Search Results

Search found 8567 results on 343 pages for 'commands unix'.

Page 237/343 | < Previous Page | 233 234 235 236 237 238 239 240 241 242 243 244  | Next Page >

  • Difficulty Mounting Volumes on a Partitioned External HD

    - by Todd
    I'm having a great deal of difficulty with an external hard drive. I'm currently running a dual boot system (XP Service Pack 3 and Ubuntu 11.04 Natty Narwahl) on a Dell Inspiron B120. I'm trying to set up a new 80 GB Hitachi external HD. Using GParted, I formatted the drive and set up the partitions. The partitioning scheme is as follows 10GB NTFS Primary, 2GB Linux-Swap Primary, 50GB FAT32 Primary, 12GB Unallocated. After applying those changes, I went into Disk Utility and the HD appears along with the correct partitions. When I try to mount the volumes for partitions 1 and 3, I get a pop-up stating: Error Mounting Volume An error occurred while performing an operation on "Home" (Partition 3 of HTS548080m9AT00): The daemon is being inhibited. When I try to to check the filesystem I get a pop-up stating: Error Checking filesystem on volume An error occurred while performing an operation on "Home" (Partition 3 of HTS548080m9AT00): The daemon is being inhibited. Throughout the time that I'm attempting to troubleshoot the problem, the external drive light is on and blinking. With my frustration hitting a boiling point, I try to shut down the drive and remove it so that I can plug in a different external HD that works PERFECTLY. However, when I try to shut down and safely remove the drive, I get a pop-up stating: Error Detaching Drive An error occurred while performing an operation on "80GB Hard Disk" (HTS548080m9AT00): The daemon is being inhibited. Can anyone tell me what I'm doing wrong? I'm a newbie and not that skilled with terminal commands, so please dumb it down for me if you request specific command output.

    Read the article

  • Correct nvidia+intel graphics setup in 14.04

    - by Espressofa
    Just upgraded to 14.04 to try to fix some other issues. Now, something has gone wrong with my graphics. I have a Thinkpad T530 with Intel and Nvidia graphics cards. $ inxi -SGx System: Host: xyz Kernel: 3.13.0-24-generic x86_64 (64 bit, gcc: 4.8.2) Desktop: N/A Distro: Ubuntu 14.04 trusty Graphics: Card-1: Intel 3rd Gen Core processor Graphics Controller bus-ID: 00:02.0 Card-2: NVIDIA GF108M [NVS 5400M] bus-ID: 01:00.0 X.Org: 1.15.1 drivers: fbdev,vesa,intel,nouveau (unloaded: nvidia) Resolution: [email protected] GLX Renderer: N/A GLX Version: N/A Direct Rendering: N/A $ glxinfo name of display: :0 Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Error: couldn't find RGB GLX visual or fbconfig Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Error: couldn't find RGB GLX visual or fbconfig Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". I'm not sure what I did but now something is wrong with my graphics, as should be visible from the above commands. nvidia-detector says "none" as well. I used to have bumblebee but then some website said to remove it and now something's clearly wrong. What's the right way to set things up? Should I try to add bumblebee back? Here's what's installed now: $ dpkg --get-selections | grep nvidia nvidia-319 install nvidia-331 install nvidia-libopencl1-331 install nvidia-opencl-icd-331 install nvidia-prime install nvidia-settings install nvidia-settings-319 install

    Read the article

  • Procedure or function has too many arguments specified

    - by bullpit
    This error took me a while to figure out. I was using SqlDataSource with stored procedures for SELECT and UPDATE commands. The SELECT worked fine. Then I added UPDATE command and while trying to update, I would get this error: "Procedure of function has too many arguments specified" Apparently, good guys at .NET decided it is necessary to send SELECT parameters with the UPDATE command as well. So when I was sending the required parameters to the UPDATE sp, in reality, it was also getting my SELECT parameters, and thus failing. I had to add the extra parameters in the UPDATE stored procedure and make them NULLABLE so that they are not required....phew... Here is piece of SP with unused parameters. ALTER PROCEDURE [dbo].[UpdateMaintenanceRecord]        @RecordID INT     ,@District VARCHAR(255)     ,@Location VARCHAR(255)         --UNUSED PARAMETERS     ,@MTBillTo VARCHAR(255) = NULL     ,@SerialNumber VARCHAR(255) = NULL     ,@PartNumber VARCHAR(255) = NULL Update: I was getting that error because unkowingly, I had bound the extra fields in my GridVeiw with Bind() call. I changed all the extra one's, which did not need to be in Update, to Eval() and everything works fine.

