Search Results

Search found 7551 results on 303 pages for 'pre optimization'.

Page 244/303 | < Previous Page | 240 241 242 243 244 245 246 247 248 249 250 251  | Next Page >

• Configure static IPv6 on Ubuntu

  - by Charles Offenbacher

  I'm trying to configure IPv6 on a dedicated Ubuntu server. My provider gave me a "/64" (whatever that is - I'm still confused) of IPv6 addresses. However, when I try to use them, I can't ping anything. What do I do? :( # ping6 ipv6.google.com PING ipv6.google.com(vx-in-x63.1e100.net) 56 data bytes From fe80::219:d1ff:fefb:42d8 icmp_seq=1 Destination unreachable: Address unreachable From fe80::219:d1ff:fefb:42d8 icmp_seq=2 Destination unreachable: Address unreachable From fe80::219:d1ff:fefb:42d8 icmp_seq=3 Destination unreachable: Address unreachable --- ipv6.google.com ping statistics --- 3 packets transmitted, 0 received, +3 errors, 100% packet loss, time 2014ms # tracepath6 ipv6.google.com 1?: [LOCALHOST] 0.025ms pmtu 1500 1: fe80::219:d1ff:fefb:42d8%eth0 2000.022ms !H Resume: pmtu 1500 # cat /etc/network/interfaces # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address 64.***.***.*** netmask 255.255.255.248 gateway 64.***.***.*** iface eth0 inet6 static pre-up modprobe ipv6 address 2607:F878:1:***::1 netmask 64 gateway 2607:F878:1:***(same as address)::1 # ifconfig eth0 Link encap:Ethernet HWaddr 00:19:d1:fb:42:d8 inet addr:64.***.***.*** Bcast:64.***.***.*** Mask:255.255.255.248 inet6 addr: fe80::219:d1ff:fefb:42d8/64 Scope:Link inet6 addr: 2607:f878:1:***::1/64 Scope:Global UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:52451 errors:0 dropped:0 overruns:0 frame:0 TX packets:39729 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:6817761 (6.8 MB) TX bytes:6153835 (6.1 MB) Interrupt:41 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:166 errors:0 dropped:0 overruns:0 frame:0 TX packets:166 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:31714 (31.7 KB) TX bytes:31714 (31.7 KB)

  Read the article

• Merely installing PHP5 causes my AWS Ubuntu server to die minutes later from a massive CPU spike

  - by Mark Amery

  I have an AWS server with Ubuntu 11.04 as the OS that is running an Apache2 webserver (incidentally Python-based and using Django). We recently needed to add support for php5 to let us use a third party PHP library (incidentally for serving minified versions of js and css files). However, for no reason any of us can discern, if we simply run sudo apt-get install php5 on the server, then the install appears to finish successfully but, without us taking any further action (including not yet running sudo apt-get install libapache2-mod-php5, which I think would be the next step for us if everything worked), or actually running any PHP scripts on the server, a few minutes later the server becomes impossible to connect to, and looking at the 'Monitoring' tab for the server in the EC2 Management Console reveals that a while after the installation, CPU usage spikes to 100% and stays there permanently (until we reboot the server from the AWS Console). After rebooting, the server also reliably dies within a few (between 0 and 10) minutes. We restored the server to a pre-PHP state from an AMI Image, observed that it was stable, and then tried installing PHP5 again and observed the server die in exactly the same way, so we're pretty much certain that installing PHP5 is what causes the symptoms. What on earth could be causing this behaviour, and how can we get PHP installed on the server without it dying?

  Read the article

• Looking for issue tracker software for residential property management

  - by Rob

  This question is about a computer software (as per SU guidelines) application for centrally tracking issues concerning the management of a residental block of flats (apartments as they say in the US and France). Issues are incidents - and their resultant unplanned maintenance to address them, also planned one-off maintenance and also regular planned routine maintenance. I live in a block of flats (apartments), and along with other residents, are looking to more closely watch over issues with the communal, shared areas of the premises (corridors, courtyards, stairs, lifts, lights, trash/bin shed, bike stands, parking areas etc) and their maintenance, currently done by a property management company. Our own homes are our own affair internally, its the outside communal areas that I have the interest. The aim being to control costs and possibly reduce them, by proactively managing the property using historical data to predict issues and also to scrutinise maintenance charges against such data to ensure that the costs are as expected. Trending could also be established whereby recurrences of things can be detected and pre-empted to reduce costs. As a software professional, I'm aware of Bugzilla, eventum being free tools for software - which could be customised to fit this application, but wondered if there was something more appropriate. It might be useful for such software to be on a web server, with secure access, so that residents can log in and view the issues.

  Read the article

• How to make a Windows Vista boot / recovery cd from a running system without using an original CD / DVD

  - by Giorgio

  I have just repaired a friends computer (replaced motherboard) and now I am trying to repair the Windows (Windows Vista) partitions. Unfortunately, probably due to the fact that he tried to start it several times after the old motherboard had stopped working (no signal on video) now the partition table or the file systems (or both?) appear to be damaged. I managed to boot Windows a couple of times but could not complete the boot. I tried to repair the partition table and file systems using Linux RIP (booting from USB stick) but the Linux utilities say that the file system is damaged and I should run chkdsk /f from Windows. So I now need a Windows boot CD from which I can boot and run chkdsk or any other Windows utilities that can repair the file system. Is there an easy way to create such a CD? Or can I download it for free somewhere? All the links to Windows Vista boot / repair CD's I have found on the internet refer to non-free stuff. Any hint? EDIT I have a working laptop with Windows Vista installed. So one solution would be to make a bootable CD or USB from it so that I can boot the desktop and run the repair utilities. However, I do not have the Windows Vista installation DVD, because both computers were bought with Windows pre-installed.

