Search Results

Search found 33971 results on 1359 pages for 'ask and learn'.

Page 240/1359 | < Previous Page | 236 237 238 239 240 241 242 243 244 245 246 247  | Next Page >

• xorg, nvidia, log-in all hosed - how can I completely reset graphics set-up/settings?

  - by Fred Hamilton

  I just did a fresh install of Mythbuntu 12.04.1 on my Intel MB with nVidia 9500GT graphics card. Hardware's been working great with 10.10 for about 2 years. Background: (optional - feel free to skip to question) I was trying to get my component video output to generate 720p, messing around with the nvidia drivers, and now the entire display system is hosed. I can SSH in and get a terminal. Depending on which nvidia package I install/remove, I get: Garbage on screen (after I "apt-get remove nvidia*") A low-res graphical log-in screen where I can log in as fred or guest. If I log in as fred, it displays some text mode status line then goes right back to the log-in screen. If I log in as guest, I actually get the full Ubuntu desktop, but I need to be able to log in as fred. Other times I get an error: "API mismatch: the NVIDIA kernel module has version 304.43, but this NVIDIA driver component has version 295.49." I've googled around, including trying this thread with the same error message, but to no effect. Question: How can I just reset x settings, drivers, everything display-related to the exact same way it was after a fresh install?

  Read the article

• I can't get over a resolution of 640x480 after upgrading to 12.04, how can I fix it?

  - by Sandeep Srivastava

  Ever since I upgraded to 12.04 my screen resolution has gone down to 640 x 480, even though I had higher resolutions before. My xrand output looks as below : sandeep@sandeep-desktop:~$ xrandr xrandr: Failed to get size of gamma for output default Screen 0: minimum 640 x 480, current 640 x 480, maximum 640 x 480 default connected 640x480+0+0 0mm x 0mm 640x480 0.0* How can I get higher resolutions, I know that my monitor support higher resolutions.

  Read the article

• Execute command from file in current shell

  - by Pandya

  I want to executed command from file (which is script) in current shell in terminal. Example: I have file ch_dir contains following: #!/bin/bash cd /usr Now if I execute file usually as following then it executes commands in different shell: pandya@pandya-desktop:~$ ./ch_dir pandya@pandya-desktop:~$ Here cd /user is executed in different shell. But I want to execute in Current shell. How do I do that? Note: Here cd is only used to explain. Question's aim is to execute any command in current shell

  Read the article

• Force apt to remove all emacs*

  - by wishi

  Hi! I have a bug-problem with the apt-packages of emacs: >>Error occurred processing debian-ispell.el: File error (("Opening input file" "no such file or directory" "/usr/share/emacs23/site-lisp/dictionaries-common/debian-ispell.el")) >>Error occurred processing ispell.el: File error (("Opening input file" "no such file or directory" "/usr/share/emacs23/site-lisp/dictionaries-common/ispell.el")) >>Error occurred processing flyspell.el: File error (("Opening input file" "no such file or directory" "/usr/share/emacs23/site-lisp/dictionaries-common/flyspell.el")) emacs-install: /usr/lib/emacsen-common/packages/install/dictionaries-common emacs23 failed at /usr/lib/emacsen-common/emacs-install line 28, <TSORT> line 30. dpkg: error processing emacs23-lucid (--configure): subprocess installed post-installation script returned error exit status 1 dpkg: dependency problems prevent configuration of emacs: emacs depends on emacs23 | emacs23-lucid | emacs23-nox; however: Package emacs23 is not installed. Package emacs23-lucid which provides emacs23 is not configured yet. Package emacs23-nox which provides emacs23 is not installed. Package emacs23-lucid is not configured yet. Package emacs23-nox is not installed. dpkg: error processing emacs (--configure): dependency problems - leaving unconfigured No apport report written because the error message indicates its a followup error from a previous failure. Errors were encountered while processing: emacs23-lucid emacs E: Sub-process /usr/bin/dpkg returned an error code (1) In fact I would be satisfied with just emacs23-nox, a couple of plugins - from apt. But I can neither --purge nor --purge reinstall, nor remove the packages. It always processes until this certain bug. I did some google-searching, found some stuff on Launchpad suggesting: sudo apt-get install --reinstall --purge emacsen-common But this is the same... so I hope there a way to tell app to just remove everything releated to emacs, and to start from scratch again? Thanks, Marius

  Read the article

• sound card is not working

  - by ralph crowhurst

  I've installed Ubuntu 11.4 on my dell xps m2010 using wubi. Then booted up and could not connect to the Internet using 3three huawei e122 usb mobile broadband (I would like this to work also). I've managed to connect through a wireless network, I went to my favorite sites and was told I needed to install adobe flash player.This what I did players run and picture is good. But there is no sound! Then I've tried to play songs in Banshee, but no sound. I have checked everything in sound preferences including test speaker, there is sound. I have sigmatel sound card. Thanks

  Read the article

• Ubuntu 12.10 boots to purple or black screen but intermittently boots fine

  - by Nic

  I have a fresh install of Ubuntu 12.10 64bit dual booting with Win7 64bit. Windows boots fine every time. When I choose Ubuntu from Grub2 menu it will sometimes boot just fine. Most of the times though it gets stuck at a purple screen with nothing happening and no keys or key combinations working. Other times instead of the purple screen I get a black screen with a flashing cursor at the top. Nothing happens. I need to hold down the power button to restart and after a couple times of trying it will eventually boot into Ubuntu. Once that happens everything runs without any problems. I have tried different approaches to fix the problem but to no avail. I tried removing "quiet splash", used no splash, and nomodeset What I got from this was seeing all the text of the boot process but more often than not the process gets stuck right after recognizing all the USB ports and devices. If it gets stuck nothing happens (except when i plug in a usb device: it still recognizes it with a new line of text) In the case when the boot process works, after it lists the usb devices it tells me something like: recovery of read-only filesystem necessary. (its the filesystem that ubuntu runs on) then it does the recovery and i get: recovery complete. after that Ubuntu will boot properly and I get to see the login screen. I have no idea what to do to fix that problem. I have to reboot 3 to 5 times everytime I want to get into Ubuntu and I feel like I'm breaking my new Laptop. (its a lenovo ideapad z580 btw. i5 processor and nvidia gtx640 graphics card) I hope someone can help me. Thanks. Edit: i just got a "failed to enable AA error" message when waking it up from suspend. I don't know if that helps or has anything to do with the boot probs.