    Read the article

  • Issues with Cinnamon?

    - by Corrodie
    I just recently switched my system over to Ubuntu 12.10, and decided on Cinnamon as my environment-- it all worked fine, at first. But I was poorly educated and started using Compiz and Emerald along with it--Setting both as replacements in startup processes. I now know, that's a big, big mistake. Now when loading Cinnamon, I am greeted to my background image, and only that. My only options seem to be to open a terminal. I was advised to attempt muffin --replace and mutter --replace Neither to any avail, the terminal closes, and I cannot load another one unless I completely reload. I went back to Unity, purged and autoremoved Cinnamon, emerald, and compizconfig, and attempted to reinstall Cinnamon, thinking that would solve the problem--no, it came back just as broken as before. So, I reinstalled ubuntu, then cinnamon---still broken. I'm assuming I must find a way to remove the replace commands-- but as I have no menu, I'm not positive I can do that. Is there any way I can access the startup processes via terminal? I'd think though, if I completely removed Cinnamon, all configurations would be gone too, so, it's just not making much sense. Is there some kind of reset I could possibly do? I've been browsing forums and questions here, all leading to things I'd already done, so, it can't hurt to ask for myself. I apologize if you would rather I have posted this over at mint. Next time, I will definitely check compatibility instead of assuming something just has to work. Any help is greatly appreciated, thanks! ****EDIT***** It seems although it didn't allow me to do it before, I was now allowed to access the settings and startup processes for Cinnamon via Unity, and, after quickly removing aforementioned processes- I'm up and running again.

    Read the article

  • Beginning with shell scripting

    - by Kevin Wyman
    I am fresh into Ubuntu and one of my goals is shell scripting for personal (and maybe public) use. I'm a novice, though I do understand some of the basics (e.g. what a variable, string, loop, etc... is) but to get the most of scripting I need to learn in-depth. I figure the best way to do that is to jump right into scripting and ask questions only pertinent to the stage I am at in my attempted script. Scenario: I have edited my sudoers file to allow my non-root user to run sudo commands without being prompted for a password. Question: In vim, what would be the best code to use for a function that checks whether this condition is [true], If not, prompt the user if they want the script to edit and save the sudoers file to make this condition [true]? Layout - If condition is true, carry-on with rest of script. If condition is not true, the script silently edits/adds the line: %sudo ALL=(ALL:ALL) NOPASSWD: ALL in the sudoers file, saves and then continues on with the next part of the script. Any help with this would be greatly appreciated and assist me in my journey to writing shell scripts.

    Read the article

  • "The daemon is being inhibited" error message when mounting volumes on a partitioned external HD [closed]

    - by Todd
    I'm having a great deal of difficulty with an external hard drive. I'm currently running a dual boot system (XP Service Pack 3 and Ubuntu 11.04 Natty Narwahl) on a Dell Inspiron B120. I'm trying to set up a new 80 GB Hitachi external HD. Using GParted, I formatted the drive and set up the partitions. The partitioning scheme is as follows 10GB NTFS Primary, 2GB Linux-Swap Primary, 50GB FAT32 Primary, 12GB Unallocated. After applying those changes, I went into Disk Utility and the HD appears along with the correct partitions. When I try to mount the volumes for partitions 1 and 3, I get a pop-up stating: Error Mounting Volume An error occurred while performing an operation on "Home" (Partition 3 of HTS548080m9AT00): The daemon is being inhibited. When I try to to check the filesystem I get a pop-up stating: Error Checking filesystem on volume An error occurred while performing an operation on "Home" (Partition 3 of HTS548080m9AT00): The daemon is being inhibited. Throughout the time that I'm attempting to troubleshoot the problem, the external drive light is on and blinking. With my frustration hitting a boiling point, I try to shut down the drive and remove it so that I can plug in a different external HD that works PERFECTLY. However, when I try to shut down and safely remove the drive, I get a pop-up stating: Error Detaching Drive An error occurred while performing an operation on "80GB Hard Disk" (HTS548080m9AT00): The daemon is being inhibited. Can anyone tell me what I'm doing wrong? I'm a newbie and not that skilled with terminal commands, so please dumb it down for me if you request specific command output.

