Search Results

Search found 1404 results on 57 pages for 'ati radeon'.

Page 24/57 | < Previous Page | 20 21 22 23 24 25 26 27 28 29 30 31  | Next Page >

• Unable to install ubuntu on a AMD 64 bit system with a AMD Radeon HD 6670 graphics card

  - by Tom Wingrove

  I’ve been running a dual boot system (Ubuntu/Windows7) for two years or so with no problems. I recently built an AMD 64 Bit System, re-installed Windows but when I went to load Ubuntu inside Windows, hit a snag. The screen view during installation became small square blocks of colour, which obviously is a graphics drive problem. I tried various live disks both 32 & 64 bit for, Ubuntu 12.04, 11.10 & 10.10, all but Ubuntu 10.10 had the same problem. Ubuntu 10.10 loaded ok, installed the presented ATI graphics driver as usual but was left with the AMD Unsupported watermark at the bottom right of the screen. The graphics card installed in the computer is an MSI ATI Radeon HD 6670 (in effect an AMD Radeon HD 6670). I am fairly new to linux and while I can install and tweak the OS, I am rather baffled as to what to do. So my question is will an up to date ATI Driver be released in the near future for installation/live disks? Or am I going to have to downgrade my graphics card to use linux? Yours Tom Wingrove

  Read the article

• Ubuntu, No wireless networks found after correctly installed madwifi

  - by Peter

  Hi, I just installed madwifi on my MSI laptop with an Atheros AR5001 wifi card & Lucid. As far as I can see and according to System - Administration - Hardware drivers the install was successful and the card + driver is up and running. However, I don't see any wireless network (my windows PC can see about 5 wireless networks). I tried it with the network manager applet as well as with wicd. If I try to connect to "Hidden Wireless Network" via nm-applet, it will start to connect for a while but is unable too (although I supply it with the correct WEP settings & key) So, I'm unable to use my wireless network. What am i doing wrong? Some information about my system: iwconfig lo no wireless extensions. eth0 no wireless extensions. wifi0 no wireless extensions. ath0 IEEE 802.11g ESSID:"" Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:17 dBm Sensitivity=1/1 Retry:off RTS thr:off Fragment thr:off Power Management:off Link Quality=0/70 Signal level=-96 dBm Noise level=-96 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 pan0 no wireless extensions. ifconfig ath0 Link encap:Ethernet HWaddr 00:15:af:cf:e2:ca inet6 addr: fe80::215:afff:fecf:e2ca/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth0 Link encap:Ethernet HWaddr 00:21:85:4d:82:78 inet addr:192.168.2.101 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::221:85ff:fe4d:8278/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3800 errors:0 dropped:0 overruns:0 frame:0 TX packets:2944 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3940261 (3.9 MB) TX bytes:525218 (525.2 KB) Interrupt:27 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:720 (720.0 B) TX bytes:720 (720.0 B) wifi0 Link encap:UNSPEC HWaddr 00-15-AF-CF-E2-CA-00-00-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3497 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:280 RX bytes:0 (0.0 B) TX bytes:179947 (179.9 KB) Interrupt:16 lshw -C network *-network description: Wireless interface product: AR5001 Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 logical name: wifi0 version: 01 serial: 00:15:af:cf:e2:ca width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix bus_master cap_list logical ethernet physical wireless configuration: broadcast=yes driver=ath_pci latency=0 multicast=yes wireless=IEEE 802.11g resources: irq:16 memory:fd7f0000-fd7fffff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 01 serial: 00:21:85:4d:82:78 size: 100MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.2.101 latency=0 link=yes multicast=yes port=MII speed=100MB/s resources: irq:27 ioport:c800(size=256) memory:fe2ff000-fe2fffff memory:fe2c0000-fe2dffff(prefetchable) lspci 00:00.0 Host bridge: ATI Technologies Inc RS690 Host Bridge 00:01.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (Internal gfx) 00:04.0 PCI bridge: ATI Technologies Inc Device 7914 00:06.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 2) 00:07.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 3) 00:12.0 SATA controller: ATI Technologies Inc SB600 Non-Raid-5 SATA 00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0) 00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1) 00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2) 00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3) 00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4) 00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI) 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 14) 00:14.1 IDE interface: ATI Technologies Inc SB600 IDE 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:05.0 VGA compatible controller: ATI Technologies Inc RS690M [Radeon X1200 Series] 01:05.2 Audio device: ATI Technologies Inc Radeon X1200 Series Audio Controller 02:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01) 05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) 06:04.0 CardBus bridge: O2 Micro, Inc. OZ711MP1/MS1 MemoryCardBus Controller (rev 21) 06:04.2 SD Host controller: O2 Micro, Inc. Integrated MMC/SD Controller (rev 01) 06:04.3 Bridge: O2 Micro, Inc. Integrated MS/xD Controller (rev 01) 06:04.4 FireWire (IEEE 1394): O2 Micro, Inc. Firewire (IEEE 1394) (rev 02) less /proc/modules | grep ath ath_rate_sample 11476 1 - Live 0xf812b000 ath_pci 193197 0 - Live 0xf85c3000 wlan 222892 5 wlan_wep,wlan_scan_sta,ath_rate_sample,ath_pci, Live 0xf8537000 ath_hal 398604 3 ath_rate_sample,ath_pci, Live 0xf8480000 I've been at this for hours now, also tried ndiswrapper and ath5k drivers with no luck, and really could use some help. Cheers.

