Search Results

Search found 6605 results on 265 pages for 'complex networks'.

Page 241/265 | < Previous Page | 237 238 239 240 241 242 243 244 245 246 247 248  | Next Page >

• Cisco PIX 8.0.4, static address mapping not working?

  - by Bill

  upgrading a working Pix running 5.3.1 to 8.0.4. The memory/IOS upgrade went fine, but the 8.0.4 configuration is not quite working 100%. The 5.3.1 config on which it was based is working fine. Basically, I have three networks (inside, outside, dmz) with some addresses on the dmz statically mapped to outside addresses. The problem seems to be that those addresses can't send or receive traffic from the outside (Internet.) Stuff on the DMZ that does not have a static mapping seems to work fine. So, basically: Inside - outside: works Inside - DMZ: works DMZ - inside: works, where the rules allow it DMZ (non-static) - outside: works But: DMZ (static) - outside: fails Outside - DMZ: fails (So, say, udp 1194 traffic to .102, http to .104) I suspect there's something I'm missing with the nat/global section of the config, but can't for the life of me figure out what. Help, anyone? The complete configuration is below. Thanks for any thoughts! ! PIX Version 8.0(4) ! hostname firewall domain-name asasdkpaskdspakdpoak.com enable password xxxxxxxx encrypted passwd xxxxxxxx encrypted names ! interface Ethernet0 nameif outside security-level 0 ip address XX.XX.XX.100 255.255.255.224 ! interface Ethernet1 nameif inside security-level 100 ip address 192.168.68.1 255.255.255.0 ! interface Ethernet2 nameif dmz security-level 10 ip address 192.168.69.1 255.255.255.0 ! boot system flash:/image.bin ftp mode passive dns server-group DefaultDNS domain-name asasdkpaskdspakdpoak.com access-list acl_out extended permit udp any host XX.XX.XX.102 eq 1194 access-list acl_out extended permit tcp any host XX.XX.XX.104 eq www access-list acl_dmz extended permit tcp host 192.168.69.10 host 192.168.68.17 eq ssh access-list acl_dmz extended permit tcp 10.71.83.0 255.255.255.0 192.168.68.0 255.255.255.0 eq ssh access-list acl_dmz extended permit tcp 10.71.83.0 255.255.255.0 192.168.68.0 255.255.255.0 eq 5901 access-list acl_dmz extended permit udp host 192.168.69.103 any eq ntp access-list acl_dmz extended permit udp host 192.168.69.103 any eq domain access-list acl_dmz extended permit tcp host 192.168.69.103 any eq www access-list acl_dmz extended permit tcp host 192.168.69.100 host 192.168.68.101 eq 3306 access-list acl_dmz extended permit tcp host 192.168.69.100 host 192.168.68.102 eq 3306 access-list acl_dmz extended permit tcp host 192.168.69.101 host 192.168.68.101 eq 3306 access-list acl_dmz extended permit tcp host 192.168.69.101 host 192.168.68.102 eq 3306 access-list acl_dmz extended permit tcp 10.71.83.0 255.255.255.0 host 192.168.68.101 eq 3306 access-list acl_dmz extended permit tcp 10.71.83.0 255.255.255.0 host 192.168.68.102 eq 3306 access-list acl_dmz extended permit tcp host 192.168.69.104 host 192.168.68.101 eq 3306 access-list acl_dmz extended permit tcp host 192.168.69.104 host 192.168.68.102 eq 3306 access-list acl_dmz extended permit tcp 10.71.83.0 255.255.255.0 host 192.168.69.104 eq 8080 access-list acl_dmz extended permit tcp 10.71.83.0 255.255.255.0 host 192.168.69.104 eq 8099 access-list acl_dmz extended permit tcp host 192.168.69.105 any eq www access-list acl_dmz extended permit tcp host 192.168.69.103 any eq smtp access-list acl_dmz extended permit tcp host 192.168.69.105 host 192.168.68.103 eq ssh access-list acl_dmz extended permit tcp host 192.168.69.104 any eq www access-list acl_dmz extended permit tcp host 192.168.69.100 any eq www access-list acl_dmz extended permit tcp host 192.168.69.100 any eq https pager lines 24 mtu outside 1500 mtu inside 1500 mtu dmz 1500 icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 1 0.0.0.0 0.0.0.0 nat (dmz) 1 0.0.0.0 0.0.0.0 static (dmz,outside) XX.XX.XX.103 192.168.69.11 netmask 255.255.255.255 static (inside,dmz) 192.168.68.17 192.168.68.17 netmask 255.255.255.255 static (inside,dmz) 192.168.68.100 192.168.68.100 netmask 255.255.255.255 static (inside,dmz) 192.168.68.101 192.168.68.101 netmask 255.255.255.255 static (inside,dmz) 192.168.68.102 192.168.68.102 netmask 255.255.255.255 static (inside,dmz) 192.168.68.103 192.168.68.103 netmask 255.255.255.255 static (dmz,outside) XX.XX.XX.104 192.168.69.100 netmask 255.255.255.255 static (dmz,outside) XX.XX.XX.105 192.168.69.105 netmask 255.255.255.255 static (dmz,outside) XX.XX.XX.102 192.168.69.10 netmask 255.255.255.255 access-group acl_out in interface outside access-group acl_dmz in interface dmz route outside 0.0.0.0 0.0.0.0 XX.XX.XX.97 1 route dmz 10.71.83.0 255.255.255.0 192.168.69.10 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute dynamic-access-policy-record DfltAccessPolicy no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 telnet 192.168.68.17 255.255.255.255 inside telnet timeout 5 ssh timeout 5 console timeout 0 threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect netbios inspect rsh inspect rtsp inspect skinny inspect esmtp inspect sqlnet inspect sunrpc inspect tftp inspect sip inspect xdmcp ! service-policy global_policy global prompt hostname context Cryptochecksum:2d1bb2dee2d7a3e45db63a489102d7de

  Read the article

• Why does my macbook pro have long ping times over wifi?

  - by randynov

  I have been having problems connecting with my wifi. It is weird, the ping times to the router (<30 feet away) seem to surge, often getting over 10s before slowly coming back down. You can see the trend below. I'm on a macbook pro and have done the normal stuff (reset the pram and smc, changed wireless channels, etc.). It happens across different routers, so I think it must be my laptop, but I don't know what it could be. The RSSI value hovers around -57, but I've seen the transmit rate flip between 0, 48 & 54. The signal strength is ~60% with 9% noise. Currently, there are 17 other wireless networks in range, but only one in the same channel. 1 - How can I figure out what's going on? 2 - How can I correct the situation? TIA! Randall PING 192.168.1.1 (192.168.1.1): 56 data bytes 64 bytes from 192.168.1.1: icmp_seq=0 ttl=254 time=781.107 ms 64 bytes from 192.168.1.1: icmp_seq=1 ttl=254 time=681.551 ms 64 bytes from 192.168.1.1: icmp_seq=2 ttl=254 time=610.001 ms 64 bytes from 192.168.1.1: icmp_seq=3 ttl=254 time=544.915 ms 64 bytes from 192.168.1.1: icmp_seq=4 ttl=254 time=547.622 ms 64 bytes from 192.168.1.1: icmp_seq=5 ttl=254 time=468.914 ms 64 bytes from 192.168.1.1: icmp_seq=6 ttl=254 time=237.368 ms 64 bytes from 192.168.1.1: icmp_seq=7 ttl=254 time=229.902 ms 64 bytes from 192.168.1.1: icmp_seq=8 ttl=254 time=11754.151 ms 64 bytes from 192.168.1.1: icmp_seq=9 ttl=254 time=10753.943 ms 64 bytes from 192.168.1.1: icmp_seq=10 ttl=254 time=9754.428 ms 64 bytes from 192.168.1.1: icmp_seq=11 ttl=254 time=8754.199 ms 64 bytes from 192.168.1.1: icmp_seq=12 ttl=254 time=7754.138 ms 64 bytes from 192.168.1.1: icmp_seq=13 ttl=254 time=6754.159 ms 64 bytes from 192.168.1.1: icmp_seq=14 ttl=254 time=5753.991 ms 64 bytes from 192.168.1.1: icmp_seq=15 ttl=254 time=4754.068 ms 64 bytes from 192.168.1.1: icmp_seq=16 ttl=254 time=3753.930 ms 64 bytes from 192.168.1.1: icmp_seq=17 ttl=254 time=2753.768 ms 64 bytes from 192.168.1.1: icmp_seq=18 ttl=254 time=1753.866 ms 64 bytes from 192.168.1.1: icmp_seq=19 ttl=254 time=753.592 ms 64 bytes from 192.168.1.1: icmp_seq=20 ttl=254 time=517.315 ms 64 bytes from 192.168.1.1: icmp_seq=37 ttl=254 time=1.315 ms 64 bytes from 192.168.1.1: icmp_seq=38 ttl=254 time=1.035 ms 64 bytes from 192.168.1.1: icmp_seq=39 ttl=254 time=4.597 ms 64 bytes from 192.168.1.1: icmp_seq=21 ttl=254 time=18010.681 ms 64 bytes from 192.168.1.1: icmp_seq=22 ttl=254 time=17010.449 ms 64 bytes from 192.168.1.1: icmp_seq=23 ttl=254 time=16010.430 ms 64 bytes from 192.168.1.1: icmp_seq=24 ttl=254 time=15010.540 ms 64 bytes from 192.168.1.1: icmp_seq=25 ttl=254 time=14010.450 ms 64 bytes from 192.168.1.1: icmp_seq=26 ttl=254 time=13010.175 ms 64 bytes from 192.168.1.1: icmp_seq=27 ttl=254 time=12010.282 ms 64 bytes from 192.168.1.1: icmp_seq=28 ttl=254 time=11010.265 ms 64 bytes from 192.168.1.1: icmp_seq=29 ttl=254 time=10010.285 ms 64 bytes from 192.168.1.1: icmp_seq=30 ttl=254 time=9010.235 ms 64 bytes from 192.168.1.1: icmp_seq=31 ttl=254 time=8010.399 ms 64 bytes from 192.168.1.1: icmp_seq=32 ttl=254 time=7010.144 ms 64 bytes from 192.168.1.1: icmp_seq=33 ttl=254 time=6010.113 ms 64 bytes from 192.168.1.1: icmp_seq=34 ttl=254 time=5010.025 ms 64 bytes from 192.168.1.1: icmp_seq=35 ttl=254 time=4009.966 ms 64 bytes from 192.168.1.1: icmp_seq=36 ttl=254 time=3009.825 ms 64 bytes from 192.168.1.1: icmp_seq=40 ttl=254 time=16000.676 ms 64 bytes from 192.168.1.1: icmp_seq=41 ttl=254 time=15000.477 ms 64 bytes from 192.168.1.1: icmp_seq=42 ttl=254 time=14000.388 ms 64 bytes from 192.168.1.1: icmp_seq=43 ttl=254 time=13000.549 ms 64 bytes from 192.168.1.1: icmp_seq=44 ttl=254 time=12000.469 ms 64 bytes from 192.168.1.1: icmp_seq=45 ttl=254 time=11000.332 ms 64 bytes from 192.168.1.1: icmp_seq=46 ttl=254 time=10000.339 ms 64 bytes from 192.168.1.1: icmp_seq=47 ttl=254 time=9000.338 ms 64 bytes from 192.168.1.1: icmp_seq=48 ttl=254 time=8000.198 ms 64 bytes from 192.168.1.1: icmp_seq=49 ttl=254 time=7000.388 ms 64 bytes from 192.168.1.1: icmp_seq=50 ttl=254 time=6000.217 ms 64 bytes from 192.168.1.1: icmp_seq=51 ttl=254 time=5000.084 ms 64 bytes from 192.168.1.1: icmp_seq=52 ttl=254 time=3999.920 ms 64 bytes from 192.168.1.1: icmp_seq=53 ttl=254 time=3000.010 ms 64 bytes from 192.168.1.1: icmp_seq=54 ttl=254 time=1999.832 ms 64 bytes from 192.168.1.1: icmp_seq=55 ttl=254 time=1000.072 ms 64 bytes from 192.168.1.1: icmp_seq=58 ttl=254 time=1.125 ms 64 bytes from 192.168.1.1: icmp_seq=59 ttl=254 time=1.070 ms 64 bytes from 192.168.1.1: icmp_seq=60 ttl=254 time=2.515 ms

