Search Results

Search found 1404 results on 57 pages for 'ati radeon'.

Page 29/57 | < Previous Page | 25 26 27 28 29 30 31 32 33 34 35 36  | Next Page >

  • What DX level does my graphics card support? Does it go to 11?

    - by Daniel Moth
    Recently I run into a situation that I have run into quite a few times. Someone encounters a machine and the question arises: "Is there a DirectX 11 card in this machine?". Typically the reason you are interested in that is because cards with DirectX 11 drivers fully support DirectCompute (and by extension C++ AMP) for GPGPU programming. The driver specifically is WDDM (1.1 on Windows 7 and Windows 8 introduces WDDM 1.2 with cool new capabilities). There are many ways for figuring out if you have a DirectX11 card, so here are the approaches that you can use, with a bonus right at the end of the post. Run DxDiag WindowsKey + R, type DxDiag and hit Enter. That is the DirectX diagnostic tool, which unfortunately, only tells you on the "System" tab what is the highest version of DirectX installed on your machine. So if it reports DirectX 11, that doesn't mean you have a DX11 driver! The "Display" tab has a promising "DDI version" label, but unfortunately that doesn't seem to be accurate on the machines I've tested it with (or I may be misinterpreting its use). Either way, this tool is not the one you want for this purpose, although it is good for telling you the WDDM version among other things. Use the Microsoft hardware page There is a Microsoft Windows 7 compatibility center, that lists all hardware (tip: use the advanced search) and you could try and locate your device there… good luck. Use Wikipedia or the hardware vendor's website Use the Wikipedia page for the vendor cards, for both nvidia and amd. Often this information will also be in the specifications for the cards on the IHV site, but is is nice that wikipedia has a single page per vendor that you can search etc. There is a column in the tables for API support where you can see the DirectX version. Check if it is one of these recommended DX11 cards You may not have a DirectX 11 card and are interested in purchasing one. While I am in no position to make recommendations, I will list here some cards from two big IHVs that we know are DirectX 11 capable. Some AMD (aka ATI) cards Low end, inexpensive DX11 hardware: Radeon 5450, 5550, 6450, 6570 Mid range (decent perf, single precision): Radeon 5750, 5770, 6770, 6790 High end (capable of double precision): Radeon 5850, 5870, 6950, 6970 Single precision APUs: AMD E-Series APUs AMD A-Series APUs Some NVIDIA cards Low end, inexpensive DX11 hardware: GeForce GT430, GT 440, GT520, GTS 450 Quadro 400, 600 Mid-range (decent perf, single precision): GeForce GTX 460, GTX 550 Ti, GTX 560, GTX 560 Ti Quadro 2000 High end (capable of double precision): GeForce GTX 480, GTX 570, GTX 580, GTX 590, GTX 595 Quadro 4000, 5000, 6000 Tesla C2050, C2070, C2075 Get the DirectX SDK and run DirectX Caps Viewer Download and install the June 2010 DirectX SDK. As part of that you now have the DirectX Capabilities Viewer utility (find it in your start menu by searching for "DirectX Caps Viewer", the filename is DXCapsViewer.exe). It will list all your devices (emulated, and real hardware ones) under the first node. Expand the hardware entries and then expand again the Direct3D 11 folder. If you see D3D_FEATURE_LEVEL_11_ under that, then your card supports feature level 11 which means it supports DirectCompute and C++ AMP. In the following screenshot of one of my old laptops, the card only goes to feature level 10. Run a utility from the web that just tells you! Of course, writing some C++ AMP code that enumerates accelerators and lists the ones that are capable is trivial. However that requires that you have redistributed the runtime, so a more broadly applicable approach is to use the DX APIs directly to enumerate the DX11 capable cards. That is exactly what the development lead for C++ AMP has done and he describes and shares that utility at this post. Comments about this post by Daniel Moth welcome at the original blog.

    Read the article

  • What DX level does my graphics card support? Does it go to 11?