  Read the article

• Arch linux - strange behaviour after installing fglrx

  - by kosto

  I have a problem with drivers on arch linux. I installed catalyst through unnoficial catalyst repo as wiki says. pacman -S catalyst catalyst-utils aticonfig --initial After this operation i rebooted the system. KDM loaded succesfully, but when i tried to switch to console (ctrl+alt+1/2/3) i saw only some strange dots, like pixels from the text were splitted on the whole screen. I was able to go back to kdm and enter the account details tho. This gave me a hang just before kde loaded. Here's a video where i'm showing above actions. Anybody knows what caused the problem? I can still chroot to fix some issues. Thanks for interest. http://glothriel.org/arch/arch_problem.ogg same thing on gnome / gdm, that's my second try on installing catalyst on arch. Open drivers suck the battery 2x faster. ___________EDIT_____________ Ok, i found a sollution, so i'm posting if someone else shares my problem. Catalyst does not support KMS, so you need to disable it from grub. You must know where are your /etc and /boot paritions mounted. If you have only one partition for / it's even simplier. Mount / on /mnt mount /dev/sdaX /mnt where X is number of the partition where is your / installed arch-chroot /mnt nano /etc/default/grub and add line: GRUB_CMDLINE_LINUX="nomodeset" save and quit then run (this will delete your windows grub configuration) grub-mkconfig -o /boot/grub/grub.cfg exit umount /mnt reboot

  Read the article

• Blue Screen Of Death after Graphics Card Update

  - by John Smith

  I recently installed the game watch dogs After installing it i upgraded the drivers on my graphics card AMD Radion R9 200 series via the catalyst software and since then windows has been crashing on an ad-hoc basis even when sitting idle I have recieved two different sets of errors OXOOOOOOO1 and VIDEO_SCHEDULER_INTERNAL_ERROR I am running windows 8.1 with the driver 14.4 from AMD My PC shouldnt really be having this problem as it is pretty high spec due to my work Any help would be greatly appreciated as it is driving me up the walls a bit [UPDATE 08-06-2014] I have been looking around online and have crashed the PC a few times now trying to recreate the bug I have looked into the event history viewer and gotten the following errors amdacpusrsvc acpusrsvc: IOCTL_ACPKSD_KSD_TO_USR_SVC_SET_FB_APERTURES: FAILED acpusrsvc: GfxMemServiceInitialize: FAILED amdacpusrsvc acpusrsvc: IOCTL_ACPKSD_KSD_TO_USR_SVC_SET_FB_APERTURES: FAILED amdacpusrsvc acpusrsvc: GfxMemServiceInitialize: FAILED I took some advice from the AMD forums to re-install the old drivers to see if they would work. I uninstalled the old ones first and installed directly from the CD I got the warnings below but the driver installed "successfully" The Warnings are amdacpusrsvc acpusrsvc: ConfigureFrameBufferMemory: FAILED. Hopefully this will spark something off for someone Thanks John

  Read the article

• file corruption on read/write 2.6.32-22-server (happens across many kernels)