    Read the article

  • Delaying a Foreach loop half a second

    - by Sigh-AniDe
    I have created a game that has a ghost that mimics the movement of the player after 10 seconds. The movements are stored in a list and i use a foreach loop to go through the commands. The ghost mimics the movements but it does the movements way too fast, in split second from spawn time it catches up to my current movement. How do i slow down the foreach so that it only does a command every half a second? I don't know how else to do it. Please help this is what i tried : The foreach runs inside the update method DateTime dt = DateTime.Now; foreach ( string commandDirection in ghostMovements ) { int mapX = ( int )( ghostPostition.X / scalingFactor ); int mapY = ( int )( ghostPostition.Y / scalingFactor ); // If the dt is the same as current time if ( dt == DateTime.Now ) { if ( commandDirection == "left" ) { switch ( ghostDirection ) { case ghostFacingUp: angle = 1.6f; ghostDirection = ghostFacingRight; Program.form.direction = ""; dt.AddMilliseconds( 500 );// add half a second to dt break; case ghostFacingRight: angle = 3.15f; ghostDirection = ghostFacingDown; Program.form.direction = ""; dt.AddMilliseconds( 500 ); break; case ghostFacingDown: angle = -1.6f; ghostDirection = ghostFacingLeft; Program.form.direction = ""; dt.AddMilliseconds( 500 ); break; case ghostFacingLeft: angle = 0.0f; ghostDirection = ghostFacingUp; Program.form.direction = ""; dt.AddMilliseconds( 500 ); break; } } } }

    Read the article

  • Architecture of an action multiplayer game from scratch

    - by lcf
    Not sure whether it's a good place to ask (do point me to a better one if it's not), but since what we're developing is a game - here it goes. So this is a "real-time" action multiplayer game. I have familiarized myself with concepts like lag compensation, view interpolation, input prediction and pretty much everything that I need for this. I have also prepared a set of prototypes to confirm that I understood everything correctly. My question is about the situation when game engine must be rewind to the past to find out whether there was a "hit" (sometimes it may involve the whole 'recomputation' of the world from that moment in the past up to the present moment. I already have a piece of code that does it, but it's not as neat as I need it to be. The domain logic of the app (the physics of the game) must be separated from the presentation (render) and infrastructure tools (e.g. the remote server interaction specifics). How do I organize all this? :) Is there any worthy implementation with open sources I can take a look at? What I'm thinking is something like this: -> Render / User Input -> Game Engine (this is the so called service layer) -> Processing User Commands & Remote Server -> Domain (Physics) How would you add into this scheme the concept of "ticks" or "interactions" with the possibility to rewind and recalculate "the game"? Remember, I cannot change the Domain/Physics but only the Game Engine. Should I store an array of "World's States"? Should they be just some representations of the world, optimized for this purpose somehow (how?) or should they be actual instances of the world (i.e. including behavior and all that). Has anybody had similar experience? (never worked on a game before if that matters)

    Read the article

  • Oracle R Distribution 2-13.2 Update Available

    - by Sherry LaMonica
    Oracle has released an update to the Oracle R Distribution, an Oracle-supported distribution of open source R. Oracle R Distribution 2-13.2 now contains the ability to dynamically link the following libraries on both Windows and Linux: The Intel Math Kernel Library (MKL) on Intel chips The AMD Core Math Library (ACML) on AMD chips To take advantage of the performance enhancements provided by Intel MKL or AMD ACML in Oracle R Distribution, simply add the MKL or ACML shared library directory to the LD_LIBRARY_PATH system environment variable. This automatically enables MKL or ACML to make use of all available processors, vastly speeding up linear algebra computations and eliminating the need to recompile R.  Even on a single core, the optimized algorithms in the Intel MKL libraries are faster than using R's standard BLAS library. Open-source R is linked to NetLib's BLAS libraries, but they are not multi-threaded and only use one core. While R's internal BLAS are efficient for most computations, it's possible to recompile R to link to a different, multi-threaded BLAS library to improve performance on eligible calculations. Compiling and linking to R yourself can be involved, but for many, the significantly improved calculation speed justifies the effort. Oracle R Distribution notably simplifies the process of using external math libraries by enabling R to auto-load MKL or ACML. For R commands that don't link to BLAS code, taking advantage of database parallelism using embedded R execution in Oracle R Enterprise is the route to improved performance. For more information about rebuilding R with different BLAS libraries, see the linear algebra section in the R Installation and Administration manual. As always, the Oracle R Distribution is available as a free download to anyone. Questions and comments are welcome on the Oracle R Forum.