    - by Daniel Moth
    Recently I run into a situation that I have run into quite a few times. Someone encounters a machine and the question arises: "Is there a DirectX 11 card in this machine?". Typically the reason you are interested in that is because cards with DirectX 11 drivers fully support DirectCompute (and by extension C++ AMP) for GPGPU programming. The driver specifically is WDDM (1.1 on Windows 7 and Windows 8 introduces WDDM 1.2 with cool new capabilities). There are many ways for figuring out if you have a DirectX11 card, so here are the approaches that you can use, with a bonus right at the end of the post. Run DxDiag WindowsKey + R, type DxDiag and hit Enter. That is the DirectX diagnostic tool, which unfortunately, only tells you on the "System" tab what is the highest version of DirectX installed on your machine. So if it reports DirectX 11, that doesn't mean you have a DX11 driver! The "Display" tab has a promising "DDI version" label, but unfortunately that doesn't seem to be accurate on the machines I've tested it with (or I may be misinterpreting its use). Either way, this tool is not the one you want for this purpose, although it is good for telling you the WDDM version among other things. Use the Microsoft hardware page There is a Microsoft Windows 7 compatibility center, that lists all hardware (tip: use the advanced search) and you could try and locate your device there… good luck. Use Wikipedia or the hardware vendor's website Use the Wikipedia page for the vendor cards, for both nvidia and amd. Often this information will also be in the specifications for the cards on the IHV site, but is is nice that wikipedia has a single page per vendor that you can search etc. There is a column in the tables for API support where you can see the DirectX version. Check if it is one of these recommended DX11 cards You may not have a DirectX 11 card and are interested in purchasing one. While I am in no position to make recommendations, I will list here some cards from two big IHVs that we know are DirectX 11 capable. Some AMD (aka ATI) cards Low end, inexpensive DX11 hardware: Radeon 5450, 5550, 6450, 6570 Mid range (decent perf, single precision): Radeon 5750, 5770, 6770, 6790 High end (capable of double precision): Radeon 5850, 5870, 6950, 6970 Single precision APUs: AMD E-Series APUs AMD A-Series APUs Some NVIDIA cards Low end, inexpensive DX11 hardware: GeForce GT430, GT 440, GT520, GTS 450 Quadro 400, 600 Mid-range (decent perf, single precision): GeForce GTX 460, GTX 550 Ti, GTX 560, GTX 560 Ti Quadro 2000 High end (capable of double precision): GeForce GTX 480, GTX 570, GTX 580, GTX 590, GTX 595 Quadro 4000, 5000, 6000 Tesla C2050, C2070, C2075 Get the DirectX SDK and run DirectX Caps Viewer Download and install the June 2010 DirectX SDK. As part of that you now have the DirectX Capabilities Viewer utility (find it in your start menu by searching for "DirectX Caps Viewer", the filename is DXCapsViewer.exe). It will list all your devices (emulated, and real hardware ones) under the first node. Expand the hardware entries and then expand again the Direct3D 11 folder. If you see D3D_FEATURE_LEVEL_11_ under that, then your card supports feature level 11 which means it supports DirectCompute and C++ AMP. In the following screenshot of one of my old laptops, the card only goes to feature level 10. Run a utility from the web that just tells you! Of course, writing some C++ AMP code that enumerates accelerators and lists the ones that are capable is trivial. However that requires that you have redistributed the runtime, so a more broadly applicable approach is to use the DX APIs directly to enumerate the DX11 capable cards. That is exactly what the development lead for C++ AMP has done and he describes and shares that utility at this post. Comments about this post by Daniel Moth welcome at the original blog.