  - by Jonathan

  Hi Guys, I'm having an issue where after the server has been up for a period of time (~week/few days) the server will start reading corrupt data. For instance when I run a sha1sum of a file after a fresh boot it remains the same. However after a while I will start to get segfaults and from then on whenever I read this file I get a different sha1sum. I've checked S.M.A.R.T with long tests and I've run an extended memtest86+(12 passes) My lspci is as follows: 00:00.0 Host bridge: Advanced Micro Devices [AMD] RS780 Host Bridge 00:01.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (int gfx) 00:06.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 2) 00:07.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 3) 00:11.0 SATA controller: ATI Technologies Inc SB700/SB800 SATA Controller [AHCI mode] 00:12.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller 00:12.1 USB Controller: ATI Technologies Inc SB700 USB OHCI1 Controller 00:12.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller 00:13.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller 00:13.1 USB Controller: ATI Technologies Inc SB700 USB OHCI1 Controller 00:13.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 3c) 00:14.1 IDE interface: ATI Technologies Inc SB700/SB800 IDE Controller 00:14.3 ISA bridge: ATI Technologies Inc SB700/SB800 LPC host controller 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 00:14.5 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI2 Controller 00:18.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control 00:18.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control 01:05.0 VGA compatible controller: ATI Technologies Inc Radeon HD 3300 Graphics 01:05.1 Audio device: ATI Technologies Inc RS780 Azalia controller 02:00.0 Ethernet controller: Atheros Communications Atheros AR8121/AR8113/AR8114 PCI-E Ethernet Controller (rev b0) 03:00.0 FireWire (IEEE 1394): VIA Technologies, Inc. Device 3403 I could really use some help on this, do you have any idea what could cause this? It's really frustrating me as it seems to trigger entirely randomly and will not go away until I reboot. I'm also use KVM for virtualization as well as MD for software RAID on this server and the processor is a Phenom II X4 965. I don't believe it's the software raid however as this affects files also hosted on non-raid partitions so I don't know.

  Read the article

• HD 6970 Corrupted Video

  - by FailedDev

  considering this rig : i7 2600K 8GB RAM Corsair Vengeance kit 10-9-10-27 @1866 HD 4870 PSU Corsair AX 1200 I recently upgraded to a HD 6970 and I am getting the following - not so nice screens : http://imageshack.us/g/213/1000142z.jpg/ Had anyone any similar trouble at all? I am thinking that the card is DOA but could it also be the Mobo? Since I am in the BIOS I can't think how the mobo could be the problem. HD 4870 works perfect btw regardless of what I throw at it. Any way to prove that the card is OK? Thanks

  Read the article

• Catalyst Control Center removal

  - by Allan

  I've recently tested a graphics card on a machine that required different drivers than my onboard integrated graphics, so I had catalyst control center installed. After I pulled out the graphics card and went back to using the onboard graphics, I deleted the catalyst center through control panel - programs.. which was fine. But apparently it didn't really remove it. it doesn't show up under programs anymore but when I reboot windows I get an error saying "The catalyst Control Center is not supported by the driver version of your enabled graphics adapter" and its still in the process bar... how do I permanently remove it?

  Read the article

• Toshiba Satellite A305-S6861 Display Problems

  - by brock029

  Well this is the first Laptop I have ever worked on with a dedicated video card. So, there is no video going to the laptops monitor or to an external. Ripped it apart found the gpu and now am stuck. I cant decide if its the gpu that has gone out or the motherboard. Any one have any suggestions? If it were a desktop I would throw in one of my spare video cards. Mainly I don't want to order the video card and eat the $50 if its the motherboard.

  Read the article

• Program for managing multiple monitors to keep from rearranging Windows

  - by Rumel

  I have a setup in use where I use up to four monitors. The problem is I generally switch around what I'm using and that messes up where all of my windows are. I'm on Windows 8 and have two graphics cards. My setup is as follows: Monitor 1: Card 1 Monitor 2: Card 1 Monitor 3: Card 2 TV 1: Card 2 I almost always have all the monitors turned on and in use. When I turn on the TV though, all of my windows get reconfigured and moved to different monitors. I don't know how to stop this. Another configuration I use is where I have Monitors 1 and 2 plus TV in use, and I have my Xbox in use on Monitor 3. When I get done with the Xbox and switch Monitor 3 over to the PC, everything is reconfigured. So is there a program out there that can help with this? I have the free version of Display Fusion in use but haven't seen settings to save monitor configurations.