    Read the article

  • Can I install new version of Ubuntu in spair RAIDed partition with unetbootin

    - by artfulrobot
    I have Ubuntu 11.04 running on my home desktop which has 2 hard drives mirrored by RAID. The drives are partitioned with a big data partition, a swap partition and a couple of 20Gb partitions for OSes, one is 11.04 which is in use, and the other is kept spare for installing a later version. Which is what I'd like to do now. The idea of a 2nd partition for new OS is that I can try it, and if it's problematic, I can boot back into the original one - the machine is shared with others, so I need it to stay available! I have had horrible problems with software RAID after using a Live USB stick - basically it messes up the internal numbering of the RAID drives or something, anyway, the result is you can't boot after using it :-( and have to spend ages re-assembling the arrays, trying to remember grub commands etc etc. Quite a shocker when you consider booting from a Live USB is supposed not to affect the existing system. As I'm installing in a RAIDed disc, I would typically use the Alternative install (sad to hear that this is going to be dropped in future). However, I think I might be able to use unetbootin to trick the system into working on top of the existing system that understands RAID, with the normal ISO? If unetbootin loads from drives that are already understood to be RAIDED, then presumably it will only see md0... instead of sda, sdb... and as long as I don't need to repartition (I don't) it should be fine, right? Or is that just plain foolishness? Please tell me before I end up with a dead system (again!)

    Read the article

  • How do I disable touchpad tap to click?

    - by AWE
    You've heard this a million times but the "tap to click" is a pain in the behind and I want to disable it. There is no touchpad in gpointing-device-settings and neither in mouse and touchpad in system settings. I've tried some commands in terminal but it's all crap. Dconf-editor doesn't react. How about solving this once and for all? xinput list: ? Virtual core pointer id=2 [master pointer (3)] ? ? Virtual core XTEST pointer id=4 [slave pointer (2)] ? ? PS/2 Generic Mouse id=13 [slave pointer (2)] ? Virtual core keyboard id=3 [master keyboard (2)] ? Virtual core XTEST keyboard id=5 [slave keyboard (3)] ? Power Button id=6 [slave keyboard (3)] ? Video Bus id=7 [slave keyboard (3)] ? Video Bus id=8 [slave keyboard (3)] ? Power Button id=9 [slave keyboard (3)] ? Sleep Button id=10 [slave keyboard (3)] ? Laptop_Integrated_Webcam_HD id=11 [slave keyboard (3)] ? AT Translated Set 2 keyboard id=12 [slave keyboard (3)] ? Dell WMI hotkeys id=14 [slave keyboard (3)]

    Read the article

  • How to install .deb file from within preinst script

    - by Ashwin D
    I have my own application packaged using dpkg. The application depends on several deb files which I'm trying to install from within the preinst script of my application. The preinst script checks if a dependent deb file is installed, if not it goes to installt it using the dpkg -i command. This is repeated for all the dependent deb files needed by the main application. When I try to install the main application using dpkg -i, the commands returns failure when trying to execute the preinst script. Below is that error message. dpkg: error: dpkg status database is locked by another process I deleted /var/lib/dpkg/lock file and retried to install the application. But to no avail. If I run the preinst script separately like any other shell script, it runs without any issue. All the deb files will be installed properly. So, the issue is only when this preinst script is being run automatically by the dpkg -i command. I'm lost trying to determine the root cause. If anyone can shed some light on what the real issue might be, their help will be greatly appreciated. Thank you. Ashwin

    Read the article

  • Ubuntu installation does not recognize drive partinioning

    - by Woltan
    I have a 1TB drive and installed Windows 7 on a 128GB partition. When I now try to install Ubuntu 11.04 it does not recognize the Windows partition but offers the complete 1TB drive to install Ubuntu on instead. It displays: However, in the Ubuntu Disk Utility the Windows partitions are recognized. What do I need to do in order for Ubuntu to recognize the Windows 7 partition and install Ubuntu as a dual boot? Response to comments The following commands were executed and the results are shown below: fdisk -l WARNING: GPT (GUID Partition Table) detected on '/dev/sda'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x34a38165 Device Boot Start End Blocks Id System /dev/sda1 * 1 13 102400 7 HPFS/NTFS Partition 1 does not end on cylinder boundary. /dev/sda2 13 16318 130969600 7 HPFS/NTFS Disk /dev/sdb: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x14a714a6 Device Boot Start End Blocks Id System /dev/sdb1 1 60801 488384001 83 Linux parted -l Warning: Unable to open /dev/sr0 read-write (Read-only file system). /dev/sr0 has been opened read-only. Error: /dev/sr0: unrecognised disk label