  Read the article

• Building ATLAS (and later Octave w/ ATLAS)

  - by David Parks

  I'm trying to set up ATLAS (so I can later compile octave with ATLAS support). If I'm correct, I still need to build this manually due to the environment specific optimizations. I do see a package for ATLAS, but it looks like it's using the cross platform generic build options (e.g. "it'll be slow"). So, running the configure script as described in the docs seems to go poorly. As a java developer I never do well at making heads or tails of errors in these build processes. Am I missing dependencies (if so is there any documentation on what I need)? allusers@vbubuntu:~/Downloads/atlas3.10.1/build_vbubuntu$ ../configure -b 64 -D c -DPentiumCPS=3000 --with-netlib-lapack-tarfile=/home/allusers/Downloads/lapack-3.5.0.tgz make: `xconfig' is up to date. ./xconfig -d s /home/allusers/Downloads/atlas3.10.1/build_vbubuntu/../ -d b /home/allusers/Downloads/atlas3.10.1/build_vbubuntu -b 64 -D c -DPentiumCPS=3000 -Si lapackref 1 OS configured as Linux (1) Assembly configured as GAS_x8664 (2) Vector ISA Extension configured as SSE3 (6,448) ERROR: enum fam=3, chip=2, mach=0 make[3]: *** [atlas_run] Error 44 make[2]: *** [IRunArchInfo_x86] Error 2 Architecture configured as Corei1 (25) ERROR: enum fam=3, chip=2, mach=0 make[3]: *** [atlas_run] Error 44 make[2]: *** [IRunArchInfo_x86] Error 2 Clock rate configured as 2350Mhz ERROR: enum fam=3, chip=2, mach=0 make[3]: *** [atlas_run] Error 44 make[2]: *** [IRunArchInfo_x86] Error 2 Maximum number of threads configured as 4 Parallel make command configured as '$(MAKE) -j 4' ERROR: enum fam=3, chip=2, mach=0 make[3]: *** [atlas_run] Error 44 make[2]: *** [IRunArchInfo_x86] Error 2 Cannot detect CPU throttling. rm -f config1.out make atlas_run atldir=/home/allusers/Downloads/atlas3.10.1/build_vbubuntu exe=xprobe_comp redir=config1.out \ args="-v 0 -o atlconf.txt -O 1 -A 25 -Si nof77 0 -V 448 -b 64 -d b /home/allusers/Downloads/atlas3.10.1/build_vbubuntu" make[1]: Entering directory `/home/allusers/Downloads/atlas3.10.1/build_vbubuntu' cd /home/allusers/Downloads/atlas3.10.1/build_vbubuntu ; ./xprobe_comp -v 0 -o atlconf.txt -O 1 -A 25 -Si nof77 0 -V 448 -b 64 -d b /home/allusers/Downloads/atlas3.10.1/build_vbubuntu > config1.out make[2]: gfortran: Command not found make[2]: *** [IRunF77Comp] Error 127 make[2]: g77: Command not found make[2]: *** [IRunF77Comp] Error 127 make[2]: f77: Command not found make[2]: *** [IRunF77Comp] Error 127 Unable to find usable compiler for F77; abortingMake sure compilers are in your path, and specify good compilers to configure (see INSTALL.txt or 'configure --help' for details)make[1]: *** [atlas_run] Error 8 make[1]: Leaving directory `/home/allusers/Downloads/atlas3.10.1/build_vbubuntu' make: *** [IRun_comp] Error 2 ERROR 512 IN SYSCMND: 'make IRun_comp args="-v 0 -o atlconf.txt -O 1 -A 25 -Si nof77 0 -V 448 -b 64"' mkdir src bin tune interfaces mkdir: cannot create directory ‘src’: File exists mkdir: cannot create directory ‘bin’: File exists mkdir: cannot create directory ‘tune’: File exists mkdir: cannot create directory ‘interfaces’: File exists make: *** [make_subdirs] Error 1 make -f Make.top startup make[1]: Entering directory `/home/allusers/Downloads/atlas3.10.1/build_vbubuntu' Make.top:1: Make.inc: No such file or directory Make.top:325: warning: overriding commands for target `/AtlasTest' Make.top:76: warning: ignoring old commands for target `/AtlasTest' make[1]: *** No rule to make target `Make.inc'. Stop. make[1]: Leaving directory `/home/allusers/Downloads/atlas3.10.1/build_vbubuntu' make: *** [startup] Error 2 mv: cannot move ‘lapack-3.5.0’ to ‘../reference/lapack-3.5.0’: Directory not empty mv: cannot stat ‘lib/Makefile’: No such file or directory ../configure: 450: ../configure: cannot create lib/Makefile: Directory nonexistent ../configure: 451: ../configure: cannot create lib/Makefile: Directory nonexistent ../configure: 452: ../configure: cannot create lib/Makefile: Directory nonexistent ../configure: 453: ../configure: cannot create lib/Makefile: Directory nonexistent ../configure: 509: ../configure: cannot create lib/Makefile: Directory nonexistent DONE configure

  Read the article

• What is the significance of '*' (star, asterisk) in the file listing results?

  - by vfclists

  I have noticed that some of my files have an asterisk at end. Does the asterisk at the end have any particular significance? I think they are mostly executable and displayed in green by the ls command. You will see that ./bkmp* and ./bkmp0* have an asterisk at the end. They are executable bash scripts. Here's my output: drwxr-xr-x 7 username username 4096 Oct 2 18:28 ./ drwxr-xr-x 8 root root 4096 Oct 2 09:25 ../ -rw-r--r-- 1 username username 3724 Sep 22 03:06 .bashrc -rwxr--r-- 1 username username 319 Sep 22 03:42 .bkmp* -rwxr--r-- 1 username username 324 Sep 29 23:30 .bkmp0* drwx------ 2 username username 4096 Sep 17 13:52 .cache/ -rw-r--r-- 1 username username 675 Sep 17 13:37 .profile drwx------ 2 username username 4096 Sep 22 10:10 .ssh/ drwx------ 2 username username 4096 Sep 24 19:49 .ssh.local/ drwxr-xr-x 2 username username 4096 Sep 22 04:10 archives/ drwxr-xr-x 3 username username 4096 Sep 24 19:51 home/ -rw-r--r-- 1 username username 27511 Sep 24 19:51 username_backup.20120924_1908.tar.gz

  Read the article

• How do I install FreeNX server so that it works correctly?