  Read the article

• Ubuntu 12.10 Trackpoint not detected Thinkpad X130e

  - by killerknives

  I just did a fresh install of 12.10 and now only my touchpad works. The trackpoint and Left/Right buttons below the trackpoint do not work. The trackpoint worked fine as of 12.04. I've searched online and there was a hack that said that disabling the touchpad would enable the trackpoint. WRONG! You'll end up having to use the keyboard =/. I don't know what is needed so I'll just dump some stuff. lspci: 00:00.0 Host bridge: Advanced Micro Devices [AMD] Family 14h Processor Root Complex 00:01.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI Wrestler [Radeon HD 6310] 00:01.1 Audio device: Advanced Micro Devices [AMD] nee ATI Wrestler HDMI Audio [Radeon HD 6250/6310] 00:05.0 PCI bridge: Advanced Micro Devices [AMD] Family 14h Processor Root Port 00:06.0 PCI bridge: Advanced Micro Devices [AMD] Family 14h Processor Root Port 00:07.0 PCI bridge: Advanced Micro Devices [AMD] Family 14h Processor Root Port 00:11.0 SATA controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode] 00:12.0 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:12.2 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:13.0 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:13.2 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:14.0 SMBus: Advanced Micro Devices [AMD] nee ATI SBx00 SMBus Controller (rev 42) 00:14.2 Audio device: Advanced Micro Devices [AMD] nee ATI SBx00 Azalia (Intel HDA) (rev 40) 00:14.3 ISA bridge: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 LPC host controller (rev 40) 00:14.4 PCI bridge: Advanced Micro Devices [AMD] nee ATI SBx00 PCI to PCI Bridge (rev 40) 00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 0 (rev 43) 00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 1 00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 2 00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 3 00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 4 00:18.5 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 6 00:18.6 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 5 00:18.7 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 7 01:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter (rev 01) 02:00.0 Ethernet controller: Atheros Communications Inc. AR8151 v2.0 Gigabit Ethernet (rev c0) I've installged gpointing-device-setting and it only lists the touchpad. No trackpoint. What should I do? What data do you need?

  Read the article

• Radeon HD4850 card, ubuntu 12.04.1 LTS Installed FGLRX drivers, but still running vesa, how to solve it?

  - by user113416

  I have ati HD4850 card, ubuntu 12.04.1LTS. To begin with, after fresh instll, i installed fglrx drvers from system -- additional drivers, according to fglrxifo everything was alright, but the system was running on vesa:sem. After that, i have reinstalled and installed drivers according to many tutorials, but stille got that problem. one of the tutorial was here: What is the correct way to install ATI Catalyst Video Drivers (fglrx)? of course, i attempted to install 12.6 driver Now i have a fresh install of ubuntu and don't want to touch anything without anyone's support, because my 3 days nightmare didn't give results. what must i do to have an adequate performance of video card? Thanks in advace.

  Read the article

• Ubuntu Eye-Infinity across 3 displays

  - by Peter G Mac.

  So I purchased a computer recently and have been trying to customise the display. Radeon 6800 series Ubuntu 10.10 I have three 22inch 1080P lcd monitors that are mounted together. Everything is working smooth. How do I get the 'big-desktop' display where I have one enormous display across all monitors? Linux - ATI Catalyst Control Center 11.2 does not give me an option to 'group' my profiles like the pictures on their site show with Windows. I have been searching all over for help. Much Obliged, -Peter

  Read the article

• I have a problem with a AE1200 Cisco/Linksys Wireless-N USB adapter having stopped working after I ran the update manager in Ubuntu 12.04