    Read the article

  • Ubuntu 12.10 with kernel 3.5.0-18

    - by Chaitanya
    I had ubuntu 12.04 with kernel 3.0.2. Today I have updated my system and got 12.10 with kernel 3.5.0-18. Now when I boot my machine with 3.5 kernel, it starts until the page where I enter my password. Within seconds, I get a page with looooong list of some commands or list. I cant take screenshot of that. It looks something like, [1.2234978942837]kjsahfa;lsfksld;fkjsf;owieurwirejw/rnw;erkjwelrjw2309480432 [1.3294823498230948]as;lfjsf;iuwrijrwjlkerjw;rekwer;lkwjre;lkjRIJWEORIWE'JJA; something like this. Luckily, in my boot page, I have 3.0.2 kernel also. When I boot with 3.0.2 kernel there is no problem. But when I boot with 3.5.0, it throws that wierd error. I wont be able to do anything at that time. None of the keys work. I have to forcibly shutdown the machine and restart with 3.0.2 kernel. Please help..... Thanks, Chaitanya.

    Read the article

  • Really slow wireless internet on 12.04 with HP dv6 6070ca

    - by Joe
    I was recently running the previous version of Ubuntu through Wine, and everything was working great. I decided to upgrade to pangolin when I saw it came out. After upgrading the internet was very slow (the estimated time on the updates was something like 4 days). I thought maybe this had something to do with the Wine installation, so I decided to finally do an actual dual boot. I partitioned my drive all nice and neat, but I made the mistake of connecting to the internet for the installation, and clicking the option to install updates and restricted extras. This was in the morning, circa 6 am. Fast forward to the evening, the installation is frozen at around 75%. In frustration I gave the ol girl a hard shut-down, which effectively rendered my machine useless. I used the thumb drive to reinstall Ubuntu, this time without connecting to the internet. Installed nice and easy, no problems, but the internet is still ridiculously slow. It took me about 20 minutes of frustration and hitting stop and reload repeatedly to even get this question page to open. This is important to me as now Windows won't even boot and I have to use ubuntu for the time being but I can't even bear to turn on my laptop due to the frustration that immediately ensues. Please help! Oh, and I'm relatively new so if there are some terminal commands that spew out info you guys would find useful let me know what they are and I'll post back the information.

    Read the article

  • Design pattern for an automated mechanical test bench

    - by JJS
    Background I have a test fixture with a number of communication/data acquisition devices on it that is used as an end of line test for a product. Because of all the various sensors used in the bench and the need to run the test procedure in near real-time, I'm having a hard time structuring the program to be more friendly to modify later on. For example, a National Instruments USB data acquisition device is used to control an analog output (load) and monitor an analog input (current), a digital scale with a serial data interface measures position, an air pressure gauge with a different serial data interface, and the product is interfaced through a proprietary DLL that handles its own serial communication. The hard part The "real-time" aspect of the program is my biggest tripping point. For example, I need to time how long the product needs to go from position 0 to position 10,000 to the tenth of a second. While it's traveling, I need to ramp up an output of the NI DAQ when it reaches position 6,000 and ramp it down when it reaches position 8,000. This sort of control looks easy from browsing NI's LabVIEW docs but I'm stuck with C# for now. All external communication is done by polling which makes for lots of annoying loops. I've slapped together a loose Producer Consumer model where the Producer thread loops through reading the sensors and sets the outputs. The Consumer thread executes functions containing timed loops that poll the Producer for current data and execute movement commands as required. The UI thread polls both threads for updating some gauges indicating current test progress. Unsure where to start Is there a more appropriate pattern for this type of application? Are there any good resources for writing control loops in software (non-LabVIEW) that interface with external sensors and whatnot?

    Read the article

  • Disable discrete AMD GPU

    - by Smajl
    My notebook has two graphic cards and it suffers from severe overheating after installing Ubuntu (no problem with Windows 7 on the same machine). I figured out that the problem may be in the graphic card and I would like to disable the discrete one. I followed some tutorials on this topic (for example http://planetoss.com/articles/how-to-disable-the-discrete-amd-graphics-card-in-linux/). But the problem is, that after executing the commands, nothing really happens and both GPU are still running. Here is what I have done: smajl@smajl-mini:~$ sudo chown smajl /sys/kernel/debug/vgaswitcheroo/switchsmajl@smajl-mini:~$ echo IGD > /sys/kernel/debug/vgaswitcheroo/switch smajl@smajl-mini:~$ sudo cat /sys/kernel/debug/vgaswitcheroo/switch 0:IGD:+:DynPwr:0000:01:05.0 1:DIS-Audio: :Pwr:0000:02:00.1 2:DIS: :DynPwr:0000:02:00.0 smajl@smajl-mini:~$ echo OFF > /sys/kernel/debug/vgaswitcheroo/switch smajl@smajl-mini:~$ sudo cat /sys/kernel/debug/vgaswitcheroo/switch 0:IGD:+:DynPwr:0000:01:05.0 1:DIS-Audio: :Pwr:0000:02:00.1 2:DIS: :DynPwr:0000:02:00.0 What am I missing here? Also, more on the overheating topic: 1) Installed TLP 2) updated system 3) set power setting mode to "power save" ...and nothing helps Tried same thing with Linux Mint without success. Is there anything else to try if I manage to disable the second GPU and the problem preserves? Otherwise I would have to get back to win in order not to melt my laptop.. :-/