  - by Niklas

  I've tried every single possible way of installing the server now, I've read every how to available and I still can't get it to work. Please let me know in which step I do wrong. I'm using ubuntu 10.10. I will mainly be referring to the following how-to, but also this, and this one. First I add the ppa Install Freenx Download the special Freenx package as stated in the howto, fix ownership - install it Create custom SSH key Copy the file /var/lib/nxserver/home/.ssh/client.id_dsa.key to the client and import it in nomachine (windows 7 x64) Check that both the user I will be logging in with and the user nx is in AllowedUsers in the /etc/ssh/sshd_config file Check the port that ssh is listening on Login through nomachine with my regular user account in ubuntu I always receive the message "authentication failed for [user]" when I try to log in. And I can't see the user "nx" which is said to be created during installation when I look under System-Administration-"Users & Groups". Can anyone please enlighten me if there is any step that I miss or have misunderstood? Thank you very much! (Or is there an easier way of enabling remote desktop that it can be used with a windows machine? I prefer not using VNC because I was hoping of being able to get better performance than that. And when I tried using XRDP I only received a black screen on the client.)

  Read the article

• How do I prevent missing network from slowing down boot-up?

  - by Ravi S Ghosh

  I have been having rather slow boot on Ubuntu 12.04. Lately, I tried to figure out the reason and it seems to be the network connection which does not get connected and requires multiple attempts. Here is part of dmesg [ 2.174349] EXT4-fs (sda2): INFO: recovery required on readonly filesystem [ 2.174352] EXT4-fs (sda2): write access will be enabled during recovery [ 2.308172] firewire_core: created device fw0: GUID 384fc00005198d58, S400 [ 2.333457] usb 7-1.2: new low-speed USB device number 3 using uhci_hcd [ 2.465896] EXT4-fs (sda2): recovery complete [ 2.466406] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null) [ 2.589440] usb 7-1.3: new low-speed USB device number 4 using uhci_hcd **[ 18.292029] ADDRCONF(NETDEV_UP): eth0: link is not ready** [ 18.458958] udevd[377]: starting version 175 [ 18.639482] Adding 4200960k swap on /dev/sda5. Priority:-1 extents:1 across:4200960k [ 19.314127] wmi: Mapper loaded [ 19.426602] r592 0000:09:01.2: PCI INT B -> GSI 18 (level, low) -> IRQ 18 [ 19.426739] r592: driver successfully loaded [ 19.460105] input: Dell WMI hotkeys as /devices/virtual/input/input5 [ 19.493629] lp: driver loaded but no devices found [ 19.497012] cfg80211: Calling CRDA to update world regulatory domain [ 19.535523] ACPI Warning: _BQC returned an invalid level (20110623/video-480) [ 19.539457] acpi device:03: registered as cooling_device2 [ 19.539520] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:01/LNXVIDEO:00/input/input6 [ 19.539568] ACPI: Video Device [M86] (multi-head: yes rom: no post: no) [ 19.578060] Linux video capture interface: v2.00 [ 19.667708] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2) [ 19.763171] r852 0000:09:01.3: PCI INT B -> GSI 18 (level, low) -> IRQ 18 [ 19.763258] r852: driver loaded successfully [ 19.854769] input: Microsoft Comfort Curve Keyboard 2000 as /devices/pci0000:00/0000:00:1d.1/usb7/7-1/7-1.2/7-1.2:1.0/input/input7 [ 19.854864] generic-usb 0003:045E:00DD.0001: input,hidraw0: USB HID v1.11 Keyboard [Microsoft Comfort Curve Keyboard 2000] on usb-0000:00:1d.1-1.2/input0 [ 19.878605] input: Microsoft Comfort Curve Keyboard 2000 as /devices/pci0000:00/0000:00:1d.1/usb7/7-1/7-1.2/7-1.2:1.1/input/input8 [ 19.878698] generic-usb 0003:045E:00DD.0002: input,hidraw1: USB HID v1.11 Device [Microsoft Comfort Curve Keyboard 2000] on usb-0000:00:1d.1-1.2/input1 [ 19.902779] input: DELL DELL USB Laser Mouse as /devices/pci0000:00/0000:00:1d.1/usb7/7-1/7-1.3/7-1.3:1.0/input/input9 [ 19.925034] generic-usb 0003:046D:C063.0003: input,hidraw2: USB HID v1.10 Mouse [DELL DELL USB Laser Mouse] on usb-0000:00:1d.1-1.3/input0 [ 19.925057] usbcore: registered new interface driver usbhid [ 19.925059] usbhid: USB HID core driver [ 19.942362] uvcvideo: Found UVC 1.00 device Laptop_Integrated_Webcam_2M (0c45:63ea) [ 19.947004] input: Laptop_Integrated_Webcam_2M as /devices/pci0000:00/0000:00:1a.7/usb1/1-6/1-6:1.0/input/input10 [ 19.947075] usbcore: registered new interface driver uvcvideo [ 19.947077] USB Video Class driver (1.1.1) [ 20.145232] Intel(R) Wireless WiFi Link AGN driver for Linux, in-tree: [ 20.145235] Copyright(c) 2003-2011 Intel Corporation [ 20.145327] iwlwifi 0000:04:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 20.145357] iwlwifi 0000:04:00.0: setting latency timer to 64 [ 20.145402] iwlwifi 0000:04:00.0: pci_resource_len = 0x00002000 [ 20.145404] iwlwifi 0000:04:00.0: pci_resource_base = ffffc90000674000 [ 20.145407] iwlwifi 0000:04:00.0: HW Revision ID = 0x0 [ 20.145531] iwlwifi 0000:04:00.0: irq 46 for MSI/MSI-X [ 20.145613] iwlwifi 0000:04:00.0: Detected Intel(R) WiFi Link 5100 AGN, REV=0x54 [ 20.145720] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 20.167535] iwlwifi 0000:04:00.0: device EEPROM VER=0x11f, CALIB=0x4 [ 20.167538] iwlwifi 0000:04:00.0: Device SKU: 0Xf0 [ 20.167567] iwlwifi 0000:04:00.0: Tunable channels: 13 802.11bg, 24 802.11a channels [ 20.172779] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel. [ 20.172783] Disabling lock debugging due to kernel taint [ 20.250115] [fglrx] Maximum main memory to use for locked dma buffers: 3759 MBytes. [ 20.250567] [fglrx] vendor: 1002 device: 9553 count: 1 [ 20.251256] [fglrx] ioport: bar 1, base 0x2000, size: 0x100 [ 20.251271] pci 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 20.251277] pci 0000:01:00.0: setting latency timer to 64 [ 20.251559] [fglrx] Kernel PAT support is enabled [ 20.251578] [fglrx] module loaded - fglrx 8.96.4 [Mar 12 2012] with 1 minors [ 20.310385] iwlwifi 0000:04:00.0: loaded firmware version 8.83.5.1 build 33692 [ 20.310598] Registered led device: phy0-led [ 20.310628] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain [ 20.372306] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs' [ 20.411015] psmouse serio1: synaptics: Touchpad model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd04733/0xa40000/0xa0000 [ 20.454232] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input11 [ 