  Read the article

• Poor home office network performance and cannot figure out where the issue is

  - by Jeff Willener

  This is the most bizarre issue. I have worked with small to mid size networks for quite a long time and can say I'm comfortable connecting hardware. Where you will start to lose me is with managed switches and firewalls. To start, let me describe my network (sigh, shouldn't but I MUST solve this). 1) Comcast Cable Internet 2) Motorola SURFboard eXtreme Cable Modem. a) Model: SB6120 b) DOCSIS 3.0 and 2.0 support c) IPv4 and IPv6 support 3-A) Cisco Small Business RV220W Wireless N Firewall a) Latest firmware b) Model: RV220W-A-K9-NA c) WAN Port to Modem (2) d) vlan 1: work e) vlan 2: everything else. 3-B) D-Link DIR-615 Draft 802.11 N Wireless Router a) Latest firmware b) WAN Port to Modem (2) 4) Servers connected directly to firewall a) If firewall 3-A, then vlan 1 b) CAT5e patch cables c) Dell PowerEdge 1400SC w/ 10/100 integrated NIC (Domain Controller, DNS, former DHCP) d) Dell PowerEdge 400SC w/ 10/100/1000 integrated NIC (VMWare Server) 4) Linksys EZXS88W unmanaged Workgroup 10/100 Switch a) If firewall 3-A, then vlan 2 b) 25' CAT5e patch cable to firewall (3-A or 3-B) c) Connects xBox 360, Blu-Ray player, PC at TV 5) Office equipment connected directly to firewall a) If firewall 3-A, then vlan 1 b) ~80' CAT6 or CAT5e patch cable to firewall (3-A or 3-B) c) Connects 1) Dell Latitude laptop 10/100/1000 2) Dell Inspiron laptop 10/100 3) Dell Workstation 10/100/1000 (Pristine host, VMWare Workstation 7.x with many bridged VM's) 4) Brother Laser Printer 10/100 5) Epson All-In-One Workforce 310 10/100 5-A) NetGear FS116 unmanaged 10/100 switch a) I've had this switch for a long time and never had issues. 5-B) NetGear GS108 unmanaged 10/100/1000 switch a) Bought new for this issue and returned. 5-C) Linksys SE2500 unmanaged 10/100/1000 switch a) Bought new for this issue and returned. 5-D) TP-Link TL-SG10008D unmanaged 10/100/1000 a) Bought new for this issue and still have. 6) VLan 1 Wireless Connections (on same subnet if 3-B) a) Any of those at 5c b) HP Laptop 7) VLan 2 Wireless Connection (on same subnet if 3-B) a) IPad, IPod b) Compaq Laptop c) Epson Wireless Printer Shew, without hosting a diagram I hope that paints a good picture. The Issue The breakdown here is at item 5. No matter what I do I cannot have a switch at 5 and have to run everything wireless regardless of router. Issues related to using a switch (point 5 above) SpeedTest is good. Poor throughput to other devices if can communicate at all. Usually cannot ping other devices even on the same switch although, when able, ping times are good. Eventual lose of connectivity and can "sometimes" be restored by unplugging everything for several days, not minutes or hours but we're talking a week if at all. Directly connect to computer gives good internet connection however throughput to other devices connected to firewall is at best horrible. Yet printing doesn't seem to be an issue as long as they are connected via wireless. I have to force the RV220W to 1000Mb on the respective port if using a Gig Switch Issues related to using wireless in place of a switch (point 5 above) Poor throughput to other devices if can communicate. SpeedTest is good. Bottom line Internet speeds are awesome. By the way, Comcast went WAY above and beyond to make sure it was not them. They rewired EVERYTHING which did solve internet drops. Computer to computer connections are garbage Cannot get switch at 5 to work, yet other at 4 has never had an issue. Direct connection, bypass switch, is good for DHCP and internet. DNS must be on server, not firewall. Cisco insists its my switches but as you can see I have used four and two different cables with the same result. My gut feeling is something is happening with routing. But I'm not smart enough to know that answer. I run a lot of VM's at 5-c-3, could that cause it? What's different compared to my previous house is I have introduced Gigabit hardware (firewall/switches/computers). Some of my computers might have IPv6 turned on if I haven't turned it off already. I'm truly at a loss and hope anyone has some crazy idea how to solve this. Bottom line, I need a switch in my office behind the firewall. I've changed everything. The real crux is I will find a working solution and, again, after days it will stop working. So this means I cannot isolate if its a computer since I have to use them. Oh and a solution is not throwing more money at this. I'm well into $1k already. Yah, lame.

  Read the article

• Cyrus on CentOS with sasl / pam / ldap

  - by Oscar

  SASL/PAM/LDAP is driving me crazy... that's what I read a lot when googling for problems in this area, and what I experience myself :-S I'm trying to get Cyrus imap working for virtual hosting on CentOS with this authorisation backend and really don't know what's happening. In saslauthd I configured the LDAP search filter to use, but it looks like pam completely ignores it. Here's what I do for testing (done more tests but all with similar results): [root@testserv ~]# imtest -u [email protected] -a [email protected] WARNING: no hostname supplied, assuming localhost S: * OK [CAPABILITY IMAP4 IMAP4rev1 LITERAL+ ID STARTTLS] testserv. Cyrus IMAP4 v2.3.7-Invoca-RPM-2.3.7-7.el5_6.4 server ready C: C01 CAPABILITY S: * CAPABILITY IMAP4 IMAP4rev1 LITERAL+ ID STARTTLS ACL RIGHTS=kxte QUOTA MAILBOX-REFERRALS NAMESPACE UIDPLUS NO_ATOMIC_RENAME UNSELECT CHILDREN MULTIAPPEND BINARY SORT SORT=MODSEQ THREAD=ORDEREDSUBJECT THREAD=REFERENCES ANNOTATEMORE CATENATE CONDSTORE IDLE LISTEXT LIST-SUBSCRIBED X-NETSCAPE URLAUTH S: C01 OK Completed Please enter your password: C: L01 LOGIN [email protected] {6} S: + go ahead C: <omitted> S: L01 NO Login failed: authentication failure Authentication failed. generic failure Security strength factor: 0 C: Q01 LOGOUT * BYE LOGOUT received Q01 OK Completed Connection closed. The LDAP entry does exist (and so does the mailbox in Cyrus): [root@testserv ~]# ldapsearch -WxD cn=Manager,o=mydomain,c=com [email protected] Enter LDAP Password: # extended LDIF # # LDAPv3 # base <> with scope subtree # filter: [email protected] # requesting: ALL # # myuser, accounts, testserv.mydomain.com, mydomain, com dn: uid=myuser,ou=accounts,dc=testserv.mydomain.com,o=mydomain,c=com objectClass: top objectClass: person objectClass: organizationalPerson objectClass: inetOrgPerson objectClass: posixAccount objectClass: shadowAccount uidNumber: 16 uid: myuser gidNumber: 5 givenName: My sn: Name mail: [email protected] cn: My Name userPassword:: dYN5ebB0fXhNRn1pZllhRnJX7Uk= shadowLastChange: 15176 homeDirectory: /dev/null # search result search: 2 result: 0 Success # numResponses: 2 # numEntries: 1 This is what I get in /var/log/messages Aug 2 04:00:11 testserv cyrus/imap[12514]: auxpropfunc error invalid parameter supplied Aug 2 04:00:19 testserv saslauthd[5926]: do_auth : auth failure: [[email protected]] [service=imap] [realm=testserv.mydomain.com] [mech=pam] [reason=PAM auth error] ... /var/adm/auth.log Aug 2 04:00:11 testserv cyrus/imap[12514]: auxpropfunc error invalid parameter supplied Aug 2 04:00:11 testserv cyrus/imap[12514]: _sasl_plugin_load failed on sasl_auxprop_plug_init for plugin: ldapdb Aug 2 04:00:19 testserv saslauthd[5926]: DEBUG: auth_pam: pam_authenticate failed: User not known to the underlying authentication module Aug 2 04:00:19 testserv saslauthd[5926]: do_auth : auth failure: [[email protected]] [service=imap] [realm=testserv.mydomain.com] [mech=pam] [reason=PAM auth error] (AFAIK I can ignore the auxprop msg) ... and /var/log/slapd.log: Aug 2 04:00:19 testserv slapd[5968]: conn=61 fd=27 ACCEPT from IP=127.0.0.1:51403 (IP=0.0.0.0:389) Aug 2 04:00:19 testserv slapd[5968]: conn=61 op=0 BIND dn="" method=128 Aug 2 04:00:19 testserv slapd[5968]: conn=61 op=0 RESULT tag=97 err=0 text= Aug 2 04:00:19 testserv slapd[5968]: conn=61 op=1 SRCH base="o=mydomain,c=com" scope=2 deref=0 filter="([email protected])" Aug 2 04:00:19 testserv slapd[5968]: conn=61 op=1 SEARCH RESULT tag=101 err=0 nentries=0 text= Aug 2 04:00:19 testserv slapd[5968]: conn=61 op=2 UNBIND Aug 2 04:00:19 testserv slapd[5968]: conn=61 fd=27 closed These are the settings in In /etc/imapd.conf: sasl_mech_list: PLAIN LOGIN sasl_pwcheck_method: saslauthd ## sasl_auxprop_plugin: sasldb sasl_auto_transition: no and my sasl config: [root@testserv ~]# cat /etc/sysconfig/saslauthd # Directory in which to place saslauthd's listening socket, pid file, and so # on. This directory must already exist. SOCKETDIR=/var/run/saslauthd # Mechanism to use when checking passwords. Run "saslauthd -v" to get a list # of which mechanism your installation was compiled with the ablity to use. MECH=pam # Additional flags to pass to saslauthd on the command line. See saslauthd(8) # for the list of accepted flags. FLAGS="-c -r -O /etc/saslauthd.conf" [root@testserv ~]# cat /etc/saslauthd.conf ldap_servers: ldap://127.0.0.1/ ldap_search_base: dc=%d,o=mydomain,c=com ldap_auth_method: bind #ldap_filter: (|(uid=%u)((&(mail=%u@%d)(accountStatus=active))) ldap_filter: (&(mail=%u@%d)(accountStatus=active)) ldap_debug: 1 ldap_version: 3 The accountStatus=active is not in ldap yet, but that doesn't make a difference since I don't see it in the filter... that's not the reason for the failure. The weird thing is, I do get an error when I rename or remove /etc/saslauthd.conf, but when the file exists it seems happily ignored... The filter in slapd.log seems to be taken from /etc/ldap.conf. Apart from some timers, that only contains: host 127.0.0.1 base o=mydomain,c=com pam_login_attribute mail Outcommenting the pam_login_attribute results in this filter in slapd.log: filter="([email protected])" Pam-imap looks like this: [root@testserv ~]# cat /etc/pam.d/imap auth required pam_ldap.so debug account required pam_ldap.so debug #auth sufficient pam_unix.so likeauth nullok #auth sufficient pam_ldap.so use_first_pass #auth required pam_deny.so #account sufficient pam_unix.so #account sufficient pam_ldap.so The outcommented stuff is because I don't have the cyrus admin user in Ldap; that's a Linux user. That works fine when uncommented, but I still need to play around with that a little and first I wanna get imap working. Finally nsswitch: [root@testserv ~]# cat /etc/nsswitch.conf # # /etc/nsswitch.conf # # An example Name Service Switch config file. This file should be # sorted with the most-used services at the beginning. # # The entry '[NOTFOUND=return]' means that the search for an # entry should stop if the search in the previous entry turned # up nothing. Note that if the search failed due to some other reason # (like no NIS server responding) then the search continues with the # next entry. # # Legal entries are: # # nisplus or nis+ Use NIS+ (NIS version 3) # nis or yp Use NIS (NIS version 2), also called YP # dns Use DNS (Domain Name Service) # files Use the local files # db Use the local database (.db) files # compat Use NIS on compat mode # hesiod Use Hesiod for user lookups # [NOTFOUND=return] Stop searching if not found so far # # To use db, put the "db" in front of "files" for entries you want to be # looked up first in the databases # # Example: #passwd: db files nisplus nis #shadow: db files nisplus nis #group: db files nisplus nis passwd: compat ldap group: compat ldap shadow: compat ldap hosts: files dns bootparams: nisplus [NOTFOUND=return] files ethers: files netmasks: files networks: files protocols: files rpc: files services: files netgroup: nisplus publickey: nisplus automount: files nisplus aliases: files nisplus Any info where to start looking will be greatly appreciated! Thnx in advance

  Read the article

• Postfix configuration - Uing virtual min but server is bouncing back my mail.

  - by brodiebrodie

  I have no experience in setting up postfix, and thought virtualmin minght do the legwork for me. Appears not. When I try to send mail to the domain (either [email protected] [email protected] or [email protected]) I get the following message returned This is the mail system at host dedq239.localdomain. I'm sorry to have to inform you that your message could not be delivered to one or more recipients. It's attached below. For further assistance, please send mail to <postmaster> If you do so, please include this problem report. You can delete your own text from the attached returned message. The mail system <[email protected]> (expanded from <[email protected]>): User unknown in virtual alias table Final-Recipient: rfc822; [email protected] Original-Recipient: rfc822;[email protected] Action: failed Status: 5.0.0 Diagnostic-Code: X-Postfix; User unknown in virtual alias table How can I diagnose the problem here? It seems that the mail gets to my server but the server fails to locally deliver the message to the correct user. (This is a guess, truthfully I have no idea what is happening). I have checked my virtual alias table and it seems to be set up correctly (I can post if this would be helpful). Can anyone give me a clue as to the next step? Thanks alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases broken_sasl_auth_clients = yes command_directory = /usr/sbin config_directory = /etc/postfix daemon_directory = /usr/libexec/postfix debug_peer_level = 2 html_directory = no local_recipient_maps = $virtual_mailbox_maps mailq_path = /usr/bin/mailq.postfix manpage_directory = /usr/share/man mydestination = $myhostname, localhost.$mydomain, localhost, $mydomain myorigin = $mydomain newaliases_path = /usr/bin/newaliases.postfix readme_directory = /usr/share/doc/postfix-2.3.3/README_FILES sample_directory = /usr/share/doc/postfix-2.3.3/samples sendmail_path = /usr/sbin/sendmail.postfix setgid_group = postdrop smtpd_recipient_restrictions = permit_mynetworks reject_unauth_destination smtpd_sasl_auth_enable = yes soft_bounce = no unknown_local_recipient_reject_code = 550 virtual_alias_maps = hash:/etc/postfix/virtual My mail log file (the last entry) Sep 30 15:13:47 dedq239 postfix/cleanup[7237]: 207C6B18158: message-id=<[email protected]> Sep 30 15:13:47 dedq239 postfix/qmgr[7177]: 207C6B18158: from=<[email protected]>, size=1805, nrcpt=1 (queue active) Sep 30 15:13:47 dedq239 postfix/error[7238]: 207C6B18158: to=<[email protected]>, orig_to=<[email protected]>, relay=none, delay=0.64, delays=0.61/0.01/0/0.02, dsn=5.0.0, status=bounced (User unknown in virtual alias table) Sep 30 15:13:47 dedq239 postfix/cleanup[7237]: 8DC13B18169: message-id=<[email protected]> Sep 30 15:13:47 dedq239 postfix/qmgr[7177]: 8DC13B18169: from=<>, size=3691, nrcpt=1 (queue active) Sep 30 15:13:47 dedq239 postfix/bounce[7239]: 207C6B18158: sender non-delivery notification: 8DC13B18169 Sep 30 15:13:47 dedq239 postfix/qmgr[7177]: 207C6B18158: removed Sep 30 15:13:48 dedq239 postfix/smtp[7240]: 8DC13B18169: to=<[email protected]>, relay=gmail-smtp-in.l.google.com[209.85.216.55]:25, delay=1.3, delays=0.02/0.01/0.58/0.75, dsn=2.0.0, status=sent (250 2.0.0 OK 1254348828 36si15082901pxi.91) Sep 30 15:13:48 dedq239 postfix/qmgr[7177]: 8DC13B18169: removed Sep 30 15:14:17 dedq239 postfix/smtpd[7233]: disconnect from mail-bw0-f228.google.com[209.85.218.228] etc.aliases file below I have not touched this file - myvirtualdomain is a replacement for my real domain name # Aliases in this file will NOT be expanded in the header from # Mail, but WILL be visible over networks or from /bin/mail. # # >>>>>>>>>> The program "newaliases" must be run after # >> NOTE >> this file is updated for any changes to # >>>>>>>>>> show through to sendmail. # # Basic system aliases -- these MUST be present. mailer-daemon: postmaster postmaster: root # General redirections for pseudo accounts. bin: root daemon: root adm: root lp: root sync: root shutdown: root halt: root mail: root news: root uucp: root operator: root games: root gopher: root ftp: root nobody: root radiusd: root nut: root dbus: root vcsa: root canna: root wnn: root rpm: root nscd: root pcap: root apache: root webalizer: root dovecot: root fax: root quagga: root radvd: root pvm: root amanda: root privoxy: root ident: root named: root xfs: root gdm: root mailnull: root postgres: root sshd: root smmsp: root postfix: root netdump: root ldap: root squid: root ntp: root mysql: root desktop: root rpcuser: root rpc: root nfsnobody: root ingres: root system: root toor: root manager: root dumper: root abuse: root newsadm: news newsadmin: news usenet: news ftpadm: ftp ftpadmin: ftp ftp-adm: ftp ftp-admin: ftp www: webmaster webmaster: root noc: root security: root hostmaster: root info: postmaster marketing: postmaster sales: postmaster support: postmaster # trap decode to catch security attacks decode: root # Person who should get root's mail #root: marc abuse-myvirtualdomain.com: [email protected] My etc/postfix/virtual file is below - again myvirtualdomain is a replacement. I think this file was generated by Virtualmin and I have tried messing around with is with no success... This is the version without my changes. myunixusername@myvirtualdomain .com myunixusername myvirtualdomain .com myvirtualdomain.com [email protected] [email protected] [email protected] [email protected] [email protected] [email protected] [email protected] [email protected]