  - by user69670

  Here is the problem, I use a Cisco/Linksys AE1200 wireless network adapter to connect my desktop to a public wifi internet connection. I use ndiswrapper to use the windows driver and it had been working fine for me untill I ran the update manager overnight a few days ago. When I woke up it was asking for the normal computer restart to implement the changes but after rebooting the computer, the wireless adapter did not work, the status light on the adapter did not light up even though ubuntu recognizes it is there and according to ndiswrapper the drivers are loaded and the hardware is present. the grep command is being a bitch for some unknown reason today so this will be long sorry Output from "lspci": 00:00.0 Host bridge: Advanced Micro Devices [AMD] nee ATI Radeon Xpress 200 Host Bridge (rev 01) 00:01.0 PCI bridge: Advanced Micro Devices [AMD] nee ATI RS480 PCI Bridge 00:12.0 SATA controller: Advanced Micro Devices [AMD] nee ATI SB600 Non-Raid-5 SATA 00:13.0 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI0) 00:13.1 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI1) 00:13.2 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI2) 00:13.3 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI3) 00:13.4 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI4) 00:13.5 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB Controller (EHCI) 00:14.0 SMBus: Advanced Micro Devices [AMD] nee ATI SBx00 SMBus Controller (rev 13) 00:14.1 IDE interface: Advanced Micro Devices [AMD] nee ATI SB600 IDE 00:14.3 ISA bridge: Advanced Micro Devices [AMD] nee ATI SB600 PCI to LPC Bridge 00:14.4 PCI bridge: Advanced Micro Devices [AMD] nee ATI SBx00 PCI to PCI Bridge 01:05.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI RC410 [Radeon Xpress 200] 02:02.0 Communication controller: Conexant Systems, Inc. HSF 56k Data/Fax Modem 02:03.0 Multimedia audio controller: Creative Labs CA0106 Soundblaster 02:05.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Output from "lsusb": Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 009: ID 13b1:0039 Linksys AE1200 802.11bgn Wireless Adapter [Broadcom BCM43235] Bus 003 Device 002: ID 045e:0053 Microsoft Corp. Optical Mouse Bus 004 Device 002: ID 1043:8006 iCreate Technologies Corp. Flash Disk 32-256 MB Output from "ifconfig": eth0 Link encap:Ethernet HWaddr 00:19:21:b6:af:7c UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:20 Base address:0xb400 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:13232 errors:0 dropped:0 overruns:0 frame:0 TX packets:13232 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1084624 (1.0 MB) TX bytes:1084624 (1.0 MB) Output from "iwconfig": lo no wireless extensions. eth0 no wireless extensions. Output from "lsmod": Module Size Used by nls_iso8859_1 12617 1 nls_cp437 12751 1 vfat 17308 1 fat 55605 1 vfat uas 17828 0 usb_storage 39646 1 nls_utf8 12493 1 udf 84366 1 crc_itu_t 12627 1 udf snd_ca0106 39279 2 snd_ac97_codec 106082 1 snd_ca0106 ac97_bus 12642 1 snd_ac97_codec snd_pcm 80845 2 snd_ca0106,snd_ac97_codec rfcomm 38139 0 snd_seq_midi 13132 0 snd_rawmidi 25424 2 snd_ca0106,snd_seq_midi bnep 17830 2 parport_pc 32114 0 bluetooth 158438 10 rfcomm,bnep ppdev 12849 0 snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51567 2 snd_seq_midi,snd_seq_midi_event snd_timer 28931 2 snd_pcm,snd_seq snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq snd 62064 11 snd_ca0106, snd_ac97_codec,snd_pcm,snd_rawj9fe snd_ca0106,snd_ac97_codec,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device soundcore 14635 1 snd snd_page_alloc 14108 2 snd_ca0106,snd_pcm sp5100_tco 13495 0 i2c_piix4 13093 0 radeon 733693 3 ttm 65344 1 radeon drm_kms_helper 45466 1 radeon drm 197692 5 radeon,ttm,drm_kms_helper i2c_algo_bit 13199 1 radeon mac_hid 13077 0 shpchp 32325 0 ati_agp 13242 0 lp 17455 0 parport 40930 3 parport_pc,ppdev,lp usbhid 41906 0 hid 77367 1 usbhid 8139too 23283 0 8139cp 26759 0 pata_atiixp 12999 1 Output from "sudo lshw -C network": *-network description: Ethernet interface product: RTL-8139/8139C/8139C+ vendor: Realtek Semiconductor Co., Ltd. physical id: 5 bus info: pci@0000:02:05.0 logical name: eth0 version: 10 serial: 00:19:21:b6:af:7c size: 10Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 10 0bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=8139too driverversion=0.9.28 duplex=half latency=64 link=no maxlatency=64 mingnt=32 multicast=yes port=MII speed=10Mbit/s resources: irq:20 ioport:b400(size=256) memory:ff5fdc00-ff5fdcff Output from "iwlist scan": lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. Output from "lsb_release -d": Ubuntu 12.04 LTS Output from "uname -mr": 3.2.0-24-generic-pae i686 Output from "sudo /etc/init.d/networking restart": * Running /etc/init.d/networking restart is deprecated because it may not enable again some interfaces * Reconfiguring network interfaces... [ OK ]

  Read the article

• HP Pavilion tx2000 - Wifi adapter no longer works after moving from 12.04 to a 12.10 clean install

  - by Marek L.

