Search Results

Search found 6427 results on 258 pages for 'customer protection'.

Page 238/258 | < Previous Page | 234 235 236 237 238 239 240 241 242 243 244 245  | Next Page >

• VPN Connection causes DNS to use wrong DNS server

  - by Bryan

  I have a Windows 7 PC on our company network (which is a member of our Active Directory). Everything works fine until I open a VPN connection to a customer's site. When I do connect, I lose network access to shares on the network, including directories such as 'Application Data' that we have a folder redirection policy for. As you can imagine, this makes working on the PC very difficult, as desktop shortcuts stop working, software stops working properly due to having 'Application Data' pulled from under it. Our network is routed (10.58.5.0/24), with other local subnets existing within the scope of 10.58.0.0/16. The remote network is on 192.168.0.0/24. I've tracked the issue down to being DNS related. As soon as I open the VPN tunnel, all my DNS traffic goes via the remote network, which explains the loss of local resources, but my question is, how can I force local DNS queries to go to our local DNS servers rather than our customers? The output of ipconfig /all when not connected to the VPN is below: Windows IP Configuration Host Name . . . . . . . . . . . . : 7k5xy4j Primary Dns Suffix . . . . . . . : mydomain.local Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : mydomain.local Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : mydomain.local Description . . . . . . . . . . . : Broadcom NetLink (TM) Gigabit Ethernet Physical Address. . . . . . . . . : F0-4D-A2-DB-3B-CA DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::9457:c5e0:6f10:b298%10(Preferred) IPv4 Address. . . . . . . . . . . : 10.58.5.89(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : 31 January 2012 15:55:47 Lease Expires . . . . . . . . . . : 10 February 2012 10:11:30 Default Gateway . . . . . . . . . : 10.58.5.1 DHCP Server . . . . . . . . . . . : 10.58.3.32 DHCPv6 IAID . . . . . . . . . . . : 250629538 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-14-AC-76-2D-F0-4D-A2-DB-3B-CA DNS Servers . . . . . . . . . . . : 10.58.3.32 10.58.3.33 NetBIOS over Tcpip. . . . . . . . : Enabled This is the output of the same command with the VPN tunnel connected: Windows IP Configuration Host Name . . . . . . . . . . . . : 7k5xy4j Primary Dns Suffix . . . . . . . : mydomain.local Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : mydomain.local PPP adapter Customer Domain: Connection-specific DNS Suffix . : customerdomain.com Description . . . . . . . . . . . : CustomerDomain Physical Address. . . . . . . . . : DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 192.168.0.85(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.255 Default Gateway . . . . . . . . . : DNS Servers . . . . . . . . . . . : 192.168.0.16 192.168.0.17 Primary WINS Server . . . . . . . : 192.168.0.17 NetBIOS over Tcpip. . . . . . . . : Disabled Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : mydomain.local Description . . . . . . . . . . . : Broadcom NetLink (TM) Gigabit Ethernet Physical Address. . . . . . . . . : F0-4D-A2-DB-3B-CA DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::9457:c5e0:6f10:b298%10(Preferred) IPv4 Address. . . . . . . . . . . : 10.58.5.89(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : 31 January 2012 15:55:47 Lease Expires . . . . . . . . . . : 10 February 2012 10:11:30 Default Gateway . . . . . . . . . : 10.58.5.1 DHCP Server . . . . . . . . . . . : 10.58.3.32 DHCPv6 IAID . . . . . . . . . . . : 250629538 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-14-AC-76-2D-F0-4D-A2-DB-3B-CA DNS Servers . . . . . . . . . . . : 10.58.3.32 10.58.3.33 NetBIOS over Tcpip. . . . . . . . : Enabled Routing table Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.58.5.1 10.58.5.89 20 10.58.5.0 255.255.255.0 On-link 10.58.5.89 276 10.58.5.89 255.255.255.255 On-link 10.58.5.89 276 10.58.5.255 255.255.255.255 On-link 10.58.5.89 276 91.194.153.42 255.255.255.255 10.58.5.1 10.58.5.89 21 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.0.0 255.255.255.0 192.168.0.95 192.168.0.85 21 192.168.0.85 255.255.255.255 On-link 192.168.0.85 276 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 10.58.5.89 276 224.0.0.0 240.0.0.0 On-link 192.168.0.85 276 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 10.58.5.89 276 255.255.255.255 255.255.255.255 On-link 192.168.0.85 276 The binding order for the interfaces is as follows: I've not configured the VPN tunnel to use the default gateway at the remote end, and network comms to nodes on both networks are fine. (i.e. I can ping any node on our network or the remote network). I've modified the PPTP connection properties to use the DNS servers 10.58.3.32 followed by 192.168.0.16, yet the query still goes to 192.168.0.16. Edit: The local resources that disappear are hosted on domain DFS roots, which might (or might not) be relevant.

  Read the article

• Flickering issue in external monitor when used with Acer Aspire One D260 netbook (Intel GMA 3150)

  - by seyenne

  I recently purchased a Acer netbook, Aspire One D260. It runs flawlessly. Yesterday I bought a Samsung 23" TFT with a native resolution of 1920x1080. According to the information found in the internet and my local computer dealer, the Intel chipset can handle the native resolution of the monitor. However, this is only partly the case. I use the VGA cable to connect, the monitor instantly switches to the native resolution and now the problem: Occasionally, especially the first 2 hours after booting up, I have a flickering all over the screen, sometimes the entire screen is shaking and spinning around like crazy. I figured out that lowering the resolution avoids the flicker but this helps only for some time. I can rule out that it's the monitor's problem since I found no issues with another notebook. Right now, I have no problems with the netbook, for about 30 minutes I didn't experience any issues... But I don't know for how long, it occurs without warning :-) I'm worried that if I would bring the netbook back to the dealer and explain my problem, after testing it on an external screen in the local shop, everything works just fine... And I won't get helped with the problem because I can't prove it. (I'm currently in Thailand and over here, customer service is nothing like back home in Germany) What can I do? Is this a driver related issue? (I installed the latest GPU driver) Is it because of the VGA cable? (But why does it work sometimes without any problems and with no issues on the other notebook) I monitored the GPU/CPU temperature, nothing changes really over time.. Can it simply be a faulty GPU and is a replacement justifiable? I'm really stressed now because for the time I'm writing, the flickering didn't occur... but for sure, soon or later it will happen again.. I forgot to mention, the problem also happens if the netbook runs on battery, unplugged. So the only hardware that is plugged is the TFT screen. ...........and here it comes again, flickering has just begun. NEED HELP! Thank you all for reading through this and giving any suggestions if possible. Cheers

  Read the article

• Email delivery management grievances

  - by joxl

  The question I have may be more of principle than anything else, but here's my dilemma. I manage an email system for a small company (about 20 email users). We own a plain-letter .com domain name through Network Solutions. Our email service is hosted by Google Apps. Recently (Feb. 2011) we've been having customers report that they aren't getting our emails. Upon further investigation it seems that the failed emails are all to a common (well known) domain. We have not received any bounce messages for the emails. We've also contacted a few of the intended recipients, who have reported that the messages are not in their spam box; they simply did not receive anything. In these cases we re-sent the same email to an alternate address on another domain, which was successful received. One customer contacted their email provider about the issue. The provider recommended that we submit a form to be white-listed by their domain. Here's where my problem begins. I feel like this is heading down a slippery slope. Doesn't this undermine the very principle of email? If this is the appropriate action to take in these situations where will it end? In theory (following this model) it could be argued that eventually one will first need to "whitelist" (or more appropriately termed "authenticate") themselves with an email host before actually sending any messages. More to this point, what keeps the "bad" spammers from doing the same thing...? We've just gone full circle. I know avoiding anti-spam measures is a big cat-and-mouse game, but I think this is the wrong way of "patching" the problem. Email standards say that messages should not just disappear silently. I have a problem supporting a model that says "you must do < this to make sure your emails aren't ignored". I have a notion to call the provider and voice my complaint, although I have a feeling it will probably fall on deaf ears. Am I missing something here? Is this an acceptable approach to email spam problems? What should I do?

  Read the article

• Can't send email through Comcast SMTP to my domains

  - by Midnight Oil

  I am a Comcast customer with 3 computers and 3 computer users in the house. There are 2 fully updated Macs and one PC running Windows 7. We use Mail on the Macs, and Outlook on Windows 7. All computer accounts are configured to send mail through port 587 of smtp.comcast.net. I also have two personal domains registered with Network Solutions. For the sake of this discussion, call my domains myOwnDomain1.com and myOwnDomain2.com. I have email addresses at both domains. They are of the form [email protected] and [email protected]. Until recently, our email worked as expected. However, sometime between September 13, 2012 and September 19, 2012, we lost the ability to send email through Comcast's SMTP server to the email addresses at my personal domains. If we attempt to send email through Comcast's SMTP to those addresses, the email never arrives. Furthermore, the email clients give no indication of failure. The email just never arrives. The result is the same on all 3 computers and with all accounts on those computers. We can successfully send email through Comcast's SMTP from any of our accounts on any of our computers to any email address other than to my email addresses at my personal domains! However, I receive email at those domains that is not sent through smtp.comcast.net. For example, I can successfully send email from my gmail and yahoo accounts to my email addresses at my personal domains. Furthermore, I can successfully send email through smtp.myOwnDomain1.com to [email protected] and through smtp.myOwnDoman2.com to [email protected]. Comcast says the problem must be at Network Solutions. According to Network Solutions, their logs show they are not blocking reception of the email, and our IP address is not flagged as a spam source. They say the email is simply not arriving. Does anyone have any ideas why we can't send email through Comcast's SMTP server to my domains? As an odd coincidence, we recently noticed a change in Comcast's SMTP service. there is now a 5 minute delay on all outbound mail. Comcast's SMTP server seems to sit on the mail with a 5 minute timer.