  Read the article

• What Apache/PHP configurations do you know and how good are they?

  - by FractalizeR

  Hello. I wanted to ask you about PHP/Apache configuration methods you know, their pros and cons. I will start myself: ---------------- PHP as Apache module---------------- Pros: good speed since you don't need to start exe every time especially in mpm-worker mode. You can also use various PHP accelerators in this mode like APC or eAccelerator. Cons: if you are running apache in mpm-worker mode, you may face stability issues because every glitch in any php script will lead to unstability to the whole thread pool of that apache process. Also in this mode all scripts are executed on behalf of apache user. This is bad for security. mpm-worker configuration requires PHP compiled in thread-safe mode. At least CentOS and RedHat default repositories doesn't have thread-safe PHP version so on these OSes you need to compile at least PHP yourself (there is a way to activate worker mpm on Apache). The use of thread-safe PHP binaries is considered experimental and unstable. Plus, many PHP extensions does not support thread-safe mode or were not well-tested in thread-safe mode. ---------------- PHP as CGI ---------------- This seems to be the slowest default configuration which seems to be a "con" itself ;) ---------------- PHP as CGI via mod_suphp ---------------- Pros: suphp allows you to execute php scipts on behalf of the script file owner. This way you can securely separate different sites on the same machine. Also, suphp allows to use different php.ini files per virtual host. Cons: PHP in CGI mode means less performance. In this mode you can't use php accelerators like APC because each time new process is spawned to handle script rendering the cache of previous process useless. BTW, do you know the way to apply some accelerator in this config? I heard something about using shm for php bytecode cache. Also, you cannot configure PHP via .htaccess files in this mode. You will need to install PECL htscanner for this if you need to set various per-script options via .htaccess (php_value / php_flag directives) ---------------- PHP as CGI via suexec ---------------- This configuration looks the same as with suphp, but I heard, that it's slower and less safe. Almost same pros and cons apply. ---------------- PHP as FastCGI ---------------- Pros: FastCGI standard allows single php process to handle several scripts before php process is killed. This way you gain performance since no need to spin up new php process for each script. You can also use PHP accelerators in this configuration (see cons section for comment). Also, FCGI almost like suphp also allows php processes to be executed on behalf of some user. mod_fcgid seems to have the most complete fcgi support and flexibility for apache. Cons: The use of php accelerator in fastcgi mode will lead to high memory consumption because each PHP process will have his own bytecode cache (unless there is some accelerator that can use shared memory for bytecode cache. Is there such?). FastCGI is also a little bit complex to configure. You need to create various configuration files and make some configuration modifications. It seems, that fastcgi is the most stable, secure, fast and flexible PHP configuration, however, a bit difficult to be configured. But, may be, I missed something? Comments are welcome!

  Read the article

• Allow Incoming Responses Apache. On Ubuntu 11.10 - Curl

  - by Daniel Adarve

  I'm trying to get a Curl Response from an outside server, however I noticed I cant neither PING the server in question nor connect to it. I tried disabling the iptables firewall but I had no success. My server is running behind a Cisco Linksys WRTN310N Router with the DD-wrt firmware Installed. In which I already disabled the firewall. Here are my network settings: Ifconfig eth0 Link encap:Ethernet HWaddr 00:26:b9:76:73:6b inet addr:192.168.1.120 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::226:b9ff:fe76:736b/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:49713 errors:0 dropped:0 overruns:0 frame:0 TX packets:30987 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:52829022 (52.8 MB) TX bytes:5438223 (5.4 MB) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:341 errors:0 dropped:0 overruns:0 frame:0 TX packets:341 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:27604 (27.6 KB) TX bytes:27604 (27.6 KB) /etc/resolv.conf nameserver 192.168.1.1 /etc/nsswitch.com passwd: compat group: compat shadow: compat hosts: files dns networks: files protocols: db files services: db files ethers: db files rpc: db files netgroup: nis /etc/host.conf order hosts,bind multi on /etc/hosts 127.0.0.1 localhost 127.0.0.1 callcenter # The following lines are desirable for IPv6 capable hosts ::1 ip6-localhost ip6-loopback fe00::0 ip6-localnet ff00::0 ip6-mcastprefix ff02::1 ip6-allnodes ff02::2 ip6-allrouters /etc/network/interfaces # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address 192.168.1.120 netmask 255.255.255.0 network 192.168.1.1 broadcast 192.168.1.255 gateway 192.168.1.1 The Url to which im trying to get a connection to is https://www.veripayment.com/integration/index.php When I ping it on terminal heres what I get daniel@callcenter:~$ ping https://www.veripayment.com/integration/index.php ping: unknown host https://www.veripayment.com/integration/index.php daniel@callcenter:~$ ping www.veripayment.com PING www.veripayment.com (69.172.200.5) 56(84) bytes of data. --- www.veripayment.com ping statistics --- 2 packets transmitted, 0 received, 100% packet loss, time 1007ms PHP Function in codeigniter public function authorizePayment(){ //--------------------------------------------------- // Authorize a payment //--------------------------------------------------- // Get variables from POST array $post_str = "action=payment&business=" .urlencode($this->input->post('business')) ."&vericode=" .urlencode($this->input->post('vericode')) ."&item_name=" .urlencode($this->input->post('item_name')) ."&item_code=" .urlencode($this->input->post('item_code')) ."&quantity=" .urlencode($this->input->post('quantity')) ."&amount=" .urlencode($this->input->post('amount')) ."&cc_type=" .urlencode($this->input->post('cc_type')) ."&cc_number=" .urlencode($this->input->post('cc_number')) ."&cc_expdate=" .urlencode($this->input->post('cc_expdate_year')).urlencode($this->input->post('cc_expdate_month')) ."&cc_security_code=" .urlencode($this->input->post('cc_security_code')) ."&shipment=" .urlencode($this->input->post('shipment')) ."&first_name=" .urlencode($this->input->post('first_name')) ."&last_name=" .urlencode($this->input->post('last_name')) ."&address=" .urlencode($this->input->post('address')) ."&city=" .urlencode($this->input->post('city')) ."&state_or_province=" .urlencode($this->input->post('state_or_province')) ."&zip_or_postal_code=" .urlencode($this->input->post('zip_or_postal_code')) ."&country=" .urlencode($this->input->post('country')) ."&shipping_address=" .urlencode($this->input->post('shipping_address')) ."&shipping_city=" .urlencode($this->input->post('shipping_city')) ."&shipping_state_or_province=" .urlencode($this->input->post('shipping_state_or_province')) ."&shipping_zip_or_postal_code=".urlencode($this->input->post('shipping_zip_or_postal_code')) ."&shipping_country=" .urlencode($this->input->post('shipping_country')) ."&phone=" .urlencode($this->input->post('phone')) ."&email=" .urlencode($this->input->post('email')) ."&ip_address=" .urlencode($this->input->post('ip_address')) ."&website_unique_id=" .urlencode($this->input->post('website_unique_id')); // Send URL string via CURL $backendUrl = "https://www.veripayment.com/integration/index.php"; $this->curl->create($backendUrl); $this->curl->post($post_str); $return = $this->curl->execute(); $result = array(); // Explode array where blanks are found $resparray = explode(' ', $return); if ($resparray) { // save results into an array foreach ($resparray as $resp) { $keyvalue = explode('=', $resp); if(isset($keyvalue[1])){ $result[$keyvalue[0]] = str_replace('"', '', $keyvalue[1]); } } } return $result; } This gets an empty result array. This function however works well in the previous server where the script was hosted before. No modifications where made whatsoever Thanks in Advance

  Read the article

• Active directory authentication for Ubuntu Linux login and cifs mounting home directories...

  - by Jamie

  I've configured my Ubuntu 10.04 Server LTS Beta 2 residing on a windows network to authenticate logins using active directory, then mount a windows share to serve as there home directory. Here is what I did starting from the initial installation of Ubuntu. Download and install Ubuntu Server 10.04 LTS Beta 2 Get updates # sudo apt-get update && sudo apt-get upgrade Install an SSH server (sshd) # sudo apt-get install openssh-server Some would argue that you should "lock sshd down" by disabling root logins. I figure if your smart enough to hack an ssh session for a root password, you're probably not going to be thwarted by the addition of PermitRootLogin no in the /etc/ssh/sshd_config file. If your paranoid or not simply not convinced then edit the file or give the following a spin: # (grep PermitRootLogin /etc/ssh/sshd_conifg && sudo sed -ri 's/PermitRootLogin ).+/\1no/' /etc/ssh/sshd_conifg) || echo "PermitRootLogin not found. Add it manually." Install required packages # sudo apt-get install winbind samba smbfs smbclient ntp krb5-user Do some basic networking housecleaning in preparation for the specific package configurations to come. Determine your windows domain name, DNS server name, and IP address for the active directory server (for samba). For conveniance I set environment variables for the windows domain and DNS server. For me it was (my AD IP address was 192.168.20.11): # WINDOMAIN=mydomain.local && WINDNS=srv1.$WINDOMAIN If you want to figure out what your domain and DNS server is (I was contractor and didn't know the network) check out this helpful reference. The authentication and file sharing processes for the Windows and Linux boxes need to have their clocks agree. Do this with an NTP service, and on the server version of Ubuntu the NTP service comes installed and preconfigured. The network I was joining had the DNS server serving up the NTP service too. # sudo sed -ri "s/^(server[ \t]).+/\1$WINDNS/" /etc/ntp.conf Restart the NTP daemon # sudo /etc/init.d/ntp restart We need to christen the Linux box on the new network, this is done by editing the host file (replace the DNS of with the FQDN of the windows DNS): # sudo sed -ri "s/^(127\.0\.0\.1[ \t]).*/\1$(hostname).$WINDOMAIN localhost $(hostname)/" /etc/hosts Kerberos configuration. The instructions that follow here aren't to be taken literally: the values for MYDOMAIN.LOCAL and srv1.mydomain.local need to be replaced with what's appropriate for your network when you edit the files. Edit the (previously installed above) /etc/krb5.conf file. Find the [libdefaults] section and change (or add) the key value pair (and it is in UPPERCASE WHERE IT NEEDS TO BE): [libdefaults] default_realm = MYDOMAIN.LOCAL Add the following to the [realms] section of the file: MYDOMAIN.LOCAL = { kdc = srv1.mydomain.local admin_server = srv1.mydomain.local default_domain = MYDOMAIN.LOCAL } Add the following to the [domain_realm] section of the file: .mydomain.local = MYDOMAIN.LOCAL mydomain.local = MYDOMAIN.LOCAL Conmfigure samba. When it's all said done, I don't know where SAMBA fits in ... I used cifs to mount the windows shares ... regardless, my system works and this is how I did it. Replace /etc/samba/smb.conf (remember I was working from a clean distro of Ubuntu, so I wasn't worried about breaking anything): [global] security = ads realm = MYDOMAIN.LOCAL password server = 192.168.20.11 workgroup = MYDOMAIN idmap uid = 10000-20000 idmap gid = 10000-20000 winbind enum users = yes winbind enum groups = yes template homedir = /home/%D/%U template shell = /bin/bash client use spnego = yes client ntlmv2 auth = yes encrypt passwords = yes winbind use default domain = yes restrict anonymous = 2 Start and stop various services. # sudo /etc/init.d/winbind stop # sudo service smbd restart # sudo /etc/init.d/winbind start Setup the authentication. Edit the /etc/nsswitch.conf. Here are the contents of mine: passwd: compat winbind group: compat winbind shadow: compat winbind hosts: files dns networks: files protocols: db files services: db files ethers: db files rpc: db files Start and stop various services. # sudo /etc/init.d/winbind stop # sudo service smbd restart # sudo /etc/init.d/winbind start At this point I could login, home directories didn't exist, but I could login. Later I'll come back and add how I got the cifs automounting to work. Numerous resources were considered so I could figure this out. Here is a short list (a number of these links point to mine own questions on the topic): Samba Kerberos Active Directory WinBind Mounting Linux user home directories on CIFS server Authenticating OpenBSD against Active Directory How to use Active Directory to authenticate linux users Mounting windows shares with Active Directory permissions Using Active Directory authentication with Samba on Ubuntu 9.10 server 64bit How practical is to authenticate a Linux server against AD? Auto-mounting a windows share on Linux AD login

  Read the article

• Windows 7 Machine Makes Router Drop -All- Wireless Connections [closed]

  - by Hammer Bro.