    Read the article

  • Artec TV18R Tuner not working :(

    - by Antillar Maximus
    Can somebody kindly help me setup my TV Tuner stick? Make and Model: Artec TV18R USB TV Tuner OS: Ubuntu 11.10 64bit Hardware: MSI MS1656-US (GX640 barebones): i5 580M, 2xIntel X25M SSDs, Radeon HD5850M,Realtek sound. Logs and messages: antillar@antillar-MS-1656:/usr/share/dvb/atsc$ [B][COLOR=Red]sudo lsusb[/COLOR][/B] Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 003: ID ffc0:001f Bus 002 Device 005: ID 05d8:8117 Ultima Electronics Corp. [/code][code]antillar@antillar-MS-1656:/usr/share/dvb/atsc$ So, it seems that the tuner is being detected, but the light on it does not turn on? Not sure what is going on? sudo lspci [sudo] password for antillar: 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 02) 00:01.0 PCI bridge: Intel Corporation Core Processor PCI Express x16 Root Port (rev 02) 00:1a.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 05) 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 05) 00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 05) 00:1c.2 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 3 (rev 05) 00:1c.4 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 5 (rev 05) 00:1d.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a5) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 4 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 05) 01:00.0 VGA compatible controller: ATI Technologies Inc Broadway PRO [Mobility Radeon HD 5800 Series] 01:00.1 Audio device: ATI Technologies Inc Juniper HDMI Audio [Radeon HD 5700 Series] 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) 04:00.0 FireWire (IEEE 1394): JMicron Technology Corp. IEEE 1394 Host Controller 04:00.1 System peripheral: JMicron Technology Corp. SD/MMC Host Controller 04:00.2 SD Host controller: JMicron Technology Corp. Standard SD Host Controller 04:00.3 System peripheral: JMicron Technology Corp. MS Host Controller 04:00.4 System peripheral: JMicron Technology Corp. xD Host Controller 05:00.0 Network controller: Intel Corporation Ultimate N WiFi Link 5300 ff:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 02) ff:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 02) ff:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 02) ff:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 02) ff:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 02) ff:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 02) antillar@antillar-MS-1656:/usr/share/dvb/atsc$ I have been searching for a solution to this all weekend without any luck. I remember reading that ehci_hcd is the problem, but I'm not sure if disabling it is a good idea. I don't want my USB ports to go back to v1.1. Thank you!

    Read the article

  • Sony Vaio E14 upgraded to Windows 8.1 has fan on full all the time

    - by dav_i
    Having a bit of a nightmare after upgrading to 8.1 - the fan is constantly on maximum. This question and other sources around the net suggest upgrading the AMD driver. I have upgraded both the graphics drivers as far as I can: AMD Radeon HD 7600M - v13.150.102.0 Intel HD Graphics 4000 - v10.18.10.3316 and I am still having the issue. I'm at a lost as to what to do now! Any help would be greatly appreciated. Update Upgrading the AMD Radeon HD 7600M Series driver to 13.152.1.1000 seems to have fixed the issue on startup - however, putting the laptop to sleep and resuming causes the fan to go full speed at all times again.

    Read the article

  • Windows 7 does not recognise second display output

    - by gilles27
    I've got a PC with dual BenQ G2222HDL monitors and an ATI Radeon HD 4650 video card. I've been running both monitors at 1920x1080 for some months now but last week the second monitor switched to a lower resolution and won't let me go back to 1920x1080. If I right click the Desktop and choose Screen Resolution from the menu, I get two items in the Display: drop down list BenQ G2222HDL D-SUB Display device on: VGA In the past 2 was always the same as 1. If I click Detect a third item appears Available display output on: ATI Radeon HD 4650 but if I use the Multiple displays: drop down list to use it says "No display detected" and then lets me choose from either "Connect anyway on S-Video" or "Connect anyway on Component", neither of which help. It seems like Windows 7 recognises the card is dual-head, and knows I have got two monitors, but can't link it all together. I have checked and all my drivers are up-to-date. Does anyone have any suggestions as to how I can get the second monitor working properly again?

    Read the article

  • no display on tv when connecting pc via hdmi in win7

    - by Kane
    The system of pc is win7 32bit, the video card is ATI 4670. The tv is philips 74xx series. And the monitor is Dell 19' that connect with pc via VGA. The tv can receive the singal and show the pictures when booting the pc(bios self checking, the logo of windows 7), however the tv says there is no signal after the win7 login window shows. I have installed the latest CCC and driver of ATI video card. Does anyone have idea for it?

    Read the article

  • Windows Color Calibrator Does Not Retain Color Settings

    - by Zian Choy
    When I try to calibrate the monitor using Windows 7's color calibrator, the monitor rejects changes to the color settings. For example, one of my monitors has a blueish tinge. If I click my mouse to tone down the blue and then let go of my mouse the monitor will go back to being blueish. At the moment, I am getting around the problem by using the color controls in the monitor's on screen displays. How can I get the color calibrator to work? Update: I tried checking the color settings in the ATI Radeon Catalyst Control Center and noticed that I can't do anything. The "Reactivate ATI color controls" button keeps flashing and any changes I try to make are discarded instantly.

