Search Results

Search found 10812 results on 433 pages for 'boot partition'.

Page 237/433 | < Previous Page | 233 234 235 236 237 238 239 240 241 242 243 244  | Next Page >

• What happens when the USB key or SD card I've installed VMware ESXi on fails?

  - by ewwhite

  An SD (SDHC) card installed in an HP ProLiant DL380p Gen8 server running VMware ESXi just failed. I encountered some rather ominous looking messages on the vCenter console and in the HP ProLiant ILO event log... Lost connectivity to the device ... backing the boot filesystem. As a result, host configuration changes will not be saved to persistent storage. Embedded Flash/SD-CARD: Error writing media 0, physical block 848880: Stack Exception. VMware advocates the use of USB and SD (SDHC) boot devices for ESXi. It was one of the main reasons the smaller footprint ESXi was developed (versus the older ESX). I've spent much time highlighting the differences between ESXi's installable and embedded modes to coworkers and clients. However, these failures do seem to happen. In this case, this is my third instance. Luckily, this is a vSphere cluster with SAN storage. What steps should be taken to remediate this failure?

  Read the article

• Booting From VIA VT6421A Based PCI SATA Card

  - by Priyan R

  I bought a VIA VT6421A based SATA card for an 845 chipset based motherboard. The card is working i can access sata hdd from windows/linux. The problem is i can't directly boot from the sata card. My motherboard is award bios 6 based. I tried first boot as SCSI, its not worked. There is no Raid Bios screen appeared from the card. On searching i found , Add VT6421A bios to system bios as pci addon bios. I did it using cbrom6 , successfully added VT6421A bios to the existing bios. But now on booting instead of raid bios system bios showed Warning : something like cannot load add on rom for vendor id xxxx device id xxx . Whats wrong ? As the card is VT6421A based and i added VT6421A bios got from VIA website.

  Read the article

• Xerox phaser 7760 prints gray as pink.

  - by Leif

  I have a Xerox phaser 7760 and 60 iMacs that dual boot xp and osx 10.5. They print without problem to other printers, but if you print to the 7760 anything gray scale comes out with a pink tint. This happens from all 60 computers windows or mac boot from any application. I have reinstalled the driver and run the color balance on the printer. The printer does fine on internal prints of gray for diagnostic pages. Any ideas on how to solve this?

  Read the article

• Windows 7 installation reboot loop

  - by Auswoolf

  Upgrading from Vista home premium to win 7 hoe premium from DVD ex Digital river on gigabyte VM900m; core 2 duo 2.13GHz 2GB ram; Western digital 250GB HD. Got as far as "Expanding Windows files ...100% the error message "Computer encountered unexpected error... To install windows press OK to restart computer and reinstall windows" The computer then reboots, loads Windows 7 (new logo) a essage that says "setup is starting services" then the error message comes back. I can get into BIOS to change boot priority but the computer just ignores this and goes through the same sequence. At the point of "to boot from CD/DVD press any key" my keyboard is deactivated and i cannot make a choice and the sae sequence occurs. I cannot break the sequence - I have push every key, disconnected every external device including HDMI screen, but nothing stops the loop. Any ideas? Auswoolf

  Read the article

• Windows 7 + Deep Freeze - I'm stuck in an endless reboot loop

  - by myermian

  I have the following setup: Windows 7 Ultimate Deep Freeze I "thawed" my machine last night and performed a Windows Update. The update is having issues (it gets stuck at 32%, fails, and restarts my machine). When it reboots it attempts it again, and again, and again, etc. (Endless loop). I looked online and found some solutions, but none of them seem to be working: When I run Safe Mode, Safe Mode w/ Network, or Safe Mode w/ Command Prompt it attempts to revert the Windows Update changes. However, the problem is with Deep Freeze on (and now in "Frozen" mode) the reverted changes don't stay, and I'm back into the loop of death. Oh, and side note: "Safe Mode w/ Command Prompt" does not actually take me to a command prompt window? Perhaps because it is attempting to complete the Windows Update changes first? I have tried to select the option to NOT restart when an windows error occurs, but it still does. I tried the remainder of all the other options in the F8 screen. The only other option left is to find my Windows 7 Media Disc (I can't find it right now) and use it to repair windows (because for some reason the repair option does not show up in the F8 screen). Is there a way to disable Deep Freeze from loading? When I selected "Safe Mode w/ Command Prompt" I noticed that it loads the DpFrz.sys file. I know that when I'm in the Windows Boot Manager if I press F10 instead of F8 (while highlighting Windows 7) it takes me to an "Edit Boot Options" screen: Edit Windows boot options for: Windows 7 Path: \Windows\system32\winload.exe Partition: 2 Hard Disk: 8e90e329 [ /NOEXECUTE=OPTIN (I CAN EDIT THIS LINE) ] Update: I found my Windows 7 Media Disk and it did not help out. The laptop had the "System Restore" as a partition on the HDD. I later received (in the mail) a Windows 7 Upgrade Disc from Sony to upgrade my system from Windows Vista to Windows 7 Ultimate. I placed the disc into the DVD drive and it does not come up as a "bootable" disc. I'm going to try to find an alternative disc to see if I can get into Command Prompt. Update 2: I got a Windows Repair disc and got into a command prompt window. I got into the registry and disabled Deep Freeze. Also: I renamed the Pending.xml file to Pending.old I cleared out the Windows Temp directory I still am stuck in the loop (though, it isn't an issue with DeepFreeze anymore because I can make changes to the hard drive and they persist). Not sure what to do at this point? Update 3: I ran the repair option and it couldn't repair, but it did point me to something. It says the error was due to a driver that was failing. I have a feeling it is my UPEK Fingerprint scanner.

