Search Results

Search found 8224 results on 329 pages for 'sometimes'.

Page 244/329 | < Previous Page | 240 241 242 243 244 245 246 247 248 249 250 251  | Next Page >

  • router only assigns small number of IPs

    - by Liam Coates
    Been having a problem with my router for a while now, might just be because it is really old but here's the problem: If a lot of computers are connected to my home network someone will get disconnected. They are assigned IPs and it seems like at a certain point (and I don't know how many) you either get assigned the same IP as someone else or something else is happening and you get disconnected - until i soft reset it and it works again which takes 30 secs. I'd say my tablet, my PC, my sisters iPad, 2 laptops and a netbook is the most that can be connected at one time so that is 6 but that should be fine. The only way I know this is the problem is because I turned on my tablet and I was online on my PC, got disconnected but my tablet was still connected, this is just after i turned the tablet on so I know my router is having difficulty with IPs, it is like it assigned the same IP to the tablet which then clashed with my desktop and knocked me off. I see that sometimes the following solves it as well so I wrote a batch file with a menu to execute these commands as I have to do it so often. ipconfig /release ipconfig /flushdns ipconfig /renew Any ideas? Or shall I just get a new router as this one is old and maybe can't handle giving out that many IPs? Cheers!

    Read the article

  • Hardware issue: computer plays beep sounds at startup, and then turns off

    - by Darkkurama
    Turns out that after moving, my computer got damaged somehow. I installed my computer 2 days ago. I didn't check the state of the hardware parts and turned the pc on recklessly, not realizing that the cpu fan was dettached from the cpu. After this I reattached the fan. The computer worked kind of faulty after that, because at the time of startup, it would play a long beep (different from the normal beep) and won't display anything. I tried restarting after this incident and it got fixed (don't know how, but it did), and I was even able to play some videogames for some hours (more than 5). This morning I tried to get this issue sorted out by checking again the cpu and in general, the connections, and for my surprise, at the time of turning it on again, the computer wouldn't boot at all. I reapplied some thermal paste to the cpu and fan, but got no results (I did this because the old paste was very badly distributted along the surface of both cpu and fan). Now every time I turn it on, the computer acts randomly: sometimes at startup, it plays a long continous beep and then turns off. one time it played a long continous beep and got to the windows password input screen, but then it turned off More frequently, I turn it on and after some seconds, it turns off without any sound. You can check this video I recorded, which features how the computer behaves most of the time Another one I tried troubleshoting it myself by disconnecting my graphic card, rams, HDD and even the cpu and its fan with no result. Computer specs: Intel Core 2 Quad Q6600 processor, Nvidia xfx gtx 260 black edition, 4 GB ram, 500 GB hard drive, Windows 7 64 bit

    Read the article

  • Dual Monitor setup issues between laptop and external led monitor

    - by Julian
    I have two challenges. Monitor will not connect to laptop through HDMI Watching HD video content causes the laptop to sometimes turn off expecially when I'm streaming from tekzilla.com Setup. I got my new HP 2311x LED LCD monitor this week and I have it running as the main monitor extended by the 15 inch screen on my Dell Studio 1558. Right now I have to connect the external monitor through VGA. For the HDMI connection issue. I suspect that either the appropriate drivers are not installed because I don't see any hdmi device in the device manager. I've checked and I don't see any hdmi specific drivers listed online. For the shut down issue, I suspect the laptop might be overheating. Not sure why it would. It never did that while I watched movies on my laptop's default screen. My Laptop Configuration: 15" led lcd screen at 1366 x 768 intel i5 processor integrated graphics card 4 GB DDR3 RAM 500 GB hard drive I've tried everything from switching the source on my monitor to hdmi to start up combinations and nothing has worked. What could be the issue and how do I solve it?