  I have a HP Pavilion tx2000 that I have been running Ubuntu 12.04 on for a couple of months without any problems (wifi worked great) until yesterday when my hard drive failed. I replaced the hard drive and decided to install Ubuntu 12.10. Unlike 12.04, the wifi did not work after the installation finished and all the updates where installed (over Ethernet). The network drop down in the top right didn't even show a wireless option. I Googled about for a bit and found some solutions that seemed like they might work. Unfortunately they did not. Here is what I tried: sudo apt-get remove bcmwl-kernel-source sudo apt-get install b43-fwcutter sudo apt-get install firmware-b43-lpphy-installer Restart the computer. And the wifi still didn't work. At which point I panicked a bit and tried to undo the previous commands by running: sudo apt-get remove b43-fwcutter firmware-b43-lpphy-installer sudo apt-get install bcmwl-kernel-source Restart the computer. The wifi still doesn't work. This is where I stopped because I have no idea what I am doing and don't want to mess something up. The network drop down still doesn't show a wireless option and the hardware wifi switch on the laptop is amber (it turns blue when the wifi is on). Using the hardware switch does not change the color. Output from: sudo lspci ... 08:00.0 Network controller: Broadcom Corporation BCM4322 802.11a/b/g/n Wireless LAN Controller (rev 01) ... Output from: sudo lshw -class network *-network UNCLAIMED description: Network controller product: BCM4322 802.11a/b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:08:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:d1100000-d1103fff ... Output from: sudo rfkill list all 0: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: yes UPDATE: After writing up this question tried the following command: sudo rfkill unblock all At first it didn't do anything but after running it about four times, sudo rfkill list all now returns: 0: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no But the network menu still does not have a wireless option and the hardware switch still glows amber. Pushing the hardware switch turns the hard block back on and I have to run sudo rfkill unblock all multiple times again to turn it off. Any help is appreciated! Update 2: Full output from sudo lspci -nn: 00:00.0 Host bridge [0600]: Advanced Micro Devices [AMD] RS780 Host Bridge [1022:9600] 00:01.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780/RS880 PCI to PCI bridge (int gfx) [1022:9602] 00:04.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780/RS880 PCI to PCI bridge (PCIE port 0) [1022:9604] 00:05.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780/RS880 PCI to PCI bridge (PCIE port 1) [1022:9605] 00:06.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 2) [1022:9606] 00:11.0 SATA controller [0106]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode] [1002:4391] 00:12.0 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI0 Controller [1002:4397] 00:12.1 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0 USB OHCI1 Controller [1002:4398] 00:12.2 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB EHCI Controller [1002:4396] 00:13.0 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI0 Controller [1002:4397] 00:13.1 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0 USB OHCI1 Controller [1002:4398] 00:13.2 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB EHCI Controller [1002:4396] 00:14.0 SMBus [0c05]: Advanced Micro Devices [AMD] nee ATI SBx00 SMBus Controller [1002:4385] (rev 3a) 00:14.1 IDE interface [0101]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 IDE Controller [1002:439c] 00:14.2 Audio device [0403]: Advanced Micro Devices [AMD] nee ATI SBx00 Azalia (Intel HDA) [1002:4383] 00:14.3 ISA bridge [0601]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 LPC host controller [1002:439d] 00:14.4 PCI bridge [0604]: Advanced Micro Devices [AMD] nee ATI SBx00 PCI to PCI Bridge [1002:4384] 00:14.5 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI2 Controller [1002:4399] 00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] Family 11h Processor HyperTransport Configuration [1022:1300] (rev 40) 00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] Family 11h Processor Address Map [1022:1301] 00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] Family 11h Processor DRAM Controller [1022:1302] 00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] Family 11h Processor Miscellaneous Control [1022:1303] 00:18.4 Host bridge [0600]: Advanced Micro Devices [AMD] Family 11h Processor Link Control [1022:1304] 01:05.0 VGA compatible controller [0300]: Advanced Micro Devices [AMD] nee ATI RS780M/RS780MN [Mobility Radeon HD 3200 Graphics] [1002:9612] 08:00.0 Network controller [0280]: Broadcom Corporation BCM4322 802.11a/b/g/n Wireless LAN Controller [14e4:432b] (rev 01) 09:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 02)

  Read the article

• Problem with UBUNTU 10.4 and ATI

  - by Maximilinao

  hola, ando teniendo un problema al instalar los drivers de la placa de video. Apenas termino de instalar los driver, reinicio mi sistema operativo, y al iniciar mi monitor queda apagado en modo ahorro de energia y UBUNTU no inicia. ¿Que puedo hacer?. Perdon por mi ingles. he usado el traductor de google

  Read the article

• LINQ TO SQL error: An attempt has been made to Attach or Add an entity that is not new...