  Read the article

• Restart Fibre channel controller after blade bootup IBM HS bladecentre

  - by Spence

  I have a remote system that needs to resume on startup. If the system is simply powered on then the blades boot before the SAN is online and then the only thing you can do is restart the systems. Is it possible to restart the fibre channel controller? That way I could have a system restart the controller after boot, connect to the SAN and then restart all servers requiring SAN information? Please note that I'm not a sys admin, just shooting for ideas to get a clean startup to work, apologies if my terminology is wrong.

  Read the article

• Can't connect to DeploymentShare$ from PC attempting to MDT, but can other PCs on the network

  - by Moman10

  I am in the process of setting up MDT and have run across a problem. MDT is installed on a Windows 2012 server, MDT version 6.2.5019.0. Using WDS as well. Active Directory domain, the server is up to date and on the network. I boot up the PC, it gets an address from DHCP, pulls down the LiteTouchPE_x64.wim image and goes into the MS Solution Accelerators screen, the Processing Bootstrap Settings box comes up and processes for a couple of seconds, then goes away, it sits there for another minute or so and then gives the error: A connection to the deployment share (\\Acme-MDT\DeploymentShare$) could not be made. Can not reach the DeployRoot. Possible Cause: Network Routing error or Network Configuration Error." I can then retry or cancel. I have seen this error online but so far nothing that helps fix it, but seems to be an issue with the FQDN. I verified that I am getting an IP address and that I can successfully ping the MDT server if I use the FQDN, but can not just by it's A record of Acme-MDT. I tried manually mapping the network share using net use and it works if I use the FQDN, but it fails with an error code 53, "Network path not found" if I just use the A record of Acme-MDT. Here is the net use command I'm using: net use * \\Acme-MDT\DeploymentShare$ /u:Domain\Administrator It gives the error System Error 53, Network path not found (and doesn't prompt for a password), but if I use the FQDN of \\Acme-MDT.domain.com\DeploymentShare$ it works fine to map the drive. I guess the problem is, when it tries to load the image, it is trying to start from \\Acme-MDT\DeploymentShare$ and I need it to start from \\Acme-MDT.domain.com\DeploymentShare$, but not sure how to get it to do that. I've put the fully qualified path in CustomSettings.ini and bootstrap, updated the deployment share, regenerated the boot image and replaced the boot wim in WDS. Or, if someone has an idea as to why it's acting this way and knows a way around it. The end result is what matters! :) I did verify in DNS that Acme-MDT is there, with the proper IP, and I can successfully use the net use command to map this drive from a couple other computers that are already on the network. I am assuming it has something to do with that computer not already being part of the domain, but I'm honestly at a loss as to how to fix it. Any ideas are appreciated, thanks in advance for your help!

  Read the article

• Windows 7 RTM vhd

  - by Mediator

  How can i dual boot XP and Windows 7 RTM vhd file in Windows XP without using any Windows 7 DVD?

  Read the article

• How do I get Windows 7 To Recognize a newly installed RAID 5 volume?

  - by GregH

  I had a previously running Windows 7 (64 bit) system. I added 3 new 1TB Seagate drives that I set up as a RAID 5 volume. I have a Gigabyte GA-P55M-UD2 motherboard. I installed the drives, set up the BIOS and configured the three drives as a RAID volume through the RAID setup utility that was accessed via Ctrl-I while the system was booting. I rebooted the system and could see the drives during the boot sequence. However, when Windows 7 was starting I got an error (quick blue screen) and then Windows tried to repair itself with no success. Do I need to install RAID drivers in Windows? How do I do it if Windows won't boot? Thanks in advance.