    Read the article

  • BCM2046B1 Bluetooth Dongle connection problem

    - by Andfoy
    Well i have a Blueooth dongle with an BCM2046 IC intrregated, my problem is that when i connect it, Ubuntu recognize it, but it don't work whe i try to scan or scan the PC from other device, i replaced the default Gnome Bluetooth manager and i installed Blueman, but the problem presists. The Bluetooth LED indicator appears to be "working". I'm using 11.10 Oneiric Ocelot hcitool dev: Devices: hci0 89:21:XX:XX:XX:XX lsusb: Bus 002 Device 003: ID 0a5c:4500 Broadcom Corp. BCM2046B1 USB 2.0 Hub (part of BCM2046 Bluetooth) Bus 002 Device 004: ID 0a5c:2100 Broadcom Corp. Bluetooth 2.0+eDR dongle hciconfig -a: hci0: Type: BR/EDR Bus: USB BD Address: 89:21:XX:XX:XX:XX ACL MTU: 1017:8 SCO MTU: 64:0 UP RUNNING PSCAN ISCAN RX bytes:1329 acl:0 sco:0 events:40 errors:0 TX bytes:671 acl:0 sco:0 commands:35 errors:0 Features: 0xff 0xff 0x8d 0xfe 0x9b 0xf9 0x00 0x80 Packet type: DM1 DM3 DM5 DH1 DH3 DH5 HV1 HV2 HV3 Link policy: RSWITCH HOLD SNIFF PARK Link mode: SLAVE ACCEPT Name: 'ubuntu-0' Class: 0x4a0100 Service Classes: Networking, Capturing, Telephony Device Class: Computer, Uncategorized HCI Version: 2.0 (0x3) Revision: 0x4000 LMP Version: 2.0 (0x3) Subversion: 0x430e Manufacturer: Broadcom Corporation (15) Sorry for my English and thanks for any hints.

    Read the article

  • A terminal emulator for ex-Windows users

    - by Dan
    There are several things I would like to be better in Ubuntu Terminal Emulator. coloring, like in the source code Copy and paste keyboard shortcuts that I used all the time in Windows: Ctrl-C and Ctrl-V (Most of people here in Ubuntu use Ctrl+C and Ctrl+V keyboard shortcuts to copy and paste everywhere except the terminal! I think it's annoying for newcomers, and I don't worry about historical reasons) A feature to save all the output to log file UPDATE: Can the terminal be a powerful feature-full user-friendly tool like a modern IDE? The Linux user can spend 30% of time in the terminal. Programmers no longer code in a notepad. Can I see the history pane? Suggestions? Directory pane? Commands list? Search for words in an output? Contextual behavior? "Search in Google" for a mouse right-click. Tips and tricks learning? Time is money! Please, people, give me a link to the 21st - century terminal.

    Read the article

  • Routing tables don't show ppp0 after 12.04 kernel upgrade to 3.5.0: Haier CE682 modem configuration

