the SQL logs, I get this error: 2012-10-28 17:54:01.32 Logon Error: 18456, Severity: 14, State: 11. 2012-10-28 17:54:01.32 Logon Login failed for user 'SERVER\Guest'. Reason: Token-based server access validation failed with an infrastructure SERVER is the hostname of the server. So it seems to be authenticating as 'Guest'?? To verify this, I enabled the Guest account on the 'server' PC and then added Guest as an allowed user within Office Accounting (this simply creates the user in SQL and gives it an appropriate database role). Sure enough, My Windows 8 PC was then able to connect to the database when using Office Accounting. Clearly, having users authenticate as 'Guest' stinks from a security and auditing standpoint. So what I need are some ideas for how to work around this. I've tried switching the Windows 8 PC to a 'local account' and that works too, but requires giving up significant functionality on the Windows 8 PC. What I really need is a way to force the Windows 8 PC to use a specific set of credentials when connecting to the remote SQL instance. Office Accounting takes the logged in username, which is my LiveID and doesn't correspond to any Windows user name. Anyone solved this issue?

  Read the article

• LXC container can only access host via bridge

  - by vitaut

  I have an LXC container with i686 Ubuntu 12.04 running on a x86_64 Ubuntu 12.04 host. I've set up a bridge using instructions here. However the ping from the container only goes through to the host and not to other machines on the local network. Similarly only the host and not the other machines see the container OS. The host's /etc/network/interfaces file looks as follows: auto lo iface lo inet loopback iface eth0 inet manual auto br0 iface br0 inet dhcp bridge_ports eth0 bridge_fd 0 bridge_maxwait 0 The container's /etc/network/interfaces file looks as follows: auto lo iface lo inet loopback auto eth0 iface eth0 inet dhcp And here's the relevant part of the container's config: lxc.network.type=veth lxc.network.link=br0 lxc.network.flags=up Any ideas what I'm doing wrong? Additional info: The output of iptables-save on host: $ sudo iptables-save # Generated by iptables-save v1.4.12 on Sat Oct 26 06:06:48 2013 *filter :INPUT ACCEPT [6854:721708] :FORWARD ACCEPT [4067:538895] :OUTPUT ACCEPT [4967:522405] COMMIT # Completed on Sat Oct 26 06:06:48 2013 # Generated by iptables-save v1.4.12 on Sat Oct 26 06:06:48 2013 *nat :PREROUTING ACCEPT [82235:21547307] :INPUT ACCEPT [16:1070] :OUTPUT ACCEPT [9386:583359] :POSTROUTING ACCEPT [14693:1291952] -A POSTROUTING -s 10.0.3.0/24 ! -d 10.0.3.0/24 -j MASQUERADE COMMIT # Completed on Sat Oct 26 06:06:48 2013 The output of brctl show on host: $ brctl show bridge name bridge id STP enabled interfaces br0 8000.080027409684 no eth0 vethBkwWyV The output of ifconfig br0 on host: $ ifconfig br0 br0 Link encap:Ethernet HWaddr 08:00:27:40:96:84 inet addr:192.168.1.11 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:fe40:9684/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:232863 errors:0 dropped:0 overruns:0 frame:0 TX packets:59518 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:34437354 (34.4 MB) TX bytes:198492871 (198.4 MB) The output of ifconfig eth0 on host: $ ifconfig eth0 eth0 Link encap:Ethernet HWaddr 08:00:27:40:96:84 inet6 addr: fe80::a00:27ff:fe40:9684/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:299419 errors:0 dropped:0 overruns:0 frame:0 TX packets:203569 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:59077446 (59.0 MB) TX bytes:372056540 (372.0 MB) The output of ifconfig eth0 on container: $ ifconfig eth0 eth0 Link encap:Ethernet HWaddr 00:16:3e:74:08:2b inet addr:192.168.1.12 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::216:3eff:fe74:82b/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:81 errors:0 dropped:0 overruns:0 frame:0 TX packets:113 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:8506 (8.5 KB) TX bytes:9021 (9.0 KB)

  Read the article

• How to enable caching on Apache / Ubuntu Linux?