  Note: I accidentally originally posted this question over at SuperUser, and I still think the issue is caused by some low-level networking practice of Windows 7, but I think the expertise here would be more apt to figuring it out. Apologies for the cross-post. Some background: My home network consists of my Desktop, a two-month old Windows 7 (x64) machine which is online most frequently (N-spec), as well as three other Windows XP laptops (all G) that only connect every now and then (one for work, one for Netflix, and the other for infrequent regular laptop uses). I used to have a Belkin F5D8236-4 wireless router, and everything worked great. A week ago, however, I found out that the Belkin absolutely in no way would establish a VPN connection, something that has become important for work. So I bought a Netgear WNR3500v2/U/L. The wireless was acting a little sketchy at first for just the Windows 7 machine, but I thought it had something to do with 802.11N and I was in a hurry so I just fished up an ethernet cable and disabled the computer's wireless. It has now become apparent, though, that whenever the Windows 7 machine is connected to the router, all wireless connections become unstable. I was using my work laptop for a solid six hours today with no trouble, having multiple SSH connections open over VPN and streaming internet radio in the background. Then, within two minutes of turning on this Windows 7 box, I had lost all connectivity over the wireless. And I was two feet away from the router. The same sort of thing happens on all of the other laptops -- Netflix can be playing stuff all weekend, but if I come up here and do things on this (W7) computer, the streaming will be dead within ten minutes. So here are my basic observations: If the Windows 7 machine is off, then all connections will have a Signal Strength of Very Good or Excellent and a Speed of 48-54 Mbps for an indefinite amount of time. Shortly after the Windows 7 machine is turned on, all wireless connections will experience a consistent decline in Speed down to 1.0 Mbps, eventually losing their connection entirely. These machines will continue to maintain 70% signal strength, as observed by themselves and router. Once dropped, a wireless connection will have difficulty reconnecting. And, if a connection manages to become established, it will quickly drop off again. The Windows 7 machine itself will continue to function just fine if it's using a wired connection, although it will experience these same issues over the wireless. All of the drivers and firmwares are up to date, and this happened both with the stock Netgear firmware as well as the (current) DD-WRT. What I've tried: Making sure each computer is being assigned a distinct IP. (They are.) Disabling UPnP and Stateful Packet Inspection on the router. Disabling Network Sharing, SSDP Discovery, TCP/IP NetBios Helper and Computer Browser services on the Windows 7 machine. Disabling QoS Packet Scheduler, IPv6, and Link Layer Topology Discovery options on my ethernet controller (leaving only Client for Microsoft Networks, File and Printer Sharing, and IPv4 enabled). What I think: It seems awfully similar to the problems discussed in detail at http://social.msdn.microsoft.com/Forums/en/wsk/thread/1064e397-9d9b-4ae2-bc8e-c8798e591915 (which was both the most relevant and concrete information I could dig up on the internet). I still think that something the Windows 7 IP stack (or just Operating System itself) is doing is giving the router fits. However, I could be wrong, because I have two key differences. One is that most instances of this problem are reported as the entire router dying or restarting, and mine still works just fine over the wired connection. The other is that it's a new router, tested with both the factory firmware and the (I assume) well-maintained DD-WRT project. Even if Windows 7 is still secretly sending IPv6 packets or the TCP Window Scaling implementation that I hear Vista caused some trouble with (even though I've tried my best to disable anything fancy), this router should support those functions. I don't want to get a new or a replacement router unless someone can convince me that this is a defective unit. But the problem seems too specific and predictable by my instincts to be a hardware hiccup. And I don't want to deal with the inevitable problems that always seem to take half a day to resolve when getting a new router, since I'm frantically working (including tomorrow) to complete a project by next week's deadline. Plus, I think in the worst case scenario, I could keep this router connected directly to the modem, disable its wireless entirely, and connect the old Belkin to it directly. That should allow me to still use VPN (although I'll have to plug my work laptop directly into that router), and then maintain wireless connections for all of the other computers. But that feels so wrong to me. Anyone have any ideas what the cause and possible solution could be? Clarifications: The Windows 7 machine is directly connected via an ethernet cable to the router for everything above. But while it is online, all other computers' wireless connections become unusable. It is not an issue of signal strength or interference -- no other devices within scanning range are using Channel 1, and the problem will affect computers that are literally feet away from the router with 95% signal strength.

  Read the article

• Is Apache 2.2.22 able to sustain 1.000 simultaneous connected clients?

  - by Fnux

  For an article in a news paper, I'm benchmarking 5 different web servers (Apache2, Cherokee, Lighttpd, Monkey and Nginx). The tests made consist of measuring the execution times as well as different parameters such as the number of request served per second, the amount of RAM, the CPU used, during a growing load of simultaneous clients (from 1 to 1.000 with a step of 10) each client sending 1.000.000 requets of a small fixed file, then of a medium fixed file, then a small dynamic content (hello.php) and finally a complex dynamic content (the computation of the reimbursment of a loan). All the web servers are able to sustain such a load (up to 1.000 clients) but Apache2 which always stops to respond when the test reach 450 to 500 simultaneous clients. My configuration is : CPU: AMD FX 8150 8 cores @ 4.2 GHz RAM: 32 Gb. SSD: 2 x Crucial 240 Gb SATA6 OS: Ubuntu 12.04.3 64 bit WS: Apache 2.2.22 My Apache2 configuration is as follows: /etc/apache2/apache2.conf LockFile ${APACHE_LOCK_DIR}/accept.lock PidFile ${APACHE_PID_FILE} Timeout 30 KeepAlive On MaxKeepAliveRequests 1000000 KeepAliveTimeout 2 ServerName "fnux.net" <IfModule mpm_prefork_module> StartServers 16 MinSpareServers 16 MaxSpareServers 16 ServerLimit 2048 MaxClients 1024 MaxRequestsPerChild 0 </IfModule> User ${APACHE_RUN_USER} Group ${APACHE_RUN_GROUP} AccessFileName .htaccess <Files ~ "^\.ht"> Order allow,deny Deny from all Satisfy all </Files> DefaultType None HostnameLookups Off ErrorLog ${APACHE_LOG_DIR}/error.log LogLevel emerg Include mods-enabled/*.load Include mods-enabled/*.conf Include httpd.conf Include ports.conf LogFormat "%v:%p %h %l %u %t \"%r\" %>s %O \"%{Referer}i\" \"%{User-Agent}i\"" vhost_combined LogFormat "%h %l %u %t \"%r\" %>s %O \"%{Referer}i\" \"%{User-Agent}i\"" combined LogFormat "%h %l %u %t \"%r\" %>s %O" common LogFormat "%{Referer}i -> %U" referer LogFormat "%{User-agent}i" agent Include conf.d/ Include sites-enabled/ /etc/apache2/ports.conf NameVirtualHost *:8180 Listen 8180 <IfModule mod_ssl.c> Listen 443 </IfModule> <IfModule mod_gnutls.c> Listen 443 </IfModule> /etc/apache2/mods-available <IfModule mod_fastcgi.c> AddHandler php5-fcgi .php Action php5-fcgi /cgi-bin/php5.external <Location "/cgi-bin/php5.external"> Order Deny,Allow Deny from All Allow from env=REDIRECT_STATUS </Location> </IfModule> /etc/apache2/sites-available/default <VirtualHost *:8180> ServerAdmin webmaster@localhost DocumentRoot /var/www/apache2 <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/> Options Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog ${APACHE_LOG_DIR}/error.log LogLevel emerg ##### CustomLog ${APACHE_LOG_DIR}/access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> <IfModule mod_fastcgi.c> AddHandler php5-fcgi .php Action php5-fcgi /php5-fcgi Alias /php5-fcgi /usr/lib/cgi-bin/php5-fcgi FastCgiExternalServer /usr/lib/cgi-bin/php5-fcgi -host 127.0.0.1:9000 -pass-header Authorization </IfModule> </VirtualHost> /etc/security/limits.conf * soft nofile 1000000 * hard nofile 1000000 So, I would trully appreciate your advice to setup Apache2 to make it able to sustain 1.000 simultaneous clients, if this is even possible. TIA for your help. Cheers.

  Read the article

• Single-Signon options for Exchange 2010

  - by freiheit

  We're working on a project to migrate employee email from Unix/open-source (courier IMAP, exim, squirrelmail, etc) to Exchange 2010, and trying to figure out options for single-signon for Outlook Web Access. So far all the options I've found are very ugly and "unsupportable", and may simply not work with Forefront. We already have JA-SIG CAS for token-based single-signon and Shibboleth for SAML. Users are directed to a simple in-house portal (a Perl CGI, really) that they use to sign in to most stuff. We have an HA OpenLDAP cluster that's already synchronized against another AD domain and will be synchronized with the AD domain Exchange will be using. CAS authenticates against LDAP. The portal authenticates against CAS. Shibboleth authenticates with CAS but pulls additional data from LDAP. We're moving in the direction of having web services authenticate against CAS or Shibboleth. (Students are already on SAML/Shibboleth authenticated Google Apps for Education) With Squirrelmail we have a horrible hack linked to from that portal page that authenticates against CAS, gets your original plaintext password (yes, I know, evil), and gives you an HTTP form pre-filled with all the necessary squirrelmail login details with javaScript onLoad stuff to immediately submit the form. Trying to find out exactly what is possible with Exchange/OWA seems to be difficult. "CAS" is both the acronym for our single-signon server and an Exchange component. From what I've been able to tell there's an addon for Exchange that does SAML, but only for federating things like free/busy calendar info, not authenticating users. Plus it costs additional money so there's no way to experiment with it to see if it can be coaxed into doing what we want. Our plans for the Exchange cluster involve Forefront Threat Management Gateway (the new ISA) in the DMZ front-ending the CAS servers. So, the real question: Has anybody managed to make Exchange authenticate with CAS (token-based single-signon) or SAML, or with something I can reasonably likely make authenticate with one of those (such as anything that will accept apache's authentication)? With Forefront? Failing that, anybody have some tips on convincing OWA Forms Based Authentication (FBA) into letting us somehow "pre-login" the user? (log in as them and pass back cookies to the user, or giving the user a pre-filled form that autosubmits like we do with squirrelmail). This is the least-favorite option for a number of reasons, but it would (just barely) satisfy our requirements. From what I hear from the guy implementing Forefront, we may have to set OWA to basic authentication and do forms in Forefront for authentication, so it's possible this isn't even possible. I did find CasOwa, but it only mentions Exchange 2007, looks kinda scary, and as near as I can tell is mostly the same OWA FBA hack I was considering slightly more integrated with the CAS server. It also didn't look like many people had had much success with it. And it may not work with Forefront. There's also "CASifying Outlook Web Access 2", but that one scares me, too, and involves setting up a complex proxy config, which seems more likely to break. And, again, doesn't look like it would work with Forefront. Am I missing something with Exchange SAML (OWA Federated whatchamacallit) where it is possible to configure to do user authentication and not just free/busy access authorization?

  Read the article

• How to share internet over VPN and inside a virtual machine (Windows)?

  - by mountrix

  ` My final goal is to have a virtual machine at work in which anything that happen inside (tcp, udp, ping, ...) will use the Internet connection of a computer at home. So, if inside this VM should I open an Internet browser to a site such as "show my IP", my home IP should be printed. I am also looking for a way to debug/develop a software inside this VM, but I would like to tunnel only the connections of this software, not the full graphical interface, this is why a Remote Desktop solution won't fit me. The connection between the both computer should be secured somehow, like in a SSH tunnel. This ultimately should allow me to have a portable VM in which I can connect to whatever networks I have access at home, in a secure way. This is my configuration: At work, I have a LAN-connected desktop computer, with Windows 7 Professional Edition as a host [computer W] On this same computer, I have a Virtual Box machine running Windows XP [computer V] At home, I have a laptop computer, running Windows 7 Home Edition [computer H] This laptop is connected to a Livebox 2 broadband modem by Wifi. What I am trying to do is to sit at work in front of the virtual machine [V], and connect to a webpage as if the request was issued from the laptop [H] at home, and the data should be securely tunneled between the both. But if I am using internet directly inside [W], it should use the normal LAN interface at work. To achieve my goal, I first try using VPN, than SSH tunneling, without success. I first tried to install Teamviewer between [W] and [H]. This is working fine, I can send files, share desktop, etc. Teamviewer has a VPN mode that creates a new VPN network interface with its own IP, both on computer [W] and [H]. This allowed me to connect [H] as a network computer inside [W] and I was able to share files, but not to share Internet. At this point, I tried to use from [W] the Internet as if I was at home. I setup a route (using route add from command line in [W]) in order to instruct each packet going to a given website to pass by the new VPN interface on [W], with the hope it will be forwarded to [H], but the webpage was simply inaccessible. I then tried to setup a Windows VPN connection between [W] and [H], using the Windows 7 VPN feature. [H] was the server and [W] the client. But it failed: I got the "Unable to join a remote PC while trying to VPN" 720 Error when I was setting up the client on [W]. I think the problem is the Livebox 2 that could blocks the packets. But I am not sure of this: 1) with Teamviewer it works fine, 2) Livebox 2 has a configuration page for port mapping that gives the proper configuration to map VPN ports as an example so I guess that it should allow it, 3) I opened the ports 1723 (TCP) and 500 (UDP) according to some forums. Virtual box has a network configuration parameter in which I can use the VPN network interface created by Teamviewer as a bridged connection. This is suppose to work in the sense that all packets issued by the virtual machine [V] is supposed to go directly to [H]. But I had no internet connection inside [V]. Using the NAT mode, [V] has internet. For me this is the feature that I look for: filtering all connections from the virtual box application to the VPN network interface, and the remaining should use the normal LAN interface. Apart from the build-in feature of VBox, I even do not know if it is possible to route the packet from a given application to a given interface. Finally I tried also SSH tunneling, but this is not the solution I looked for. Using an external SSH server (Linux), I was able to create a localhost connection on [W] (or [V]), using something like 'ssh -N -D server[H]' in order to allow a web browser located in [W] to connect to any website using the SOCKS 5 proxy created locally (SOCKS is a build-in feature of SSH). But repeating the same operation on windows, using a windows SSH server inside [W] (I tried freeSSHd), it failed: SFTP worked, but not the SOCKS tunneling, it was like the browser in [H] did not find internet. Finally only Teamviewer looked able to create a VPN between [W] and [H], but I am not able to use it, as I want, I mean using the Internet connection of [H] sitting in front of [W]. I also tried to bridge the VPN interface and the wifi interface inside [H], but it blocked my laptop, and I tried also the Internet Connection Sharing, trying to share on [H] the wifi connection over the VPN interface. This fails also, but it seems because Teamviewer actually use the wifi interface to be able to provide the VPN link, so I guess I am creating a recursive loop. I do not know what to try next... Thank you for any advice!!