  Read the article

• Small Business Server services will not start, and remote desktop and UAC are broken

  - by Stephen Jennings

  Yesterday I began setting up a server with Windows Small Business Server 2008. All I am configuring it for right now is to be a domain controller and Exchange server. I completed the initial setup of SBS then started looking through different connection options (allowing VPN versus using a TS Gateway). After I rebooted one time, I started having three not-obviously-related issues: First, I could no longer remote desktop into the computer. I ran TCPView and saw that it was no longer listening on port 3389. I checked everything in Terminal Service Configuration but everything shows the computer ought to be allowing connections. Also, when I tried to use anything that required user account control elevation, the UAC dialog never popped up and the program that was waiting just froze. If I try to run "regedit" from the Run box, for example, it never appears. When I run in safe mode which does not run with UAC, I was able to access everything. I didn't want to deal with it, so I turned off UAC and rebooted. Finally, in the Windows SBS Console, there are status indicators for Security, Updates, Backup, and Other Alerts. The first three get stuck saying "Querying". Looking in the computer alerts, I have events showing the following services stopped: Background Intelligent Transfer Service KtmRm for Distributed Transaction Coordinator Distributed Transaction Coordinator Microsoft Exchange Information Store Microsoft Exchange System Attendant Microsoft Exchange Transport Windows Remote Management Update Services Windows Update I figured I must have configured something wrong accidentally and I couldn't find anything using Google explaining what might be the case, so I just decided to format the hard drive and reinstall SBS from scratch. I did this and everything was working last night, but I just turned the machine back on and it is doing the same thing again! On my second install, I did not configure anything except the following (all from SBS Console): Connect to the Internet (set IP and router address) Turn off customer feedback. Set up internet address. Decline to use a Smart Host for email. Added one standard user account. Since this happened again and I was very careful the second time not to configure anything outside of the SBS Console, I feel like there's something else going on. Right now the machine is on an isolated network that does have internet access. My desktop is the only other machine plugged into this network. Any and all help is appreciated (before I tear my hair out!)

  Read the article

• Secret, unlogged, transparent, case-sensitive proxy in IIS6?

  - by Ian Boyd

  Does IIS have a secret, unlogged, transparent, case-sensitive proxy built into it? A file exists on the web-server: GET http://www.stackoverflow.com/javascript/ModifyQuoteArea.js HTTP/1.1 Accept: text/html, application/xhtml+xml, */* Accept-Language: en-US User-Agent: Mozilla/5.0 (compatible; MSIE 9.0; Windows NT 6.1; WOW64; Trident/5.0) Accept-Encoding: gzip, deflate Connection: Keep-Alive Host: www.stackoverflow.com HTTP/1.1 200 OK Connection: Keep-Alive Content-Length: 29246 Date: Mon, 07 Mar 2011 14:20:07 GMT Content-Type: application/x-javascript ETag: "5a0a6178edacb1:1c51" Server: Microsoft-IIS/6.0 Last-Modified: Fri, 02 Tue 2010 17:03:32 GMT Accept-Ranges: bytes X-Powered-By: ASP.NET ... Problem is that a changes made to the file will not get served, the old (i.e. February of last year) version keeps getting served: HTTP/1.1 200 OK Connection: Keep-Alive Content-Length: 29246 Date: Mon, 07 Mar 2011 14:23:07 GMT Content-Type: application/x-javascript ETag: "5a0a6178edacb1:1c51" Server: Microsoft-IIS/6.0 Last-Modified: Fri, 02 Tue 2010 17:03:32 GMT Accept-Ranges: bytes X-Powered-By: ASP.NET ... The same old file gets served, even though we've: renamed the file deleted the file restarted IIS The request for this file does not appear in the IIS logs (e.g. C:\WINNT\System32\LogFiles\W3SVC7\) And this only happens from the outside (i.e. the internet). If you issue the request locally on the server, then you will: - get the current file (file there) - 404 (file renamed) - 404 (file deleted) But if i change the case of the requested resource, i.e.: GET http://www.stackoverflow.com/javascript/MoDiFyQuOtEArEa.js HTTP/1.1 Accept: text/html, application/xhtml+xml, */* Accept-Language: en-US User-Agent: Mozilla/5.0 (compatible; MSIE 9.0; Windows NT 6.1; WOW64; Trident/5.0) Accept-Encoding: gzip, deflate Connection: Keep-Alive Host: www.stackoverflow.com Note: MoDiFyQuOtEArEa.js verses ModifyQuoteArea.js Then i do get the proper file (or get the 404 as i expect if the file is renamed or deleted). But any subsequent changes to the file will not show up until i change the case of the file i'm asking for. Checking the IIS logs all indicate that the (internet) requests are all coming the correct client on the internet (i.e. not from some intermediate proxy). Since the file doesn't exist on the hard drive anymore, i conclude that there is a proxy. The requests serviced from this proxy are not logged in the IIS logs. The requests for new files are logged, and from the client IP, not a proxy IP. The proxy is case sensitivie. This does not sound like something Microsoft, or IIS, would do: - a transparent proxy - case-sensitivie - unlogged - surviving restarts of IIS - surviving in a cache for hours i can't believe that our customer's IIS is doing these things. i'm assuming there is some other transparent proxy in front of IIS. Or, does IIS have a transparent, unlogged, case-sensitive, memory based, proxy, that caches content for at least 7 hours? (Come Monday morning, IIS is serving the correct file, unlogged).

  Read the article

• VFS: file-max limit 1231582 reached

  - by Rick Koshi

  I'm running a Linux 2.6.36 kernel, and I'm seeing some random errors. Things like ls: error while loading shared libraries: libpthread.so.0: cannot open shared object file: Error 23 Yes, my system can't consistently run an 'ls' command. :( I note several errors in my dmesg output: # dmesg | tail [2808967.543203] EXT4-fs (sda3): re-mounted. Opts: (null) [2837776.220605] xv[14450] general protection ip:7f20c20c6ac6 sp:7fff3641b368 error:0 in libpng14.so.14.4.0[7f20c20a9000+29000] [4931344.685302] EXT4-fs (md16): re-mounted. Opts: (null) [4982666.631444] VFS: file-max limit 1231582 reached [4982666.764240] VFS: file-max limit 1231582 reached [4982767.360574] VFS: file-max limit 1231582 reached [4982901.904628] VFS: file-max limit 1231582 reached [4982964.930556] VFS: file-max limit 1231582 reached [4982966.352170] VFS: file-max limit 1231582 reached [4982966.649195] top[31095]: segfault at 14 ip 00007fd6ace42700 sp 00007fff20746530 error 6 in libproc-3.2.8.so[7fd6ace3b000+e000] Obviously, the file-max errors look suspicious, being clustered together and recent. # cat /proc/sys/fs/file-max 1231582 # cat /proc/sys/fs/file-nr 1231712 0 1231582 That also looks a bit odd to me, but the thing is, there's no way I have 1.2 million files open on this system. I'm the only one using it, and it's not visible to anyone outside the local network. # lsof | wc 16046 148253 1882901 # ps -ef | wc 574 6104 44260 I saw some documentation saying: file-max & file-nr: The kernel allocates file handles dynamically, but as yet it doesn't free them again. The value in file-max denotes the maximum number of file- handles that the Linux kernel will allocate. When you get lots of error messages about running out of file handles, you might want to increase this limit. Historically, the three values in file-nr denoted the number of allocated file handles, the number of allocated but unused file handles, and the maximum number of file handles. Linux 2.6 always reports 0 as the number of free file handles -- this is not an error, it just means that the number of allocated file handles exactly matches the number of used file handles. Attempts to allocate more file descriptors than file-max are reported with printk, look for "VFS: file-max limit reached". My first reading of this is that the kernel basically has a built-in file descriptor leak, but I find that very hard to believe. It would imply that any system in active use needs to be rebooted every so often to free up the file descriptors. As I said, I can't believe this would be true, since it's normal to me to have Linux systems stay up for months (even years) at a time. On the other hand, I also can't believe that my nearly-idle system is holding over a million files open. Does anyone have any ideas, either for fixes or further diagnosis? I could, of course, just reboot the system, but I don't want this to be a recurring problem every few weeks. As a stopgap measure, I've quit Firefox, which was accounting for almost 2000 lines of lsof output (!) even though I only had one window open, and now I can run 'ls' again, but I doubt that will fix the problem for long. (edit: Oops, spoke too soon. By the time I finished typing out this question, the symptom was/is back) Thanks in advance for any help. And another update: My system was basically unusable, so I decided I had no option but to reboot. But before I did, I carefully quit one process at a time, checking /proc/sys/fs/file-nr after each termination. I found that, predictably, the number of open files gradually went down as I closed things down. Unfortunately, it wasn't a large effect. Yes, I was able to clear up 5000-10000 open files, but there were still over 1.2 million left. I shut down just about everything. All interactive shells, except for the one ssh I left open to finish closing down, httpd, even nfs service. Basically everything in the process table that wasn't a kernel process, and there were still an appalling number of files apparently left open. After the reboot, I found that /proc/sys/fs/file-nr showed about 2000 files open, which is much more reasonable. Starting up 2 Xvnc sessions as usual, along with the dozen or so monitoring windows I like to keep open, brought the total up to about 4000 files. I can see nothing wrong with that, of course, but I've obviously failed to identify the root cause. I'm still looking for ideas, since I definitely expect it to happen again. And another update, the next day: I watched the system carefully, and discovered that /proc/sys/fs/file-nr showed a growth of about 900 open files per hour. I shut down the system's only NFS client for the night, and the growth stopped. Mind you, it didn't free up the resources, but it did at least stop consuming more. Is this a known bug with NFS? I'll be bringing the NFS client back online today, and I'll narrow it down further. If anyone is familiar with this behavior, feel free to jump in with "Yeah, NFS4 has this problem, go back to NFS3" or something like that.