  Read the article

• Dual booting windows 8.1 and ubuntu

  - by Sriniketh

  I have a lenovo laptop with windows 8.1. I wanted to use ubuntu alongside windows. Hence, i downloaded the ubuntu 14.04 iso and created a live pendrive using Universal USB installer. I disabled secure boot and booted from the pendrive. All i get is the GNU GRUB command line version 2.X. I don't get a GUI for the GRUB and i don't know how to boot into ubuntu from the command line. I searched quite a few online forums but in vain. Can someone tell me how to proceed? Thanks in advance.

  Read the article

• HT Link Sync Error after Ubuntu 10.04 LTS Installation

  - by marklab

  Update 1 I just assembled an exact replica of this server, and successfully installed Ubuntu 10.04 LTS in a RAID10 configuration. The success was confirmed by a login to the initial account. There must be a hardware component that is faulty. Since the error mentions HT, which I believe to be Hyper Threading, I will start with the CPUs. Please indicate if this error is more strongly associated with any other piece of hardware. Or make a recommendation of another approach that would be good for this issue. Issue I was attempting to install Ubuntu 10.04 LTS on this system with the board RAID10 configured. However, the installation failed at the partitioning stage by rebooting the system. Upon reboot, there is an error report after POST listing the following: Node0: NB WatchDog Timer Error Node1: HT Link Sync Error Node2: HT Link Sync Error ... Node7: HT Link Sync Error Press F1 to continue/resume. After pressing F1 the system will boot from the Ubuntu 10.04 LTS installation disc. However, it will fail at the same stage, and go through the same process from there. Hardware CPU: AMD OPTERON X12 6172 G34 2.1G 18MB Motherboard: Supermicro H8QG6-F HDD: WD Caviar Green 2TB 5.4K RPM Troubleshooting I disabled RAID10 on the system, and installed the Ubuntu on a single drive. It installed successfully. I then went back to a RAID10 setup and attempted to install on the system again, and was able to make it through the partitioning stage. However, upon reboot, the system reported: Error: file not found, and then booted me into the Grub Rescue console. I feel I have aggravated the problem at this point because when I attempted to install from the boot disc again, the system reboots upon hitting enter to even start the installation process. It does the same thing when trying to boot from an Ubuntu 11 disc. I have not been able to find any information on this HT Link Sync Error, which I feel may have started the problems I am experiencing now with the installation of the OS. I am also aware that Ubuntu is said not to be supported by the motherboard according to Supermicro's site. However, since I was able to install it successfully on a single drive, I do not believe it is incompatible. I would like to know a reason for why it's failing to install on/off.

  Read the article

• Recover Windows 7 from Linux Ubuntu?

  - by macha

  I have two partitions and have Linux Ubuntu running on one partition and Windows 7 running on the other. Now when I try to boot from Windows 7, I get an error saying the /system32/winload.exe file is corrupted or deleted. Now I have Windows 7 files on my system but do not have the DVD, I have made USB bootable with Windows 7, but when I boot it with the USB stick, a blue screen is coming on with weird errors messages. Now I am trying to restore my Windows instance to a restore point where it can work normally. How can I do that in my situation?

  Read the article

• Computer crashes and won't start, LED indicator blinks slowly

  - by hexacyanide

  I have a MSI K8NGM2-FID motherboard coupled with a AMD Athlon 3700+ and an Antec TPII-550 power supply. The computer crashes at random times in operation, sometimes taking a while to crash, and sometimes crashing right after Windows XP shows the desktop after boot. The CPU temperature is always in the safe range, usually 30-33 degrees Celsius, and swapping the RAM has not done anything, so the crashes aren't cause by the RAM. What could be causing this? If the motherboard were fried, would the computer even boot at all? What causes inconsistent crashing of the computer? After the computer crashes, the LED power indicator blinks about once a second, and the computer does not respond to the power button. This behavior continues until the computer's power supply is completely removed.

  Read the article

• How can I make it difficult to install a new operating system on a certain computer?