    Read the article

  • I am looking for a tool to measure or detect "unresponsiveness" of a desktop PC

    - by Tom H
    I have a client that provides some server systems to a hospital, and a support ticket was raised that the desktop application was hanging waiting for the server. We did some extensive testing and its pretty clear that the server is responsive, and the network is fine, and that the problem is on the client end. (no requests are received during the hang etc...) We take a look at the desktop machines and they should be fine, so we raise tickets with the software vendor who says that it must be the hardware, the hardware company says that it is the software, etc etc Anyway, so talking to the nurses, they say that these machines often "hang" for 30 seconds at a time, and sometimes during important moments where they need to get data for a patient who is unwell, such as charts and status. So I want to stick a client on these machines that would be able to detect arbitrary "unresponsiveness" of the keyboard/mouse and log that for analysis later. Obviously I am wary to suggest some application that takes resources and makes the problem even worse, so I would interested to see any tools that would detect these (is it correct to say that the keyboard interrupts are being discarded?) scenarios by looking for the OS discarding the interrupts, or whatever is appropriate here. so go on then serverfault, here is your chance to save a life.... ;-) Edit: I am starting to think that some of the tools associated with real time systems might be appropriate, at least as a diagnostic.

    Read the article

  • Why does Windows make random "device connect" and "device disconnect" sounds?

    - by Steve Elmer
    Hello, I've been noticing this since Windows Vista. I see it on Windows 7, now, as well. In any case throughout the day I notice that my computer makes apparently random device-connect and/or device-disconnect ("boink") sounds. I suppose it is the same sound you hear when connecting or disconnecting a USB device such as a thumb drive. I've noticed that this happens on each of three computers I work with at home, my wife's computer, and my machine at work. It happens without any user action at all - i.e. I'll be just sitting there (hands off my mouse and keyboard), and the computer will make the sound. There is no visual queue or anything. Just the sound. I have sometimes gone in pursuit of the sound - running virus scans, examining event logs and such, and observing task manager - but have never had any luck tracking this thing down, but have not had any luck. Surely someone else out there must be experiencing this, too. Any ideas? Thanks, Steve

    Read the article

  • Why does Windows make random "device connect" and "device disconnect" sounds?

    - by Steve Elmer
    Hello, I've been noticing this since Windows Vista. I see it on Windows 7, now, as well. In any case throughout the day I notice that my computer makes apparently random device-connect and/or device-disconnect ("boink") sounds. I suppose it is the same sound you hear when connecting or disconnecting a USB device such as a thumb drive. I've noticed that this happens on each of three computers I work with at home, my wife's computer, and my machine at work. It happens without any user action at all - i.e. I'll be just sitting there (hands off my mouse and keyboard), and the computer will make the sound. There is no visual queue or anything. Just the sound. I have sometimes gone in pursuit of the sound - running virus scans, examining event logs and such, and observing task manager - but have never had any luck tracking this thing down, but have not had any luck. Surely someone else out there must be experiencing this, too. Any ideas? Thanks, Steve

    Read the article

  • management network to a network port for additional ones munin and monit

    - by paolo
    management network to a network port for additional ones munin and monit I want to build a separate Netzwek for server management. I have several network cards a linux / debian / ubuntu with computer. Set both network cards sin in the /etc/network/interfaces. # The primary network interface #allow-hotplug eth0 #iface eth0 inet dhcp auto eth0 iface eth0 inet static address 10.0.0.240 netmast 255.255.255.0 network 10.0.0.0 brodacast 10.0.0.255 gateway 10.0.0.254 auto eth1 iface eth1 inet static address 10.0.10.240 netmast 255.255.255.0 network 10.0.10.0 brodacast 10.0.10.255 post-up ip route add 10.0.0.0/24 dev eth0 src 10.0.0.240 table eth0-WAN post-up ip route add default via 10.0.0.254 table eth0-WAN post-up ip route add 10.0.10.0/24 dev eth1 src 10.0.10.240 table eth1-LAN post-up ip route add default via 10.0.10.200 table eth1-LAN post-up ip rule add from 10.0.0.240 table eth0-WAN post-up ip rule add from 10.0.10.240 table eth1-LAN still i adjusted / etc/iproute2/rt_tables and following routes set up in the /etc/network/interfaces I want to have both applications and the network interface separately as munin and monit only on eth1 and not have to eth0. it goes to the reboot but sometimes not always. # Traceroute-i eth1 10.0.10.200 not go what am I doing wrong?