    - by ubunsteve
    I'm trying to get my Haier CE682 EVDO modem, model number 201e:1022 to work in ubuntu 12.04 kernel 3.5.0-030500-generic #201207211835 . I had it working in a previous 12.04 kernel, using compat-wireless and these instructions http://zulkhamsyahmh.blogspot.com/2012/05/install-smartfren-haier-ce682-on-ubuntu.html, and to get it working had to edit the routing tables so that there was a ppp0 showing up, as suggested at http://www.linuxquestions.org/questions/slackware-14/wvdial-is-connecting-but-im-unable-to-do-anything-714861/ Network manager doesn't work with this modem, so I use either wvdial or gpppon to connect to it, both which work (after I run the command sudo modprobe usbserial vendor=0x201e product=0x1022 ) This is the output of when I connect with gpppon to the modem: Using interface ppp0 Connect: ppp0 <-- /dev/ttyUSB0 sent [LCP ConfReq id=0x1 ] rcvd [LCP ConfAck id=0x1 ] rcvd [LCP ConfReq id=0x2 ] sent [LCP ConfAck id=0x2 ] sent [LCP EchoReq id=0x0 magic=0x819c86db] rcvd [CHAP Challenge id=0x1 <1ac8f12799e953967a3cc222c9254690, name = ""] sent [CHAP Response id=0x1 <6f12a903dc40915ca2761c17b87f8fbd, name = "smart"] rcvd [LCP EchoRep id=0x0 magic=0x0] rcvd [CHAP Success id=0x1 ""] CHAP authentication succeeded CHAP authentication succeeded sent [CCP ConfReq id=0x1 ] sent [IPCP ConfReq id=0x1 ] rcvd [IPCP ConfReq id=0x1 ] sent [IPCP ConfAck id=0x1 ] rcvd [CCP ConfReq id=0x1] sent [CCP ConfAck id=0x1] rcvd [CCP ConfRej id=0x1 ] sent [CCP ConfReq id=0x2] rcvd [IPCP ConfRej id=0x1 ] sent [IPCP ConfReq id=0x2 ] rcvd [CCP ConfAck id=0x2] rcvd [IPCP ConfNak id=0x2 ] sent [IPCP ConfReq id=0x3 ] rcvd [IPCP ConfAck id=0x3 ] not replacing existing default route via 192.168.3.1 local IP address 10.191.248.154 remote IP address 10.17.95.25 primary DNS address 10.17.3.244 secondary DNS address 10.17.3.245 as you can see there is a problem with "not replacing existing default route via 192.168.3.1" This it the out put of route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default 192.168.3.1 0.0.0.0 UG 0 0 0 wlan0 link-local * 255.255.0.0 U 1000 0 0 wlan0 192.168.3.0 * 255.255.255.0 U 2 0 0 wlan0 I had tried these commands, which had previously worked in the earlier kernel: route del default route add default ppp0 but that broke my wireless internet connection. I then added the default routing as shown above with sudo route add default gw 192.168.3.1 wlan0 So it seems I need to add or change the routing to show a ppp0 connection, but I don't know how to do that.

    Read the article

  • Languages like Tcl that have configurable syntax?

    - by boost
    I'm looking for a language that will let me do what I could do with Clipper years ago, and which I can do with Tcl, namely add functionality in a way other than just adding functions. For example in Clipper/(x)Harbour there are commands #command, #translate, #xcommand and #xtranslate that allow things like this: #xcommand REPEAT; => DO WHILE .T. #xcommand UNTIL <cond>; => IF (<cond>); ;EXIT; ;ENDIF; ;ENDDO LOCAL n := 1 REPEAT n := n + 1 UNTIL n > 100 Similarly, in Tcl I'm doing proc process_range {_for_ project _from_ dat1 _to_ dat2 _by_ slice} { set fromDate [clock scan $dat1] set toDate [clock scan $dat2] if {$slice eq "day"} then {set incrementor [expr 24 * 60]} if {$slice eq "hour"} then {set incrementor 60} set method DateRange puts "Scanning from [clock format $fromDate -format "%c"] to [clock format $toDate -format "%c"] by $slice" for {set dateCursor $fromDate} {$dateCursor <= $toDate} {set dateCursor [clock add $dateCursor $incrementor minutes]} { # ... } } process_range for "client" from "2013-10-18 00:00" to "2013-10-20 23:59" by day Are there any other languages that permit this kind of, almost COBOL-esque, syntax modification? If you're wondering why I'm asking, it's for setting up stuff so that others with a not-as-geeky-as-I-am skillset can declare processing tasks.

    Read the article

  • Terminal closing itself after 14.04 upgrade

    - by David
    All was fine in 12.04, in this case I'm using virtualbox in Windows. Last days the warning message about my Ubuntu version no longer being supported was coming up pretty often, so, yesterday I finally decided to upgrade. The upgrading process ran ok, no errors, no warnings. After rebooting the errors started to happen. Just after booting up there were some errors about video, gnome, and video textures (sorry I didn't care in that moment so I don't remember well). Luckly that went away after installing VirtualBox additions. But the big problem here is that I can't use the terminal. It opens Ok when pressing control+alt+t, but most of the commands cause instant closing. For example, df, ls, mv, cd... usually work, although it has closed few times. But 'find' causes instant close. 'apt-get' update kills it too, just after it gets the package list from the sources, when it starts processing them. I've tried xterm, everything works and I have none of that problems. I have tried reinstalling konsole, bash-static, bash-completion, but nothing worked. I have no idea what to do as there is no error message to search for the cause. It seems something related to bash, but that's all I know.