  - by Collin Estes

  "An attempt has been made to Attach or Add an entity that is not new, perhaps having been loaded from another DataContext. This is not supported." I have scene a lot of solutions dealing with the Attach() method but I'm just trying to add in a new record. Not sure what is going on. Here is my code, It is failing on the star'd line.: try { LINQDataContext datacontext = new LINQDataContext(); TrackableItem ti = datacontext.TrackableItems.FirstOrDefault(_t => _t.pkId == obj.fkTrackableItemId); arcTrackableItem ati = new arcTrackableItem(); ati.barcode = ti.barcode; ati.dashNumber = ti.dashNumber; ati.dateDown = ti.dateDown; ati.dateUp = ti.dateUp; ati.fkItemStatusId = ti.fkItemStatusId; ati.fkItemTypeId = ti.fkItemTypeId; ati.partNumber = ti.partNumber; ati.serialNumber = ti.serialNumber; ati.archiveDate = DateTime.Now; datacontext.arcTrackableItems.InsertOnSubmit(ati); datacontext.SubmitChanges(); arcPWR aItem = new arcPWR(); aItem.comments = obj.comments; aItem.fkTrackableItemId = ati.pkId; aItem.fkPWRStatusId = obj.fkPWRStatusId; aItem.PwrStatus = obj.PwrStatus; **datacontext.arcPWRs.InsertOnSubmit(aItem);** datacontext.SubmitChanges();

  Read the article

• Intel Atom: NVIDIA ION vs. Radeon HD 4330 Graphics

  <b>Phoronix:</b> "Before devoting this hardware to the farm, we ran a few benchmarks comparing the performance of NVIDIA's ION GeForce 9400M graphics processor to the ATI Radeon HD 4330 graphics processor found on the MSI 6667BB-004US and several other Atom-powered devices."

  Read the article

• Radeon all in Wonder 8500 Series, Why is it Called so?

  Possess a radeon all in wonder 8500 series and a 128-bit DDR memory and you can push your personal computer to its extreme with an astounding 3-D performance with additional TV, DVD and video editing... [Author: Sunny Makkar - Computers and Internet - March 20, 2010]

  Read the article

• Wondering How Good The Radeon 9700 Pro Drivers Are? Then Just Read Along

  The Radeon 9700 pro drivers is a high-quality card that is at the zenith of the charts based on 3D ground and is a strong competitor to the NVIDIA card. This is the epitome of all the gaming cards an... [Author: Sunny Makkar - Computers and Internet - March 20, 2010]

  Read the article

• If You Truly Want To Make the Best of Your Radeon 9800 Pro Driver Then You Should Get Focus on The F

  The Radeon 9800 pro driver needs connection to the inner power supply of your desktop system for it to operate. If your system does not have the necessary power source, a number of internal devices c... [Author: Sunny Makkar - Computers and Internet - March 20, 2010]

  Read the article

• ATI Problems? An Easy Method to See if the x600 Radeon Drivers are Working

  Many things can cause the x600 radeon driver to stop working, as they should when installed correctly. But when the video card shows trouble signs, you are never sure what the problem is and you need... [Author: Sunny Makkar - Computers and Internet - March 20, 2010]

  Read the article

• Graphics card ATI Asus 9250 128 MB AGP problem.Monitor switching off.

  - by Dominick1978

  I have an old system with these specs: Motherboard: Via P4x266a (with AGP 4x) CPU: P4 1,7 Ghz Memory: 1152 MB DDR SDRAM Graphics card: Voodoo 3 2000 16 MB PSU: 300 Watt It also has 1 dvd-rom, 1 dvd-rw, 2 hard drives (all 4 connected via molex) , 1 sounblaster sound card and 1 ethernet card (both connected via pci). OS: XP Pro Recently I bought Asus 9250 128 MB AGP to replace voodoo.Wnen I switch on the pc the initial screens (until after the xp logo) sometimes are distorted with blurred colours.When XP are loaded there is some flickering but the rest are ok.XP can't recognize the card seeing it as just a VGA adapter.I have downloaded the latest xp drivers from ATI website and installed them.Then after the restart everything is ok (no distorted image or blurring) until after the xp logo.After this the monitor turns off while the pc is still running.I have tried many drivers but the problem persists (of course I removed the voodoo drivers before from the display adapter properties).Only once I have managed to enter XP (after changing BIOS features for graphics card from 256 MB to 128 MB) but the drivers on the control panel had an exclamation mark (ati 9250!) and below them ati 9250 secondary without ! under the display adapter tab and the ATI catalyst program said that it couldn;t find the card.That was the opnly time I went beyond the xp logo.Now the monitor auto switcheS off. So, what do you think? 1)Is this a broken card? 2)Is it the drivers of the card? 3)Is it PSU fault? 4)Anything else? Thanks for your help and excuse my english!