  Read the article

• Using the same Windows 8 Upgrade installer on multiple PCs

  - by Karan

  As per this article: You may transfer the software to another computer that belongs to you. … You may not transfer the software to share licenses between computers. But what if I have a bunch of PCs with a mix of XP/Vista/Windows 7? Can I purchase either the Windows 8 Pro Upgrade $40 (download only) or $70 (DVD) version (both of which come without a key) only once and use it to upgrade all the PCs? Since I'm not sharing the license and each PC has its own valid genuine license, it should be allowed, right, or is it illegal? Even if they want people to shell out $40/$70 for each PC, how would they enforce the use of the installer/media on only one PC each? EDIT: I have been given to believe by a source that the installer will only check for the previous OS' key, which is what is confusing me (I have never purchased an upgrade version before this, only full retail or pre-installed versions). Is this true or will I need to enter two keys to make the upgrade work, one for the previous version and then one for Windows 8? If the latter is the case, then the issue is solved since obviously the same Windows 8 key will not be valid for multiple PCs.

  Read the article

• Use GRUB/GRUB2 to PXE boot OS image

  - by Jack

  Asked this in stackoverflow but they recommended I post this here: Here is the situation I am in: I currently have a Windows drive that boots XP. The BIOS does not support PXE booting so this is out of the question. Therefore, I was thinking I could install a customized GRUB bootloader on it instead such that it will have the option to PXE boot an image from a DHCP server connected to it and have the option to load Windows as it normally does (two items in menu). The catch is it may need to be automated (meaning no keyboard), so is there any way to run a script pre-boot during GRUB loading that determines if DHCP / TFTP servers are running and attempt to PXE boot an image from the network (and if not, say timeout of 10 seconds, regularly boot from Windows drive)? If this is not possible, what are some other options / suggestions? I was reading up on grub4dos as well but I'm not sure that is what I need. FWIW, I'm free to do whatever I want to the drive. I'd really appreciate some help on this as I'm not sure where to start. Thanks!

  Read the article

• How to autorun wpa_supplicant on Debian startup

  - by The Electric Muffin

  I'd like to run wpa_supplicant -D wext -i wlan0 -c /etc/wpa_supplicant.conf on Debian startup (runlevels 2-5). I found some vague instructions from a related question that said to put a script in /etc/init.d/ and then symlink to it from the apropriate /etc/rcRUNLEVEL.d/ directories. However, I noticed that there are already some files named "wpasupplicant" that probably run at startup: /etc/network/if-down.d/wpasupplicant /etc/network/if-post-down.d/wpasupplicant /etc/network/if-pre-up.d/wpasupplicant /etc/network/if-up.d/wpasupplicant They all are symlinks to the same script, /etc/wpa_supplicant/ifupdown.sh. It has a comment at the beginning saying it "[...] allows ifup(8), and ifdown(8) to manage wpa_supplicant(8) and wpa_cli(8) processes running in daemon mode." However, the closest it gets to calling wpa_supplicant itself is (in functions.sh): WPA_SUP_BIN="/sbin/wpa_supplicant" [snip] start-stop-daemon --start --oknodo $DAEMON_VERBOSITY \ --name $WPA_SUP_PNAME --startas $WPA_SUP_BIN --pidfile $WPA_SUP_PIDFILE \ -- $WPA_SUP_OPTIONS $WPA_SUP_CONF [snip] start-stop-daemon --stop --oknodo $DAEMON_VERBOSITY \ --exec $WPA_SUP_BIN --pidfile $WPA_SUP_PIDFILE Does that mean it's safe to make an init.d script for wpa_supplicant, and if so what would it look like? General info: Debian Squeeze (5.0) official wpasupplicant package (v0.6.10-2.1) The full contents of my system's functions.sh and ifupdown.sh are here (dependent, of course, on my system's uptime—it's a five-year-old laptop that greatly enjoys overheating): functions.sh ifupdown.sh

  Read the article

• How to disable monitor "sleep" on Ubuntu without access to X?

  - by exhuma

  I just received a CuBox (basically a tiny ARM based PC). It comes pre-installed with Ubuntu, and I did not (yet) want to fiddle with the OS itself. My aim is to have it automaticall start a browser in fullscrren upon boot. Using chromium with the "--kiosk" flag works perfectly in that regard. But now I have the problem that the screen turns off after a certain time. I managed to turn off the screen saver using: gconftool-2 -s /apps/gnome-screensaver/idle_activation_enabled --type=bool false And tried to turn off the power management using: gconftool-2 -s /apps/gnome-power-manager/ac_sleep_display --type=int 0 and gconftool-2 -s /apps/gnome-power-manager/timeout/sleep_display_ac --type=int 0 Neither of the power-management commands worked. Theoretically I could hook up a mouse and keyboard and configure it manually. But I want to learn how to do it over the console. The box will eventually be only reachable via SSH. So I'd like to be able to trouble-shoot it later. I don't quite know where to look for. I searched the gconf tree using gconftool-2 -S for anything related to the terms power, idle and sleep but did not find anything promising. Maybe it's not even gconf related... Any ideas what else I could look for?