    Read the article

  • Need to run a .sh as root on boot or login

    - by Graymayre
    Still new with linux and running ubuntu 12.10 I have a wireless stick (ae2500) which has known issues that has been partially solved using ndiswrapper. However, to use it I must run the same scripts every time I reboot, effectively uninstalling and reinstalling the driver. I made a .sh file to run every time to make it easy, but I must do the sudo login everytime. There are three solutions I am looking for and although not all are necessary to solve this particular problem, I would still like to know them all for learning purposes. run scripts or file.sh on boot (as well as other programs) run scripts or file.sh automatically with root privileges make the install permanent so as not to have to go through the process every time. Any additional information that can help me regarding this that I did not think to ask (including streamlining my commands), or general knowledge, would be greatly appreciated. Following are the contents of the file. I pretty much just made it as I would have entered it. cd ~/ndiswrapper-1.58rc1 sudo modprobe -rf ndiswrapper sudo rm /etc/modprobe.d/ndiswrapper.conf sudo rm -r /etc/ndiswrapper/* sudo depmod -a sudo make uninstall sudo make sudo make install sudo ndiswrapper -i bcmwlhigh5.inf ndiswrapper -l sudo modprobe ndiswrapper

    Read the article

  • Steps to send patch to Launchpad

    - by Alois Mahdal
    With a Git/Github background and knowing very little about Bazaar VCS, I would like to occasionally report a bug to Launchpad and even send a patch. I'd like to do it in a "proper" way so that it's ready for merging or improvement while not getting in way. I can't seem to find a decent simple How-to suited for my needs. So what I did so far: I have created a Launchpad account, reported the bug, installed Bazaar and setup SSH keys etc. Now if it was Github, I'd fork the repo, clone the forked repo, create a sanely named branch and do the work, commit + push, create a pull request using Github WUI. But it's not Github, and both LP and Bazaar architectures seem quite different from their Github/Git cunterparts. So could a kind soul save me from drowning in tons of documents and complile a straightforward step path, mainly the second part? Possibly including relevant CLI commands when they are needed? Edit: It seems that I should clarify if I'm asking specifically about Ubuntu packages (whatever it means) or Launchpad packages. I don't really care much about distinction between Ubuntu packages and non-Ubuntu packages. Any software could be in Ubuntu today and out of it tomorrow, or vice-versa. The development is what matters much more than distribution. Ao I was assuming that not every single package distributed in Ubuntu is hosted on Launchpad, an "official" or "default" workflow for Launchpad exists (well if all devs can agree on using Bazaar, why couldn't most of them agree on a patching workflow?), so I'm asking about the Launchpad way, not the Ubuntu way. And I chose AU because since the intersection is vast, I guess it's pretty on topic here.

    Read the article

  • ALPS touchpad stops working after reboot

    - by user58289
    I recently upgraded to 12.04 LTS. My Compaq Presario CQ-40 324la touchpad worked after first restarting after installation. But after restarting a second time, the touchpad is completely disabled, without having changed anything in the system. I've tried solutions but haven't had good results. The applications I've installed (fro "solutions" are: Pointing Devices Synaptiks Dconf-Tools I've also tried updating GRUB, adding this line: GRUB_CMDLINE_LINUX_DEFAULT="quiet splash i8042.nomux") I tried these commands in a terminal. Neither has worked. sudo modprobe -r psmouse sudo modprobe psmouse proto=imps El Touchpad ALPS se desactiva al reiniciar Recién he actualizado a Ubuntu 12.04LTS y a mi parecer ha mejorado mucho con respecto a 11.10... Pero ese no es mi punto ahora. El Touchpad funcionó correctamente luego del primer reinicio después de la instalación. Pero luego de volver a reiniciar, el Touchpad queda totalmente deshabilitado sin haber hecho cambio alguno en el sistema. He probado las soluciones en su mayoría y no he tenido buenos resultados. Las aplicaciones que he instalado (de las "soluciones") son: -Dispositivos apuntadores. -Synaptiks -DConf-Tools Y he intentado también actualizando el grub (añadiéndole una linea así: GRUB_CMDLINE_LINUX_DEFAULT="quiet splash i8042.nomux") Intenté en la terminal con el comando: sudo modprobe -r psmouse sudo modprobe psmouse proto=imps Ninguno me ha resultado bien. La laptop es Compaq Presario CQ-40 324la

    Read the article

< Previous Page | 233 234 235 236 237 238 239 240 241 242 243 244  | Next Page >