20.545636] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain [ 20.545640] cfg80211: World regulatory domain updated: [ 20.545642] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 20.545644] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 20.545647] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 20.545649] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 20.545652] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 20.545654] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 20.609484] type=1400 audit(1340502633.160:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=693 comm="apparmor_parser" [ 20.609494] type=1400 audit(1340502633.160:3): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=642 comm="apparmor_parser" [ 20.609843] type=1400 audit(1340502633.160:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=693 comm="apparmor_parser" [ 20.609852] type=1400 audit(1340502633.160:5): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=642 comm="apparmor_parser" [ 20.610047] type=1400 audit(1340502633.160:6): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=693 comm="apparmor_parser" [ 20.610060] type=1400 audit(1340502633.160:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=642 comm="apparmor_parser" [ 20.610476] type=1400 audit(1340502633.160:8): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=814 comm="apparmor_parser" [ 20.610829] type=1400 audit(1340502633.160:9): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=814 comm="apparmor_parser" [ 20.611035] type=1400 audit(1340502633.160:10): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=814 comm="apparmor_parser" [ 20.661912] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 [ 20.661982] snd_hda_intel 0000:00:1b.0: irq 47 for MSI/MSI-X [ 20.662013] snd_hda_intel 0000:00:1b.0: setting latency timer to 64 [ 20.770289] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12 [ 20.770689] snd_hda_intel 0000:01:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 20.770786] snd_hda_intel 0000:01:00.1: irq 48 for MSI/MSI-X [ 20.770815] snd_hda_intel 0000:01:00.1: setting latency timer to 64 [ 20.994040] HDMI status: Codec=0 Pin=3 Presence_Detect=0 ELD_Valid=0 [ 20.994189] input: HDA ATI HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input13 [ 21.554799] vesafb: mode is 1024x768x32, linelength=4096, pages=0 [ 21.554802] vesafb: scrolling: redraw [ 21.554804] vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0 [ 21.557342] vesafb: framebuffer at 0xd0000000, mapped to 0xffffc90011800000, using 3072k, total 3072k [ 21.557498] Console: switching to colour frame buffer device 128x48 [ 21.557516] fb0: VESA VGA frame buffer device [ 21.987338] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro [ 22.184693] EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: (null) [ 27.362440] iwlwifi 0000:04:00.0: RF_KILL bit toggled to disable radio. [ 27.436988] init: failsafe main process (986) killed by TERM signal [ 27.970112] ppdev: user-space parallel port driver [ 28.198917] Bluetooth: Core ver 2.16 [ 28.198935] NET: Registered protocol family 31 [ 28.198937] Bluetooth: HCI device and connection manager initialized [ 28.198940] Bluetooth: HCI socket layer initialized [ 28.198941] Bluetooth: L2CAP socket layer initialized [ 28.198947] Bluetooth: SCO socket layer initialized [ 28.226135] Bluetooth: RFCOMM TTY layer initialized [ 28.226141] Bluetooth: RFCOMM socket layer initialized [ 28.226143] Bluetooth: RFCOMM ver 1.11 [ 28.445620] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 28.445623] Bluetooth: BNEP filters: protocol multicast [ 28.524578] type=1400 audit(1340502641.076:11): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=1052 comm="apparmor_parser" [ 28.525018] type=1400 audit(1340502641.076:12): apparmor="STATUS" operation="profile_load" name="/usr/sbin/cupsd" pid=1052 comm="apparmor_parser" [ 28.629957] type=1400 audit(1340502641.180:13): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=1105 comm="apparmor_parser" [ 28.630325] type=1400 audit(1340502641.180:14): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=1105 comm="apparmor_parser" [ 28.630535] type=1400 audit(1340502641.180:15): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=1105 comm="apparmor_parser" [ 28.645266] type=1400 audit(1340502641.196:16): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper" pid=1104 comm="apparmor_parser" **[ 28.751922] ADDRCONF(NETDEV_UP): wlan0: link is not ready** [ 28.753653] tg3 0000:08:00.0: irq 49 for MSI/MSI-X **[ 28.856127] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 28.857034] ADDRCONF(NETDEV_UP): eth0: link is not ready** [ 28.871080] type=1400 audit(1340502641.420:17): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=1108 comm="apparmor_parser" [ 28.871519] type=1400 audit(1340502641.420:18): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/telepathy-*" pid=1108 comm="apparmor_parser" [ 28.874905] type=1400 audit(1340502641.424:19): apparmor="STATUS" operation="profile_replace" name="/usr/lib/cups/backend/cups-pdf" pid=1113 comm="apparmor_parser" [ 28.875354] type=1400 audit(1340502641.424:20): apparmor="STATUS" operation="profile_replace" name="/usr/sbin/cupsd" pid=1113 comm="apparmor_parser" [ 30.477976] tg3 0000:08:00.0: eth0: Link is up at 100 Mbps, full duplex [ 30.477979] tg3 0000:08:00.0: eth0: Flow control is on for TX and on for RX **[ 30.478390] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready** [ 31.110269] fglrx_pci 0000:01:00.0: irq 50 for MSI/MSI-X [ 31.110859] [fglrx] Firegl kernel thread PID: 1327 [ 31.111021] [fglrx] Firegl kernel thread PID: 1329 [ 31.111408] [fglrx] Firegl kernel thread PID: 1330 [ 31.111543] [fglrx] IRQ 50 Enabled [ 31.712938] [fglrx] Gart USWC size:1224 M. [ 31.712941] [fglrx] Gart cacheable size:486 M. [ 31.712945] [fglrx] Reserved FB block: Shared offset:0, size:1000000 [ 31.712948] [fglrx] Reserved FB block: Unshared offset:fc2b000, size:3d5000 [ 31.712950] [fglrx] Reserved FB block: Unshared offset:1fffb000, size:5000 [ 41.312020] eth0: no IPv6 routers present As you can see I get multiple instances of [ 28.856127] ADDRCONF(NETDEV_UP): eth0: link is not ready and then finally it becomes read and I get the message [ 30.478390] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready. I searched askubuntun, ubuntuforum, and the web but couldn't find a solution. Any help would be very much appreciated. Here is the bootchart