    Read the article

  • Windows 7 does not recognise second display output [closed]

    - by gilles27
    I've got a PC with dual BenQ G2222HDL monitors and an ATI Radeon HD 4650 video card. I've been running both monitors at 1920x1080 for some months now but last week the second monitor switched to a lower resolution and won't let me go back to 1920x1080. If I right click the Desktop and choose Screen Resolution from the menu, I get two items in the Display: drop down list BenQ G2222HDL D-SUB Display device on: VGA In the past 2 was always the same as 1. If I click Detect a third item appears Available display output on: ATI Radeon HD 4650 but if I use the Multiple displays: drop down list to use it says "No display detected" and then lets me choose from either "Connect anyway on S-Video" or "Connect anyway on Component", neither of which help. It seems like Windows 7 recognises the card is dual-head, and knows I have got two monitors, but can't link it all together. I have checked and all my drivers are up-to-date. Does anyone have any suggestions as to how I can get the second monitor working properly again?

    Read the article

  • Inconsistent black levels in windows 7 media center

    - by James G
    I've got a HTPC running windows 7 64bit, hooked up to a Samsung LCD TV. My problem is different types of video are displaying different black levels on the TV. When I play a bluray through Arcsoft Total Media Theater I have to set the "HDMI Black Level" to "normal" in the TV picture options menu. When I play recorded TV through WMC I have to set it to "low" otherwise the black colors on the video are washed out and grey. Is there any way to configure the system so all videos are displayed with the same black level? The hdmi black level setting is deep in Samsung's menus so it's becoming a chore to keep switching it everytime I watch a different type of video. I'm using an ATI 4670 graphics card with HDMI output going straight to the TV. In the ATI catalyst control center I've got pixel format set to RGB 4:4:4 (Full RGB) since the TV wont allow me to change the HDMI black level if I choose one of the other settings.

    Read the article

  • GeForce 8800GT not even giving basic output

    - by Sam
    My Dad bought a GeForce 8800GT graphics card quite a long time ago now. It has never worked in his PC. Print out from a dxdiag: System Information Time of this report: 4/13/2010, 19:52:40 Machine name: USER-PC Operating System: Windows Vista™ Home Premium (6.0, Build 6001) Service Pack 1 (6001.vistasp1_gdr.091208-0542) Language: English (Regional Setting: English) System Manufacturer: To Be Filled By O.E.M. System Model: To Be Filled By O.E.M. BIOS: Default System BIOS Processor: Intel(R) Core(TM)2 Quad CPU Q6600 @ 2.40GHz (4 CPUs), ~2.3GHz Memory: 2046MB RAM Page File: 1045MB used, 3296MB available Windows Dir: C:\Windows DirectX Version: DirectX 10 DX Setup Parameters: Not found DxDiag Version: 6.00.6001.18000 32bit Unicode DxDiag Notes Display Tab 1: No problems found. Sound Tab 1: No problems found. Sound Tab 2: No problems found. Sound Tab 3: No problems found. Input Tab: No problems found. DirectX Debug Levels Direct3D: 0/4 (retail) DirectDraw: 0/4 (retail) DirectInput: 0/5 (retail) DirectMusic: 0/5 (retail) DirectPlay: 0/9 (retail) DirectSound: 0/5 (retail) DirectShow: 0/6 (retail) Display Devices Card name: ATI Radeon HD 2400 PRO Manufacturer: ATI Technologies Inc. Chip type: ATI Radeon Graphics Processor (0x94C3) DAC type: Internal DAC(400MHz) Device Key: Enum\PCI\VEN_1002&DEV_94C3&SUBSYS_00000000&REV_00 Display Memory: 1012 MB Dedicated Memory: 245 MB Shared Memory: 767 MB Current Mode: 1280 x 960 (32 bit) (75Hz) Monitor: Generic PnP Monitor Driver Name: atiumdag.dll,atiumdva.dat,atitmmxx.dll Driver Version: 7.14.0010.0523 (English) DDI Version: 10 Driver Attributes: Final Retail Driver Date/Size: 8/22/2007 02:43:14, 3021312 bytes That info is from the current card that is installed in it and has been installed since its purchase roughly 3-4 years ago. When I physically install the card I put it into a purple slot on the motherboard that the old card was in (if I go into the device manager and select properties on the current card it confirms that the slot is a "PCI Slot 16 (PCI bus 2, device 0, function 0)") and boot up the computer but get absolutely no output. The screen that we have registers that it is connected to something (by not displaying the screen it does when the cable is unplugged) but just remains blank, no output at all. I recently took the card to my University and one of my friends who is better with hardware issues than I am tried it in his system and it worked perfectly. No issues whatsoever. I do not have a spec list for his system but I could get one if you need it. If you need any more information on this issue I will be happy to supply you with it as I am starting to get very annoyed with this problem ^_^

    Read the article

  • Why does installing NVidia 9600GT graphics card, take 1GB of RAM away from Windows?

