Search Results

Search found 1489 results on 60 pages for 'brian harrison'.

Page 24/60 | < Previous Page | 20 21 22 23 24 25 26 27 28 29 30 31  | Next Page >

• Cisco 678 Will Not Work using PPPoE - Possibly Because I Configured it Incorrectly..?

  - by Brian Stinar

  I am attempting to configure a Cisco 678 because I am totally sick on my Actiontec. However, I am running into some problems. It seems as though the Cisco is able to train the line, but I am unable to ping out. I am all right at programming, but still learning a lot when it comes to being a system administrator. I apologize in advance if I did something ridiculous, or am attempting to configure this device to do something it was not designed to do. It is almost like I am not correctly configuring the device to grab it's IP using PPPoA (like my Actiontec.) The output from "show running" (below) makes me think this too. Below are the commands I ran in order to configure this: # en # set nvram erase # write # reboot # en # set nat enable # set dhcp server enable # set PPP wan0-0 ipcp 0.0.0.0 # set ppp wan0-0 dns 0.0.0.0 # set PPP wan0-0 login xxxxx // My actual login # set PPP wan0-0 password yyyyy // My actual password # set PPP restart enabled # set int wan0-0 close # set int wan0-0 vpi 0 # set int wan0-0 vci 32 # set int wan0-0 open # write # reboot Here is the output from a few commands I thought could provide some useful information: cbos#ping 74.125.224.113 Sending 1 8 byte ping(s) to 74.125.224.113 every 2 second(s) Request timed out cbos#show version Cisco Broadband Operating System CBOS (tm) 678 Software (C678-I-M), Version v2.4.9 - Release Software Copyright (c) 1986-2001 by cisco Systems, Inc. Compiled Nov 17 2004 15:26:29 DMT FULL firmware version G96 NVRAM image at 0x1030f000 cbos#show errors - Current Error Messages - ## Ticks Module Level Message 0 000:00:00:00 PPP Info IPCP Open Event on wan0-0 1 000:00:00:14 ATM Info Wan0 Up 2 000:00:00:14 PPP Info PPP Up Event on wan0-0 3 000:00:01:54 PPP Info PPP Down Event on wan0-0 Total Number of Error Messages: 4 cbos#show interface wan0 wan0 ADSL Physical Port Line Trained Actual Configuration: Overhead Framing: 3 Trellis Coding: Enabled Standard Compliance: T1.413 Downstream Data Rate: 1184 Kbps Upstream Data Rate: 928 Kbps Interleave S Downstream: 4 Interleave D Downstream: 16 Interleave R Downstream: 16 Interleave S Upstream: 4 Interleave D Upstream: 8 Interleave R Upstream: 16 Modem Microcode: G96 DSP version: 0 Operating State: Showtime/Data Mode Configured: Echo Cancellation: Disabled Overhead Framing: 3 Coding Gain: Auto TX Power Attenuation: 0dB Trellis Coding: Enabled Bit Swapping: Disabled Standard Compliance: T1.413 Remote Standard Compliance: T1.413 Tx Start Bin: 0x6 Tx End Bin: 0x1f Data Interface: Utopia L1 Status: Local SNR Margin: 19.0dB Local Coding Gain: 7.5dB Local Transmit Power: 12.5dB Local Attenuation: 46.0dB Remote Attenuation: 31.0dB Local Counters: Interleaved RS Corrected Bytes: 0 Interleaved Symbols with CRC Errors: 2 No Cell Delineation Interleaved: 0 Out of Cell Delineation Interleaved: 0 Header Error Check Counter Interleaved: 0 Count of Severely Errored Frames: 0 Count of Loss of Signal Frames: 0 Remote Counters: Interleaved RS Corrected Bytes: 0 Interleaved Symbols with CRC Errors: 1 No Cell Delineation Interleaved: 0 Header Error Check Counter Interleaved: 0 Count of Severely Errored Frames: 0 Count of Loss of Signal Frames: 0 cbos#show int wan0-0 WAN0-0 ATM Logical Port PVC (VPI 0, VCI 32) is configured. ScalaRate set to Auto AAL 5 UBR Traffic IP Port Enabled cbos#show running Warning: traffic may pause while NVRAM is being accessed [[ CBOS = Section Start ]] NSOS MD5 Enable Password = XXXX NSOS MD5 Root Password = XXXX NSOS MD5 Commander Password = XXXX [[ PPP Device Driver = Section Start ]] PPP Port User Name = 00, "XXXX" PPP Port User Password = 00, XXXX PPP Port Option = 00, IPCP,IP Address,3,Auto,Negotiation Not Required,Negotiable ,IP,0.0.0.0 PPP Port Option = 00, IPCP,Primary DNS Server,129,Auto,Negotiation Not Required, Negotiable,IP,0.0.0.0 PPP Port Option = 00, IPCP,Secondary DNS Server,131,Auto,Negotiation Not Require d,Negotiable,IP,0.0.0.0 [[ ATM WAN Device Driver = Section Start ]] ATM WAN Virtual Connection Parms = 00, 0, 32, 0 [[ DHCP = Section Start ]] DHCP Server = enabled [[ IP Routing = Section Start ]] IP NAT = enabled [[ WEB = Section Start ]] WEB = enabled cbos# wtf...? Thank you all very much for taking the time to read this, and the help.