  Read the article

• Error: could not create the Java Virtual Machine. Error: A fatal exception has occurred. Program will exit

  - by Gleeson9

  Pre-note: This is not a problem I am having with Minecraft. All answers I can find seem to be Minecraft issues. Error: could not create the Java Virtual Machine. Error: A fatal exception has occurred. Program will exit. I get this error when I try to do something Java related. I cannot launch a .jar without this error coming up and when I try to install JDK, I get this error. This has been plauging me for a while and I was not able to research an answer so I thought I would ask it myself. EDIT: Windows 7 (x64) Dell Studio Laptop, 4GB RAM, external Radeon HD 6950 Graphics Card. I have tried uninstalling all JVMs and reinstalling but it didn't work, although I cannot remember how thorough I was so I may try again. Here is a list of all the Java related things I have installed (found in the uninstall or change programs window): Java 3D 1.5.1 Java 3D 1.5.1 (x64) Java 3D 1.5.2 Java 6 Update 30 Java 6 Update 30 (64-bit) Java 7 Update 2 Java 7 Update 3 (64-bit) JavaFX 2.0.3 (64-bit) JavaFX 2.0.3 SDK (64-bit)

  Read the article

• Boot records messed on dual boot (win7 and ubuntu) machine with SSD and HDD

  - by Michael

  i have a lenovo ideapad y570 with two hard drives: SSD and normal HDD both managed by RapidDrive and windows 7 pre-installed. First, i have shrunk my 500 GB HDD a little bit to make some place for a linux installation. Then i installed linux mint 12 to it, also installed grub onto the drive (dev/sdb). Installation programm has not allowed me to install grub on sda. Then i replaced linux mint with ubuntu 12.04 but installed grub onto the SSD (which is dev/sda and was the default-option). After that i could boot into my windows, only ubuntu worked. So i did a research, and tried: rewriting mbr of windows into sda1, reinstalling grub, replacing grub2 with grub-legacy, and now i think my partitions table are totally messed. Here is fdisk -l output: ubuntu@ubuntu:~$ sudo fdisk -l Disk /dev/sda: 64.0 GB, 64023257088 bytes 255 heads, 63 sectors/track, 7783 cylinders, total 125045424 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sda1 * 2048 411647 204800 7 HPFS/NTFS/exFAT /dev/sda2 411648 1009430959 504509656 7 HPFS/NTFS/exFAT Disk /dev/sdb: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x5e5d1cc8 Device Boot Start End Blocks Id System /dev/sdb1 * 1979 884389887 442193954+ 12 Compaq diagnostics /dev/sdb2 884391934 976771071 46189569 5 Extended /dev/sdb5 884391936 937705471 26656768 83 Linux /dev/sdb6 937707520 967006207 14649344 83 Linux /dev/sdb7 967008256 976771071 4881408 82 Linux swap / Solaris I also cant mount any windows partitions to recover data. And when i open gparted, the whole sda-disk appears unallocated and it states "can not have a partition outside the disk!", also the end-sector address of /dev/sda2 confuses me. If i boot from the SSD, it throws some mbr error and wont boot, if i boot from the HDD, i only get the grub bash. How do i restore the partition tables? I can boot only from a live-cd at the machine. Thanks for any help.