    Read the article

  • Google Chrome warning that Javascript is disabled

    - by kirchoffs415
    I hope somebody can help. I keep getting the following message when I log on: Your Javascript is disabled. Limited functionality is available. It will stay for maybe a day sometimes two. I have uninstalled javascript and reinstalled but still the same. I am using chrome. Any help would be grateful many thanks Dominic My system spec is as follows System InformationOS Name Microsoft® Windows Vista™ Home Premium Version 6.0.6002 Service Pack 2 Build 6002 Other OS Description Not Available OS Manufacturer Microsoft Corporation System Name DOM-PC System Manufacturer Dell Inc. System Model Inspiron 1545 System Type X86-based PC Processor Pentium(R) Dual-Core CPU T4200 @ 2.00GHz, 2000 Mhz, 2 Core(s), 2 Logical Processor(s) BIOS Version/Date Dell Inc. A05, 25/02/2009 SMBIOS Version 2.4 Windows Directory C:\Windows System Directory C:\Windows\system32 Boot Device \Device\HarddiskVolume3 Locale United Kingdom Hardware Abstraction Layer Version = "6.0.6002.18005" User Name DOM-PC\DOM Time Zone GMT Standard Time Installed Physical Memory (RAM) 3.00 GB Total Physical Memory 2.96 GB Available Physical Memory 1.38 GB Total Virtual Memory 5.89 GB Available Virtual Memory 4.25 GB Page File Space 3.00 GB Page File C:\pagefile.sys My System Specs

    Read the article

  • Why Does DreamWeaver CS5 Discriminate between File Extensions, Even After Modding Mime Types!?

    - by Sam
    Hi folks, Even After I forced DreamWeaver CS5 to allow opening of .ast extensions as a MIME type of php5, which DreamWeaver now opens and colors correctly as described here, I still have trouble figuring out why it still discriminates between the two file extensions! Symptoms: External Files & Design View I have a file foo.php which php includes other files (e.g. the php-combined css.php and js.php). Now, when opening foo.php all functions work perfectly: the external (included) php files are all recognised correctly. However, when I change foo.php foo.ast, and open it again, It does not recognise the files extensions anymore in the top bar. Also, I lose the Design / Live View functionality.** When I change foo.ast to foo.php, all works again! Anyone any clues of why there remains a a difference between one and other extension? Note1: I have added the .ast extension to these four files, next to .php: 1 C:\Users\Sam\AppData\Local\VirtualStore\Program Files (x86)\Adobe\Adobe Dreamweaver CS5\configuration\DocumentTypes\MMDocumentTypes.xml 2 C:\Program Files (x86)\Adobe\Adobe Dreamweaver CS5\configuration\DocumentTypes\MMDocumentTypes.xml 3 C:\Users\Sam\AppData\Roaming\Adobe\Dreamweaver CS5\en_US\Configuration\Extensions.txt 4 C:\Program Files (x86)\Adobe\Adobe Dreamweaver CS5\configuration\Extensions.txt Note2: sometimes, even .php files do not want to show in design view or live view. Could this be caused by a corrupted installation?

    Read the article

  • What's next for all of these Microsoft "overlapping" and "enhanced" products ?

    - by indyvoyage
    Recently I attended a road show, organised by MS Gold Partner company in the UK. The products discussed were: SharePoint server (2010 and 2007), Exchange server, Office Communication Server 2007, Exchange hosted services Office Live meeting, Office Communicator, System Center Configuration Manager and Operation Manager, VMware, Windows 7 etc. As Microsoft claims the enhancement in the each product against higher version, I felt that clients are not much interested in all these details. For example Office Communicator, surely they have improved a lot the product and first site all said 'WOW' great product, but nobody wish to pay money for all these extra features. Some argued, they are bogged down by all these increased number of menus. They don't need soft call feature included with mobile call. It apply for all other products as well such as MS office (next what 2 ribbons ?), windows OS and many more. Indeed there must be good features in all these products, but is it worth to spend money and time to update the older system ? Also sometimes these feature will decrease the productivity instead increase it. *So do you think what ever enhancement MS is doing in the products is only for selling purpose, not a real use ?? and I think also keep the developer busy learning the new tools and features. * I am sure some some people here will argue that some people need this sort of features. But I am not talking about NASA or MI5 guys. I am talking of usual businesses and joe public. Any ideas welcome.