    - by Nick G
    Hi, I've changed graphics cards in my PC and now Windows 7 (32bit) is reporting that I have a whole gigabyte less physical RAM in my PC. Why is this? Firstly, the machine has 4GB of physical RAM. The old card was an ATI 2600XT with 256MB and the new card is an NVidia 9600GT with 512MB. With the ATI card windows sees 3326MB. With the NVidia card, windows sees 2558MB. I realise that due to address space restrictions I will not see all 4GB with 32bit windows, but why is there such a massive loss of RAM when simply changing cards (bearing in mind BOTH cards have their own RAM and borrow no main memory like some built on chipsets do). Would using 64 bit windows solve this? Thanks Nick.

    Read the article

  • Building a new PC, Installing XP, blue screen of death

    - by Tim
    I got a gigabyte barebones kit and am installing windows-XP(SP1) and the initial setup works, then it restarts and goes into the second phase of the setup. Then when installing components (I think that's what it says) it gets half way done and comes up with a blue screen saying IRQL_NOT_LESS_OR_EQUAL. BUT! I had gotten past that by installing windows-XP media center addition Now I am trying to install the drivers for my Asus ATI Radeon 5770 graphics card and I get another blue screen of death that doesnt give much info something about address x0000005. Would you think there is something wrong with something in my system or do you think if I got windows 7 that would take care of things? Sorry for probably not giving enough info. Here is what I have MotherBoard - Gigabyte S-series GA-H55M-S2(v) PSU - Ultra 500 watt atx HDD - Sata serial ATA Seagate Baracudda 7200 CPU - Intel i3 Memory - 4gig crucial Graphics Card - Asus ATI Radeon 5770 1Gig DDR5

    Read the article

  • HP Envy 14, Ubuntu 10.10 and trouble with the graphics cards

    - by Carsten Gehling
    A few days ago I bought a HP Envy 14, containing 2 graphics card: An integrated Intel graphics card, and an ATI HD 5650. I've installed Ubuntu 10.10 32-bit on the machine. Most things work fine out of the box, but the graphics cards are giving me trouble. When booting, I get the message "failed to get i915 symbols, graphics turbo disabled". Then the screen blanks out during the remaining boot period. I am able to get the display working by changing to one of the consoles, then closing and opening the laptop's lid. It seems that Ubuntu gets confused about which card to use. I've read here: http://www.andreas-demmer.de/en/2010/07/18/testbericht-linux-auf-dem-hp-envy-14 that I should be able to turn off one the cards by echoing keywords into /sys/kernel/debug/vgaswitcheroo/switch, but that path is not available on my system. The BIOS does not have any methods to switch of the ATI card. Help anyone? /Carsten

    Read the article

  • HP Envy 14, Ubuntu 10.10 and trouble with the graphics cards

    - by Carsten Gehling
    A few days ago I bought a HP Envy 14, containing 2 graphics card: An integrated Intel graphics card, and an ATI HD 5650. I've installed Ubuntu 10.10 32-bit on the machine. Most things work fine out of the box, but the graphics cards are giving me trouble. When booting, I get the message "failed to get i915 symbols, graphics turbo disabled". Then the screen blanks out during the remaining boot period. I am able to get the display working by changing to one of the consoles, then closing and opening the laptop's lid. It seems that Ubuntu gets confused about which card to use. I've read here: http://www.andreas-demmer.de/en/2010/07/18/testbericht-linux-auf-dem-hp-envy-14 that I should be able to turn off one the cards by echoing keywords into /sys/kernel/debug/vgaswitcheroo/switch, but that path is not available on my system. The BIOS does not have any methods to switch of the ATI card. Help anyone? /Carsten