  Read the article

• Redirecting or routing all traffic to OpenVPN on a Mac OS X client

  - by sdr56p

  I have configured an OpenVPN (2.2.1) server on an Ubuntu virtual machine in the Amazon elastic compute cloud. The server is up and running. I have installed OpenVPN (2.2.1) on a Mac OS X (10.8.2) client and I am using the openvpn2 binary to connect (in opposition to other clients like Tunnelblick or Viscosity). I can connect with the client and successfully ping or ssh the server through the tunnel. However, I can't redirect all internet traffic through the VPN even if I use the push "redirect-gateway def1 bypass-dhcp" option in the server.conf configurations. When I connect to the server with these configurations, I get a successful connection, but then an infinite series of error messages: "write UDPv4: No route to host (code=65)". Traffic routing seems to be compromised because I am not able to access anything anymore, not even the OpenVPN server (by pinging 10.8.0.1 for instance). This is beyond me. I am finding little help on the web and don't know what to try next. I don't think it is a problem of forwarding the traffic on the server since, first, I have also took care of that and, second, I can't even ping the VPN server locally through the tunnel (or ping anything at all for that matter). Thank you for your help. Here is the server.conf. file: port 1194 proto udp dev tun ca ca.crt cert ec2-server.crt key ec2-server.key # This file should be kept secret dh dh1024.pem server 10.8.0.0 255.255.255.0 ifconfig-pool-persist ipp.txt push "redirect-gateway def1 bypass-dhcp" client-to-client keepalive 10 120 comp-lzo persist-key persist-tun status openvpn-status.log verb 3 And the client.conf file: client dev tun proto udp remote servername.com 1194 resolv-retry infinite nobind persist-key persist-tun ca ca.crt cert Toto5.crt key Toto5.key ns-cert-type server comp-lzo verb 3 Here is the connection log with the error messages: $ sudo openvpn2 --config client.conf Wed Mar 13 22:58:22 2013 OpenVPN 2.2.1 x86_64-apple-darwin12.2.0 [SSL] [LZO2] [eurephia] built on Mar 4 2013 Wed Mar 13 22:58:22 2013 NOTE: OpenVPN 2.1 requires '--script-security 2' or higher to call user-defined scripts or executables Wed Mar 13 22:58:22 2013 LZO compression initialized Wed Mar 13 22:58:22 2013 Control Channel MTU parms [ L:1542 D:138 EF:38 EB:0 ET:0 EL:0 ] Wed Mar 13 22:58:22 2013 Socket Buffers: R=[196724->65536] S=[9216->65536] Wed Mar 13 22:58:22 2013 Data Channel MTU parms [ L:1542 D:1450 EF:42 EB:135 ET:0 EL:0 AF:3/1 ] Wed Mar 13 22:58:22 2013 Local Options hash (VER=V4): '41690919' Wed Mar 13 22:58:22 2013 Expected Remote Options hash (VER=V4): '530fdded' Wed Mar 13 22:58:22 2013 UDPv4 link local: [undef] Wed Mar 13 22:58:22 2013 UDPv4 link remote: 54.234.43.171:1194 Wed Mar 13 22:58:22 2013 TLS: Initial packet from 54.234.43.171:1194, sid=ffbaf343 d0c1a266 Wed Mar 13 22:58:22 2013 VERIFY OK: depth=1, /C=US/ST=CA/L=SanFrancisco/O=Fort-Funst ... ost.domain Wed Mar 13 22:58:22 2013 VERIFY OK: nsCertType=SERVER Wed Mar 13 22:58:22 2013 VERIFY OK: depth=0, /C=US/ST=CA/L=SanFrancisco/O=Fort-Funst ... ost.domain Wed Mar 13 22:58:23 2013 Data Channel Encrypt: Cipher 'BF-CBC' initialized with 128 bit key Wed Mar 13 22:58:23 2013 Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Wed Mar 13 22:58:23 2013 Data Channel Decrypt: Cipher 'BF-CBC' initialized with 128 bit key Wed Mar 13 22:58:23 2013 Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Wed Mar 13 22:58:23 2013 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 1024 bit RSA Wed Mar 13 22:58:23 2013 [ec2-server] Peer Connection Initiated with 54.234.43.171:1194 Wed Mar 13 22:58:25 2013 SENT CONTROL [ec2-server]: 'PUSH_REQUEST' (status=1) Wed Mar 13 22:58:25 2013 PUSH: Received control message: 'PUSH_REPLY,route 10.8.0.0 255.255.255.0,topology net30,ping 10,ping-restart 120,ifconfig 10.8.0.6 10.8.0.5' Wed Mar 13 22:58:25 2013 OPTIONS IMPORT: timers and/or timeouts modified Wed Mar 13 22:58:25 2013 OPTIONS IMPORT: --ifconfig/up options modified Wed Mar 13 22:58:25 2013 OPTIONS IMPORT: route options modified Wed Mar 13 22:58:25 2013 ROUTE default_gateway=0.0.0.0 Wed Mar 13 22:58:25 2013 TUN/TAP device /dev/tun0 opened Wed Mar 13 22:58:25 2013 /sbin/ifconfig tun0 delete ifconfig: ioctl (SIOCDIFADDR): Can't assign requested address Wed Mar 13 22:58:25 2013 NOTE: Tried to delete pre-existing tun/tap instance -- No Problem if failure Wed Mar 13 22:58:25 2013 /sbin/ifconfig tun0 10.8.0.6 10.8.0.5 mtu 1500 netmask 255.255.255.255 up Wed Mar 13 22:58:25 2013 /sbin/route add -net 10.8.0.0 10.8.0.5 255.255.255.0 add net 10.8.0.0: gateway 10.8.0.5 Wed Mar 13 22:58:25 2013 Initialization Sequence Completed ^CWed Mar 13 22:58:30 2013 event_wait : Interrupted system call (code=4) Wed Mar 13 22:58:30 2013 TCP/UDP: Closing socket Wed Mar 13 22:58:30 2013 /sbin/route delete -net 10.8.0.0 10.8.0.5 255.255.255.0 delete net 10.8.0.0: gateway 10.8.0.5 Wed Mar 13 22:58:30 2013 Closing TUN/TAP interface Wed Mar 13 22:58:30 2013 SIGINT[hard,] received, process exiting toto5:ttntec2 Dominic$ sudo openvpn2 --config client.conf --remote ec2-54-234-43-171.compute-1.amazonaws.com Wed Mar 13 22:58:57 2013 OpenVPN 2.2.1 x86_64-apple-darwin12.2.0 [SSL] [LZO2] [eurephia] built on Mar 4 2013 Wed Mar 13 22:58:57 2013 NOTE: OpenVPN 2.1 requires '--script-security 2' or higher to call user-defined scripts or executables Wed Mar 13 22:58:57 2013 LZO compression initialized Wed Mar 13 22:58:57 2013 Control Channel MTU parms [ L:1542 D:138 EF:38 EB:0 ET:0 EL:0 ] Wed Mar 13 22:58:57 2013 Socket Buffers: R=[196724->65536] S=[9216->65536] Wed Mar 13 22:58:57 2013 Data Channel MTU parms [ L:1542 D:1450 EF:42 EB:135 ET:0 EL:0 AF:3/1 ] Wed Mar 13 22:58:57 2013 Local Options hash (VER=V4): '41690919' Wed Mar 13 22:58:57 2013 Expected Remote Options hash (VER=V4): '530fdded' Wed Mar 13 22:58:57 2013 UDPv4 link local: [undef] Wed Mar 13 22:58:57 2013 UDPv4 link remote: 54.234.43.171:1194 Wed Mar 13 22:58:57 2013 TLS: Initial packet from 54.234.43.171:1194, sid=a0d75468 ec26de14 Wed Mar 13 22:58:58 2013 VERIFY OK: depth=1, /C=US/ST=CA/L=SanFrancisco/O=Fort-Funst ... ost.domain Wed Mar 13 22:58:58 2013 VERIFY OK: nsCertType=SERVER Wed Mar 13 22:58:58 2013 VERIFY OK: depth=0, /C=US/ST=CA/L=SanFrancisco/O=Fort-Funst ... ost.domain Wed Mar 13 22:58:58 2013 Data Channel Encrypt: Cipher 'BF-CBC' initialized with 128 bit key Wed Mar 13 22:58:58 2013 Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Wed Mar 13 22:58:58 2013 Data Channel Decrypt: Cipher 'BF-CBC' initialized with 128 bit key Wed Mar 13 22:58:58 2013 Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Wed Mar 13 22:58:58 2013 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 1024 bit RSA Wed Mar 13 22:58:58 2013 [ec2-server] Peer Connection Initiated with 54.234.43.171:1194 Wed Mar 13 22:59:00 2013 SENT CONTROL [ec2-server]: 'PUSH_REQUEST' (status=1) Wed Mar 13 22:59:00 2013 PUSH: Received control message: 'PUSH_REPLY,redirect-gateway def1 bypass-dhcp,route 10.8.0.0 255.255.255.0,topology net30,ping 10,ping-restart 120,ifconfig 10.8.0.6 10.8.0.5' Wed Mar 13 22:59:00 2013 OPTIONS IMPORT: timers and/or timeouts modified Wed Mar 13 22:59:00 2013 OPTIONS IMPORT: --ifconfig/up options modified Wed Mar 13 22:59:00 2013 OPTIONS IMPORT: route options modified Wed Mar 13 22:59:00 2013 ROUTE default_gateway=0.0.0.0 Wed Mar 13 22:59:00 2013 TUN/TAP device /dev/tun0 opened Wed Mar 13 22:59:00 2013 /sbin/ifconfig tun0 delete ifconfig: ioctl (SIOCDIFADDR): Can't assign requested address Wed Mar 13 22:59:00 2013 NOTE: Tried to delete pre-existing tun/tap instance -- No Problem if failure Wed Mar 13 22:59:00 2013 /sbin/ifconfig tun0 10.8.0.6 10.8.0.5 mtu 1500 netmask 255.255.255.255 up Wed Mar 13 22:59:00 2013 /sbin/route add -net 54.234.43.171 0.0.0.0 255.255.255.255 add net 54.234.43.171: gateway 0.0.0.0 Wed Mar 13 22:59:00 2013 /sbin/route add -net 0.0.0.0 10.8.0.5 128.0.0.0 add net 0.0.0.0: gateway 10.8.0.5 Wed Mar 13 22:59:00 2013 /sbin/route add -net 128.0.0.0 10.8.0.5 128.0.0.0 add net 128.0.0.0: gateway 10.8.0.5 Wed Mar 13 22:59:00 2013 /sbin/route add -net 10.8.0.0 10.8.0.5 255.255.255.0 add net 10.8.0.0: gateway 10.8.0.5 Wed Mar 13 22:59:00 2013 Initialization Sequence Completed Wed Mar 13 22:59:00 2013 write UDPv4: No route to host (code=65) Wed Mar 13 22:59:00 2013 write UDPv4: No route to host (code=65) Wed Mar 13 22:59:01 2013 write UDPv4: No route to host (code=65) Wed Mar 13 22:59:01 2013 write UDPv4: No route to host (code=65) Wed Mar 13 22:59:01 2013 write UDPv4: No route to host (code=65) Wed Mar 13 22:59:02 2013 write UDPv4: No route to host (code=65) Wed Mar 13 22:59:02 2013 write UDPv4: No route to host (code=65) Wed Mar 13 22:59:02 2013 write UDPv4: No route to host (code=65) Wed Mar 13 22:59:02 2013 write UDPv4: No route to host (code=65) Wed Mar 13 22:59:02 2013 write UDPv4: No route to host (code=65) ... The routing table after a connection WITHOUT the push redirect-gateway (all traffic is not redirected to the VPN and everything is working fine, I can ping or ssh the OpenVPN server and access all other Internet resources through my default gateway): Destination Gateway Flags Refs Use Netif Expire default user148-1.wireless UGSc 50 0 en1 10.8/24 10.8.0.5 UGSc 2 7 tun0 10.8.0.5 10.8.0.6 UH 3 2 tun0 127 localhost UCS 0 0 lo0 localhost localhost UH 6 6692 lo0 client.openvpn.net client.openvpn.net UH 3 18 lo0 142.1.148/22 link#5 UCS 2 0 en1 user148-1.wireless 0:90:b:27:10:71 UHLWIir 50 0 en1 76 user150-173.wirele localhost UHS 0 0 lo0 142.1.151.255 ff:ff:ff:ff:ff:ff UHLWbI 0 2 en1 169.254 link#5 UCS 1 0 en1 169.254.255.255 0:90:b:27:10:71 UHLSWi 0 0 en1 71 The routing table after a connection with the push redirect-gateway option enable as in the server.conf file above (all internet traffic should be redirected to the VPN tunnel, but nothing is working, I can't access any Internet ressources at all): Destination Gateway Flags Refs Use Netif Expire 0/1 10.8.0.5 UGSc 1 0 tun0 default user148-1.wireless UGSc 7 0 en1 10.8/24 10.8.0.5 UGSc 0 0 tun0 10.8.0.5 10.8.0.6 UHr 6 0 tun0 54.234.43.171/32 0.0.0.0 UGSc 1 0 en1 127 localhost UCS 0 0 lo0 localhost localhost UH 3 6698 lo0 client.openvpn.net client.openvpn.net UH 0 27 lo0 128.0/1 10.8.0.5 UGSc 2 0 tun0 142.1.148/22 link#5 UCS 1 0 en1 user148-1.wireless 0:90:b:27:10:71 UHLWIir 1 0 en1 833 user150-173.wirele localhost UHS 0 0 lo0 169.254 link#5 UCS 1 0 en1 169.254.255.255 0:90:b:27:10:71 UHLSW 0 0 en1