  Read the article

• Why does Ubuntu Freezes on ASUS K42DY laptop with RADEON HD6470M Graphics Card?

  - by ix3

  Hi,I have an ASUS K42DY laptop with AMD Phenom II x2, 8 GB Ram , 500 GB Hard Drive and has a didicated ATI RADEON HD 6470M Graphics Card and I'm running Ubuntu 12.04 LTS 64bit on it. I have installed GNOME 3 and also followed this Make Ubuntu look like Mac OS X. I have also installed apps from the software center, getdeb & playdeb all of which worked fine. However, I noticed that Ubuntu freezes after inactivity let's say 1-3hrs. I have already set power setting to never standby or hibernate. This is completely annoying because all I can do is log-out via ctrl+alt+del or manually shut down and reboot my laptop. What should I do? By the way, this happens on all shells Unity, Gnome (even with the basic) and Cairo Dock.I set Swap Space at 8GB during installation. Any help will be appreciated. Thanks!

  Read the article

• Upgraded Ubuntu from 12.04 to 12.10 Ati radeon HD 3450 Catastrophe!

  - by minime

  When I had upgraded everything was ready on the screen om my computer and with my 12.04 ubuntu. When I restarted my system, the graphics card was not detected. I was forced to start the computer in low graphics mode, and eventually I had a pink deskop with only my maps, and no other programs at all. What do I do now? I need to recover the pictures on my system so that I can upload them online. I'd done a graphics card test on the terminal initially, and it showed that the card was compatible with unity 3D. I have an ATI radeon HD 3450 and I was running a 32 bit build of Ubuntu 12.04 initially Right now I have a broken install of Linux, with no working graphics card or desktop to start from, so I'm unsure of how to fix this.

  Read the article

• help with xorg.conf: xrandr on one of two widescreen monitors; rhel5, kde, ATI Radeon X1300

  - by user35997

  Can anyone help with me configure my dual-screen monitors for rotation? I have xrandr 1.1. Have tried various approaches, nothing takes. I can't even get the xrandr options to show up in KDE's Display control panel. Thanks1 My lspci output: 03:00.0 VGA compatible controller: ATI Technologies Inc RV516 [Radeon X1300/X1550 Series] My current xorg.conf (works, minus screen rotation): # Xorg configuration created by system-config-display Section "ServerLayout" Identifier "Multihead layout" Screen 0 "aticonfig-Screen[0]" 0 0 InputDevice "Keyboard0" "CoreKeyboard" Option "Xinerama" "off" Option "Clone" "on" EndSection Section "Files" EndSection Section "Module" EndSection Section "InputDevice" Identifier "Keyboard0" Driver "kbd" Option "XkbModel" "pc105" Option "XkbLayout" "us" EndSection Section "Monitor" ### Comment all HorizSync and VertSync values to use DDC: Identifier "Monitor1" VendorName "Monitor Vendor" ModelName "Dell 2407WFP (Digital)" HorizSync 30.0 - 83.0 VertRefresh 56.0 - 76.0 Option "dpms" EndSection Section "Monitor" Identifier "aticonfig-Monitor[0]" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" EndSection Section "Device" Identifier "Videocard0" Driver "vesa" EndSection Section "Device" Identifier "Videocard1" Driver "vesa" VendorName "Videocard Vendor" BoardName "ATI Technologies Inc RV516 [Radeon X1300/X1550 Series]" BusID "PCI:3:0:0" EndSection Section "Device" Identifier "aticonfig-Device[0]" Driver "fglrx" Option "DesktopSetup" "horizontal" EndSection Section "Screen" Identifier "Screen0" Device "Videocard0" DefaultDepth 16 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection SubSection "Display" Viewport 0 0 Depth 16 EndSubSection EndSection Section "Screen" Identifier "Screen1" Device "Videocard1" Monitor "Monitor1" DefaultDepth 16 SubSection "Display" Viewport 0 0 Depth 16 Modes "1920x1200" "1280x1024" "800x600" EndSubSection EndSection Section "Screen" Identifier "aticonfig-Screen[0]" Device "aticonfig-Device[0]" Monitor "aticonfig-Monitor[0]" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 Modes "1920x1200" "1280x1024" "800x600" EndSubSection EndSection

  Read the article

< Previous Page | 20 21 22 23 24 25 26 27 28 29 30 31  | Next Page >