  - by D W

  I want to host a website on a desktop computer running Ubuntu with a Windows virtual machine. I will give away the computer in exchange for a number of months of remote web hosting. I want to add some kind of lock (hardware or otherwise) so that the end users will have difficulty just reinstalling Windows and using the machine as they want, in contradiction to the contract. Ideally, I'd want the machine to die if reinstallation of the OS is attempted. It doesn't have to be completely insurmountable, but it has to be difficult enough to prevent casual reinstallation. Perhaps on bootup the system can check whether certain files exist on the computer and refuse to boot if they do not. I don't know if this is possible, but maybe BIOS is password protected, and searches for files before boot up. The files it looks for could be date sensitive, i.e. require remote replacement on a schedule.

  Read the article

• How do I recover from a Linux CentOS 4.6 Operating System Crash

  - by Greg Omebije

  Our x86 Linux server running CentOS4.6 has crashed. The machine boots only to the Grub prompt. We have tried using the "rescue mode" to recover the System, but it hasn't worked. How can we fix this problem, so that the machine boots normally? How can we fix this problem to the point were we can recover our files from the server Our Linux Server Configuration: Dell PowerEdge 1950 Intel Xeon 2 HDD (146GB each) 4GB RAM Hardware and Software raid setup CentOS 4.6 We used Sysrecord to boot the computer: the following are the output of fdisk -l Disk /dev/sda: 293.3 GB, 292326211584 255 heads, 63 sectors/track, 35539 Cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x00000080 Device Boot Start End Blocks Id System /dev/sda1 * 1 13 104391 83 Linux /dev/sda2 14 17769 142625070 8e Linux LVM

  Read the article

• How do I run unsigned driver permanently?

  - by acidzombie24

  I compiled my own truecrypt for windows and doing the suggested F8 to run unsigned drivers worked. I was able to install and run truecrypt successfully. However when i restart the machine and let it boot normally I can no longer use truecrypt because of unsigned drivers even though I have it installed. What can I do to boot normally and use my build of truecrypt? Can i modify the registry, add an exception, can i sign my own driver without paying anything (but it probably only work on my machine which is 100% fine), What can i do to run my own truecrypt build on a normal bootup?

  Read the article

• Installing raid controller forces reinstall of Windows Server 2008

  - by Tyler

  So, I've tried two different RAID controllers that have external SATA connections on my Server 2008 machine. I can install the hardware, boot into Windows, install the drivers and reboot again. No problems. However, as soon as I try to use eSATA-connected drives and reboot something happens to the Windows install and I can no longer boot into Windows. I tried repairing from the command line, and the end result is that repair console tells me I have 0 Windows installations (?). I end up having no choice but to reinstall Windows to get back on track. I must be doing something fundamentally wrong here, but I don't know what :(

  Read the article

• Hide non VHD partitions

  - by James

  Hey! I have two partition on my HDD: C and D. On D: I have a vhd image (with windows 7 ultimate) that I use to boot from. When I'm running the OS from VHD I can still access my physical parititons. Is it possible to dismount them, in order to see just the virtual disks in the VHD OS? I tried with the physical C and it says that I cannot dismount a boot paritition and I think D cannot be dismounted because the VHD is on it.

  Read the article

• grub-efi refuses to chainload Windows 8.1

  - by Alexei Averchenko

  I have installed LMDE (with grub in MBR) after I installed Windows 8.1. I then installed the grub-efi package and added the custom Windows options: #!/bin/sh exec tail -n +3 $0 menuentry "Windows" { search --fs-uuid --no-floppy --set=root A89A-7F4C chainloader (${root})/EFI/Boot/bkpbootx64.efi } menuentry "Windows (backup bootloader)" { search --fs-uuid --no-floppy --set=root A89A-7F4C chainloader (${root})/EFI/Microsoft/Boot/bkpbootmgfw.efi } These are basically a leftover from my older Ubuntu setup. However, grub is refusing to load them, complaining about the invalid signature. What do I do now?

  Read the article

• Static IPv4 and dynamic IPv6 on same interface

  - by Zsub

  I am trying to set up a CentOS 5.4 box to use a static IPv4 address, while getting a dynamic IPv6 address at boot time. I have only one interface, apart from the loopback interface, eth0. It has a static v4 and internet connectivity (I can SSH in). However, it doesn't get an IPv6 by default. I have enabled IPv6 in /etc/sysconfig/network and I have added IPV6INIT=yes to the config in /etc/sysconfig/networking/devices/. If I use dhcp6c it does get a valid IPv6 address, but the main question is how do I configure it to get one at boot-time?