    Read the article

  • Can any postfix guru assist me determine how emails are still being sent via my server from unauthorized sources?

    - by Dave
    Hi all, I'm getting a little concerned as I run a small server hosting a number of websites and manage the email for a few dozen people. Just recently though I've had a couple of notifications from spamcop alerting me that spam has been sent from my server, and when I have a look over the logs from time to time I can indeed see that there are many repeated attempts of mail being sent from my server. Most of the time it gets knocked back from the destination servers but sometimes its getting through. Unfortunately I'm not linux or postfix expert, I can get by but had though I had my machine locked down quite securely, I don't allow relaying, when I check the online DNS/MX tools they tend to report my server as being OK so I'm not sure where to take it now and hoping someone might be able to throw me a few pointers. I get lots of entries like this in my MAIL.INFO log Jan 2 08:39:34 Debian-50-lenny-64-LAMP postfix/qmgr[15993]: 66B88257C12F: from=<>, size=3116, nrcpt=1 (queue active) Jan 2 08:39:34 Debian-50-lenny-64-LAMP postfix/qmgr[15993]: 614C2257C1BC: from=<[email protected]>, size=2490, nrcpt=3 (queue active) and Jan 7 16:09:37 Debian-50-lenny-64-LAMP postfix/error[6471]: 0A316257C204: to=<[email protected]>, relay=none, delay=384387, delays=384384/3/0/0.01, dsn=4.0.0, status=deferred (delivery temporarily suspended: host mx.fakemx.net[46.4.35.23] refused to talk to me: 421 mx.fakemx.net Service Unavailable) Jan 7 16:09:37 Debian-50-lenny-64-LAMP postfix/error[6470]: 5848C257C20D: to=<[email protected]>, relay=none, delay=384373, delays=384370/3/0/0.01, dsn=4.0.0, status=deferred (delivery temporarily suspended: host mx.fakemx.net[46.4.35.23] refused to talk to me: 421 mx.fakemx.net Service Unavailable) then there tends to be connection timeouts, so from what I see even though I had relaying disabled.. something is getting by and trying to send.. So if you can help that will be greatly appreciated, and any further logging/config info I can supply. Thanks

    Read the article

  • Jenkins CI - Cannot allocate memory

    - by Programmieraffe
    I tested jenkins-ci successfully on a ubuntu 10.4 (with vmware fusion) on my local computer. Now I want to install and use it on my virtual server at hosteurope. The basic installation was no problem, but now I have problems with my build project. After pulling an mercurial update from a repository, ant is invoked and throws the following error in my build project: "Buildfile: /var/lib/jenkins/workspace/concrete5-seed-clean/build.xml [property] java.io.IOException: Cannot run program "/usr/bin/env": java.io.IOException: error=12, Cannot allocate memory" There is a known problem with heap size at virtual servers at hosteurope (http://faq.hosteurope.de/index.php?cpid=13918), so I tried to set the heap size manually: # for ant export ANT_OPTS="-Xms512m -Xmx512m" # jenkins # edited /etc/default/jenkins, added line JAVA_ARGS="-Xms512m -Xmx512m" # restarted jenkins via /etc/init.d/jenkins restart After setting this for ant, the command "ant -diagnostics" runs through and does not cause an error, but the error still occurs when I try to build the project. Server-Details: - http://www.hosteurope.de/produkt/Virtual-Server-Linux-L Ubuntu 10.4 LTS RAM: 1GB / Dynamic 2GB My questions: - Is 1GB enough for Jenkins or do I have to upgrade the server? - Is this error caused by ant or jenkins? Update: I got it running with ant options -Xmx128m -Xms128m, but sometimes the error occurs again. (this freaks me out, cause i can not reproduce it by now :/ ) Help much appreciated! Cheers, Matthias

    Read the article

  • Weird PCI bug: lots of missed packets, or data comes in "bursts"