  Read the article

• vSphere ESX 5.5 hosts cannot connect to NFS Server

  - by Gerald

  Summary: My problem is I cannot use the QNAP NFS Server as an NFS datastore from my ESX hosts despite the hosts being able to ping it. I'm utilising a vDS with LACP uplinks for all my network traffic (including NFS) and a subnet for each vmkernel adapter. Setup: I'm evaluating vSphere and I've got two vSphere ESX 5.5 hosts (node1 and node2) and each one has 4x NICs. I've teamed them all up using LACP/802.3ad with my switch and then created a distributed switch between the two hosts with each host's LAG as the uplink. All my networking is going through the distributed switch, ideally, I want to take advantage of DRS and the redundancy. I have a domain controller VM ("Central") and vCenter VM ("vCenter") running on node1 (using node1's local datastore) with both hosts attached to the vCenter instance. Both hosts are in a vCenter datacenter and a cluster with HA and DRS currently disabled. I have a QNAP TS-669 Pro (Version 4.0.3) (TS-x69 series is on VMware Storage HCL) which I want to use as the NFS server for my NFS datastore, it has 2x NICs teamed together using 802.3ad with my switch. vmkernel.log: The error from the host's vmkernel.log is not very useful: NFS: 157: Command: (mount) Server: (10.1.2.100) IP: (10.1.2.100) Path: (/VM) Label (datastoreNAS) Options: (None) cpu9:67402)StorageApdHandler: 698: APD Handle 509bc29f-13556457 Created with lock[StorageApd0x411121] cpu10:67402)StorageApdHandler: 745: Freeing APD Handle [509bc29f-13556457] cpu10:67402)StorageApdHandler: 808: APD Handle freed! cpu10:67402)NFS: 168: NFS mount 10.1.2.100:/VM failed: Unable to connect to NFS server. Network Setup: Here is my distributed switch setup (JPG). Here are my networks. 10.1.1.0/24 VM Management (VLAN 11) 10.1.2.0/24 Storage Network (NFS, VLAN 12) 10.1.3.0/24 VM vMotion (VLAN 13) 10.1.4.0/24 VM Fault Tolerance (VLAN 14) 10.2.0.0/24 VM's Network (VLAN 20) vSphere addresses 10.1.1.1 node1 Management 10.1.1.2 node2 Management 10.1.2.1 node1 vmkernel (For NFS) 10.1.2.2 node2 vmkernel (For NFS) etc. Other addresses 10.1.2.100 QNAP TS-669 (NFS Server) 10.2.0.1 Domain Controller (VM on node1) 10.2.0.2 vCenter (VM on node1) I'm using a Cisco SRW2024P Layer-2 switch (Jumboframes enabled) with the following setup: LACP LAG1 for node1 (Ports 1 through 4) setup as VLAN trunk for VLANs 11-14,20 LACP LAG2 for my router (Ports 5 through 8) setup as VLAN trunk for VLANs 11-14,20 LACP LAG3 for node2 (Ports 9 through 12) setup as VLAN trunk for VLANs 11-14,20 LACP LAG4 for the QNAP (Ports 23 and 24) setup to accept untagged traffic into VLAN 12 Each subnet is routable to another, although, connections to the NFS server from vmk1 shouldn't need it. All other traffic (vSphere Web Client, RDP etc.) goes through this setup fine. I tested the QNAP NFS server beforehand using ESX host VMs atop of a VMware Workstation setup with a dedicated physical NIC and it had no problems. The ACL on the NFS Server share is permissive and allows all subnet ranges full access to the share. I can ping the QNAP from node1 vmk1, the adapter that should be used to NFS: ~ # vmkping -I vmk1 10.1.2.100 PING 10.1.2.100 (10.1.2.100): 56 data bytes 64 bytes from 10.1.2.100: icmp_seq=0 ttl=64 time=0.371 ms 64 bytes from 10.1.2.100: icmp_seq=1 ttl=64 time=0.161 ms 64 bytes from 10.1.2.100: icmp_seq=2 ttl=64 time=0.241 ms Netcat does not throw an error: ~ # nc -z 10.1.2.100 2049 Connection to 10.1.2.100 2049 port [tcp/nfs] succeeded! The routing table of node1: ~ # esxcfg-route -l VMkernel Routes: Network Netmask Gateway Interface 10.1.1.0 255.255.255.0 Local Subnet vmk0 10.1.2.0 255.255.255.0 Local Subnet vmk1 10.1.3.0 255.255.255.0 Local Subnet vmk2 10.1.4.0 255.255.255.0 Local Subnet vmk3 default 0.0.0.0 10.1.1.254 vmk0 VM Kernel NIC info ~ # esxcfg-vmknic -l Interface Port Group/DVPort IP Family IP Address Netmask Broadcast MAC Address MTU TSO MSS Enabled Type vmk0 133 IPv4 10.1.1.1 255.255.255.0 10.1.1.255 00:50:56:66:8e:5f 1500 65535 true STATIC vmk0 133 IPv6 fe80::250:56ff:fe66:8e5f 64 00:50:56:66:8e:5f 1500 65535 true STATIC, PREFERRED vmk1 164 IPv4 10.1.2.1 255.255.255.0 10.1.2.255 00:50:56:68:f5:1f 1500 65535 true STATIC vmk1 164 IPv6 fe80::250:56ff:fe68:f51f 64 00:50:56:68:f5:1f 1500 65535 true STATIC, PREFERRED vmk2 196 IPv4 10.1.3.1 255.255.255.0 10.1.3.255 00:50:56:66:18:95 1500 65535 true STATIC vmk2 196 IPv6 fe80::250:56ff:fe66:1895 64 00:50:56:66:18:95 1500 65535 true STATIC, PREFERRED vmk3 228 IPv4 10.1.4.1 255.255.255.0 10.1.4.255 00:50:56:72:e6:ca 1500 65535 true STATIC vmk3 228 IPv6 fe80::250:56ff:fe72:e6ca 64 00:50:56:72:e6:ca 1500 65535 true STATIC, PREFERRED Things I've tried/checked: I'm not using DNS names to connect to the NFS server. Checked MTU. Set to 9000 for vmk1, dvSwitch and Cisco switch and QNAP. Moved QNAP onto VLAN 11 (VM Management, vmk0) and gave it an appropriate address, still had same issue. Changed back afterwards of course. Tried initiating the connection of NAS datastore from vSphere Client (Connected to vCenter or directly to host), vSphere Web Client and the host's ESX Shell. All resulted in the same problem. Tried a path name of "VM", "/VM" and "/share/VM" despite not even having a connection to server. I plugged in a linux system (10.1.2.123) into a switch port configured for VLAN 12 and tried mounting the NFS share 10.1.2.100:/VM, it worked successfully and I had read-write access to it I tried disabling the firewall on the ESX host esxcli network firewall set --enabled false I'm out of ideas on what to try next. The things I'm doing differently from my VMware Workstation setup is the use of LACP with a physical switch and a virtual distributed switch between the two hosts. I'm guessing the vDS is probably the source of my troubles but I don't know how to fix this problem without eliminating it.

  Read the article

• CARP: two machines think they're the master, but only on one interface

  - by Conor McDermottroe

  I have two machines, each configured identically as a firewall/load balancer for a busy website. I have set them up with CARP and pfsync on both the internal and external interfaces. The internal interface is behaving as expected (primary listed as MASTER and secondary listed as BACKUP) On both machines, the network interfaces are as follows: em0 - External interface bge0 - Internal interface bge1 - Crossover connection between both machines carp0 - Shared external interface for CARP carp1 - Shared internal interface for CARP I've rewritten the IP addresses and MAC addresses below. The networks are as follows: 10.0.1.0/24 - External network 10.0.2.0/24 - Internal network 10.0.3.0/24 - Crossover network Here's the output from ifconfig on the primary: em0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=19b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,TSO4> ether [SNIP] inet 10.0.1.10 netmask 0xffffff00 broadcast 10.0.1.255 media: Ethernet 100baseTX <full-duplex> status: active bge0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=9b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM> ether [SNIP] inet 10.0.2.10 netmask 0xffffff00 broadcast 10.0.2.255 media: Ethernet 1000baseT <full-duplex> status: active bge1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=9b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM> ether [SNIP] inet 10.0.3.10 netmask 0xffffff00 broadcast 10.0.3.255 media: Ethernet 1000baseT <full-duplex> status: active lo0: flags=80c9<UP,LOOPBACK,RUNNING,NOARP,MULTICAST> metric 0 mtu 16384 options=3<RXCSUM,TXCSUM> inet6 fe80::1%lo0 prefixlen 64 scopeid 0x4 inet6 ::1 prefixlen 128 inet 127.0.0.1 netmask 0xff000000 pflog0: flags=141<UP,RUNNING,PROMISC> metric 0 mtu 33152 pfsync0: flags=0<> metric 0 mtu 1460 pfsync: syncdev: bge1 syncpeer: 10.0.3.11 maxupd: 128 carp0: flags=49<UP,LOOPBACK,RUNNING> metric 0 mtu 1500 inet 10.0.1.5 netmask 0xffffff00 carp: MASTER vhid 1 advbase 1 advskew 0 carp1: flags=49<UP,LOOPBACK,RUNNING> metric 0 mtu 1500 inet 10.0.2.5 netmask 0xffffff00 carp: MASTER vhid 2 advbase 1 advskew 0 And here's the /etc/rc.conf excerpt from the primary: defaultrouter="10.0.1.1" network_interfaces="em0 bge0 bge1 lo0 pfsync0" cloned_interfaces="carp0 carp1" ifconfig_em0="inet 10.0.1.10 netmask 255.255.255.0 media 100BaseTX mediaopt full-duplex" ifconfig_bge0="inet 10.0.2.10 netmask 255.255.255.0 media 1000BaseTX mediaopt full-duplex" ifconfig_bge1="inet 10.0.3.10 netmask 255.255.255.0 media 1000BaseTX mediaopt full-duplex" ifconfig_carp0="vhid 1 pass [SNIP] 10.0.1.5/24" ifconfig_carp1="vhid 2 pass [SNIP] 10.0.2.5/24" pfsync_enable="YES" pfsync_syncdev="bge1" pfsync_syncpeer="10.0.3.11" And here's the output on the secondary: em0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=19b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,TSO4> ether [SNIP] inet 10.0.1.11 netmask 0xffffff00 broadcast 10.0.1.255 media: Ethernet 100baseTX <full-duplex> status: active bge0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=9b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM> ether [SNIP] inet 10.0.2.11 netmask 0xffffff00 broadcast 10.0.2.255 media: Ethernet 1000baseT <full-duplex> status: active bge1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=9b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM> ether [SNIP] inet 10.0.3.11 netmask 0xffffff00 broadcast 10.0.3.255 media: Ethernet 1000baseT <full-duplex> status: active lo0: flags=80c9<UP,LOOPBACK,RUNNING,NOARP,MULTICAST> metric 0 mtu 16384 options=3<RXCSUM,TXCSUM> inet6 fe80::1%lo0 prefixlen 64 scopeid 0x4 inet6 ::1 prefixlen 128 inet 127.0.0.1 netmask 0xff000000 pflog0: flags=141<UP,RUNNING,PROMISC> metric 0 mtu 33152 pfsync0: flags=0<> metric 0 mtu 1460 pfsync: syncdev: bge1 syncpeer: 10.0.3.10 maxupd: 128 carp0: flags=49<UP,LOOPBACK,RUNNING> metric 0 mtu 1500 inet 10.0.1.5 netmask 0xffffff00 carp: MASTER vhid 1 advbase 1 advskew 20 carp1: flags=49<UP,LOOPBACK,RUNNING> metric 0 mtu 1500 inet 10.0.2.5 netmask 0xffffff00 carp: BACKUP vhid 2 advbase 1 advskew 20 And here's the /etc/rc.conf excerpt from the secondary: defaultrouter="10.0.1.1" network_interfaces="em0 bge0 bge1 lo0 pfsync0" cloned_interfaces="carp0 carp1" ifconfig_em0="inet 10.0.1.11 netmask 255.255.255.0 media 100BaseTX mediaopt full-duplex" ifconfig_bge0="inet 10.0.2.11 netmask 255.255.255.0 media 1000BaseTX mediaopt full-duplex" ifconfig_bge1="inet 10.0.3.11 netmask 255.255.255.0 media 1000BaseTX mediaopt full-duplex" ifconfig_carp0="vhid 1 pass [SNIP] advskew 20 10.0.1.5/24" ifconfig_carp1="vhid 2 pass [SNIP] advskew 20 10.0.2.5/24" pfsync_enable="YES" pfsync_syncdev="bge1" pfsync_syncpeer="10.0.3.10" What I don't understand is, the carp status on carp0 is MASTER on both machines when the status on carp1 is as it should be (MASTER on the primary and BACKUP on the secondary). What am I missing? Where should I be looking for clues?