  Read the article

• Multiple Copies of Windows Calculator

  - by Brian Boatright

  Just did a clean install of Win7 x64. I have a Microsoft Ergo Keyboard 4000 and use the calculator key a lot. Previously I could hit it and get multiple copies of calculator to popup. Now it will only show one copy of calculator. I tried adding a shortcut to the calculator app but it has the same limitation. However if I click the calculator icon it will open a new one each time. How can I fix this so each time I press the calculator key it will open a new copy?

  Read the article

• Windows XP install driver notification for AirCard

  - by Brian

  A co-worker of mine is using an air-card. It prompted him to install software in the notification tray, but he clicked on the wrong thing and the icon went away without him installing that software. How can I get that icon back? He can't install the software then. I know that you can download the software from the site, but we did that and were having issues from that too. Restarting and trying again doesn't pop up the notification either. Thanks.

  Read the article

• Can I use TCP as DNS query protocol on Mac OS?

  - by Brian

  Hi, I'm using Mac OS, Snow Leopard 10.6.2, and I'm suffering from UDP packet loss during DNS query. So I tried DNS query as TCP using dig command, it worked very well. However, I can't find some control switch to change to use TCP during DNS query. Is there a way to change it in Mac OS? Thank you.

  Read the article

• Can I use TCP as DNS query protocol on Mac OS?

  - by Brian

  Hi, I'm using Mac OS, Snow Leopard 10.6.2, and I'm suffering from UDP packet loss during DNS query. So my web browser is too slow to surf internet nicely. But it worked very well when I tried a DNS query on TCP using dig command. However, I can't find some control switch to change to use TCP during DNS query. Is there a way to change it in Mac OS? Thank you.

  Read the article

• Apache Configuration Issue - website without www going to default site

  - by Brian

  I have included a copy of my virtual host file for apache below. (However I have hidden the ip address and domain name for now) My problem is that the following work: www.mydomainnamehere.org www.mydomainnamehere.com mydomainnamehere.com This one doesn't work: mydomainnamehere.org - instead of going to the document root listed below, it goes to the document root of the default site. What could be causing this? <VirtualHost [ipaddresshidden]:80> ServerAdmin [email protected] ServerName mydomainnamehere.org ServerAlias www.mydomainnamehere.org ServerAlias mydomainnamehere.com ServerAlias www.mydomainnamehere.com DocumentRoot /home/www/mydomainnamehere.org/html/ ErrorLog /home/www/mydomainnamehere.org/logs/error.log CustomLog /home/www/mydomainnamehere.org/logs/access.log combined </VirtualHost>