  Read the article

• Ubuntu Lucid startup events

  - by Lakshman Prasad

  On starting up Ubuntu, I seem to have to do the following, all the time: Enter the password for the keyring to unlock, so that it connects to wifi Enable the "Extra" Visual effects from the Appearances preferences Start skype. How can I automate all of these. Bonus points, if I can use the existing chat bundled in the system to use my skype account. Also, since I dual boot, I get the grub options initially to select Windows or Ubuntu that waits for 10 seconds for me to choose. How do I make it go to ubuntu, unless I explicitly not press a key to boot to windows. Thanks in advance.

  Read the article

• Ubuntu Lucid startup events

  - by becomingGuru

  On starting up Ubuntu, I seem to have to do the following, all the time: Enter the password for the keyring to unlock, so that it connects to wifi Enable the "Extra" Visual effects from the Appearances preferences Start skype. How can I automate all of these. Bonus points, if I can use the existing chat bundled in the system to use my skype account. Also, since I dual boot, I get the grub options initially to select Windows or Ubuntu that waits for 10 seconds for me to choose. How do I make it go to ubuntu, unless I explicitly not press a key to boot to windows. Thanks in advance.

  Read the article

• CentOS 5.7 keeps rebooting after fresh installation

  - by Wagner Maestrelli

  I have just installed CentOS 5.7 x86_64 on a new computer. The installation went on without any issues. But, after it finnished, the machine started to show an awkward behaviour: it restarts every time it tries to boot. It happens after all the services have been started. The screen just goes black and it shows an error message from the monitor: Input not supported. And then it reboots. I took a look at the logs, but I couldn't manage to find anything. Any help? Update Before doing the hardware diagnosis, as pointed out, I decided to make some tests. First, I changed the runlevel to 3, adding the 3 parameter at the end of the kernel command. Then, after logging in in text mode, I checked the xorg.conf file out for some problems regarding the screen resolution. There was nothing unexpected set. Well, if there had to be a problem with it, I couldn't start the X server at the command line, right? So, I typed startx and Gnome started! So, probably, it's not an issue with the screen resolution, I suppose. Then I selected the Log Out root... Gnome menu option and something odd happened: the screen went black, the Input not supported monitor error message was displayed and the system rebooted. Yes, the same problem I was having while trying to boot! After that, I decided to try yet another test: I removed the rhgb quiet parameters from the kernel command to see if some error would show up. Well, to my surprise, the boot went on without problems! The Gnome login screen showed up, I logged in and the session started. But then I selected the Shut Down... menu option and guess what? Same problem: black screen, same monitor error and the system rebooted. Yes, it rebooted, it did not shut down. I repeated both of the tests and the behaviours were the same. I really don't know what's going on. It seems to be an issue regarding the changing of the screen mode or something like that. Any ideas? Could this be a hardware problem? Or does it seem to be something regarding the system configuration?

  Read the article

• Missing over 100GB of Space on sda1 RHEL

  - by WifiGhost

  I have a server setup with a RAID 5 using (3) 500GB drives, 1 as a spare so unused in the RAID. So in my mind i start out with 990GB with the RAID 5 in place. When looking at DF or the built in disk space utility i only see a total of about 882GB, how can i find where the 100+GB went? How can i get it back? I've checked the RAID 5 BIOS and i see all the space. I've tried looking manually and through terminal commands with no luck. Filesystem - 1K-blocks - Used Available - Use% - Mounted on /dev/mapper/vg_web-lv_root 838084192 48368700 747153060 7% / tmpfs 12104644 592 12104052 1% /dev/shm /dev/sda1 495844 121546 348698 26% /boot /dev/mapper/vg_web-lv_home 82569904 259136 78116468 1% /home Filesystem Size Used Avail Use% Mounted on /dev/mapper/vg_web-lv_root 800G 47G 713G 7% / tmpfs 12G 592K 12G 1% /dev/shm /dev/sda1 485M 119M 341M 26% /boot /dev/mapper/vg_web-lv_home 79G 254M 75G 1% /home

  Read the article

• Wiping out user and/or root password in embedded linux

  - by TryTryAgain

  We have a security camera system running an embedded linux. It boots with Lilo as a bootloader and has no tty access once booted. I don't know any username either. SSH/22 is open, but I don't think brute force is an option. I have tried all the common tricks to reset a linux user password (boot from the bootloader in single user mode = doesn't happen, still prompts for user login, boot to a live cd = can't access the file system...it's all loop files and other binary, etc etc), but they are all not possible as it is an embedded linux setup the way it is. Any help/suggestions would be appreciated. Thanks

  Read the article

< Previous Page | 233 234 235 236 237 238 239 240 241 242 243 244  | Next Page >