  Read the article

• Adobe Reader not loading form content

  - by wullxz

  We have an FDL file which is used to offer an online application possibility. The FDL is filled out and sent to a mailbox. When I open the received file, Adobe Reader starts, loads the document in Internet Explorer (had to change my default browser because it doesn't work in chrome - the customer uses IE as default) and displays a warning that Adobe Reader has blocked the connection to the server where the initial document is saved: I can then click on "Trust this document once" (translated by me!) or "Add this host to trusted hosts" (also translated by me!). The second option doesn't work at all. The first option works but is a little bit annoying. I looked into Adobe Readers options (Edit - "Voreinstellungen" in german / the last option - Security (advanced)) and found the possibility to add hosts, files and directories or allow Adobe Reader to use the "Trusted Websites" list from Internetoptions. When I add the website either to Trusted Websites or the trusted list in Adobe Readers options, the warning doesn't pop up but the content in the prefilled (by the applicant) input boxes of the document doesn't show up on Windows 7 but it does show up on Windows XP. This Screenshot shows the settings window described in the last paragraph. The big input box at the bottom normally holds the trusted files/directories/hosts list. System Information: Windows 7 Enterprise x64 Adobe Reader X multiple IE versions (mine is latest but there's also IE 7 or 8) How do I get Adobe Reader to load the content of the form? This behaviour can be reproduced on a PC. When opening an fdf from a command line the form fields are blank even though there is data in the fdf and the pdf is located in a mnaully entered trsuted folder. Steps to reproduce: Clean install a Windows 7 PC (or use a virtual box) Map a network drive to a shared folder with a subfolder e.g. c:\test\docs becomes m:\docs Set security permissions to allow full control to everyone Add an fdf and a matching pdf file in the subfolder Manually add m:\docs to each of the trusted folders in the trust manager registry settings Ensure that Enhanced Security is on Run a command line to open the fdf file Expected result: pdf is opened in Adobe Reader with form fields filled out with data Actual results: pdf is opened with blank fields 'Yellow bar' appears asking to add document to trusted locations It appears that Adobe Reader XI is ignoring the privileged locations entries in the registry. Adding the document via the 'yellow bar' adds the individual document, with the same folder, to the privileged locations but means that the process has to be repeated for every document that needs to be opened from the folder.

  Read the article

• Problems migrating an EBS backed instance over AWS Regions

  - by gshankar

  Note: I asked this question on the EC2 forums too but haven't received any love there. Hopefully the ServerFault community will be more awesome. The new AWS Sydney region opening up is something that we've been waiting for for a long time but I'm having a lot of trouble migrating our instances over from N. California. I managed to migrate 1 instance over using CloudyScripts to move a snapshot and then firing up a new instance in the Sydney region. This was a very new instance so both the source and destination were running on a Ubuntu 12.04 LTS server and I had no issues there. However, the rest of our instances are all Ubuntu 10.04 LTS and with these, I'm having a lot of problems. I've tried following: 1- following the AWS whitepaper on moving instances which was given to us at the recent Customer Appreciation Day in Sydney where the new region was launched. The problem with this approach was with the last step (Step 19) here you register the image: ec2-register -s snap-0f62ec3f -n "Wombat" -d "migrated Wombat" --region ap-southeast-2 -a x86_64 --kernel aki-937e2ed6 --block-device-mapping "/dev/sdk=ephemeral0" I keep getting this error: Client.InvalidAMIID.NotFound: The AMI ID 'ami-937e2ed6' does not exist which I think is due to the kernel_id not existing in the Sydney region? 2- Using CloudyScripts to move a snapshot and then creating a new volume and attaching to a new instance in Sydney This results in the instance just hanging on boot and failing the status checks. I can't SSH in or look at the server log I suspect that my issue is with finding the right kernel_id for the volume in the new region. However I can't seem to work out how to go about finding this kernel_id, the ones I've tried (from the original instance) don't result in the Client.InvalidAMIID.NotFound: The AMI ID 'ami-937e2ed6' error and any other kernel_id just won't boot. I've tried both 12.04 and 10.04 versions of Ubuntu. Nothing seems to work, I've been banging my head against a wall for a while now, please help! New (broken) instance i-a1acda9b ami-9b8611a1 aki-31990e0b Source instance i-08a6664e ami-b37e2ef6 aki-937e2ed6 p.s. I also tried following this guide on updating my Ubuntu LTS version to 12.04 before doing the migration but it didn't seem to work either, still getting stuck on updating the kernel_id http://ubuntu-smoser.blogspot.com.au/2010/04/upgrading-ebs-instance.html

  Read the article

• RFC 1918 address on open internet?

  - by longneck

  In trying to diagnose a failover problem with my Cisco ASA 5520 firewalls, I ran a traceroute to www.btfl.com and, much to my surprise, some of the hops came back as RFC 1918 addresses. Just to be clear, this host is not behind my firewall and there is no VPN involved. I have to connect across the open internet to get there. How/why is this possible? asa# traceroute www.btfl.com Tracing the route to 157.56.176.94 1 <redacted> 2 <redacted> 3 <redacted> 4 <redacted> 5 nap-edge-04.inet.qwest.net (67.14.29.170) 0 msec 10 msec 10 msec 6 65.122.166.30 0 msec 0 msec 10 msec 7 207.46.34.23 10 msec 0 msec 10 msec 8 * * * 9 207.46.37.235 30 msec 30 msec 50 msec 10 10.22.112.221 30 msec 10.22.112.219 30 msec 10.22.112.223 30 msec 11 10.175.9.193 30 msec 30 msec 10.175.9.67 30 msec 12 100.94.68.79 40 msec 100.94.70.79 30 msec 100.94.71.73 30 msec 13 100.94.80.39 30 msec 100.94.80.205 40 msec 100.94.80.137 40 msec 14 10.215.80.2 30 msec 10.215.68.16 30 msec 10.175.244.2 30 msec 15 * * * 16 * * * 17 * * * and it does the same thing from my FiOS connection at home: C:\>tracert www.btfl.com Tracing route to www.btfl.com [157.56.176.94] over a maximum of 30 hops: 1 1 ms <1 ms <1 ms myrouter.home [192.168.1.1] 2 8 ms 7 ms 8 ms <redacted> 3 10 ms 13 ms 11 ms <redacted> 4 12 ms 10 ms 10 ms ae2-0.TPA01-BB-RTR2.verizon-gni.net [130.81.199.82] 5 16 ms 16 ms 15 ms 0.ae4.XL2.MIA19.ALTER.NET [152.63.8.117] 6 14 ms 16 ms 16 ms 0.xe-11-0-0.GW1.MIA19.ALTER.NET [152.63.85.94] 7 19 ms 16 ms 16 ms microsoft-gw.customer.alter.net [63.65.188.170] 8 27 ms 33 ms * ge-5-3-0-0.ash-64cb-1a.ntwk.msn.net [207.46.46.177] 9 * * * Request timed out. 10 44 ms 43 ms 43 ms 207.46.37.235 11 42 ms 41 ms 40 ms 10.22.112.225 12 42 ms 43 ms 43 ms 10.175.9.1 13 42 ms 41 ms 42 ms 100.94.68.79 14 40 ms 40 ms 41 ms 100.94.80.193 15 * * * Request timed out.

  Read the article

• Cisco ASA SSL VPN options?

  - by JonH

  Disclaimer: I am not a network admin so I may be wrong here but I thought asking here would help. I'm a developer mainly on the .net framework as well as helping get a mobile intranet app working. Because this app is only allowed to be used on our network I can easily run this app on our wireless network connection within our building. All is fine and dandy but we'd also like to be able to run this mobile app at say a customer plant using VPN software. I thought surely this could be easy as we exclusively use Samsung s4 phones so I thought I'd download Cisco's Samsung any connect software to allow us to VPN...its right on the play store. Sure enough it doesn't work. I mention it to our network admin who says not possible since we have old technology that doesn't support SSL. He mentions we'd have to upgrade all of our hardware, the firewall, etc. to get this to work. We really need VPN on our phones not only for this app but other internal apps, etc. He did mention the following: We can’t upgrade the software on our ASA, because we don’t have enough memory for the new version.  (the asa is very old).  We can’t add more memory, so we would have to get a new firewall, which I have been told I cannot do. In addition he also mentioned: The Samsung AnyConnect client uses SSL to connect.  With the current (old) version of software that our firewall is running, the SSL connections are unreliable.  We need different hardware in order to upgrade our firewall, which we are unable to attain at this time.  This is the same reason that Windows 8 clients are not able to connect. I am curious hence me asking. vpns seem to be fairly simple to setup. What other options do I have aside from making this a public site or web service that consumes this data over the internet as this is a complete no no. What can we do to make this work without that much effort or cost.