  Read the article

• Backup a hosted Sharepoint

  - by David Mackintosh

  One of my customers has outsourced their Sharepoint and Exchange services to a hosted services provider. I believe it is a Sharepoint 2007 service. It is a shared hosting solution, so we do not have any kind of access to the server itself; we only have user-level and sharepoint-administrator-level access to the Sharepoint application. They have come to the point where they would like to have a copy of everything that is on the Sharepoint server. I have downloaded the Office Sharepoint Designer 2007, and it features three (!) ways to backup a Sharepoint server, none (!) of which work for me: File-Export-Personal Web Package: When selecting everything, it calculates a negative size. Barfs with No "content-type" in CGI environment error. File-Export-Sharepoint Template: barfs with a A World Wide Web browser, such as Windows Internet Explorer, is required to use this feature error. Site-Administration-Backup Web Site: wants to create the backup .cmp file on the sharepoint server itself. I don't have access to any servers on the same network so I can't redirect it to any form of the suggested \\server\place. Barfs with a The Web application at $URL could not be found. [...] error. Possibly moot because Google tells me that bad things happen using OSD to back up sites larger than 24MB (which this site is most definitely). So I called the helpdesk of the outsource provider, and got told that they recommend using OSD, but no they don't actually provide any application support for OSD (not that I blame them for that), but they could do a stsadm.exe backup and provide us with that, and OSD should be able to read the resulting cmp file. Then for authorization reasons they had my customer call them directly (since I can't authorize such an operation), and they told him that he didn't want a stsadm.exe backup, he wanted to get into an 'explorer view' and deal with things that way (they were vague). Google hasn't been much help in figuring out what an 'explorer view' is, let alone how I bring one up. The end goal of this operation is to have a backup of the site as it exists (hopefully today, but shortly anyways) in such a format that we don't need another sharepoint server to restore it to. Ie we'd like to be able to pick individual content directly out of this backup. We are not excessively concerned with things like formatting. We just want the documents. This is a fairly complex site with multiple subsites and multiple folders per subsite, so sitting there and manually downloading each file isn't really going to happen if there is a better easier way. So, my questions: Is the stsadm.exe backup what I want? If not, what do I want? If I manage to convince them that I do want the stsadm.exe backup, can I pick files out of the resulting backup file with OSD? If OSD isn't going to let me extract individual files, is there a tool I can use that can?

  Read the article

• NMap route determination on Windows 7 x64

  - by user30772

  C:\Windows\system32>nmap --iflist Starting Nmap 6.01 ( http://nmap.org ) at 2012-08-31 06:51 Central Daylight Time ************************INTERFACES************************ DEV (SHORT) IP/MASK TYPE UP MTU MAC eth0 (eth0) fe80::797f:b9b6:3ee0:27b8/64 ethernet down 1500 5C:AC:4C:E9:2D:46 eth0 (eth0) 169.254.39.184/4 ethernet down 1500 5C:AC:4C:E9:2D:46 eth1 (eth1) fe80::5c02:7e48:8fbe:c7c9/64 ethernet down 1500 00:FF:3F:7C:7C:2B eth1 (eth1) 169.254.199.201/4 ethernet down 1500 00:FF:3F:7C:7C:2B eth2 (eth2) fe80::74e4:1ab7:1b7d:a0d0/64 ethernet up 1500 14:FE:B5:BA:8A:C3 eth2 (eth2) 10.0.0.0.253/24 ethernet up 1500 14:FE:B5:BA:8A:C3 eth3 (eth3) fe80::b03e:ddf5:bb5c:5f76/64 ethernet up 1500 00:50:56:C0:00:01 eth3 (eth3) 169.254.95.118/16 ethernet up 1500 00:50:56:C0:00:01 eth4 (eth4) fe80::b175:831d:e60:27b/64 ethernet up 1500 00:50:56:C0:00:08 eth4 (eth4) 192.168.153.1/24 ethernet up 1500 00:50:56:C0:00:08 lo0 (lo0) ::1/128 loopback up -1 lo0 (lo0) 127.0.0.1/8 loopback up -1 tun0 (tun0) fe80::100:7f:fffe/64 point2point down 1280 tun1 (tun1) (null)/0 point2point down 1280 tun2 (tun2) fe80::5efe:a9fe:5f76/128 point2point down 1280 tun3 (tun3) (null)/0 point2point down 1280 tun4 (tun4) fe80::5efe:c0a8:9901/128 point2point down 1280 tun5 (tun5) fe80::5efe:ac14:fd/128 point2point down 1280 DEV WINDEVICE eth0 \Device\NPF_{0024872A-5A41-42DF-B484-FB3D3ED3FCE9} eth0 \Device\NPF_{0024872A-5A41-42DF-B484-FB3D3ED3FCE9} eth1 \Device\NPF_{3F7C7C2B-9AF3-45BB-B96E-2F00143CC2F7} eth1 \Device\NPF_{3F7C7C2B-9AF3-45BB-B96E-2F00143CC2F7} eth2 \Device\NPF_{08116FE5-F0FF-498A-9BF1-515528C57C13} eth2 \Device\NPF_{08116FE5-F0FF-498A-9BF1-515528C57C13} eth3 \Device\NPF_{AA83C6CE-AB2E-4764-92D1-CDEAFBA7AD21} eth3 \Device\NPF_{AA83C6CE-AB2E-4764-92D1-CDEAFBA7AD21} eth4 \Device\NPF_{D0679889-E9D4-411D-BDC5-F4DDB758E151} eth4 \Device\NPF_{D0679889-E9D4-411D-BDC5-F4DDB758E151} lo0 <none> lo0 <none> tun0 <none> tun1 <none> tun2 <none> tun3 <none> tun4 <none> tun5 <none> **************************ROUTES************************** DST/MASK DEV GATEWAY 192.168.153.255/32 eth0 255.255.255.255/32 eth0 255.255.255.255/32 eth0 127.0.0.1/32 eth0 127.255.255.255/32 eth0 255.255.255.255/32 eth0 169.254.95.118/32 eth0 169.254.255.255/32 eth0 10.0.0.0.253/32 eth0 255.255.255.255/32 eth0 10.0.0.0.255/32 eth0 255.255.255.255/32 eth0 192.168.153.1/32 eth0 255.255.255.255/32 eth0 10.0.0.0.0/24 eth0 192.168.153.0/24 eth0 10.10.10.0/24 eth0 10.0.0.0.4 169.254.0.0/16 eth0 127.0.0.0/8 eth0 224.0.0.0/4 eth0 224.0.0.0/4 eth0 224.0.0.0/4 eth0 224.0.0.0/4 eth0 224.0.0.0/4 eth0 224.0.0.0/4 eth0 0.0.0.0/0 eth0 10.0.0.0.1 JMeterX - I worded that way in hopes of raising answer efficnecy, but that probably wasnt the smartest choice. IMHO the problem (could be a symptom) is that nmap retardedly chooses eth0 as the gateway interface for any and all networks. Here's the result: C:\Windows\system32>nmap 10.0.0.55 Starting Nmap 6.01 ( http://nmap.org ) at 2012-08-31 07:43 Central Daylight Time Note: Host seems down. If it is really up, but blocking our ping probes, try -Pn Nmap done: 1 IP address (0 hosts up) scanned in 0.95 seconds C:\Windows\system32>nmap -e eth2 10.0.0.55 Starting Nmap 6.01 ( http://nmap.org ) at 2012-08-31 07:44 Central Daylight Time Nmap scan report for esxy5.dionne.net (10.0.0.55) Host is up (0.00070s latency). Not shown: 991 filtered ports PORT STATE SERVICE 22/tcp open ssh 80/tcp open http 427/tcp open svrloc 443/tcp open https 902/tcp open iss-realsecure 5988/tcp closed wbem-http 5989/tcp open wbem-https 8000/tcp open http-alt 8100/tcp open xprint-server MAC Address: 00:1F:29:59:C7:03 (Hewlett-Packard Company) Nmap done: 1 IP address (1 host up) scanned in 5.29 seconds Just to be clear, this is what makes absolutly no sense to me whatsoever. For reference, I've included similar info from an Ubuntu (that works normally) vm on the affected host below. Jacked Windows 7 **************************ROUTES************************** DST/MASK DEV GATEWAY 192.168.153.255/32 eth0 255.255.255.255/32 eth0 255.255.255.255/32 eth0 127.0.0.1/32 eth0 127.255.255.255/32 eth0 255.255.255.255/32 eth0 169.254.95.118/32 eth0 169.254.255.255/32 eth0 10.0.0.0.253/32 eth0 255.255.255.255/32 eth0 10.0.0.0.255/32 eth0 255.255.255.255/32 eth0 192.168.153.1/32 eth0 255.255.255.255/32 eth0 10.0.0.0.0/24 eth0 192.168.153.0/24 eth0 10.10.10.0/24 eth0 10.0.0.0.4 169.254.0.0/16 eth0 127.0.0.0/8 eth0 224.0.0.0/4 eth0 224.0.0.0/4 eth0 224.0.0.0/4 eth0 224.0.0.0/4 eth0 224.0.0.0/4 eth0 224.0.0.0/4 eth0 0.0.0.0/0 eth0 10.0.0.0.1 Working Ubuntu VM root@ubuntu:~# nmap --iflist Starting Nmap 5.21 ( http://nmap.org ) at 2012-08-31 07:44 PDT ************************INTERFACES************************ DEV (SHORT) IP/MASK TYPE UP MAC lo (lo) 127.0.0.1/8 loopback up eth0 (eth0) 172.20.0.89/24 ethernet up 00:0C:29:0A:C9:35 eth1 (eth1) 192.168.225.128/24 ethernet up 00:0C:29:0A:C9:3F eth2 (eth2) 192.168.150.128/24 ethernet up 00:0C:29:0A:C9:49 **************************ROUTES************************** DST/MASK DEV GATEWAY 192.168.225.0/0 eth1 192.168.150.0/0 eth2 172.20.0.0/0 eth0 169.254.0.0/0 eth0 0.0.0.0/0 eth0 172.20.0.1 root@ubuntu:~# nmap esxy2 Starting Nmap 5.21 ( http://nmap.org ) at 2012-08-31 07:44 PDT Nmap scan report for esxy2 (172.20.0.52) Host is up (0.00036s latency). rDNS record for 172.20.0.52: esxy2.dionne.net Not shown: 994 filtered ports PORT STATE SERVICE 80/tcp open http 427/tcp closed svrloc 443/tcp open https 902/tcp closed iss-realsecure 8000/tcp open http-alt 8100/tcp open unknown MAC Address: 00:04:23:B1:FA:6A (Intel) Nmap done: 1 IP address (1 host up) scanned in 4.76 seconds

  Read the article

• IPTables masquerading with one NIC

  - by Tuinslak

  Hi, I am running an OpenVPN server with only one NIC. This is my current layout: public.ip > Cisco firewall > lan.ip > OpenVPN server lan.ip = 192.168.22.70 The Cisco firewall forwards the requests to the oVPN server, thus so far everything works and clients are able to connect. However, all clients connected should be able to access 3 networks: lan1: 192.168.200.0 (vpn lan) > tun0 lan2: 192.168.110.0 (office lan) > eth1 (gw 192.168.22.1) lan3: 192.168.22.0 (server lan) > eth1 (broadcast network) So tun0 is mapped to eth1. Iptables output: # iptables-save # Generated by iptables-save v1.4.2 on Wed Feb 16 14:14:20 2011 *filter :INPUT ACCEPT [327:26098] :FORWARD DROP [305:31700] :OUTPUT ACCEPT [291:27378] -A INPUT -i lo -j ACCEPT -A INPUT -i tun0 -j ACCEPT -A INPUT -i ! tun0 -p udp -m udp --dport 67 -j REJECT --reject-with icmp-port-unreachable -A INPUT -i ! tun0 -p udp -m udp --dport 53 -j REJECT --reject-with icmp-port-unreachable -A FORWARD -d 192.168.200.0/24 -i tun0 -j DROP -A FORWARD -s 192.168.200.0/24 -i tun0 -j ACCEPT -A FORWARD -d 192.168.200.0/24 -i eth1 -j ACCEPT COMMIT # Completed on Wed Feb 16 14:14:20 2011 # Generated by iptables-save v1.4.2 on Wed Feb 16 14:14:20 2011 *nat :PREROUTING ACCEPT [302:26000] :POSTROUTING ACCEPT [3:377] :OUTPUT ACCEPT [49:3885] -A POSTROUTING -o eth1 -j MASQUERADE COMMIT # Completed on Wed Feb 16 14:14:20 2011 Yet, clients are unable to ping any ip (including 192.168.200.1, which is the oVPN's IP) When the machine was directly connected to the internet, with 2 NICs, it was quite simply solved with masquerading and adding static routes in the oVPN client's config. However, as masquerading won't accept virtual interfaces (eth0:0, etc) I am unable to get masquerading to work again (and I'm not even sure whether I need virtual interfaces). Thanks. Edit: OpenVPN server: # ifconfig eth1 Link encap:Ethernet HWaddr ba:e6:64:ec:57:ac inet addr:192.168.22.70 Bcast:192.168.22.255 Mask:255.255.255.0 inet6 addr: fe80::b8e6:64ff:feec:57ac/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:6857 errors:0 dropped:0 overruns:0 frame:0 TX packets:4044 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:584046 (570.3 KiB) TX bytes:473691 (462.5 KiB) Interrupt:14 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:334 errors:0 dropped:0 overruns:0 frame:0 TX packets:334 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:33773 (32.9 KiB) TX bytes:33773 (32.9 KiB) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:192.168.200.1 P-t-P:192.168.200.2 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) ifconfig on a client: # ifconfig eth0 Link encap:Ethernet HWaddr 00:22:64:71:11:56 inet addr:192.168.110.94 Bcast:192.168.110.255 Mask:255.255.255.0 inet6 addr: fe80::222:64ff:fe71:1156/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3466 errors:0 dropped:0 overruns:0 frame:0 TX packets:1838 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:997924 (974.5 KiB) TX bytes:332406 (324.6 KiB) Interrupt:17 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:37847 errors:0 dropped:0 overruns:0 frame:0 TX packets:37847 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2922444 (2.7 MiB) TX bytes:2922444 (2.7 MiB) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:192.168.200.30 P-t-P:192.168.200.29 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:689 errors:0 dropped:18 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 B) TX bytes:468778 (457.7 KiB) wlan0 Link encap:Ethernet HWaddr 00:16:ea:db:ae:86 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:704699 errors:0 dropped:0 overruns:0 frame:0 TX packets:730176 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:520385963 (496.2 MiB) TX bytes:225210422 (214.7 MiB) static routes line at the end of the client's config (I've been playing around with the 192.168.200.0 -- (un)commenting to see if anything changes): route 192.168.200.0 255.255.255.0 route 192.168.110.0 255.255.255.0 route 192.168.22.0 255.255.255.0 route on a vpn client: # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.200.29 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 192.168.22.0 192.168.200.29 255.255.255.0 UG 0 0 0 tun0 192.168.200.0 192.168.200.29 255.255.255.0 UG 0 0 0 tun0 192.168.110.0 192.168.200.29 255.255.255.0 UG 0 0 0 tun0 192.168.110.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 0.0.0.0 192.168.110.1 0.0.0.0 UG 0 0 0 eth0 edit: Weirdly enough, if I set push "redirect-gateway def1" in the server config, (and thus routes all traffic through VPN, which is not what I want), it seems to work.