    - by Thomas O
    I have an ABIT KN9 motherboard. It has one PCI-e x16 slot, three PCI-e x4 slots and two legacy PCI. My problem is with the legacy PCI (which I shall just call "PCI".) I currently have an Nvidia GeForce 8600 GT (a low end card) installed in the x16 slot and a TV card in PCI #1; the x4 slots are unused, as is PCI #2. I plan to upgrade the graphics card soon, the current card was spare. I sometimes install a USB expander in PCI #2 but it causes a lot of problems - see below. The problem is under Linux (Ubuntu 10.10, Linux 2.6.35-22-generic), but probably under all operating systems (I have not yet been able to test Windows, but I suspect it will do the same as the problems occur on the BIOS/POST side too, e.g. when using a USB keyboard on the expander the keyboard will not work at all) PCI has an enourmous delay, and packets arrive in large chunks. For example, when using the USB expander, my USB mouse lags and jumps in large steps every second or so, while using the motherboard USB does not present this problem. My TV card will only do one or two frames per second, and the program (xawtv) usually times out and crashes. In dmesg, I'm getting messages like: bttv0: timeout: drop=74, irq=154/100476, risc=31f6256c, bits: VSYNC HSYNC OFLOW RISCI for my TV card, and similar timeout issues for my USB expander with a mouse. I received the motherboard, processor and RAM second hand and have only just got around to building it, so I don't know if this problem has always existed, or if it's a result of my set up. If anyone has any hints or solutions it would be appreciated - this is kind of a show-stopper for me.

    Read the article

  • Outlook won't re-connect to exchange after network is re-connected

    - by stan503
    I have a setup at my desk where I connect my computer to a an RJ45 switch that switches between two networks. One network is the corporate network, which is maintained by my company's IT, and the other is my own private network where I do testing (the two networks have to be separated). The corporate network hosts the exchange server where I get e-mail. When I switch from the private network to the corporate network, I expect Outlook to re-connect to the exchange server. However, I have found that sometimes when I come back, Outlook take an extremely long time to re-connect. Send/Receive will give me back the error 'The server is not available' (0x8004011D). It will sit there for 10 minutes to a few hours before it finally re-connects. The only other option is to reboot my computer, which is a huge pain for me since I run multiple VMs on it. This usually happens when I'm connected to the private network for a significant amount of time, so I'm thinking it's because Outlook has cached the network status. Is there a way to force Outlook to do a 'hard' re-connect to the exchange server? I'm using Windows XP SP 3 with Outlook 2007.

    Read the article

  • Thumbnail generation with imagemagick doesn't render the correct colors

    - by Bastien
    Generating thumbnails of PDFs with imagemagick sometimes renders incorrect colors. We're using an old version of imagemagick (6.5.7-8, that's the version installed on the heroku servers). Here is the command we're currently using: convert -size "725x1200>" -colorspace RGB -flatten -density 300 -quality 100 input.pdf output.jpg I've tried using different colorspaces like sRGB,YIQ,.. but none of them are rendering the color correctly. Using imagemagick-6.7.7-6 locally works so I've tried to bundle the 'convert' command within my application /bin directory, the command works but the result is still wrong, so it seems that the problem comes either from another imagemagick command used by 'convert' or from another library. Here's an example of the outputs: Correct output: http://i.stack.imgur.com/gf9eG.jpg Wrong output: http://i.stack.imgur.com/imUeD.jpg Strangely, with some pages of the same pdf the output is always correct. Any idea which library or command could be the issue, or if there is a proper set of options to pass to imagemagick to always get it right? Thanks in advance for your help.