  Read the article

• Windows 7 hangs after going into sleep a second time

  - by Brian Stephenson

  I've searched everywhere around Google and can't figure out why this is happening so I decide to ask here to see if anyone has a problem like this. Like it says in the title, whenever I sleep ONCE I'm able to wake the system, but going back to sleep again AFTER waking up for the first time results in it hanging on no input and no output, with the fan spinning as fast as possible and alot of heat being spewed out by the fan as well. I've tried various things like setting all USB Hub Root's to not get switched off for power saving, disabling USB selective suspend, disabling PCI-e link state power management, and even unplugging ALL USB devices and it wont wake up after the second attempt. And I've even waited up to a full hour of the CPU fan spinning loudly and it's still stuck trying to wake up. The only USB devices I use are a Microsoft USB Comfort Curve Keyboard 2000 (IntelliType Pro) and a generic HID compliant mouse from Creative model number OMC90S "CREATIVE MOUSE OPTICAL LITE". My other devices like external drives and controllers are unplugged when I'm not using them as having too many USB devices plugged in at a time causes a deadlock on almost all of the ports I have. Here's my system specifications (Most of these are from CPU-Z): Brand: Gateway DX4300-19 Mainboard: Gateway RS780 Chipset: AMD 780G Rev 00 Southbridge: AMD SB700 Rev 00 LPCIO: ITE IT8718 BIOS: American Megatrends Inc. ver P01-A4 09/15/2009 CPU: AMD Phenom II X4 810 at 2.60 GHz RAM: 8.0 GB DDR2 Dual Channel Ganged Mode at 400 MHz GPU: ATI Radeon HD3200 Graphics Intergrated - RS780 OS: Windows 7 Home Premium x64 OEM (Acer Group) HDD: WDC WD10EADS-22M2B0 1.0 TB (Western Digital Green Caviar) My BIOS has absolutely no control over how I setup the sleep mode to be either S1 or S3. So I can't check these settings or even change them. Hybrid sleep is also disabled, I can successfully go into hibernation and wake from hibernation but this is painfully slow due to a harddrive problem I'm having with this "Green Drive". (Hibernation takes over ~3 minutes to complete) Any help would be appreciated, thanks.

  Read the article

• nginx proxy pass redirect through load balancer

  - by Brian

  I have several backend webservers that are load-balanced using LVS. These machines have only internal non-routable IPs on them. The load-balancer is the only machine with an external IP. This setup works great. I would like to add another webserver for image serving, but it will not be part of the load-balanced pool. Is it possible to proxy pass from the load-balanced web servers to the image server and have the response redirected to the client? Client--external LB--internal web server--internal image server I've gotten proxy pass working when I remove the LB from the equation, but no luck when trying to use it.

  Read the article

• Is this video card good for 3 monitors? [on hold]

  - by Brian Briu

  Video card: http://www.amazon.de/Zotac-NVIDIA-GeForce-Grafikkarte-Speicher/dp/B00D4KCSHG/ref=sr_1_11?ie=UTF8&qid=1408575042&sr=8-11&keywords=grafikkarte 3 Monitors like this: http://www.mediamarkt.de/mcs/product/ASUS-MX-239-H,48353,462790,951629.html?langId=-3 If yes how can I connect them? If no, i'll buy one more video card like that. Also tell me what motherboard should I buy for these things + 32 ram and i7 (remember that in the future i'll buy one morre video card (to have 2). Power supply also?

  Read the article

• XP Install Driver Notification for AirCard

  - by Brian

  Hello, A co-worker of mine is using an air-card; it prompted him to install software in the notification tray; he clicked on the wrong thing and the icon went away without him installing that software. How can I get that icon back? He can't install the software then... I know that you can download the software from the site, but we did that and were having issues from that too, was hoping to be able to install the sofware on the air card... Restarting and trying again doesn't pop up the notification too. Thanks.