  Read the article

• /usr/bin/sshd isn't linked against PAM on one of my systems. What is wrong and how can I fix it?

  - by marc.riera

  Hi, I'm using AD as my user account server with ldap. Most of the servers run with UsePam yes except this one, it has lack of pam support on sshd. root@linserv9:~# ldd /usr/sbin/sshd linux-vdso.so.1 => (0x00007fff621fe000) libutil.so.1 => /lib/libutil.so.1 (0x00007fd759d0b000) libz.so.1 => /usr/lib/libz.so.1 (0x00007fd759af4000) libnsl.so.1 => /lib/libnsl.so.1 (0x00007fd7598db000) libcrypto.so.0.9.8 => /usr/lib/libcrypto.so.0.9.8 (0x00007fd75955b000) libcrypt.so.1 => /lib/libcrypt.so.1 (0x00007fd759323000) libc.so.6 => /lib/libc.so.6 (0x00007fd758fc1000) libdl.so.2 => /lib/libdl.so.2 (0x00007fd758dbd000) /lib64/ld-linux-x86-64.so.2 (0x00007fd759f0e000) I have this packages installed root@linserv9:~# dpkg -l|grep -E 'pam|ssh' ii denyhosts 2.6-2.1 an utility to help sys admins thwart ssh hac ii libpam-modules 0.99.7.1-5ubuntu6.1 Pluggable Authentication Modules for PAM ii libpam-runtime 0.99.7.1-5ubuntu6.1 Runtime support for the PAM library ii libpam-ssh 1.91.0-9.2 enable SSO behavior for ssh and pam ii libpam0g 0.99.7.1-5ubuntu6.1 Pluggable Authentication Modules library ii libpam0g-dev 0.99.7.1-5ubuntu6.1 Development files for PAM ii openssh-blacklist 0.1-1ubuntu0.8.04.1 list of blacklisted OpenSSH RSA and DSA keys ii openssh-client 1:4.7p1-8ubuntu1.2 secure shell client, an rlogin/rsh/rcp repla ii openssh-server 1:4.7p1-8ubuntu1.2 secure shell server, an rshd replacement ii quest-openssh 5.2p1_q13-1 Secure shell root@linserv9:~# What I'm doing wrong? thanks. Edit: root@linserv9:~# cat /etc/pam.d/sshd # PAM configuration for the Secure Shell service # Read environment variables from /etc/environment and # /etc/security/pam_env.conf. auth required pam_env.so # [1] # In Debian 4.0 (etch), locale-related environment variables were moved to # /etc/default/locale, so read that as well. auth required pam_env.so envfile=/etc/default/locale # Standard Un*x authentication. @include common-auth # Disallow non-root logins when /etc/nologin exists. account required pam_nologin.so # Uncomment and edit /etc/security/access.conf if you need to set complex # access limits that are hard to express in sshd_config. # account required pam_access.so # Standard Un*x authorization. @include common-account # Standard Un*x session setup and teardown. @include common-session # Print the message of the day upon successful login. session optional pam_motd.so # [1] # Print the status of the user's mailbox upon successful login. session optional pam_mail.so standard noenv # [1] # Set up user limits from /etc/security/limits.conf. session required pam_limits.so # Set up SELinux capabilities (need modified pam) # session required pam_selinux.so multiple # Standard Un*x password updating. @include common-password Edit2: UsePAM yes fails With this configuration ssh fails to start : root@linserv9:/home/admmarc# cat /etc/ssh/sshd_config |grep -vE "^[ \t]*$|^#" Port 22 Protocol 2 ListenAddress 0.0.0.0 RSAAuthentication yes PubkeyAuthentication yes AuthorizedKeysFile .ssh/authorized_keys ChallengeResponseAuthentication yes UsePAM yes Subsystem sftp /usr/lib/sftp-server root@linserv9:/home/admmarc# The error it gives is as follows root@linserv9:/home/admmarc# /etc/init.d/ssh start * Starting OpenBSD Secure Shell server sshd /etc/ssh/sshd_config: line 75: Bad configuration option: UsePAM /etc/ssh/sshd_config: terminating, 1 bad configuration options ...fail! root@linserv9:/home/admmarc#

  Read the article

• OpenVPN (HideMyAss) client on Ubuntu: Route only HTTP traffic

  - by Andersmith

  I want to use HideMyAss VPN (hidemyass.com) on Ubuntu Linux to route only HTTP (ports 80 & 443) traffic to the HideMyAss VPN server, and leave all the other traffic (MySQL, SSH, etc.) alone. I'm running Ubuntu on AWS EC2 instances. The problem is that when I try and run the default HMA script, I suddenly can't SSH into the Ubuntu instance anymore and have to reboot it from the AWS console. I suspect the Ubuntu instance will also have trouble connecting to the RDS MySQL database, but haven't confirmed it. HMA uses OpenVPN like this: sudo openvpn client.cfg The client configuration file (client.cfg) looks like this: ############################################## # Sample client-side OpenVPN 2.0 config file # # for connecting to multi-client server. # # # # This configuration can be used by multiple # # clients, however each client should have # # its own cert and key files. # # # # On Windows, you might want to rename this # # file so it has a .ovpn extension # ############################################## # Specify that we are a client and that we # will be pulling certain config file directives # from the server. client auth-user-pass #management-query-passwords #management-hold # Disable management port for debugging port issues #management 127.0.0.1 13010 ping 5 ping-exit 30 # Use the same setting as you are using on # the server. # On most systems, the VPN will not function # unless you partially or fully disable # the firewall for the TUN/TAP interface. #;dev tap dev tun # Windows needs the TAP-Win32 adapter name # from the Network Connections panel # if you have more than one. On XP SP2, # you may need to disable the firewall # for the TAP adapter. ;dev-node MyTap # Are we connecting to a TCP or # UDP server? Use the same setting as # on the server. proto tcp ;proto udp # The hostname/IP and port of the server. # You can have multiple remote entries # to load balance between the servers. # All VPN Servers are added at the very end ;remote my-server-2 1194 # Choose a random host from the remote # list for load-balancing. Otherwise # try hosts in the order specified. # We order the hosts according to number of connections. # So no need to randomize the list # remote-random # Keep trying indefinitely to resolve the # host name of the OpenVPN server. Very useful # on machines which are not permanently connected # to the internet such as laptops. resolv-retry infinite # Most clients don't need to bind to # a specific local port number. nobind # Downgrade privileges after initialization (non-Windows only) ;user nobody ;group nobody # Try to preserve some state across restarts. persist-key persist-tun # If you are connecting through an # HTTP proxy to reach the actual OpenVPN # server, put the proxy server/IP and # port number here. See the man page # if your proxy server requires # authentication. ;http-proxy-retry # retry on connection failures ;http-proxy [proxy server] [proxy port #] # Wireless networks often produce a lot # of duplicate packets. Set this flag # to silence duplicate packet warnings. ;mute-replay-warnings # SSL/TLS parms. # See the server config file for more # description. It's best to use # a separate .crt/.key file pair # for each client. A single ca # file can be used for all clients. ca ./keys/ca.crt cert ./keys/hmauser.crt key ./keys/hmauser.key # Verify server certificate by checking # that the certicate has the nsCertType # field set to "server". This is an # important precaution to protect against # a potential attack discussed here: # http://openvpn.net/howto.html#mitm # # To use this feature, you will need to generate # your server certificates with the nsCertType # field set to "server". The build-key-server # script in the easy-rsa folder will do this. ;ns-cert-type server # If a tls-auth key is used on the server # then every client must also have the key. ;tls-auth ta.key 1 # Select a cryptographic cipher. # If the cipher option is used on the server # then you must also specify it here. ;cipher x # Enable compression on the VPN link. # Don't enable this unless it is also # enabled in the server config file. #comp-lzo # Set log file verbosity. verb 3 # Silence repeating messages ;mute 20 # Detect proxy auto matically #auto-proxy # Need this for Vista connection issue route-metric 1 # Get rid of the cached password warning #auth-nocache #show-net-up #dhcp-renew #dhcp-release #route-delay 0 120 # added to prevent MITM attack ns-cert-type server # # Remote servers added dynamically by the master server # DO NOT CHANGE below this line # remote-random remote 173.242.116.200 443 # 0 remote 38.121.77.74 443 # 0 # etc... remote 67.23.177.5 443 # 0 remote 46.19.136.130 443 # 0 remote 173.254.207.2 443 # 0 # END

  Read the article

• LXC Container Networking

  - by digitaladdictions

  I just started to experiment with LXC containers. I was able to create a container and start it up but I cannot get dhcp to assign the container an IP address. If I assign a static address the container can ping the host IP but not outside the host IP. The host is CentOS 6.5 and the guest is Ubuntu 14.04LTS. I used the template downloaded by lxc-create -t download -n cn-01 command. If I am trying to get an IP address on the same subnet as the host I don't believe I should need the IP tables rule for masquerading but I added it anyways. Same with IP forwarding. I compiled LXC by hand from the following source https://linuxcontainers.org/downloads/lxc-1.0.4.tar.gz Host Operating System Version #> cat /etc/redhat-release CentOS release 6.5 (Final) #> uname -a Linux localhost.localdomain 2.6.32-431.20.3.el6.x86_64 #1 SMP Thu Jun 19 21:14:45 UTC 2014 x86_64 x86_64 x86_64 GNU/Linux Container Config #> cat /usr/local/var/lib/lxc/cn-01/config # Template used to create this container: /usr/local/share/lxc/templates/lxc-download # Parameters passed to the template: # For additional config options, please look at lxc.container.conf(5) # Distribution configuration lxc.include = /usr/local/share/lxc/config/ubuntu.common.conf lxc.arch = x86_64 # Container specific configuration lxc.rootfs = /usr/local/var/lib/lxc/cn-01/rootfs lxc.utsname = cn-01 # Network configuration lxc.network.type = veth lxc.network.flags = up lxc.network.link = br0 LXC default.confu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:0c:29:12:30:f2 brd ff:ff:ff:ff:f #> cat /usr/local/etc/lxc/default.conf lxc.network.type = veth lxc.network.link = br0 lxc.network.flags = up #> lxc-checkconfig Kernel configuration not found at /proc/config.gz; searching... Kernel configuration found at /boot/config-2.6.32-431.20.3.el6.x86_64 --- Namespaces --- Namespaces: enabled Utsname namespace: enabled Ipc namespace: enabled Pid namespace: enabled User namespace: enabled Network namespace: enabled Multiple /dev/pts instances: enabled --- Control groups --- Cgroup: enabled Cgroup namespace: enabled Cgroup device: enabled Cgroup sched: enabled Cgroup cpu account: enabled Cgroup memory controller: /usr/local/bin/lxc-checkconfig: line 103: [: too many arguments enabled Cgroup cpuset: enabled --- Misc --- Veth pair device: enabled Macvlan: enabled Vlan: enabled File capabilities: /usr/local/bin/lxc-checkconfig: line 118: [: -gt: unary operator expected Note : Before booting a new kernel, you can check its configuration usage : CONFIG=/path/to/config /usr/local/bin/lxc-checkconfig Network Config (HOST) #> cat /etc/sysconfig/network-scripts/ifcfg-br0 DEVICE=br0 TYPE=Bridge BOOTPROTO=dhcp ONBOOT=yes #> cat /etc/sysconfig/network-scripts/ifcfg-eth0 DEVICE=eth0 ONBOOT=yes TYPE=Ethernet IPV6INIT=no USERCTL=no BRIDGE=br0 #> cat /etc/networks default 0.0.0.0 loopback 127.0.0.0 link-local 169.254.0.0 #> ip a s 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:0c:29:12:30:f2 brd ff:ff:ff:ff:ff:ff inet6 fe80::20c:29ff:fe12:30f2/64 scope link valid_lft forever preferred_lft forever 3: pan0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN link/ether 42:7e:43:b3:61:c5 brd ff:ff:ff:ff:ff:ff 4: br0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN link/ether 00:0c:29:12:30:f2 brd ff:ff:ff:ff:ff:ff inet 10.60.70.121/24 brd 10.60.70.255 scope global br0 inet6 fe80::20c:29ff:fe12:30f2/64 scope link valid_lft forever preferred_lft forever 12: vethT6BGL2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether fe:a1:69:af:50:17 brd ff:ff:ff:ff:ff:ff inet6 fe80::fca1:69ff:feaf:5017/64 scope link valid_lft forever preferred_lft forever #> brctl show bridge name bridge id STP enabled interfaces br0 8000.000c291230f2 no eth0 vethT6BGL2 pan0 8000.000000000000 no #> cat /proc/sys/net/ipv4/ip_forward 1 # Generated by iptables-save v1.4.7 on Fri Jul 11 15:11:36 2014 *nat :PREROUTING ACCEPT [34:6287] :POSTROUTING ACCEPT [0:0] :OUTPUT ACCEPT [0:0] -A POSTROUTING -o eth0 -j MASQUERADE COMMIT # Completed on Fri Jul 11 15:11:36 2014 Network Config (Container) #> cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback auto eth0 iface eth0 inet dhcp #> ip a s 11: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 02:69:fb:42:ee:d7 brd ff:ff:ff:ff:ff:ff inet6 fe80::69:fbff:fe42:eed7/64 scope link valid_lft forever preferred_lft forever 13: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever

  Read the article

• Can I use the same machine as a client and server for SSH?