    Read the article

  • Network Load Balancing, intermittent port problem on Windows Server 2008

    - by Jimmy Chandra
    Trying to troubleshoot an intermittent problem on a Windows Server 2008 NLB. I think it might be related to an NLB issue. We are using Windows Network Load Balancing to balance load for our multiserver SharePoint front ends. Say... Web Front End 1 IP is 192.168.1.100 and Web Front End 2 IP is 192.168.1.101, the NLB is setup to load balance both WFE servers on any incoming traffic to the IP 192.168.1.200. Sometimes we got an intermittent issue where when we try to access the SharePoint site using 192.168.1.200:8080 (say the site is set up to run on port 8080) from a remote client, it will display page not found. Pinging the 192.168.1.200 will give responses, but when trying to telnet to 192.168.1.200:8080 it just won't connect. However, browsing the SharePoint site directly on individual WFE (192.168.1.100 and 192.168.1.101) show no problem whatsoever. My guess also (we didn't get a chance to try it yet, but I think it should work), if I try connecting remotely to individual server, it will respond just fine. But any attempt on trying to connect using the virtual IP (192.168.1.200) will fail miserably. Funny thing is, after a while it will return back to normal. Anyone had similar experience with this type of problem while implementing NLB before? We are doing this in a virtual environment.

    Read the article

  • How/when do you study?

    - by Sergei
    Would be interesting to find out how other sysadmins are educating themselves. I find myself in the need of constantly learning new things. I prefer to spend more time on the subject and know it thoroughly knowing that not doing so will kick me back in the future. This can be frustrating sometimes as it feels that I move too slowly. Our company has account on safari.oreilly.com and I am reading a book or two at any given time. I also read sysadmin related blogs for ideas and tips and to keep myself in the tune with the trends. I cannot do any study at home as I would rather spend my out of work hours with my family plus I find it hard/impossible to study at home due to the inability to concentrate at home. So I mostly study while on the train, luckily my commute time takes up to 2 hours a day. I also read a lot at work and don't feel guilty about it. To fix/implement/plan, I need to have a solid knowledge and if it requires time then this is a part of my job being a sysadmin. There is a joke that says "sysadmin is a person that knows a lot about everytihng and as a result knows nothing" - I think ther is a grain of truth here...

    Read the article

  • What can I do to prevent system power downs?

    - by Joe King
    Yesterday I was given my brother's old laptop - core i7, 2.67GHz, 8GB RAM, 128GB SSD, Win7 64 bit. It's a Sony Vaio Z11. Approx 18 months old. When running something computationally intensive, the fan starts up and after about 30 secs it just powers itself down with no warning. I guess it is overheating. There is nothing in the event logs to suggest what is causing it - the only thing I see is "the last system shutdown was unexpected" or something similar. This is a problem for me because I use a lot of number crunching apps, which pretty much makes it useless to me. I would like to know if there is anything I can do, other than the obvious things I've done already - open up and clean out dust, re-install the OS. According to my brother, this problem started about 6 months ago when it was already outside warranty. If it's just used for simple things - web browsing, word processing etc, the problem does not occur. Any ideas for what I can do to fix this ? Update: I found that the laptop has 2 hardware settings for graphics: Speed and Stamina - the Speed setting seems to use an nvidia GEforce GT 330M, while the Stamina setting uses an Intel chipset. With the setting on Speed, I can hear the fan the whole time, and the system powers down after a short while (5-10 mins) even just doing basic tasks (browsing this site for example), but doesn't shut down if I just leave it switched on. In this mode it also sometimes just freezes the screen and I have to power off myself. However on Stamina setting it only powers down when doing number crunching and never freezes the screen.

    Read the article

  • How to create domain or router-level workgroup (dd-wrt micro)

    - by Anthony
    In Windows, is active directory required for using "Domain" instead of "workgroup"? Do I need to register a domain with a DNS provider like godaddy? What I really want to do is set up my home LAN so that everyone connecting to the main router (which is everyone, which is about 30 people) can see each other. I've tried having everyone use the same work group name, still hit or miss. I tried setting the domain name and host name on the router itself, still nothing. I've tried joining the domain name I set instead of work group, and I get an AD error. But ideally, everyone who is connected to the main router should simply just see each other and any shared folders. I've had this problem when I was not the network admin on other large LANs, and I've never been able to figure out why sometimes people disappear or never see each other. I'd really prefer using the native sharing functionality in the OS to setting up an internal FTP or Samba server, etc. Any sure-fire ways to fix this? (maybe an open source clone of AD?) Thanks!