  Read the article

• Cron not able to succesfully change background

  - by Solenoid

  I'm running 12.04 with a custom XML background (modification on Day of Ubuntu) that changes based on time of day. I've noticed that there's a significant delay between when the changes are scheduled to take place in the XML file and when they actually show up on the background. I've also noticed that when I resume from suspend I don't get the correct background image either. I've found that cycling the wallpaper manually will fix this, and I've written a script to automate the process. If I execute the script manually it works fine. However, when I schedule the script to run in cron, cron doesn't change the background. To make sure that the script was being run properly by cron, I had it create a directory in my home folder after running the background change, and the directory is created successfully, so I know cron is running and executing the script. My script: #!/bin/bash sleep 5 gsettings set org.gnome.desktop.background picture-uri file:///home/zak/Pictures/Wallpaper/DOU2.xml sleep 1 gsettings set org.gnome.desktop.background picture-uri file:///home/zak/Pictures/Wallpaper/DOU.xml sleep 1 mkdir /home/zak/iscronworking exit Is cron just not able to access gsettings? The job is on my user crontab so it shouldn't be running as root. Alternately, is there any way to make Precise play nicely with XML wallpaper?

  Read the article

• Ubuntu 12.04 Boot Error

  - by Aman

  My Laptop was working just fine a day back but it started show the following error on booting: error: couldn't read file So, I googled about it and used a Live-CD to use Boot-Repair as told here: "can't read file" error after installation causes system to not boot I was given this link: http://paste.ubuntu.com/1441528/ if there are issues still. I also tried to do it again by a Boot-Repair-Disk this time and now I am getting the following error: error: couldn't read file error: you need to load the kernel first The boot-repair-disk gave me this link: http://paste2.org/p/2609703 if there are further issues.