  - by achraf

  For development tests, I need to setup an SFTP server. So I want to know if it's possible to use the same machine as the client and the server. I tried and I keep getting this error: > Permission denied (publickey). > Connection closed and by running ssh -v agharroud@localhost i get : > OpenSSH_3.8.1p1,OpenSSL 0.9.7d 17 Mar > debug1: Reading configuration data /etc/ssh_config > debug1: Connecting to localhost [127.0.0.1] port 22. > debug1: Connection established. > debug1: identity file /home/agharroud/.ssh/identity type -1 > debug1: identity file /home/agharroud/.ssh/id_rsa type 1 > debug1: identity file /home/agharroud/.ssh/id_dsa type -1 > debug1: Remote protocol version 2.0, remote software version OpenSSH_3.8.1p1 > debug1: match: OpenSSH_3.8.1p1 pat OpenSSH* > debug1: Enabling compatibility mode for protocol 2.0 > debug1: Local version string SSH-2.0-OpenSSH_3.8.1p1 > debug1: SSH2_MSG_KEXINIT sent > debug1: SSH2_MSG_KEXINIT received > debug1: kex:server->client aes128-cbc hmac-md5 none > debug1: kex: client->server aes128-cbc hmac-md5 none > debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent > debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP > debug1: SSH2_MSG_KEX_DH_GEX_INIT sent > debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY > debug1: Host 'localhost' is known and matches the RSA host key. > debug1: Found key in /home/agharroud/.ssh/known_hosts:1 > debug1: ssh_rsa_verify: signature correct > debug1: SSH2_MSG_NEWKEYS sent > debug1: expecting SSH2_MSG_NEWKEYS > debug1: SSH2_MSG_NEWKEYS received > debug1: SSH2_MSG_SERVICE_REQUEST sent > debug1: SSH2_MSG_SERVICE_ACCEPT > received > > ****USAGE WARNING**** > > This is a private computer system. This computer system, including all > related equipment, networks, and network devices (specifically > including Internet access) are provided only for authorized use. This > computer system may be monitored for all lawful purposes, including to > ensure that its use is authorized, for management of the system, to > facilitate protection against unauthorized access, and to verify > security procedures, survivability, and operational security. Monitoring > includes active attacks by authorized entities to test or verify the > security of this system. During monitoring, information may be > examined, recorded, copied and used for authorized purposes. All > information, including personal information, placed or sent over this > system may be monitored. > > Use of this computer system, authorized or unauthorized, > constitutes consent to monitoring of this system. Unauthorized use may > subject you to criminal prosecution. Evidence of unauthorized use collected > during monitoring may be used for administrative, criminal, or other > adverse action. Use of this system constitutes consent to monitoring for > these purposes. > > debug1: Authentications that can continue: publickey > debug1: Next authentication method: publickey > debug1: Trying private key:/home/agharroud/.ssh/identity > debug1: Offering public key:/home/agharroud/.ssh/id_rsa > debug1:Authentications that can continue:publickey > debug1: Trying private key:/home/agharroud/.ssh/id_dsa > debug1: No more authentication methods to try. > Permission denied (publickey). Any ideas about the problem ? thanks !

  Read the article

• Why am I unable to telnet to a local port that has a listening service?

  - by Skip Huffman

  I suspect this is either a very simple question, or a very complex one. I have a headless server running ubuntu 10.04 that I can ssh into. I have full root access to the system. I am trying to set up an ssh tunnel to allow me to vnc to the system (but that isn't my question. I have vnc running on port 5903, here is the netstat output for that: Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 0.0.0.0:5903 0.0.0.0:* LISTEN 7173/Xtightvnc tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN 465/sshd But when I try to telnet to that port, from within the same system and login, I get unable to connect errors # telnet localhost 5903 Trying ::1... Trying 127.0.0.1... telnet: Unable to connect to remote host: Connection timed out I am able to telnet to port 22 (as a verification) ~# telnet localhost 22 Trying ::1... Connected to localhost. Escape character is '^]'. SSH-2.0-OpenSSH_5.3p1 Debian-3ubuntu7 I have tried to open up any possible ports using ufw (probably clumsy fashion) # ufw status numbered Status: active To Action From -- ------ ---- [ 1] 5903 ALLOW IN Anywhere [ 2] 22 ALLOW IN Anywhere What else might be blocking this connection locally? Thank you, Edit: The only reference to port 5903 in iptable -L -n is this: Chain ufw-user-input (1 references) target prot opt source destination ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:5903 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:5903 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:22 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:22 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:8080 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:8080 I can post the whole output if that will be useful. hosts.allow and hosts.deny both contain only comments. Re-Edit: Some other questions pointed me to nmap, so I ran a portscan through that utility: # nmap -v -sT localhost -p1-65535 Starting Nmap 5.00 ( http://nmap.org ) at 2011-11-09 09:58 PST NSE: Loaded 0 scripts for scanning. Warning: Hostname localhost resolves to 2 IPs. Using 127.0.0.1. Initiating Connect Scan at 09:58 Scanning localhost (127.0.0.1) [65535 ports] Discovered open port 22/tcp on 127.0.0.1 Connect Scan Timing: About 18.56% done; ETC: 10:01 (0:02:16 remaining) Connect Scan Timing: About 44.35% done; ETC: 10:00 (0:01:17 remaining) Completed Connect Scan at 10:00, 112.36s elapsed (65535 total ports) Host localhost (127.0.0.1) is up (0.00s latency). Interesting ports on localhost (127.0.0.1): Not shown: 65533 filtered ports PORT STATE SERVICE 22/tcp open ssh 80/tcp closed http Read data files from: /usr/share/nmap Nmap done: 1 IP address (1 host up) scanned in 112.43 seconds Raw packets sent: 0 (0B) | Rcvd: 0 (0B) I think this shows that 5903 is blocked somehow. Which I pretty much knew. The question remains what is blocking it and how to modify. Re-re-edit: To check Paul Lathrop's suggested answer, I first verified my ip address with ifconfig: eth0 Link encap:Ethernet HWaddr 02:16:3e:42:28:8f inet addr:10.0.10.3 Bcast:10.0.10.255 Mask:255.255.255.0 Then tried to telnet to 5903 from that address: # telnet 10.0.10.3 5903 Trying 10.0.10.3... telnet: Unable to connect to remote host: Connection timed out No luck. Re-re-re-re-edit: Ok, I think I have isolated it a bit to vncserver, not the firewall, darn it. I shut off vncserver and had netcat listen on port 5903. My vnc client then was able to establish a connnection and sit and wait for a response. Looks like I should be chasing a vnc problem. At least that is progress Thanks for the help

  Read the article

• How to get attribute value using SelectSingleNode?

  - by Nano HE

  I am parsing a xml document, I need find out the gid (an attribute) value (3810). Based on SelectSingleNode(). I found it is not easy to find the attribute name and it's value. Can I use this method or I must switch to other way. Attached my code. How can I use book obj to get the attribute value3810 for gid. Thank you. My test.xml file as below <?xml version="1.0" ?> <root> <VersionInfo date="2007-11-28" version="1.0.0.2" /> <Attributes> <AttrDir name="EFEM" DirID="1"> <AttrDir name="Aligner" DirID="2"> <AttrDir name="SequenceID" DirID="3"> <AttrObj text="Slot01" gid="3810" unit="" scale="1" /> <AttrObjCount value="1" /> </AttrDir> </AttrDir> </AttrDir> </Attributes> </root> I wrote the test.cs as below public class Sample { public static void Main() { XmlDocument doc = new XmlDocument(); doc.Load("test.xml"); XmlNode book; XmlNode root = doc.DocumentElement; book = root.SelectSingleNode("Attributes[AttrDir[@name='EFEM']/AttrDir[@name='Aligner']/AttrDir[@name='SequenceID']/AttrObj[@text='Slot01']]"); Console.WriteLine("Display the modified XML document...."); doc.Save(Console.Out); } } [Update 06/10/2010] The xml file is a complex file. Included thousands of gids. But for each of Xpath, the gid is unique. I load the xml file to a TreeView control. this.treeView1.AfterSelect += new System.Windows.Forms.TreeViewEventHandler(this.treeView1_AfterSelect);. When treeView1_AfterSelect event occurred, the e.Node.FullPath will return as a String Value. I parse the string Value e.Node.FullPath. Then I got the member of XPath Above. Then I tried to find which gid item was selected. I need find the gid value as a return value indeed.

  Read the article

• AutoMapper recursive

  - by fra

  Hi! I would like to make a deep copy of a complex object tree using AutoMapper. The problem is that for each member I would like to construct a new object and then map it, and not simply copying the existing one. Here it is an example: public abstract class Test { public Test() { this.Id = Guid.NewGuid(); } public Guid Id { get; private set; } } public class OuterTest : Test { public InnerTest Inner { get; set; } } public class InnerTest : Test { public int Value { get; set; } } and how to test it: OuterTest outerDest = Mapper.Map<OuterTest, OuterTest>(outerSource); System.Diagnostics.Debug.WriteLine("InnerSource id: " + innerSource.Id); System.Diagnostics.Debug.WriteLine("InnerSource value: " + innerSource.Value); System.Diagnostics.Debug.WriteLine("OuterSource id: " + outerSource.Id); System.Diagnostics.Debug.WriteLine("OuterDest id: " + outerDest.Id); System.Diagnostics.Debug.WriteLine("OuterDest.Inner id: " + outerDest.Inner.Id); System.Diagnostics.Debug.WriteLine("OuterDest.Inner value: " + outerDest.Inner.Value); This is the result from the output window: InnerSource id: a60fda37-206a-40a8-a7f8-db480149c906 InnerSource value: 2119686684 OuterSource id: 7486899e-2da8-4873-9160-d6096b555c73 OuterDest id: 7486899e-2da8-4873-9160-d6096b555c73 OuterDest.Inner id: a60fda37-206a-40a8-a7f8-db480149c906 OuterDest.Inner value: 2119686684 The problem is thet the object innerSource is always the same instance as outerDest.Inner (I verified through MakeObjectId of VS debugger) but I would like them to be two different instances. How could I create a recursive map with this behavior? I tried creating a custom IValueResolver like the following, without success. public class AutoMapperNewObjectResolver : IValueResolver { public ResolutionResult Resolve(ResolutionResult source) { object resolved; if (source.Value != null) { object instance = Activator.CreateInstance(source.MemberType); resolved = Mapper.Map(source.Value, instance, source.MemberType, source.MemberType); } else { resolved = null; } ResolutionResult result = source.New(resolved, source.Context.DestinationType); return result; } } and configured like this: Mapper.CreateMap<OuterTest, OuterTest>() .ForMember(d => d.Inner, o => o.ResolveUsing<AutoMapperNewObjectResolver>().FromMember(src => src.Inner)); Any help appreciated, thank you

  Read the article

• System.ServiceModel.Syndication.SyndicationFeed throws when the RSS document includes a <script> blo

  - by Cheeso

  The code: using (XmlReader xmlr = XmlReader.Create(new StringReader(allXml))) { var items = from item in SyndicationFeed.Load(xmlr).Items select item; } The exception: Exception: System.Xml.XmlException: Unexpected node type Element. ReadElementString method can only be called on elements with simple or empty content. Line 11, position 25. at System.Xml.XmlReader.ReadElementString() at System.ServiceModel.Syndication.Rss20FeedFormatter.ReadXml(XmlReader reader, SyndicationFeed result) at System.ServiceModel.Syndication.Rss20FeedFormatter.ReadFeed(XmlReader reader) at System.ServiceModel.Syndication.Rss20FeedFormatter.ReadFrom(XmlReader reader) at System.ServiceModel.Syndication.SyndicationFeed.Load[TSyndicationFeed](XmlReader reader) at System.ServiceModel.Syndication.SyndicationFeed.Load(XmlReader reader) at Ionic.ToolsAndTests.ReadRss.Run() in c:\dev\dotnet\ReadRss.cs:line 90 The XML content: <?xml version="1.0" encoding="utf-8"?> <?xml-stylesheet type="text/xsl" href="https://www.ibm.com/developerworks/mydeveloperworks/blogs/roller-ui/styles/rss.xsl" media="screen"?><rss version="2.0" xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:atom="http://www.w3.org/2005/Atom" > <channel> <title>Software architecture, software engineering, and Renaissance Jazz</title> <link>https://www.ibm.com/developerworks/mydeveloperworks/blogs/gradybooch</link> <atom:link rel="self" type="application/rss+xml" href="https://www.ibm.com/developerworks/mydeveloperworks/blogs/gradybooch/feed/entries/rss?lang=en" /> <description>Software architecture, software engineering, and Renaissance Jazz</description> <language>en-us</language> <copyright>Copyright <script type='text/javascript'> document.write(blogsDate.date.localize (1273534889181));</script></copyright> <lastBuildDate>Mon, 10 May 2010 19:41:29 -0400</lastBuildDate> As you can see, on line 11, at position 25, there's a script block inside the <copyright> element. Other people have reported similar errors with other XML documents. The way I worked around this was to do a StreamReader.ReadToEnd, then do Regex.Replace on the result of that to yank out the script block, before passing the modified string to XmlReader.Create(). Feels like a hack. Has anyone got a better approach? I don't like this because I have to read in a 125k string into memory. Is it valid rss to include "complex content" like that - a script block inside an element?

  Read the article

< Previous Page | 237 238 239 240 241 242 243 244 245 246 247 248  | Next Page >