    Read the article

  • New monitor connected to HDMI adaptor doesn't show output after booting

    - by Paul
    Hello out there in the multiple monitors’ world. I am a very old newbie in your world and need help. I just purchased a new Asus VH236H monitor and hooked it up the HDMI port of an ATI Radeon HD4300 / 4500 Series display adaptor. I left the old Princeton LCD19 (TMDS) hooked up to the DVI port of the same display adaptor. Both monitors displayed the boot sequence, after I fired good old Sarastro2 (Asus P5Q Pro Turbo – Dual Core E5300 – 2.60 GHz) up. The Asus lacked one half of a second behind the Princeton until the Windows 7 Ultimate SP 1 boot up was complete. Then the Asus displayed “HDMI NO SIGNAL” and went into hibernation. The Princeton stayed lit up as before. Both monitors are displayed on the “Screen Resolution Setup Display” and I plaid around with them for a while. The only thing I accomplished was to shove the desktop icons from the Princeton to the still hibernating Asus. The “Multiple displays:” is set to “Extend these displays”, the Orientation is “Landscape” and the Resolutions are set on both to the “recommended” one. Both monitors show that they work properly in the advanced Properties display. What am I doing wrong, what am I missing? Never mind the opinions about the different resolutions of the two monitors. I always can unhook the Princeton and give it to a Goodwill Store if I do not like the setup. I just would like to make it work. Any constructive help is very much appreciated, Thank you. Thank you Anees Bakrain Only the ATI Radeon HD 4300/4500 Series adapter is displayed in the Device Manager, for that reason I have to assume that the onboard display adaptor is not active. All 40 drivers of Sarastro2 are up to date and the HDMI cable can not be the problem because both monitors displayed the boot sequence up to the moment when Windows 7 was loaded completely. This was the moment, when the Asus monitor lost its signal. Both connectors, HDMI and DVI are connected and removing the DVI connector would not solve my problem of running both monitors simultaneously. However, your suggestions shifted my seventy one year old brain into the next gear. The only question remaining is; “Why the signals to the Asus monitor stop after the sequence is complete”. The ATI Radeon HD 4300/4500 Series adapter seems to be capable of sending simultaneous HDMI and DVI signals, what is done during the boot sequence. Why do the signals change after the boot sequence is complete is the key question or der springende Punkt? Is this a correct assumption slhck?

    Read the article

  • Ubuntu 10.04 not detecting multiple monitors

    - by razass
    I have 2 graphics cards, the output from the lspci: 01:00.0 VGA compatible controller: ATI Technologies Inc RV770 [Radeon HD 4850] 02:00.0 VGA compatible controller: ATI Technologies Inc RV710 [Radeon HD 4350] I have one monitor connected to the 4850 and 2 connected to the 4350. However when I go into System Preferences Monitors the only monitor shown is the one connected to the 4850. Is there something I need to enable for it to be able to use the other card? How do I get this to work. Thanks.

    Read the article

  • DVI to HDMI - displaying bad.

    - by TutorialPoint
    I currently have a computer with a ASUS EAH5770 (ATi Radeon HD 5770) 1GB GDDR5 video card, and 4GB ram, 2.6 GHZ i5 processor. I just switched from a DVI (the blue one) to an HDMI cable. (Bigben Flat cable HDMI 1.3c) I use a Samsung SyncMaster 2032 MW, which has a HDMI input. The weird thing is, that my screen is off-the-corner of the tv (so it's too wide) (1920x1080), and windows icons and text are not displaying well, though 1080p videos in YouTube are looking brilliant, just like pictures. So i think it has something to do with Windows. I already have the ATI Catalyst Control Center with the drivers i received with my video card. I do not currently know how to fix these problems. Do i have to reinstall Windows or so? Or is it (hopefully) easier?

    Read the article

  • Chipset GPU causes a massive slowdown

    - by zyboxenterprises
    My AMD Radeon HD 7700 recently broke (fan stopped working and GPU overheated), and now I'm running on internal chipset graphics, and it causes a massive slowdown of the whole PC. I've changed the graphics memory from 32MB (minimum) to 256MB (highest), and it hasn't made any difference whatsoever. I'm using Windows Aero, and disabling it should have made a small difference, but it didn't; the whole PC is still slow. I know that it's not the computer build, because I built it myself, and it was a lot faster when it had the AMD Radeon HD 7700 in it, which is the reason why I believe it's the internal chipset graphics that are causing the problem. Is this behavior normal? I don't have the cash right now to go out and buy a new dedicated GPU. I'm using an ASRock N68C-GS FX motherboard with an AMD FX 4100 (overclocked to 4.3GHZ), with 4GB RAM. The overclock was an attempt to resolve this issue, and it isn't related to this issue that the integrated graphics is causing a slowdown.

    Read the article

  • How do I hookup a dual video card Crossfire rig to a single monitor?