  Read the article

• Ubutu 14.04 triple screen, third screen black and X cursor

  - by Horse

  I am having some issues getting my third screen working properly. I had triple screens working fine on 12.04, using 2 nvidia cards. Did a fresh install of 14.04 and having no end of problems getting it working. It either will just be disabled, or the screen is black with the cursor as an X. I can only enable it from the nvidia server settings tool. The Ubuntu native display settings won't even show the 3rd screen. I tried copying the xorg.conf from my old install, which upon restarting X worked fine on the login screen, but then it just sat there after I logged in and didn’t do anything (mouse was still working). I am using gnome-session-fallback instead of unity if that makes any difference. Still having these issues if I try unity though. How do I get my 3rd screen working and displaying a desktop? Here is my current xorg.conf # nvidia-settings: X configuration file generated by nvidia-settings # nvidia-settings: version 331.20 (buildd@roseapple) Mon Feb 3 15:07:22 UTC 2014 Section "ServerLayout" Identifier "Layout0" Screen 0 "Screen0" 0 0 Screen 1 "Screen1" RightOf "Screen0" InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" Option "Xinerama" "0" EndSection Section "Files" EndSection Section "InputDevice" # generated from default Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/psaux" Option "Emulate3Buttons" "no" Option "ZAxisMapping" "4 5" EndSection Section "InputDevice" # generated from default Identifier "Keyboard0" Driver "kbd" EndSection Section "Monitor" # HorizSync source: edid, VertRefresh source: edid Identifier "Monitor0" VendorName "Unknown" ModelName "DELL 1907FP" HorizSync 30.0 - 81.0 VertRefresh 56.0 - 76.0 Option "DPMS" EndSection Section "Monitor" # HorizSync source: unknown, VertRefresh source: unknown Identifier "Monitor1" VendorName "Unknown" ModelName "DELL 1907FP" HorizSync 0.0 - 0.0 VertRefresh 0.0 Option "DPMS" EndSection Section "Monitor" Identifier "Monitor2" VendorName "Unknown" ModelName "DELL 1907FP" HorizSync 30.0 - 81.0 VertRefresh 56.0 - 76.0 EndSection Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "GeForce GTX 580" BusID "PCI:1:0:0" EndSection Section "Device" Identifier "Device1" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "GeForce GT 520" BusID "PCI:3:0:0" EndSection Section "Device" Identifier "Device2" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "GeForce GT 520" BusID "PCI:3:0:0" EndSection Section "Screen" # Removed Option "metamodes" "DVI-I-2: nvidia-auto-select +0+0, DVI-I-3: nvidia-auto-select +1280+0" # Removed Option "metamodes" "DVI-I-2: nvidia-auto-select +0+0" # Removed Option "SLI" "Off" # Removed Option "BaseMosaic" "off" # Removed Option "metamodes" "GPU-109d4eb8-b40b-87d7-3fd6-95830d1d5215.DVI-I-2: nvidia-auto-select +0+0, GPU-109d4eb8-b40b-87d7-3fd6-95830d1d5215.DVI-I-3: nvidia-auto-select +1280+0, GPU-82e96214-175e-5e6a-218c-5bdbc948daf2.DVI-I-1: nvidia-auto-select +3200+0" # Removed Option "SLI" "off" # Removed Option "BaseMosaic" "on" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 Option "Stereo" "0" Option "nvidiaXineramaInfoOrder" "DFP-0" Option "metamodes" "DVI-I-2: nvidia-auto-select +0+0, DVI-I-3: nvidia-auto-select +1280+0" Option "SLI" "Off" Option "MultiGPU" "Off" Option "BaseMosaic" "off" SubSection "Display" Depth 24 EndSubSection EndSection Section "Screen" # Removed Option "metamodes" "nvidia-auto-select +0+0" # Removed Option "metamodes" "DVI-I-3: nvidia-auto-select +0+0" Identifier "Screen1" Device "Device1" Monitor "Monitor1" DefaultDepth 24 Option "Stereo" "0" Option "metamodes" "nvidia-auto-select +0+0" Option "SLI" "Off" Option "MultiGPU" "Off" Option "BaseMosaic" "off" SubSection "Display" Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen2" Device "Device2" Monitor "Monitor2" DefaultDepth 24 Option "Stereo" "0" Option "metamodes" "nvidia-auto-select +0+0" Option "SLI" "Off" Option "MultiGPU" "Off" Option "BaseMosaic" "off" SubSection "Display" Depth 24 EndSubSection EndSection Here is my old 'working in 12.04' xorg.conf # nvidia-settings: X configuration file generated by nvidia-settings # nvidia-settings: version 310.19 ([email protected]) Thu Nov 8 02:08:55 PST 2012 Section "ServerLayout" # Removed Option "Xinerama" "0" Identifier "Layout0" Screen 0 "Screen0" 0 0 Screen 1 "Screen1" RightOf "Screen2" Screen 2 "Screen2" RightOf "Screen0" InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" Option "Xinerama" "1" EndSection Section "Files" EndSection Section "InputDevice" # generated from default Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/psaux" Option "Emulate3Buttons" "no" Option "ZAxisMapping" "4 5" EndSection Section "InputDevice" # generated from default Identifier "Keyboard0" Driver "kbd" EndSection Section "Monitor" # HorizSync source: edid, VertRefresh source: edid Identifier "Monitor0" VendorName "Unknown" ModelName "DELL 1907FP" HorizSync 30.0 - 81.0 VertRefresh 56.0 - 76.0 Option "DPMS" EndSection Section "Monitor" # HorizSync source: unknown, VertRefresh source: unknown Identifier "Monitor1" VendorName "Unknown" ModelName "DELL 1907FP" HorizSync 30.0 - 81.0 VertRefresh 56.0 - 76.0 Option "DPMS" EndSection Section "Monitor" Identifier "Monitor2" VendorName "Unknown" ModelName "Apple Cinema HD" HorizSync 74.0 - 74.6 VertRefresh 59.9 - 60.0 EndSection Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "GeForce GTX 580" BusID "PCI:1:0:0" Screen 0 EndSection Section "Device" Identifier "Device1" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "GeForce GT 520" BusID "PCI:3:0:0" EndSection Section "Device" Identifier "Device2" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "GeForce GTX 580" BusID "PCI:1:0:0" Screen 1 EndSection Section "Screen" # Removed Option "metamodes" "DFP-0: nvidia-auto-select +0+0, DFP-2: nvidia-auto-select +1280+0" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 Option "Stereo" "0" Option "metamodes" "DFP-0: nvidia-auto-select +0+0; DFP-0: nvidia-auto-select +0+0; DFP-0: 1280x1024_75 +0+0; DFP-0: 1152x864 +0+0; DFP-0: 1024x768 +0+0; DFP-0: 1024x768_60 +0+0; DFP-0: 800x600 +0+0; DFP-0: 800x600_60 +0+0; DFP-0: 640x480 +0+0; DFP-0: 640x480_60 +0+0; DFP-0: nvidia-auto-select +0+0 {viewportout=1280x720+0+152}" SubSection "Display" Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen1" Device "Device1" Monitor "Monitor1" DefaultDepth 24 Option "Stereo" "0" Option "metamodes" "nvidia-auto-select +0+0" SubSection "Display" Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen2" Device "Device2" Monitor "Monitor2" DefaultDepth 24 Option "Stereo" "0" Option "metamodes" "DFP-2: nvidia-auto-select +0+0" SubSection "Display" Depth 24 EndSubSection EndSection Section "Extensions" Option "Composite" "Disable" EndSection

  Read the article

• Problem with installing Flash

  - by Hannah

  This question has been posted loads of times, I know, but seriously I've spent hours and HOURS searching the web for answers. Anyways, basically I have just installed Ubuntu 13.04 for the first time. I tried to get on youtube and found out I cannot play videos. When I went to install flash the windows popped up saying either install Adobe flash or gnash. installed Flash from the Adobe website. Three different files types to choose from. YUM, .tar.gz or .rpm. Now from what I could gather .tar.gz is the right one so I tried it and it downloaded without the error message. It comes up with the box that says open with archive manager. Extracted the files but none of them were of any use. Could not work out how to install it. There was no file intended for installation. So what am I meant to do with these files? Would it be easier to just install Gnash?