  Read the article

• FFmpeg creates emtpy (black) frames

  - by resamsel

  I have a set of images from a timelapse shot (172 JPG files) that I want to convert into a movie. I tried several parameters with FFmpeg, but all I get is a video with black frames (though it has the expected length). ffmpeg -f image2 -vcodec mjpeg -y -i img_%03d.jpg timelapse2.mpg The command above creates this video: http://sdm-net.org/data/timelapse2.mpg What I'm expecting is something like this (created with Time Lapse Assembler.app): https://vimeo.com/39038362 - This is my fallback option, but I'd really like to create timelapse movies from a script. I'm on OSX Lion (10.7.3) with FFmpeg version (0.10) installed via Homebrew. I also tried to find a proper version of mencoder for OSX, but this doesn't seem to be an easy task. Also, ImageMagick's convert doesn't seem to work nicely, it creates really bad output and it seems there's not much I can do about it... Edit: With libx264 and an mp4 container: ffmpeg -f image2 -y -i img_%03d.jpg -vcodec libx264 timelapse4.mp4 Output: ffmpeg version 0.10 Copyright (c) 2000-2012 the FFmpeg developers built on Mar 26 2012 13:47:02 with clang 3.0 (tags/Apple/clang-211.12) configuration: --prefix=/usr/local/Cellar/ffmpeg/0.10 --enable-shared --enable-gpl --enable-version3 --enable-nonfree --enable-hardcoded-tables --enable-libfreetype --cc=/usr/bin/clang --enable-libx264 --enable-libfaac --enable-libmp3lame --enable-librtmp --enable-libtheora --enable-libvorbis --enable-libvpx --enable-libxvid --enable-libopencore-amrnb --enable-libopencore-amrwb --enable-libass --disable-ffplay libavutil 51. 34.101 / 51. 34.101 libavcodec 53. 60.100 / 53. 60.100 libavformat 53. 31.100 / 53. 31.100 libavdevice 53. 4.100 / 53. 4.100 libavfilter 2. 60.100 / 2. 60.100 libswscale 2. 1.100 / 2. 1.100 libswresample 0. 6.100 / 0. 6.100 libpostproc 52. 0.100 / 52. 0.100 Input #0, image2, from 'img_%03d.jpg': Duration: 00:00:06.88, start: 0.000000, bitrate: N/A Stream #0:0: Video: mjpeg, yuvj420p, 3888x2592 [SAR 72:72 DAR 3:2], 25 fps, 25 tbr, 25 tbn, 25 tbc [buffer @ 0x7f8ec9415f20] w:3888 h:2592 pixfmt:yuvj420p tb:1/1000000 sar:72/72 sws_param: [libx264 @ 0x7f8ec981d800] using SAR=1/1 [libx264 @ 0x7f8ec981d800] frame MB size (243x162) > level limit (36864) [libx264 @ 0x7f8ec981d800] MB rate (984150) > level limit (983040) [libx264 @ 0x7f8ec981d800] using cpu capabilities: MMX2 SSE2Fast SSSE3 FastShuffle SSE4.2 AVX [libx264 @ 0x7f8ec981d800] profile High, level 5.1 [libx264 @ 0x7f8ec981d800] 264 - core 120 - H.264/MPEG-4 AVC codec - Copyleft 2003-2011 - http://www.videolan.org/x264.html - options: cabac=1 ref=3 deblock=1:0:0 analyse=0x3:0x113 me=hex subme=7 psy=1 psy_rd=1.00:0.00 mixed_ref=1 me_range=16 chroma_me=1 trellis=1 8x8dct=1 cqm=0 deadzone=21,11 fast_pskip=1 chroma_qp_offset=-2 threads=12 sliced_threads=0 nr=0 decimate=1 interlaced=0 bluray_compat=0 constrained_intra=0 bframes=3 b_pyramid=2 b_adapt=1 b_bias=0 direct=1 weightb=1 open_gop=0 weightp=2 keyint=250 keyint_min=25 scenecut=40 intra_refresh=0 rc_lookahead=40 rc=crf mbtree=1 crf=23.0 qcomp=0.60 qpmin=0 qpmax=69 qpstep=4 ip_ratio=1.40 aq=1:1.00 Output #0, mp4, to 'timelapse4.mp4': Metadata: encoder : Lavf53.31.100 Stream #0:0: Video: h264 (![0][0][0] / 0x0021), yuvj420p, 3888x2592 [SAR 72:72 DAR 3:2], q=-1--1, 25 tbn, 25 tbc Stream mapping: Stream #0:0 -> #0:0 (mjpeg -> libx264) Press [q] to stop, [?] for help frame= 172 fps= 18 q=-1.0 Lsize= 259kB time=00:00:06.80 bitrate= 312.3kbits/s video:256kB audio:0kB global headers:0kB muxing overhead 1.089647% [libx264 @ 0x7f8ec981d800] frame I:1 Avg QP: 9.60 size:212820 [libx264 @ 0x7f8ec981d800] frame P:43 Avg QP:30.50 size: 291 [libx264 @ 0x7f8ec981d800] frame B:128 Avg QP:31.00 size: 285 [libx264 @ 0x7f8ec981d800] consecutive B-frames: 0.6% 0.0% 1.7% 97.7% [libx264 @ 0x7f8ec981d800] mb I I16..4: 22.5% 77.2% 0.3% [libx264 @ 0x7f8ec981d800] mb P I16..4: 0.0% 0.0% 0.0% P16..4: 0.0% 0.0% 0.0% 0.0% 0.0% skip:100.0% [libx264 @ 0x7f8ec981d800] mb B I16..4: 0.0% 0.0% 0.0% B16..8: 0.0% 0.0% 0.0% direct: 0.0% skip:100.0% L0: 1.2% L1:98.8% BI: 0.0% [libx264 @ 0x7f8ec981d800] 8x8 transform intra:77.2% inter:100.0% [libx264 @ 0x7f8ec981d800] coded y,uvDC,uvAC intra: 41.2% 23.4% 0.6% inter: 0.0% 0.0% 0.0% [libx264 @ 0x7f8ec981d800] i16 v,h,dc,p: 40% 25% 35% 1% [libx264 @ 0x7f8ec981d800] i8 v,h,dc,ddl,ddr,vr,hd,vl,hu: 36% 32% 30% 1% 0% 0% 0% 0% 0% [libx264 @ 0x7f8ec981d800] i4 v,h,dc,ddl,ddr,vr,hd,vl,hu: 51% 40% 6% 1% 1% 0% 1% 0% 1% [libx264 @ 0x7f8ec981d800] i8c dc,h,v,p: 60% 21% 19% 0% [libx264 @ 0x7f8ec981d800] Weighted P-Frames: Y:0.0% UV:0.0% [libx264 @ 0x7f8ec981d800] ref P L0: 92.3% 0.0% 0.0% 7.7% [libx264 @ 0x7f8ec981d800] ref B L0: 50.0% 0.0% 50.0% [libx264 @ 0x7f8ec981d800] ref B L1: 99.4% 0.6% [libx264 @ 0x7f8ec981d800] kb/s:304.49 Output timelapse4.mp4 (beacause of spam protection I can only post two links with my reputation): http sdm-net.org/data/timelapse4.mp4

  Read the article

• Start a software company offshore

  - by Mascarpone

  Hello Everybody, I own a small, very young, EU based (Italy) company, and among other things, we sell IT solutions. I have a degree in applied mathematics, and I mainly deal with user interfaces, embedded systems, automation and web applications. You can say that I'm an enlightened entrepreneur because I work only with open source software (OS, IDE, I release under BSD , ... everything is free as in freedom), I give high importance to post sales services and customer satisfaction, plus I think I'm the best boss someone could desire (LOL), as I have google in mind when I think about IT workers rights. But the most beautiful thing is that, although everybody advised us not to use open source, is that we are quite profitable!!! (for the sixth trimester in a row). Now I offshore most of the work to an Indian company. I divide the work in modules and I outsource the longer or more trivial ones. I spend a lot of time defining the specifications and I leave the hard work to them. Using productivity bonuses, a lot of prototypes and third-party audits I think that my software has reached a very good quality level. I would like to start my own software development company, in order to improve control over process and cut costs. Obviously I can't afford the cost of labor in the EU, so I thought about opening a company in Asia. What I need Is: 1) Cheap labor - I can afford to give productivity bonuses and higher than average wages and stay profitable just because labor is cheap. 2) Many talents - I need a good level of tertiary education, and a good number of graduates, so I can hire junior developers and train and teach them according to my needs and philosophies (e.g.: open source mind) 3) Good infrastructure - buildings, transport, internet, .... everything that a company might need. I thought about 3 possible candidates: 1) India - I already work with indian people, I know that they are realiable and speak a good english. Big cities are too expensive, but maybe a small city like lucknow http://en.wikipedia.org/wiki/Lucknow could suits my needs. 2) China - They say it's cheaper than India, but I everytime I worked with a chineese company the language was a big barrier. They work hard, are somewhat skilled and cheap but maybe it's a risky path. Plus I feel a little uncofortable with their lack of human rights. 3) Philippines - Same as china: cheaper than india, but maybe less educated. Where do you think it's the best place to start a software company? Any reading or book to advise? thank you very much