  Read the article

• Use GRUB/GRUB2 to PXE boot OS image

  - by Jack

  Asked this in stackoverflow but they recommended I post this here: Here is the situation I am in: I currently have a Windows drive that boots XP. The BIOS does not support PXE booting so this is out of the question. Therefore, I was thinking I could install a customized GRUB bootloader on it instead such that it will have the option to PXE boot an image from a DHCP server connected to it and have the option to load Windows as it normally does (two items in menu). The catch is it may need to be automated (meaning no keyboard), so is there any way to run a script pre-boot during GRUB loading that determines if DHCP / TFTP servers are running and attempt to PXE boot an image from the network (and if not, say timeout of 10 seconds, regularly boot from Windows drive)? If this is not possible, what are some other options / suggestions? I was reading up on grub4dos as well but I'm not sure that is what I need. FWIW, I'm free to do whatever I want to the drive. I'd really appreciate some help on this as I'm not sure where to start. Thanks!

  Read the article

• Securing NTP: which method to use?

  - by Harry

  Can someone good at NTP configuration please share which method is the best/easiest to implement a secure, tamper-proof version of NTP? Here are some difficulties... I don't have the luxury of having my own stratum 0 time source, so must rely on external time servers. Should I read up on the AutoKey method or should I try to go the MD5 route? Based on what I know about symmetric cryptography, it seems that the MD5 method relies on a pre-agreed set of keys (symmetric cryptography) between the client and the server, and, so, is prone to man-in-the-middle attack. AutoKey, on the other hand, does not appear to work behind a NAT or a masquerading host. Is this still true, by the way? (This reference link is dated 2004, so I'm not sure what is the state of art today.) 4.1 Are public AutoKey-talking time servers available? I browsed through the NTP book by David Mills. The book looks excellent in a way (coming from the NTP creator after all), but the information therein is also overwhelming. I just need to first configure a secure version of NTP and then may be later worry about its architectural and engineering underpinnings. Can someone please wade me through these drowning NTP waters? Don't necessarily need a working config from you, just info on which NTP mode/config to try and may be also a public time server that supports that mode/config. Many thanks, /HS

  Read the article

• Restoring a fresh home folder in a shared user domain environment

  - by Cocoabean

  I am using a tool called pGINA that adds another credential provider to my Windows 7 clients so we can authenticate campus users via campus LDAP. We have the default Windows credential providers setup to authenticate off of our Active Directory, but we have students in our classes that don't have entries in our AD, and we need to know who they are to allow them internet access. Once these LDAP users login using pGINA, they are all redirected to the same AD account, a 'kiosk' account with GPOs in place to prevent anything malicious. My concern is that my users will accidentally save personal login information or files in that shared profile, and another user may login later and have access to a previous user's Gmail account, as the AppData folder on each computer is shared by anyone logging into the kiosk user. I've looked into MS's 'roll-your-own' SteadyState but it didn't seem to have what I wanted. I tried to write a PS script to copy a pre-saved clean version of the profile from a network share, but I just kept running into issues with CredSSP delegation and accessing the share from the UNC path. Others have recommended something like DeepFreeze but I'd like to do it without 3rd party tools if possible.

  Read the article

• Single Sign On 802.1x Wireless - saying “Connecting to <SSID>”, hangs for 10 seconds, fails with “Unable to connect to <SSID>, Logging on…”.

  - by Phaedrus

  We are implementing WiFi on Windows 7 machines in our corporate environment. Machines should be able to log into the domain by WiFi as the Machine (Pre-Logon), and as the User (Post-Logon). We have everything working correctly except for 2 things: 1) Sometimes the login scripts don't run 2) The user VLAN is sometimes different than the machine vlan, and no DHCP renew occurs after user logon. I am clear that both these problems should be fixable by using the "Single Sign On" Option under the 802.1x Wireless Vista GPO, and setting the wireless to connect immediately before user logon and also by enabling "This network uses different VLAN for authentication with machine and user credentials" If I enable these GPO settings in a lab, the computer does authenticate & gets WIFI before the user logs on, so when the login box is displayed, it says “Windows will try to connect to ”, even though it is already connected (which should be ok?). Enter the user credentials and it goes to a screen saying “Connecting to ”, hangs for 10 seconds, fails with “Unable to connect to , Logging on…”. Desktop fires up and then the user re-authenticates with no problem as himself instead of the machine, but by that point, we defeat the point of the WiFi SSO “before user logon”. Also by that point, no DHCP renew seems to occur, and the user is still stuck with the wrong IP address for the new VLAN. When the “Connecting to ” screen comes up, there’s no indication on the AP or the Radius server that anything whatsoever is happening after credentials are entered until after the domain logon. Also with this policy enabled, sometimes windows hangs on a black screen indefinitely until I disable the Wireless NIC, so something is knackered for sure. What have I missed? Suggestions are much appreciated... /P

  Read the article

• What kind of server configuration is best for a chatting app? [closed]

  - by mohabitar

  I'm just now starting to go deeper into the world of cloud hosting and databases, and am getting overwhelmed by how deep this information goes. It's all a little too much to consume in a short amount of time. I get a lot of pricing information, but I'm unable to determine what that means to me. I'm making what you might compare to an email app. Users can send messages to one another. I just don't understand, out of the several options, what would be ideal for an app like this, where users would be constantly sending and receiving text data. With Amazon DynamoDB, I have to specify a pre-defined throughput with number of reads and writes per second. Sure I can just type 50, but I'm not exactly sure what 50 writes per second represents. I'm trying to determine what would be the most cost efficient solution, and I want to know what a throughput of 50 reads/writes/second compares to. Is that a high number? What is a good throughput number for a message sending app with say 50,000 daily users? I'm just providing specific numbers so I can understand what these throughput numbers represent. 100 transactions/second to me seems like a small number since I'm not familiar with this stuff, so I'm just looking to bring everything in context. What would 100 read/write/second be useful for? Are there any average example values available? And I'm not sure what each service is good for. For a message sending app, is there any reason I'd want to choose say Amazon DynamoDB over Google App Engine? Any insight would be greatly appreciated.

  Read the article

• Unnamed, hidden partitions on my 500 GB HD, HP Pavilion dm4 Laptop

  - by emotionull

  I have multiple doubts here. Its a Seagate 500GB 7200RPM HD. I had installed it few months back after my original Laptop HD stopped working. The current drives on my latop, as shown by the Windows Disk Management are: After installing the new HD, I had done a complete clean install of Windows 7 and I didn't create any parition myself, manually. So there are 4 drives. Even previously, before I installed this new HD, my laptop had 4 Partitions. But the there were no un-named partitions like the two in this case. The other two were HP tools and Recovery or something. It was pre-configured, Factory installed Windows. Also, now when I right cick on the unnamed Drives from Disk Management, all the options are greyed out (see image) except the delete partition image. So how do I know what's inside those partitions? Will it be ok if I delete them? I want install Ubuntu and dual boot it with my current windows installation. I cannot do it in current setup as there are already 4 partitions of my HD and if I will try to make a new partition, it will be a logical one (correct me if I am wrong here). So can I delete the un-named, hidden partitions and use them for Ubuntu? A bit unrelated question. As a backup option, can I use the Windows 7's Backup and Restore facility to keep a complete backup of all the drivers and system softwares.