    - by Alexed
    I just received a new Alienware box preinstalled with two nice shiny ATI 6950 graphics cards. My goal is to use both of them to give me really good resolution and frame rate on my single monitor. There's zero documentation with the Alienware box and nothing I can find online. Do I just plug the monitor into one of the cards, and expect the two cards to do magic internally? The ATI Crossfire website indicates a need for an "external crossfirex connection cable". Do I need to buy one of these? If so, what kind of cable is it? The AMD Catalyst Control Center shows the second card as "Linked" but when I go to the AMD Overdrive section, the second card is at zero temperature, and clock, suggesting it's not actually doing anything. What do I need to do to make use of both cards? Is it something that doesn't kick in until I do something graphically intensive?

    Read the article

  • I have problem with pc. Random reboots with post hyper transport sync flood error

    - by user29867
    I have problem with my pc. Random reboots with post "hyper transport sync flood" error. It happens completely random. Most times i watch movie, some times when i play a game, even when i browse internet. My spec are as follow: MB ASUS M4A78-E CPU Phenom II 940 Sapphire Radeon hd4850 Vapor-X RAM OCZ DDR2 PC2-8500 kit 2x2GB PSU CM Real Power M520W CASE CM Centurion 590 Temps of MB, CPU and 4850 are in normal range. MB is hooter, around 60-70°C under load, Radeon 60-65°C under load (playing game for couple hours). CPU dos not past 50-55°C. So i think its not a cooling problem, CM case is pretty good, and have a lots of fans. I try with this memmory: TWIN2X4096-6400C5DHX same problem.

    Read the article

  • Xen VGA passthrough: is it possible to have dual GPU's with single monitor

    - by user489481
    I hate dual-booting between Windows when I want to play a game and Linux when I need to work. I don't fancy running Linux in a VM and Wine almost never works for me. So, I'm thinking about buying a new mainboard and CPU that is compatible with Xen's VGA passthrough and HVM virtualization. I want to be able to switch between the Linux Dom0 and Windows DomU with ease, but the problem is I need two GPU's and have only one monitor. Right now I have a nVidia GTX 260 in my PC, but I also have a Radeon 4850 sitting in my closet that I was going to sell. My question is, can I salvage the Radeon card to run the Dom0 and have the nVidia card run the DomU while having some kind of device/software to connect them a single monitor? Power supply and airflow issues aside. If not, what would you suggest? Is this even possible?

    Read the article

  • Broadcom Corporation NetLink BCM57785 Gigabit Ethernet PCIe driver tg3 will not install?

    - by Pete
    aries@aries-laptop:~$ sudo ifconfig eth0 up eth0: ERROR while getting interface flags: No such device aries@aries-laptop:~$ lspci -nn 00:00.0 Host bridge [0600]: Advanced Micro Devices [AMD] Device [1022:1705] 00:01.0 VGA compatible controller [0300]: ATI Technologies Inc Device [1002:9641] 00:01.1 Audio device [0403]: ATI Technologies Inc Device [1002:1714] 00:04.0 PCI bridge [0604]: Advanced Micro Devices [AMD] Device [1022:1709] 00:06.0 PCI bridge [0604]: Advanced Micro Devices [AMD] Device [1022:170b] 00:11.0 SATA controller [0106]: Advanced Micro Devices [AMD] Device [1022:7800] (rev 40) 00:12.0 USB Controller [0c03]: Advanced Micro Devices [AMD] Device [1022:7807] (rev 11) 00:12.2 USB Controller [0c03]: Advanced Micro Devices [AMD] Device [1022:7808] (rev 11) 00:13.0 USB Controller [0c03]: Advanced Micro Devices [AMD] Device [1022:7807] (rev 11) 00:13.2 USB Controller [0c03]: Advanced Micro Devices [AMD] Device [1022:7808] (rev 11) 00:14.0 SMBus [0c05]: Advanced Micro Devices [AMD] Device [1022:780b] (rev 13) 00:14.2 Audio device [0403]: Advanced Micro Devices [AMD] Device [1022:780d] (rev 01) 00:14.3 ISA bridge [0601]: Advanced Micro Devices [AMD] Device [1022:780e] (rev 11) 00:14.4 PCI bridge [0604]: Advanced Micro Devices [AMD] Device [1022:780f] (rev 40) 00:16.0 USB Controller [0c03]: Advanced Micro Devices [AMD] Device [1022:7807] (rev 11) 00:16.2 USB Controller [0c03]: Advanced Micro Devices [AMD] Device [1022:7808] (rev 11) 00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] Device [1022:1700] (rev 43) 00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] Device [1022:1701] 00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] Device [1022:1702] 00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] Device [1022:1703] 00:18.4 Host bridge [0600]: Advanced Micro Devices [AMD] Device [1022:1704] 00:18.5 Host bridge [0600]: Advanced Micro Devices [AMD] Device [1022:1718] 00:18.6 Host bridge [0600]: Advanced Micro Devices [AMD] Device [1022:1716] 00:18.7 Host bridge [0600]: Advanced Micro Devices [AMD] Device [1022:1719] 01:00.0 Ethernet controller [0200]: Broadcom Corporation NetLink BCM57785 Gigabit Ethernet PCIe [14e4:16b5] (rev 10) 01:00.1 SD Host controller [0805]: Broadcom Corporation Device [14e4:16bc] (rev 10) 01:00.2 System peripheral [0880]: Broadcom Corporation Device [14e4:16be] (rev 10) 01:00.3 System peripheral [0880]: Broadcom Corporation Device [14e4:16bf] (rev 10) 02:00.0 Network controller [0280]: Broadcom Corporation Device [14e4:4358]