  Read the article

• Windows XP - Repairing Corrupt System32\Config\System File

  - by SimonTewsi

  My apologies for this long post. I would like to describe the mess I'm in then ask some questions about how to fix it: Starting up my Windows XP SP1 machine I got the following message: Windows could not start because the following file is missing or corrupt: \WINDOWS\SYSTEM32\CONFIG\SYSTEM Tried restarting several times with same results then Googled the problem. Tried the fix described here: http://icrontic.com/articles/repair%5Fwindows%5Fxp (since my CPU does not have XD buffer overflow protection I did not set /NOEXECUTE=OPTIN as OS Load Option). This did not work. I then found another fix for the problem on hardwareanalysis.com: Basically, boot to dos prompt (or recovery console if available) and make backups of the following files:- c:\windows\system32\config\system (to c:\windows\tmp\system.bak) c:\windows\system32\config\software (to c:\windows\tmp\software.bak) c:\windows\system32\config\sam (to c:\windows\tmp\sam.bak) c:\windows\system32\config\security (to c:\windows\tmp\security.bak) c:\windows\system32\config\default (to c:\windows\tmp\default.bak) then delete the above files (not the backups!) then copy the above files in c:\windows\repair to the c:\windows\system32\config directory restart your computer This did work (and I wish I'd done it first, since it was completely reversible, unlike the first method). However, afterwards I found that all the user accounts on the PC were gone. I resurrected them by copying the backed up security file back into the system32\config folder (I may have copied the SAM file from backup as well, I cannot remember clearly now). Now the PC boots up and I can log in. However things are still not right. I tried to alter one of the user accounts and found I could not access the User Accounts in the Control Panel. Microsoft KB 919292 had a fix for the problem. However, the fix failed with a Windows Installer error: The Windows Installer Service could not be accessed. This can occur if you are running Windows in safe mode, or if Windows Installer is not correctly installed. Contact your support personnel for assistance. Windows Installer 3.1 was already installed. I reinstalled it but continued to get the Windows Installer error whenever I tried to run the fix in KB 919292. I have since noticed another three problems: 1) Several applications on the PC no longer run, eg Microsoft Word. Shortcuts no longer seem to do anything and if I run the executables directly (eg for Word by running C:\Program Files\Microsoft Office\Office10\Winword.exe) I get a message similar to: "Microsoft Word has not been installed for the current user. Please run setup to install the application." even though the executable is clearly visible in Windows Explorer (and even though Word actually opens - the error dialog appears after Word has opened. Clicking OK to the error dialog closes Word). 2) One or the other of the two fixes I tried for the original problem caused new user profiles to be created. eg My old user profile under the Documents and Settings folder was Simon. The old one still exists but there is now a new one called Simon.DBQ2515. Obviously the new one is being used because Opera (my browser that still works) no longer sees the bookmarks file under my old profile. 3) Probably as a result of fooling around with the Security file, when I try to boot off the Windows XP CD and run the Recovery Console I am now asked for the administrator password. The only problem is there is no administrator account on the PC. There is one account, LocalAdmin, that has administrative rights but when I entered the password for that account it did not work. It is so long since I originally set up the PC that I cannot remember if the original administrator account ever had a password and, if so, what it was. So, my question is: How can I fix this mess? In particular: 1) Having tried the two fixes linked to above, have I irrepairably damaged the Windows instance, requiring a clean reinstallation of Windows + all applications, or should it be possible to get the machine working correctly again without such drastic measures? 2) Is there any way to get around the administrator password so I can use the Recovery Console again, given that there is no account called "administrator" and the password for the one account with admin privileges does not work (and that, before I started the second fix, I was not asked for an administrator password)? 3) Is there any easy way to fix the problem with the applications that think they are not installed? 4) Is there any easy way to fix the problem of the Windows Installer that does not work, even if reinstalled? Cheers Simon

  Read the article

• SQL Server database filled the hard drive and freeing up space isn't possible

  - by Jon

  I have a database in SQL Server 2008 on a 1Tb hard drive and it filled the drive, there is only 4Kb free. The MDF file is 323Gb and the LDF is 653Gb. The hard disk this DB is on has no other files on it other than the MDF and LDF so it's impossible to free up any space on the drive. The main hard disk is smaller but there is enough room to transfer the MDF to that drive, in case that helps. This server is overseas at a customer site and it's not possible at the moment to add more disk space to the server. It's also not possible to delete any records because the DB is in a failed mode (due to no disk space) and it doesn't respond to most commands. The Db is currently in full recovery mode which is why the LDF file is so large. This DB really doesn't need to be in full recovery so going forward we plan on switching it to simple mode which will save us a lot of space. I also don't care about losing the LDF file, but I need all of the data. I've spent a lot of time looking for a way out of this problem but everything I've found first involves either freeing up disk space or adding more disk space, neither of which is an option at this time. I'm stuck and any help would be greatly appreciated. I get the following log when trying to switch the DB to online mode. Msg 945, Level 14, State 2, Line 3 Database 'DBNAME' cannot be opened due to inaccessible files or insufficient memory or disk space. See the SQL Server errorlog for details. Msg 5069, Level 16, State 1, Line 3 ALTER DATABASE statement failed. Msg 1101, Level 17, State 12, Line 3 Could not allocate a new page for database 'DBNAME' because of insufficient disk space in filegroup 'DEFAULT'. Create the necessary space by dropping objects in the filegroup, adding additional files to the filegroup, or setting autogrowth on for existing files in the filegroup. I've found the following solutions but none work due to having no disk space on that drive, and since the DB is in a failed state I can't run most commmands. - DBCC SHRINKFILE - can't be run because doing a 'use DBNAME' fails - Detaching the DB and then changing the location of the MDF/LDF files, this fails because the DB is in an offline mode so you can't run detach. I'm at a loss about what else to try. Thanks.

  Read the article

• NIC is receiving, but not transmitting at all?

  - by Shtééf

  I'm trying to fix a very strange problem remotely on a machine at a customer site. The machine is a Dell PowerEdge, I believe a 1950 (haven't verified, but the lspci output matches specs I found.) The machine has two similar NICs, identified as Broadcom Corporation NetXtreme II BCM5708 Gigabit Ethernet (rev 12) by lspci, and using the bnx2 driver. (I suspect these are on-board and on the same controller, which is what I'm accustomed to for this type of machine.) The primary interface eth0 works perfectly, and is in fact how I am ssh'd in. However, the secondary interface eth1 is not transmitting. I can see this in ifconfig output, for example, where the TX field is always 0. However, it is receiving, and tcpdump shows ARP requests coming from the ISP's gateway on the other side. The interface is physically connected to a Siemens BSTU4 modem, configured by the ISP. The link is properly set to 10MBps and full duplex, without negotation, as the ISP requested. A small /30 subnet is configured. For the sake of anonimity, let's say the machine is 3.3.3.2/30, and the ISP's gateway .1. The machine has no firewall settings whatsoever. Even running something like arping -I eth1 3.3.3.1, and running tcpdump alongside, shows no traffic whatsoever being transmitted on the interface. (But the other side keeps steadily sending ARP requests, and that is all that can be seen.) What could be causing this? Here's some output, anonymized, which may hopefully help: $ ethtool eth1 Settings for eth1: Supported ports: [ TP ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Supports auto-negotiation: Yes Advertised link modes: Not reported Advertised auto-negotiation: No Speed: 10Mb/s Duplex: Full Port: Twisted Pair PHYAD: 1 Transceiver: internal Auto-negotiation: off Supports Wake-on: d Wake-on: d Link detected: yes $ ip link show eth1 3: eth1: <BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast qlen 1000 link/ether 00:15:c5:xx:xx:xx brd ff:ff:ff:ff:ff:ff $ ip -4 addr show eth1 3: eth1: <BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast qlen 1000 inet 3.3.3.2/30 brd 3.3.3.3 scope global eth1 $ ip -4 route show match 3.3.3.0/30 3.3.3.0/30 dev eth1 proto kernel scope link src 3.3.3.2 default via 10.0.0.5 dev eth0

  Read the article

• Secure copy uucp style

  - by Alexander Janssen

  I often have the case that I have to make a lot of hops to the remote host, just because there is no direct routing between my client and the remote host. When I need to copy files from a remote host two or more hops away, I always have to: client$ ssh host1 host1$ ssh host2 host2$ scp host3:/myfile . host2$ exit host1$ scp host2:myfile . host1$ exit client$ scp host1:myfile . Back when uucp still was being used this would be as simple as a uucp host1!host2!host3 /myfile . I know that there's uucp over ssh, but unfortunately I don't have the proper privileges on those machines to set it up. Also, I'm not sure if I really want to fiddle around with customer's machines. Does anyone know of a method doing this tasks without the need to setup a lot of tunnels or deploying new software to remote hosts? Maybe some kind of recursive script which clones itself to all the remote hosts, doing the hard work for me? Assume that authentication takes place with public keys and that all hosts do SSH Agent Forwarding. Edit: I'm not looking for a way to automatically forwarding my interactive sesssion to the nexthop host. I want a solution to copy files bangpath-style using scp via multiple hops without the need to install uucp on any of those machines. I don't have the (legal) rights or the privileges to make permanent changes to the ssh-config. Also, I'm sharing this username and hosts with a lot of other people. I'm willing to hack up my own script, but I wanted to know if anyone knows something which already does it. Minimum-invasive changes to hosts on the bangpath, simple invocation from the client. Edit 2: To give you an impression of how it's properly been done in interactive sessions, have a look at the GXPC clustershell. This is basically a Python-script, which spwans itself over to all remote hosts which have connectivity and where your ssh-key is installed. The great thing about it is, that you can tell "I can reach HostC via HostB via HostA." It just works. I want to have this for scp.