    Read the article

  • Intermittent NFS lockups on Isilon cluster

    - by blackbox222
    We have an Isilon cluster with 8 IQ 12000x nodes which exports storage via several NFS shares for a handful of Linux and Solaris clients. There is a Linux system that has one of these NFS filesystems mounted. I/O to this filesystem is moderately heavy from the Linux system. Every 3-4 weeks (it's not on any kind of discernible schedule, and sometimes is more/less frequent than this), we notice that all activity ceases on this NFS mount (the process hangs, as if the network stopped working so process is stuck in uninterruptible sleep) - 30 minutes later, the share recovers and things continue to work normally. The kernel log from the affected machine is as follows: Dec 3 10:07:29 redacted kernel: [8710020.871993] nfs: server nfs-redacted not responding, still trying Dec 3 10:37:17 redacted kernel: [8711805.966130] nfs: server nfs-redacted OK relevant /etc/fstab line: nfs-redacted:/ifs/nfs/export_data/shared/...redacted... /data nfs defaults 0 0 I've checked to see if there are any scheduled processes e.g. cron jobs, Isilon related functions e.g. snapshots, etc that might be causing these hangups but I can't seem to find anything. I'm also not aware of any network related issues or maintenance that would cause this. All of the lockups last almost exactly 30 minutes per the kernel logs. Perhaps someone has some suggestions I could try? (I considered a soft mount to avoid the problems associated with processes accessing the filesystem hanging; however am wary of the corruption that could result and it would not really solve the underlying issue anyway).

    Read the article

  • How do I ensure a process is running, even if it kills itself? (it needs to be restarted then)

    - by le_me
    I'm using linux. I want a process (an irc bot) to run every time I start the computer. But I've got a problem: The network is bad and it disconnects often, so I need to manually restart the bot a few times a day. How do I automate that? Additional information: The bot creates a pid file, called bot.pid The bot reconnects itself, but only a few times. The network is too bad, so the bot kills itself sometimes because it gets no response. What I do currently (aka my approach ;) ) I have a cron job executing startbot.rb every 5 minutes. (The script itself is in the same directory as the bot) The script: #!/usr/bin/ruby require 'fileutils' if File.exists?(File.expand_path('tmp/bot.pid')) @pid = File.read(File.expand_path('tmp/bot.pid')).chomp!.to_i begin raise "ouch" if Process.kill(0, @pid) != 1 rescue puts "Removing abandoned pid file" FileUtils.rm(File.expand_path('tmp/bot.pid')) puts "Starting the bot!" Kernel.exec(File.expand_path('./bot.rb')) else puts "Bot up and running!" end else puts "Starting the bot!" Kernel.exec(File.expand_path('./bot.rb')) end What this does: It checks if the pid file exists, if that's true it checks if kill -s 0 BOT_PID == 1 (if the bot's running) and starts the bot if one of the two checks fail/are not true. My approach seems to be quite dirty so how do I do it better?

    Read the article

  • Keyboard's media keys are blocked by a program

    - by Mike Hanson
    I've got a Microsoft Natural Ergonomic Keyboard 4000. In addition to the regular keys, it's also got keys for Web/Home, Search, Mail, Favorites (5), Calculator, and Media functions (Mute, Volume Up/Down, and Play/Pause). Everything works most of the time, and the exception is rather odd. I use a programming system called Clarion. When that has focus, the Media keys don't work. (All the others still do.) I've also discovered that programs that I create using Clarion also block the media keys (only when they have focus). This indicates that it's probably something in Clarion's Run-Time Library (RTL) that's causing the trouble. The keys will work if I click on a non-Clarion window before hitting the media key, but that's an undesirable hassle. The odd thing is that I have many colleagues with the same keyboard, and they have no problem. When I recently upgraded from Vista Professional to Win7 Ultimate, I noticed that various things "appear" differently. For example, with my old system, when I changed the volume or muted the volume bar visualization always appeared at the bottom right on the screen. Now it doesn't appear in certain programs, even when it works. This indicates an order of precedence for visual elements. I'm fairly certain a similar order of precedence exists for keyboard hooks. Depending on how the hooks are defined, and the order in which they're applied, it would seem that sometimes the IntelliType drivers don't see the media keystrokes. The Media keys probably behave differently than the rest of the "special" keys, because they are more of a standard across all keyboards, so perhaps are handled by a different driver hooking mechanism. Does anyone have any suggestions of how I might fix this problem? Is there some way to change the order of hooks? Delay the loading of the IntelliType driver? Thanks in advance!