  Read the article

• Laptop Synaptics Touchpad No Longer Functional After Windows 7 Upgrade

  - by Chance

  I have a Toshiba laptop, with an integral Synaptics (PS/2 port) touch pad, that I bought pre-installed with 32-bit Windows Vista. After doing a clean install of 32-bit Windows 7, I can no longer get the touch pad to respond. The function (FN) keys on the laptop still operate correctly, but they no longer display on screen when used. I have no way of knowing if the function key to enable / disable the touch pad is working correctly, although the function keys for dim / brighten display, as well as others, work fine. I have removed the device from the device manager and allowed it to reinstall with no success. I have removed the previous drivers and updated them with the current 32-bit Win7 compatible versions from Synaptics website, with no success. The Synaptics icon displays in the taskbar, and the touch pad is available in the Device Manager, both of which say the device is installed and working correctly. I have checked to make sure that the touch pad is enabled in the Synaptics menu, and have tried toggling enabled / disabled with no success. If anyone has any suggestions, or knows where I can find a solution, I would be very appreciative.

  Read the article

• Puppet: is it ok to "force" certname when you expect to shuffle nodes around?

  - by Luke404

  We all know (good example on SF) that Puppet hostname detection could be... fun. At our company (and I guess we're not alone at this) we usually pre-configure servers at our offices and test them before bringing the gear to a remote datacenter and rack them. Of course the reverse dns will change when doing that, even if we don't change the actual hostname of the system. We're slowly drafting our puppet setup and I'd like to be sure those moves won't create problems. My idea is to explicitly configure the desired full FQDN of the system as certname in puppet.conf at server provision time (before the very first puppet run). My process would look something like this: basic o.s. installation basic network configuration, enough to reach the internet and resolve dns install puppet and set up certname start puppet and let him manage the whole configuration test, fix problems in config (via puppet), re-test, and so on... manually stop puppet set up new network configuration for the datacenter network move the machine to DC turn it on puppet should automatically start and keep on doing its job The process is supported by detecting the environment in puppet's manifests (eg. based on subnet, like they do at Wikimedia) and modify configuration as needed (eg. resolv.conf contents appropriate for each network). Each node's certname will never change for the whole system life cycle. Is there any problem with this approach? Could it be improved?

  Read the article

• What are the possible problems, when wget returns code 500 but same request works in normal browsers?

  - by markus

  What should I be looking for, when wget returns 500 but the same URL works fine in my web browser? I don't see any access_log entries that seem to be related to the error. DEBUG output created by Wget 1.14 on linux-gnu. <SSL negotiation info stripped out> ---request begin--- GET /survey/de/tools/clear-caches/password/<some-token> HTTP/1.1 User-Agent: Wget/1.14 (linux-gnu) Accept: */* Host: testing.thesurveylab.net Connection: Keep-Alive ---request end--- HTTP request sent, awaiting response... ---response begin--- HTTP/1.0 500 Internal Server Error Date: Wed, 12 Dec 2012 14:53:07 GMT Server: Apache/2.2.3 (CentOS) Set-Cookie: blueprint2-staging=8jnbmkqapl30hjkgo0u6956pd1; path=/ Expires: Thu, 19 Nov 1981 08:52:00 GMT Cache-Control: no-store, no-cache, must-revalidate, post-check=0, pre-check=0 Pragma: no-cache Strict-Transport-Security: max-age=8640000;includeSubdomains X-UA-Compatible: IE=Edge,chrome=1 Content-Length: 5 Connection: close Content-Type: text/html; charset=UTF-8 ---response end--- 500 Internal Server Error Stored cookie testing.thesurveylab.net -1 (ANY) / <session> <insecure> [expiry none] blueprint2-staging 8jnbmkqapl30hjkgo0u6956pd1 Closed 3/SSL 0x0000000001f33430 2012-12-12 15:53:07 ERROR 500: Internal Server Error.

  Read the article

• How to fix Truecrypt MBR using Command Prompt or Linux live USB?

  - by Michal Stefanow

  I was playing with TrueCrypt and decided to make a fresh installation of Windows 7 from USB stick. Unfortunately Windows 7 installer: "setup was unable to create a new system partition" My entire HDD has been formatted and is visible as 320GB unallocated space, but no fdisk nor Windows 7 installer nor Windows XP installer could help. (Windows XP doesn't even see the HDD, it sees only USB stick and says "not enough space to install") It may be related to Truecrypt and pre-boot authentification, boot loader and/or MBR. As I don't have optical device I could not have created rescue disk. Right now I need a rescue of some kind, supposingly by erasing/fixing MBR using Linux live USB or using Command Promt. Another approach is to click "repair your comuter" menu from Windows 7 installer then click "restore your computer", then click OK upon error and get access to Command Prompt. Yet another another approach is to start computer without Linux USB I receive this: error:unknown filesystem. grub rescue> Any help would be greatly appreciated as my laptop is kind of not fully operational now. UPDATE: This was asked long time ago, ended up formatting everything (eventually it worked using different bootable USB)...

  Read the article

• Remote Desktop Services Licensing - Does server have to have a RDS role?