  Read the article

• Is there a way to tell if a program like KeyScrambler is first in the list of keyboard driver filter

  - by Brian T Hannan

  I recently found a program called KeyScrambler which appears to be a keyboard driver filter that intercepts keystrokes and jumbles them up for you so keyloggers aren't able to get your keystrokes while visiting your online banking sites. I was wondering if there is a way to tell if KeyScrambler is always first in line for the keyboard driver filters or if another driver filter could be installed and intercept the keystrokes before it gets to KeyScrambler.

  Read the article

• Does "From" field have to have the same domain as the reverse DNS to not be considered spam?

  - by Brian

  I have 2 applications at the same IP with 2 different domain names. Hourjar uses [email protected] for the "From" field when it sends emails, and Nimikri uses [email protected]. If my my reverse DNS points back to nimikri.com, will my message from [email protected] be marked as spam?

  Read the article

• Connect to MySQL EC2 Instance outside of VPC

  - by Brian W

  I have a VPC setup with a few EC2 instances inside. I'm attempting to connect to a MySQL database on an EC2 instance outside the VPC, with no luck. I have the security groups on the VPC EC2 instances set to outbound 0.0.0.0/0 which I assumed would let it connect to any outbound connection. I also followed a tutorial on creating a NAT, but wasn't exactly sure how to use it to connect to an external database. In any case, if anyone has experience and knows the proper way to connect to a database outside the VPC, it would be greatly appreciated!

  Read the article

• nginx proxy pass redirect through load balancer

  - by Brian

  I have several backend webservers that are load-balanced using LVS. These machines have only internal non-routable IPs on them. The load-balancer is the only machine with an external IP. This setup works great. I would like to add another webserver for image serving, but it will not be part of the load-balanced pool. Is it possible to proxy pass from the load-balanced web servers to the image server and have the response redirected to the client? Client--external LB--internal web server--internal image server I've gotten proxy pass working when I remove the LB from the equation, but no luck when trying to use it.

  Read the article

• Windows PE 3.0 detect what device it was booted from

  - by Brian

  I am creating a custom boot disk for work using Windows PE 3.0. I need to be able to tell what drive the system was booted from. it may be a CD, or a USB Flash drive. In the past, I have looked for a file on the root of the drive that holds some of our custom configuration. however that is getting a bit messy. Basically, in addition to Windows PE, the drive or disk also has other scripts and tools. I need to remount that USB drive or DVD to the U:\ Drive, to keep thing consistent. Basically, Diskpart.exe Select Volume $X assign Letter=U Exit I just need to figure out how to determine that nasty little $X.

  Read the article

• MySQL Server Not Starting on Boot

  - by Brian

  I have installed MySQL on a RHEL 5 server and I'm wanting to set it up so that the server starts on boot. I've ran the "chkconfig --list mysqld" command and it's currently running on levels 3, 4 and 5. However, when I reboot the server, no mysqld process is started. I've also tried manually starting the server by executing "/usr/bin/mysqld_safe" and I get the following output: Starting mysqld daemon with databases from /var/lib/mysql STOPPING server from pid file /var/run/mysqld/mysqld.pid 100319 10:31:30 mysqld ended I looked in /var/log/mysqld.log and I found the following: 100319 10:29:01 mysqld started 100319 10:29:02 InnoDB: Started; log sequence number 0 29752204 100319 10:29:02 [ERROR] Can't start server : Bind on unix socket: Permission denied 100319 10:29:02 [ERROR] Do you already have another mysqld server running on socket: /var/lib/mysql/mysql.sock ? 100319 10:29:02 [ERROR] Aborting

  Read the article

• Email error 'Default email client is not properly installed' after installing Bugzilla 3.6.3 on Windows Home Server 2011

  - by Brian Frost

  I have been using Bugzilla fine on the older 32-bit Windows Home Server and I have now started a migration to the newer Windows Home Server 2011 with a new machine and a fresh Bugzilla install of 3.6.3. All goes well until I try to check out the email action and I get 'Could not perform this operation because the defaulty mail client in not properly installed. Is this a security /firewall issue? I dont know enough about servers to know what to look for, so any help will be gratefully appreciated. Thanks.