  Read the article

• How to open a server port outside of an OpenVPN tunnel with a pf firewall on OSX (BSD)

  - by Timbo

  I have a Mac mini that I use as a media server running XBMC and serves media from my NAS to my stereo and TV (which has been color calibrated with a Spyder3Express, happy). The Mac runs OSX 10.8.2 and the internet connection is tunneled for general privacy over OpenVPN through Tunnelblick. I believe my anonymous VPN provider pushes "redirect_gateway" to OpenVPN/Tunnelblick because when on it effectively tunnels all non-LAN traffic in- and outbound. As an unwanted side effect that also opens the boxes server ports unprotected to the outside world and bypasses my firewall-router (Netgear SRX5308). I have run nmap from outside the LAN on the VPN IP and the server ports on the mini are clearly visible and connectable. The mini has the following ports open: ssh/22, ARD/5900 and 8080+9090 for the XBMC iOS client Constellation. I also have Synology NAS which apart from LAN file serving over AFP and WebDAV only serves up an OpenVPN/1194 and a PPTP/1732 server. When outside of the LAN I connect to this from my laptop over OpenVPN and over PPTP from my iPhone. I only want to connect through AFP/548 from the mini to the NAS. The border firewall (SRX5308) just works excellently, stable and with a very high throughput when streaming from various VOD services. My connection is a 100/10 with a close to theoretical max throughput. The ruleset is as follows Inbound: PPTP/1723 Allow always to 10.0.0.40 (NAS/VPN server) from a restricted IP range >corresponding to possible cell provider range OpenVPN/1194 Allow always to 10.0.0.40 (NAS/VPN server) from any Outbound: Default outbound policy: Allow Always OpenVPN/1194 TCP Allow always from 10.0.0.40 (NAS) to a.b.8.1-a.b.8.254 (VPN provider) OpenVPN/1194 UDP Allow always to 10.0.0.40 (NAS) to a.b.8.1-a.b.8.254 (VPN provider) Block always from NAS to any On the Mini I have disabled the OSX Application Level Firewall because it throws popups which don't remember my choices from one time to another and that's annoying on a media server. Instead I run Little Snitch which controls outgoing connections nicely on an application level. I have configured the excellent OSX builtin firewall pf (from BSD) as follows pf.conf (Apple App firewall tie-ins removed) (# replaced with % to avoid formatting errors) ### macro name for external interface. eth_if = "en0" vpn_if = "tap0" ### wifi_if = "en1" ### %usb_if = "en3" ext_if = $eth_if LAN="{10.0.0.0/24}" ### General housekeeping rules ### ### Drop all blocked packets silently set block-policy drop ### all incoming traffic on external interface is normalized and fragmented ### packets are reassembled. scrub in on $ext_if all fragment reassemble scrub in on $vpn_if all fragment reassemble scrub out all ### exercise antispoofing on the external interface, but add the local ### loopback interface as an exception, to prevent services utilizing the ### local loop from being blocked accidentally. ### set skip on lo0 antispoof for $ext_if inet antispoof for $vpn_if inet ### spoofing protection for all interfaces block in quick from urpf-failed ############################# block all ### Access to the mini server over ssh/22 and remote desktop/5900 from LAN/en0 only pass in on $eth_if proto tcp from $LAN to any port {22, 5900, 8080, 9090} ### Allow all udp and icmp also, necessary for Constellation. Could be tightened. pass on $eth_if proto {udp, icmp} from $LAN to any ### Allow AFP to 10.0.0.40 (NAS) pass out on $eth_if proto tcp from any to 10.0.0.40 port 548 ### Allow OpenVPN tunnel setup over unprotected link (en0) only to VPN provider IPs ### and port ranges pass on $eth_if proto tcp from any to a.b.8.0/24 port 1194:1201 ### OpenVPN Tunnel rules. All traffic allowed out, only in to ports 4100-4110 ### Outgoing pings ok pass in on $vpn_if proto {tcp, udp} from any to any port 4100:4110 pass out on $vpn_if proto {tcp, udp, icmp} from any to any So what are my goals and what does the above setup achieve? (until you tell me otherwise :) 1) Full LAN access to the above ports on the mini/media server (including through my own VPN server) 2) All internet traffic from the mini/media server is anonymized and tunneled over VPN 3) If OpenVPN/Tunnelblick on the mini drops the connection, nothing is leaked both because of pf and the router outgoing ruleset. It can't even do a DNS lookup through the router. So what do I have to hide with all this? Nothing much really, I just got carried away trying to stop port scans through the VPN tunnel :) In any case this setup works perfectly and it is very stable. The Problem at last! I want to run a minecraft server and I installed that on a separate user account on the mini server (user=mc) to keep things partitioned. I don't want this server accessible through the anonymized VPN tunnel because there are lots more port scans and hacking attempts through that than over my regular IP and I don't trust java in general. So I added the following pf rule on the mini: ### Allow Minecraft public through user mc pass in on $eth_if proto {tcp,udp} from any to any port 24983 user mc pass out on $eth_if proto {tcp, udp} from any to any user mc And these additions on the border firewall: Inbound: Allow always TCP/UDP from any to 10.0.0.40 (NAS) Outbound: Allow always TCP port 80 from 10.0.0.40 to any (needed for online account checkups) This works fine but only when the OpenVPN/Tunnelblick tunnel is down. When up no connection is possbile to the minecraft server from outside of LAN. inside LAN is always OK. Everything else functions as intended. I believe the redirect_gateway push is close to the root of the problem, but I want to keep that specific VPN provider because of the fantastic throughput, price and service. The Solution? How can I open up the minecraft server port outside of the tunnel so it's only available over en0 not the VPN tunnel? Should I a static route? But I don't know which IPs will be connecting...stumbles How secure would to estimate this setup to be and do you have other improvements to share? I've searched extensively in the last few days to no avail...If you've read this far I bet you know the answer :)

  Read the article

• Can I use the same machine as a client and server for SSH?

  - by achraf

  For development tests, I need to setup an SFTP server. So I want to know if it's possible to use the same machine as the client and the server. I tried and I keep getting this error: > Permission denied (publickey). > Connection closed and by running ssh -v agharroud@localhost i get : > OpenSSH_3.8.1p1,OpenSSL 0.9.7d 17 Mar > debug1: Reading configuration data /etc/ssh_config > debug1: Connecting to localhost [127.0.0.1] port 22. > debug1: Connection established. > debug1: identity file /home/agharroud/.ssh/identity type -1 > debug1: identity file /home/agharroud/.ssh/id_rsa type 1 > debug1: identity file /home/agharroud/.ssh/id_dsa type -1 > debug1: Remote protocol version 2.0, remote software version OpenSSH_3.8.1p1 > debug1: match: OpenSSH_3.8.1p1 pat OpenSSH* > debug1: Enabling compatibility mode for protocol 2.0 > debug1: Local version string SSH-2.0-OpenSSH_3.8.1p1 > debug1: SSH2_MSG_KEXINIT sent > debug1: SSH2_MSG_KEXINIT received > debug1: kex:server->client aes128-cbc hmac-md5 none > debug1: kex: client->server aes128-cbc hmac-md5 none > debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent > debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP > debug1: SSH2_MSG_KEX_DH_GEX_INIT sent > debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY > debug1: Host 'localhost' is known and matches the RSA host key. > debug1: Found key in /home/agharroud/.ssh/known_hosts:1 > debug1: ssh_rsa_verify: signature correct > debug1: SSH2_MSG_NEWKEYS sent > debug1: expecting SSH2_MSG_NEWKEYS > debug1: SSH2_MSG_NEWKEYS received > debug1: SSH2_MSG_SERVICE_REQUEST sent > debug1: SSH2_MSG_SERVICE_ACCEPT > received > > ****USAGE WARNING**** > > This is a private computer system. This computer system, including all > related equipment, networks, and network devices (specifically > including Internet access) are provided only for authorized use. This > computer system may be monitored for all lawful purposes, including to > ensure that its use is authorized, for management of the system, to > facilitate protection against unauthorized access, and to verify > security procedures, survivability, and operational security. Monitoring > includes active attacks by authorized entities to test or verify the > security of this system. During monitoring, information may be > examined, recorded, copied and used for authorized purposes. All > information, including personal information, placed or sent over this > system may be monitored. > > Use of this computer system, authorized or unauthorized, > constitutes consent to monitoring of this system. Unauthorized use may > subject you to criminal prosecution. Evidence of unauthorized use collected > during monitoring may be used for administrative, criminal, or other > adverse action. Use of this system constitutes consent to monitoring for > these purposes. > > debug1: Authentications that can continue: publickey > debug1: Next authentication method: publickey > debug1: Trying private key:/home/agharroud/.ssh/identity > debug1: Offering public key:/home/agharroud/.ssh/id_rsa > debug1:Authentications that can continue:publickey > debug1: Trying private key:/home/agharroud/.ssh/id_dsa > debug1: No more authentication methods to try. > Permission denied (publickey). Any ideas about the problem ? thanks !