  - by transistor1

  I recently set up a "micro" size Windows 2008 Datacenter server on Amazon AWS. My small group needs several concurrent RDS users to be able to access the machine. Without installing the "Remote Desktop Server" role, it allows 2 concurrent connections. I read on MS' website that in order to set up multiple users, we needed to install the RDS role. I did so, but now the application we are trying to share is running much slower than it was before. Prior to the role installation, it was taking about 5 seconds to open; now it is taking a few minutes to open -- without any other users logged on except me. My assumption is that the RDS role may be too much for this micro instance to handle, and currently, changing to another size instance is not an option (it may be possible later if we were to receive enough funding). This leads me to the following questions: 1) Is it a sensible assessment to assume that it is the RDS role is slowing things down, or are there other things that I could look at to speed it up? We are talking about a machine with ~600MB of memory. 2) If I revert back to the pre-RDS role, is there any legitimate way (in terms of purchasing RDS licenses) to get more than 2 concurrent desktops? I did read this, and am not questioning that the answerer is knowlegeable; but someone else may have some other experience. I am also making it clear that we want to do this in a legitimate way. Thanks in advance for any assistance that can be provided! EDIT: if it is helpful in answering the question, the application in question is a Lotus Approach database. Also, I am asking this from a technical perspective: not a legal one. I want to know if it is possible to install valid licenses without the RDS role.

  Read the article

• HSphere - Only sees Apache 2 Test Page after forced shutdown?

  - by Darkwoof

  Hi, I have a dedicated server running on a Dell PowerEdge 850 with CentOS 4.4 and HSphere 3.0 Patch 6 colocated at a datacenter. Last night my hosting company had to schedule a change in the power bar, and I gave the go ahead for them to shut down the server and bring it up when they are done. Since they do not have admin access to the machine, I suppose they did a forced shutdown. When the machine was brought up, I found that all my domains (and sub-domains) are now pointing to an "Apache 2 Test Page" instead of the pre-configured sites that were running prior to the shutdown. This apparently only affects the standard sites running on port 80 - my Webmin instance running at port 1000 is still accessible for example, as well as my HSphere control panel running at port 8080. I've checked the config settings using the HSphere UI for each of the sites, and didn't find anything wrong. I've also tried rebooting the server via SSH, which does not rectify the problem. I've previously done reboots with no issues; the sites would just come right back up when its done, but not this time. I'm guessing some configuration file got corrupted or overwritten this time? Anyone with experience with HSphere and can provide some advice on what's happened and how to solve it? Thanks. (I do not have an active support agreeement for HSphere since Parallels took over and increased the min. license to 200. I only had 25 license for use by family and friends.) Thanks in advance.

  Read the article

• Migrating ODBC information through a batch file

  - by DeskSide

  I am a desktop support technician currently working on a large scale migration project across multiple sites. I am looking at a way to transfer ODBC entries from Windows XP to Windows 7. If anyone knows of a program or anything prebuilt that already does this, please redirect me. I've already looked but haven't found anything, so I'm trying to build my own. I know enough basic programming to read the work of others and monkey around with something that already exists, but not much else. I have come across a custom batch file written at one site that (among other things) exports ODBC information from the old computer and stores it on a server (labelled as y: through net use at the beginning of the file), then later transfers it from the server to a new computer. The pre-existing code is for Windows XP to XP migrations. Here are the pertinate bits of code: echo Exporting ODBC Information start /wait regedit.exe /e "y:\%username%\odbc.reg" HKEY_LOCAL_MACHINE\SOFTWARE\ODBC\ODBC.INI (and later on) echo Importing ODBC start /wait regedit /s "y:\%username%\odbc.reg" We are now migrating from Windows XP to 7, and this part of the batch file still seems to work for this particular site, where Oracle 8i and 10g are used. I'm looking to use my cut down version of this code at multiple sites, and I'm wondering if the same lines of code will still work for anything other than Oracle. Also, my research on this issue has shown that there are different locations in 64 bit operating systems for 32/64 bit entries, and I'm wondering what effect that would have on the code. Could I copy the same data to both parts of the registry, in hopes of catching everything? Any assistance would be appreciated. Thank you for your time.

  Read the article

• ASA 5505 VPN setup. VPN works but still unable to reach devices in the inside network.

  - by chickenloop

  I've setup a Remote Access VPN on my Cisco ASA 5505. I'm able to connect to my ASA via my phone or the Cisco client, but I'm unable to reach devices in my inside LAN when connected via VPN. The setup is the following: Inside Network : 10.0.0.0/24 VPN_POOL: 172.16.0.0/24 Outside Network: 192.168.1.0/24 ASA is not the perimeter router, there is another device on the 192.168.1.0/24 network which is connected to my cable provider. Obviously UDP port 500 and 4500 are forwarded to the ASA's outside interface. Everything works perfectly, besides the VPN stuff. Config: interface Vlan1 nameif inside security-level 100 ip address 10.0.0.254 255.255.255.0 interface Vlan2 description Outside Interface nameif outside security-level 0 address 192.168.1.254 255.255.255.0 object network VPNPOOL subnet 172.16.0.0 255.255.255.0 object network INSIDE_LAN subnet 10.0.0.0 255.255.255.0 Then the exempt NAT rule. nat (inside,outside) source static INSIDE_LAN INSIDE_LAN destination static VPNPOOL VPNPOOL I don't think that the problem is with the VPN config, as I can successfully establish the VPN connection, but just in case I post it here: group-policy ZSOCA_ASA internal group-policy ZSOCA_ASA attributes vpn-tunnel-protocol ikev1 split-tunnel-policy tunnelspecified split-tunnel-network-list value Split-Tunnel default-domain value default.domain.invalid tunnel-group ZSOCA_ASA type remote-access tunnel-group ZSOCA_ASA general-attributes address-pool VPNPOOL default-group-policy ZSOCA_ASA tunnel-group ZSOCA_ASA ipsec-attributes ikev1 pre-shared-key ***** Any ideas are welcome. Regards.

  Read the article

< Previous Page | 240 241 242 243 244 245 246 247 248 249 250 251  | Next Page >