    Read the article

  • Why can't I run Compiz?

    - by jasoncruz98
    I installed Ubuntu 11.10 on my laptop. The main reason I switched to Ubuntu is because I wanted to use Compiz. The first thing I did was to go to Additional Drivers and install ATI/AMD Proprietary FGRLX Graphics Driver. There was also another one available, ATI/AMD Proprietary FGRLX Graphics Driver (post-release updates), but I didn't install that one, because it basically meant the same thing to me as the one I already installed. Next, I went to the ubuntuguide.org Oneiric Wiki http://ubuntuguide.org/wiki/Ubuntu:Oneiric#Compiz_Fusion So I followed the instructions there and ran this command in terminal: sudo apt-get install compiz compizconfig-settings-manager compiz-fusion-plugins-main compiz-fusion-plugins-extra emerald librsvg2-common But then, the terminal window said that the package "emerald" could not be found. So, I ran this command instead: sudo apt-get install compiz compizconfig-settings-manager compiz-fusion-plugins-main compiz-fusion-plugins-extra After that, I installed Fusion Icon by running this command: sudo apt-get install fusion-icon I restarted my computer, searched for Compiz Config Settings Manager, and clicked on it. Then, I activated Wobbly Windows. I logged off and logged back on again, but there was no wobbly windows effect. So I tried clicking on Fusion Icon, but it never started. Can someone please tell me what I did wrong here? Because I see everyone seems to be able to run Compiz except me. I really need to start Compiz, or else I think I'm going to uninstall Ubuntu.

    Read the article

  • Low-level GPU code and Shader Compilation

    - by ktodisco
    Bear with me, because I will raise several questions at once. I still feel, though, that overall this can be treated as one question that may be answered succinctly. I recently dove into solidifying my understanding of the assembly language, low-level memory operations, CPU structure, and program optimizations. This also sparked my interest in how higher-level shading languages, GLSL and HLSL in particular, are compiled and optimized, as well as what formats they are reduced to before machine code is generated (assuming they are not converted directly into machine code). After a bit of research into this, the best resource I've found is this presentation from ATI about the compilation of and optimizations for HLSL. I also found sample ARB assembly code. This sort of addressed my original curiosity, but it raised several other questions. The assembler code in the ATI presentation seems like it contains instructions specifically targeted for the GPU, but is this merely a hypothetical example created for the purpose of conceptual understanding, or is this code really generated during shader compilation? If so, is it possible to inspect it, or even write it in place of the higher-level syntax? My initial searches for an answer to the last question tell me that this may be disallowed, but I have not dug too deep yet. Also, along the same lines, are GLSL shader programs compiled into ARB assembly code before machine code is generated, and is it possible to write direct ARB assembly? Lastly, and perhaps what I am most interested in finding out: are there comprehensive resources on shader compilation and low-level GPU code? I have been unable to find any thus far. I ask simply because I am curious :)

    Read the article

< Previous Page | 25 26 27 28 29 30 31 32 33 34 35 36  | Next Page >