  Read the article

• IE9 Error: There was a pr?blem sending the command to the program

  - by HK1

  I'm working on a new/fresh Windows 7 32bit machine that now has IE9 installed. The user is using the Dell Stardock application as his primary "desktop" (all his links there). When we place an internet link there and click on it we get the following error message: There was a problem sending the command to the program. To me this indicates that IE9 is having trouble going to the website we want to go to, which should get passed as a parameter to the browser when it opens. I don't think this is a StarDock/ObjectDock problem because we also have some other problems with internet links. For example, we cannot move an internet link from the Desktop to the Quick Launch on the task bar. When we do try, it forces us to put the link with the IE icon as part of the IE menu instead of allowing us to have a shortcut there as it's own entry. I should mention however, that links on the desktop and in the taskbar do work as we expect them too (without showing the above error message). It appears that this problem started after installing Windows Updates. Since we installed a whole bunch of updates at once I have no idea which one caused the problem. I did have Google Chrome installed but I uninstalled it since the user wants to use IE. The problem started before I uninstalled Chrome. I also reset the browser settings on IE9. It didn't help. Next I uninstalled IE9 which took me back to IE8. This actually did resolve the problem but the problem came back as soon as I installed IE9 again. We have Verizon Internet Security installed. It's actually a McAfee product rebranded to look like Verizon. I'm not real crazy over this software but the customer has a subscription so we're not planning to change it. I have no reason to believe that this is causing the problem and yet I know that security software is often to blame for strange issues. I've looked at the registry settings for the following keys and everything appears to be ok for every single one of them: HKEY_CLASSES_ROOT\.htm HKEY_CLASSES_ROOT\.html HKEY_CLASSES_ROOT\http\shell\open\command HKEY_CLASSES_ROOT\http\shell\open\ddeexec\Application HKEY_CLASSES_ROOT\https\shell\open\command HKEY_CLASSES_ROOT\https\shell\open\ddeexec\Application HKEY_CLASSES_ROOT\htmlfile\shell\open\command HKEY_CLASSES_ROOT\Microsoft.Website\Shell\Open\Command Edit1: I've found two potential solutions but I won't be able to try them until tomorrow. One is to disable the "Windows Font Cache" service. Another is to clear IE cache and browsing history. I won't be able to try out either solution until tomorrow since this is a remote client's machine. I see there are lots of other suggestions online but if you take the time to read them through you'll see that the other suggestions didn't fix the problem.

  Read the article

• netbook intel GMA 3150 external monitor 1920x1080 flicker problem

  - by seyenne

  Dear all, i recently purchased a acer netbook (apsire one d260). It runs flawlessly. Yesterday I bought a samsung 23" TFT with a native resolution of 1920x1080. According to the information found in the internet and my local computer dealer, the intel chipset can handle the native resolution of the monitor. However, this is only partly the case. I use the VGA cabel to connect, the monitor instantly switches to the native resolution and now the problem: Occasionaly, especially the first 2 hours after booting up, I have a flickering all over the screen, sometimes the entire screen is shaking and spinning around like crazy. I figured out, that lowering the resolution avoids the flicker but this helps only for some time. I can rule out that it's the monitor's problem since I found no issues with another notebook. Right now, I have no problems with the netbook, for about 30 minutes I didn't experience any issues... But I don't know for how long, it occurs without warning :-) I'm worried that if I would bring the netbook back to the dealer and explain my problem, after testing it on an external screen in the local shop, everything works just fine... And I won't get helped with the problem because I can't prove it. (I'm currently in Thailand and over here, customer service is nothing like back home in Germany) What can I do? Is this a driver related issue? (I installed the latest GPU driver) Is it because of the VGA cable? (But why does it work sometimes without any problems and with no issues on the other notebook) I monitored the GPU/CPU temperature, nothing changes really over time..Can it simply be a faulty GPU and is a replacement justifiable? I'm really stressed now because for the time I'm writing, the flickering didn't occur...but for sure, soon or later it will happen again.. I Forgot to mention, the problem also happens if the netbook runs on battery, unplugged. So the only hardware that is plugged is the TFT screen. ...........and here it comes again, flickering has just begun. NEED HELP! Thank you all for reading through this and giving any suggestions if possible. Cheers

  Read the article

• What server setup for a small web development company? [closed]

  - by Giordano

  I co-own a company with a friend of mine and we have decided to buy a new server to support our business (our current server is an Asus EEE Box, working great but too limited :) ). I should mention that we are web developers but occasionally we do small-office sys admin. Thus, 99% of time we work on GNU/Linux (mainly Ubuntu) but from time to time we need to setup a Windows environment to assist some customers (e.g. setup a temporary SQL Server 2008). Our requirements: Low budget: we don't want the cheapest solution out there but we can't afford to spend too much. Budget could be ~1000-1500€ (before VAT) Robustness: we would like to setup a RAID array and maybe have an external disk where we can store backups Virtualization: we need to be able to setup few servers for development. The scenario is something like this (~8 appliances running in parallel): Redmine + GIT server Bacula server FTP server 3-4 virtual appliances that could be set up on demand to test our applications or support a customer. The appliances could be: LAMP, Tomcat+PostgreSQL, SQL Server Support: if something breaks down it shouldn't be too difficult to find a replacement. Now, given the main requirements, there are some doubts we need to clarify: Do you suggest to buy a prepackaged solution (for example a customized Dell PowerEdge T110 or T310) or to assemble the server by ourselves (buy the separate components)? What RAID configuration do you suggest? I was thinking of RAID1 (probably cheaper) or RAID5. should we buy a hardware RAID controller or is it ok to use a software RAID (mdadm)? In case, which controller do you suggest? What processor do you suggest (Intel Xeon, i3, i5, i7, AMD)? How much RAM? (I was thinking at least 8GB, ~1GB per appliance) What virtualization software do you recommend? VMWare seems to be the best choice, but what about XEN or KVM? We don't want to buy licenses at the moment so we would like to consider only free options. What OS do you recommend? We know Ubuntu, Debian, Gentoo very well (we would like to use Ubuntu Server), however it seems a lot of people goes for CentOS. Thanks in advance if you can help us with this! It's our first "serious" server so many doubts popped up :) Please feel free to add further recommendations if you have some to share ;) Have a nice day

  Read the article

• SQL SERVER – Signal Wait Time Introduction with Simple Example – Wait Type – Day 2 of 28

  - by pinaldave

  In this post, let’s delve a bit more in depth regarding wait stats. The very first question: when do the wait stats occur? Here is the simple answer. When SQL Server is executing any task, and if for any reason it has to wait for resources to execute the task, this wait is recorded by SQL Server with the reason for the delay. Later on we can analyze these wait stats to understand the reason the task was delayed and maybe we can eliminate the wait for SQL Server. It is not always possible to remove the wait type 100%, but there are few suggestions that can help. Before we continue learning about wait types and wait stats, we need to understand three important milestones of the query life-cycle. Running - a query which is being executed on a CPU is called a running query. This query is responsible for CPU time. Runnable – a query which is ready to execute and waiting for its turn to run is called a runnable query. This query is responsible for Signal Wait time. (In other words, the query is ready to run but CPU is servicing another query). Suspended – a query which is waiting due to any reason (to know the reason, we are learning wait stats) to be converted to runnable is suspended query. This query is responsible for wait time. (In other words, this is the time we are trying to reduce). In simple words, query execution time is a summation of the query Executing CPU Time (Running) + Query Wait Time (Suspended) + Query Signal Wait Time (Runnable). Again, it may be possible a query goes to all these stats multiple times. Let us try to understand the whole thing with a simple analogy of a taxi and a passenger. Two friends, Tom and Danny, go to the mall together. When they leave the mall, they decide to take a taxi. Tom and Danny both stand in the line waiting for their turn to get into the taxi. This is the Signal Wait Time as they are ready to get into the taxi but the taxis are currently serving other customer and they have to wait for their turn. In other word they are in a runnable state. Now when it is their turn to get into the taxi, the taxi driver informs them he does not take credit cards and only cash is accepted. Neither Tom nor Danny have enough cash, they both cannot get into the vehicle. Tom waits outside in the queue and Danny goes to ATM to fetch the cash. During this time the taxi cannot wait, they have to let other passengers get into the taxi. As Tom and Danny both are outside in the queue, this is the Query Wait Time and they are in the suspended state. They cannot do anything till they get the cash. Once Danny gets the cash, they are both standing in the line again, creating one more Signal Wait Time. This time when their turn comes they can pay the taxi driver in cash and reach their destination. The time taken for the taxi to get from the mall to the destination is running time (CPU time) and the taxi is running. I hope this analogy is bit clear with the wait stats. You can check the Signalwait stats using following query of Glenn Berry. -- Signal Waits for instance SELECT CAST(100.0 * SUM(signal_wait_time_ms) / SUM (wait_time_ms) AS NUMERIC(20,2)) AS [%signal (cpu) waits], CAST(100.0 * SUM(wait_time_ms - signal_wait_time_ms) / SUM (wait_time_ms) AS NUMERIC(20,2)) AS [%resource waits] FROM sys.dm_os_wait_stats OPTION (RECOMPILE); Higher the Signal wait stats are not good for the system. Very high value indicates CPU pressure. In my experience, when systems are running smooth and without any glitch the Signal wait stat is lower than 20%. Again, this number can be debated (and it is from my experience and is not documented anywhere). In other words, lower is better and higher is not good for the system. In future articles we will discuss in detail the various wait types and wait stats and their resolution. Read all the post in the Wait Types and Queue series. Reference: Pinal Dave (http://blog.SQLAuthority.com) Filed under: Pinal Dave, PostADay, SQL, SQL Authority, SQL DMV, SQL Performance, SQL Query, SQL Scripts, SQL Server, SQL Tips and Tricks, SQL Wait Stats, SQL Wait Types, T SQL, Technology