    Read the article

  • How make rewrite rules relative to .htaccess file.

    - by Kendall Hopkins
    Current I have an .htaccess file like this. RewriteEngine On RewriteCond %{REQUEST_FILENAME} !-f [OR] RewriteCond %{REQUEST_URI} ^/(always|rewrite|these|dirs)/ [NC] RewriteRule ^(.*)$ router.php [L,QSA] It works create when the site files are in the document_root of the webserver (ie. domain.com/abc.php - /abc.php). But in our current setup (which isn't changeable), this isn't ensured. We can sometimes have arbitrary folder in between the document root and folder of the .htaccess file (ie. domain.com/something/abc.php - /something/abc.php). The only problem with is that is the second RewriteCond no longer works. Is there anyway to dynamically check if the accessed path by a path relative to .htaccess file. For Example: If I have a site where domain.com/rewrite/ is the directory of the .htaccess file. NOT FORCED TO REWRITE -> domain.com/rewrite/index.php FORCED TO REWRITE -> domain.com/rewrite/rewrite/index.php If I have a site where domain.com/ is the directory of the .htaccess file. NOT FORCED TO REWRITE -> domain.com/index.php FORCED TO REWRITE -> domain.com/rewrite/index.php

    Read the article

  • Synaptics touchpad stops working randomly

    - by Jus12
    I have two laptops. One dell Vostro and other Vaio Z. Both have Synaptics (Yes, I have checked, and the original drivers were from Synaptics as well). On both laptops, the touchpad scrolling stops working at some arbitrary time and nothing seems to solve it except a reboot. Sometimes, it randomly starts working again. I have downloaded all latest drivers from OEM. Interestingly, when I run a program as Administrator, scrolling works in that window only. This problem is very odd. It happens without any reason and I've not been able to find a fix for more than a year. I have seen some unusual suggestions on forums (e.g., to "restore windows to a previous working state") but never any fix that solves this issue properly. I have tried installing latest drivers and I DO NOT want to restore windows to a previous working configuration. OS: Windows 7 64 bit Professional (Sony Vaio Z - VPCZ128GG) Windows 7 32 bit Professional (Dell) Edit: Temporary solution is to uninstall the synaptics driver and let Windows 7 use its default built in one. However, I really prefer the Synaptic driver because it activates the scroll button rather than the mouse wheel (useful in some apps such as MS Photo Editor)

    Read the article

  • Motherboard running rather hot while gaming

    - by I take Drukqs
    Case: Antec 1200 Mobo: Gigabyte GA-X58A-UD3R CPU: Intel i7 950 (stock cooler) GPU: EVGA GeForce 570 GTX RAM: 2x 2 GB (4 GB total) DDR3 dual-channel Corsair OS: Windows 7 Home Premium 64-bit This is my first build and it's brand new. I had no problems putting it all together in a few hours one evening and I consider myself to be pretty good with computers. Not to brag or anything like that! Just saying I've been fiddling with them since I was in diapers and I have a good amount of experience under my belt, just not with certain things yet. Recently while playing many of the latest games maxed out without a hitch my motherboard has been running hot and like anyone who's ever built a computer it scares the life out of me. I checked HWMonitor and saw that my motherboard sometimes reached temperatures of around 52 - 78c (the number 78 obviously being what's scaring me). I was wondering if such a temperature is normal and if not what the problem could be. Air flow in my case is phenomenal and besides having to ship back a faulty GPU and reseat my CPU my first build has been a very large success which I am enjoying tremendously. There is literally almost no dust in my case due to it being very new as previously mentioned and my RAM sticks are in the correct slots for dual-channel mode. My cable management is pretty great in my opinion with only cables from my PSU lingering in the bottom of the case. At any given opportunity I ran my cables behind my mobo. Air flow should definitely not be a problem because my CPU only goes up to about 60c and my GPU only goes up to about 80c. Thank you very much in advance.

    Read the article

< Previous Page | 240 241 242 243 244 245 246 247 248 249 250 251  | Next Page >