  Read the article

• Missing Wireless access point

  - by nvcnvn

  I have an: Ubuntu 12.04 with proprietary Boardcom STA Wireless driver installed BCM43224 802.11a/b/g/n wireless card TP-LINK TD-W8101G 54Mbps Wireless ADSL2+ Modem Router Yesterday before I went to sleep, I still connect to my wireless access point, this morning when I start my laptop I don't see it in the list - there are some neighbors listed but not mine. The WLAN is green, with my old Nokia E72, I still see my access point with 100% signal. I have tried to restart my laptop and turn the firmware off/on by the switch but no help. I have read the WirelessTroubleShootingGuide but I can do anything. Here is some of my card info: *-network description: Wireless interface product: BCM43224 802.11a/b/g/n vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: eth1 version: 01 serial: c0:cb:38:06:5d:53 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11abgn resources: irq:17 memory:f0500000-f0503fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:09:00.0 logical name: eth0 version: 03 serial: f0:4d:a2:42:ab:e4 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168d-1.fw ip=192.168.1.3 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:42 ioport:5000(size=256) memory:f0404000-f0404fff memory:f0400000-f0403fff memory:f0420000-f043ffff

  Read the article

• Cycles through black screen on login after changing password

  - by John L

  On my laptop, I forgot the password to my Ubuntu partition, so I logged into the root command shell on the recovery start up option in GRUB so that I could change the password. On my first attempt to change my user password, I got this error: root@username-PC:~# passwd username (*not my actual user name*) Enter new UNIX password: Retype new UNIX password: passwd: Authentication token manipulation error passwd: password unchanged After doing some research, I discovered that I was stuck as read only on the file system, so I ran the following command to remount the file partition as read/write: mount -rw -o remount / Afterwards, I change my user password using passwd and it was changed successfully. I restarted my laptop and tried to login using the new password but the only thing that happened was after entering my password it flashed to a black screen with some text that I couldn't make out except for "Ubuntu 12.04" then another black screen half a second later, and finally back to the login screen. Repeated attempts to login results in only this action.

  Read the article

• "bad mirror archive" : What should I put as the "mirror of ubuntu archive" on installation of ubuntu?

  - by rockit

  I'm trying to set up ubuntu from my old macintosh laptop, but when it asks me to put in the "mirror of ubuntu archive" I run into problems. For the mirror, I put in mirror.anl.gov for the ubuntu archive mirror directory, i put in pub/ubuntu/ Then I leave the http proxy blank and hit "continue" It then tries to "download release files", which starts at 0%, and eventually jumps straight to 100% and then it presents me with an error of "bad mirror archive". Any advice? I never set up ubuntu before, and I'm really struggling with this step.

  Read the article

• Ubuntu 11.10 doesn't detect Intel integrated graphics (i7-2670QM CPU)

  - by Telmo Marques

  The laptop I'm using is an MSI GT683DX-847PT that comes with an NVIDIA GeForce GTX570M discrete GPU, and an Intel Core i7-2670QM CPU. According to Intel's description of the Core i7-2670QM CPU, it has an HD Graphics 3000 integrated GPU. The problem is that the Intel integrated graphics GPU doesn't come up in lspci nor in lshw, only the NVIDIA GPU shows up. Here is the output of both commands: sudo lspci: http://pastebin.com/raw.php?i=9AZg8bJy sudo lshw: http://pastebin.com/raw.php?i=6cAMFQsY I was counting on having two GPU's to run CUDA programs on the discrete NVIDIA GPU, while X was handled by the integrated Intel GPU, to prevent kernel execution timeout. Why doesn't the Intel HD Graphics 3000 GPU show up? Any tests I could make to verify the presence of an integrated GPU?

  Read the article

• Hardware settings reviewing

  - by dino99

  Get some hardware related errors logged into dmesg: oem@dub:~$ dmesg | grep ata10 [ 1.007989] ata10: PATA max UDMA/133 cmd 0xa800 ctl 0xa480 bmdma 0xa408 irq 18 [ 1.691664] ata10: prereset failed (errno=-19) [ 1.691670] ata10: reset failed, giving up oem@dub:~$ dmesg | grep ata2 [ 0.990290] ata2: SATA max UDMA/133 abar m1024@0xfebfb800 port 0xfebfb980 irq 45 [ 1.688011] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 1.688055] ata2.00: unsupported device, disabling [ 1.688057] ata2.00: disabled As I understand, its related to my old Seagate SATA HDD, and the PATA CDROM. These errors are quite new, so I feel that their settings (dma, write-cache, ...) have been modified by some upgrades. I've already used hdparm to set write-cache off on the HDDs. But it seems like I need to review some other setting(s) too. With oldest distro it was easy to know about the hardware settings, but now on Quantal/Precise its deeply hidden for the average user. So i would like to know how to view/modify these settings. About the CDROM reader, the problem is different: - the system don't identify it with an UUID; but only with ATAPI or by-id oem@dub:~$ dmesg|grep 'ATAPI' [ 1.308611] ata3.00: ATAPI: TSSTcorp CDDVDW SH-S203D, SB00, max UDMA/100 oem@dub:~$ ls -l /dev/disk/by-id/ ...... lrwxrwxrwx 1 root root 9 oct. 1 06:42 ata-TSSTcorp_CDDVDW_SH-S203D -> ../../sr0 .....

  Read the article

• 5.1 surround sound on Acer Aspire 5738ZG with Ubuntu 11.10

  - by kbargais_LV

  I got a problem with sound. I tried everything but no results. :( I got 3 sound ports. my daemon: # This file is part of PulseAudio. # # PulseAudio is free software; you can redistribute it and/or modify # it under the terms of the GNU Lesser General Public License as published by # the Free Software Foundation; either version 2 of the License, or # (at your option) any later version. # # PulseAudio is distributed in the hope that it will be useful, but # WITHOUT ANY WARRANTY; without even the implied warranty of # MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU # General Public License for more details. # # You should have received a copy of the GNU Lesser General Public License # along with PulseAudio; if not, write to the Free Software # Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 # USA. ## Configuration file for the PulseAudio daemon. See pulse-daemon.conf(5) for ## more information. Default values are commented out. Use either ; or # for ## commenting. ; daemonize = no ; fail = yes ; allow-module-loading = yes ; allow-exit = yes ; use-pid-file = yes ; system-instance = no ; local-server-type = user ; enable-shm = yes ; shm-size-bytes = 0 # setting this 0 will use the system-default, usually 64 MiB ; lock-memory = no ; cpu-limit = no ; high-priority = yes ; nice-level = -11 ; realtime-scheduling = yes ; realtime-priority = 5 ; exit-idle-time = 20 ; scache-idle-time = 20 ; dl-search-path = (depends on architecture) ; load-default-script-file = yes ; default-script-file = /etc/pulse/default.pa ; log-target = auto ; log-level = notice ; log-meta = no ; log-time = no ; log-backtrace = 0 resample-method = speex-float-1 ; enable-remixing = yes ; enable-lfe-remixing = no flat-volumes = no ; rlimit-fsize = -1 ; rlimit-data = -1 ; rlimit-stack = -1 ; rlimit-core = -1 ; rlimit-as = -1 ; rlimit-rss = -1 ; rlimit-nproc = -1 ; rlimit-nofile = 256 ; rlimit-memlock = -1 ; rlimit-locks = -1 ; rlimit-sigpending = -1 ; rlimit-msgqueue = -1 ; rlimit-nice = 31 ; rlimit-rtprio = 9 ; rlimit-rttime = 1000000 ; default-sample-format = s16le ; default-sample-rate = 44100 ; default-sample-channels = 6 ; default-channel-map = front-left,front-right default-fragments = 8 default-fragment-size-msec = 10 ; enable-deferred-volume = yes ; deferred-volume-safety-margin-usec = 8000 ; deferred-volume-extra-delay-usec = 0