  Read the article

• Ask How-To Geek: Learning the Office Ribbon, Booting to USB with an Old BIOS, and Snapping Windows

  - by Jason Fitzpatrick

  You’ve got questions and we’ve got answers. Today we highlight how to master the new Office interface, USB boot a computer with outdated BIOS, and snap windows to preset locations. Learning the New Office Ribbon Dear How-To Geek, I feel silly asking this (in light of how long the new Office interface has been out) but my company finally got around to upgrading from Windows XP and Office 2000 so the new interface it totally new to me. Can you recommend any resources for quickly learning the Office ribbon and the new changes? I feel completely lost after two decades of the old Office interface. Help! Sincerely, Where the Hell is Everything? Dear Where the Hell, We think most people were with you at some point in the last few years. “Where the hell is…” could possibly be the slogan for the new ribbon interface. You could browse through some of the dry tutorials online or even get a weighty book on the topic but the best way to learn something new is to get hands on. Ribbon Hero turns learning the new Office features and ribbon layout into a game. It’s no vigorous round of Team Fortress mind you, but it’s significantly more fun than reading a training document. Check out how to install and configure Ribbon Hero here. You’ll be teaching your coworkers new tricks in no time. Boot via USB with an Old BIOS Dear How-To Geek, I’m trying to repurpose some old computers by updating them with lightweight Linux distros but the BIOS on most of the machines is ancient and creaky. How ancient? It doesn’t even support booting from a USB device! I have a large flash drive that I’ve turned into a master installation tool for jobs like this but I can’t use it. The computers in question have USB ports; they just aren’t recognized during the boot process. What can I do? USB Bootin’ in Boise Dear USB Bootin’, It’s great you’re working to breathe life into old hardware! You’ve run into one of the limitations of older BIOSes, USB was around but nobody was thinking about booting off of it. Fortunately if you have a computer old enough to have that kind of BIOS it’s likely to also has a floppy drive or a CDROM drive. While you could make a bootable CDROM for your application we understand that you want to keep using the master USB installer you’ve made. In light of that we recommend PLoP Boot Manager. Think of it like a boot manager for your boot manager. Using it you can create a bootable floppy or CDROM that will enable USB booting of your master USB drive. Make a CD and a floppy version and you’ll have everything in your toolkit you need for future computer refurbishing projects. Read up on creating bootable media with PLoP Boot Manager here. Snapping Windows to Preset Coordinates Dear How-To Geek, Once upon a time I had a company laptop that came with a little utility that snapped windows to preset areas of the screen. This was long before the snap-to-side features in Windows 7. You could essentially configure your screen into a grid pattern of your choosing and then windows would neatly snap into those grids. I have no idea what it was called or if was anymore than a gimmick from the computer manufacturer, but I’d really like to have it on my new computer! Bend and Snap in San Francisco, Dear Bend and Snap, If we had to guess, we’d guess your company must have had a set of laptops from Acer as the program you’re describing sounds exactly like Acer GridVista. Fortunately for you the application was extremely popular and Acer released it independently of their hardware. If, by chance, you’ve since upgraded to a multiple monitor setup the app even supports multiple monitors—many of the configurations are handy for arranging IM windows and other auxiliary communication tools. Check out our guide to installing and configuring Acer GridVista here for more information. Have a question you want to put before the How-To Geek staff? Shoot us an email at [email protected] and then keep an eye out for a solution in the Ask How-To Geek column. Latest Features How-To Geek ETC How to Upgrade Windows 7 Easily (And Understand Whether You Should) The How-To Geek Guide to Audio Editing: Basic Noise Removal Install a Wii Game Loader for Easy Backups and Fast Load Times The Best of CES (Consumer Electronics Show) in 2011 The Worst of CES (Consumer Electronics Show) in 2011 HTG Projects: How to Create Your Own Custom Papercraft Toy Download the New Year in Japan Windows 7 Theme from Microsoft Once More Unto the Breach – Facebook Apps Can Now Access Your Address and Phone Number Dial Zero Speeds You Through Annoying Customer Service Menus Complete Dropquest 2011 and Receive Free Dropbox Storage Desktop Computer versus Laptop Wallpaper The Kids Have No Idea What Old Tech Is [Video]

  Read the article

• SQL SERVER – Single Wait Time Introduction with Simple Example – Wait Type – Day 2 of 28

  - by pinaldave

  In this post, let’s delve a bit more in depth regarding wait stats. The very first question: when do the wait stats occur? Here is the simple answer. When SQL Server is executing any task, and if for any reason it has to wait for resources to execute the task, this wait is recorded by SQL Server with the reason for the delay. Later on we can analyze these wait stats to understand the reason the task was delayed and maybe we can eliminate the wait for SQL Server. It is not always possible to remove the wait type 100%, but there are few suggestions that can help. Before we continue learning about wait types and wait stats, we need to understand three important milestones of the query life-cycle. Running - a query which is being executed on a CPU is called a running query. This query is responsible for CPU time. Runnable – a query which is ready to execute and waiting for its turn to run is called a runnable query. This query is responsible for Single Wait time. (In other words, the query is ready to run but CPU is servicing another query). Suspended – a query which is waiting due to any reason (to know the reason, we are learning wait stats) to be converted to runnable is suspended query. This query is responsible for wait time. (In other words, this is the time we are trying to reduce). In simple words, query execution time is a summation of the query Executing CPU Time (Running) + Query Wait Time (Suspended) + Query Single Wait Time (Runnable). Again, it may be possible a query goes to all these stats multiple times. Let us try to understand the whole thing with a simple analogy of a taxi and a passenger. Two friends, Tom and Danny, go to the mall together. When they leave the mall, they decide to take a taxi. Tom and Danny both stand in the line waiting for their turn to get into the taxi. This is the Signal Wait Time as they are ready to get into the taxi but the taxis are currently serving other customer and they have to wait for their turn. In other word they are in a runnable state. Now when it is their turn to get into the taxi, the taxi driver informs them he does not take credit cards and only cash is accepted. Neither Tom nor Danny have enough cash, they both cannot get into the vehicle. Tom waits outside in the queue and Danny goes to ATM to fetch the cash. During this time the taxi cannot wait, they have to let other passengers get into the taxi. As Tom and Danny both are outside in the queue, this is the Query Wait Time and they are in the suspended state. They cannot do anything till they get the cash. Once Danny gets the cash, they are both standing in the line again, creating one more Single Wait Time. This time when their turn comes they can pay the taxi driver in cash and reach their destination. The time taken for the taxi to get from the mall to the destination is running time (CPU time) and the taxi is running. I hope this analogy is bit clear with the wait stats. You can check the single wait stats using following query of Glenn Berry. -- Signal Waits for instance SELECT CAST(100.0 * SUM(signal_wait_time_ms) / SUM (wait_time_ms) AS NUMERIC(20,2)) AS [%signal (cpu) waits], CAST(100.0 * SUM(wait_time_ms - signal_wait_time_ms) / SUM (wait_time_ms) AS NUMERIC(20,2)) AS [%resource waits] FROM sys.dm_os_wait_stats OPTION (RECOMPILE); Higher the single wait stats are not good for the system. Very high value indicates CPU pressure. In my experience, when systems are running smooth and without any glitch the single wait stat is lower than 20%. Again, this number can be debated (and it is from my experience and is not documented anywhere). In other words, lower is better and higher is not good for the system. In future articles we will discuss in detail the various wait types and wait stats and their resolution. Read all the post in the Wait Types and Queue series. Reference: Pinal Dave (http://blog.SQLAuthority.com) Filed under: Pinal Dave, PostADay, SQL, SQL Authority, SQL DMV, SQL Performance, SQL Query, SQL Scripts, SQL Server, SQL Tips and Tricks, SQL Wait Stats, SQL Wait Types, T SQL, Technology

  Read the article

< Previous Page | 234 235 236 237 238 239 240 241 242 243 244 245  | Next Page >