  - by Jim Mischel

  I have a large (several megabytes) XML file that's updated rather frequently (every 10 minutes or less) and gets a lot of traffic. I'd like to implement some caching to reduce bandwidth and server load. Looking at the Apache documents, I see a dizzying array of configuration options that involve various combinations of mod_expires, mod_headers, and mod_cache (and variants). I end up running in circles and the results aren't what I expect. I'm comfortable editing the various configuration files if I have some idea what I'm supposed to change. But at the moment I'm poking around in the dark and that's never a comfortable feeling. So, perhaps if I describe what I want, somebody here can take me by the hand and say, "This is what you need to do." Periodically, this file, call it "stuff.xml" is updated and a new version copied to the directory. The external url would be, for example, http://example.com/stuff.xml. Understand, this part works. Whenever I request the file, I get the expected result. But the file is big and I want to save bandwidth, so first I'd like to implement conditional GET semantics with the If-Modified-Since header. How do I do this? I've enabled mod_headers and mod_expired and added the <FilesMatching> section in my httpd.conf as recommended in countless examples I've seen online, but that didn't change the behavior when made a conditional GET request. I always get a status 200 with the entire document. So how the heck do I implement this? That'll cut down on neeless transfers. I'd also like to limit the amount of data transferred. Seeing as this is XML, gzipping it should save me 50% or more. My next step would be to somehow gzip the file and, if it's not too difficult, store it in memory. That'll cut down on per-access data transfer, and also reduce disk transfers. So how do I implement this type of caching? Thanks in advance.

  Read the article

• usb_modeswitch not switching

  - by deniz

  After I upgraded from kernel 2.6.18 to 3.5.3 modeswitch started not to work for me. Although lsusb shows my usb modem, usb_modeswitch does not switch it. My system information is like below. I ran lsusb, dmesg, usb-devices and usb_modeswitch their output is like below. usb_modeswitch instead of switching my modem it says "No devices in default mode found. Nothing to do. Bye.". Can you offer a solution? Kernel: Linux 3.5.3 usb_modeswitch: 1.2.3-1 usb_modeswitch-data: 20120120-1 usbutils: 006-1 libusb: 1.0.8-0.1 root@localhost$ lsusb Bus 002 Device 029: ID 12d1:1446 Huawei Technologies Co., Ltd. root@localhost$ dmesg [70112.477080] usb 2-1.4: new high-speed USB device number 30 using ehci_hcd [70112.567757] scsi49 : usb-storage 2-1.4:1.0 [70112.567842] scsi50 : usb-storage 2-1.4:1.1 [70113.571433] scsi 49:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2 [70113.572304] scsi 50:0:0:0: Direct-Access HUAWEI TF CARD Storage PQ: 0 ANSI: 2 [70113.574169] sr0: scsi-1 drive [70113.574223] sr 49:0:0:0: Attached scsi CD-ROM sr0 [70113.574250] sr 49:0:0:0: Attached scsi generic sg1 type 5 [70113.574350] sd 50:0:0:0: Attached scsi generic sg2 type 0 [70113.577173] sd 50:0:0:0: [sdb] Attached SCSI removable disk root@localhost$ usb-devices T: Bus=02 Lev=02 Prnt=02 Port=03 Cnt=01 Dev#= 30 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=12d1 ProdID=1446 Rev=00.00 S: Manufacturer=Huawei Technologies S: Product=HUAWEI Mobile C: #Ifs= 2 Cfg#= 1 Atr=c0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage I: If#= 1 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage root@localhost$ cat /etc/usb_modeswitch.d/12d1\:1446 # Huawei, newer modems TargetVendor= 0x12d1 TargetProductList="1001,1406,140b,140c,1412,141b,1433,1436,14ac,1506" MessageContent="55534243123456780000000000000011062000000100000000000000000000" root@localhost$ usb_modeswitch -c /etc/usb_modeswitch.d/12d1:1446 -v 12d1 -p 1446 -W * usb_modeswitch: handle USB devices with multiple modes * Version 1.2.3 (C) Josua Dietze 2012 * Based on libusb0 (0.1.12 and above) ! PLEASE REPORT NEW CONFIGURATIONS ! DefaultVendor= 0x12d1 DefaultProduct= 0x1446 TargetVendor= 0x12d1 TargetProduct= not set TargetClass= not set TargetProductList="1001,1406,140b,140c,1412,141b,1433,1436,14ac,1506" DetachStorageOnly=0 HuaweiMode=0 SierraMode=0 SonyMode=0 QisdaMode=0 GCTMode=0 KobilMode=0 SequansMode=0 MobileActionMode=0 CiscoMode=0 MessageEndpoint= not set MessageContent="55534243123456780000000000000011062000000100000000000000000000" NeedResponse=0 ResponseEndpoint= not set InquireDevice enabled (default) Success check disabled System integration mode disabled usb_set_debug: Setting debugging level to 15 (on) usb_os_find_busses: Skipping non bus directory devices usb_os_find_busses: Skipping non bus directory drivers usb_os_find_busses: Skipping non bus directory uevent usb_os_find_busses: Skipping non bus directory drivers_probe usb_os_find_busses: Skipping non bus directory drivers_autoprobe Looking for target devices ... No devices in target mode or class found Looking for default devices ... No devices in default mode found. Nothing to do. Bye. Thanks in advance.

  Read the article

< Previous Page | 232 233 234 235 236 237 238 239 240 241 242 243  | Next Page >