  Read the article

• How do I turn a shared computer back into a shared media drive?

  - by Brian Green

  There is an external hard drive that is set up as a shared media device for a TV. I tried to hook up my the library on my desktop as a shared media drive to watch movies from my computer on the TV. It worked for a little bit but about 5 seconds after getting into my computer the tv went blank and I couldn't access the external hard drive any more. When I checked on my computer the Hard drive was no longer a shared media device but now it was a computer on the network. How do I fix this and turn it back into a shared media device so I can access it on the TV?

  Read the article

• Exchange 2010 Room Mailbox Calendar Permissions

  - by Brian Mitchell

  Exchange 2010 sp2 Outlook 2007/2010 Server 2008 I have managed to set up several room mailboxes in exchange, people are able to book the rooms and they get a response from the exchange server. this is brilliant. however users are unable to view the calendar of the room mailbox to see what times are available, in a ideal world I would like users to only see if the room is free or not. I dont want users to see the details of the meeting (title, description etc) I have been trying to do this using the following command Add-MailboxFolderPermission -Identity meetingroom -User "Usergroup" -AccessRights AvailabilityOnly -DomainController AD-Server This throws the following error Specified argument was out of the range of valid values. Parameter name: memberRights + CategoryInfo : NotSpecified: (meetingroom:MailboxFolderIdParameter) [Add-MailboxFolderPermission], Argum entOutOfRangeException + FullyQualifiedErrorId : CBC6516F,Microsoft.Exchange.Management.StoreTasks.AddMailboxFolderPermission Any help on the situation would be brilliant, i have been trying to get this done for a couple of days and im going around in circles.

  Read the article

• Large .tmp files in C:\Windows\Temp

  - by Brian

  I have a Windows 2008 server which functions as a web service server, and every other week or so, the C:\Windows\Temp folder is filled with large (between 40-300 meg) files with names like: ~DF5D73.tmp, ~DFA95.tmp, etc. They appear My webservices on the server don't create any files with that type of name, and the contents don't appear to help identify them. Process Explorer indicates that w3wp.exe is currently using several of the files, but I can't imagine specifically where they're coming from. As an example, the top of one of the files is: ÐÏࡱá > þÿ þÿÿÿ þÿÿÿ ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿýÿÿÿþÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿR o o t E n t r y ÿÿÿÿÿÿÿÿÿÿÿÿ þÿÿÿ ÿÿÿÿÿÿÿÿÿÿÿÿ ÿÿÿÿÿÿÿÿÿÿÿÿ ÿÿÿÿÿÿÿÿÿÿÿÿ BM¦h' 6 ( / ph' ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ The owner of the file is only identified as localname\Administrators, so that's no help. Anyone else experienced a similar issue or any suggestions to track where the files are coming from?

  Read the article

• Problems executing check_mysql plugin

  - by Brian

  I'm attempting to test out the check_mysql plugin for Nagios using the command line. It works great when I'm just checking localhost but when I try to specify a different server (using the -H argument) I keep getting the following error message: CRITICAL - Unable to connect to mysql://nagios_user@{remoteServerHostname}/ - Access denied for user 'nagios_user'@'{localServerHostName}' (using password: YES) It looks like it's trying to connect to the database using the localhost server even though I've specified a different host name. I've already set up this user on the remote database and they have correct permissions. I'm just trying to figure out why the script keeps inserting the localhost server name instead of the remote one.

  Read the article

• How do I set Internet Explorer 64-bit as my default browser?