  Read the article

• Acer Wireless Network not working

  - by pico

  I installed Ubuntu 12.04 64 Bit desktop version in acer AspireE1-470. Everything work great except Wireless and touch pad. When i run additional driver there nothing to activate and when i run "rfkill list" it's show 0: hci0:bluetooth Soft blocked: yes Hard Blocked: no 1: acer-wireless: Wireless Lan Soft blocked: no Hard blocked: no I don't know too much command in linux and i hv no i ieda hot to work wireless and touch-pad

  Read the article

• Mounting Samsung Galaxy S2 via USB on Ubuntu 13.04

  - by argvar

  Connecting my Samsung Galaxy S2 to Windows 7 worked seamlessly. Now that I'm on Ubuntu 13.04 I'd like to access my phone's drive via the USB cable, but that's not working. When I do plug it in I get a error message in Ubuntu: Unable to mount SAMSUNG_Android Unable to open MTP device '[usb:002,008]' Then when I unplug it I see a error message on the phone: Attention Unable to find software on your PC that can recognize your device. Service pack 3, Windows Media Player, version 10 or higher, for Windows XP or Android FIle Transfer for Mac OS must be installed. You can download and install PC Kies from http://www.samsung.com/kies in order to sync data with your device, back up data, and upgrade your device (Windows and Mac OS are supported) What can I do here to fix this? I don't want to use any special software with the phone, just access the phone's drive.

  Read the article

• Are libc versions tied to kernel versions?

  - by mathematician1975

  After reading the answers to my previous question I have come to the conclusion that an answer to the following question is what I was actually looking for: Does a particular version of the kernel require a particular version of libc to run properly? Basically my problem stems from building an application on my 12.04 ubuntu and trying to run it on 8.04. I have since learned from this and other stackexchange forums that it is backward compatibility of libc that causes these problems. Therefore what I am perhaps naively trying to do is build the same version of libc that exists on my target and then link against that on my host when I build the application. Then in an ideal world when I copy this to the host, having been linked to the "correct" libc it should work (in my head at least). I have been totally unable to find a way to install an older libc on my system, and wondered if each version is tightly bound to a kernel version, hence the above question.

  Read the article

• Cannot delete .Trash-503 directory, returns a $RECYCLE.BIN.trashinfo: Input/output error

  - by Parto

  I cannot delete .Trash-503 folder via GUI or terminal, it returns a $RECYCLE.BIN.trashinfo: Input/output error Not even sudo rm -r or even a simple ls works in that trash directory. Check terminal output below: subroot@subroot:~$ cd /media/xxxxx/ subroot@subroot:/media/xxxxx$ rm .Trash-503/ rm: cannot remove `.Trash-503/': Is a directory subroot@subroot:/media/xxxxx$ rm -r .Trash-503/ rm: cannot remove `.Trash-503/info/$RECYCLE.BIN.trashinfo': Input/output error rm: cannot remove `.Trash-503/info/found.000.trashinfo': Input/output error rm: cannot remove `.Trash-503/info': Directory not empty subroot@subroot:/media/xxxxx$ sudo rm -r .Trash-503/ [sudo] password for subroot: rm: cannot remove `.Trash-503/info/$RECYCLE.BIN.trashinfo': Input/output error rm: cannot remove `.Trash-503/info/found.000.trashinfo': Input/output error subroot@subroot:/media/xxxxx$ cd .Trash-503/ subroot@subroot:/media/xxxxx/.Trash-503$ ls info subroot@subroot:/media/xxxxx/.Trash-503$ cd info/ subroot@subroot:/media/xxxxx/.Trash-503/info$ ls ls: cannot access $RECYCLE.BIN.trashinfo: Input/output error ls: cannot access found.000.trashinfo: Input/output error found.000.trashinfo $RECYCLE.BIN.trashinfo subroot@subroot:/media/xxxxx/.Trash-503/info$ What's going on here and how can I delete this folder? EDIT I tried checking and repairing the partition using gparted only to get this error message: ERROR: Filesystem check failed! ERROR: 264 clusters are referenced multiple times. NTFS is inconsistent. Run chkdsk /f on Windows then reboot it TWICE! The usage of the /f parameter is very IMPORTANT! No modification was and will be made to NTFS by this software until it gets repaired. I don't have windows installed, how can I run chkdsk /f from ubuntu?

  Read the article

• How to change tooltip background color in Unity?

  - by kayahr

  In a lot of applications the tooltips are just plain ugly (White text on black background, way too much contrast) or even unreadable (black or dark blue text (Hyperlinks) on black background). I want to change the background color of the tooltips to some medium gray or even some yellow or something like that, maybe even something semi-transparent. Here is a screenshot of Eclipse which displays some source code in a tool tip with black text on black background: Switching to a different theme (Something other than Ambiance or Radiance) helps but I like Ambiance and I want to keep it. It's just this darn tooltip color which is absolutely unacceptable. I found several solutions for older Ubuntu versions but they no longer work with Unity in Ubuntu 11.10 because I can't find any function to customize the Ambiance or Radiance theme. So how do I do that in the current Ubuntu version?

  Read the article

< Previous Page | 236 237 238 239 240 241 242 243 244 245 246 247  | Next Page >