  - by Brian Knoblauch

  Windows Vista x64. It defaults to IE 32-bit, and will not allow me to set 64-bit as the default with the "Make Default" button. I'm currently forced to workaround by starting IE 64-bit manually, and leaving it up with an empty window. Then when links are fired from apps, they open in that 64-bit version. Problem being is that sometimes I forget and get a bunch of stuff opened in 32-bit without realizing it. Then I have to remember all the links I clicked, close ALL of them, open IE 64-bit, and put them all back in. Trying to avoid all that re-work when I forget to do the workaround. Unfortunately, all the forums I've googled that discuss this just have a bunch of people saying "don't do that" and "you don't want to do that". Yes, I do want to do this. The particular feature I use only works right in my 64-bit version, and I don't use 32-bit plugins. I fully understand the implications of what I'm doing. :-)

  Read the article

• OS X Automator empty, blank or null value.

  - by Brian

  I have some data files mostly excel, word and pdf files most of the files have no extension on them. So they are missing the .doc .xls. This data needs to be used in a Windows environment now. I have created automator apps for each of the file types I want to add the ext onto. The problem is it also adds the extension to files that already have an extension. So data.xls becomes data.xls.xls I would like to figure a way to only add the extenion to the files without extension. How do I tell the finder filter that i only want it to return files without extensions. I see how to add a line to filter by extension but I don't know how to let it know I want only blank or null or files without any extensions. Thanks

  Read the article

• How do I enable additional debugging output from Ansible and Vagrant?

  - by Brian Lyttle

  I'm investigating Ansible for server and application provisioning. My application is currently provisioned with shell scripts in Vagrant. Rather than rewrite my scripts I've taken a sample and attempted to deploy it. It appears to deploy fine, but I've seeing a failure message after what looks like a series of successful steps: » vagrant provision ~/vm/blvagrant 1 ? [default] Running provisioner: ansible... PLAY [web-servers] ************************************************************ GATHERING FACTS *************************************************************** ok: [192.168.9.149] TASK: [install python-software-properties] ************************************ ok: [192.168.9.149] => {"changed": false, "item": ""} TASK: [add nginx ppa if it ubuntu 10.04 and up] ******************************* ok: [192.168.9.149] => {"changed": false, "item": "", "repo": "ppa:nginx/stable", "state": "present"} TASK: [update apt repo] ******************************************************* ok: [192.168.9.149] => {"changed": false, "item": ""} TASK: [install nginx] ********************************************************* ok: [192.168.9.149] => {"changed": false, "item": ""} TASK: [copy fixed init for nginx] ********************************************* ok: [192.168.9.149] => {"changed": false, "gid": 0, "group": "root", "item": "", "mode": "0755", "owner": "root", "path": "/etc/init.d/nginx", "size": 2321, "state": "file", "uid": 0} TASK: [service nginx] ********************************************************* ok: [192.168.9.149] => {"changed": false, "item": "", "name": "nginx", "state": "started"} TASK: [write nginx.conf] ****************************************************** ok: [192.168.9.149] => {"changed": false, "gid": 0, "group": "root", "item": "", "mode": "0644", "owner": "root", "path": "/etc/nginx/nginx.conf", "size": 1067, "state": "file", "uid": 0} PLAY RECAP ******************************************************************** 192.168.9.149 : ok=8 changed=0 unreachable=0 failed=0 Ansible failed to complete successfully. Any error output should be visible above. Please fix these errors and try again. How do I go about getting additional debug information? I've already added ansible.verbose = true to my vagrant config which results in the dictionaries being displayed within the output above.

  Read the article

• IIS 6 Compression for a folder

  - by Brian

  Hello, I want to enable IIS 6 compression for all of the folders in my application except one; in this one folder, I do some things that fails when IIS 6 compression is enabled... Any advice? Thanks.

  Read the article

< Previous Page | 20 21 22 23 24 25 26 27 28 29 30 31  | Next Page >